know how - builders | builders.co.za · 13 general building guidelines mixing concrete by hand...

15
13 General building guidelines Mixing concrete by hand Mixing by hand is hard work; therefore this technique is suitable only for small jobs or those that can be done in easy stages. To produce good concrete by hand you need to work carefully and methodically at a steady pace. Materials and tools Sharp sand and coarse aggregate; water (7–10 litres of mains water per 15-litre bucket of cement); mixing platform; two shovels; two heavy-duty polythene buckets of identical size – about 15 litres capacity (keep one for cement only); bucket or watering can. 1. Set up a mixing platform (e.g. scrap shutter board/hardboard). 2. Measure required bucket proportions of sand and coarse aggregates and tip them into a pile on the platform. 3. Use the cement shovel to fill the cement bucket to the top. Make sure the bucket is properly packed, knock it two or three times as you fill it because the cement fluffs up as it is shovelled. 4. Make a crater in the top of the pile of aggregate and tip in the bucket of cement. 5. Use the aggregate shovel to mix the pile thoroughly, turning it over at least 3 times until it looks the same colour throughout. 6. Make a crater in the top of the mixed pile and gradually pour in about half the water. Turn the pile again, moving dry material from the edge to the middle, until the water is well mixed in. Aim for an even colour and a dryish, crumbly consistency. 7. Continue adding and mixing in water until the pile is smooth and moist and at a consistency were you can ‘cut’ the mix with a spade and the cut holds its shape. 8. Test the consistency by slapping along the top of the pile with the back of the shovel. If water runs out readily it is too wet. Add a small amount of cement and aggregate (in the correct proportions) and mix again until you get it right. Bricklaying: cutting a brick Cutting a brick in half lengthways is tricky, as the brick is likely to fracture away from your marked line. The easiest way is with a brick bolster and club hammer. Steps: 1. Mark the cutting line round the brick, then score along it with the bolster, tapping it gently with a hammer on all four sides. 2. With the brick laid frog down on sand or grass and evenly supported, rest the bolster in the scored line with its handle tilted slightly towards the waste end of the brick. Strike it firmly on all four faces, then strike it hard and it should break cleanly. Building materials KNOW HOW

Upload: ngohanh

Post on 03-Jul-2018

214 views

Category:

Documents


0 download

TRANSCRIPT

13

General building guidelines

Mixing concrete by handMixing by hand is hard work; therefore this technique is suitable only for small jobs or those that can be done in easy stages. To produce good concrete by hand you need to work carefully and methodically at a steady pace.

Materials and toolsSharp sand and coarse aggregate; water (7–10 litres of mains water per 15-litre bucket of cement); mixing platform; two shovels; two heavy-duty polythene buckets of identical size – about 15 litres capacity (keep one for cement only); bucket or watering can.

1. Set up a mixing platform (e.g. scrap shutter board/hardboard).2. Measure required bucket proportions of sand and coarse aggregates and tip them into a pile on the

platform.3. Use the cement shovel to fill the cement bucket to the top. Make sure the bucket is properly packed,

knock it two or three times as you fill it because the cement fluffs up as it is shovelled.4. Make a crater in the top of the pile of aggregate and tip in the bucket of cement.5. Use the aggregate shovel to mix the pile thoroughly, turning it over at least 3 times until it looks the

same colour throughout.6. Make a crater in the top of the mixed pile and gradually pour in about half the water. Turn the pile

again, moving dry material from the edge to the middle, until the water is well mixed in. Aim for an even colour and a dryish, crumbly consistency.

7. Continue adding and mixing in water until the pile is smooth and moist and at a consistency were you can ‘cut’ the mix with a spade and the cut holds its shape.

8. Test the consistency by slapping along the top of the pile with the back of the shovel. If water runs out readily it is too wet. Add a small amount of cement and aggregate (in the correct proportions) and mix again until you get it right.

