isr6200 command line interface (cli) user’s...

ISR654601-00 E

iSR6200Command Line Interface (CLI)

User’s Guide

ii ISR654601-00 E

iSR6200 Command Line Interface (CLI)

User’s Guide

Information furnished in this manual is believed to be accurate and reliable. However, QLogic Corporation assumes no responsibility for its use, nor for any infringements of patents or other rights of third parties which may result from its use. QLogic Corporation reserves the right to change product specifications at any time without notice. Applications described in this document for any of these products are for illustrative purposes only. QLogic Corporation makes no representation nor warranty that such applications are suitable for the specified use without further testing or modification. QLogic Corporation assumes no responsibility for any errors that may appear in this document.

Document Revision History

Revision A, February 20, 2009

Revision B, November 24, 2009

Revision C, March 19, 2010

Revision D, January 28, 2011

Revision E, September 13, 2011

Changes Sections Affected

Updated to latest QLogic template. All

Added note regarding location of data migration commands.

“What’s in This Guide” on page xi

Corrected the QLogic Training e-mail link. “Training” on page xiv

Updated example output for the help command. “Help” on page 2-18

Added new commands to Chapter 2 Command Reference.

“iSCSI” on page 2-28

“LUN iSCSI Global Map” on page 2-31

“LUN Remap” on page 2-38

“Remote Mappings” on page 2-45

“Remote Peers” on page 2-48

“Set Event Notification” on page 2-61

“Set SNMP” on page 2-70

“Set NTP” on page 2-68

“Show Event Notification” on page 2-81

“Show Feature Keys” on page 2-84

“Show I/O Statistics” on page 2-89

“Show Remote Maps” on page 2-116

“Show Remote Peers” on page 2-117

“Show RPC Info” on page 2-118

“Show SmartWrite Devices” on page 2-119

“SmartWrite Device” on page 2-134

“Target Map” on page 2-136


User’s Guide

ISR654601-00 E iii

Added new syntax and keywords to the set and show commands.

“Set” on page 2-55

“Show” on page 2-74

iv ISR654601-00 E


User’s Guide

ISR654601-00 E v

Table of Contents

Preface

Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiWhat’s in This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiRelated Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiiDocumentation Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiiiLicense Agreements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xivTechnical Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiv

Training . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xivContact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvKnowledge Database . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv

1 CLI Usage

Logging on to a SAN Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1Understanding the Guest Account . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2Working with SAN Router Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

Modifying a Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4Saving and Restoring Router Configurations . . . . . . . . . . . . . . . . . . . 1-4

Saving Blade Configuration and Persistence . . . . . . . . . . . . . . . 1-4Restoring Router Configuration and Persistence . . . . . . . . . . . . 1-5

Installing the Firmware Via Telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

2 Command Reference

Command Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1Chassis Management Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1Blade Management Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Command Syntax. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5Command Line Completion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5Authority Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6Admin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7Beacon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9Clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10Date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11

vi ISR654601-00 E


User’s Guide

Commands (continued)Exit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12FCIP Route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13FRU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-24Image. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-25Initiator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-26iSCSI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-28Logout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-30LUN iSCSI Global Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-31LUN Mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-34LUN Remap. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-38Password. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-41Ping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-42Quit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-43Reboot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-44Remote Mappings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-45Remote Peers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-48Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-52Save . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-53Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-55Set Alias . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-57Set CHAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-59Set Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-60Set Event Notification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-61Set FC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-62Set Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-63Set iSCSI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-64Set iSNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-65Set MGMT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-66Set NTP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-68Set Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-69Set SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-70Set System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-72Set VPGroups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-73Show . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-74Show CHAP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-78Show Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-79

ISR654601-00 E vii


User’s Guide

Commands (continued)Show Event Notification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-81Show FC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-82Show FCIP Routes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-83Show Feature Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-84Show Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-85Show Initiators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-86Show Initiators LUN Mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-88Show I/O Statistics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-89Show iSCSI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-90Show iSNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-94Show Logs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-95Show LUN Info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-96Show LUNs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-98Show LUN Mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-100Show Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-102Show MGMT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-103Show NTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-104Show Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-105Show Port Statistics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-108Show Presented Targets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-112Show Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-115Show Remote Maps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-116Show Remote Peers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-117Show RPC Info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-118Show SmartWrite Devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-119Show SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-120Show Stats. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-121Show Stats FCIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-126Show System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-128Show Targets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-129Show VPGroups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-131Shutdown. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-133SmartWrite Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-134Target. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-135Target Map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-136Traceroute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-139

viii ISR654601-00 E


User’s Guide

3 Configuring CHAP

Discovery Session—Bi-directional CHAP . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2Discovery Session—Uni-directional CHAP . . . . . . . . . . . . . . . . . . . . . . . . . 3-3Normal Session—Bi-directional CHAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4Normal Session—Uni-directional CHAP . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

