kingspan - byggematerialer · 08/2018 wall panel with visible ˜x and mineral wool insulation core....
TRANSCRIPT
-
08/2018
Wall panel with visible �x and mineral wool insulation core.
KingspanKS1150 FRProduct Data Sheet
Kingspan A/SMercurvej 12A9530 StøvringCVR-nr: 26065267Tel. +45 7021 7788E-mail: [email protected]
Insulated PanelsDenmark
Information about the product offer in otherscountries can be obtained from your localsales representative or on the websitewww.kingspan.com
Although Kingspan makes every efort to provide informationcontained in this publication were as accurate as possible,correct and complete, please note that its content should notbe the basis of the procedure in any particular case.Any advice, opinions, information or other content is publishedsolely based on the principle that neither the company, its employees or representatives, or people who contributed to the uprising of this publication, do not assume any liability for its content or any damage caused in connection with this content.
KINGSPAN STANDARD COLORS - EXTERIOR SIDE
Other colors from RAL and NCS palettes are also available on request, after prior consultation with Kingspan.
Exte
rior c
oat t
ypes
(f
or g
alva
nize
d st
eel) Po
lyes
ter
(PES
) – 2
5μm
RAL 9010 RAL 9002 RAL 7035 RAL 9006 RAL 9007
RAL 1015 RAL 3000 RAL 8004 RAL 5010 RAL 6020
RAL 7016 The colors are only illustrative in nature and may differ from the actual ones.
Standard interior colors for KS1000/1150/1200 FR panels are RAL 9010 PES, RAL 9002 PES or RAL 9002 PEI (dedicated for the inside of the panel).
Spec
trum
(PU
R) –
50μm
RAL 9010 RAL 9002 RAL 9006 RAL 9007
RAL 3009 RAL 7016 The colors are only illustrative in nature and may differ from the actual ones.
-
2
Product Data Sheet Wall Panels KS1150 FR with mineral wool core
Cross sectionmodule width 1000/1150/1200 mm
D
module module
Joint detail
Technical dataProfilations Geometry - dimensions in [mm] Exterior Interior
M (micro)
E(euro)
I (minibox)
B (box)
P (plank)
S (segment)*
K (plank 600)**
F (flat)
* Profilation S (segment) is recommended for the module 1000 mm. ** Profilation K (plank 600) is recommended for the module 1200 mm.
standard on request
50±0,5 50±0,5
1,5±
0,4
33,3 ±0,5 33,3±0,5
1±0,3
1,0±
0,2
40±0,5 10±0,5
1,2±
03
6±0,5
1,2±
03
6±0,5
200±0,5
25±0,5
8±0,5
0,7 ±
0,2
308±525±0,5
10 10 20±0,5
0,8
±0,3
Application
The KS1000/1150/1200 FR is a through-fixed wall system which can be laid vertically or horizontally and it is suitable for wall cladding on all types of buildings except where there are internal low temperature conditions (below 0 °C). The application of panel should be verified for each project individually, in order to meet the design requirements.
1,2±
03
6±0,5600±5 600±5
-
3
Wall Panels KS1150 FR with mineral wool core Product Data SheetPr
oduc
t
Mod
ule
[mm
]
Insulation core
thicknessD
[mm]
Weight[kg/m2]
Panel lengths
[m]
Number of
panels in
bundle[pcs]
Heat transfer
coefficientU
[W/(m2K)]for
λ = 0,044*(th. 60-80 mm;
175-200 mm)for
λ = 0,043**(th. 100-150 mm)
[W/mK]at temp. 10°C
Sound reduction
index[dB]
Fire parameters
KS10
00/1
150/
1200
FR
Thic
knes
s of
st
eel f
acin
gs
ext.
/int
. 0,
6 m
m /
0,5
mm
Min
.(1)
Max
.