Bricklaying: cutting a brickCutting a brick in half lengthways is tricky, as the brick is likely to fracture away from your marked line. The easiest way is with a brick bolster and club hammer.

Steps:1. Mark the cutting line round the brick, then score along it with the bolster, tapping it gently with a

hammer on all four sides.

2. With the brick laid frog down on sand or grass and evenly supported, rest the bolster in the scored line with its handle tilted slightly towards the waste end of the brick. Strike it firmly on all four faces, then strike it hard and it should break cleanly.

Building materials

KNOW HOW

Build

ing

ma

teri

als

14 Our sales representatives work with the merchandise department to ensure that we meet your needs.

Cement

GeNeral purpOse CeMeNT• 32.5N

SIZE ART CODE50kg (468138)

all purpOse CeMeNT• 42.5N

SIZE ART CODE50kg (245)

HIGH sTreNGTH CeMeNT• 52.5N

SIZE ART CODE50kg (8326)

reaDY MIX CONCreTeSTRENGTH ART CODE

20MPA (362608)25MPA (370914)

prO plus CeMeNT• 42.5N+• KZN only

SIZE ART CODE50kg (426381)

prO CeMeNT• 32.5N• KZN only

SIZE ART CODE50kg (355686)

pOWerCreTe CeMeNTSIZE ART CODE50kg (386758)

BuIlDCreTe CeMeNT• 32.5N

SIZE ART CODE50kg (370486)

OrIGINal BuIlD• 32.5N• KZN only

SIZE ART CODE50kg (514855)

sureBuIlD CeMeNT• 42.5N

SIZE ART CODE50kg (8053)

OpC CeMeNT• 52.5N

SIZE ART CODE50kg (8047)

eCO BuIlD CeMeNT• 32.5N

SIZE ART CODE50kg (422984)

TECHNICAL SUPPORT LINE

efficient Deliveries

THE PPC BUILDER’S APP

More Value

As a builder, your customers demand a lot from you. That’s why you need a cement company you can rely on. At PPC, we’re always exploring new possibilities and solutions that we can offer our clients so they can do the best job for all their projects. From a unique Builder’s App for smartphones to on-site deliveries and our technical support line, PPC always gives you strength beyond the bag.

TJDR

55590

Call 0800 023 470 and speak to one of our helpful technical experts.

Improved mix ratios make every bag go further.

Calculate quantities and find your nearest seller of PPC

Cement. Download your free App at www.ppc.co.za.

Intelligent deliveries for better building project management.

Our strength, Your vision.

55590PPC-F13210x148.5.indd 1 2013/11/14 2:59 PM

Build

ing

ma

teri

als

16 Conveniently located throughout South Africa.

Boards & edging

CHIpBOarDSIZE ART CODE

16 x 2750 x 1830mm (33399)16 x 1830 x 915mm (33941)

supaWOODSIZE ART CODE

16 x 1830 x 915mm (33405)16 x 2750 x 1830mm (33952)

plYWOOD SIZE COlOuR ART CODE

9 x 2440 x 1220mm Pine (34065)4 x 2440 x 1220mm Pine (30009)6 x 2440 x 1220mm Pine (34032)

HarD BOarD SIZE COlOuR ART CODE

3.2 x 1220 x 1220mm Brown (34128)3.2 x 1220 x 610mm Brown (16170)

3.2 x 2440 x 1220mm Brown (34125)3.2 x 2440 x 1220mm Brown (33984)6.4 x 1220 x 610mm Brown (30012)

eDGING: IMp/pVC SIZE COlOuR ART CODE20mm Black (31931)20mm Royal mahogany (57449)20mm White (31929)20mm Burgundy mahogany (353719)

22 x 2mm Burgundy mahogany (353718)20mm Natural oak (31925)

eDGING: MelaMINeSIZE COlOuR ART CODE20mm Burgundy Mahogany (353544)

peGBOarD SIZE COlOuR ART CODE

3.2 x 2440 x 1220mm Brown (34089)

sOfTBOarD• Untreated

SIZE COlOuR ART CODE10 x 2440 x 1220mm Plain (33971)13 x 2440 x 1220mm Plain (33968)