4 Virtual Port Groups

Displaying Virtual Port Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2Enabling Virtual Port Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

5 Configuring Fibre Channel Initiators to iSCSI Storage

Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1Configuration Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Step 1: Discover the iSCSI Targets . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2Using the iSCSI Discover Command . . . . . . . . . . . . . . . . . . . . . 5-2Using iSNS Server Connectivity . . . . . . . . . . . . . . . . . . . . . . . . . 5-3

Step 2: Log into the iSCSI Targets. . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6Step 3: Zone the Fibre Channel Host and iSR6200 Router. . . . . . . . . 5-6Step 4: Map the iSCSI Target into the SAN and Provide Host

Access to the Storage LUN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7Step 5: View the Newly Mapped Target Zoned to the Fibre

Channel Host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9

A Simple Network Management Protocol

SNMP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2SNMP Trap Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3Management Information Base (MIB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4

Network Port Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4Fibre Channel Port Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-7Initiator Object Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-9LUN Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-12Virtual Port Group Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-14Sensor Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-16

Notifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-19System Information Objects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-19Notification Objects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-20Agent Startup Notification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-21Agent Shutdown Notification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-21Network Port Down Notification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-21Fibre Channel Port Down Notification . . . . . . . . . . . . . . . . . . . . . . . . . A-22Target Device Discovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-22

ISR654601-00 E ix


User’s Guide

Notifications (continued)Target Presentation (Mapping) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-22Virtual Port Group Notification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-23Sensor Notification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-23Generic Notification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-24FCIP Route Notification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-25

B Log Messages

Glossary

Index

List of FiguresFigure Page

5-1 iSNS Server Properties: Creating a Discovery Domain . . . . . . . . . . . . . . . . . . . . . . 5-45-2 iSNS Server Properties: Enabling a Discovery Domain Set . . . . . . . . . . . . . . . . . . 5-55-3 Zone Configured with Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-75-4 iSCSI Configured with Router to Fibre Channel SAN . . . . . . . . . . . . . . . . . . . . . . . 5-10

List of TablesTable Page

2-1 CLI Chassis Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12-2 CLI Blade Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22-3 Command Line Completion Keystrokes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-55-1 Zone Host with Router—Fibre Channel-Based Ports . . . . . . . . . . . . . . . . . . . . . . . 5-7A-1 SNMP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2A-2 SNMP Trap Configuration Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3B-1 iSR6200 Router Log Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2

x ISR654601-00 E


User’s Guide

ISR654601-00 E xi

Preface

The iSR6200 Command Line Interface (CLI) User’s Guide describes how to use the command line interface (CLI) to configure and manage the QLogic iSR6200 Intelligent Storage Router (iSR6200).

Intended AudienceThis user’s guide is intended for individuals who are responsible for installing, managing, and servicing the iSR6200 router and the storage area network (SAN) equipment to which it is attached.

What’s in This GuideThis user’s guide contains the basic information you need to get started with the CLI-based iSR6200 management tool.

This preface specifies the intended audience, explains the typographic conventions used in this guide, lists related documents, and provides technical support and contact information.

The remainder of the guide is organized into the following chapters and appendices:“What’s in This Guide” on page 1-xi

Chapter 1 CLI Usage specifies how to log on to a SAN router, describes the guest account, and shows how to work with router configurations.

Chapter 2 Command Reference lists and describes each of the CLI commands, including the syntax, keywords, notes, and examples.

Chapter 3 Configuring CHAP provides procedures for setting up the challenge handshake authentication protocol (CHAP) for discovery sessions and normal sessions with both bi-directional and uni-directional CHAP.

