jpx01 mdf product description

JPX01 MDF V200R001C01

Product Description

Issue 02

Date 2012-01-30

HUAWEI TECHNOLOGIES CO., LTD.

Issue 02 (2012-01-30) Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd

i

Copyright © Huawei Technologies Co., Ltd. 2012. All rights reserved.

No part of this document may be reproduced or transmitted in any form or by any means without prior written

consent of Huawei Technologies Co., Ltd.

Trademarks and Permissions

and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.

All other trademarks and trade names mentioned in this document are the property of their respective holders.

Notice

The purchased products, services and features are stipulated by the contract made between Huawei and the

customer. All or part of the products, services and features described in this document may not be within the

purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, and

recommendations in this document are provided "AS IS" without warranties, guarantees or representations of any

kind, either express or implied.

The information in this document is subject to change without notice. Every effort has been made in the preparation

of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this

document do not constitute a warranty of any kind, express or implied.

Huawei Technologies Co., Ltd.

Address: Huawei Industrial Base

Bantian, Longgang

Shenzhen 518129

People's Republic of China

Website: http://www.huawei.com

Email: [email protected]

http://www.huawei.com/

mailto:[email protected]

JPX01 MDF

Product Description 1 Product Positioning



ii

Contents

1 Product Positioning ...................................................................................................................... 1

2 Product Introduction .................................................................................................................... 2

2.1 Frame ............................................................................................................................................................... 2

2.1.1 Double-sided Frame ................................................................................................................................ 2

2.1.2 Single-sided Frame ................................................................................................................................. 4

2.2 Bracket ............................................................................................................................................................. 5

2.3 Terminal Block ................................................................................................................................................. 6

2.4 Protective Unit ................................................................................................................................................. 8

2.5 Accessories ..................................................................................................................................................... 10

2.5.1 IDC Tool ............................................................................................................................................... 11

2.5.2 Testing Cord .......................................................................................................................................... 11

2.5.3 Disconnection Plug ............................................................................................................................... 12

2.5.4 Labels .................................................................................................................................................... 13

2.5.5 Base ....................................................................................................................................................... 16

3 Application Scenarios ................................................................................................................ 18

4 Performance Indices ................................................................................................................... 20

5 Standard Compliance ................................................................................................................. 24

6 Acronyms and Abbreviations ................................................................................................... 25

A Product Detail List ..................................................................................................................... 26

B Product Packing Detail List ...................................................................................................... 28

JPX01 MDF




iii

Figures

Figure 1-1 JPX01 products series .......................................................................................................................... 1

Figure 2-1 JPX-F3D double-sided frame .............................................................................................................. 3

Figure 2-2 JPX-SF3D single-sided frame ............................................................................................................. 4

Figure 2-3 JPX01 bracket ...................................................................................................................................... 5

Figure 2-4 JPX01 Terminal block.......................................................................................................................... 7

Figure 2-5 Dimensions of the JPX01 terminal block ............................................................................................ 8

Figure 2-6 JPX01 protective unit .......................................................................................................................... 8

Figure 2-7 Grounding bar ...................................................................................................................................... 9

Figure 2-8 Application schematic drawing of grounding bar ................................................................................ 9

Figure 2-9 Dimensions of the JPX01 protective unit .......................................................................................... 10

Figure 2-10 Dimensions of the protective unit grounding bar ............................................................................. 10

Figure 2-11 JPX01-DXD IDC tool ...................................................................................................................... 11

Figure 2-12 JPX01-TC testing cord .................................................................................................................... 12

Figure 2-13 JPX01 disconnection plug ............................................................................................................... 12

Figure 2-14 JPX01 MDF label ............................................................................................................................ 13

Figure 2-15 JPX01-ML-10 module label holder ................................................................................................. 13

Figure 2-16 Application schematic drawing of module label holder ................................................................... 14

Figure 2-17 JPX01 number flag .......................................................................................................................... 14

Figure 2-18 Application schematic drawing of number flag ............................................................................... 14

Figure 2-19 JPX01-NL-10 hinged label holder ................................................................................................... 15

