kv28fq86e
TRANSCRIPT
- 1 -
SERVICE MANUAL AE-6BA CHASSISMODEL COMMANDER DEST CHASSIS NO.
KV-28FQ86B RM-945 FR SCC-Q83T-A
KV-28FQ86E RM-945 ESP SCC-Q81W-A
MODEL COMMANDER DEST CHASSIS NO.
KV-32FQ86
RM-945
KV-32FQ86B RM-945 FR SCC-Q83U-A
KV-32FQ86E RM-945 ESP SCC-Q81X-A
KV-32FQ86K RM-945 OIRT SCC-Q82M-A
KV-32FQ86U RM-945 UK SCC-Q84T-A
- 2 -
TABLE OF CONTENTS
Section Title Page Section Title Page
Caution .................... 3Specifications .................... 4Connectors .................... 6Self Diagnostic Software .................... 7
1. GENERALSwitching On the TV andAutomatically Tuning .................... 8Introducing and Using the MenuSystem .................... 9The Picture Adjustment Menu .................... 9The Sound Adjustment Menu .................... 10PAP (Picture and Picture) .................... 10Teletext .................... 11Remote Control Configurationfor VCR or DVD .................... 11Technical Specifications .................... 12Lifting the TV Set .................... 12Troubleshooting .................... 13
2. DISASSEMBLY
2-1. Rear Cover Removal .................... 142-2. Speaker Connector Disconnection................ 142-3. Chassis Removal and Refitting .................... 142-4. Service Position .................... 152-5. G Board Removal .................... 152-6. D2 Board Removal .................... 152-7. D Board Removal .................... 152-8. Picture Tube Removal .................... 16
Bottom Plates .................... 17
3. SET-UP ADJUSTMENTS
3-1. Beam Landing .................... 183-2. Convergence .................... 193-3. Focus Adjustment .................... 213-4. Screen (G2), White Balance .................... 21
4. CIRCUIT ADJUSTMENTS
4-1. Electrical Adjustments .................... 224-2. Test Mode 2 .................... 24
5. DIAGRAMS
5-1. Block Diagrams (1) .................... 25Block Diagrams (2) .................... 26Block Diagrams (3) .................... 27Block Diagrams (4) .................... 28
5-2. Circuit Board Location .................... 285-3. Schematic Diagrams and
Printed Wiring Boards .................... 28* A Board Schematic .................... 30* A Board PWB .................... 33* B Board Schematic .................... 35* B Board PWB .................... 37* D2 Board Schematic .................... 38* D2 Board PWB .................... 37* F1 Board Schematic .................... 39* F1 Board PWB .................... 40* H1 Board Schematic .................... 39* H1 Board PWB .................... 40* VM Board Schematic .................... 39* VM Board PWB .................... 40* G Board Schematic .................... 41* G Board PWB .................... 40* C Board Schematic .................... 42* C Board PWB .................... 43* J Board Schematic .................... 44* J Board PWB .................... 43* D Board Schematic .................... 46* D Board PWB .................... 45
5-4. Semiconductors .................... 475-5. IC Blocks .................... 49
6. EXPLODED VIEWS
6-1. Chassis .................... 516-2. Picture Tube .................... 52
7. ELECTRICAL PARTS LIST .................... 53
CAUTION
SHORT CIRCUIT THE ANODE OF THE PICTURE TUBE AND THEANODE CAP TO THE METAL CHASSIS, CRT SHIELD, OR THECARBON PAINTED ON THE CRT, AFTER REMOVAL OF THEANODE CAP.
WARNING !!
AN ISOLATION TRANSFORMER SHOULD BE USED DURINGANY SERVICE WORK TO AVOID POSSIBLE SHOCK HAZARDDUE TO LIVE CHASSIS, THE CHASSIS OF THIS RECEIVER ISDIRECTLY CONNECTED TO THE POWER LINE.
SAFETY-RELATED COMPONENT WARNING !!
COMPONENTS IDENTIFIED BY SHADING AND MARKED ONTHE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THEPARTS LIST ARE CRITICAL FOR SAFE OPERATION. REPLACETHESE COMPONENTS WITH SONY PARTS WHOSE PARTNUMBERS APPEAR AS SHOWN IN THIS MANUAL OR INSUPPLEMENTS PUBLISHED BY SONY.
ATTENTION
APRES AVOIR DECONNECTE LE CAP DE’LANODE,COURT-CIRCUITER L’ANODE DU TUBE CATHODIQUE ETCELUI DE L’ANODE DU CAP AU CHASSIS METALLIQUE DEL’APPAREIL, OU AU COUCHE DE CARBONE PEINTE SUR LETUBE CATHODIQUE OU AU BLINDAGE DU TUBECATHODIQUE.
ATTENTION !!
AFIN D’EVITER TOUT RISQUE D’ELECTROCUTIONPROVENANT D’UN CHÁSSIS SOUS TENTION, UNTRANSFORMATEUR D’ISOLEMENT DOIT ETRE UTILISÈ LORSDE TOUT DÈPANNAGE LE CHÁSSIS DE CE RÈCEPTEUR ESTDIRECTMENT RACCORDÈ Á L’ALIMENTATION SECTEUR.
ATTENTION AUX COMPOSANTS RELATIFS ÁLA SECURITÈ!!
LES COMPOSANTS IDENTIFIÈS PAR UNE TRAME ET PAR UNEMARQUE SUR LES SCHÈMAS DE PRINCIPE, LES VUESEXPLOSÈES ET LES LISTES DE PIECES SONT D’UNE IMPOR-TANCE CRITIQUE POUR LA SÈCURITÈ DU FONCTIONNEMENT,NE LES REMPLACER QUE PAR DES COMPSANTS SONY DONTLE NUMÈRO DE PIÈCE EST INDIQUÈ DANS LE PRÈSENTMANUEL OU DANS DES SUPPLÈMENTS PUBLIÈS PAR SONY.
- 3 -
CAUTION
Lead Free Soldered Boards
The circuit boards listed below [Table 1] used in these modelsmay have been processed using Lead Free Solder. The boards areidentified by the LF logo located close to the board designatione.g. F1, H1 etc [ see examples ]. The servicing of these boardsrequires special precautions to be taken as outlined below.
Table 1
example 1
example 2
It is strongly recommended to use Lead Free Solder material in order to guarantee optimal quality of new solder joints. Lead Free Solder isavailable under the following part numbers :
Due to the higher melting point of Lead Free Solder the soldering iron tip temperature needs to be set to 370 degrees centigrade. Thisrequires soldering equipment capable of accurate temperature control coupled with a good heat recovery characteristics.
For more information on the use of Lead Free Solder, please refer to http://www.sony-training.com
rebmuntraP retemaiD skrameR
91-500-046-7 mm3.0 gK52.0
02-500-046-7 mm4.0 gK05.0
12-500-046-7 mm5.0 gK05.0
22-500-046-7 mm6.0 gK52.0
32-500-046-7 mm8.0 gK00.1
42-500-046-7 mm0.1 gK00.1
52-500-046-7 mm2.1 gK00.1
62-500-046-7 mm6.1 gK00.1
draoB noitcnuF
A,srotalugeR,renuT,noitcelfeD,oiduA
ecafretnIB,J
B ecafretnI_A,SDVL,etarnacS,dnekcaB
C tuOB,G,R
D noitcelfeD
2D noitcelfeDedoMtramS
1FybdnatS/SCRIS/esuF/hctiwSrewoP
DEL
G ylppuSrewoP
1HdnaenohpdaeH/tupnIVAtnorF
sehctiwSlortnoC
J stekcoSdnagnihctiwSO/ItracSVA
MV noitaludoMyticoleV
- 4 -
LEDOMMETI metsySnoisiveleT metsySoeretS egarevoClennahC metsySroloC
B L,I,K/D,H/G/BMACIN/NAMREG
oeretS
Q-B,01F-20F,30S-10S,21R-1R,21E-2E:FHV96R-12R,96B-12B,96F-12F,96E-12E:FHU
02S-10S:VTELBAC14S-12S:REPYH
MACES,LAP85.3CSTN,34.4CSTN
)NIOEDIV(
E K/D,H/G/BMACIN/NAMREG
oeretS
,30S-10S,21R-1R,21E-2E:FHV96R-12R,96E-12E:FHU
02S-10S:VTELBAC14S-12S:REPYH
MACES,LAP85.3CSTN,34.4CSTN
)NIOEDIV(
K K/D,H/G/BMACIN/NAMREG
oeretS
30S-10S,21R-1R,21E-2E:FHV96R-12R,96E-12E:FHU
02S-10S:VTELBAC14S-12S:REPYH
MACES,LAP85.3CSTN,34.4CSTN
)NIOEDIV(
U I oeretSMACIN 96B-12B:FHUIMACES,LAP
85.3CSTN,34.4CSTN)NIOEDIV(
ebuTerutciP
:EDIWnortinirTDFyalpsiDtalF
)sehcni82(mc17xorppA)68QF82-VK(
)sehcni23(mc28xorppA)68QF23-VK(
tuptuodnuoS
rekaepstfeLdnathgiR
refooWbuS
)SMR(W01x2)rewoPcisuM(W02x2
)SMR(W51x1)rewoPcisuM(W03x1
]RAER[slanimreTtuptuO/tupnI snoitacificepSlareneG
rotcennocoruEnip-12:1)dradnatsCELENEC(
.slangisoediVdnaoiduArofstupnI.BGRrofstupnI
oiduAdnaoediVVTfostuptuO.slangis
stnemeriuqeRrewoP V042-022
noitpmusnoCrewoP W5.0/W031
rotcennocoruEnip-12:2
.slangisoediVdnaoiduArofstupnI.BGRrofstupnI
.slangisoiduAdnaoediVVTfostuptuO)tuOrotinoM(
snoisnemiD)68QF82-VK(mm015x335x987xorppA)68QF23-VK(mm685x685x019xorppA
thgieW)68QF82-VK(gk54xorppA)68QF23-VK(gk46xorppA
rotcennocoruEnip-12:3.slangisoediVdnaoiduArofstupnI
.oediVSrofstupnI.slangisoiduAdnaoediVVTfostuptuO
ecafretnIkniltramS,)elbatceles(
seirosseccAdeilppuS)1(rednammoCetomeR549-MR
)2(yrettab6RdetangisedCEI
skcaJonohP oiduArofelbairavsrotcennoCtuptuOslangiS
serutaeFrehtO,weiVTxeN,sulPlatigiD,erutcipzH001
ybloD,latigiDEBB,kniltramS,txeteleTICA,PAP,lautriV
]TNORF[slanimreTtuptuO/tupnI lortnoCderarfnI:metsySlortnoCetomeR
kcajenohpdaeH kcajinimoerets
stnemeriuqerrewoPcdV3
noitangisedCEIseirettab2)AAezis(6R
stupnioiduA skcajonohp
stupnioediV skcajonohp
tupnioediVS NIDnip4
.ecitontuohtiwegnahcottcejbuserasnoitacificepsdnangiseD
- 5 -
How to replace the fuse.Open the fuse compartment witha screwdriver blade and replacethe fuse.
FUSE
WARNING (UK Models only)
The flexible mains lead is supplied connected to a B.S. 1363 fusedplug having a fuse of 5 AMP rating. Should the fuse need to bereplaced, use a 5AMP FUSE approved by ASTA to BS 1362, ie onethat carries the ASAT mark.
IF THE PLUG SUPPLIED WITH THIS APPLIANCE IS NOT SUIT-ABLE FOR THE OUTLET SOCKETS IN YOUR HOME, IT SHOULDBE CUT OFF AND AN APPROPRIATE PLUG FITTED. THE PLUGSEVERED FROM THE MAINS LEAD MUST BE DESTROYED AS APLUG WITH BARED WIRES IS DANGEROUS IF ENGAGED IN ALIVE SOCKET.
When an alternative type of plug is used, it should be fitted with a5 AMP FUSE, otherwise the circuit should be protected by a 5AMPFUSE at the distribution board.
emaNledoMmetI
B68QF82-VK E68QF82-VK B68QF23-VK E68QF23-VK K68QF23-VK U68QF23-VK
bmoClaP FFO FFO FFO FFO FFO FFO
PAP NO NO NO NO NO NO
ytiroirPBGR NO NO NO NO NO NO
xoBrefooW NO NO NO NO NO NO
1tracS NO NO NO NO NO NO
2tracS NO NO NO NO NO NO
3tracS NO NO NO NO NO NO
)4(nitnorF NO NO NO NO NO NO
rotcejorP FFO FFO FFO FFO FFO FFO
G/BmroN NO NO NO NO NO FFO
ImroN NO FFO NO FFO FFO NO
K/DmroN NO NO NO NO NO FFO
SUAmroN FFO FFO FFO FFO FFO FFO
LmroN NO FFO NO FFO FFO FFO
TASmroN FFO FFO FFO FFO FFO FFO
MmroN FFO FFO FFO FFO FFO FFO
txeteleT NO NO NO NO NO NO
oeretSmaciN NO NO NO NO NO NO
- 6 -
Connected Not Connected (open) * at 20Hz - 20kHz
Pin No 1 2 4 Signal Signal level
1 Audio output B(right)
Standard level : 0.5V rmsOutput impedence : Less than 1kohm*
2Audio input B(right)
Standard level : 0.5V rmsOutput impedence : More than 10kohm*
3Audio output A(left)
Standard level : 0.5V rmsOutput impedence : Less than 1kohm*
4 Ground (audio)
5 Ground (blue)
6 Audio input A(left)
Standard level : 0.5V rmsOutput impedence : More than 10kohm*
7 Blue input 0.7 +/- 3dB, 75 ohms positive
8 Function select(AV control)
High state (9.5-12V) : Part mode Low state (0-2V) : TV modeInput impedence : More than 10K ohmsInput capacitance : Less than 2nF
9 Ground (green)
10 Open
11 Green Green signal : 0.7 +/- 3dB, 75 ohms, positive
12 Open
13 Ground (red)
14 Ground (blanking)
15
_ _ Red input 0.7 +/- 3dB, 75 ohms, positive
_ (S signal Chroma input)
0.3 +/- 3dB, 75 ohms, positive
16 Blanking input(Ys signal)
High state (1-3V) Low state (0-0.4V)Input impedence : 75 ohms
17 Ground (video output)
18 Ground (video input)
19 Video output 1V +/- 3dB, 75ohms, positive sync 0.3V(-3+10dB)
20
_ _ Video input 1V +/- 3dB, 75ohms, positive sync 0.3V(-3+10dB)
_ Video inputY (S signal)
1V +/- 3dB, 75ohms, positive sync 0.3V(-3+10dB)
21 Common ground(plug, shield)
21 pin connector
19
17
15
13
11
9
7
5
3
1
20
18
16
14
12
10
8
6
4
2
21
Rear Connection Panel Front Connection Panel
noitarugifnocniptekcosoediVS
niPoN
langiS leveLlangiS
1 dnuorG -
2 dnuorG -
3 tupni)langisS(Y ,mho57Bd3-/+V1V3.0.cnySevitisop
Bd01+3-
4 tupni)langisS(C Bd3-/+V3.0evitisop,mho57
.cnyS
S-Videosocket
3
- 7 -
egasseMrorrEDELedoC
rorreoN 00devreseR 10
)noitcetorPtnerruCrevO(PCO 20noitcetorPegatloVrevO 30
cnySlacitreVoN 40norewoptarorrERKI 50
norewoptawolsenilatadro/dnakcolcsubCII 60norewoptaegdelwonkcasubCIIonMVN 70
noitcetorPlatnoziroH 80norewoptaegdelwonkcaonrenuT 90
rorrErossecorPdnuoS 01devreseR 11
rorrEetarnacS 21rorrECAD 31
rorrEdnekcaB 41rorrEecnegrevnoCcimanyD 51
rorrEPIP 61
AE-6BA SELF DIAGNOSTIC SOFTWARE
The identification of errors within the AE-6BA chassis is triggered in one of two ways :- 1: Busy or 2: Device failure to respond to IIC. In theevent of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with a continuousflashing LED) and then communicate with each device in turn to establish if a device is faulty. If a device is found to be faulty the relevantdevice number will be displayed through the LED (Series of flashes which must be counted) See table 1, non fatal errors are reported using thismethod. Each time the software detects an error it is stored within the NVM. See Table 2.
Table 1How to enter into Table 2
1. Turn on the main power switch of the TV set.2. Program Remote Commander for Operation in Service
Mode. [See Page 22].3. Press ‘AUX/VIDEO’ ‘AUX/VIDEO’ > ‘MENU’ on the
Remote Commander.4. Using the Remote Commander, Scroll to the ‘Error’ item
using the down arrow key, then press the right arrowkey.
5. The following table will be displayed indicating the errorcount.
Table 2
Note: To clear the error count data press ‘80’ on the Remote commander.
Flash Timing Example : e.g. error number 3
StBy LED
ON ON ON
OFF OFF
rotinomrorrE
)setuniM:sruoH(:EMITGNIKROW 33:28
:sretnuocrorrEPCO:20E 0PVO:30E 0
CNYSVON:40E 0RKI:50E 0
CII:60E 0MVN:70E 0
TORPH:80E 0RENUT:90E 0DNUOS:01E 0STLOV9:11E 0
ETARNACS:21E 0BMOCD3:31E 0DNEKCAB:41E 0
NOCNYD:51E 0EGATLOVHGIH:61E 0
HCTIWSVA:71E 0CEDAMORHC:81E 0
ACRF:91E 0GNEJP:02E 0
CAD:12E 0TORPREKAEPS:42E 0KCITSYROMEM:52E 0
:tceleS :uneMsuoiverP
- 8 -
8Sw
itchi
ng O
n th
e T
V a
nd A
utom
atic
ally
Tun
ing
The
firs
t tim
e yo
u s
witc
h on
yo
ur T
V, a
seq
uen
ce o
f men
u sc
reen
s ap
pear
on
the
TV
en
ablin
g yo
u to
: 1) c
hoo
se
the
lan
guag
e o
f the
men
u sc
reen
2) a
djus
t th
e pi
ctu
re s
lan
t, 3
) ch
eck
how
to c
onn
ect o
ptio
nal
eq
uipm
ent t
o y
our
T
V,
4) s
earc
h an
d st
ore
all a
vaila
ble
chan
nel
s (T
V B
road
cast
) a
nd 5
) ch
ange
the
ord
er
in w
hic
h th
e ch
anne
ls
(TV
Bro
adc
ast
) ap
pear
on
the
scr
een
.H
ow
eve
r, if
you
nee
d to
cha
nge
any
of t
hese
se
tting
s at
a la
ter
date
, you
can
do
so b
y se
lect
ing
the
appr
opria
te
optio
n in
the
(Set
Up
men
u) o
r b
y pr
essi
ng
the
Au
to S
tart
Up
Bu
tton
on
the
TV
se
t.