MelaMINe BOarD SIZE COlOuR ART CODE

16 x 2750 x 1830mm Natural oak (33917)16 x 2750 x 1830mm White (34112)16 x 2750 x 1830mm Burgundy mahogany (165352)16 x 2750 x 1830mm Cambridge cherry (122192)16 x 2750 x 1830mm Vancouver maple (122193)16 x 2750 x 1830mm Winsor cherry (122194)

sHuTTerBOarDSIZE COlOuR ART CODE

18 x 2440 x 1220mm Pine (150745)

Build

ing

ma

teri

als

17If we don’t stock it, we will source it for you!

Shelving

BIsON eDGe sHelVINGSIZE ART CODE

16 x 1830 x 305mm (33831)16 x 1830 x 380mm (33834)16 x 1830 x 455mm (33838)16 x 1830 x 530mm (33841)16 x 1830 x 610mm (33869)16 x 2135 x 305mm (33876)16 x 2135 x 380mm (33878)16 x 2440 x 305mm (33887)16 x 2440 x 456mm (41137)16 x 2440 x 530mm (33891)16 x 2440 x 610mm (33893)16 x 2750 x 305mm (33895)16 x 2750 x 455mm (33899)16 x 2750 x 530mm (33901)16 x 2750 x 610mm (33902)16 x 3050 x 305mm (33905)16 x 3050 x 380mm (33907)16 x 3050 x 455mm (33908)16 x 3050 x 530mm (33910)16 x 3050 x 610mm (33912)

pOsTfOrM WOrK TOp SIZE COlOuR ART CODE

3530 x 600mm Bodensee cherry (42093)3530 x 600mm Harfard cherry (152174)3530 x 600mm Bavarian Beech (42248012)3530 x 600mm Black slate (42249005)3530 x 600mm Classic onyx (42248016)3530 x 600mm Moss granite (42248002)3530 x 600mm Natural oak (42248003)3530 x 600mm Paru (42248001)3530 x 600mm Verster granite (42248004)3530 x 600mm Venza oak (42248005)3530 x 600mm White (42248006)3530 x 900mm Black slate (143660)3530 x 900mm Moss granite (42251003)3530 x 600mm Isis kokino (42161)

laMINaTeD sHelVINGSIZE TYPE ART CODE

1800 x 305mm Pine (34280)1800 x 380mm Pine (34278)1800 x 455mm Pine (34275)1800 x 535mm Pine (34271)1800 x 610mm Pine (34268)2100 x 455mm Pine (34251)2100 x 535mm Pine (34245)2400 x 305mm Pine (34235)2400 x 380mm Pine (34230)2400 x 455mm Pine (34225)2400 x 535mm Pine (34222)2400 x 610mm Pine (34215)2700 x 305mm Pine (34207)2700 x 380mm Pine (34201)2700 x 455mm Pine (34198)

1800 x 610 x 32mm Pine (393897)3000 x 305mm Pine (34189)3000 x 380mm Pine (34185)3000 x 455mm Pine (34183)3000 x 535mm Pine (34141)3000 x 610mm Pine (1570)

salIGNa sHelVINGSIZE TYPE ART CODE

1800 x 305mm Saligna (173777)1800 x 457mm Saligna (173782)1800 x 610mm Saligna (173788)2400 x 305mm Saligna (173795)2400 x 610mm Saligna (173879)

pOsTfOrM JOINerSIZE COlOuR ART CODE

Corner 900 Black (146689001)Corner 900 Brown (146689003)Corner 900 Granite (146689004)Corner 900 White (146689002)

End cap Aluminium (121636)640mm Aluminium (26386)640mm Black (27853001)640mm Aluminium (26393)