Figure 2-20 Application schematic drawing of hinged label holder .................................................................... 16

Figure 2-21 JPX01 MDF base ............................................................................................................................. 16

Figure 3-1 Application used in the equipment room ........................................................................................... 18

Figure 3-2 Application used in the outdoor cabinet ............................................................................................. 19

JPX01 MDF




iv

Tables

Table 2-1 Specifications of JPX-F3D double-sided frame .................................................................................... 3

Table 2-2 Specifications of JPX-SF3D single s-sided frame ................................................................................. 5

Table 2-3 Specifications of the JPX01 bracket ...................................................................................................... 6

Table 2-4 Specifications of the JPX01 terminal block ........................................................................................... 7

Table 2-5 Features of the JPX01 protective unit .................................................................................................... 9

Table 2-6 Specifications of the JPX01 protective unit ......................................................................................... 10

Table 2-7 Specifications of the JPX01-TC testing cord ....................................................................................... 12

Table 2-8 Specifications of JPX01 MDF base ..................................................................................................... 17

Table 4-1 The performance indices of JPX01 products ....................................................................................... 20

Table 4-2 Electric capability indexes of JPX01-SPD1-G400T ............................................................................ 22

Table 4-3 Electric capability indexes of JPX01-SPD1-G230F ............................................................................ 23

JPX01 MDF




1

1 Product Positioning

MDF (Main Distribution Frame) is the connection device between subscriber and exchange

device. For ensure the signal is integrated, MDF products efficiently distribute, protect and

management the network cables (copper cables).

JPX01 product is among the Huawei’s MDF product series. It implements the termination and

connection of external cables and exchange cables, to create a cable termination environment

for ADSL or VDSL service. JPX01 MDF supply the following accessorial equipment:

protective unit, testing cord and disconnection plug, has the function of over-voltage and

over-current protection, testing and controlling the lines connectivity.

JPX01 MDF includes abundant types: double-sided frame and single-sided frame, meeting the

scenario requirement of the inside environment; installed in the outdoor cabinet, meeting the

scenario requirement of the outside environment. As shown in Figure 1-1.

Figure 1-1 JPX01 products series

Double-sided frame Single-sided frame Outdoor cabinet

JPX01 MDF

Product Description 2 Product Introduction



2

2 Product Introduction

JPX01 consists of frame, bracket, terminal block, protective unit and accessories (including

IDC tool, testing cord, disconnection plug, labels and base).

2.1 Frame

The frame supplies installation carrier for the bracket and terminal block. There are two

models frame: double-sided frame and single-sided frame.

2.1.1 Double-sided Frame

The cable side terminal blocks and exchange side terminal blocks are installed on the different

sides of the double-sided frame. The cable side terminal block is vertically mounted on the

front pillar and exchange side terminal block is horizontally mounted on the back beam.

JPX01 double-sided frame has only one model available: JPX-F3D.

The product naming rules:

JPX: Mandatory product SN of MDF distribution product

F: Frame

3: The height is 2.2 m

D: The column quantity is 2

Appearance of JPX-F3D double-sided frame is shown in Figure 2-1.

JPX01 MDF




3

Figure 2-1 JPX-F3D double-sided frame

Features Constructed of metal frame structure, easy to install and has good capability.

Combined easily the left and right frames.

Supports full front-operation for convenient maintenance.

Enough space for layout of the cables, and the layout of the cables is orderly.

Specifications

Specifications of the JPX-F3D double-sided frame are shown in Table 2-1.

Table 2-1 Specifications of JPX-F3D double-sided frame

Model Dimensions (mm) External line Exchange line

H X W X D Cable tray height

Column Qty

Pair / column

Capacity (pair)

Row QTY

Pair / row

Capacity (pair)

JPX-F3D 2200 X 500 X 800 200 2 100 X 7 1400 6 100 X 2 1200

JPX01 MDF




4

2.1.2 Single-sided Frame

The cable side terminal blocks and exchange side terminal blocks are installed on the same

side of the single-sided frame, mounted alternately from the left side. JPX01 single-sided

frame has only one model available: JPX-SF3D.


