itp for cable tray installation

8/18/2019 ITP for Cable Tray Installation

1/4

21-May-12 Danny J.Y.Jeong K.J.Lim

Date Drawn Checked Approved

Owner :

A

Owner's Engineer :

Details of Revision

AES-VCM MONG DUONG

POWER COMPANY LIMITED

For Information

Rev.

oosan Heavy Industries

Vietnam

Dung Quat Economic Zone,

Binh Thuan, Binh Son, Quang Ngai,

Vietnam

T +84 55 5618 900

F +84 553 618 950

Page 1

Project : PC : T10206

UAS : QE01

Unit : PO

Title :KKS : ZEN

Reg. No.

Revision : A

Drawing No. : Page-No :

T10206-QE01-POZEN__-040203 INSPECTION

AND TEST PLAN FOR

CABLE TRAYS INSTALLATION

040203

T10206-QE01-P0ZEN-040203

MONG DUONG II 2 X 560MW (NET) COAL FIRED POWER PROJECT

1 of 4

Contractor :

Page 1


2/4

Rev. A

2 of 4

This note is only applicable for AES-VCM Mong Duong

Detailed Legend

S : Surveillance Point / DOOSAN / Subcontractor does not send a notification to AES-VCM Mong Duong

except for the first or last operation on the basis of each process. AES-VCM Mong Duong

could check the operation, if he is present at the site during the inspection by Doosan.

R : Report Review Point / DOOSAN / Subcontractor is required to prepare a certificate or document

attesting to the satisfactory performance of the related test or inspection for review by

-

T10206-QE01-POZEN-040203

DOOSAN

AES-VCMITP for Cable Tray Installation

Doc. No.

Contractor

Page 2

- .

W : Witness Point / DOOSAN / Subcontractor shall submit request for inspection to AES-VCM to

decide whether they will attend such inspection or not.

H : Hold Point / Downstream construction and other activities shall not proceed

without attendance or any written approval of AES-VCM Mong Duong.

NOTE : The Site ITP and all of the abovementioned reports will be kept available by

DOOSAN at anytime for control and or review by AES-VCM Mong Duong.

Page 2


3/4

Doc. No.

Contractor

A Sign A Sign A Sign

R R R

R R R

H W WB1Check the installation is according to the designed

layout drawing & specification.

Approved Construction

Drawing T10206-YD04---

AES-VCM

A.Material

Receipt

A1Check the condition of cable Supports, Racks, Trays

and Trunking while receiving.Packing List

A2Check size and type of the Supports, Racks, Trays

and Trunking with respect to the requisitions.

Material Technical

Specification

Item Name Oper. No. Inspection Process

Specific Applicable drawing

number, Standard Code number,Specification

Inspection & Test Activities

Subcontractor DOOSAN

Inspection & Test Plan for Cable Tray

InstallationAES-VCM

H W W

H W W

H W W

H W W

H W W

H W W

Abb revi atio n : S: Surveillance R: Report Review W: Witness Inspection H: Hold Inspection

Note : All inspection shall be performed in accordance with the approved Site Inspection and Test Plans/Project Specifications

B. Cable

Tray

Installation

Ensure the cable trays numbered according to

cable trays route layout on which KKS nos. are

indicated and explained.

Approved ConstructionDrawing T10206-YD04---

B5Ensure there are no sharp 90 degrees bends are

made.



B6

Ensure the cable trays numbered according to cable

trays route layout on which KKS nos. are indicated and

explained.



B7

No sharp edges cut to be permitted. Cutting edges of

trays/trunkings are touch-up painted.



B4Ensure the gap between parallel runs is quite enough

to accommodate the layer of cables.



B3

B2

expansion joints if any are specified are in place.



4/4

Project : Cable Tray Installation Works Ref. No.

Drawing No. : Date :Specific Location :

Yes No N/A

1

2

3

4

5

6

7

8

9

10

DOOSAN Electrical Dept.

Name & Signature Name & Signature Name & Signature Name & Signature

Position Position Position Position

Date Date Date Date

page 4

Ensure there are no sharp 90 degrees bends are made.

hecked by : (Subcontractor DOOSAN QA/QC Dept. AES-VCM

Ensure the cable trays numbered according to cable trays route

layout on which KKS nos. are indicated and explained.

Check whether the exclusive earth continuity between the trays /

trunking / racks where the joints are made.

Earth jumper cable with crimp type terminals to be fitted to all cable

tray joints.

Check the condition of cable Supports, Racks, Trays and Trunking while

receiving.

Check size and type of the Supports, Racks, Trays and Trunking with

respect to the requisitions.

Check the installation is according to the designed layout drawing &

specification.

Check the leveling & alignment of tray & rack and expansion joints if

any are specified are in place.

No sharp edges cut to be permitted. Cutting edges of trays/trunkings are

touch-up painted.

Ensure the gap between parallel runs is quite enough to accommodate the

layer of cables.

Inspection Check List

CHECK ITEM

No Inspection elements

Verification & Approval Observed

Result

/ Remarks

itp for cable tray installation

Documents