NOTE:

This guide does not cover commands specific to data migration, an optional, licensed feature available for the iSR6200. For details about data migration commands, refer to the Data Migration Service for iSR6200 User’s Guide, available on any of the iSR6200 Series product download pages on QLogic.com.

http://www.qlogic.com



xii ISR654601-00 E

Chapter 4 Virtual Port Groups describes how to view and enable up to four virtual port groups (VPGs), required if you want iSCSI hosts to have access to more than 256 distinct logical unit numbers (LUNs) from a specified Fibre Channel target array.

Chapter 5 Configuring Fibre Channel Initiators to iSCSI Storage provides instructions for connecting Fibre Channel hosts to iSCSI targets using the QLogic iSR6240 and iSR6250 routers.

Appendix A Simple Network Management Protocol describes how to use the simple network management protocol (SNMP) to monitor and manage the router through third-party applications that support SNMP version 1 and 2 and a QLogic management information base (MIB).

Appendix B Log Messages provides details about messages logged to a file, including message categories for informational, error, and fatal log messages.

Following the appendices are a glossary of terms used and an index to help you quickly find the information you need.

Related MaterialsFor additional information related to the iSR6200, refer to the following documents:

iSR6200 Quick Start Guide, part number SN0054504-00

iSR6200 Intelligent Storage Router Installation Guide, part number ISR651101-00

iSR6200 Router Manager User's Guide, part number ISR654602-00

Internet Protocol, Version 6 (IPv6) Specification, RFC2460

Neighbor Discovery for IP Version 6 (IPv6), RFC2461

IPv6 Stateless Address Auto-configuration, RFC2462

Internet Control Message Protocol (ICMPv6) for the Internet Protocol Version 6 (IPv6) Specification, RFC2463

Transmission of IPv6 Packets over Ethernet Networks, RFC2464

iSCSI draft standard draft-ietf-ips-iSCSI-20

Internet engineering task force (IETF): iSCSI Requirements and Design Considerations, iSCSI Naming and Discovery, Internet Protocol Specification (IPv4), RFC793

Transmission Control Protocol (TCP) Specification, RFC1122, Requirements for Internet Hosts-Communication Layers

TCP Extensions for High Performance, RFC1323

ISR654601-00 E xiii

TCP Congestion Control, RFC2581

ANSI SCSI: SCSI-3 Architecture Model (SAM), X3T10/994D/Rev 18, SCSI-3 Controller Command Set, X3T10/Project 1047D/Rev 6c. IEEE: 802.1Q Virtual LAN (VLAN), 802.1p Priority of Service, 802.3x Flow Control, 802.3ad Link Aggregation

SCSI-3 Fibre Channel Protocol (SCSI-FCP), X3.269:1996

Fibre Channel Physical and Signaling Interface (FC-PH), X3.230:199

Fibre Channel 2nd Generation (FC-PH-2), X3.297:1997

Third Generation Fibre Channel Physical and Signaling Interface (FC-PH-3), X3.303:1998, Fibre Channel-Arbitrated Loop (FC-AL-2), working draft, revision 6.4, August 28, 1998

Fibre Channel Fabric Loop Attachment Technical Report (FC-FLA) NCITS/TR-20:1998, Fibre Channel-Private Loop Direct Attach Technical Report (FC-PLDA)

SCSI Fibre Channel Protocol-2 (FCP-2) working draft, revision 3, October 1, 1999

ANSI Information Technology-SCSI 3 Architecture Model, revision 18, November 27, 1995

Documentation ConventionsThis guide uses the following documentation conventions:

Text in blue font indicates a hyperlink (jump) to a figure, table, or section in this guide. Links to Web sites are shown in underlined blue. For example:

See “Admin” on page 5-5.

Table A-1 describes the SNMP properties.

For more information, visit www.qlogic.com.

Text in monospace font indicates a file name, directory path, or command line text. For example:

Generate a file (iSR6200_FRU.bin) containing the saved data.

Type of restore (0=full, 1=mappings only) [full]

Use the show iscsi command to find the iSCSI node name of the GE port.

xiv ISR654601-00 E

Text in bold monospace font indicates text you type at a command line. For example:

iSR6200 <1>(admin) #> fru restore

iSR6200 <1> #> show vpgroups

Text in italics indicates terms, emphasis, variables, or document titles. For example:

For a complete listing of license agreements, refer to the QLogic Software End User License Agreement.