JPX: Mandatory product SN of MDF distribution product

SF: Single frame

3: The height is 2.2 m

D: The column quantity is 2

Appearance of JPX-SF3D single-sided frame is shown in Figure 2-2.

Figure 2-2 JPX-SF3D single-sided frame

Features Constructed of metal frame structure, easy to install and has good capability.

Supports the installation near the wall for meeting the requirement of small equipment

office.

Flexible installation modes meet the different scenarios requirement: combined easily the

left and right frames, back-to-back installation, installed in the corner.

Supports full front-operation for convenient maintenance.

JPX01 MDF




5

The cable trough box on the bottom of the frame facilitates the layout of the cable. The

layout of the cable is advisable and clear.

Enough space for layout of the cables, and the layout of the cables is orderly.

Specifications

Specifications of the JPX-SF3D single-sided frame are shown in Table 2-2.

Table 2-2 Specifications of JPX-SF3D single s-sided frame

Model Dimensions (mm) External line Exchange line

H X W X D Cable tray height

Column Qty

Pair / column

Capacity (pair)

Column QTY

Pair / column

Capacity (pair)

JPX-SF3D 2200 X 500 X 600 200 1 100 X 7 700 1 70 X 10 700

2.2 Bracket

The bracket is used for installing the terminal block and fixing it on the frame. JPX01 bracket

has two models available: JPX01-BRK-11 and JPX01-BRK-8.


JPX01: Product model SN for Huawei's MDF distribution product

BRK: Bracket

11: 11 installation positions; 8: 8 installation positions

Appearance of the JPX01 bracket is shown in Figure 2-3.

Figure 2-3 JPX01 bracket

JPX01 MDF




6

Features The bracket for stainless steel is strong and durable.

Each bracket has one grounding finger. To supply grounding protection, the grounding

fingers belonged the same column are serial connection from beginning to end. The

ground wire is led to the frame grounding bar from the ground terminal of the downmost

bracket.

JPX01-BRK-11 has 11 installation positions for blocks: the first one is used for installing

the module label holder, the others is used for installing the terminal blocks.

JPX01-BRK-8 has 8 installation positions for blocks: the first one is used for installing

the module label holder, the others is used for installing the terminal blocks.

Specifications

Specifications of the JPX01 bracket are shown in Table 2-3.

Table 2-3 Specifications of the JPX01 bracket

Model Dimensions H X W X D (mm) Suitable for Frame Suitable for Terminal Block

JPX01-BRK-11 248 X 104 X 50 JPX-F3D Cable side terminal block

Exchange side terminal block

JPX-SF3D Cable side terminal block

JPX01-BRK-8 150 X 104 X 50 JPX-SF3D Exchange side terminal block

2.3 Terminal Block

Terminal blocks are the core parts for MDF. They create a cable termination environment for

external cable, exchange cable and jumper. JPX01 terminal block has two models available:

JPX01-BLK1-10K and JPX01-BLK1-10B.



BLK: Block

1: Product model SN for terminal block product

10: The capability is 10-pair

K: The IDC contact is switching contact; B: the IDC contact is disconnection contact

Appearance of the JPX01 terminal block is shown in Figure 2-4.

JPX01 MDF




7

Figure 2-4 JPX01 Terminal block

JPX01-BLK1-10K switching contact block JPX01-BLK1-10B disconnection contact block

Features Capacity: 10-pair/block.

Flexible IDC technology: 45o insulation displacement connection.

Transmission performance meets the Category 5 standards.

Compatible with the IDC tool for Krone type.

Full-front operation. Before you insert wire in maintenance, you should remove the

protective units of the adjacent ports.

JPX01-BLK1-10K is switching contact. It is usually used for the cable side terminal

block.

JPX01-BLK1-10B is disconnection contact. It is usually used for the exchange side

terminal block.

Specifications

Specifications of the JPX01 terminal block are shown in Table 2-4.