1C
onn
ect
the
TV
plu
g to
the
mai
ns
sock
et (
220
-24
0V A
C, 5
0Hz)
Th
e fir
st ti
me
tha
t the
TV
set
is c
onn
ecte
d, i
t is
usu
ally
turn
ed o
n.
If th
e T
V is
off,
pre
ss th
e
on/
off
but
ton
on
the
TV
set
to tu
rn
on th
e T
V.
Th
e fir
st ti
me
you
sw
itch
on th
e T
V, a
La
ngua
ge m
enu
dis
pla
ys
auto
ma
tica
lly o
n th
e T
V s
cre
en.
2P
ress
the V
, v, B
or b
but
ton
s on
the
rem
ote
con
tro
l to
se
lect
yo
ur la
ngu
age
, th
en p
ress
the
O
K b
utto
n to
co
nfir
m y
our
se
lect
ion.
Fro
m n
ow o
n a
ll th
e m
enus
will
app
ear
in y
our
cho
sen
lan
gua
ge.
3B
ecau
se o
f the
ea
rth
’s m
agne
tism
, the
pic
ture
mig
ht s
lant
. The
P
ictu
re R
otat
ion
men
u al
low
s yo
u to
cor
rect
the
pic
ture
sla
nt if
it
is n
eces
sary
.
a) If
it is
no
t nec
ess
ary,
pre
ss
OK
to
sele
ct Not
nec
essa
ry.
b) I
f it i
s ne
cess
ary,
pre
ss B o
r b to
sel
ect A
djus
t now
, th
en p
ress
O
K a
nd
corr
ect
any
slan
t of
the
pic
ture
be
twee
n –
5 an
d +
5 b
y pr
ess
ing v
or V
. F
inal
ly p
ress
OK
to
stor
e.
Lang
uage
En
glis
hD
eu
tsch
Esp
añ
ol
Fra
nça
isIt
alia
no
Ne
de
rla
nd
s
Po
lski
P
ort
ug
uê
sTü
rkçe
Ελ
λη
νικ
άБ
ъл
гар
ски
Sve
nsk
aP
yccк
ий
Čes
kyM
ag
yar
No
rsk
Su
om
iS
love
nsk
iR
om
ână
Sel
ect
lang
uage
Dan
sk
Ifpicture
slants,please
adjustpicture
rotation.
Notnecessary
Adjustnow
Firs
t Tim
e O
pera
tion
RM
-94
5
OK
La
ng
ua
ge
En
glish
De
uts
ch
Esp
añ
ol
Fra
nça
isIt
alia
no
Ne
de
rla
nd
s
Po
lski
Po
rtu
gu
ês
Tü
rkçe
Ελλη
νικ
άБ
ъл
гарски
Sve
nska
Pyccкий
Česky
Ma
gya
rN
ors
kS
uo
mi
Slo
ve
nski
Ro
mână
Se
lect la
ng
ua
ge
Dan
sk
Language
En
glish
De
uts
ch
Esp
añ
ol
Fra
nça
isIt
alia
no
Ne
de
rla
nd
s
Po
lski
Po
rtu
gu
ês
Tü
rkçe
Ελ
λη
νικ
άБ
ъл
гар
ск
иS
ve
nska
Pyccк
ий
Česky
Ma
gya
rN
ors
kS
uo
mi
Slo
ve
nski
Ro
mân
ă
Sele
ct language
Da
nsk
con
tinue
d...
9
GB
4A
dia
gram
will
ap
pea
r sh
owin
g y
ou h
ow to
con
nec
t a w
ide
rang
e of
eq
uipm
ent t
o y
our
TV
set
. Fo
llow
the
inst
ruct
ions
and
fina
lly
pre
ss th
e OK
but
ton
to r
em
ove
the
diag
ram
an
d co
ntin
ue
the
auto
mat
ic p
roce
ss.
Afte
r th
e au
tom
atic
tun
ing
pro
cess
has
fini
she
d an
d an
y op
tiona
l eq
uipm
ent
has
bee
n c
onne
cte
d, w
e re
com
men
d yo
u fo
llow
the
inst
ruct
ion
s ex
pla
ined
on
the
se
ctio
n
"Co
nnec
tion
Gu
ide"
on
pag
e 1
5 to
ge
t the
opt
imu
m s
ettin
gs
rela
ted
to t
he o
ptio
nal
equ
ipm
ent
.
5T
he
Aut
o T
unin
g m
enu
app
ears
on
the
scre
en.
Pre
ss th
e O
K
but
ton
to s
elec
t Yes
.
6T
he
TV
sta
rts
to a
utom
atic
ally
sea
rch
and
sto
re a
ll
ava
ilabl
e br
oad
cast
cha
nne
ls fo
r yo
u.
T
his
pro
ced
ure
cou
ld ta
ke s
om
e m
inut
es.
Ple
ase
be
pat
ient
an
d do
not
pre
ss a
ny b
utto
ns,
oth
erw
ise
aut
omat
ic tu
nin
g w
ill n
ot b
e co
mp
lete
d.
In s
om
e co
unt
ries
the
TV
Bro
adca
ster
inst
alls
the
ch
ann
els
auto
ma
tica
lly (
AC
I sys
tem
). In
this
cas
e, t
he T
V
Bro
adc
ast
er s
end
s a
men
u in
wh
ich
you
can
sel
ect y
our
city
by
pre
ssin
g th
e v o
r V b
utt
on a
nd O
K to
sto
re th
e ch
ann
els.
If no
cha
nnel
s w
ere
fou
nd d
urin
g th
e au
to tu
ne p
roce
ss, a
m
ess
age
appe
ars
au
tom
atic
ally
on
the
scr
een
ask
ing
you
to
conn
ect
the
aeria
l. C
heck
the
ae
rial c
onn
ectio
n (
refe
r to
pa
ge 7
). P
ress
the
O
K b
utto
n to
re
star
t th
e au
to tu
ning
pr
oce
ss.
7A
fter
all
avai
labl
e ch
anne
ls a
re c
apt
ure
d an
d s
tore
d,
th
e P
rogr
amm
e S
ortin
g m
enu
aut
omat
ical
ly a
ppe
ars
on
the
scre
en e
nab
ling
you
to c
han
ge t
he o
rder
in
whi
ch th
e ch
ann
els
are
sto
red
.
a)If
yo
u w
ish
to k
eep
the
bro
adca
st c
han
nel
s in
the
tune
d o
rder
, go
to s
tep
8.
b)If
you
wis
h to
sto
re t
he c
han
nel
s in
a d
iffer
ent o
rde
r:
1P
ress
the v
or V
bu
tton
to s
elec
t th
e pr
ogra
mm
e nu
mb
er w
ith th
e ch
ann
el (
TV
Bro
adca
st)
you
wis
h
to m
ove
. P
ress
the
b
bu
tton.
2P
ress
the v
or V
bu
tton
to s
elec
t th
e ne
wpr
ogr
am
me
num
ber
pos
itio
n fo
r yo
ur s
elec
ted
ch
ann
el (
TV
Bro
adca
st).
Pre
ss th
e O
K b
utto
n to
sto
re.
3R
epea
t st
eps
b)1
an
d b)
2 if
yo
u w
ish
to c
han
ge
the
ord
er o
f the
oth
er c
han
nel
s.
8 P
ress
the M
EN
U b
utto
n to
rem
ove
the
men
u fr
om
the
scr
een
Auto
Tunin
g
Pro
gra
mm
es found:
4
No c
hannel fo
und.
Ple
ase c
onnect aerial
Confirm
Pro
gra
mm
e S
ort
ing
01
02
03
04
05
06
07
08
TV
E
TV
E2
TV
3
C33
C27
C58
S02
S06
Pro
gra
mm
e S
ort
ing
01
TV
E
01
02
03
04
05
06
07
08
TV
E
TV
E2
TV
3
C33
C27
C58
S02
S06
Do y
ou w
ant to
sta
rt
auto
matic tunin
g?
Yes
No
OK
Ple
ase c
onnect your
equip
ment
accord
ing to this
chart
:1/ 1
:2/ 2
:3/
q3
DV
D
Your
TV
is n
ow
rea
dy
for
use
Firs
t Tim
e O
pera
tion
RM
-94
5
OK
ME
NU
The
ope
ratin
g in
stru
ctio
ns m
entio
ned
here
are
par
tial a
bstr
acts
fro
m t
he ‘O
pera
ting
Inst
ruct
ion
Man
ual’.
The
pag
e nu
mbe
rs o
f th
e ‘O
pera
ting
Inst
ruct
ion
Man
ual’
rem
ain
as in
the
man
ual.
SECTION 1 GENERAL
- 9 -
10Intr
oduc
ing
and
Usi
ng th
e M
enu
Sys
tem
Yo
ur T
V u
ses
an O
n-S
cree
n m
enu
sys
tem
to g
uid
e yo
u th
rou
gh th
e op
era
tions
. Use
the
follo
win
g b
utto
ns o
n
the
Rem
ote
Co
ntro
l to
ope
rate
the
men
u s
yste
m:
1T
o sw
itch
on th
e m
enu
scre
ens:
Pre
ss th
e ME
NU
but
ton
to s
witc
h th
e fir
st le
vel m
enu
on.
Pic
ture
Adj
ustm
ent
Sel
ect:
Ent
er:
OK
Exi
t:M
ENU
Pic
ture
Mod
e:Li
veC
ontr
ast:
Res
etN
oise
Red
uctio
n:A
uto
Col
our T
one:
Coo
lP
ictu
re A
djus
tmen
t
Sel
ect:
Ent
er:
OK
Exi
t:M
ENU
Pic
ture
Mod
e:Li
veC
ontr
ast:
Res
etN
oise
Red
uctio
n:A
uto
Col
our T
one:
Coo
l
TV
Fun
ctio
ns2T
o na
viga
te th
roug
h th
e m
enus
:
• T
o hi
ghl
igh
t an
d se
lect
the
des
ired
men
u o
r op
tion,
pre
ss v
or V
.
• T
o en
ter
the
sele
cted
men
u o
r op
tion,
pre
ss
OK
or b
.
• T
o re
turn
to th
e la
st m
enu
or
optio
n, p
ress
O
K o
r B.
• T
o al
ter
the
setti
ngs
of y
our
sele
cted
opt
ion,
pre
ss
v/V
/B o
r b.
• T
o co
nfir
m a
nd s
tore
yo
ur s
elec
tion,
pre
ss
OK
.
3T
o sw
itch
off t
he m
enu
scre
ens:
Pre
ss th
e ME
NU
but
ton
to r
emo
ve t
he m
enu
fro
m t
he s
cre
en.
OK
ME
NU
ME
NU
11
GB
The
Pic
ture
Adj
ustm
ent M
enu Th
e “P
ictu
re A
dju
stm
ent”
men
u al
low
s yo
u to
al
ter
the
pict
ure
set
tings
.
To
do th
is:
Pre
ss th
e ME
NU
bu
tton
an
d th
en
pres
s OK
to
ente
r th
is m
enu
. Nex
t pre
ss
v o
r V to
se
lect
the
de
sire
d op
tion
and
pre
ss
OK
. F
ina
lly r
ead
the
in
stru
ctio
ns b
elow
on
how
to
ope
rate
eac
h
optio
n.
Pic
ture
Mod
e T
his
optio
n al
low
s yo
u to
cu
stom
ise
the
Pic
ture
Mo
de b
ased
on
the
pro
gra
mm
e
you
are
wa
tchi
ng. A
fter
se
lect
ing
this
opt
ion
pres
s O
K.
Nex
t pre
ss v o
r V
rep
eate
dly
to
sele
ct:
Per
sona
l (f
or in
divi
dua
l se
ttin
gs).
Live
(fo
r liv
e br
oad
cast
pro
gra
mm
es, D
VD
an
d D
igita
l Set
Top
Bo
x re
ceiv
ers)
Mov
ie (
for
film
s).
Onc
e yo
u h
ave
sele
cted
yo
ur d
esire
d op
tion,
pre
ss
OK
to s
tore
.
"Brig
htne
ss",
"C
olo
ur"
an
d "S
har
pnes
s" l
evel
of
"Liv
e" a
nd
"Mov
ie"
mod
e a
re fi
xed
in th
e fa
cto
ry t
o ge
t the
bes
t pi
ctu
re q
ualit
y.
Con
tras
tP
ress
B o
r b t
o r
edu
ce o
r en
han
ce p
ictu
re c
ontr
ast.
Ne
xt p
ress
O
K to
sto
re.
Brig
htne
ssP
ress
B o
r b t
o d
arke
n or
brig
hten
the
pict
ure
. Nex
t pre
ss
OK
to s
tore
.
Thi
s op
tion
only
ap
pea
rs fo
r a
ltera
tion
if "P
ictu
re M
ode
" is
set
to "
Per
sona
l".
Col
our
Pre
ss B
or b
to
dec
reas
e or
to
incr
ease
co
lor
inte
nsi
ty. N
ext
pre
ss
OK
to s
tore
.
Thi
s op
tion
only
ap
pea
rs fo
r a
ltera
tion
if "P
ictu
re M
ode
" is
set
to "
Per
sona
l".
Hue
Pre
ss B
or b
to
dec
reas
e or
to in
crea
se th
e g
reen
tone
s. N
ext p
ress
O
K to
sto
re.
Thi
s op
tion
only
ap
pea
rs fo
r N
TS
C s
igna
l (e.
g. U
SA
vid
eo
tape
s).
Sha
rpne
ssP
ress
B o
r b t
o s
ofte
n o
r to
sh
arp
en th
e p
ictu
re.
Nex
t pre
ss
OK
to
stor
e.
Thi
s op
tion
only
ap
pea
rs fo
r a
ltera
tion
if "P
ictu
re M
ode
" is
set
to "
Per
sona
l".
Res
etP
ress
OK
to
rese
t the
pic
ture
to
the
fact
ory
pre
set
leve
ls.
Noi
se
Thi
s op
tion
is s
et to
Aut
o to
aut
omat
ical
ly r
edu
ce t
he s
now
y pi
ctur
e th
at m
ay b
eR
educ
tion
visi
ble
in th
e br
oadc
ast
sig
nal.
How
eve
r, it
can
be
mo
difie
d b
y pr
ess
ing
v
or V
to
se
lect
Off,
Low
, Mid
or H
igh
. F
ina
lly p
ress
OK
to s
tore
.
Col
our
Ton
eT
his
optio
n al
low
s yo
u to
alte
r th
e ti
nt o
f th
e p
ictu
re.
Aft
er s
elec
ting
this
opt
ion
p
ress
b. N
ext p
ress
v o
r V r
epea
ted
ly to
sel
ect: W
arm
(gi
ves
the
whi
te c
olou
rs
a re
d ti
nt)
, Nor
mal
(gi
ves
the
whi
te c
olo
urs
a n
eutr
al ti
nt)
, C
old
(giv
es
the
wh
ite
colo
urs
a b
lue
tint)
. Ne
xt p
ress
O
K to
sto
re.
TV
Fun
ctio
ns
RM
-94
5
OK
ME
NU
,
Pic
ture
Adj
ustm
ent
Sel
ect:
Ent
er:
OK
Exi
t:M
ENU
Pic
ture
Mod
e:Li
veC
ontr
ast:
Res
etN
oise
Red
uctio
n:A
uto
Col
our T
one:
Coo
l
Pic
ture
A
dju
stm
ent
Sele
ct:
Back:
Ente
r:
OK
Pic
ture
Mode:
Liv
e
Contr
ast:
Reset
Nois
e R
eduction:
Auto
Colo
ur
Tone:
Cool
ME
NU
- 10 -
12
The
Sou
nd A
djus
tmen
t Men
u Th
e “S
oun
d A
dju
stm
ent”
men
u al
low
s yo
u to
al
ter
the
soun
d s
ettin
gs.
To
do th
is:
Pre
ss th
e ME
NU
bu
tton
an
d pr
ess
v
to s
ele
ct
, the
n p
ress
OK
to e
nter
this
men
u. N
ext p
ress
v
or V
to s
elec
t th
e d
esir
ed o
ptio
n a
nd p
ress
O
K. F
inal
ly r
ead
the
inst
ruct
ions
bel
ow o
n h
ow
to
op
erat
e ea
ch o
ptio
n.
Sou
ndT
his
opt
ion
allo
ws
you
to c
usto
mis
e th
e S
ound
Eff
ect.
Aft
er s
elec
ting
this
Effe
cto
ptio
n p
ress
OK
. Nex
t pre
ss v o
r V r
epe
ate
dly to
se
lect
:
O
ff(F
lat r
esp
ons
e).
Nat
ural
(Enh
ance
s cl
arity
, det
ail a
nd
pres
enc
e o
f sou
nd b
y us
ing
“BB
E H
igh
De
finiti
on
Sou
nd s
yste
m”*
).
Dyn
amic
(“B
BE
Hig
h D
efin
itio
n S
ound
sys
tem
”* in
tens
ifies
cla
rity
and
p
rese
nce
of s
oun
d fo
r be
tter
inte
lligi
bili
ty a
nd
mu
sica
l rea
lism
).
D
olby
**(D
olb
y V
irtua
l, si
mul
ate
s th
e so
und
effe
ct o
f “D
olb
y S
urro
und
Pro
Virt
ual
Log
ic”)
.
On
ce y
ou
hav
e se
lect
ed y
our
des
ired
opt
ion
, pre
ss
OK
to
stor
e.
Tre
ble
Pre
ss B
or b
to d
ecr
ease
hig
her
-fre
quen
cy s
ound
s. N
ext
pre
ss
OK
to s
tore
.
Bas
sP
ress B
or b
to d
ecr
ease
or
to in
crea
se th
e lo
wer
-fre
que
ncy
soun
ds. N
ext p
ress
O
K t
o st
ore
.
Bal
ance
Pre
ss B
or b
to e
mp
hasi
se th
e le
ft o
r th
e rig
ht s
pea
ker.
Nex
t pre
ss
OK
to s
tore
.
Res
etP
ress
OK
to r
ese
t th
e so
und
to th
e fa
ctor
y p
rese
t le
vels
. Ne
xt p
ress
O
K to
sto
re.
Dua
l Sou
nd•
Fo
r a
Ste
reo
bro
adc
ast
:P
ress
v o
r V to
se
lect
Ste
reo
or M
ono.
Nex
t pre
ss OK
to
sto
re.
