laboratory testing of 1 add-on evaporative cooling systems
TRANSCRIPT
![Page 1: Laboratory Testing of 1 Add-on Evaporative Cooling Systems](https://reader033.vdocuments.us/reader033/viewer/2022050611/6273621a2692382e1a0ceb4d/html5/thumbnails/1.jpg)
1 Laboratory Testing of Add-on Evaporative Cooling Systems for Rooftop Units Session 7: Evaporative cooling and pre-cooling technology advancements – are we ready for prime-time?
Robert Davis Sr. Mechanical Engineer PG&E Applied Technology Services
October 22, 2014
![Page 2: Laboratory Testing of 1 Add-on Evaporative Cooling Systems](https://reader033.vdocuments.us/reader033/viewer/2022050611/6273621a2692382e1a0ceb4d/html5/thumbnails/2.jpg)
2
Air Conditioner Performance Map
• Carrier 48DJD009 • ~22 years old • R-22 • Nominal 8½-ton capacity • 2 compressor stages • 1½-hp indoor blower, ¾-hp condenser fan
• Rated airflows 3,000 CFM Supply (0.25 IW External Resistance) 6,500 CFM Condensing
• Exhaust static pressure held to zero • Economizer OA damper closed and sealed • All tests done with return air at 80°Fdb / 67°Fwb
Test Unit
![Page 3: Laboratory Testing of 1 Add-on Evaporative Cooling Systems](https://reader033.vdocuments.us/reader033/viewer/2022050611/6273621a2692382e1a0ceb4d/html5/thumbnails/3.jpg)
3
But it’s a dry heat!
![Page 4: Laboratory Testing of 1 Add-on Evaporative Cooling Systems](https://reader033.vdocuments.us/reader033/viewer/2022050611/6273621a2692382e1a0ceb4d/html5/thumbnails/4.jpg)
4
Evaporative Pre-Cooler Lab Testing Challenges
• Treatment of humidified air • Condense it out • Desiccant drying • Exhausting
• Difficult to accurately measure air properties between pre-cooler and condenser coil
• Little air mixing • Uneven wetting • Carry-over spray • Radiant effects from coil
• Water treatment • Continuous versus intermittent flows • Quality (dissolved solids)
![Page 5: Laboratory Testing of 1 Add-on Evaporative Cooling Systems](https://reader033.vdocuments.us/reader033/viewer/2022050611/6273621a2692382e1a0ceb4d/html5/thumbnails/5.jpg)
5
Evaporative Effectiveness Metrics Temperature Effectiveness
Humidity Ratio Effectiveness
inin
outin
wbdb
dbdb
TTTTEE
−
−=
inwbsat
inout
WWWWEE
in −
−=
,
*
Water Consumption for Evaporation: GPH = 60 × (Wout – Win) × CFM × 0.075 lbA/ft³ / 8.33 lb H2O/gal
≈ (Wout – Win) × CFM / 2 ≈ (Tdbin – Tdbout) × CFM / 8600 ≈ EE × WBD × CFM / 8600
![Page 6: Laboratory Testing of 1 Add-on Evaporative Cooling Systems](https://reader033.vdocuments.us/reader033/viewer/2022050611/6273621a2692382e1a0ceb4d/html5/thumbnails/6.jpg)
6
PG&E Laboratory San Ramon
Two independently conditioned rooms 15’H × 15’W × 16’7”L (small “indoor room” on left), and 15’H × 15’W × 23’9”L (large “outdoor room” on right) Airflow measurement with nozzle boxes (“Code Testers”) on roof • 65 – 5,500 CFM indoor • 500 – 13,500 CFM outdoor • Variable speed booster fans to compensate for nozzle and duct pressure loss
Separate space conditioning systems for each room • Variable capacity heat pumps with supplemental resistance heat • Fully functional outside air intakes for flushing humidified air
![Page 7: Laboratory Testing of 1 Add-on Evaporative Cooling Systems](https://reader033.vdocuments.us/reader033/viewer/2022050611/6273621a2692382e1a0ceb4d/html5/thumbnails/7.jpg)
7
Addition of Dry Pre-Cooler Creates extra resistance to condenser airflow
![Page 8: Laboratory Testing of 1 Add-on Evaporative Cooling Systems](https://reader033.vdocuments.us/reader033/viewer/2022050611/6273621a2692382e1a0ceb4d/html5/thumbnails/8.jpg)
8
Calculating Evaporative Effectiveness from the Performance Map
![Page 9: Laboratory Testing of 1 Add-on Evaporative Cooling Systems](https://reader033.vdocuments.us/reader033/viewer/2022050611/6273621a2692382e1a0ceb4d/html5/thumbnails/9.jpg)
9
Condenser Air Evaporative Pre-Cooling Four systems tested of different configurations and approaches
Pre-Cooler Face
Velocity
3.1 fps
4.2 fps
5.2 fps
4.9 fps
![Page 10: Laboratory Testing of 1 Add-on Evaporative Cooling Systems](https://reader033.vdocuments.us/reader033/viewer/2022050611/6273621a2692382e1a0ceb4d/html5/thumbnails/10.jpg)
10
RTU Performance with Wet Pre-Cooler
PC1 PC2
PC3 PC4
![Page 11: Laboratory Testing of 1 Add-on Evaporative Cooling Systems](https://reader033.vdocuments.us/reader033/viewer/2022050611/6273621a2692382e1a0ceb4d/html5/thumbnails/11.jpg)
11
Relative Performance Improvements “Net” means including added pump power
PC1 PC2
PC3 PC4
![Page 12: Laboratory Testing of 1 Add-on Evaporative Cooling Systems](https://reader033.vdocuments.us/reader033/viewer/2022050611/6273621a2692382e1a0ceb4d/html5/thumbnails/12.jpg)
12
Water Consumption
PC1 PC2
PC3 PC4
![Page 13: Laboratory Testing of 1 Add-on Evaporative Cooling Systems](https://reader033.vdocuments.us/reader033/viewer/2022050611/6273621a2692382e1a0ceb4d/html5/thumbnails/13.jpg)
13
Water Use per Unit of Energy Saved
PC1 PC2
PC3 PC4
Continuous and Adjusted for the Capacity Improvement
![Page 14: Laboratory Testing of 1 Add-on Evaporative Cooling Systems](https://reader033.vdocuments.us/reader033/viewer/2022050611/6273621a2692382e1a0ceb4d/html5/thumbnails/14.jpg)
14
Conclusions • Many systems can produce a significant improvement in RTU
performance • Up to 14% Demand Reduction (maximum observed) • Up to 29% Capacity Improvement (maximum observed)
• May allow system to operate less frequently
• Impact is greater at higher wet bulb depressions • Appears to affect power and capacity differently
• May be related to airflow restriction
• Results representative of only one test RTU and Pre-cooler samples • R-410a systems likely to be more responsive • “Your mileage may vary”