Table 2-4 Specifications of the JPX01 terminal block

Model Dimensions L X H X D (mm)

JPX01-BLK1-10K 126.6 X 23.4 X 40.9

JPX01-BLK1-10B

Dimensions of the JPX01 terminal block are shown in Figure 2-5.

JPX01 MDF




8

Figure 2-5 Dimensions of the JPX01 terminal block

2.4 Protective Unit

Protective unit is mainly used together with the cable side terminal block. It has over-voltage

and over-current protection capacity to protect the backward switching device. JPX01

protective unit have two models available: JPX01-SPD1-G400T and JPX01-SPD1-G230F.



SPD: Surge protective device

1: Product model SN for protective unit product

G: Gas discharge tube

400: DC breakdown voltage is 400V; 230: DC breakdown voltage is 230V

T: Three point protection; F: Five point protection

Appearance of the JPX01 protective unit is shown in Figure 2-6.

Figure 2-6 JPX01 protective unit

Features

Features of the JPX01 protective unit is shown in Table 2-5.

JPX01 MDF




9

Table 2-5 Features of the JPX01 protective unit

Model Over-voltage Protection

Over-current Protection

Protection Range

Transmission Performance

JPX01-SPD1-

G400T

Over-voltage

component is the

gas discharge tube:

Strong ability

for enduring

current

Many times for

surge current

impulsion

Without the over-current

protection device

Surge protection;

Electrical power

cable induction

protection;

Electrical power

cable connection

protection.

Supply VDSL2 service

JPX01-SPD1-

G230F

Over-current component

is high-speed and

macromolecule PTCR

(Positive Temperature

Coefficient Resistor).

Supply ADSL service

Matching with the grounding bar: each 10 pcs protective units matched with 1 pcs grounding

bar. As shown in Figure 2-7 and Figure 2-8 .

Figure 2-7 Grounding bar

Figure 2-8 Application schematic drawing of grounding bar

1. Cable side terminal block 2. Grounding bar 3. Protective unit

Specifications

Specifications of the JPX01 protective unit are shown in Table 2-6.

JPX01 MDF




10

Table 2-6 Specifications of the JPX01 protective unit

Model Dimensions L X H X D (mm)

JPX01-SPD1-G400T 9.4 X 13.2 X 52

JPX01-SPD1-G230F

Grounding bar 109 X 11.7 X 23.7

Dimensions of the JPX01 protective unit are shown in Figure 2-9.

Figure 2-9 Dimensions of the JPX01 protective unit

Dimensions of the protective unit grounding bar are shown in Figure 2-10.

Figure 2-10 Dimensions of the protective unit grounding bar

2.5 Accessories

JPX01 accessories cover IDC tool, testing cord, disconnection plug, labels and base.

JPX01 MDF




11

2.5.1 IDC Tool

IDC tool is used to clamp the cable into the spring plate or pull out the cable from the spring

plate, to implement cable connection or disconnection. JPX01 IDC tool only has one model

available: JPX01-DXD.



DXD: Code name for Huawei's IDC tool product

Appearance of the JPX01-DXD is shown in Figure 2-11.

Figure 2-11 JPX01-DXD IDC tool

Features After the wire is terminated, the redundant wires are automatically cut off.

Wire pulling-out hook and wire pressing-in fork equipped on the IDC tool can easily pull

out and press in the wire.

2.5.2 Testing Cord

The testing cord is used to lead the signal to test equipment, and test whether the signal

between ports is connected. JPX01 testing cord only has one model available: JPX01-TC.



TC: Testing cord

Appearance of the JPX01-TC testing cord is shown in Figure 2-12.

JPX01 MDF




12

Figure 2-12 JPX01-TC testing cord

Features Remove the protective unit before you used the testing cord.

Front-inserted.

A pair of red clips is connected to the internal line tester or telephone set; A pair of black

clips is connected to the external line tester (e.g. ohmmeter).

Specifications

Specifications of the JPX01 testing cord are shown in Table 2-7.

