K Swap Bolt-In Short Shifter Install Guide:

Features: Stainless Steel shifter rods Black Nickel Plated Steel Rockers Chrome Plated Spherical Bearings Aluminum Dust Shield 3 left/right throw settings 2 front/back throw settings Splined center shaft for adjustable shift

knob position Shift knob height adjustable to 5

different settings Rubber seal to keep out road noise,

debris, and exhaust heat

Package Contents: Short shifter assembly with

aluminum dust shield (4) M8 bolts, nuts, and

washers (for mounting shifter to chassis)

Adjustable offset block and shifter rod

Bolts, washers, and cotter pins for mounting cables

Rubber Gasket

Below you will find tips on how to install your new Hybrid Racing K Swap Bolt-In Short Shifter. *This shifter may not be legal for highway use. Hybrid Racing is not responsible for any direct or indirect, actual or inci-dental expense attributed to the use of any performance parts sold by Hybrid Racing LLC. Purchasers agree to all of the terms of this agreement upon the purchase of parts. More information can be found at www.hybrid-racing.com.

Important: The Hybrid Racing K Swap Bolt-In Short Shifter is capable of being adjusted to a throw much shorter than that of most production vehicles. For this reason, adjusting it to the shortest throw settings initially may cause a driver who is not experienced with such a short shift throw to accidentally “misshift”. Misshifts can potentially result in transmission or engine damage. For this reason, Hybrid Racing strongly recommends that all users drive with the shifter set to its longest throw settings until they are more comfortable with the shifter. It should be noted that even at its longest throw, Hybrid Racing’s shifter will still have a noticeably shorter throw than a stock K-series shifter, and even most aftermarket k series short shifters. Also, the shifter features several adjustments to position the knob in the most comfortable position. Hybrid Racing recommends that when initially mounting the black anodized offset block (this has the “hr” logo machined into it), the user positions it so that it is at the 6 0’clock position (i.e. such that it’s pointing towards the rear of the vehicle. This will cause the shifter to feel more like a traditional, non-adjustable shifter. Once you have acclimated to the unique feel of the shifter, then you can feel free to position it in whatever manner best suits your ergonomics.

Section 1: Drilling the bolt holes (note: if a Karcepts shifter adapter plate was previously installed in your vehicle, no holes need to be drilled. The Hybrid Racing shifter will bolt up to the same 4 holes that were used by the Karcepts shifter adapter plate.) Step 1a Unscrew the 4 M5 dust cover bolts (indicated by the white arrows in figure 1.a1) using a 3mm allen wrench, and remove the aluminum debris shield. Figure 1.a2 shows the underside of the shifter after the dust shield has been removed. Step 1b Place the shifter in the center tunnel from under car, and install 2 of the included M8 mounting bolts that go through the 2 rear holes in the shifter and into your chassis’ stock shifter mounting holes. The M8 bolts require a 6mm allen wrench. Torque until the shifter is flush with the chassis. Step 1c Locate the two front mounting holes for the shifter, and use a marker to mark the centers of the holes on the chassis. It may be necessary to use a metallic gel-type permanent marker or even chalk if you have dark paint or the center tunnel is dirty.

Install Guide: Installing this shifter is pretty straight forward. The guide below covers virtually every step involved in installing the shifter.

Step 1d Unbolt and remove the shifter from the chassis Step 1e Drill two holes in the center tunnel (Drill a 1/8” pilot hole, then open the holes up with a 3/8” bit). Section 2: Installing the Shifter Step 2a Because of clearance issues in the center tunnel, if OEM shifter cables are being used, they must be installed before the shifter is mounted to the chassis. (If Hybrid Racing Shifter Cables are being used, they can be installed before or after the shifter is mounted to the chassis i. The front/back cable should be installed with the spring clip inserted from the bottom. ii. For OEM cables, the left/right cable should be installed with the tab pointing down and then rotated 45 degrees (as illustrated in figures 2.a1 and 2.a2). For Hybrid Racing cables, install the left/right cable in the same manner the front/back cable was installed. Step 2b Before bolting the shifter to the chassis, the rubber seal that is included with the shifter should be placed on top of it. This rubber acts as a seal between the chassis and the shifter, preventing hot air, debris, moisture and excessive road noise from entering the cabin. Align the rubber on the top of the shifter so the four holes in it lineup with the four mounting holes on the shifter

Step 2c While holding the shifter against the underside of the center tunnel (as done in step 1.b), install the 2 supplied M8 bolts along with an M8 flat washer and lock washer. The lock washer should be sandwiched between the bolt and flat washer (as shown in figure 2c). Use a 6mm allen wrench to tighten the bolts (T handle allen wrenches work best here). As you torque down the two bolts, insure that the shifter is lined up properly with the two holes that were drilled for the front mounting bolts. Torque down the bolts until the lock washers have fully compressed. Step 2d From inside the cabin, install the 2 M8 bolts that thread into the front mounting holes for the shifter. Again, use the supplied M8 flat washers and lock washers, making sure the lock washer is sandwiched between the bolt and flat washer (as shown in figure 2c). Tighten these bolts until the lock washers have fully compressed. Step 2e After installing the mounting bolts on the top of the tunnel, the bottom ones may become loose. The mounting bolts that were installed in Step 2c should be checked and retightened if necessary.