WHITe MelaMINe sHelVINGSIZE ART CODE

1830 x 305mm (30022)1830 x 380mm (30024)1830 x 455mm (30026)1830 x 530mm (33381)1830 x 610mm (30028)2750 x 305mm (33389)2750 x 380mm (33390)2750 x 455mm (34106)2750 x 530mm (34100)2750 x 610mm (33395)

Build

ing

ma

teri

als

18 Flexible pricing on significant purchases.

Mouldings & skirtings

Pine moulding

Hardwood moulding

Quadrant Glazing bead

Cleat

Cleat

Cover strip

Cover strip

Half round

Half round

Skirting

Skirting

Weather bar

Quadrant Scotia

HarDWOOD MOulDINGs DESCRIPTION SIZE ART CODE

Sash bead 9mm x 9mm x 2.4m (300388)Cover bead 22mm x 22mm x 2.4m (289857)Cover bead 22mm x 22mm x 3m (289858)Cover strip 44mm x 3.6m (22548)Cover strip 44mm x 9mm x 3.0m (300377)Quadrant 16mm x 3m (300357)

Weather bar 813mm (23085)Cleat 45mm x 15mm x 3.6m (16074)

Skirting 145mm x 3.0m (21066)Half round 32mm x 3.6m (22695)

Skirting 45mm x 3.60m (22860)Quadrant 19mm x 3m (128698)Skirting 19mm x 3m (402440)

Glazing bead 1.8m (21031)Quadrant 16mm x 3.6m (22758)Quadrant 32mm x 3m (22777)

Round 19mm x 3m (22658)Round 19mm x 3.6m (39775)

Cover strip 30mm x 3.0m (22472)

pINe MOulDING DESCRIPTION SIZE ART CODESAP cover strip 40mm x 3.0m (15886)SAP cover strip 40mm x 3.6m (21387)

SAP cleat 44 x 22mm x 3.0m (22155)SAP quadrant 15mm x 3.0m (22277)SAP quadrant 15mm x 3.6m (22301)SAP skirting 70mm x 3.0m (22414)SAP skirting 70mm x 3.6m (22430)SAP skirting 90mm x 3.0m (23057)

SAP quadrant 19mm x 3m (60767)SAP skirting 75mm x 3m (22914)SAP cleat 44mm x 22mm x 3m (22573)

SAP half round 32mm x 3m (22679)SAP scotia 32mm x 3.6m (22813)

SAP skirting 45mm x 3.6m (22849)SAP half round 32mm x 3.0m (22208)

SAP scotia 32mm x 3.0m (22349)SAP scotia 32mm x 3.6m (22355)

SAP skirting 45mm x 3.0m (21340)SAP skirting 45mm x 3.6m (22383)

HarDWOOD DeCOraTIVe MOulDINGsDESCRIPTION SIZE ART CODE

Double sided skirting 63mm x 3m (300395)Double sided skirting 63mm x 3.6m (300397)Single sided skirting 69mm x 3.0m (300403)Single sided skirting 69mm x 3.6m (300405)

pINe DeCOraTIVe MOulDINGDESCRIPTION SIZE ART CODE

Dado rail old cape 22 x 44 x 3m (23085)Pine skirting 22 x 140 x 3m (290965)

SKU4 22 x 140 x 3m (290962)SKU4 22 x 94 x 3m (290960)SKU6 22 x 94 x 3m (290964)

Build

ing

ma

teri

als

19We design and manufacture precision roof trusses.

Timber

TIMBer sapSIZE ART CODE

38mm x 38mm x 3.0m (5621)38mm x 38mm x 3.6m (5564)38mm x 38mm x 4.2m (5476)38mm x 38mm x 4.8m (5396)38mm x 38mm x 5.4m (5325)38mm x 38mm x 6.0m (5238)38mm x 38mm x 6.6m (5190)76mm x 38mm x 3.0m (8824)76mm x 38mm x 3.6m (8841)76mm x 38mm x 4.2m (8854)76mm x 50mm x 3.0m (8894)76mm x 50mm x 3.6m (8909)76mm x 50mm x 4.2m (8921)76mm x 50mm x 4.8m (8934)76mm x 50mm x 5.4m (8948)76mm x 50mm x 6.0m (8962)76mm x 50mm x 6.6m (8972)