•F
or
a b
ilin
gual
bro
adc
ast
:
Pre
ss v
or V
to s
ele
ct M
ono
(for
mo
no c
hann
el if
ava
ilab
le),
A
(fo
r ch
ann
el 1
) o
r B (
for
chan
nel 2
). N
ext p
ress
O
K t
o st
ore
.
TV
Fun
ctio
ns
,
mS
ound
Adju
stm
ent
Sound E
ffect:
Dolb
y V
irtu
al
Tre
ble
:
Bass:
Bala
nce:
Reset
Dual S
ound:
Ste
reo
Auto
Volu
me:
Off
TV
Speakers
:O
n
Headphones S
et U
p
Sele
ct:
Ente
r:O
KE
xit:
ME
NU
Pic
ture
Adj
ustm
ent
Sel
ect:
Ent
er:
OK
Exi
t:M
ENU
Pic
ture
Mod
e:Li
veC
ontr
ast:
Res
etN
oise
Red
uctio
n:A
uto
Col
our T
one:
Coo
l
Sound A
dju
stm
ent
Sound E
ffect:
Dolb
y V
irtu
al
Tre
ble
:
Bass:
Bala
nce:
Reset
Dual S
ound:
Ste
reo
Auto
Volu
me:
Off
TV
Speakers
:O
n
Headphones S
et U
p
Sele
ct:
Back:
Ente
r:O
K
ME
NU
cont
inu
ed...
RM
-94
5
OK
ME
NU
19
GB
RM
-94
5
PR
OG
12
3
45
6
78
9
0
Navegador
Config
uracióndelS
istema
Ace
ptar
Versión
PROG+
PROG
Select:
Select:
MoveFrame
03
Sw
itchi
ng P
AP
on
and
off
1 P
ress
to
dis
pla
y P
AP
.
O
ne o
f the
scr
eens
will
be
fram
ed to
indi
cate
that
this
is
the
activ
e sc
ree
n. It
me
ans
that
wh
en y
ou w
ant t
o se
lect
th
e P
AP
sou
rce,
you
will
be
doi
ng it
in th
e a
ctiv
e sc
reen
.
2 P
ress
a
gain
to
rem
ove
PA
P.
On
the
scre
en
a b
anne
r ap
pea
rs g
uid
ing
you
on
how
to o
per
ate
PA
P.
Th
is b
anne
r w
ill d
isap
pea
r af
ter
som
e se
cond
s bu
t it c
an
alw
ays
be
disp
laye
d ag
ain
by
pre
ssin
g th
e b
utto
n.
Cha
ngin
g th
e ac
tive
scre
en
Th
is is
on
ly p
oss
ible
if th
e M
edi
a S
elec
tor
is s
et to
TV
.
To
cha
nge
the
activ
e s
cree
n (
fra
med
), p
ress
the
B o
r b b
utto
ns.
Sel
ectin
g P
AP
sou
rce
1S
elec
ting
a T
V c
hann
el:
Pre
ss th
e B b
utto
n to
sel
ect
the
left
scre
en a
s th
e ac
tive
scre
en.
Nex
t pre
ss th
e n
um
ber
bu
tton
s or
PR
OG
+/-
to s
elec
t a
TV
ch
anne
l.
Vid
eo in
put s
ign
als
can
not
be
dis
play
ed o
n th
e le
ft sc
reen
.
2 S
elec
ting
an in
put s
ourc
e:P
ress
the
b b
utto
n to
sel
ect t
he r
ight
scr
een
as th
e a
ctiv
e sc
reen
. Nex
t pre
ss r
epe
ate
dly
the
butt
on to
sho
w th
e in
put s
igna
l of t
he
conn
ecte
d e
quip
me
nt o
n r
ight
scr
een
of t
he T
V. F
or m
ore
de
tails
on
whi
ch in
put s
ymb
ol y
ou
wis
h to
ch
oose
, ple
ase
se
e se
ctio
n "
Vie
win
g pi
ctu
res
from
eq
uipm
ent
conn
ecte
d to
the
TV
" on
pag
e 2
3.
RF
sig
nal
(T
V b
road
cast
ch
ann
els)
can
not
be
dis
play
ed o
n th
e rig
ht s
cre
en.
Sel
ectin
g th
e so
und
The
so
und
of th
e ac
tive
scre
en (
fra
med
) a
lway
s co
mes
from
the
TV
sp
eake
rs.
Bes
ide
s th
at, y
ou c
an li
sten
to
the
act
ive
scre
en a
s w
ell a
s th
e n
on a
ctiv
e sc
ree
n vi
a h
eadp
hone
s.
To
do th
is:
With
the
PA
P s
witc
hed
on
, ref
er to
the
sect
ion
"The
Sou
nd A
dju
stm
ent M
enu"
, sel
ect "
Hea
dph
one
s S
et U
p"
and
set
the
opt
ion
" P
AP
Sou
nd"
acco
rdin
g yo
ur p
refe
renc
e. F
or d
eta
ils s
ee
pag
e 13
.
In P
AP
(pic
ture
and
pic
ture
) m
od
e, the
ou
tpu
t fr
om
the
Sca
rt
2/
2 is
fix
ed to
the
righ
t
pic
ture
.
TV
Fun
ctio
ns
PA
P (
PIC
TU
RE
AN
D P
ICT
UR
E)
PA
P d
ivid
es
the
scre
en
into
tw
o to
wat
ch t
wo
pict
ure
s in
for
mat
4:3
sim
ulta
neou
sly.
- 11 -
20Tel
etex
tT
elet
ext
is a
n in
form
atio
n s
ervi
ce tr
ansm
itted
by
mos
t TV
sta
tions
. T
he in
dex
pag
e o
f th
e te
lete
xt s
ervi
ce
(usu
ally
pag
e 10
0)
giv
es y
ou
info
rma
tion
on
how
to u
se th
e se
rvic
e. T
o op
erat
e te
lete
xt, u
se th
e r
emot
e co
ntr
ol
but
tons
as
indi
cate
d be
low
.
Tel
etex
t er
rors
may
occ
ur if
you
use
a c
han
nel (
TV
Bro
adca
st)
with
a w
eak
sig
nal.
To
switc
h on
Tel
etex
t :
1S
elec
t th
e br
oad
cast
ch
anne
l wh
ich
carr
ies
the
tele
text
se
rvic
e yo
u w
ish
to v
iew
.
2P
ress
the
b
utto
n on
ce t
o en
ter
Pic
ture
and
Tex
t (P
&T
) m
ode.
Th
e sc
ree
n is
div
ide
d in
to t
wo
with
the
T
ext d
ispl
ay o
n th
e le
ft a
nd
the
TV
cha
nne
l in
the
b
otto
m r
ight
cor
ner
.
3If
you
wis
h to
vie
w th
e T
ext i
n fu
ll sc
ree
n m
ode
, pre
ss
the
but
ton
a s
eco
nd ti
me.
To
sele
ct a
Tel
etex
t pag
e:In
put
the
3 d
igit
pag
e n
umb
er,
usin
g th
e nu
mbe
red
but
ton
s.•
If y
ou
make
a m
ista
ke,
rety
pe t
he c
orr
ect
pa
ge
num
ber.
• If th
e c
oun
ter o
n th
e s
creen
con
tinue
s se
arc
hin
g, i
t is
beca
use
the
pa
ge
is n
ot a
vaila
ble.
If th
is is
the
ca
se,
inpu
t ano
ther
pag
e n
umb
er.
To
acce
ss th
e ne
xt o
r pr
eced
ing
page
:P
ress
PR
OG
+ (
) or
PR
OG
- (
).
To
free
ze a
tele
text
pag
e:P
ress
/
bu
tton.
Pre
ss a
gain
to c
ance
l th
e fr
eeze
.
To
reve
al c
once
aled
info
rmat
ion
(e.g
: ans
wer
to a
qui
z):
Pre
ss
/ b
utto
n. P
ress
ag
ain
to c
onc
eal
the
info
rmat
ion.
To
sele
ct a
sub
pag
e:
A te
lete
xt p
age
ma
y co
nsi
st o
f se
vera
l sub
pa
ges.
In th
is c
ase,
one
or
mor
e a
rrow
s ap
pea
r n
ext t
o
the
pag
e nu
mbe
r an
d an
info
rma
tion
box
is d
isp
laye
d a
t th
e bo
tto
m o
f th
e sc
ree
n sh
ow
ing
the
num
ber
of
sub
pag
es c
ont
aine
d on
this
pag
e. A
s so
on a
s su
b p
ages
are
ava
ilabl
e, th
ey s
tart
to
aut
omat
ical
ly a
ppea
r. If
you
wa
nt to
sto
p th
e sh
ow
and
se
lect
you
r d
esire
d s
ub p
age
, pre
ss
B o
r b
rep
eate
dly
.
To
Sw
itch
Off
Tel
etex
t: P
ress
b
utto
n.
Fas
text Fas
text
se
rvic
e le
ts y
ou
acce
ss T
elet
ext p
ages
with
one
but
ton
pus
h.
Whe
n yo
u ar
e in
Tel
ete
xt m
ode
and
Fas
text
is b
road
cast
, a c
olo
ur c
oded
men
u a
ppea
rs a
t th
e b
otto
m o
f th
e te
lete
xt p
age.
Pre
ss th
e a
ppro
pria
te c
olo
ured
but
ton
(re
d, g
reen
, yel
low
o
r b
lue)
to
acce
ss t
he p
age
cor
resp
ondi
ng to
you
r m
enu
cho
ice.
Tel
etex
t
RM
-94
5
PR
OG
12
3
45
6
78
9
0
24Rem
ote
Con
trol
Con
figur
atio
n fo
r V
CR
or
DV
DIn
it’s
def
ault
con
ditio
n th
is r
em
ote
con
trol
will
op
erat
e th
e b
asic
func
tions
of t
his
So
ny T
V, S
ony
DV
Ds
and
m
ost S
ony
VC
Rs.
To
con
tro
l VC
Rs
and
DV
Ds
of o
ther
man
ufac
ture
rs (
and
som
e S
ony
VC
R m
ode
ls),
the
rem
ote
con
tro
l nee
ds
to b
e co
nfig
ure
d.
Add
ition
al In
form
atio
n
To
do th
is:
•B
efo
re y
ou s
tart
, lo
ok u
p th
e 3
digi
t cod
e fo
r yo
ur b
rand
of D
VD
or V
CR
from
the
list b
elow
. O
n th
ose
bra
nds
that
hav
e m
ore
than
on
e co
de,
ente
r th
e fi
rst
cod
e nu
mb
er.
•S
ony
will
en
dea
vour
to u
pda
te th
e so
ftw
are
acc
ord
ing
to m
ark
et c
han
ges.
Th
eref
ore
, ple
ase
refe
r to
the
co
de ta
ble
incl
uded
with
the
rem
ote
cont
rol f
or
late
st c
ode
se
t.
•A
sm
all l
abe
l is
add
ed in
side
the
bat
tery
do
or t
o al
low
you
to
reco
rd y
our
bra
nd c
odes
.
1P
ress
and
hol
d th
e T b
utto
n of
the
rem
ote
cont
rol f
or a
ppr
oxim
atel
y 6
se
cond
s u
ntil
the
gree
n D
VD
and
VC
R li
ght o
f th
e M
edi
a S
ele
ctor
sta
rts
flash
ing
(se
e fig
. 1).
2W
hile
the
VC
R a
nd
DV
D li
ghts
are
flas
hing
, en
ter
all t
hre
e di
gits
of t
he
cod
e fo
r yo
ur b
ran
d of
VC
R o
r D
VD
(se
e th
e li
st b
elo
w) u
sing
the
num
ber
butto
ns o
n th
e r
em
ote
cont
rol (
see
fig
. 2).
If y
our
sel
ecte
d co
de is
en
tere
d co
rrec
tly,
the
VC
R o
r D
VD
gre
en
light
(acc
ord
ing
to y
our
sel
ectio
n) w
ill b
e lit
mom
enta
rily
(see
fig.
3),
oth
erw
ise
repe
at a
ll th
e a
bove
ste
ps.
3T
urn
on
you
r V
CR
or
DV
D a
nd
chec
k th
at th
e m
ain
func
tion
s w
ork.
• If
you
r de
vice
is n
ot w
ork
ing
or
som
e o
f the
fun
ctio
ns
do n
ot w
ork
ple
ase
ch
eck
tha
t yo
u e
nter
ed th
e co
rre
ct c
ode
set
or t
ry th
e ne
xt c
ode
liste
d ag
ain
st th
e br
and
.
•N
ot a
ll br
ands
are
cov
ered
an
d n
ot a
ll m
ode
ls o
f eve
ry b
ran
d m
ay b
e co
vere
d.
4A
lway
s re
mem
ber
to p
ress
the T
or t
but
ton
until
the
gre
en li
ght i
lum
inat
es a
ccor
din
g to
th
e eq
uipm
ent
you
wan
t to
ope
rate
with
this
re
mot
e co
ntro
l: V
CR
, TV
or D
VD
.
VC
R B
rand
Lis
t
D
VD
Bra
nd L
ist
Bra
nd
Cod
eB
rand
Cod
eS
ON
Y (
VH
S)
30
1, 3
02
, 30
3,
30
8, 3
09
,36
2S
ON
Y (
BE
TA
)3
03
, 30
7, 3
10S
ON
Y (
DV
)3
04
, 30
5, 3
06A
IWA
325,
33
1, 3
51A
KA
I32
6, 3
29,
330
DA
EW
OO
342,
34
3G
RU
ND
IG35
8, 3
55,
360
, 36
1, 3
20,
351
, 366
HIT
AC
HI
327,
33
3, 3
34JV
C31
4, 3
15,
322
, 34
4, 3
52,
353
, 354
, 34
8, 3
49
LG
332,
33
8L
OE
WE
358,
35
5, 3
60,
361
, 32
0, 3
51M
AT
SU
I3
56
, 35
7O
RIO
N32
8P
AN
AS
ON
IC3
21
, 32
3P
HIL
IPS
311,
31
2, 3
13,
316
, 31
7, 3
18, 3
58,
359
,36
3, 3
64
SA
MS
UN
G33
9, 3
40,
341
, 34
5S
AN
YO
335,
33
6S
HA
RP
324
TH
OM
SO
N3
19
, 35
0, 3
65T
OS
HIB
A33
7
RM
-94
5
12
3
45
6
78
9
0
fig. 1
6 se
c.
VCR
TVDV
D
AUX
MO
DE
fig. 3
VCR
TVDV
D
AUX
MO
DE
SO
NY
001
, 02
9, 0
30,
036
, 03
7, 0
38,
039
, 04
0,
041
, 04
2, 0
43,
044
, 05
3, 0
54,
055
AIW
A02
1
AK
AI
03
2D
EN
ON
018
, 02
7, 0
20,
002
GR
UN
DIG
009
, 02
8, 0
23,
024
, 01
6, 0
03
HIT
AC
HI
025
, 02
6, 0
15,
004
, 03
5JV
C0
06
, 01
7K
EN
WO
OD
008
LG
015
, 01
4, 0
34L
OE
WE
009
, 02
8, 0
23,
024
, 01
6, 0
03
MA
TS
UI
01
3, 0
16
ON
KY
O0
22
, 03
3P
AN
AS
ON
IC01
8, 0
27,
020
, 00
2, 0
45,
04
6, 0
47P
HIL
IPS
009
, 02
8, 0
23,
024
, 01
6, 0
03,
031
PIO
NE
ER
004
, 05
0, 0
51,
052
SA
MS
UN
G0
11
, 01
4S
AN
YO
00
7S
HA
RP
01
9, 0
27
TH
OM
SO
N01
2T
OS
HIB
A00
3, 0
48,
049
YA
MA
HA
01
8, 0
27
, 02
0,
00
2
fig. 2
- 12 -
27
GB
Tec
hnic
al S
peci
ficat
ions
TV
sys
tem
: I C
olou
r sy
stem
:P
AL
SE
CA
M, N
TS
C 3
.58,
4.4
3 (
only
V
ideo
In)
Cha
nnel
Cov
erag
e:U
HF
: B
21-B
69
Pic
ture
Tub
e:F
lat
Dis
play
FD
Tri
nitr
on W
IDE
:K
V-2
8F
Q8
6U: 2
8” (a
ppr
ox. 7
1cm
. m
easu
red
dia
gona
lly)
KV
-32
FQ
86U
: 32"
(app
rox.
82c
m.
mea
sure
d d
iago
nally
)
Rea
r T
erm
inal
s•
AV
1 1/1
21-p
in s
cart
con
nect
or
(CE
NE
LEC
sta
ndar
d)
incl
udi
ng a
udio
/vid
eo in
put
, R
GB
inpu
t, T
V a
udio
/vid
eo
outp
ut.
•A
V2 2/
2
21-p
in S
cart
co
nne
cto
r (C
EN
EL
EC
sta
ndar
d)
incl
udi
ng a
udio
/vid
eo in
put
, R
GB
inp
ut, m
oni
tor a
udio
/vid
eo
outp
ut.
•A
V3
3/
3 21
-pin
Sca
rt c
onn
ect
or
(CE
NE
LEC
sta
ndar
d)
incl
udi
ng a
udio
/vid
eo in
put
, S
vid
eo in
put,
sel
ecta
ble
au
dio
/vid
eo o
utpu
t and
S
mar
tLin
k in
terf
ace.
•
a
udio
out
puts
(L
eft/
Rig
ht)
-
phon
o ja
cks
Fro
nt T
erm
inal
s•
4S
Vid
eo
inp
ut –
4 p
in
DIN
.•
4 vi
deo
inp
ut –
ph
ono
jack
.•
4
aud
io in
put
– p
hon
o ja
cks.
•
hea
dpho
nes
jack
.
Sou
nd O
utpu
t:2
x 2
0 W
(m
usic
po
wer
)2
x 1
0 W
(R
MS
)W
oofe
r:30
W (
mus
ic p
owe
r)15
W (
RM
S)
Pow
er C
onsu
mpt
ion:
KV
-28
FQ
86U
: 13
0 W
KV
-32
FQ
86U
: 13
0 W
Sta
ndby
Pow
er C
onsu
mpt
ion:
0.5
W
Dim
ensi
ons
(w x
h x
d)
:K
V-2
8F
Q8
6U:
app
rox.
789
x 5
33 x
51
0 m
m.
KV
-32
FQ
86U
: ap
pro
x. 9
10 x
586
x 5
86
mm
.
Wei
ght:
KV
-28
FQ
86U
: ap
prox
. 45
Kg.
KV
-32
FQ
86U
: ap
prox
. 64
Kg.
Acc
esso
ries
supp
lied:
• 1
Rem
ote
Co
ntro
l (R
M-9
45)
• 2
Bat
terie
s (I
EC
des
ign
ated
,A
A s
ize)
Oth
er fe
atur
es:
•1
00 H
z p
ictu
re,
Dig
ital P
lus.