Section 3: Adjusting Throw Step 3a First, the shifter cables will need to be be attached to their respective rockers. i. The cable controlled by the front/back motion of the shifter has two throw settings it can be adjusted to. The shifter has been supplied with It set to its longest throw setting. Hybrid Racing highly recommends that the shifter be set to its longest throw until the user has used the shifter enough to feel comfortable to shorten the throw. Adjusting the throw to the shortest setting initially may result in missing gears while shifting due to a lack of familiarity with the setup, thus possibly resulting in engine or transmission damage. ii. The cable controlled by the left/right motion of the shifter has three throw settings that it can be adjusted to. Again, Hybrid Racing highly recommends that the shifter be set to its longest throw until the user feels comfortable enough with the shifter’s short throw (compared to an RSX style shifter) to shorten the throw more. Step 3b To adjust the shifter’s throw, the bolt that each cable mounts to must be loosened from the cable’s respective steel rocker. Then reinserted in a different hole. The lower the cable is placed on the rocker, the shorter the shifter’s throw will be. The shifter is supplied in its longest throw configuration (which as mentioned earlier is still considerably shorter than a stock RSX’s throw).

Step 3c The cable should be slid onto the cable retaining bolt before the bolt has been fully tightened. A delrin washer is supplied on both cable retaining bolts and should be placed between the cable and the steel rocker for that cable. Step 3d The cable retaining bolt is installed along with a lock washer. The bolt should be tightened down until the lock washer has fully compressed. Step 3e Due to clearance issues, the cable retaining bolt for the cable controlled by the front/back motion of the shifter must be adjusted using a 5mm allen wrench, while the cable retaining bolt for the cable controlled by the lef/right motion of the shifter must be adjusted using a 13mm open or closed-ended wrench. Step 3f Once the cable has been placed on the retaining bolt and the bolt has been fully tightened, one of the supplied cotter pins should be reinserted into the hole at the end of the cable retaining bolt. Step 3g Once the cables are fully attached to the shifter, the debris shield can be bolted back onto the shifter. Use the 4 M5 bolts and lock washers that were removed in step 1.a.

Section 4: Adjusting the Shift Knob’s Position Step 4a The aluminum offset block has been supplied with the upper shift rod already bolted to it. This offset block can be positioned in 8 different positions, relative to the lower rod on the shifter. This feature has been included to allow the user to move the shift knob to a location that better suits them. Hybrid Racing highly recommends that the offset block be positioned in the 6 0’clock position until the user has become acclimated to the unique feel that the offset block gives the shifter. This position gives the shifter a feel much like most non- adjustable shifters. Using a 5mm allen wrench and the supplied M6 bolt and lock washer, bolt the black offset block to the lower shift rod. Torque down until the lock washer has been fully compressed. Step 4b The offset block was designed so that it could be positioned above or below the shift boot in most applications. If you wish to have the offset block visible after installation, the shift boot should be installed before the offset block. If you would like to cover the offset block with your shift boot, install the shift boot after installing the offset block. Step 4c The shift knob is also height adjustable. To adjust the knob's height, remove the two M4 bolts using a 3mm allen wrench. The knob can be adjusted in 10mm increments. While holding the upper rod in place, reinsert the two M4 bolts. Torque down the M4 bolts until the lock washers have fully compressed.

If you have any questions or comments, please email info@hybrid-racing.com or call us at 225-932-9588

Legal Disclaimer

Users assume all cost and risk associated with these or any other items purchased from Hybrid Racing LLC. Parts sold or manufactured by Hybrid Racing LLC may not meet legal requirements for use on public roads. People thinking about purchasing product(s) from Hybrid Racing LLC should check with their local and state authorities for legality. It is the user’s responsibility to know and comply with all local and federal laws and regulations. Use or installation of Hybrid Racing LLC products may affect user insurance and/or vehicle warranty coverage. It is the user’s sole responsibility for consequences that may occur due to having the product installed in his/her vehicle. Hybrid Racing LLC assumes no legal responsibilities and/or liabilities, whether to user’s vehicle, engine, person(s), and/or property(s), that result from the use of, or servicing of a vehicle of which a Hybrid Racing LLC product has been installed/attempted to be installed, or to any other vehicle(s) and/or person(s), regardless of whether or not this product has any involvement directly or indirectly and/or liability, and/or whether or not proper installation has been carried forth. All engines, engine parts and electrical components are for OFF ROAD USE ONLY/RACING VEHICLES ONLY. They are not for or to be used on public roads in the USA. Acquisition of a Hybrid Racing LLC product will act as an acknowledgement of the legal disclaimer stated herein. Hybrid Racing LLC reserves the right to change this disclaimer at any time without any prior consent or notification.

Should you need to contact us our details are as follows: Hybrid Racing LLC, 3348 Drusilla Lane, Suite 2C, Baton Rouge, LA 70809

www.hybrid-racing.com