kj-3300 user manual (en) cham cong
DESCRIPTION
KJ-3300 User Manual (en) Cham CongTRANSCRIPT
KJ-3300(L)
USERMANUAL
Ultra Speed Fingerprint Recognition Algorithm
VER. 1.05ENGLISH
www.ekjtech.co.kr
S
1
T S
T S
Keep out of direct sunlight and heat radiation sources.
Shall not be e posed to dripping or splashing and no ob ects filled ith liquids,such as vases, shall be placed on the products.
hen cleaning, do not use liquid solvent or et cloth. ipe ith soft cloth.
Never disassemble or modify this device in any ay.(KJ Tech is not liable for problems caused by unauthori ed modification or attempted repair)
efore using this device, read and follo all instructions for safety.
KJ-3300(L)USER MANUAL ver.1.05www.ekjtech.co.kr
2
T S
T S
efore using this device, read and follo all instructions for safety.
KJ-3300(L)USER MANUAL ver.1.05www.ekjtech.co.kr
Do not install this device near by TV, monitor or magnetic interference.
If the product fails to operate normally, contact the authori ed dealer or service senter.
3
L TE S
L TE S
This system comes ith the follo ing components.
KJ-3300(L)USER MANUAL ver.1.05www.ekjtech.co.kr
KJ-3300(L) racket
IN IN 5 IN IN( o er, 5 C N)
Cable Scre rogram CD
For bracket ea T3 20mmFor KJ-3300(L) 2ea M3 mm
4
TS T EF T S
TS T E F T S
KJ-3300(L)USER MANUAL ver.1.05www.ekjtech.co.kr
LEDLight on for system status.
Fingerprint sensor Used to register or identity the user.
Function Key selects the events for T A, Enter, E it, or navigate The menu.
Speaker utputs sounds effect voice.
Color TFT LCDDisplays time, device status, user list and UI for operation.
Touch adKey button for operation.
USFor US memory.
ConnectorFor cable connection.
5
E S S
E S S
KJ-3300(L)USER MANUAL ver.1.05www.ekjtech.co.kr
:1 5mm
:115mm
:1 . mm
: 2. mm
mm
Front Vie racket racket
Side Vie6
F E T E ST T
F E T E ST T
KJ-3300(L)USER MANUAL ver.1.05www.ekjtech.co.kr
lace the finger on the sensor as seen in belo in the proper
ay.lace the entire area of your
finger firmly to the sensor.ou have to register fingerprint in proper ay to enhance
recognition rate.Recommended to use finger hich has no damage.Recommended to register more than t o fingerprint in case.
roper ay Improper ay.
7
E F T E
E F T E
KJ-3300(L)USER MANUAL ver.1.05www.ekjtech.co.kr
Verification mode can be setup in verification mode (Settings asic Verification Mode)
CARD ID( IN) FD(Finger rint)
KJ-3300 supports various type of access mode : Combination of Fingerprint, Card and ID( IN)
8
F T S E
F T S E
KJ-3300(L)USER MANUAL ver.1.05www.ekjtech.co.kr
Function Key is usually used for Time Attendance.The admin is able to setup a certain definition to a function key in the program(F1 Sing in) The admin is able to find out the users attendance records.
ID Authentication Scheme F1~F 0~
CARD Authentication Scheme F1~F 0~
1. ress Function Key (F1~F ) only or press numbers after Function Key .
2. resent the card to enter.
FD Authentication Scheme F1~F Fingerprint
1. ress Function Key (F1~F ) only or ress numbers after Function Key .
2. lace Finger rint to enter.
1. ress Function Key (F1~F ) only or ress numbers after Function Key .