Each iSR6200 blade supports up to four virtual port groups (VPGs).

When prompted, enter the <ip_address>.

Text in ALL CAPITALS indicates the name of a key that you press on the keyboard. For example:

Press the CTRL+Q keys.

Type the number for Host Information, and then press ENTER.

License AgreementsRefer to the QLogic Software End User License Agreement for a complete listing of all license agreements affecting this product.

Technical SupportCustomers should contact their authorized maintenance provider for technical support of their QLogic switch products. QLogic-direct customers may contact QLogic Technical Support; others will be redirected to their authorized maintenance provider.

For details about available service plans, or for information about renewing and extending your service, visit the Service Program Web page at http://www.qlogic.com/services.

TrainingQLogic offers training for technical professionals for all iSCSI, InfiniBand, and Fibre Channel products. From the main QLogic Web page at www.qlogic.com, click the Support tab at the top, and then click the Education & Training on the left. The QLogic Global Training Portal offers online courses, certification exams, and scheduling of in-person training.


http://www.qlogic.com/services

ISR654601-00 E xv

Technical Certification courses include installation, maintenance and troubleshooting QLogic products. Upon demonstrating knowledge using live equipment, QLogic awards a certificate identifying the student as a certified professional. You can reach the training professionals at QLogic by e-mail at [email protected].

Contact InformationQLogic Technical Support for products under warranty is available during local standard working hours excluding QLogic Observed Holidays. For customers with extended service, consult your plan for available hours. For Support phone numbers, see the Contact Support link at http://support.qlogic.com.

Knowledge DatabaseThe QLogic knowledge database is an extensive collection of QLogic product information that you can search for specific solutions. We are constantly adding to the collection of information in our database to provide answers to your most urgent questions. Access the database from the QLogic Support Center: http://support.qlogic.com.

Support Headquarters QLogic Corporation4601 Dean Lakes Blvd.Shakopee, MN 55379 USA

QLogic Web Site www.qlogic.com

Technical Support Web Site http://support.qlogic.com

Technical Support E-mail [email protected]

Technical Training E-mail [email protected]

http://support.qlogic.com




mailto:[email protected]



xvi ISR654601-00 E

ISR654601-00 E 1-1

1 CLI Usage

The iSR6200 CLI enables you to perform a variety of router management tasks through an Ethernet or serial port connection. This chapter provides details about the following tasks:

Logging on to a SAN Router

“Understanding the Guest Account” on page 1-2

“Working with SAN Router Configurations” on page 1-4

“Installing the Firmware Via Telnet” on page 1-6

Logging on to a SAN RouterYou can either use Telnet or Secure SHell (SSH) to log on to a router, or you can log on to the router through the serial port.

To log on to a router using Telnet:

1. On the workstation, open a command line window.

2. Enter the telnet command followed by the router IP address:

# telnet <ip_address>

A Telnet window opens and prompts you to log in.

3. Enter an account name and password.

To log on to a router using SSH:

SSH works similar to Telnet, except it uses RSA to encode transmissions to and from your workstation and the iSR6200 blade.

1. On the workstation, open a command line window.

2. Enter the ssh command followed by the router IP address:

# ssh <ip_address>

An SSH window opens and prompts you to log in.

3. Enter an account name and password.

1–CLI Usage

Understanding the Guest Account

1-2 ISR654601-00 E

To log on to a switch through the serial port:

1. Configure the workstation port with the following settings:

115200 baud 8-bit character 1 stop bit No parity

2. When prompted, enter an account name and password.

Understanding the Guest AccountRouters come from the factory with the following account already defined:

This guest account provides access to the router and its configuration. After planning your router management needs, consider changing the password for this account. For information about changing passwords, see the passwd command (page 2-41).

The guest account is automatically closed after 15 minutes of inactivity.