par HarDWOODSIZE ART CODE

12mm x 96mm x 1.8m (300440)12mm x 96mm x 3.0m (300442)20mm x 20mm x 1.8m (292)22mm x 44mm x 1.80m (23354)22mm x 69mm x 1.8m (300462)22mm x 69mm x 2.4m (300463)22mm x 69mm x 3.0m (300464)22mm x 96mm x 3.0m (300452)22mm x 144mm x 1.8m (300453)22mm x 144mm x 2.4m (300454)22mm x 144mm x 3.0m (300455)22mm x 222mm x 1.8m (300456)22mm x 222mm x 2.4m (300457)22mm x 222mm x 3.0m (300458)32mm x 10mm x 3.0m (132276)32mm x 32mm x 18m (361)32mm x 32mm x 2.4m (374)32mm x 32mm x 3.0m (381)32mm x 44mm x 1.8m (300472)

sa pINe parSIZE ART CODE

12mm x 96mm x 1.8m (302071)12mm x 96mm x 2.4m (302072)12mm x 96mm x 3.0m (302073)20mm x 20mm x 1.8m (6109)22mm x 22mm x 2.4m (302112)22mm x 22mm x 3.0m (302113)22mm x 44mm x 1.8m (302116)22mm x 44mm x 2.4m (302117)22mm x 69mm x 1.8m (302120)22mm x 69mm x 2.4m (302121)22mm x 69mm x 3.0m (302122)22mm x 96mm x 1.8m (302123)22mm x 96mm x 2.4m (302124)22mm x 96mm x 3.0m (302125)22mm x 144mm x 1.8m (302105)22mm x 144mm x 2.4m (302106)22mm x 144mm x 3.0m (302107)22mm x 222mm x 1.8m (302108)22mm x 222mm x 2.4m (302109)32mm x 32mm x 2.4m (302152)32mm x 32mm x 3.0m (302153)

SIZE ART CODE114mm x 38mm x 3.0m (8697)114mm x 38mm x 3.6m (8712)114mm x 38mm x 4.2m (8727)114mm x 38mm x 4.8m (8742)114mm x 38mm x 5.4m (8753)114mm x 38mm x 6.0m (8770)114mm x 38mm x 6.6m (9141)152mm x 38mm x 3.0m (9008)152mm x 38mm x 3.6m (9132)152mm x 38mm x 4.2m (8784)152mm x 38mm x 6.0m (41201)152mm x 38mm x 6.6m (41709)228mm x 38mm x 6.0m (9424)228mm x 38mm x 3.0m (41711)228mm x 50mm x 6.0m (9490)

SIZE ART CODE32mm x 44mm x 2.4m (300473)32mm x 44mm x 3.0m (300474)

32mm x 144mm x 1.8m (300469)44mm x 10mm x 1.8m (128426)44mm x 10mm x 3.0m (132277)44mm x 20mm x 2.4m (534)44mm x 20mm x 3.0m (591)44mm x 44mm x 1.8m (300487)44mm x 44mm x 2.4m (300488)44mm x 44mm x 3.0m (300489)44mm x 69mm x 1.8m (300490)44mm x 69mm x 2.4m (300491)44mm x 69mm x 3.0m (300492)69mm x 69mm x 2.4m (300500)70mm x 20mm x 2.4m (6506)70mm x 32mm x 1.8m (6443)70mm x 32mm x 2.4m (6438)

140mm x 32mm x 1.8m (6603)