2. Input ID used to enter.
9
L S STE E T E
L S STE E T E
KJ-3300(L)USER MANUAL ver.1.05www.ekjtech.co.kr
USER
SETTIN
US MEM R
S STEM INF
TEST
1.Enroll 2.Delete 3.Set Temp ID
1. asic 2.Advanced 3.AC Setting .Communication 5.Schedule .Log Setting
1.Do nload eneral Log 2.Do nload All eneral Log 3.Do nload Management Log .Do nload All Management Log 5.Do nload User Info .Upload User Info .Upgrade Firm are
1.Memory 2.Device Info 3.Advanced
1.Test All 2.Test Memory 3.Test LCD .Test Sound (AUT ) 5.Test Sound (MANUAL).Test Sensor .Test Keyboard .Test RTC .Test Case Status 10.Test Card Reader
10
L S STE T EE ST T E
L S STE T EE ST T E
KJ-3300(L)USER MANUAL ver.1.05www.ekjtech.co.kr
SETTIN 1. asic 2.Advanced 3.AC Setting .Communication 5.Schedule .Log Setting
asic
1.Time
2.Date
3.Date Format
.Language
5.Use usytone detection
. Set hone Numbers
Advanced
1.Vertification Mode
2.ID Mask
3.Use Tamer Alram
.Use Touch Sensor
5.Celibrate Senseor
.Restore Factory Settings
.Clear eneral Log
.Clear Management Log
.Clear Enroll Date
AC Settings
1.Define Time one
2.User Time one
3.Lock Type
.Lock Door Release Time
5.Door pen arning
.Re-access Count
.Re-access Limit Time
. iegand Format
.Anti- assback
11
L S STE T EE ST T E
L S STE T EE ST T E
KJ-3300(L)USER MANUAL ver.1.05www.ekjtech.co.kr
SETTIN 1. asic 2.Advanced 3.AC Setting .Communication 5.Schedule .Log Setting
Communication
1.Device ID
2. audrate
3.TC I Settings-D C-I Antipass-Subnet Mask-Default ate ay- ort-Mac Address
.Communication ass ord
Schedule
1.Set Tmode
2.Ring Settings
3.Auto Door
.Auto Funckey
5.None-Relat Funckey
.Day Light
. oliday
.Funckey Alarm
.Idle Settings
Log Setting
1.Management Log arning
2. eneral Log arning
12
S
13
S L S
S L S
KJ-3300(L)USER MANUAL ver.1.05www.ekjtech.co.kr
These displays are primary screens.
Verification Mode Date and Time User Menu
User Enroll Menu Settings Menu
14
E TTT S
E T TT S
KJ-3300(L)USER MANUAL ver.1.05www.ekjtech.co.kr
Move For ard
Move ack ard
To previous menu
ome Screen
Select the Menu
F
F
F
F
F
15
ESS T T E S STEE
ESS T T E S STE E
KJ-3300(L)USER MANUAL ver.1.05www.ekjtech.co.kr
Default condition and admin is not registered.
1 2 3 Menu Screen
F F
1. ress utton.
2.After 1 2 3 , ress utton
3.Succeed to access system menu
.Move bet een menus using or button
16
S
17
ESS T T E S STEE
ESS T T E S STE E
KJ-3300(L)USER MANUAL ver.1.05www.ekjtech.co.kr
Admin is registered already.
F F
Admin ID Verify Fingerprint or CD Main menu
nly hen admin is registered.Refer to Admin Registration artfor admin registration.
hen admin ID is incorrect, access to the system menu is denied.
hen admin ID is not registeredanyone can be access to systemmenu.So it is highly recommended to register admin More than one.
Unless stated other ise instructions in this manualstarts from system menu.
1. ress utton.
2. ress Registered admin ID and
3. Verify fingerprint or CD of the above ID
. Succeed to access system menu.
5. Move bet een menus using or button.
ress utton at the bottom left corner to return
home Screen.
18
E STE
E STE
KJ-3300(L)USER MANUAL ver.1.05www.ekjtech.co.kr
hen ADMIN is not registered
F
123 User Enroll
1. ress button
2. After 1 2 3 , press button (Access to the system menu)
3. Select User and press button
. Select Enroll and press button
5. Input pass ord(USER ID) and set up the privilege User or Admin. ( After User ID, press and set the privilege using the and button )
. Register fingerprints and or card ( Refer to p. 1 , Menu Navigation uttons )
F
19
E STE
E STE
KJ-3300(L)USER MANUAL ver.1.05www.ekjtech.co.kr
hen ADMIN is not registered
F
Admin ID Admin verification User . Enroll
F
Default admin ID is 123 . hen the ne admin is registered,
123 does not ork anymore.