•T
elet
ext,
Fas
text
, T
OP
text
.•
Nex
TV
iew
.•
Sm
artL
ink.
•T
V s
yste
m a
utod
etec
tion.
•D
olb
y V
irtu
al.
•B
BE
Dig
ital.
•N
ICA
M.
•P
AP
.•
AC
I (A
uto
Ch
ann
el
Inst
alla
tion)
.
Opt
iona
l acc
esso
ries:
•S
tand
esp
ecia
lly d
esig
ned
for t
his
T
V
KV
-28F
Q86
U: S
U-2
8F
Q3.
KV
-32F
Q86
U: S
U-3
2F
Q3.
S
S
Des
ign
and
spec
ifica
tions
are
sub
ject
to c
hang
e w
ithou
t not
ice.
Add
ition
al In
form
atio
n
http
://w
ww
.son
y.ne
t.P
rint
ed in
UK
2-0
67
-79
2-01
2067
7920
1
Lifti
ng th
e T
V S
et
- 13 -
28Tro
uble
shoo
ting
He
re a
re s
ome
sim
ple
solu
tion
s to
pro
ble
ms
whi
ch m
ay a
ffect
the
pict
ure
and
sou
nd.
Pro
blem
No
pic
ture
(sc
reen
is d
ark
) an
d n
o so
und.
Poo
r or n
o p
ictu
re (s
cree
n is
dar
k), b
ut
goo
d so
und
.
No
pic
ture
or
no
me
nu in
form
atio
n
fro
m e
quip
me
nt c
onne
cted
to
the
Sca
rt c
onn
ecto
r.
Go
od p
ictu
re,
no s
ound
.
No
col
our
on
col
our
pro
gra
mm
es.
Whe
n yo
u sw
itch
on
the
TV
the
last
ch
anne
l yo
u w
ere
wa
tchi
ng b
efo
re
switc
hin
g th
e T
V o
ff do
es
not
app
ear.
Dis
tort
ed
pict
ure
whe
n c
han
gin
g p
rog
ram
me
s o
r se
lect
ing
tele
text
.
Wro
ng
char
acte
rs a
ppe
ar w
hen
vi
ewin
g N
exT
Vie
w.
Pic
ture
sla
nte
d.
Sno
wy
pic
ture
whe
n vi
ewin
g a
TV
ch
anne
l.
Sol
utio
n
•C
hec
k th
e ae
rial c
onn
ectio
n.
• P
lug
the
TV
in a
nd
pres
s th
e b
utto
n o
n th
e fr
ont
of
the
TV
.
•If
the
sta
ndby
ind
icat
or
is o
n, p
ress
TV
b
utto
n o
n
the
rem
ote
con
tro
l.
•U
sing
the
me
nu s
yste
m, s
ele
ct th
e “P
ictu
re A
dju
stm
ent”
men
u a
nd s
ele
ct
“Res
et”
to r
etur
n to
the
fact
ory
setti
ngs
(see
pa
ge 1
1).
•C
hec
k th
at t
he o
ptio
nal e
qui
pm
ent i
s on
and
pre
ss t
he
bu
tton
r
epea
ted
ly o
n th
e re
mo
te c
ontr
ol u
ntil
the
corr
ect
inpu
t sym
bol i
s
disp
laye
d o
n th
e sc
reen
(se
e pa
ge
23).
Pre
ss th
e
+ b
utto
n o
n th
e re
mot
e co
ntro
l.
Ch
eck
that
“T
V S
pea
kers
” is
“O
n” in
the
“So
und
Ad
just
men
t”
men
u(s
ee
pag
e 13
).
Ch
eck
that
hea
dpho
nes
are
not
con
nect
ed.
• U
sing
the
me
nu s
yste
m, s
ele
ct th
e “P
ictu
re A
dju
stm
ent”
men
u a
nd s
ele
ct
“Res
et”
to r
etur
n to
fac
tory
set
tings
(se
e pa
ge 1
1).
•T
his
is n
ot a
mal
fun
ctio
n. P
ress
the
num
ber
butto
ns o
n th
e re
mot
e co
ntr
ol
to s
elec
t th
e d
esire
d ch
anne
l.
•T
urn
off
any
equ
ipm
ent
con
nect
ed to
the
Sca
rt c
onn
ect
or o
n th
e re
ar o
f the
T
V.
• U
se th
e m
enu
syst
em
to e
nter
the
“L
ang
uag
e” m
enu
(see
pag
e 1
6) a
nd
sele
ct th
e sa
me
lan
guag
e th
at N
exT
Vie
w is
bro
adc
ast
in.
•U
sin
g th
e m
enu
sys
tem
, se
lect
the
“P
ictu
re R
ota
tion
” op
tion
in t
he
“Fea
ture
s” m
enu
to
corr
ect
the
pic
ture
sla
nt (
see
pag
e 1
5).
• U
sin
g th
e m
enu
sys
tem
, sel
ect t
he “
Man
ual P
rogr
am
me
Pre
set”
me
nu a
nd
adju
st F
ine
Tu
nin
g (A
FT
) to
ob
tain
bet
ter
pict
ure
rec
eptio
n (s
ee p
age
18).
• U
sin
g th
e m
enu
sys
tem
, se
lect
the
“N
oise
Red
uctio
n” o
ptio
n in
the
“P
ictu
re A
dju
stm
ent
” m
enu
and
sele
ct “
Au
to”
to r
educ
e th
e no
ise
in th
e p
ictu
re (
see
pag
e 1
1).
Add
ition
al In
form
atio
n
cont
inu
ed...
29
GB
Pro
blem
No
unsc
ram
bled
pic
ture
whi
lst
view
ing
an
uns
cra
mbl
ed
chan
nel w
ith
a de
cod
er o
r a
Set
To
p B
ox
conn
ecte
d
thro
ugh
the
Sca
rt c
onn
ecto
r 3
/3
.
v, V
, B a
nd b
bu
ttons
do
not w
ork
in
PA
P m
ode.
Re
mot
e c
ontr
ol d
oes
not
fun
ctio
n.
Th
e st
and
by in
dica
tor
on
the
TV
fla
shes
.S
Sol
utio
n
• U
sing
the
men
u sy
ste
m, s
ele
ct th
e “F
eatu
res”
men
u an
d s
et “
AV
3 O
utp
ut”
to “
TV
” (s
ee p
age
15)
.
• C
heck
tha
t th
e D
ecod
er o
r th
e S
et T
op B
ox is
no
t con
nect
ed
on th
e
sca
rt
2/2
.
• P
AP
na
viga
tion
is o
nly
pos
sibl
e in
TV
mod
e, p
leas
e ch
eck
that
Med
ia
Se
lect
or is
set
to T
V.
• C
heck
tha
t th
e M
edia
Sel
ecto
r o
n th
e re
mot
e co
ntro
l is
set
to t
he d
evic
e yo
u ar
e us
ing
(VC
R, T
V o
r D
VD
).
• If
the
rem
ote
co
ntro
l doe
s n
ot o
pera
te th
e V
CR
or
DV
D e
ven
whe
n th
e M
edi
a S
ele
ctor
ha
s be
en s
et c
orre
ctly
, ent
er t
he n
ece
ssa
ry c
ode
set
as
exp
lain
ed o
n p
age
24.
• R
epla
ce th
e ba
tterie
s.
• C
onta
ct y
our
nea
rest
Son
y se
rvic
e ce
ntr
e.
• If
you
cont
inue
to e
xper
ienc
e pr
oble
ms,
hav
e yo
ur T
V s
ervi
ced
by q
ualif
ied
pers
onne
l.
• N
ever
ope
n th
e ca
sing
you
rsel
f.
Add
ition
al In
form
atio
n
- 14 -
=>
Before completely removing the rear cover disconnect thespeaker connector which is located on the inside of the set.
=> =>
=>
=>
=>
=>
=>
=>
=>
=>=>
SECTION 2 DISASSEMBLY
2-1. Rear Cover Removal
To remove lift the main bracket rear slightly and slide thechassis away from the beznet. Ensure that the interconnectingleads are released from their purse locks to prevent damagebeing caused.
When refitting the chassis ensure that the main bracket islocated in the beznet guide slots before sliding the chassisforwards. Refit the inter-connecting leads in their respectivepurse locks.
2-3. Chassis Removal and Refitting
2-2. Speaker Connector Disconnection
Remove the rear cover fixing screws indicated and pull therear cover backwards away from the set. Take care whenremoving the rear cover not to damage the speaker cable[Disconnect the speaker connector] a speaker is fitted insidethe rear cover.
- 15 -
2-6. D2 Board Removal
To remove the D2 board remove the two screws circled,release the clips circled and ease the board gently away fromthe support bracket.
Screws
Clips
2-7. D Board Removal
To remove the D board first remove the D2 bracket byremoving the two screws circled and releasing the fourclips (two on each side of the bracket). The D board canthen be removed using the same method as the G boardbut with the necessity to remove only one screw from themiddle of the D board.
Screws
Clips
To remove the G Board remove the two screws from themiddle of the board, release the clips circled and ease theboard gently away from the support bracket.
Clips
2-4. Service Position 2-5. G Board Removal
To place the chassis in the service position, insert the mainbracket firmly into the T-slot located on the left corner of thebeznet as indicated (see inset). To gain access to the undersideof the boards follow the instructions on page 17. [Removaland Replacement of the main bracket bottom plates].
- 16 -
How to handle the Anode-Cap
1. To prevent damaging the surface of the anode-cap do not usesharp materials.
2. Do not apply too great a pressure on the rubber, as this may causedamage to the anode connector.
3. A metal fitting called a shatter hook terminal is fitted inside therubber cap.
4. Do not turn the rubber foot over excessively, this may causedamage if the shatter hook sticks out.
Removal of the Anode-Cap
2-8. Picture Tube Removal
WARNING:BEFORE REMOVING
THE ANODE CAP
High voltage remains in the CRT evenafter the power is disconnected. Toavoid electric shock, discharge CRTbefore attempting to remove the anodecap. Short between anode and CRTcoated earth ground strap.
Coated EarthGround Strap
1. Discharge the anode of the CRT and remove the anode cap. 2. Unplug all interconnecting leads from the Deflection yoke, neck
assy, degaussing coils and CRT grounding strap. 3. Remove the C Board from the CRT. 4. Remove the chassis assembly. 5. Loosen the Neck assembly fixing screw and remove. 6. Loosen the Deflection yoke fixing screw and remove. 7. Place the set with the CRT face down on a cushion and remove
the Degaussing Coil holders. 8. Remove the Degaussing Coils. 9. Remove the CRT grounding strap and spring tensioners. 10. Unscrew the four CRT fixing screws [ located on each CRT
corner ] and remove the CRT.[Take care not to handle the CRT by the neck.]
Anode button
a
REMOVAL PROCEDURE.
Turn up one side of the rubber cap inthe direction indicated by the arrow a
1 2 Using a thumb pull up the rubber cap firmly in the direction indicated by the arrow b
3 When one side of the rubber cap is separated from the anode button, the anode-cap can be removed by turning up the rubber cap and pulling it up in the direction of the arrow c
b
b
c
24
6
8
10
5
9
37
1
- 17 -
For
saf
ety
reas
ons,
on
no a
ccou
nt s
houl
d th
e pl
ates
be
rem
oved
and
not r
efitt
ed a
fter s
ervi
cing
.R
EM
OVA
L A
ND
RE
PLA
CE
ME
NT
OF
TH
E M
AIN
-BR
AC
KE
TB
OT
TOM
PLA
TE
S.
(1)
RE
MO
VIN
G T
HE
PLA
TE
S
In th
e ev
ent o
f ser
vici
ng b
eing
req
uire
d to
the
sold
er s
ide
of th
e pr
inte
d w
iring
boa
rds,
the
botto
m p
late
s fit
ted
to th
e m
ain
chas
sis
brac
ket r
equi
re to
be
rem
oved
. Thi
s is
per
form
ed b
ycu
tting
the
gate
s w
ith a
sha
rp w
ire c
utte
r at t
he lo
catio
ns in
dica
ted
by th
e ar
row
s.
Not
e :
The
re a
re 2
pla
tes
fitte
d to
the
mai
n br
acke
t. O
nly
rem
ove
the
nece
ssar
y pl
ate
to g
ain
acce
ss to
the
prin
ted
wiri
ng b
oard
.
(2)
RE
FIT
TIN
G T
HE
PLA
TE
S
Bec
ause
the
plat
es d
iffer
in s
ize
it is
impo
rtan
t tha
t the
cor
rect
pla
tes
are
refit
ted
in th
eir o
rigin
allo
catio
n.
Ple
ase
note
that
the
plat
es n
eed
to b
e ro
tate
d 18
0 de
gree
s fr
om th
eir c
ut p
ositi
on to
allo
w th
eta
bs to
be
fitte
d in
to th
eir c
atch
pos
ition
s.
Tab
Cat
ch
- 18 -
• When complete readjustment is necessary or a new picture tubeis installed, carry out the following adjustments.
• Unless there are specific instructions to the contrary, carry outthese adjustments with the rated power supply.
• Unless there are specific instructions to the contrary, set thecontrols and switches to the following settings :
Contrast .................................. normal
Brightness .................................. normal
Preparation :
1. In order to reduce the influence of geomagnetism on the set’spicture tube, face it in an easterly or westerly direction.
2. Switch on the TV set’s power and degauss with a degausser.
(1) Adjustment of Correction Magnet for Y-Splitting Axis.
1. Input a crosshatch signal from the pattern generator.2. Set the Picture control to minimum and confirm that the
Brightness control is set to normal.3. Position the neck assembly as indicated in Fig.3-2.4. Loosen the deflection yoke fixing screw.5. Move the deflection yoke as far forward as is possible.6. Adjust the upper and lower pin symmetrically by opening or
closing the Y-splitting axis correction magnets located on theneck assembly. [See Fig 3-3]
7. Return the deflection yoke to its original position and re-tightenits fixing screw.
Carry out the adjustments in the following order :3-1. Beam Landing.3-2. Convergence.3-3. Focus.3-4. White Balance.
Note : Test equipment required.1. Color bar/pattern generator.2. Degausser.3. Oscilloscope.4. Digital multimeter.
Fig.3-1
(2) Landing
Note : Before carrying out the following adjustments adjust themagnets as indicated [See Fig.3-4].
1. Input a crosshatch signal from the signal generator.2. Rough-adjust the focus and horizontal convergence.3. Switch from the crosshatch pattern to an all-red pattern.4. Move the deflection yoke backwards and adjust with the purity
magnet so that the red is at the centre and it alignssymmetrically [See Fig.3-5].
5. Move the deflection yoke forward to the point where the entirescreen just becomes red [Mark its position].
6. Move the deflection yoke further forward until the screen justchanges colour at the edges. [Mark its position]
7. Position the deflection yoke between the two marks indicatedabove.
8. Input a crosshatch pattern from the pattern generator and rotatethe deflection yoke so that the horizontal lines are parallel withthe top and bottom of the screen.
9. When the position of the deflection yoke has been determined,fasten it with its fixing screw.
10. Switch the pattern generator to green then blue and confirm thepurity.
11. If the beam does not land correctly in all the corners of thescreen, use disk magnets to correct it. [Confirm the cornerlanding forgreen and blue]
Caution :
High voltages are present on the Deflection yoke terminals - take carewhen handling the Deflection yoke whilst carrying outadjustments.
Y-splitting axis correction magnet
Fig.3-3
Fig.3-2 Neck assy
Align the edgeof the neck assy withthe edge of the G2 grid on the G3 side.
G2
G1
G3
+
SECTION 3 SET-UP ADJUSTMENTS
3-1. Beam Landing
- 19 -
Center dot
R G B
R
G
B
C Board
RV7330 (H STAT)H STAT Convergence(on mount side)
H STATconvergence
control
V.STAT Vertical Static Magnet
Fig.3-5
Purity magnets
Align pips oneach magnet
Fig.3-4
Align both Puritymagnets to the verticalposition
Purity control correctsthis area
Disk magnets orrotatable diskmagnets correctthese areas (a-d)
Deflection yoke positioningcorrects these areas
a
c d
b
Disk Magnets
Purity control magnets
GREEN
BLUERED
(1) Screen centre convergence [Static convergence]
1. Input a dot pattern signal from the pattern generator.2. Normalize the picture setting.3. [Moving vertically], adjust the V.STAT magnet so that the
vertical red, green and blue dots coincide at the centre of thescreen.
3-2. Convergence
By opening or closing the V.STAT magnet, the red green andblue dots move in the direction indicated below.
Note: Do not adjust the H.STAT by rotating the V.STATmagnets as this can affect the focus setting.
B
G
R
B
G
R
- 20 -
4. Correction for HMC [Horizontal mis-convergence] and VMC[Vertical mis-convergence] by using the BMC [Hexapole]magnet.
a). HMC correction by BMC [Hexapole] magnet and movement ofthe electron beam.
b). VMC correction by BMC [Hexapole] magnet and movement ofthe electron beam.
Adjust the HAMP using HAMPL and HAMPR registers in theDynamic Convergence section of the service menu.
HTIL correction can be performed by adding a THL correctionassembly to the Deflection yoke.
C < D C = D C > D C = DRG
B
C
DC
D
R
G
B
R
GB
R
G
B
VMC correct ion(A) VMC correct ion(B)
THL Correction assy
HAMP Adjustment
HTIL Adjustment
YCH Adjustment
HMC correct ion(A) HMC correct ion(B)
A < B
A = B
R G B
R G B
A > B
A = B
R G B
R G B
TLV Adjustment
H-TRAP Adjustment
The H-TRAP should not be adjusted unless absolutely necessary as itaffects the TLV settings.
+
++ YCH VR
Deflection Yoke
+
++
TLV VR
Deflection Yoke
HTRAP VR
+
++
Deflection Yoke
- 21 -
Y-splitting axis correction magnet
V STAT convergence magnet
BMC (Hexaploe) magnet
Purity magnet
a-d: screen-cornerconvergence defect
a b
c d
a
b
d
Permalloy AssyX-4387-214-1
c
Install the permalloy assemblyfor the area that needs correcting.
Convergence adjustment with permalloy
Focus
Screen
3-3. Focus Adjustment
1. Receive a television broadcast signal.2. Normalize the picture setting.3. Adjust the focus control located on the flyback transformer to
obtain the best focus at the centre of the screen.Bring only the centre area of the screen into focus, the magenta-ring appears on the screen. In this case, adjust the focus tooptimize the screen uniformly.