Table 2-7 Specifications of the JPX01-TC testing cord

Model Dimensions

JPX01-TC Testing plug L X H X D (mm) 9.2 X 14.2 X 60.6

Length for wire (m) 5

2.5.3 Disconnection Plug

The disconnection plug is used to disconnect the voice loop. Appearance of the JPX01

disconnection plug is shown in Figure 2-13.

Figure 2-13 JPX01 disconnection plug

Features Each 100-pair disconnection contact blocks (JPX01-BLK1-10B) match 5 pcs

disconnection plug automatically.

Front-inserted.

JPX01 MDF




13

One JPX01 disconnection plug disconnects one voice loop.

2.5.4 Labels

The labels are use for identifying the information such as line order of block. The JPX01

labels include MDF label, module label holder, number flag and hinged label holder.

MDF Label

The MDF label is used to identify the column of the cable side terminal block. Appearance of

the JPX01 MDF label is shown in Figure 2-14.

Figure 2-14 JPX01 MDF label

The features of JPX01 MDF label is following:

Each frame matches 1 pcs MDF label automatically.

It is white words on blue background and self-adhesive.

It can be directly stuck to the corresponding groove of the identification board on top of

the distribution frame.

Module Label Holder

The module label holder is used to identify the block information of the total bracket. JPX01

module label holder has only one model available: JPX01-ML-10.



ML: Module label

10: Used for 10-pair terminal block

Appearance of the JPX01 module label holder is shown in Figure 2-15.

Figure 2-15 JPX01-ML-10 module label holder

The features of JPX01-ML-10 module label holder are following:

Each bracket matches 1 pcs module label holder.

JPX01 MDF




14

JPX01-ML-10 is installed in the first installation position to identify the block

information of the total bracket.

The application of JPX01-ML-10 is shown in Figure 2-16.

Figure 2-16 Application schematic drawing of module label holder

Number Flag

The number flag is used to identify the series number of each terminal block. Appearance of

the JPX01 number flag is shown in Figure 2-17.

Figure 2-17 JPX01 number flag

The features of JPX01 number flag are following:

Each 100-pair terminal blocks match 1 pcs number flag automatically.

JPX01 number flag is installed in the one side of terminal block to identify the series

number.

The application of JPX01 number flag is shown in Figure 2-18.

Figure 2-18 Application schematic drawing of number flag

JPX01 MDF




15

Hinged Label Holder

The hinged label holder is used to identify each block information. JPX01 hinged label holder

has only one model available: JPX01-NL-10.



NL: Number label

10: Used for 10-pair terminal block

Appearance of the JPX01 hinged label holder is shown in Figure 2-19.

Figure 2-19 JPX01-NL-10 hinged label holder

The number flag and the hinged label holder are both used to identify the series number of each terminal

block. But they are suitable for different condition.

The number flag could be used whether the block installed the protective unit.

The hinged label holder is only used for the block without protective unit.

They will not be used at one time.

The features of JPX01-NL-10 hinged label holder is following:

Each terminal block matches 1 pcs hinged label holder.

JPX01-NL-10 is installed in front of the terminal block to identify the terminal block

information.

The application of JPX01-NL-10 hinged label holder is shown in Figure 2-20.

JPX01 MDF




16

Figure 2-20 Application schematic drawing of hinged label holder

2.5.5 Base

The base is optional parts. It is the support parts of ground-mount MDF. According the

different subscriber requirement, we could change the height of MDF through adjusting the

base height. JPX01 MDF base and JPX202 base is common. They have four models available:

JPX202-FD-DZA, JPX202-FD-DZB, JPX202-SFD-DZA, JPX202-SFD-DZB.



FD: 2-column frame; SFD: 2-column single frame

DZ: Code name for Huawei's base product

A, B: Product model SN for base product

Appearance of the JPX01 MDF base is shown in Figure 2-21.

Figure 2-21 JPX01 MDF base

Features The steel frame body is high intensity and anticorrosion.

Installation and operation is simple and easy.

The height is adjustable for convenient use.

JPX01 MDF




17

Specifications

Specifications of the JPX01 MDF base are shown in Table 2-8.