Tip : In case of the absence of the admin, multiple admin is recommended
1. ress button
2. After Admin ID , press button
3. Verify Fingerprint or CD of the above Admin ID (Access to the system menu)
. Select Enroll and press button
5. Input pass ord(USER ID) and set up the privilege User or Admin. ( After User ID, press and set the privilege using the and button )
. Register fingerprints and or card ( Refer to p. 1 , Menu Navigation uttons )
20
SE E ST T
SE E ST T
KJ-3300(L)USER MANUAL ver.1.05www.ekjtech.co.kr
F
If doesn t need 2nd fingerprint or CARD, it is possible to skipthis process
1. Access to the system menu (Refer to . 1 or . 1 for access to the system menu)
2. o to User Enroll to process
3. Input pass ord ( User ID ) and
. Register 1st fingerprint
5. Scan fingerprint 3tiems for one registration
. Complete the registration of 1st fingerprint
. ress button and back to no. (If ant to register one fingerprint only, press F button an back to home screen)
. Select 2nd fingerprint
. Scan 2nd fingerprint three times
10. Complete fingerprint registration (If ant to register fingerprint only, press button an back to home screen)
11. ress button and back to no. for Card
12. Select Card
13. resent the card and read card data
1 . ress button
15. Complete registration
1 ress and back to home screen F
21
E ST T
E ST T
KJ-3300(L)USER MANUAL ver.1.05www.ekjtech.co.kr
If doesn t need 2nd fingerprint or CARD, it is possible to skipthis process
F
1. Access to the system menu (Refer to . 1 or . 1 for access to the system menu)
2. o to User Enroll to process
3. Input pass ord ( User ID ) and
. Move to privilege using F1 or F2 and select Admin using
( rivilege Admin K )
5. Move to K and press
. Register 1st fingerprint
. Scan fingerprint three times
. Complete the registration of 1st fingerprint (If ant to register one fingerprint only, press F button an back to home screen)
. ress button and back to no. to register 2nd fingerprint and repeat the same process
10. Select 2nd fingerprint
11. Scan 2nd fingerprint three times
12. Complete fingerprint registration (If ant to register fingerprint only, press button an back to home screen)
13. ress button and back to no. for Card
1 . Select Card
15. resent the card and read card data
1 . ress button
1 . Complete the registration
1 . ress and back to home screen
F F
F
F
22
ELETE
ELETE
KJ-3300(L)USER MANUAL ver.1.05www.ekjtech.co.kr
Same as registration process, it is able to delete 1st fingerprint,2nd fingerprint and card in each. If ish to delete all 3data, select Delete All and corresponding ID is deleted
1. Access to the system menu
(Refer to . 1 or . 1 for access to the system menu)
2. Select User
3. Select Delete
. Input pass ord ( User ID ) to delete
5. lace fingerprint or Card to delete
(If ant to delete both fingerprint and card of the ID, select Delete All.
. ress button after selection
. es and complete the delete
23
SET TE
SET TE
KJ-3300(L)USER MANUAL ver.1.05www.ekjtech.co.kr
Temp ID cannot be an Admin andnot use fingerprint Admin can determine access times of TempID (min. 1 ~ ma . ) Access times are e pired, Admin can revert it. emp ID leaves log data re-registered ID is not used as
a temp ID.
1. Access to the system menu
(Refer to . 1 or . 1 for access to the system menu)
2. ress button
3. Select User
. Select Set Temp ID
5. Input Temp ID ( upto digits) and press
. Input access admission times ith this temp ID and press
(Min. 1, Ma . )
. Compete setup temp ID.
24
L
L
KJ-3300(L)USER MANUAL ver.1.05www.ekjtech.co.kr
SETTIN 1. asic 2.Advanced 3.AC Setting .Communication 5.Schedule .Log Setting
asic
1.Time
2.Date
3.Date Format
.Language
5.Use usytone detection
. Set hone Numbers
Advanced
1.Vertification Mode
2.ID Mask
3.Use Tamer Alram
.Use Touch Sensor
5.Celibrate Senseor
.Restore Factory Settings
.Clear eneral Log
.Clear Management Log
.Clear Enroll Date
AC Settings
1.Define Time one
2.User Time one
3.Lock Type
.Lock Door Release Time
5.Door pen arning
.Re-access Count
.Re-access Limit Time
. iegand Format
.Anti- assback
25
L
L
KJ-3300(L)USER MANUAL ver.1.05www.ekjtech.co.kr
SETTIN 1. asic 2.Advanced 3.AC Setting .Communication 5.Schedule .Log Setting
Communication
1.Device ID
2. audrate
3.TC I Settings-D C-I Antipass-Subnet Mask-Default ate ay- ort-Mac Address
.Communication ass ord
Schedule
1.Set Tmode
2.Ring Settings
3.Auto Door
.Auto Funckey
5.None-Relat Funckey
.Day Light
. oliday
.Funckey Alarm
.Idle Settings
Log Setting
1.Management Log arning
2. eneral Log arning
26
S
S
KJ-3300(L)USER MANUAL ver.1.05www.ekjtech.co.kr
1. Time
Set-up the time of the device Device s time is applied to the time of the event. So it is important the accurate time.
