k1612-26 series 12 hinge body - 3-4 slide retainer · 2 k1626 3/4 slide retainer assembly 43 5280...
TRANSCRIPT
DETAIL A
DETAIL B
DETAIL D
1
1
2
2
3
3
4
4
A A
B B
C C
D D
SHEET 1 OF 1
DRAWN
CHECKED
QA
MFG
APPROVED
Steve 1/19/2009
DWG NO
K1612/26
TITLE
Series 12 Hinge Body - 3-4 Slide Retainer -Assembly
SIZE
CSCALE
SignComp
REV
THIS DRAWING WAS CREATED AT NO CHARGE TO ASSIST YOU IN VISUALIZING OUR PROPOSAL. THE DRAWING HEREINIS THE PROPERTY OF SIGNCOMP. PERMISSION TO COPY OR REVISE THIS DRAWING OR TO USE THIS DRAWING FORPRODUCTION IS STRICTLY PROHIBITED AND CAN ONLY BE COPIED, REVISED OR USED FOR PRODUCTION WITH THEEXPRESSED WRITTEN PERMISSION OF SIGNCOMP.
A
B
Parts ListNOTESDESCRIPTIONPART #ITEM
AssemblySeries 12 Hinge BodyK16121Assembly3/4 Slide RetainerK16262Drill 11/32" Pilot HoleHinge Screw528043Drill #10 Counter SinkClosure Screw523044
NOTE: PRE-CUT KITS ARE NOT PRE-DRILLED.(Holes shown in this drawing are for reference only.Drilling of pilot holes are to be done by fabricator.)
DRIVE THE HINGE SCREWDOWN INTO THE BODY SOTHE HEAD OF THE HINGE
SCREW IS UNDER THESLIDE RETAINER AS SHOWN.
SEE DETAIL "D"1
2
43
43
44
44
2
44
44
43
43
2
1
2
44
1
1
243
DETAIL A
DETAIL B
1
1
2
2
3
3
4
4
A A
B B
C C
D D
SHEET 1 OF 1
DRAWN
CHECKED
QA
MFG
APPROVED
Steve 12/22/2008
DWG NO
K1612
TITLE
Series 12 Hinge Body - Assembly
SIZE
CSCALE
SignComp
REV
THIS DRAWING WAS CREATED AT NO CHARGE TO ASSIST YOU IN VISUALIZING OUR PROPOSAL. THE DRAWING HEREINIS THE PROPERTY OF SIGNCOMP. PERMISSION TO COPY OR REVISE THIS DRAWING OR TO USE THIS DRAWING FORPRODUCTION IS STRICTLY PROHIBITED AND CAN ONLY BE COPIED, REVISED OR USED FOR PRODUCTION WITH THEEXPRESSED WRITTEN PERMISSION OF SIGNCOMP.
A
B
Parts ListNOTESDESCRIPTIONPART #ITEM
Top & BottomSeries 12 Hinge Body16121SidesSeries 12 Hinge Body16122 Series 12 Hinge Body Corner Angle53423Drill 5/32" Pilot HoleCorner Angle Screw521813
NOTE: PRE-CUT KITS ARE NOT PRE-DRILLED.(Holes shown in this drawing are for reference only.Drilling of pilot holes are to be done by fabricator.)
1
22
13
33
13
13
3
13
13
3
13
132
1
3
13
13
DETAIL A
1
1
2
2
3
3
4
4
A A
B B
C C
D D
SHEET 1 OF 1
DRAWN
CHECKED
QA
MFG
APPROVED
Steve 12/22/2008
DWG NO
K1626
TITLE
3/4" Slide Retainer - Assembly
SIZE
CSCALE
SignComp
REV
THIS DRAWING WAS CREATED AT NO CHARGE TO ASSIST YOU IN VISUALIZING OUR PROPOSAL. THE DRAWING HEREINIS THE PROPERTY OF SIGNCOMP. PERMISSION TO COPY OR REVISE THIS DRAWING OR TO USE THIS DRAWING FORPRODUCTION IS STRICTLY PROHIBITED AND CAN ONLY BE COPIED, REVISED OR USED FOR PRODUCTION WITH THEEXPRESSED WRITTEN PERMISSION OF SIGNCOMP.
A
Parts ListNOTESDESCRIPTIONPART #ITEM
Top & Bottom3/4" Slide Retainer16261Sides3/4" Slide Retainer16262Special Corner Key for the 1626Corner Key52263#8 Counter Sink - Pre-Drilled3/4" Slide Retainer Corner Screw527059
NOTE: PRE-CUT KITS ARE NOT PRE-DRILLED.(Holes shown in this drawing are for reference only.Drilling of pilot holes are to be done by fabricator.)
1
59
3
2
59
1
59
2
3
3
59
59
1
3
2