SIZE ART CODE32mm x 69mm x 1.8m (302158)32mm x 69mm x 3.0m (302160)32mm x 44mm x 1.8m (302155)32mm x 44mm x 2.4m (302156)32mm x 44mm x 3.0m (302157)44mm x 10mm x 1.8m (425)44mm x 10mm x 3.0m (502)44mm x 32mm x 1.8m (607)44mm x 32mm x 2.4m (602)44mm x 32mm x 3.0m (603)44mm x 44mm x 1.8m (302176)44mm x 44mm x 2.4m (302177)44mm x 44mm x 2.4m (627)44mm x 44mm x 3.0m (302178)44mm x 69mm x 1.8m (302179)44mm x 69mm x 2.4m (302180)69mm x 69mm x 2.4m (302238)70mm x 10mm x 1.8m (132393)70mm x 32mm x 2.4m (5871)70mm x 32mm x 3.0m (6424)

Build

ing

ma

teri

als

20 We do precision timber & board cutting & edging.

Decking & poles

salIGNa DeCKING• Double-sided

SIZE ART CODE100 x 20 x 1500mm (363962)100 x 20 x 1800mm (363963)100 x 20 x 2100mm (363964)

Balau DeCKING• DIY decking for pools, patios & jacuzzis• Can be installed on a flat hard surface or on soil

SIZE ART CODE19 x 19 x 2400mm (519939)19 x 19 x 2700mm (519940)19 x 19 x 3000mm (519941)

pOles• Round• CCA - treated

SIZE ART CODE75 - 100mm x 1.8m (9672)75 - 100mm x 2.1m (408380)75 - 100mm x 2.7m (408402)75 - 100mm x 2.4m (9676)75 - 100mm x 3.0m (9678)75 - 100mm x 3.6m (9681)75 - 100mm x 4.2m (9682)75 - 100mm x 4.8m (9683)75 - 100mm x 5.4m (9686)

100 - 125mm x 3.0m (408403)100 - 125mm x 3.6m (408404)

Build

ing

ma

teri

als

21Avoid costly mistakes, let us do your quotes & tenders with Intellibuild Estimating.

Building formed

lINTels SIZE ART CODE

105mm x 75mm x 0.90m (10015)105mm x 75mm x 1.20m (10024)105mm x 75mm x 1.50m (10029)105mm x 75mm x 1.80m (10032)105mm x 75mm x 2.10m (10038)105mm x 75mm x 2.40m (10044)105mm x 75mm x 2.70m (10049)105mm x 75mm x 3.00m (10053)105mm x 75mm x 3.30m (10081)105mm x 75mm x 3.60m (10086)105mm x 75mm x 3.90m (10092)105mm x 75mm x 4.20m (10095)105mm x 75mm x 4.50m (10098)105mm x 75mm x 4.80m (10102)105mm x 75mm x 5.10m (10105)105mm x 75mm x 5.40m (10111)105mm x 75mm x 5.70m (10115)105mm x 75mm x 6.00m (10120)105mm x 75mm x 6.60m (10129)

BrICKfOrCeSIZE ART CODE

75mm x 2.8mm x 20m (160)150mm x 2.8mm x 20m (170)225mm x 20m x 2.8mm (234)

Galvanised 75mm x 2.8mm x 20m (463184)Galvanised 150mm x 2.8mm x 20m (463189)

CONCreTe slaBsSIZE ART CODE

IE 455 x 455mm (41021)IE 300 x 300mm (40624)

Concrete paving slabs 455 x 455 x 50mm (40630)

CONCreTe WINDOW sIllsSIZE ART CODE

250mm x 180mm (40632)510mm x 180mm (40631)

plasTIC TerraCOTTa aIr VeNT BrICKSIZE ART CODE

220 x 140 x 18mm (455035)

GreY CONCreTe aIrBrICKSIZE ART CODE

220 x 140 x 18mm (40572)

Build

ing

ma

teri

als

22 Credit facilities available for approved contractors.

Building formed

eVerITe BuIlDING COluMN SIZE ART CODE

9mm x 200mm x 2.0m (7067)9mm x 200mm x 2.5m (7032)9mm x 200mm x 3.0m (6994)9mm x 250mm x 2.0m (6988)9mm x 250mm x 2.5m (6974)9mm x 250mm x 3.0m (6945)9mm x 300mm x 2.0m (6977)9mm x 300mm x 2.5m (6933)9mm x 300mm x 3.0m (6895)