Table 2-8 Specifications of JPX01 MDF base

Model Dimensions H X W X D(mm) Suitable for Frame

Pitch Adjusting range for H W X D

JPX202-FD-DZA 10 180-320 (Without gasket)

185-325 (With gasket)

500 X 790 JPX-F3D double-sided frame

JPX202-FD-DZB 10 330-610 (Without gasket)


JPX202-SFD-DZA 10 180-320 (Without gasket)


500 X 590 JPX-SF3D single-sided frame

JPX202-SFD-DZB 10 330-610 (Without gasket)


JPX01 MDF

Product Description 3 Application Scenarios



18

3 Application Scenarios

JPX01 provides cable termination environment for the connection between the external cables

and switching equipment. It cooperates with Huawei’s MA5600T to provide xDSL service.

JPX01 can be used both in the equipment room (including the central office, remote office

and residential equipment room), and in the outdoor cabinet. It can be deployed in the new or

expansion project. The application of JPX01 products is shown in Figure 3-1 and Figure 3-2.

Figure 3-1 Application used in the equipment room

JPX01 MDF

Product Description 3 Application Scenarios



19

Figure 3-2 Application used in the outdoor cabinet

JPX01 MDF

Product Description 4 Performance Indices



20

4 Performance Indices

The performance indices of JPX01 products are shown in Table 4-1.

Table 4-1 The performance indices of JPX01 products

Performance Indices

Parameter Value Standard Compliance

Operating Condition

Application

class

Class 3.3 ETS 300019-1-3

Operating

temperature -25 to +65 --

Storage

temperature

-40 to +70 --

Relative

humidity 8％ to 100％ --

Atmospheric

pressure

70-106 kPa --

Material

Flammability Class V-0 UL94

Environment

protection

Meet RoHS requirement --

Plastic parts PC-FR UL94 V-0

Protective unit Grounding bar Cu H62-Y2 --

Over-voltage

component

GDT ITU/T Rec. K.12

Over-current

component PTCR ITU/T Rec. K.30

JPX01 MDF




21

Performance Indices


Block ID termination

material

Tin-phosphor bronze QSn6.5 --

Surface finishes Nickel-plate, local Gild (Au) --

Color Block RAL9010 (ID bracket)

RAL7035 (Pedestal)

--

Protective unit RAL 7035 --

Testing cord RAL 7035 --

Mechanical Capability

Block Solid wire

diameter range

0.4-0.65 mm (Insulation diameter ≤ 1.4 mm) --

Number of wire

terminations

≥ 100 IEC 11801

Number of

plugging

≥ 750 IEC 11801

Transverse

extraction force

≥ 50 N @ 0.5 mm --

Longitudinal

extraction force

≥ 10 N @ 0.5 mm --

Endurance Repeated insertion/withdrawals:

200 cycles from fully inserted to intermediate

position.

Maximum change in protector/block contact resistance

is less than 3 mΩ.

YD/T 694-2004

Environmental Adaptability

Temperature

variation

100 cycles × 1 h @ -40 / +70 IEC 11801

High

temperature

environment

500 h @ +70 IEC 11801

Temperature /

humidity

cycles

21 cycles × 24 h @ +25 / +65 / -10 / 93% RH IEC 11801

Vibration 20 cycles × 105 min/axis @ 1.0 mm, 10-55 Hz IEC 11801

JPX01 MDF




22

Performance Indices


Electric Capability

Block Resistance of

disconnection

contact

≤ 7 mΩ YD/T694-2004

IDC contact

resistance

≤ 3 mΩ YD/T694-2004

Insulation

resistance

≥ 1000 MΩ @ 500 V ± 50 V DC YD/T694-2004

Dielectric

strength

Without breakdown or arc@ 45-60 Hz, AC 1000V,

1min

IEC 60189-3

Protective unit Electric capabilities for the two models protective unit are very different.

The detailed indexes are shown in Table 4-2 and Table 4-3.