3-4. Screen (G2), White Balance
[Adjustment in the service mode using the remotecommander]
G2 adjustment
1. Input a dot signal from the pattern generator.2. Set the Picture, Brightness and Colour to minimum.3. Apply 175V DC from an external power supply to the R, G
and B cathodes of the CRT.4. Whilst watching the picture, adjust the G2 control [SCREEN]
located on the flyback transformer to the point just before theflyback return lines disappear.
Layout of each control
Note : If you are unable to adjust the corner convergence properly,this can be corrected with the use of permalloy magnets.
1. Input an all-white signal from the pattern generator.2. Program the Remote Commander for operation in Service Mode.
[ See Page 22 ].3. Enter into the ‘Service Mode’ by pressing ‘AUX/VIDEO’ button
twice and ‘MENU’ on the Service Commander.4. Select ‘Service’ from the on screen menu display and press
‘Right Arrow’.5. The ‘Service’ menu will appear on the screen.[See Page 22]6. Select ‘Picture’ from the on screen menu and press right arrow.7. Select ‘Picture settings’ from the on screen menu and press right
arrow and set the ‘Contrast_Max’ to MAX.8. Select ‘White Balance’ from the on screen menu and press right
arrow.9. The ‘White Balance’ menu will appear on the screen.10. Set the ‘Normal_PAL_RD’ to 465.11. Adjust the ‘Normal_PAL_GD’ and the ‘Normal_PAL_BD’ so
that the white balance becomes optimum.12. Select ‘Picture settings’ from the on screen menu and press right
arrow and set the ‘Contrast_Min’ to MIN.13. Set the ‘Normal_PAL_RC’ to 121.14. Adjust the ‘Normal_PAL_GC’ and the ‘Normal_PAL_BC’ with
the left and right buttons on the commander so that the whitebalance becomes optimum.
15. Press the ‘OK’ button to write the data for each item.
White balance adjustment for TV mode
- 22 -
4-1. Electrical Adjustments
Service adjustments to this model can be performed using thesupplied remote Commander RM-945.
SECTION 4 CIRCUIT ADJUSTMENTS
Programming the Remote Commander forOperation in Service Mode
Setting the TV into Service Mode
1. Program the remote commander for operation in ServiceMode as described above.
2. Turn on the TV main power switch.
3. Press the ‘aux/video’ standby button on the remotecommander twice.‘TT ’ will appear in the upper right corner of the screen.Other status information will also be displayed.
4. Press ‘MENU’ on the remote commander to obtain thefollowing menu on the screen.
5. Move to the corresponding adjustment item using theup or down arrow buttons on the Remote Commander.
6. Press the right arrow button to enter into the required menu item.7. Press the ‘aux/video’ button on the Remote Commander to quit
the Service Mode when all adjustments have been completed.
Note :· After carrying out the service adjustments, to prevent the
customer accessing the ‘Service Menu’ switch the TV setOFF and then ON.
ecivreS
yrtemoeGerutciP
oiduA
:tceleS :metItceleS :uneMsuoiverP
yrtemoeG
tnemtsujdaedomediWstesffoneercS
stesffoycneuqerF
:tceleS :metItceleS :uneMsuoiverP
tnemtsujdaedomediW
noitpircseD )xam,nim( tluafeD eulaVPMAV )721,821-( 53 53
MOOZV )015,0( 652 652SOPV )115,215-( 01- 01-
NILV )721,821-( 0 0RROCSV )0721,821-( 4 4
HTDIWH )552,652-( 36 36PARTV )721,821-( 1 1PMANIP )115,115-( 08- 08-ROCPU )721,821-( 1- 1-
ROCWOL )721,821-( 2- 2-SOPH )006,006-( 01 01ELGNA )115,115-( 1- 1-
WOB )115,115-( 8 8NILH )552,0( 58 48
PARTH )552,0( 831 831RROCSH )552,0( 001 0016ROCPU )721,821-( 1- 1-
6ROCWOL )721,821-( 0 0LABNUNIP )042,042-( 04- 04-
NIPDIM )042,042-( 06- 06-
:tceleS :metItceleS :uneMsuoiverP
erutciP
ecnalabetihWenoTruoloC
sgnitteserutciP
:tceleS :metItceleS :uneMsuoiverP
H40:NOISREVMVN)D62.0v(Y/AB6EA:uneMniaMecivreS
ecivreSngiseD
rorrE
:tceleS :metItceleS H30HFFHFF:OFNIYROTCAF
3. To return the remote commander to normal operation moderepeat step 1. then press 00000. The TV LED should light.The remote commander is now set to normal mode.
1. Press and hold the left Mode Select buttonuntil the VCR and DVD LED’s flash.
2. Press 99999. The TV LED should light.The remote commander is now set toService Mode.
- 23 -
Sub Brightness Adjustment
1. Input a Monoscope pattern.2. Program the Remote Commander for operation in Service Mode.
[ See Page 22 ].3. Press ‘AUX/VIDEO’ ‘AUX/VIDEO’ 13 on the Remote
Commander.4. Adjust the ‘Sub-Brightness’ data so that there is barely a
difference between the 0 IRE and 10 IRE signal levels.
1. Input a video signal that contains a small 100% white area on ablack background.
2. Connect an oscilloscope to Pin 10 of J7330 [C Board].3. Program the Remote Commander for operation in Service Mode.
[ See Page 22 ].4. Adjust the Sub-Contrast
[ Using ‘AUX/VIDEO’ ‘AUX/VIDEO’ ‘11’ ] to obtain a voltage of 114 +0/- 5V.
Sub Contrast Adjustment
sgnitteserutciP
noitpircseD )xam,nim( tluafeD eulaVLAPROLOCBUS )36,0( 13 43
MACESROLOCBUS )36,0( 13 43ITLXAMPHS )13,0( 13 02
KAEPXAMPHS )51,0( 51 21NIMTSARTNOC )36,0( 71 71XAMTSARTNOC )36,0( 95 95DNAPXETHGIRB )115,0( 004 004RETNECTHGIRB )552,652-( 01 04
:tceleS :metItceleS :uneMsuoiverP
oiduA
edomFFOEBBstesffoybloD.V/larutaNEBB
stesffocimanyDEBBstesffoameniCEBB
stnemtsujdalevelrefoowbuSsdlohserhtnoitcetedoiduA
:tceleS :metItceleS :uneMsuoiverP
edomFFOEBB
noitpircseD )xam,nim( tluafeD eulaVFFO_QERF_WS )04,5( 02 02
TESFFO_FFO_1DNAB )69,69-( 0 0TESFFO_FFO_2DNAB )69,69-( 0 0TESFFO_FFO_3DNAB )69,69-( 0 0TESFFO_FFO_4DNAB )69,69-( 0 0TESFFO_FFO_5DNAB )69,69-( 0 0FFO_SSENDUOL_EBB )86,0( 0 0
:tceleS :metItceleS :uneMsuoiverP
ngiseD
eciveDhctiwSVA-9412AXCeciveDdnekcaB-5133PDD
eciveDrossecorPdnuoS-1143PSMeciveDFI-x889ADT
eciveDLLP-xx06AUTeciveDrossecorPoediV-7249PSV
redoceDamorhC-9102AXCretliFbmoCD3-4083DXC
eciveDecnegrevnoCcimanyD-0708AXCeciveDACRF-9249CRF
enignEJP
:tceleS :metItceleS :uneMsuoiverP
rotinomrorrE
)setuniM:sruoH(:EMITGNIKROW 33:28
:sretnuocrorrEPCO:20E 0PVO:30E 0
CNYSVON:40E 0RKI:50E 0
CII:60E 0MVN:70E 0
TORPH:80E 0RENUT:90E 0DNUOS:01E 0STLOV9:11E 0
ETARNACS:21E 0BMOCD3:31E 0DNEKCAB:41E 0
NOCNYD:51E 0EGATLOVHGIH:61E 0
HCTIWSVA:71E 0CEDAMORHC:81E 0
ACRF:91E 0GNEJP:02E 0
CAD:12E 0TORPREKAEPS:42E 0KCITSYROMEM:52E 0
:tceleS :uneMsuoiverP
- 24 -
Test Mode 2 is available by programming the Remote Commander foroperation in Service Mode [ As shown on Page 22 ] then pressing the‘AUX/VIDEO’ button twice, OSD ‘TT’ appears. The functionsdescribed below are available by selecting the two numbers. Torelease ‘Test mode 2’, press 00, or switch the TV set into Stand-bymode.
4-2. TEST MODE 2:
1. Program the Remote Commander for operation in Service Mode.[ See Page 22 ] and enter into the ‘Geometry’ service menu,Wide mode adjustment.
2. Select and adjust each item in order to obtain the optimum image.
Deflection System Adjustment
Sub Colour Adjustment
1. Receive a PAL colour bar signal.2. Connect an oscilloscope to Pin 5 of CN7331 [C Board].3. Program the Remote Commander for operation in Service Mode.
[ See Page 22 ].4. Adjust the ‘Sub Colour’
[ Using ‘AUX/VIDEO’ ‘AUX/VIDEO’ ‘12’ ] so that the Cyan, Magenta and Blue colour bars are of equal levels as indicated
below.
Same Level
B-Out Waveform
V LIN
BOW
V POS
H POS
PIN AMP
V TRAP
UP COR
ANGLE
LOW COR
00 ffoedom'TT'
10 mumixamotlevelerutcipteS
20 muminimotlevelerutcipteS
30 %53otemuloVenohpdaeh/rekaepsteS
40 %05otemuloVenohpdaeh/rekaepsteS
50 %56otemuloVenohpdaeh/rekaepsteS
60 %08otemuloVenohpdaeh/rekaepsteS
70 noedomgniegA
80 noitidnoCgnippihS
11 tnemtsujdaerutcipbuS
21 tnemtsujdaruolocbuS
31 tnemtsujdassenthgirbbuS
51 tsetliocnoitatoR
61 %05levelerutciP
91 elbasid/elbaneedomyrotcaF
12 RKEDAnoitanitseD
22 LBnoitanitseD
42 UnoitanitseD
53 noitcelesledomediW
63 tsetno/ffoMV
34 dnuosAlauDtceleS
44 dnuosBlauDtceleS
54 dnuosonoMtceleS
64 dnuosoeretStceleS
94 nigrivsaMVNteS
35 elbasid/elbanenoitaludomrevOMF
26 elbasid/elbanednabesabmorfMA
37 )47.6/5.6(metsys2K/DnotiewZelbanE
47 )47.6/5.6(metsys3K/DnotiewZelbanE
87 tfelllufecnalaB
97 thgirllufecnalaB
78 tsetsyeklacoL
19 edommooz9:41teS
29 edommooztramSteS
39 edommooz9:61teS
49 edommoozMOOZteS
59 edommooz3:4teS
69 )66XFrof(edommooztramSteS
99 unememiTgnikroWdnarorrEyalpsiD
- 25 -
5-1. BLOCK DIAGRAMS (1)
DYNAMICFOCUST8900
D2 ( )
14
G2
16
FV
1
18
19
12
15
13
HV
17
8
9
7
10
5
6
4
3
11
HV OVERSHOOTPROTECT
Q6808, Q6809
SS RESETQ6804,Q6806
ABLPROTECT
Q6810
8 4SWITCHQ8900
13
7
5
6
1
2 3
PROTECTIONIC
Q6801
16
12
1
9
15
2
Q6802,Q6803
RECT+
V SENSE
F/B
VG(H)
VS
VG(L)
IC6802DRIVER
AC-HOP-VCC1IC6801
COMPARATOR
IC6800IC6803
CONTROL
CATHODEREF
T6800
4
HV-PROT
HPROTCN6803
SMART MODEDEFLECTION
4CN6802
TO G BOARDCN6007
OCP
RECT-
1
3
2
1
2
3
IC6804CONTROLLER
7
5
6
4
2
PH6800PHOTOCOUPLER
1
7
3
4
1
2
DF DRIVE
EPG MODE
AC MONITORNOT
USED
ABL-COMP
TO A BOARDCN6900
TO D BOARDCN8900
CN6801
DYNAMICFOCUSDRIVERQ8901
2
+9V
L6800
DGC
11
+6V
AU (+)
CN6001
AC IN
AC IN
TO F1 BOARDCN6401
G ( )POWER SUPPLY
5
CN6002CHECK
CHECK
1
1
2
3
CN6003
CN6004PFC
PFC
1
3
CN6008MAIN RY
DGC RYTO A BOARD
CN6200
1
2
DGC
DGC
1
3
T6003
2
4
3
1T6101
4
2
9
7
8
10
12
13
14
15
16
17
1
2
3
6
8IC6001
POWER SUPPLYCONTROLLER
1 V SENSE
2 F/B
CT
4 RT
8
9
VC 1
OCP
3
TIMER
7 SS
6
18
16
15
14
12
10
VD
VG
VG (L)
VC 2
VS
VB
PH6001PHOTOCOUPLER
T6002
12
IC6003REGULATOR
TO A BOARDCN6202
1
2
CN6006
AU (+)
+135V
D6004
FOR CHECK
+11V
9
1
3
2
4
T6001
4
2
RECT+
RECT-
CN6007
TO D2 BOARDCN6802
187
Q6006MOSFET
TRANSISTOR USED BYSWITCHING CIRCUIT
Q6007MOSFET
TRANSISTOR USED BYSWITCHING CIRCUIT
1
2
4
3
RECTIFIERD6016
AU (GND)
AU (GND) 3
4
OCP
OVER-CURRENT
PROTECTION& AMPLIFIERQ6005, Q6010
MAIN RECTD6001
RELAYRY6001
RELAYRY6002
RELAYSWITCHQ6003
RELAYSWITCHQ6102
TO PFC
1
2
RECTIFIERD6102
D6012
D6017
D6033
D6032
6
CN6012
TO A BOARDCN6201
D6034
BUFFERAMPLIFIER
Q7320, Q7321
PICTURE TUBE
CN7331R
TO D2 BOARDHV (T6800)
R
G
B
HV
IC7320VIDEO OUT (BLUE)
IC7310VIDEO OUT (GREEN)
8VOC
IC7300VIDEO OUT (RED)
8
9
10
13
5
HEATER
G2RV7330
CN7330
TO D BOARDCN8214
J7330
C ( )R, G, B OUT
3 VIN
1
2
3
4
5
6
9
R REF
G
G REF
B
B REF
IK
TO B BOARDCN3400
BUFFERAMPLIFIER
Q7300, Q7301
8VOC3 VIN
8VOC3 VIN
BUFFERAMPLIFIER
Q7310, Q7311
BUFFERQ7330
IK
IK
IK
5
BUFFERQ7302
BUFFERQ7322
BUFFERQ7312
- 26 -
5-1. BLOCK DIAGRAMS (2)
IC3400BACKEND VIDEO
KEY 2
IR-DATA
LUMISPONDER
EPG MODE
OCP-OVP
OCP-FLAG
MAIN-SW
DG SW
KEY 1
SIRCS
HV PROT
LED
LINE MUTE
AUDIO RESET
AGC DEFEAT
AV LINK
CSEL
N/U
N-RESET
H-DRIVE
DQP DRV
N/U
DQP C COMP
X-RAY
AFC PULSE
H LIN
H LIN DC
MID PIN
V DRV+
26
CN3100
TO A BOARDCN5207
H TRAPPWM3
BUFFERQ5550
1CN3400
AVSM OUT
AUDIO MUTE
V SAW
E/W
H TRAP
V DRV-
ROTATION
DF DRIVE
MID PIN DC
H2SB4
B15
C14
B13
C12
B12
C11
B11
C10
B10
B9
C8
C7
B7
C6
B6
C5
B5
B30
B29
B28
A20
A19
A18
A17
A16
A15
B14
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
62
BACKENDRESET
X3400
28
12
11
60
30
21
18
37
38
20
22
25
31
32
39
BUFFERQ5509
BUFFER AMPQ5505, Q5507
