ko-mag instruction manual _vacuum laminating machine

KO-MAG

( / / )

User s Book

Global Cell Phone Repair Parts & Machines Wholesale Online Store - Xicart.com

1. ---------------------------------------

Safety Regulations

2. ---------------------------------------

Parameters and Specification

3. ---------------------------------------

Features

4. -------------------------------------

Inspection and Alignment

5. ----------------------------------------

Operation Process

6. ----------------------------------------

Debubbling process

7. ----------------------------------------

Maintenance

8. -------------------------------

Relation between Vacuum Degree and Altitude


1.

Safety Regulations

For your safety, please read this handbook carefully to be more familiar

with the application and limitations of the machines and the related

potential risks.

A.

Read the instructions before using the equipment B.

Do not boot the equipment before closing the bin gate

C.

This machine adopts the third grounding method. It is important to

keep the grounding normal. Poor grounding will cause the dangers

towards the machine and user

D.

Electricity Box should not be opened without professional staffs are

present


2.

Parameters AC220V 1500W

Power:

AC110V AC220V

Selective:

20-30

Work Environment: 20-30 , clean and dust-free

Laminating: Flat Type Lamination

40S/2pcs

Production Efficiency:

Heating Method: Constant temperature

7

Applicable Size: Below 7

510*480*380mm

Size of Equipment: 510*480*380mm

66kg

Height of Equipment: About 66kg


3.

Features *

No Modules Needed, No Debubbling Process Needed

*

Press to Boot, Easy Operation

*

Smart Constant Pressure; Automatic Shift to the Lamination and

Debubbling Mode

*

Connect the power supply can be used; built-in vacuum pump and air

compressor;


4.

Inspection and Alignment

1 2

Check that whether the tray is smooth Check that whether there are

some foreign matters on the silicone pad

3 4

IC


Module Alignment Alignment on the silicone (LCD

screen is on the silicone

while IC is beyond the

silicone

5 6

Put into the laminator If the scree is with long flat

cable, put the product on the

external part of the anvil cell

and close the door

7 2

mode2 Open the door in

addition to the bubble machine,

the product put to


5.

Operation Process 1

Screen-Pressing Process Mode 1 No Need Remove Bubble

1.

Check whether the connected power

2.

Switch on the power and press the button to boot the equipment

to check that whether the equipment can operate normally or not.

3. OCA IC

;

Put the LCD with the OCA glue on the cut silicone (please stagger

the silicone away from the IC position of the flat cable)

4. ;

Open the gate and put the tray on the cabinet

5. ;

Close the cabinet gate

6. 1

Switch to the "mode 1" in the control system

7. ;

Press button to boot the equipment

8. 2~6 ;

Wait patiently for 2 to 6 minutes

9. ;

Wait until the two indicator lights off or the vacuum table turns to

the minimal value. Open the cabinet gate and take out the

product

10.

The process completed, check whether the product is normal or

not.


2

Screen-Pressing Process Mode 2 In addition to the bubble machine

usee

1. 1-5

Repeat the above steps 1-5

2. 2

Switch to the "mode 2" in the control system

3. ;

Press button to boot the equipment

4. 40

Wait 40 seconds

5. ;

Wait until the two indicator lights off or the vacuum table turns to

the minimal value. Open the cabinet gate and take out the product

6.

In addition to the bubble machine by pressing the "open" button

7. 0

Wait for the pressure display table is displayed as zero and the

"open" indicator light;

8.

Open the door in addition to the bubble machine, the product put

to

9.

Close and fasten the handle in addition to the bubble machine,

release the "open" button

10. 4-10 6-9

Patiently waiting for 4-10 minutes, then repeat steps 6-9 above, the

product is taken out


7.

Maintenance

Projects

Items

Formwork

Check that whether there are some

foreign matters. If positive, please

clean them

Lamination Guide Pillar and Work

Platform Sideway

Add some lubricating oil to the

guide pillar and sideway regularly

to make sure the movement is

smooth


8.

Relation between Vacuum Degree and Altitude

1

Generally, the design and tested parameters of the vacuum pump are

conducted under the standardized air pressure environment. If the

altitude is changing, the exact performance will also change. The exact

parameters are displayed in Table 1.

Altitude

(m)

Vacuum Degree

(-Mpa) mmHg

0 0.1013 760

200 0.0990 742.7

400 0.0968 726.2

500 0.0957 717.9

1000 0.0902 676.7

1500 0.0846 634.7

2000 0.0790 593.3

505.9 93~95

1057.5 88~90

Examples: Chengdu of Sichuan Altitude 505.9 Vacuum Degree ranges

from 93 to 95, normal

Yulin of Shanxi Altitude 1057.5 Vacuum Degree ranges from 88 to 90,

normal


Debugging of Vacuum Pressure Gage 1 Panasonic

Panasonic Vacuum Pressure Gage Debugging

2 1

DP-100

Only need to press the

value shown in Table 1

Main

displayed in Main

Sub

displayed in Sub

0 /

0 action is needed (no need for operation) to display the present and

reference values.


ko-mag instruction manual _vacuum laminating machine

Documents

anvil cell

size of equipment

process mode

operation process

debubbling process

height of equipment

silicone pad

cut silicone