--

Transmission Capability

Transmission

performance

Class D IEC 11801

Table 4-2 Electric capability indexes of JPX01-SPD1-G400T

Electric Capability Parameter Value Standard Compliance

DC breakdown voltage 350-500 V @ 100 V/s ITU/T Rec. K.12

Insulation resistance ≥ 1000 MΩ @ 100 V DC YD/T 694-2004

Capacity (line to earth) ≤ 20 pF @ 1 MHz, 0.5 V --

Impulse breakdown voltage ≤ 800 V @ 100V/µs

≤ 950 V @ 1 kV/µs

ITU/T Rec. K.12

AC surge 600 V AC, 1s, 5 times @ 1 min intervals, 50 Hz ITU/T Rec. K.20

AC discharge 10 times @ 5 A applications each line side, 3 min

intervals, 50 Hz

ITU/T Rec. K.12

Impulse discharge current 300 times (alternating polarity) @ 100 A, 10/1000 µs

5 times of each polarity @ 2 kA (total current through

center electrode), 8/20 µs

YD/T 694-2004

Failure action time ≤ 15s @ 2A (1 A × 2), 600 VAC, 50 Hz --

JPX01 MDF




23

Table 4-3 Electric capability indexes of JPX01-SPD1-G230F

Electric Capability Parameter Value Standard Compliance

DC breakdown voltage 200 - 300 V @ 100 V/s ITU/T Rec. K.12

Insulation resistance ≥ 1000 MΩ @ 100 V DC YD/T 694-2004

Capacity (line to earth) ≤ 20 pF @ 1 MHz, 0.5 V --

Impulse breakdown voltage ≤ 600 V @ 100 V/µs

≤ 700 V @ 1 kV/µs

ITU/T Rec. K.12

PTCR room-temperature

resistance

≤ 22 Ω YD/T 694-2004

Hold current 120 mA @ +40, 1 h YD/T 694-2004

Over-current operating

characteristic ≤ 40s @ 0.35-0.1 A, 25

≤ 15s @ 0.5-0.1 A, 25

< 2s @ 1-0.1 A, 25

≤ 0.3s @ 3-0.1 A, 25

YD/T 694-2004

AC surge 600 VAC, 1s, 5 times @ 1 min intervals, 50 Hz ITU/T Rec. K.20

AC discharge 10 times @ 5 A applications each line side, 3 min

intervals, 50 Hz

ITU/T Rec. K.12

Impulse discharge current 300 times (alternating polarity) @ 100 A, 10/1000 µs

5 times of each polarity @ 2 kA (total current through

center electrode), 8/20 µs

YD/T 694-2004

Failure action time ≤ 15s @ 2A (1 A × 2), 600 V AC, 50 Hz --

JPX01 MDF

Product Description 5 Standard Compliance



24

5 Standard Compliance

International Standard

ETS 300019-1-3 Environmental conditions and environmental tests for telecommunications equipment - Part

1-3: Classification of environmental conditions; stationary use at weatherprotected locations

UL94 V-0 Test for Flammability of Plastic Materials for Parts in Devices and Appliances

IEC 11801 Information technology - Generic cabling for customer premises

ITU-T K.11 Principles of protection against overvoltages and overcurrents

ITU-T K.12 Characteristics of gas discharge tubes for the protection of telecommunications installations

ITU-T K.20 Resistibility of telecommunication equipment installed in a telecommunications centre to

overvoltages and overcurrents

ITU/T Rec. K.30 Positive temperature coefficient (PTC) thermistors

ITU/T K.44 Resistibility tests for telecommunication equipment exposed to overvoltages and

overcurrents - Basic Recommendation

ITU/T K.45 Resistibility of access network equipment to overvoltages and overcurrents

IEC 60189-3 Low-frequency cables and wires with P.V.C. insulation and P.V.C. sheath. Part 3: Equipment

wires with solid or stranded conductor, PVC insulated, in singles, pairs and triples

IEC 60068 Environmental Testing

National Standard

YD/T 694-2004 “Main Distribution Frame” and “Rules for Enforcement on Quality Authentication and

Inspection of MDF Homologation”