The initial login opens at the chassis level. From the chassis level, select the blade to be managed. For example:

iSR6200 login: guest

Password: *********

******************************************************

* *

* ISR6200 *

* *

******************************************************

iSR6200 #> help

admin [ begin | end | start | stop | cancel ]

blade [ 1 | 2 ]

exit

help

history

logout

quit

Account name: guest

Password: password

1–CLI Usage

Understanding the Guest Account

ISR654601-00 E 1-3

reset [ factory | mappings ]

show [ chassis ]

iSR6200 #> show chassis

Chassis Information

---------------------

Product Name ISR6200

Chassis Name Router Chassis Name

Serial Number 0834E00019

HW Version 20697-03 A

Fan Speed Normal

Blade 1 Information (Left Slot)

-------------------------------

Status Online

Product Name iSR6200

Symbolic Name Blade-1



SW Version 3.3.0.0

Temp (Front/Rear/CPU1/CPU2) 44C/33C/34C/38C

Power Cooling Module 1

----------------------

Status Installed

Power Source Connected

Fan1/Fan2/Fan3 Healthy/Healthy/Healthy

Blade 2 Information (Right Slot)

--------------------------------

Status Offline


----------------------

Status Installed



iSR6200 #> blade 1

iSR6200 <1> #>

1–CLI Usage

Working with SAN Router Configurations

1-4 ISR654601-00 E

Working with SAN Router ConfigurationsSuccessfully managing routers with the command line interface depends on effective router configurations. Key router management tasks include modifying configurations, backing up configurations, and restoring configurations.

Modifying a ConfigurationThe router has these major areas of configuration:

Management port configuration requires using the following commands:

set mgmt (see page 2-66)

show mgmt (see page 2-103)

ISCSI port configuration requires using the following commands:

set iscsi (see page 2-64)

show iscsi (see page 2-90)

Virtual port groups configuration requires the following commands:

set vpgroups (see page 2-73)

show vpgroups (see page 2-131)

LUN mapping requires using the following command:

lunmask add (see page 2-34)

Saving and Restoring Router ConfigurationsSaving and restoring a configuration helps protect your work. You can also use a saved configuration as a template for configuring other routers.

Saving Blade Configuration and PersistencePersistent data consists of system settings, virtual port group settings, LUN mappings, discovered Fibre Channel targets, and discovered iSCSI initiators.

To save a blade’s configuration and persistent data:

1. To generate a file (iSR6200_FRU.bin) containing the saved data (see page 2-17), execute the fru save command.

This command stores the file locally on the router in an FTP directory.

2. To transfer the saved data from the router to a workstation, execute an FTP utility on a workstation.

1–CLI Usage

Working with SAN Router Configurations

ISR654601-00 E 1-5

The following example shows an FTP transfer to get the saved router configuration data:

c:\> ftp 172.17.137.102

Connected to 172.17.137.102.

220 (none) FTP server (GNU inetutils 1.4.2) ready.

User (172.17.137.102:(none)): ftp

331 Guest login ok, type your name as password.

Password: ftp

230 Guest login ok, access restrictions apply.

ftp> bin

200 Type set to I.

ftp> get iSR6200_FRU.bin

200 PORT command successful.

150 Opening BINARY mode data connection for 'iSR6200_FRU.bin' (6168 bytes).

226 Transfer complete.

ftp: 6168 bytes received in 0.00Seconds 6168000.00Kbytes/sec.

ftp> quit

221 Goodbye.

Restoring Router Configuration and Persistence

To restore the router’s configuration and persistent data:

1. To transfer the saved data from a workstation to the router, execute an FTP utility on the workstation.

The following example shows an FTP transfer to put previously saved router configuration data on the router:

c:\> ftp 172.17.137.102

Connected to 172.17.137.102.


User (172.17.137.102:(none)): ftp


Password: ftp


ftp> bin

200 Type set to I.

NOTE:

Dual-bladed iSR6200s automatically restore a field replaceable unit (FRU) on a new blade anytime it is detected in the chassis.

1–CLI Usage

Installing the Firmware Via Telnet

1-6 ISR654601-00 E

ftp> put iSR6200_FRU.bin


150 Opening BINARY mode data connection for 'iSR6200_FRU.bin'.


ftp: 6168 bytes sent in 0.00Seconds 6168000.00Kbytes/sec.

ftp> quit

221 Goodbye.

2. To update a blade with the saved configuration data (see page 2-17), execute the fru restore command. The fru restore command has the following two options:

Full restore—Restores all router configuration parameters, including IP addresses, subnet masks, gateways, virtual port group settings, LUN mappings, and all other persistent data.