R W RA1
RA
2
Reac
tion
to
fire
Fire
resi
stan
ce
1000
60 16,93
2,0
7,0 18 0,68*31 30 28
A2-s1, d0
EI 3080 19,33 9,0 14 0,52*
100 20,74
14,3
11 0,41**
32
31 29 EI 90120 22,94 9 0,35**
150 26,24 7 0,28** 32 29
EI 180175 30,73 6 0,25*31 29
200 33,73 5 0.22*
1150
60 16,77 7,0 18 0,68*31 30 28 EI 30
80 19,17 9,0 14 0,52*
100 20,58
14,3
11 0,41**
32
31 29 EI 90120 22,78 9 0,35**
150 26,08 7 0,28** 32 29
EI 180175 30,57 6 0,25*31 29
200 33,57 5 0,22*
1200
60 16,72 7,0 18 0,68*31 30 28 EI 30
80 19,12 9,0 14 0,52*
100 20,53
14,3
11 0,41**
32
31 29 EI 90120 22,73 9 0,35**
150 26,03 7 0,28** 32 29
EI 180175 30,52 6 0,25*31 29
200 33,52 5 0,22*
Note:1) At the request of the ordering party (for an additional fee) it is possible to deliver shorter panels. In other cases, short sections are combined in length meeting the production requirements.
Technical details
-
4
Product Data Sheet Wall Panels KS1150 FR with mineral wool core
Material• Exterior/Interior facings - Hot-dip zinc coated steel with a total of 275 g/m2 of zinc, according to EN 10 147:2000;• Insulation core - Insulation core made of Class A mineral wool;
Exterior coating options• Poliester - for the environment category up to C3;• PVDF - for the environment category up to C4;• Plastizol (PVC) - for the environment category up to C4;• Foodsafe (PVC) - for the environment category up to A3;*• Spectrum (PU) - for the environment category up to C5;
Interior coating options• Poliester - for the environment category up to C2; • Foodsafe (PVC) - for the environment category up to C4;• PVDF - for the environment category up to C4;• Spectrum (PU) - for the environment category up to C5;
*Outer coating allowed only for partition walls of the building.
Reference documents
KS1000/1150/1200 FR sandwich panels are manufactured in accordance with the EN 14 509 and CE marked.
Quality
Kingspan insulated sandwich panels are manufactured from the highest quality materials, using state of the art production equipment to rigorous quality control standards, complying with ISO 9001:2008 standards, ensuring long term reliability and service life.
Guarantees & Warranties
The Kingspan guarantees are individually assessed for each project, especially depending on the aggressiveness of the environment and the type of surface treatment chosen.
-
08/2018
Wall panel with visible �x and mineral wool insulation core.
KingspanKS1150 FRProduct Data Sheet
Kingspan A/SMercurvej 12A9530 StøvringCVR-nr: 26065267Tel. +45 7021 7788E-mail: [email protected]
Insulated PanelsDenmark
Information about the product offer in otherscountries can be obtained from your localsales representative or on the websitewww.kingspan.com
Although Kingspan makes every efort to provide informationcontained in this publication were as accurate as possible,correct and complete, please note that its content should notbe the basis of the procedure in any particular case.Any advice, opinions, information or other content is publishedsolely based on the principle that neither the company, its employees or representatives, or people who contributed to the uprising of this publication, do not assume any liability for its content or any damage caused in connection with this content.
KINGSPAN STANDARD COLORS - EXTERIOR SIDE
Other colors from RAL and NCS palettes are also available on request, after prior consultation with Kingspan.
Exte
rior c
oat t
ypes
(f
or g
alva
nize
d st
eel) Po
lyes
ter
(PES
) – 2
5μm
RAL 9010 RAL 9002 RAL 7035 RAL 9006 RAL 9007
RAL 1015 RAL 3000 RAL 8004 RAL 5010 RAL 6020
RAL 7016 The colors are only illustrative in nature and may differ from the actual ones.
Standard interior colors for KS1000/1150/1200 FR panels are RAL 9010 PES, RAL 9002 PES or RAL 9002 PEI (dedicated for the inside of the panel).
Spec
trum
(PU
R) –
50μm
RAL 9010 RAL 9002 RAL 9006 RAL 9007
RAL 3009 RAL 7016 The colors are only illustrative in nature and may differ from the actual ones.