BuIlDING COluMN HeaDerSIZE ART CODE

200mm (151171)250mm (151172)300mm (151173)

BuIlDING COluMN fOOTerSIZE ART CODE

200mm (151174)250mm (151175)300mm (151176)

CONCreTe raINWaTer CHaNNelSIZE TYPE ART CODE

610mm Stop end (40573)700mm Open (10144)

CONCreTe GullY TOpSIZE ART CODE

400 x 400/120mm hole (40622)

Build

ing

ma

teri

als

23We offer gas filling & swapping.

Bricks & mesh

CeMeNT sTOCKMPA ART CODE

7 (127225)14 (380161)10 (391176)

ClaY sTOCK BrICKsquANITY ART CODE

Yard (128652)

plasTer MaXI (ClaY) BrICKsquANITY ART CODE

Each (289815)

plasTer CeMeNT BrICKs• Direct delivery

quANITY ART CODE10000 (7MPA) (169691)12000 (7MPA) (169690)

50MM paVer BeVelCOlOuR ART CODEAutumn (402958)

Charcoal (402955)Grey (402953)Red (402954)Tan (402957)

Glass BrICKsTYPE ART CODEBubble (416056)Flemish (415882)Ocean (416058)Rattan (416307)

sTONequANTITY ART CODE

40kg (8046)13mm 1 ton (414216)19mm 1 ton (414217)13mm yard (127158)19mm yard (127144)

60/80MM paVer INTerlOCKCOlOuR ART CODECharcoal (402960)

Grey (402963)Red (402959)

Build

ing

ma

teri

als

24 We manufacture wooden doors to size in bulk quantities.

Sand, steel, stone & premixes

reINfOrCe MesHref 100/ref 193

SIZE ART CODE6 x 2.4m (4535)60m roll (69851)

preMIX raNGe• Exclusive• 40kg

TYPE ART CODEBuilding mix (515974)Concrete mix (515973)Plaster mix (515975)Screed mix (515976)

supa preMIX• Only available in the Western Cape

TYPE SIZE ART CODEConcrete 25kg (153198)Plaster 25kg (153200)Mortar 12kg (153202)Plaster 12kg (153203)

COlD aspHalT• Exclusive • 25kg• Easy multi-purpose application• No tack coat required

ART CODE(420607)

reINfOrCe sTeel rODsSIZE ART CODE

Y10 6m (4516)Y12 6m (4511)Y8 6m (4506)

saNDTYPE SIZE ART CODE

Building sand 40kg (42052)Building sand Yard sales (127121)Playpen sand 40kg (235698)Plaster sand 40kg (8077)Plaster sand Yard sales (127132)Plaster sand 1 ton (173378)River sand Yard sales (127142)River sand 1 ton (414212)

Build

ing

ma

teri

als

25We offer expert advice, quotations & friendly service before & after sales.

Wheelbarrows & trestles

Trolleys & scaffolding

WHeelBarrOW • Green

TYPE ART CODEFlat pan (10)Concrete pan (13)Concrete polypan (412266)

fOlDING NOse TrOlleYTYPE ART CODE

FNJ junior (1850)F2 FN2 (3066)F1 FN1 (3074)

fOlDING TrOlleY• Folded dimensions:

65mm x 480mm x 700mm • Extended dimensions:

420mm x 480mm x 980mm • Loading weight: 100kg

ART CODE(427764)

pINe TresTle SIZE ART CODE

800mm (26819)

BuIlDers TresTle • 1400mm(h)

x 200mm(w)• Extends to a height

of 2.5m• Safe working load: 450kg

ART CODE(22627)

WHeelBarrOW• Exclusive• Metal strut for additional stability• Solid rubber wheel for durability &

rubber handles for extra grip• Reinforced rim for additional strength

ART CODE(467570)