2. Date
Setup the date of the device.
3. Date Format ( -MM-DD)
Define date format at home screen
. Language (Korean English)
Choose the language
5. Use usy tone detection (No es)
If the silent e ceeds 1minute, the phone disconnected automatically. Even visitors activate interphone, it returns standby mode and recommend to use.
. Set hone Numbers
hen interphone is connected, the receivers can remote control the door ith pass ord. nly registered phone numbers are able to control the door and available ma . 100 phone numbers.
27
E
E
KJ-3300(L)USER MANUAL ver.1.05www.ekjtech.co.kr
1. Verification Mode
Depends on the security level, it is able to ad ust the verification mode.
2. ID mask
hen the user input ID, it hides user ID as and enhance the security.
3. Use Tamer Alarm
hen it detects tamper, it activate alarm.
. Use Touch Sensor
If touch sensor is on, sensor lights off in normal condition and lights on hen the user touch the sensor only.
5. Calibrate Sensor
ptical sensor perceive surroundings and optimi e the brightness. hen use this function, it has to block e traneous light.
. Restore Factory Settings
Reset all settings to the default
. Clear eneral Log
Delete all general log data
. Clear Management Log
Delete all management log data
. Clear Enroll Data
Delete entire user data including fingerprint, card data and it is unrecoverable
28
E F T E
E F T E
KJ-3300(L)USER MANUAL ver.1.05www.ekjtech.co.kr
1. AN M DE : Access granted ith any form of authori ation
2. FIN ER : Fingerprint nly – No access ith ID or Card
3. CD R F
. ID F R CD
5. ID F R ID CD
. ID F R CD F
. EN : Al ays pen (Fail Safe Mode )
. CL SE : Al ays Closed (Fail-Secure Mode ) – No access ith any form of authori ation
. CD : Card nly – No access ith ID or Fingerprint
10. ID R F : ID or Fingerprint only – No access ith Card
11. ID R CD : ID or Card nly – No access ith Fingerprint
12. ID CD : oth ID and Card required for access – must punch in ID before Card authentication
13. CD F : oth Card and Fingerprint required for Access – Card must be authori ed before fingerprint authentication
1 . ID F : oth ID and Fingerprint required for Access – must punch in ID before fingerprint authentication
15. ID CD F : all three formats needed for access
29
SETT S
SETT S
KJ-3300(L)USER MANUAL ver.1.05www.ekjtech.co.kr
1.Define Time one : Able to set-up 25 time ones. ( Refer to Soft are ( uardian) manual .3 Time one set-up.
2.User Time one : Able to allocate 2 time one for each user. 0 for All Time and 25 for None Time .
3.Lock Type : NC or N Set up door lock type
.Lock Door Release Time : Default 3sec. Available to ad ust bet een 1 ~ sec.
5.Door pen arning : nce door open, if the door remains open over setting condition, it activates alarm
.Reaccess Count : No, 0~ Limit reaccess count bet een no., 0 ~ times.
.Reaccess Limit Time : Limit reaccess time bet een no. 0 ~ 00minutes.
. iegand Format : 2 ,3 ,35,3 ,Designate iegand output format 2 ,3 ,35,3 , or . Read all iegand data regardless of iegand settings
.Anti- assback : No es Anti-passback activates through e ternal iegand input. If there is t o controllers for enter and e it, re-enter is allo ed only it has e it event data(E : ublic arking lot, Restricted Area, Membership center )
30
T SSETT S
T S SETT S
KJ-3300(L)USER MANUAL ver.1.05www.ekjtech.co.kr
1 .Device ID (1 ~ ) Device ID ranges bet een 1 ~ .
hen many devices are connected in one net ork, each device must have unique address.
2. aud rate : 115200 bpsRS- 5 Communication speed
3. TC I Settings - D C : No es Choose D C on or off
- I Address : 1 2.1 .1.22 Setup I Address
- Subnet Mask : 255.255.255.0 Setup subnet mask
- Default ate ay : 1 2.1 .1.1Setup default gate ay
- ort : 5005 Setup TC ort
- MAC Address Displays MAC Address of the device
To connect device ith soft are ( uardian) by TC I ( LAN), it must set-up I Address, Subnet Mask, ate ay, (All the above data is for reference only and an confirm the details in net ork environment of the C to connect)
. Communication ass ordIf the communication pass ord is not correct, it is impossible to communicate ith the soft are
31
S E LE
S E LE
KJ-3300(L)USER MANUAL ver.1.05www.ekjtech.co.kr
1. Set Tmode Setup the door mode and it is converted automatically according to the time and schedule. Refer to Soft are ( uardian) manual - controller Special function Door mode ho to setup the door mode
2. Ring Settings Setup the bell ring schedule. Refer to Soft are ( uardian) manual - controller Special function ell Time ho to setup the bell rings
3. Auto Door Setup the operation time of the automatic door Refer to Soft are ( uardian) manual - controllerSpecial functionAuto Door ho to setup the auto door.