JPX01 MDF

Product Description 6 Acronyms and Abbreviations



25

6 Acronyms and Abbreviations

Abbreviation in English Full name in English

AC Alternating Current

ADSL Asymmetric Digital Subscriber Line

DC Direct Current

GDT Gas Discharge Tube

IDC Insulation Displacement Connection

MDF Main Distribution Frame

PC Polycarbonate

PTCR Positive Temperature Coefficient Resistor

VDSL Very High Speed Digital Subscriber Line

JPX01 MDF

Product Description A Product Detail List



26

A Product Detail List

Name Model Remark

Double-sided

frame

JPX-F3D External line capacity: 1400; Exchange line capacity: 1200

Single-sided

frame

JPX-SF3D External line capacity: 700; Exchange line capacity: 700

Bracket JPX01-BRK-11 11 installation position: one is used for the module label holder,

ten are used for the terminal blocks

Used for installing the exchange side and cable side terminal

block on the JPX-F3D, or installing the cable side terminal block

on the JPX-SF3D

JPX01-BRK-8 8 installation position: one is used for the module label holder,

seven are used for the terminal blocks

Used for installing the exchange side terminal block on the JPX-

SF3D

Terminal block JPX01-BLK1-10K 10-pair/block

Usually used for the cable side terminal block

JPX01-BLK1-10B 10-pair/block

Usually used for the exchange side terminal block

Protective unit JPX01-SPD1-G400T Gas discharge tube; Supply over-voltage protection; Supply

VDSL2 service

JPX01-SPD1-G230F Gas discharge tube; Supply over-voltage and over-current

protection; Supply ADSL service

IDC tool JPX01-DXD -

Testing cord JPX01-TC -

Disconnection

plug

- Each 100-pair disconnection contact blocks (JPX01-BLK1-10B)

match 5 pcs disconnection plug automatically

MDF label - Each frame matches 1 pcs MDF label automatically

JPX01 MDF

Product Description A Product Detail List



27

Name Model Remark

Module label

holder

JPX01-ML-10 Each bracket matches 1 pcs module label holder

Number flag - Each 100-pair terminal blocks match 1 pcs number flag

automatically

Hinged label

holder

JPX01-NL-10 Each terminal block matches 1 pcs hinged label holder

MDF Base JPX202-FD-DZA H adjustable range: 180-325 mm Suitable for JPX-F3D frame

JPX202-FD-DZB H adjustable range: 330-615mm

JPX202-SFD-DZA H adjustable range: 180-325 mm Suitable for JPX-SF3D frame

JPX202-SFD-DZB H adjustable range: 330-615 mm

JPX01 MDF

Product Description B Product Packing Detail List



28

B Product Packing Detail List

Model

Net Weight

(kg)

Packing Qty.

(pcs)

Packing Gross Weight

(kg)

Packing Size

H X W X D (mm) Remark

JPX202-F3D 66 1/box 87

2360 X 530 X 290

Wooden

box

packing JPX202-SF3D 57 1/box 78

JPX01-BRK-11 356 g 20/box 7.94 367 X 302 X 320

Box

packing

JPX01-BRK-8 276 g 20/box 6.15 367 X 302 X 253

JPX01-BLK1-10K 55 g 240/box

(20/carton X 12 cartons)

16.2 580 X 465 X 165

JPX01-BLK1-10B

JPX01-SPD1-G400T

4.2 g

1200/box

(40/carton X 30 cartons. Each

carton has 4 grounding strips in

it.)

8

540 X 322 X 214

JPX01-SPD1-G230F

JPX01-TC 120g 120/box

(1/packge X 120 packges) 15.2

570 X 340 X 295

JPX202-FD-DZA 14.8 1/box 15.3 200 X 520 X 810

JPX202-FD-DZB 18 1/box 18.5

JPX202-SFD-DZA 13.2 1/box 13.7 200 X 520 X 610

JPX202-SFD-DZB 16.5 1/box 17

jpx01 mdf product description

Documents

huawei trademarks

huawei proprietary

huawei industrial base

product positioning

product introduction

jpx01 mdf product description

singlesided frame

purchase scope