BUFFERQ5500
BUFFERQ5519
BUFFERQ5503
23
17
16
DQP V COMP
H DRIVE
53
52
51
1810
5
4
2
1
80
79
78
77
76
75
68
67
66
65
42
44
43
35
CLK OUT
55
53
50
47
19
20
24
25
26
29
30
31
32
33
IC3300FRCA
11
3
6
10
9
8
7
5
4
2
1
78
X330016
15
PWMEW4
H OUT
EW
VPROT
SAFETY
DFVBL
PWME1
PWM1
VERT-
VERT+
PWMEW3
PWM2
HFL13
HC1
PWM4
XTAL 2
XTAL 1
R OUT
G OUT
B OUT
SENSE OUT
Y0
Y1
Y2
Y3
Y4
Y5
Y6
Y7
H100
V100
AU OUT
AY OUT
AV OUT
Y OUT 0
Y OUT 1
Y OUT 2
Y OUT 3
Y OUT 4
Y OUT 5
Y OUT 6
Y OUT 7
CLK OUT
H OUT
V OUT
YUV0
YUV1
YUV2
YUV3
YUV4
YUV5
YUV6
YUV7
YUV CLK
H SYNC
V SYNC
AV1
BUFFER AMPQ3401, Q3404
BUFFER AMPQ3400, Q3403
BUFFER AMPQ3402, Q3405
BUFFER AMPQ3406, Q3410,
Q3409
VM
1K
B
G
R
3
5
9
2CN3402
TO C BOARDCN7331
TO VM BOARDCN9402
VM-FRCA
X IN
XOUT
50
RESQ
H SYNC
FBL IN 2
R IN 1
B IN 1
G IN 1
FB-M2
R-M2
G-M2
B-M2
23RESET 100
51
53
24
8
23
17
9
10
15
16
21
22
30
31
32
37
38
39
40
41
46
47
48
55
56
57
58
69
70
6
13SCL 3.3V
CV
BS
MA
IN
SC
L 33
SD
A 3
3A
C M
ON
ITO
R
SDA 3.3V
A30
A31
A32
B32
A23
A24
A21
A29
A28
A27
A22
A26
C31
C30
C15
B31
FS1
FS2
RED 1
GREEN 1
BLUE 1
RED 2
GREEN 2
BLUE 2
CVBS MAIN
C MAIN
CVBS SLAVE
C SLAVE
IC3100VSP94
FLB1
FLB2
R1
G1
B1
R2
G2
B2
Y-M
C-M
Y-S
C-S
X3100
YUV0
YUV1
YUV2
YUV3
YUV4
YUV5
YUV7
YUV CLK
YUV6
H SYNC
V SYNC
AV1
RESET 100
C
Y
1 HOP MUTE
AC MONITOR
SCL
CVBS 1
CVBS 2
RESET
656V10/BLANK
V OUT
H OUT
656CLK
656107
656106
656105
656104
656103
656102
656101
656100
SDA
X-IN
X-OUT
FBL_1
FBL_2
R IN 1
G IN 1
B IN 1
R IN 2
G IN 2
B IN 2
CVBS4
CVBS5
CVBS6
CVBS7
80
81
82
90
91
93
100
101
126
124
127
5
6
8
11
12
27
33
34
35
36
37
114
113
112
105
103
102
10
77
78
26
24
23
25
28
IC0001
P2.15
P2.14
P2.11
P2.9
P2.8
P5.3
P5.0
P5.2
P6.6
P6.5
P5.14
P3.13
P3.12
P3.8
P3.7
P3.6
P3.4
P3.3
P2.13
V SYNC
H SYNC
BLANK/RS OUT
R
G
B
A14/RAS
OCP-OVP
BUFFERQ0001
BUFFERQ0003
BUFFERQ0002
40
39
38
30
29
22
18
17
43
48
45
49
46
47
50
67
63
72
62
56
51
66
65
59
71
64
58
57
70
55D(0)
44
45
44
47
50
51
53
48
5
4
7
10
11
42
8
2
19
39
38
37
13
22
34
35
21
18
17
20
26
25
29
31
32
33
30
24
23
16
15
14
12
16
22
24
26
20
13
11
15
21
23
10
19
9
25
8
6
35
36
34
32
31
30
33
2
3
1
43
42
37
44
4
5
41
40
38
29
19
A(16)
A(17)
A(18)
A(19)
LOOM
/WE
IC0005OTP EPROM
92
121
7
6
5
75
74
7AC ON/OFF BUFFER
Q00754 5
XTAL 1
109
108
OCP-FLAG
EPG-MODE
SIRCS
LUMISPONDER
IR DATA
KEY 2
KEY 1
N-RESET
AGC DEFEAT
12C-DISABLE
DGC-SW
MAIN-SW
LINE MUTE
RESET-AUDIO
AUDIO MUTE
HV PROT
LED
AV-LINK
H2S
V2S
FB-M2
R-M2
G-M2
B-M2
A
C
A
C
B
A(15)
A(14)
A(13)
A(12)
A(11)
A(10)
A(9)
A(8)
A(7)
A(6)
A(5)
A(4)
A(3)
A(2)
A(0)
A(1)
A15/CAS
P4.0/A16
P4.1/A17
P4.2/A18
P4.3/A19
XTAL 2
X0001
P2.10
1C0007
+5V
P3.0
P3.1
SCL33
SDA33
AC MONITOR
IC0002
SCL33
SDA33NVM-WP
P3.15
CVBS-MAINCVBS 1A
B
CSSDRAM
D0
D2
D1
D3
D5
D4
D6
D8
D7
D9
D11
D10
D12
D15
D14
UDQM
CLKEN
MEMCLK
/WR
CSROM
LDQM
RD
54
D13
/WD
D(1)
D(2)
D(3)
D(4)
D(5)
D(6)
D(7)
D(8)
D(9)
D(10)
D(11)
D(12)
D(13)
D(14)
D(15)
CSSDRAM
CSSDRAM
D(0)
D(1)
D(2)
D(3)
D(4)
D(5)
D(6)
D(8)
D(9)
D(10)
D(11)
D(12)
D(13)
D(14)
D(15)
IC0003
CS
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
DQ7
DQM
CLK
CKE
DQ0
/CAS
/RAS
BA0/A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A0
A1
BA1/A13
D(7)
D(7)
A(16)
A(17)
A(18)
A(19)
A(15)
A(14)
A(13)
A(12)
A(11)
A(10)
A(9)
A(8)
A(7)
A(6)
A(5)
A(4)
A(3)
A(2)
A(0)
A(1)
A15
A14
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A0
A1
A13
A19
A18
A16
A17
Q0
Q1
Q2
Q3
Q4
Q5
Q6
Q8
Q9
Q10
Q11
Q12
Q13
Q14
Q15 A-1
/E1
/G
Q7
B 2/2 ( )BACKEND/SCANRATE/LVDS/A-INTERFACEB 1/2 ( )BACKEND/SCANRATE/
LVDS/A-INTERFACE
83 P3.9BACKENDRESET
- 27 -
5-1. BLOCK DIAGRAMS (3)
IC3600AUDIO/VIDEO SWITCHRIGHT OUT
RIGHT IN
LEFT OUT
LEFT IN
BLUE IN
MODE
GREEN IN
RED IN
BLANKING
VIDEO OUT
VIDEO IN
RIGHT OUT
RIGHT IN
LEFT OUT
LEFT IN
BLUE IN
MODE
GREEN IN
RED IN
BLANKING
VIDEO OUT
VIDEO IN
RIGHT OUT
RIGHT IN
LEFT OUT
LEFT IN
MODE
C IN
VIDEO OUT
VIDEO IN
C
Y/CVBS
L
R
2
9
11
13
14
15
17
18
19
20
23
24
25
26
27
28
29
30
32
33
34
35
36
37
38
39
40
41
43
45
47
49
51
54
56
58
60
62
64
BUFFERAMP
Q3656
V-OUT-35
BUFFERAMP
Q3657
BUFFERAMP
Q3658
BUFFERAMP
Q2602
BUFFERAMP
Q2603
V-OUT-25
V-OUT-15
SC2-OUT-L
SC2-OUT-R
SPEAKER L
CN3601
CN3602
CN3603
TO H1 BOARDCN2911
AV3
AV2
AV1
V-OUT-15
V-OUT-25
CVBS/Y MAIN
C-MAIN
SCL
SDA
MUTE
MODE 1
MODE 2
MODE 3
SPEAKER-L
SPEAKER-R
L-ANALOG RF
FRONT-L
SC3 IN-L
SC2 IN-L
SC1 IN-L
L-DIGITAL RF
FRONT-R
R-ANALOG RFV-ANALOG RF
V-DIGITAL RF
V-IN-1
V-IN-2
V-IN-3
C-IN-3
Y/CVBS-FRONT
C-FRONT
C SLAVE
CVBS/YSLAVE
V-OUT-35
SC3 OUT-L
SC3 OUT-R
SC1 OUT-L
SC1 OUT-R
R-DIGITAL RF
SC2-IN-R
SC3-IN-R
SC1-IN-R
MUTE SWITCHQ2604
9V
AC ON-OFF
V-OUT-2B
V-OUT-3B
V-OUT-1B
SPEAKER R
CVBS DIGITAL RF
CVBS/Y MAIN
C-MAIN
C SLAVE
BLUE 1
CVBS/Y SLAVE
GREEN 1
RED 1
BLK 1 FS1
GREEN 2
BLUE 2
R SPEAKER/HP
L-DIGITAL RF
BLK 2
L SPEAKER/HP
RED 2
R-DIGITAL RF
R-ANALOG RF
AV LINK
L-ANALOG RF
SDA
SCL
CVBS/ANALOG RF 35
33
32
29
26
25
23
22
20
19
17
16
15
14
12
11
10
9
7
6
4
3
1
TO A BOARDCN3002
CN3604
LAST RFAV3 IN R
AV2 OUT
CVBS Y MAIN
C MAIN
SCL
SDA
MUTE
MODE 1
MODE 2
MODE 3
AV2 OUT L/SPKR L
AV2 OUT L/SPKR R
ANALOG RF-L
FRONT L
AV3 IN-L
AV2 IN-L
AV1 IN-L
DIGITAL RF
ANALOG RF-R
FRONT R
AV2 IN R
AV1 IN R
DIGITAL RF
AV1 OUT R
AV3 OUT R
AV3 OUT L
AV3 OUT CVBS
Y SLAVE
C SLAVE
FRONT C
AV3 IN C
FRONT Y
AV3 IN Y
AV2 IN Y
AV1 IN CVBS
DIGITAL RF
ANALOG RF
AV1 OUT L
J ( )AV SCART I/OSWITCHING AND
SOCKETS
1
2
3
6
7
8
11
15
16
19
20
1
2
3
6
7
8
11
15
16
19
20
1
2
3
6
8
15
19
20
1
3
5
8
CN3600
TO J BOARDCN3600
TO A BOARDCN2300
VIDEO
HEADPHONES
R
L
CN2912HP R
CN2911
AUDIO L
AUDIO R
Y/CVBS
C
6
5
8
3
1
J2901
1
2
4
3Y/C
CN2900
H1( )FRONT AV INPUT,HEADPHONE &
CONTROL SWITCHES
2HP R
KEY1
KEY2
S0900 - S0905
1
7
CN82116
V -
TO A BOARDCN3000
V DY
V- DY+
DY ASSY
V- DY-
H DY
H- DY+
H- DY-
3
5
6+200V
T8202
V +
H -
H +
H +
H -
1
3CN8104
V +
V -
CN8203
TO D2 BOARDCN6803
DQP-DRV
+
-
6
5
IC8100 REGULATOR
7
4
+-
1
8
3
4
7
6
1
CN8805MP PARA
E/W
H DRIVE
AFC PULSE
X RAY
+-
2
3
IC8103 COMPARATOR
1
4
+-
7
6
8
36
27
T8100
Q8113
Q8112
MID PIN OUTQ8117
H LINQ8121
+8
TO A BOARDCN3008
D ( )DEFLECTION
+15V
-15V
D8200
2
8
9
10
12
7
D8204
D8203
+135V
VCC
VCC
1
H LIN PARA
3
5
9
Q8100, 8102
H PROTECT
Q8101
+
-
6
5
IC8101 REGULATOR
7
4
+-
1
8
3
2
VCC
Q8118, Q8201,Q8202, Q8127
+
-
2
3
IC8102 REGULATOR
1
4
+-
7
8
5
6
VCC
Q8120
31
27
+8
H OUTQ8116
PIN OUTQ8114
5
4
3
1
27
3
DQP-V-COMP
IC8527DQP
Q8508, Q8509Q8512
QP-
QP+
7
4
CN8206
TO VM BOARDCN9401
2
CN8214
TO C BOARDCN7330
T8101
HD1
HD2
HP1
TO A BOARDCN3001
CN89004
5HEATER
Q8510
POWER
S6400
2
1 5
1
F1 ( )POWER SWITCH,FUSE, SIRCS AND
STAND-BYLED
CN6400
ACIN
TO G BOARDCN6001
STB +5V
1
2
CN6401
CN0981
TO A BOARDCN0002
LED
SIRCSOUT
IC0981REMOTE
CONTROLLEDRECEIVER
F6400
D0983
AC IN
AC IN
- 28 -
5-2. CIRCUIT BOARD LOCATION
5-3. SCHEMATIC DIAGRAMS AND PRINTED WIRING BOARDSNote :• All capacitors are in µF unless otherwise noted.• pF : µµF 50WV or less are not indicated except for
electrolytic types.• Indication of resistance, which does not have one for
rating electrical power, is as follows.
Pitch : 5mmElectrical power rating : 1/4W
• Chip resistors are 1/10W• All resistors are in ohms.
k = 1000 ohms, M = 1000,000 ohms
• : nonflammable resistor.
• : fusible resistor.
• : internal component.
• : panel designation or adjustment for repair.
• All variable and adjustable resistors have characteristic curve B, unless otherwise noted.
• All voltages are in Volts.• Readings are taken with a 10Mohm digital mutimeter.• Readings are taken with a color bar input signal.• Voltage variations may be noted due to normal production
tolerences.
• : B + bus.
• : B - bus.
• : RF signal path.
• : earth - ground.
• : earth - chassis.
Reference Information
RESISTOR RN : METAL FILM
RC : SOLID
FPRD : NON FLAMMABLE CARBON
FUSE : NON FLAMMABLE FUSIBLE
RS : NON FLAMMABLE METAL OXIDE
RB : NON FLAMMABLE CEMENT
RW : NON FLAMMABLE WIREWOUND
: ADJUSTMENT RESISTOR
COIL LF-8L : MICRO INDUCTOR
CAPACITOR TA : TANTALUM
PS : STYROL
PP : POLYPROPYLENE
PT : MYLAR
MPS : METALIZED POLYESTER
MPP : METALIZED POLYPROPYLENE
ALB : BIPOLAR
ALT : HIGH TEMPERATURE
ALR : HIGH RIPPLE
Les composants identifiés par une trame etpar une marque sont d'une importancecritique pour la sécurité. Ne les remplacerque par des pièces de numéro spécifié.specified.
Note :
The components identified by shadingand marked are critical for safety.Replace only with the part numbers specified in the parts list.
Note :
CVM Board
A Board
S1 Board
VM
C
H
D1A
JA2
N
D
A1D2
C
A
5-1. BLOCK DIAGRAMS (4)
VM
7
4
CN9401
QP (+)
QP (-)
4
7
8
2
3
VM
VM
1
QP (+)
QP (+)
QP (-)
QP (-)
VM ( )VELOCITYMODULATION
CN9403
QP-
QP+
VM
NECK ASSYTO D BOARDCN8206
VMBUFFER
Q9413, Q9414
VMAMPLIFIER
Q9401, Q9402
VMAMPLIFIER
Q9403
VMAMPLIFIER
Q9404
VMAMPLIFIER
Q9406
VMAMPLIFIER
Q9405
VMAMPLIFIER
Q9407
VMAMPLIFIER
Q9408
2
CN9402
TO B BOARDCN3402
VMAMPLIFIER
Q9409
VMAMPLIFIER
Q9410
VMOUTPUTQ9411
VMOUTPUTQ9412
VM Board
C Board
A Board
J Board
G Board
F1 Board
D2 Board
D Board
H1 Board
B Board
A ( )AUDIO, DEFLECTION,J INTERFACE, TUNER
REGULATORS,B-INTERFACE
TUNERTU1100
X2000
72
71
SWITCHQ1100
SCL
SCA
FM/AM
OSS
AGC DEFEATFROM B BOARDCONNECTOR
CN2300HP-L-OUT
KEY 1/WOOFER MUTE
KEY 2
HP-R-OUT1
3
IC2300HEADPHONE AMPLIFIER
6
7 24
25
2
3
60
67
IC2000SOUND PROCESSOR
21
27
28
STBYAC
POWER OFFPOWER OFFMUTEQ2501
MUTE CIRCUITQ2200 & Q2300,Q2301& Q2302
LINE MUTE
SWITCHQ2400,Q2401
AUDIO MUTE
RESET AUDIO
930
10
3
5
7
11
IC2400AUDIO AMP WOOFER
IC2500AUDIO AMP
IC2200AUDIO AMP
1
7
1
2
4
REAR-R
REAR-L
WOOFER SP
R
L
J2200
SPEAKERS
CN2400
TO WOOFER
CN2501
TO SPEAKERS
CN6202AU+
AU+
AU-
AU-
1
4
3
1
2
6
7
TO G BOARDCN6012PS2001
AU+
AU-
AC MON CIRCUITQ6230, Q6201,Q6204, Q6205,
Q6207
1
5 7
V D
RV
-
CN3000
TO H1 BOARDCN2912
TO D BOARDCN8104
1
3
VERT+
VERT-SWITCHQ5404
IC5400VERT AMP
V D
RV
+
8
1
5
IC5102H TRAP
HT
RA
P
2
1
4
IC5104AMPLIFIER CN3004
1
3ROTATION COIL
ROT-
ROT+
1
3
7
1
6
2
9
12
5
6
7
1
3
4
5
13
14
2
3
1
2
1
2
3
4
2
1
CN3001
CN3008
CN2301
CN0002
CN6900
CN6200
TO D BOARDCN8805
TO D BOARDCN8203
TO MSBOARD
CN1
TO F1 BOARDCN0981
TO D2 BOARDCN6801
TO G BOARDCN6008
H-DRIVE
AFC PULSE
X-RAY
E/W
PRE-RGB
H-LIN-PARA
MP-PARA
H SYNC
DQP-DRV
DQP-V-COMP
DQP-V-MOD
SDA
SCL
SDA-33
SCL-33
SIRCS
LED
EPG MODE
HOP MUTE
DF DRIVE
HV-PROT
DGC RY
MAIN RY
3.3V
SDA/SCLCONVERTERQ0200, Q0201
Q5204, Q5205,Q5211
Q5202, Q5203,Q5208
OCP/OVPLATCH
Q6202, Q6203
B5
C8
B7
C11
B8
B10
C10
B4
C5
C6
B6
A13
A5
A18
A17
A16
A14
A15
A8
C15
C14
B14
A12
A11
A9
A10OCP-UC
OCP-OVP
MAIN SW
DGC SW
HV PROT
DF DRIVE
HOP MUTE
EPG MODE
LED
SIRCS
AUDIO MUTE
LINE MUTE
RESET AUDIO
KEY 1
KEY 2
DQPVMOD/PJ-G
H SYNC
DQPVCOMP/PJ-B
DQP DRV/PJ-R
MID PIN
HL LINEARITY DC
CN5207
TO B BOARDCN3100
CN3002
50
57
56
51
34
33
19
20
22
23
25
26
29
PS2000
A20
Q0100AV LINK
CONVERTER
AV LINK
AV LINK
ANA-RF-R
ANA-RL-L
R-DTV
L-SPK
L-DTV
R-SPK
TO J BOARDCN3604
- 29 -
~ A Board Location Table (A Side) ~