. Auto FunckeyAt the designated date and time, the corresponding key is set-up as default. Refer to Soft are ( uardian) manual - controller Special function auto F-Key ho to setup the auto F-Key.
5. None-Relay Funckey Setup none-relay Funckey and bu er alarm key. Refer to Soft are ( uardian) manual - controllerSpecial function No act F-Key ho to setup the No Act F-key.
32
S E LE
S E LE
KJ-3300(L)USER MANUAL ver.1.05www.ekjtech.co.kr
. Day Light Setup the daylight. Refer to Soft are ( uardian) manual - controllerSpecial functionDaylight ho to setup Daylight.
. oliday oliday settings must comply ith the day of the eek
Refer to Soft are ( uardian) manual - controller oliday setup
. Funckey Alarm nce input the alarm key and succeed to identify, it activates bu er alarm or relay alarm.
. CD2 Auto Funckey Input card data to the e ternal reader by iegand, and succeed to identify, it is used to save the event..
If a controller is connected to a reader, this function gives a function key to the e ternal reader automatically, thus a an automatically setup function key is given to a user ho is authori ed from an e ternal reader. Events of user entries from the reader are stored. (E . For time attendance)
10. Idle Settings LCD po er cut off : 0 ~ 0minutesIDLE mode : 0 ~ 0minutes
33
L SETT S
L SETT S
KJ-3300(L)USER MANUAL ver.1.05www.ekjtech.co.kr
1. Management Log arning ( 0 ~ 100) If the management logo e ceeds the setting value, it alarms
2. eneral Log arning If the management logo e ceeds the setting value, it alarms
34
S E
S E
KJ-3300(L)USER MANUAL ver.1.05www.ekjtech.co.kr
Insert US memory into the slot at the bottom of the device and up do nload the events data and update the firm are i
Do nload eneral log Do nload ne general events
Do nload All eneral log Do nload all general events
Do nload Management log Do nload ne management events
Do nload All Management log Do nload all management events
Do nload User Info Do nload user data
Upload User infoUpload user data
Upgrade Firm are Update Firm are
35
E
E
KJ-3300(L)USER MANUAL ver.1.05www.ekjtech.co.kr
1. User :User numbers hich is enrolled in the device
2. Fingerprint : Template numbers hich is enrolled in the device
3. ID Card : ID Card numbers hich is enrolled in the device
. eneral Log : eneral log ( access event ) numbers
5. Management Log : Management log ( system event ) numbers
36
E E F
E E F
KJ-3300(L)USER MANUAL ver.1.05www.ekjtech.co.kr
Device info is set from the manufacturer and the user cannot edit this info.
1. Release Date : Displays the device release date
2. Serial Number : Displays the device serial number
3. Manufacturer : Displays the device manufacturer
. roduct Name : Displays the device Name
5. roduct Type : Displays the device Type
. Engine Version : Displays the engine version
. Firm are Version: Displays the firm are version
37
E
E
KJ-3300(L)USER MANUAL ver.1.05www.ekjtech.co.kr
1.Vie eneral Log : Search and vie the general access event
2.Vie Management Log : Search and vie the system management event
3.Vie User info : Search and vie the numbers of the fingerprint and card
38
SELF TSET
SELF TEST
KJ-3300(L)USER MANUAL ver.1.05www.ekjtech.co.kr
Test All : Test overall status and functions of the device
Test Memory : Test memory and takes 1 ~ 2 minutes . After test, it reboots and displays the result
Test LCD : Test LCD
Test Sound ( Auto ) : Test Voice announcement automatically. If there is no voice chip, it finishes quickly
Test Sound ( Manual ) : Test Voice announcement manually.
Test Sensor : Test Finger sensor
Test Keyboard : Test keyboard
Test RTC : Test RTC
Test Case Status : Test the status of the case
Test Card Reader : Test the card reading
39