Partial restore—Restores only the LUN mappings and persistent data, such as discovered Fibre Channel targets and iSCSI initiators.

Installing the Firmware Via TelnetThis section provides the steps required for installing the iSR6200 router firmware.

To install the firmware via Telnet:

1. Download the iSR6200 Router firmware to your workstation from the QLogic Web site:

http://driverdownloads.qlogic.com/QLogicDriverDownloads_UI/default.aspx

2. Change to the directory where the firmware image file is located.

3. Unzip the firmware file before proceeding to the next step.

4. Transfer the image from your workstation to the router. For example:

a. On your workstation, open a command window. (On a Windows OS, click Start, and then click Run. In the Run dialog box, type cmd, and then click OK.)

b. Change to the directory where the firmware image file is located:

C:\>cd \fwImage (example directory containing the firmware image)

http://driverdownloads.qlogic.com/QLogicDriverDownloads_UI/default.aspx

1–CLI Usage


ISR654601-00 E 1-7

c. Use the file transfer protocol (FTP) to transfer the firmware image to the router. For example:

C:\fwImage>ftp 172.17.137.190 (example IP address)

Connected to 172.17.137.190.


User (172.17.137.190:(none)): ftp


Password: ftp


ftp> bin

200 Type set to I.

ftp> put isr-6200-3_3_1_1.bin (example file name)


150 Opening BINARY mode data connection for 'isr-6200-3_3_1_1.bin'.


ftp: 4822816 bytes sent in 0.41Seconds 11878.86Kbytes/sec.

ftp> quit

221 Goodbye.

C:\fwImage>

5. Install the firmware image on the router. For example:

iSR6200 login: guest

Password: password (default login password)

******************************************************

* *

* ISR6200 *

* *

******************************************************

iSR6200 #>

iSR6200 #> blade 1 (specify blade to be updated, 1 or 2)

iSR6200 <1> #> admin start

Password : config (default admin password)

iSR6200 <1> (admin) #> image list

Image Location Image File

-------------- ----------

Blade 1 (local) isr-6200-3_3_1_1.bin (example file name)

iSR6200 <1> (admin) #> image unpack isr-6200-3_3_1_1.bin (example file name)

1–CLI Usage


1-8 ISR654601-00 E

Unpack Completed. A reboot is required for the FW to take affect.

Do you wish to reboot the System at the current time (y/n): y (if there are two blades, update both blades before rebooting)System will now be rebooted...

ISR654601-00 E 2-1

2 Command Reference

This chapter lists and describes the iSR6200 Intelligent Storage Router CLI commands in alphabetical order. Each command description includes its syntax, keywords, notes, and examples.

Command ListsThe tables in this section provide references to the chassis level and blade level commands used in the iSR6200 CLI.

Chassis Management CommandsTable 2-1 provides a link to the section containing details of each CLI chassis management command.

Table 2-1. CLI Chassis Commands

For Commands Starting with: Refer to Section:

B “Blade” on page 2-9

E “Exit” on page 2-12

H “Help” on page 2-18“History” on page 2-24

L “Logout” on page 2-30

Q “Quit” on page 2-43

S “Show Chassis” on page 2-79

2–Command Reference

Command Lists

2-2 ISR654601-00 E

Blade Management CommandsTable 2-2 provides a link to the section containing details of each CLI blade management command.

Table 2-2. CLI Blade Commands


A “Admin” on page 2-7

B “Beacon” on page 2-8

C “Clear” on page 2-10

D “Date” on page 2-11

E “Exit” on page 2-12

F “FCIP Route” on page 2-13“FRU” on page 2-17

H “Help” on page 2-18“History” on page 2-24

I “Image” on page 2-25“Initiator” on page 2-26“iSCSI” on page 2-28

L “Logout” on page 2-30“LUN iSCSI Global Map” on page 2-31“LUN Mask” on page 2-34

P “Password” on page 2-41“Ping” on page 2-42

Q “Quit” on page 2-43

R “Reboot” on page 2-44“Remote Mappings” on page 2-45“Remote Peers” on page 2-48“Reset” on page 2-52