~ A Board Location Table (B Side) ~
~ A Board Waveforms ~
EDOID 5045D 01-D 1126D 4-K 0052CI 3-H 4026CI 4-M
0022D 3-D 1026D 9-J 2126D 9-J 2015CI 01-I 7026CI 01-J
1022D 3-E 3026D 5-L 3126D 8-L 4015CI 01-H 9026CI 8-J
3015D 01-H 4026D 2-K CI 0045CI 01-E 0126CI 4-K
4045D 11-E 0126D 4-L 0042CI 4-J 2026CI 8-L 2126CI 3-L
EDOID 6025D 7-G 4026D 2-E 0022CI 4-L 7026CI 9-F 0031Q 2-L 1042Q 4-F 2025Q 4-H 4045Q 01-K
0022D 3-L 7025D 6-G 5026D 3-E 0032CI 3-J 9026CI 9-F 1031Q 2-K 0052Q 3-H 3025Q 4-H 1026Q 2-E
1022D 4-J 8025D 6-H 6026D 3-D 0042CI 4-G 0126CI 4-F 0002Q 3-J 1052Q 3-H 4025Q 7-G 2026Q 3-E
2022D 4-J 9025D 7-G 7026D 3-D 0052CI 3-H 1126CI 5-E 0022Q 4-I 2052Q 4-H 5025Q 6-F 3026Q 3-E
0052D 3-H 0125D 6-G 8026D 3-D 2015CI 01-G 2126CI 4-E 1022Q 3-L 3052Q 4-H 6025Q 7-H 4026Q 3-E
0015D 01-G 1125D 6-G 0126D 3-D 4015CI 01-H ROTSISNART 2022Q 3-L 4052Q 4-H 7025Q 6-H 5026Q 2-E
4015D 9-H 4045D 01-K 3126D 8-D 0045CI 01-K 0010Q 6-K 0032Q 4-I 0015Q 01-G 8025Q 7-G 6026Q 2-E
0025D 7-F 5045D 01-L 4126D 4-E 0026CI 5-E 0020Q 7-K 1032Q 4-I 1015Q 01-F 9025Q 6-H 7026Q 2-E
2025D 6-F 1026D 9-F CI 2026CI 8-D 1020Q 7-K 2032Q 4-J 0025Q 6-F 0125Q 6-G 8026Q 3-E
5025D 7-G 3026D 5-D 0002CI 4-K 4026CI 4-E 0011Q 2-M 0042Q 4-F 1025Q 6-F 1125Q 6-G 9026Q 4-E
20us/div 5ms/div
700 mVp-p (V) 56 Vp-p (V)
TP1 TP2
~ A Board Semiconductor Voltage Table ~
~ A Board IC Voltage Table ~
~ A Board Difference Table ~
elbaTegatloVCI elbaTegatloVCI elbaTegatloVCI elbaTegatloVCI elbaTegatloVCI
oNfeR oNniP )V(egatloV oNfeR oNniP )V(egatloV oNfeR oNniP )V(egatloV oNfeR oNniP )V(egatloV oNfeR oNniP )V(egatloV
0022CI
1 5.4
0032CI
6 0 0042CI 21 0.4-
2015CI
2 0 0045CI 7 4.0
2 5.4 7 0
0052CI
2 0 5 5.22026CI
4 3.1
3 5.4 8 5.0 5 9.0 6 5.2 5 7.6
5 5.4
0042CI
1 0 7 0 8 2.27026CI
4 3.1
6 5.4 2 0.4- 8 0 4015CI 1 6.41 5 7.6
7 5.4 3 0.01 9 0
0045CI
1 4.09026CI
4 3.1
0032CI
1 0.4 5 0 01 0 3 3.21- 5 7.6
3 0.4 6 2.31- 11 0 5 02126CI
4 1.5
5 5.0 01 9.3 2015CI 1 1.71 6 7.51 5 0
feR )s()e( )g()b( )d()c( feR )s()e( )g()b( )d()c( feR )s()e( )g()b( )d()c( feR )s()e( )g()b( )d()c( feR )s()e( )g()b( )d()c( feR )s()e( )g()b( )d()c(
0011Q 0 0 5.4 2022Q 0 4.0 0 0052Q 1.0 1.0 6.0 1015Q 8.0 4.1 8.6 8025Q 0 0 5.1 2026Q 4.3 4.3 0
0031Q 7.2 1.2 4.8 0032Q 0 0 7.0 1052Q 0 6.0 0 0025Q 8.6 3.6 0.3 9025Q 0 0 5.1 3026Q 0 0 4.3
1031Q 1.2 1.2 0 1032Q 0 4.0 0 2052Q 0 0 0.5 1025Q 0 4.0 0.3 0125Q 0 0 5.1 4026Q 4.3 4.3 0
0002Q 0 0 7.4 2032Q 0 4.0 0 3052Q 0 0 0.5 3025Q 0 4.0 0.3 1125Q 0 0 5.1 5026Q 5.3 7.2 4.3
0022Q 0 0 6.1- 0042Q 9.3 4.3 0 4052Q 0.5 0.5 0 5025Q 0 4.0 5.1 4045Q 0 1.21 0 6026Q 5.1 0.2 7.2
1022Q 0 4.0 0 1042Q 0 0 7.4 0015Q 4.2 8.1 0 7025Q 0 4.0 0.3 1026Q 5.1 6.0 4.3 7026Q 0 0 4.3
feR B68QF82-VK E68QF82-VK B68QF23-VK E68QF23-VK K68QF23-VK U68QF23-VK
0011UT DNETNORF114FE-FTB
DNETNORF114CE-FTB
DNETNORF114FE-FTB
DNETNORF114CE-FTB
DNETNORF114CE-FTB
DNETNORF116UE-FTB
A B C D E F G H I J K L M N
1
2
3
4
5
6
7
8
9
10
11
- 30 -
~ A Board Schematic Diagram [ Audio, Deflection J Interface ] Page 1/3 ~
AV LINKCONVERTER
0.47 0.47
25V 25V
0.1
35P
TO J BOARD CN3604
AUDIO AMPLIFIER
25V
2W
TP2TP1
B-#SSAE6BAD<ITA>-A..-28/32FQ86
WOOFER
5
TO ROTATION COIL
1K
1K
50V
R AUDIO OUT
L AUDIO OUT
V OUT AMPLIFIER
V TRAP/ROTATION ADJUSTMENT
HEADPHONE AMP
LINE OUT AMP2.2k
2.2k
A B C D E F G H I J K L M N
1
2
3
4
5
6
7
8
9
10
11
- 31 -
~ A Board Schematic Diagram [ Tuner, Regulators ] Page 2/3 ~
COMPONENTS MARKED AS XX ARE NOT FITTED ON THIS MODEL
xx
TAB(CONTACT)
18K 10K
22K 150K
10016V 10UH
F1101
1.8 VOLTREGULATOR
xx
B-#SSAE6BAD<ITA>-A..-28/32FQ86
33PF
*
A B C D E F G H I J K L M N
1
2
3
4
5
6
7
8
9
10
11
- 32 -
~ A Board Schematic Diagram [ B Interface ] Page 3/3 ~
xx
+
+
+
00 0
SCL CONVERTER
SCL CONVERTER
B-#SSAE6BAD<ITA>-A..-28/32FQ86
1.5K 1.5K 1.5K
100
A B C D E F G H I J K L M N
1
2
3
4
5
6
7
8
9
10
11
- 35 -
~ B Board Schematic Diagram [ Backend,Scanrate,LVDS,A_Interface ] Page 1/2 ~
xx
xx
xx
xx
35V
XX
SCAN CONVERTER
VIDEO PROCESSING
BACKEND
B-#SSAE6BA<ITA>-B..-28/32FQ86
1/2 Backend, Scanrate, LVDS, A_Interface
4.7k
1k
5.6k
6.8k
100k
47k100k
27k
1k
MMDL914T1
4.7k0.1 MSB709-RT1
0
1k
1k 0
10k 0.22
XX
A B C D E F G H I J K L M N
1
2
3
4
5
6
7
8
9
10
11
- 36 -
~ B Board Schematic Diagram [ Backend,Scanrate,LVDS,A_Interface ] Page 2/2 ~
M27V160-100K1-6Y002OTP
470
0.1
MICRO
SDRAM
AC ON/OFF RESET
NVM
RESET
B-#SSAE6BA<ITA>-B..-28/32FQ86
XX
1k
M24C32WMN6T(A)
UDZS-3.6B
2.2K
K4S281623D-UC75T
2/2
A B C D E F G H I J K L M N
1
2
3
4
5
6
7
8
9
10
11
- 38 -
~ D2 Board Schematic Diagram [ Smart Mode Deflection ] ~
SWITCH
DTZ-5.1B
XX
47K
35V
0.33
U
DYNAMIC FOCUS DRIVER
PROTECTION IC
B-#SSAE6BA<ITA>-D2.-28/32FQ86
NX-6020//Z
0.1
** * *
*
10K
A B C D E F G H I J K L M N
1
2
3
4
5
6
7
8
9
10
11
- 39 -
~ VM Board Schematic Diagram [ Velocity Modulation ] ~
~ H1 Board Schematic Diagram [ Front AV Input, Headphone and Control Switches ] ~~ F1 Board Schematic Diagram [ Power Switch, Fuse, SIRCS and Stand-By LED ] ~
~ VM Board Voltage Table ~
~ VM Board Waveforms ~
feR )s()e( )g()b( )d()c( feR )s()e( )g()b( )d()c(
1049Q 1.5 7.5 9.8 8049Q 3.4 6.3 0
2049Q 4.3 3.4 1.5 9049Q 4.4 1.5 9.8
3049Q 4.4 1.5 9.8 0149Q 3.4 6.3 0
4049Q 3.4 6.3 0 1149Q 3.4 6.3 0
5049Q 4.4 1.5 9.8 2149Q 1.531 6.4.1 5.07
6049Q 3.4 6.3 0 3149Q 3.0 9.0 5.07
7049Q 4.4 1.5 9.8 3149Q 6.6 9.5 4.2
5ms/div 5ms/div 5ms/div
4.2 Vp-p (V) 3.6 Vp-p (V) 2.3 Vp-p (V)
TP2 TP3TP1
250V4700p
E
C6400
XXC0981
25V100
C0982
RD5.6ESB2D0981
XXD0982
1/2WRC
1MR6400
R0981XX
1/4W100R0982
VCCGND
OUT
RPM7240-H5IC0981
50V470p
B
C0983
50V0.01
B
C0984
250V5A
F6400
FH6400
S6400 VD6400
1
2
3
4
BLK4P
CN0981
SIRCS
LED
GND
STBY +5VD09831
1PCN6403
A-Lightning-WIRE
1
3
5
5PCN6401
AC OUT
AC OUT
1
2
2PCN6400
AC IN
AC IN
SPARK GAPS
F1
TO A BOARDCN0002
TO G BOARDCN6001
F1.-28/32FQ86-ITA
TLHK5190
REMOTE CONTROLLED RECEIVER
POWER SWITCH, FUSE, SIRCS& STAND-BY LED
COMPONENTS MARKED AS XX ARENOT FITTED ON THIS MODEL
1/4WFPRD
1R9401
35V47
C9401
25V0.1
C9402
160V10
C9404
500V4700pC9406
16V0.1
C9403
1/10W12k
R9404
1/10W33k
R94051/10W
47R9406 MSD601-RST1
Q9401
MSD601-RST1Q9402
1/10W820
R9402
1/10W680
R9403
1/10W330
R9408
25V0.1
C9407
1/10W47
R9409
1/10W47
R9410
MSD601-RST1Q9403
MSB709-RT1Q9404
1/4WFPRD
10R9411
1/4WFPRD
10R9412
MSB709-RT1Q9406
MSD601-RST1Q9405
1/4WFPRD
10R9413
1/4WFPRD
10R9414
MSB709-RT1Q9408
1/4WFPRD
10R9416
1/4WFPRD
10R9415
MSD601-RST1Q9407
MSD601-RST1Q9409
1/4WFPRD
10R9417
MSB709-RT1Q9410
1/4WFPRD
10R9418
50V10
C9408
160V10
C9409
250VPT
0.1C9410
16V0.1
C9411
2SA2005Q9411
2SC5511Q9412
1/10W22
R9421
1/10W22
R9422
1/10W1k
R9423
1/10W1k
R9420
1/10W33k
R9424
1/10W33k
R9419
1/10W33k
R9426
1/10W33k
R9427
16V0.1
C9413
250VPT
0.1C9412
250VPT
0.47C9414
2WRS
470R9425
1
2
3
4
5
6
7
8
8PCN9403
QP(-)
QP(-)
QP(+)
QP(+)
GND
GND
VM
VM
1uHL9402
1uHL9401
1
2
3
4
5
6
7
WHT7P
CN9401
+B
NC
GND
QP(-)
+9V
NC
QP(+)
XXR9428
MSD601-RST1Q9413
1/10W1k
R94291/10W
100R9430
1
2
3
WHT3P
CN9402
REF
VM
GND1/10W
100R9431
MSB709-RT1Q9414
1/10W470
R9432
1/10W470
R9433
C9415XX
VM
VM.-28/32FQ86
VELOCITY MODULATION
TO D BOARDCN8206
TO B BOARDCN3402
BUFFER
AMPLIFIER
AMPLIFIER AMPLIFIER AMPLIFIERAMPLIFIERAMPLIFIER
AMPLIFIER
AMPLIFIER AMPLIFIER AMPLIFIER
VM OUT
VM OUT
TO NECK ASSY
COMPONENTS MARKED AS XX ARE NOT FITTED ON THIS MODEL
TP1TP3
TP2
RD5.6ESB2D0908
XXD2902
XXD2903
50V1
C2907 50V1
C2906
1/10W470k
R2909
XXD3904
XXD3905
XXC2908
XXC2909
XXC2901
XXC2900
1/10W470k
R2910
1/10W1k
R2917
1/10W1k
R2918
XXR3906
XXR3905
1/10W4.7K
R09110
R0901
1/10W10K
R09134.7K
R0902
CHIP1/10W10K
R0914
XXC2915
XXC2916
R09120
S0900 S0901 S0903S0902 S0904 S0905
5JW0904
XXL0904
5JW2905
5JW2901
XXL2902
XXL2903
1/4W120
R2903
1/4W120
R2902
50V1000pC2931
XXC2903
XXC2902
XXC2930
1/4W120
R2901
50V1000pC2904
XXC2905
1/4W120
R2904
5JW2916
5JW2915
XXL2901
XXL2904
12345678
WHT8P
CN2911
CGN
D
Y/C
VB
S
GN
D
LGN
D
GN
D
R
1 2 3 4 5 6 7
WHT7P
CN2912
KE
Y 1
HP
R
GN
D
GN
D
GN
D
HP
L
KE
Y 2
J2901
XXJW2917
XXJW2918
XXJW2919
XXJW29203
4
12
LR V
S
CN2900
XXJW2921
RD5.6ESB2D0901
H1
CN3600 CN2300TO A BOARD TO J BOARD
COMPONENTS MARKED AS XX ARE NOT FITTED ON THIS MODEL
R A
UD
IO
L A
UD
IO
FRONT AV INPUT, HEADPHONE AND CONTROL SWITCHES
H1.-28/32FQ86-ITA
A B C D E F G H I J K L M N
1
2
3
4
5
6
7
8
9
10
11
- 41 -
~ G Board Schematic Diagram [ Power Supply ] ~
SWITCH
SW MOSFET
SW MOSFET
OVER CURRENTPROTECTION
CONTROL IC
XX
100
2
+
B-#SSAE6BA<ITA>-G..-28/32FQ86
4.7UH
4.7UH
470025V
CN8215
MCZ3001DB
A B C D E F G H I J K L M N
1
2
3
4
5
6
7
8
9
10
11
- 42 -
~ C Board Schematic Diagram [ R-G-B Out ] ~
1 2 9876543
TDA6118JFIC7300
TP
GS
VIN
GN
D
IOM
VD
D
BLS
VO
C
NC
1 2 9876543
TDA6118JFIC7310
TP
GS
VIN
GN
D
IOM
VD
D
BLS
VO
C
NC
1 2 9876543
TDA6118JFIC7320
TP
GS
VIN
GN
D
IOM
VD
D
BLS
VO
C
NC
50V33p
C7323
XXR7305
XXR7315
XXR7325
MSB709-RT1Q7330
1
2
3
4
5
6
7
8
9
BLK9P
CN7331
R
R REF
G
G REF
B
B REF
GND
+9V
IK
35V47
C7332
RD3.6ESB1D7330
1/10W4.7k
R7330
9V
35V47
C7331
1uHL7331
BF550Q7310
AMP MSD601-RST1Q7311
BUFFER
220R7314
1/10W1/10W220
R7313
9V
1/10W270
R7312
1/10W220
R7311
BF550Q7320
AMP
1/10W270
R7322
9V
1/10W220
R7323
MSD601-RST1Q7321
BUFFER
1/10W220
R7321
1/10W220
R7301
CHIP270
R7302
MSD601-RST1Q7301
BUFFER
CHIP220
R7303
9V
BF550Q7300
AMP
220R7324
1/10W
CHIP220
R7304
250V0.1
C7300
250V0.1
C7310
250V0.1
C7320
XXC7301
XXC7311
250V10
C7321
0R7306
0R7316
CHIP0
R7326
100R7307
1/2WRC
220R7308
1SS83TAD7300
1SS83TAD7301
3
4
5
67 8 9
10
11
13
1
GND
GND
1
J7330
1SS83TAD7310
1/4W100
R73171SS83TA
D7311
1/2W220
R7318
1SS83TAD7321
1SS83TAD7320
1/2W220
R7328
1/4W100
R7327
250V2.2
C7334
1/4W1k
R7334
1
1PCN7333
1
1PCN7332
1
2
3
4
5
WHT5P
CN7330
+200V
NC
GND
NC
HEATER
1/2W100R7337
1/4W1M
R7331
1SS83TAD7331
250V2200pC7335
1/2WRC
47R7335
1/2WRC
100R7336
250V10
C7333
1/4W1k
R7333
1uHL7330
110MRV7330
1APS7332
XXR73322kV
4700p
E
C7336
25V0.1
C7302
25V0.1
F
C7312
25V0.1
C7322
XXR7309
XXC7305
R73402.7k
1/10W
XXC7304
2SA1091-0Q7302
BUFFER
1SS133D7302
25V1000pC7306
1/10W1k
R7300
IK
1SS133D7312
25V1000pC7316
IK
1/10W1k
R7310
2SA1091-0Q7312
BUFFER
XXR7319
2.7kR7350
XXC7315
XXC7314
XXR7329
2.7kR7360
1/10W
XXC7325
XXC7324
50V100p
C7330
IK
IK
1/10W1k
R7320
2SA1091-0Q7322
BUFFER
25V1000pC7326
1SS133D7322
50V33p
CH
C7303
50V33p
C7313
XXR7339
XXC7307
CHIP0
JR7303 D73031SS83
XXR7349
CHIP0
JR7313
XXC7317
D73131SS83
XXR7359
XXC7327
CHIP0
JR7323 D73231SS83
XXL7300
XXL7310
XXL7320
12.5JW7332
CV KR G1 G4HV
H
KG KB G2
FV FOCUSRED VIDEO OUT
GREEN VIDEO OUT
BLUE VIDEO OUT
C..-28/32FQ86
C
V901
PICTURETUBE
G
B
R
TO D BOARD CN8214
B
G
R
TO B BOARD CN3400
R,G,B OUT
COMPONENTS MARKED AS XX ARE NOT FITTED ON THIS MODEL
TO D2 BOARD HV(T6800)
KV-32FQ86 - W76LLZ060X
TP4
TP6 TP5
TP1
TP7
TP3
TP2
KV-28FQ86 - W66LLX060X
1kR7361
UDZS-15BD7324
UDZS-15BD7314
UDZS-15BD7304
A B C D E F G H I J K L M N
1
2
3
4
5
6
7
8
9
10
11
- 44 -
~ J Board Schematic Diagram [ AV Scart I/O Switching and Sockets ] ~
25V0.022
C2604
1/10W470k
R2608
C2610
35V47