COKe TrOlleY• 5CCT • Heavy duty: all types of loads • Capacity: 225kg • Height: 1230mm

ART CODE(1810)

(158196)

leVelING JaCK WITH Base

ART CODE(154646)

sCaffOlDINGs TYPE & SIZE ART CODE

Frame 900mm x 1500mm (2041)Tie bar 5 x 3 STTB53 (2050)

Cross brace 5 x 3 STCB53 (2057)Platform 5 x 3 STPLAT53 (2106)Castor 5 x 3 FG150NY (2099)

pOlY WHeelBarrOW• Exclusive

CODE(523434)

23 INCH saWHOrse• Exclusive• 578mm(w) x 1020mm(d) x 792mm(h) • Built-in V-groove • Runner feet for anti-sliding

ART CODE(462381)

Build

ing

ma

teri

als

26 We do building material cost estimation.

Ladders

6 sTep aluMINIuM laDDer• Safe working load: 100kg

DESCRIPTION ART CODEHSL5 (5-step) (30)

HSL6 (43)

3 sTep aluMINIuM laDDer• Safe working load: 100kg

DESCRIPTION ART CODESPL3 (2092)

6 sTep aluMINIuM laDDer• Safe working load: 115kg

DESCRIPTION ART CODEISL6 (221)

ISL8 (8-step) (55103)

8 sTep superlITe fIBreGlass laDDer• Safe working load: 130kg

DESCRIPTION ART CODELFG8 (73)

MulTI-purpOse aluMINIuM laDDer • Exclusive • Safe working load: 130kg• Can be used as a double sided 6 step

A-frame or a 12 step extension ladder

ART CODE(520147)

6 sTep DOMesTIC aluMINIuM laDDer• Exclusive• Safe working load: 115kg

ART CODE(517154)

2 sTep DOMesTIC laDDer• Exclusive• Safe working load: 150kg

TYPE & SIZE ART CODE2 step (421013)

Step stool 3 step (225844)Step stool 4 step (405878)

Handy hint:

Proper selection

Select ladder of proper duty rating to support

combined weight of user and materials. Ladders

are available with duty ratings of 95kg,

100kg, 115kg & 130kg. Inspect thoroughly

for missing or damaged components. Never

use a damaged ladder and never make

temporary repairs. Inspect thoroughly for loose

fasteners. Make sure all working parts are in

good working order, (lubricate if necessary).

Clean ladder of all foreign material (wet paint,

mud, snow, grease, oil, etc.). Destroy ladder if

damaged, worn or exposed to fire or chemicals.

Hang ladder on racks at intervals of 1,8m

for support. Never store materials on ladder.

Never drop or apply an impact load to ladder.

Securely support ladder in transit.

Easy storage & transport

Platform A-Frame

L-Frame Extended

Build

ing

ma

teri

als

27We do timber cutting & planning.

Ladders

leaN TO laDDer • Fibreglass • Safe working load: 115kg

TYPE ART CODE10 step (461146)12 step (461147)14 step (461148)

3-IN-1 aluMINIuM eXTeNsION laDDer • Safe working load: 100kg

TYPE ART CODEAP300 (46756)

aluMINIuM laDDer • Safe working load: 115kg• Can be used as a double sided 6 step

A-frame or a 12 step extension ladder

TYPE ART CODEMP7238 (56)

pusH up seCTION aluMINIuM laDDer • Safe working load: 115kg

TYPE SIZE ART CODEDMS540 5.4m (159288)DMS600 6m (159289)DMS660 6.6m (159290)DMS780 7.8m (159291)DMS900 9m (159292)

6-IN-1 laDDer• Exclusive • 4.2m• Safe working load: 130kg

ART CODE(520146)

superlITe laDDer • Fibreglass• Non-conductive of electricity• Safe working load: 115kg

TYPE ART CODE6 step (405761)8 step (405762)

10 step (412923)