D2600UDZS-TE17-9.1B
R2600330
1/10W
R2604220
1/10W
XXC2601 D2601
UDZS-TE17-9.1B50V1000pC2605
1/10W470k
R2609R2601
1/10W1k
D2602UDZS-TE17-9.1B
25V0.022C2606 R2606
2201/10W
C2611
35V47
1/10W470k
R2610R2602
CHIP330
C2626
35V47
R2628
CHIP0
1/10W470k
R2632 D2604UDZS-TE17-9.1B25V
0.022C2620R2624
CHIP330
D2606UDZS-TE17-9.1B
R2626330
1/10W
R2630
CHIP0
1/10W470k
R2634 C2627
35V47
25V0.022C2622
1/10W470k
R2646R2638
CHIP330 D2610
UDZS-TE17-9.1B25V0.022C2634 R2642
2201/10W
R2640220
1/10W25V0.022C2632 D2608
UDZS-TE17-9.1BCHIP470k
R2644R2636
CHIP330
XXC2603
1/10W470k
R2611 D2603UDZS-TE17-9.1B
R2603
1/10W1k
50V1000pC2607
XXC2617
1/10W470k
R2633R2625
1/10W1k
50V1000pC2621
D2605UDZS-TE17-9.1B
R2627
1/10W1k
1/10W470k
R2635D2607
UDZS-TE17-9.1B50V1000pC2623
XXC2619
XXC2629 R2637
1/10W1k
50V1000pC2633
CHIP470k
R2645 D2609UDZS-TE17-9.1B
D2611UDZS-TE17-9.1B
50V1000pC2635
1/10W470k
R2647XX
C2631 R2639
1/10W1k
75R3600
1/10W
D3602UDZS-TE17-9.1B100
R3607
1/10W XXC3600
D3607XX XX
C3604100
R3614
1/10W75
R3613
1/10W
D3603XX XX
C3601100
R3608
1/10W75
R3601
1/10W
D3610XX75
R3615
1/10WXX
C3605100
R3621
1/10W
XXC3602
100R3609
1/10W75
R3602
1/10W
D3604XX
100R3622
1/10WXX
C3606D3611XX75
R3616
1/10W
75R3603
1/10W
D3605XX100
R3610
1/10W XXC3603
D3612XX75
R3617
1/10WXX
C3607100
R3623
1/10W
75R3604
1/10W UDZS-TE17-9.1BD3606
100R3612
1/10W
100R3625
1/10WD3613
XX75R3618
1/10W
75R3629
1/10W
D3619XX100
R3635
1/10W
D3601XX75
R3611
1/10W
D3609XX
75R3624
1/10W
UDZS-TE17-9.1BD3615
75R3634
1/10W
10V1
C2636
10V1
C2608
10V1
C2609
10V1
C2624
10V1
C2625
C2639
35V47
C2638
35V47
10V1
C2637
D3600XX
1/10W100
R3605XX
R3606
1/10W100
R3619
XXR3620
D3608XX
XXR3633 D3614
UDZSTE-1713B1/10W100
R3630
C0800XX
1/10W100
R0802D0800
XX
1/10W75
R3628
1/10W100
R3636 D3618XX
1/10W75
R3626UDZS-TE17-9.1B
D3616
1/10W100
R3631
1/10W75
R3627
1/10W100
R3632UDZS-TE17-9.1B
D3617
C2640XX
C2642XX
D2612XX
C2641XX
C2643XX
D2613XX
16V0.1
C3623
0.1C3621
25V0.1
C3622
1/10W68k
R3641
10C2659
50V
35V47
C3610
0.1C3624
25V0.1
C3634
F
16V0.1
C3620
0R3647
CHIP
25V0.1
C2658
SDA
16V0.1
C3608
10V1
C2655
10V1C2656
25V0.1
C3632
1/10W100
R0801
25V0.1
C3626
XXR3646
1/10W100
R0800
9V
10C3627 50V
1/10W39k
R3643
25V0.1
C3616
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
20
21
22
23
24
25
26
27
28
29
30
31
32
33343536373839404142434445464748495051
52
53
54
55
56
57
58
59
60
61
62
63
64
IC3600CXA2149AQ-TL
AV SWITCH
RE
XT
LAS
T R
FR
GD
4
RG
D3
LDO
RG
D2
RG
D1
LD1
AV
2 O
UT
CV
BS
TR
AP
1
Y_M
AIN
VC
C
C_M
AIN
SC
L
SD
A
AD
R
MU
TE
MO
DE
1
MO
DE
2 MODE3
AVCC
ABIAS
AV2 OUT L/SPEAKER L
AV2 OUT R/SPEAKER R
ANALOG RF L
FRONT L
AV3 IN L
AV2 IN L
AV1 IN L
DIGITAL RF LAGND
ANALOG RF R
FR
ON
T R
AV
3 IN
R
AV
2 IN
R
AV
1 IN
R
DIG
ITA
L R
F R
AV
1 O
UT
R
AV
1 O
UT
L
AV
3 O
UT
R
AV
3 O
UT
L
DG
ND
AV
3 O
UT
CV
BS
DV
CC
Y S
LAV
E
TR
AP
2
C S
LAV
E
GN
D
FR
ON
T CG
ND
AV
3 IN
C
AV2 IN CTRAP3
FRONT Y
VBIAS
AV3 IN Y
VGND
AV2 IN Y
VCC
AV1 IN CVBS
TC1
DIGITAL RF
TC2ANALOG RF1/10W
68kR3639
9V
SCL
16V0.1
C3625
L36111uH
Q2604MSD601-RST1
SWITCHR2650
1/10W22k
R2648
1/10W1k
9V
L36121uH
Q2602MSD601-RST1
BUFFER
R2612
1/10W220
R2617
1/10W1k
R2621
1/10W22k
R2620
1/10W22k
C2615
25V0.1
Q2603MSD601-RST1
BUFFER
R2622
1/10W22k
R2613
1/10W220
R2619
CHIP1k
R2623
1/10W22k
16V0.1C3619
16V0.1C3618
16V0.1C3617
16V0.1
C3609
C2614
25V0.1
R2649
1/10W22k
C2657
50V47p
SCL
SDA
AC-ON/OFF
AC-ON/OFF
9V
35V47
C2660
L26021uH
21PCN3601
1RIGHT OUT2RIGHT IN
3LEFT OUT4GND
5GND
6LEFT IN
7BLUE IN
8MODE
9GND
10NC
11GREEN IN
12NC
13GND
14GND
15RED IN
16BLANKING
17GND
18GND
19VIDEO OUT
20VIDEO IN
21GND
21PCN3602
1RIGHT OUT
2RIGHT IN
3LEFT OUT
4GND
5GND
6LEFT IN
7BLUE IN
8MODE
9GND
10
AV LINK
11
GREEN IN
12
NC
13
GND
14
GND
15
RED IN
16
BLANKING
17
GND
18
GND
19
VIDEO OUT
20
VIDEO IN
21
GND
21PCN3603
1RIGHT OUT
2RIGHT IN
3LEFT OUT
4GND
5GND
6LEFT IN
7NC
8MODE
9GND
10
NC
11
NC
12
NC
13
GND
14
GND
15
C IN
16
NC
17
GND
18
GND
19
VIDEO OUT
20
VIDEO IN
21
GND
C3614XX
C3628XX
9VC3641
25V0.1
C3636
35V47
9V-AUDIO
9V-AUDIO
1
2
3
4
5
6
7
8
RED8P
CN3600
C
GND
Y/CVBS
GND
L
GND
GND
R
6.3V1
C2612
6.3V1
C2613
1/10W
R36521k
F
C36420.1
1/10W
R36561k
F
C36430.1
F
C36440.1
1/10W
R36591k
35V
C364547
9V
MSD601-RST1Q3656
BUFFER
MSD601-RST1Q3657
BUFFER
MSD601-RST1Q3658
BUFFER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
35PCN3604
WHT
CVBS DIGITAL RF
GND1
CVBS/Y MAIN
C MAIN
GND 2
CVBS/Y SLAVE
C SLAVE
GND 3
BLUE 1
GREEN 1
RED 1
FS 1
GND 4
GREEN 2
BLUE2
BLK2
RED 2
GND5
L DIGITAL RF
R SPEAKER/HP
GND6
L SPEAKER/HP
R DIGITAL RF
GND7
L ANALOG RF
R ANALOG RF
9VA
GND8
AV LINK
AC-ON/OFF
GND
SDA
SCL
GND9
CVBS ANALOG RF
XXJR2601
XXJR2602
XXJR2609
XXJR2610
XXJR2603
XXJR2612
XXJR2604
XXJR2611
XXJR2615
XXJR2605
XXJR2614
XXJR2607
XXJR2606 XX
JR2608
XXJR2613
XXJR3608
L3608XX
XXJR3609
XXL3609
XXJR3610
XXL3610
CHIP0JR2617
XXL2601
CHIP0JR2618
XXL2600
R3653
1/10W47k
R3654
1/10W22k
R3657
1/10W47k
R3655
1/10W22k
R3660
1/10W47k
R3658
1/10W22k
C3646
35V47
C3647
35V47
C3648
35V47
C3611XX
C3615XX
C3613XX
C3612XX
C3629XX
C3630XX
R2605
CHIP0
CHIP0
R2607
CHIP0
R2614
CHIP0
R2615
CHIP0
R2616
CHIP0
R2618
0.1C3631
XXFB3608
XXFB3609
XXFB3610
R3661
1/10W3.3k
R3662
1/10W3.3k
UDZS-5.6BD0600
UDZSTE-1713BD3621
UDZS-5.6BD3622
UDZS-TE17-9.1BD3623
UDZS-TE17-9.1BD3624
UDZS-TE17-9.1BD3626
UDZSTE-1713BD3627
UDZSTE-1713BD3628
UDZS-TE17-9.1BD3629
UDZS-TE17-9.1BD3630
UDZS-5.6BD3631
UDZS-TE17-9.1BD3632
UDZS-TE17-9.1BD3633
UDZS-TE17-9.1BD3634
C26
16X
XX
XC
2602
XXC2618
C2628 XX
0JR
2616
0JR2628
UDZS-TE17-9.1BD3635
1/10W100
R3638
1/10W75
R3637
L36141uH
SC2-OUT-R
SC2-OUT-L
SC3-OUT-R
SC3-OUT-L
SC1-IN-R
SC1-IN-L
SC2-IN-R
SC2-IN-L
SC3-IN-L
SC3-IN-R
V-IN-1
V-OUT-3B
C-FRONT
Y/CVBS-FRONT
SC1-OUT-L
MODE3
Y/CVBS-FRONT
C-FRONT
SC
3-O
UT
-L
SC
3-O
UT
-R
SC
1-O
UT
-L
SPEAKER-R
SPEAKER-L
V-O
UT
-2S
SPEAKER-R
SPEAKER-L
SC
2-O
UT
-R
SC
2-O
UT
-L
C-IN-3
V-DIGITALRF
CVBS/YMAIN
C-MAIN
CVBS/YSLAVE
C-SLAVE
BLUE-1
GREEN-1
RED-1
BLK1
GREEN-2
BLUE-2
BLK2
RED-2
AV-LINK
L-DIGITALRF
SPEAKER-L
R-DIGITALRF
R-ANALOGRF
SC
1-IN
-R
SC
2-IN
-R
SC
3-IN
-R
FR
ON
T-R
R-ANALOGRF
SPEAKER-R
SC1-IN-L
SC2-IN-L
SC3-IN-L
FRONT-L
V-ANALOGRF
L-ANALOGRF
L-ANALOGRF
SC1-OUT-R
SC
1-O
UT
-R
MODE3
MO
DE
2
MO
DE
1
V-O
UT
-2B
BLUE-1
FRONT-R
FRONT-L
CVBS/YSLAVE
C-SLAVE
V-OUT-3S
V-OUT-1S
CV
BS
/YM
AIN
C-M
AIN
V-O
UT
-3B
V-O
UT
-2S
V-O
UT
-1S
V-O
UT
-3S
V-IN-2
V-IN-3
V-IN-1
AV-LINK
MODE1
V-OUT-1B
GREEN-1
RED-1
BLUE-2
GREEN-2
RED-2
BLK2
C-IN-3
V-IN-3
V-IN-2
V-ANALOGRF
R-D
IGIT
ALR
F
L-DIGITALRF
MODE2
V-O
UT
-1B
AV1
AV2
J
J..-28/32FQ86
AUDIO R OUT
AUDIO R IN
AUDIO L OUT
AUDIO L IN
B
G
R
VIDEO IN
VIDEO OUT
AUDIO R OUT
AUDIO R IN
AUDIO L OUT
AUDIO L IN
VIDEO IN
VIDEO OUT
VIDEO OUT
VIDEO IN
AUDIO R OUT
AUDIO R IN
AUDIO L OUT
AUDIO L IN
TO A BOARDCN3002
COMPONENTS MARKED AS XX ARE NOT FITTED ON THIS MODEL
TO H1 BOARDCN2911
AV SCART I/O SWITCHING AND SOCKETS
C364910PF
JR36110
FB36110UH
R366347
A B C D E F G H I J K L M N
1
2
3
4
5
6
7
8
9
10
11
- 46 -
~ D Board Schematic Diagram [ Deflection ] ~
H OUT
HLINERAITYMIDPIN OUT
PIN OUT
470K
250V
13P
11P
TP7
TP10TP8
TP9
TP2
TP4
TP3
TP1
TP6
TP5
B-#SSAE6BA<ITA>-D..-28/32FQ86
3350V
0
6.8K
*
8.2K
18
*
*
*
XX
* *
*
*
*
*
*
TO G BOARDCN6005
33
0
3.3K
100K
2.2K
6.8K
1K
- 47 -
5-4. SEMICONDUCTORS
CXA2019AQ-TLCXA2149AQ-TL
1(TOP VIEW)
19
20
32
51 33
64
52
LA6500-FA
LM393DTLM358N
2SA1091-O
8 7 6 5
1 3 42
INGND
OUT
1E31SS133T-771SS83D1NL20UD1NL20U-TRD1NL40-TA2EL1ZERA22-08GP08DFUF4005HZS9.1NB2MTZJ-33BMTZJ-4.7C
CATHODE
ANODE
RD15ES-B2RD39ES-B2RD3.6ES-B2RD5.6ESB2RK14V1
CXD3804R-T6
2SK2036(TE85L)2SA1037AK-T146DTA144EKDTA144EKA-T146DTC144EKAMSB709-RT1MSD601-RST1M1MA152WA-T1UN2111
L7809CV/LSYSTP5NK40Z(033Y)ST2310DHI
BA033TIRF614-005IRF614-037IRF6202SA20052SC5511
B
C E
2SC2688(5)-LK
EC B
2SB734-34
1 23
1PS184-115MM3Z4V7T1MM3Z6V8T1MM3Z9V1ST1MM3Z15VT1MMDL914T1UDZSTE-1713BUDZSTE-1718BUDZSTE-173.9BUDZSTE-175.6BUDZSTE-176.2BUDZSTE-179.1BUDZSTE-17-7.5B
CATHODE
ANODE
BYV98-200-RAS 15/12 CATHODE
ANODE
CA0005ADLA6393DLL
D2S4MF
D4SBS6S1VB40
GS1B460/45
M24C32-WMN6T(A)SN74LV00APWRTDA2822D013TR
8 PIN SOP
1 TOP VIEW
MCZ3001D18
91
10
MSP3411G-QA-B1168 61
60
1
52
44
433527
26
18
10
9
( TOP VIEW )
NJM290M
NJM3404AD-WUPC4558G2
( TOP VIEW )
1 4
8 5
- 48 -
1
20
21 40
41
60
6180
(TOP VIEW)
TLHK5190
CATHODEANODE
REF
ANODECATHODE
UPC1093J-1-T
1 2 3 4 5
PST9143NL
PQ1CG2032FZ
TL1431CZ-AP
VSP9417BC3G
STV9379
71
1 15
TDA7482TDA7269
SE135N-LF4
1 23
1 V OUT SENSE2 COLLECTOR3 GND
- 49 -
FLYBACKGENERATOR
THERMALPROTECTION
2 6 3
5
4
7
1
POWERAMPLIFIER
+
-
3
1
2
+
-REFERENCE
VOLTAGE
5-5. IC BLOCK DIAGRAMS
4 3 2 6 7
1
5
Vsense
RemoteDVLD Internal OFF
Latch
Centre
OscSS
F/B Timer
TSD
OCP
Control
Logic
LevelShift
Sel=34vref 5v15v/8vDriver
Reg. 10v
18 8
14
16
15
10
12
11
9
A BOARD IC5400 STV9379A
G BOARD IC6001 MCZ3001D
A BOARD IC6210 BA033T
- 50 -
DFP60
59
56
57
SBUS Interface
IDENT
A/D
SCART Switching Facilities
A/D
D/A
D/A
D/A
D/A
D/A
D/A
I2C Interface
25
23
65 68 13 45 7 6
48
50
51
47
30
34
31
28
33
37
36
DEMODULATOR
A BOARD IC2000 MSP3411G
15 4 3
8 7 269
G BOARD IC6003 SE135N-LF4
-
-
-
9-927-478-01
Sony CorporationSony UK
Service Promotions Dept.
English04CP7100-1
Printed in U.K.© 2004.03
A new TV Repair Assistance Tool that combines ease of use and powerful PC software tools toallow you to save valuable time during many TV repairs.
The TRACE interface connects to the PC's serial port. It providesconnection to the TV's I2C bus and can be provided with an InfraRedtransmitter (optional).
The interface is powered by a standard 9 V PP3 battery for portableuse, and can also be powered by an external 9V/25mA DC powersupply.
The TRACE software that is supplied with the interface allows you to:
With the optional IR Add-on kit, the following features can be added:
Additional features such as Adjustments and Troubleshooting areavailable in chassis-dependent software modules. Please contact yourlocal Sony Service organisation for the latest information.
•••
Read, restore and compare NVM contents via the I2C busAcknowledge check of all I2C devices in the TV setRead Error Codes (emulation of the Error Reader tool)
Remote Commander emulationUser programmable Functional Check through InfraredFast and documented Test Mode setting of all Sony TV chassis
•••
Partnumbers: TRACE Starter Kit (TRACE interface + software): 9-948-320-70TRACE Software (for users of the I2C Link interface): 9-948-340-80TRACE IR Add-on (IR interface + Remote Commander software): 9-948-320-80
PC requirements: IBM-compatible PC with operating system Windows95, Windows98, or WindowsNT*.
* WindowsNT only supported with TRACE interface
Note: For workshops already using the existing I2C Link parallel port interface (9-948-320-30), this software can be used as well, replacing theTV Data Handling software (9-948-340-50), but Error Reader and IR functions can only be accessed with the TRACE interface.