S “Save” on page 2-53“Shutdown” on page 2-133“SmartWrite Device” on page 2-134


Command Lists

ISR654601-00 E 2-3

Set “Set” on page 2-55“Set Alias” on page 2-57“Set CHAP” on page 2-59“Set Chassis” on page 2-60“Set Event Notification” on page 2-61“Set FC” on page 2-62“Set Features” on page 2-63“Set iSCSI” on page 2-64“Set iSNS” on page 2-65“Set MGMT” on page 2-66“Set NTP” on page 2-68“Set Properties” on page 2-69“Set SNMP” on page 2-70“Set SNMP” on page 2-70“Set System” on page 2-72“Set VPGroups” on page 2-73

Table 2-2. CLI Blade Commands (Continued)



Command Lists

2-4 ISR654601-00 E

Show “Show” on page 2-74“Show CHAP” on page 2-78“Show Chassis” on page 2-79“Show Event Notification” on page 2-81“Show FC” on page 2-82“Show FCIP Routes” on page 2-83“Show Features” on page 2-85“Show Initiators” on page 2-86“Show Initiators LUN Mask” on page 2-88“Show I/O Statistics” on page 2-89“Show iSCSI” on page 2-90“Show iSNS” on page 2-94“Show Logs” on page 2-95“Show LUN Info” on page 2-96“Show LUNs” on page 2-98“Show LUN Mask” on page 2-100“Show Memory” on page 2-102“Show MGMT” on page 2-103“Show NTP” on page 2-104“Show Performance” on page 2-105“Show Port Statistics” on page 2-108“Show Presented Targets” on page 2-112“Show Properties” on page 2-115“Show Remote Maps” on page 2-116“Show Remote Peers” on page 2-117“Show RPC Info” on page 2-118“Show SmartWrite Devices” on page 2-119“Show SNMP” on page 2-120“Show Stats” on page 2-121“Show Stats FCIP” on page 2-126“Show System” on page 2-128“Show Targets” on page 2-129“Show VPGroups” on page 2-131

T “Target” on page 2-135“Target Map” on page 2-136“Traceroute” on page 2-139

Table 2-2. CLI Blade Commands (Continued)



Command Syntax

ISR654601-00 E 2-5

Command SyntaxThe iSR6200 CLI command syntax uses the following format:

commandkeywordkeyword [value]keyword [value1] [value2]

The command is followed by one or more keywords. Consider the following rules and conventions:

Commands and keywords are case insensitive.

Required keyword values appear in standard font within brackets; for example, [value].

Optional keyword values appear in italics within brackets; for example, [value].

In command prompts, <1> or <2> indicates which blade is being managed.

Command Line CompletionThe command line completion feature simplifies entering and repeating commands. Table 2-3 describes the command line completion keystrokes.

Table 2-3. Command Line Completion Keystrokes

Keystroke Effect

TAB Completes the command line. Type at least one character, and then press the TAB key to complete the command line. If more than one possibility exists, press the TAB key again to view all possibilities.

UP ARROW Scrolls backward through the list of previously entered commands.

DOWN ARROW Scrolls forward through the list of previously entered commands

CTRL+A Moves the cursor to the beginning of the command line.

CTRL+E Moves the cursor to the end of the command line.


Commands

2-6 ISR654601-00 E

Authority RequirementsThe various set commands perform tasks that may require you to be in an administrator session. Note that:

Commands related to monitoring tasks are available to all account names.

Commands related to configuration tasks are available only within an Admin session. An account must have Admin authority to enter the admin start command, which opens an admin session (see “Admin” on page 2-7).

Commands


Commands

ISR654601-00 E 2-7

AdminOpens and closes an administrator (Admin) session. Any command that changes the router configuration must be done in an Admin session. An inactive Admin session will time out after 15 minutes.

Authority Admin session

Syntax adminstart (or begin)end (or stop)cancel

Keywords start (or begin)

Opens the Admin session.

end (or stop)

Closes the Admin session. The logout, shutdown, and reset commands also end an Admin session.

cancel

Terminates an Admin session opened by another user. Use this keyword with care because it terminates the Admin session without warning the other user and without saving pending changes.

Notes Closing a Telnet window during an Admin session does not release the session. When using Telnet, you must either wait for the Admin session to time out, or use the admin cancel command.

Examples The following example shows how to open and close an Admin session:

iSR6200 <1> #> admin start

Password : ******

iSR6200 <1> (admin) #>

.

.

.

iSR6200 <1> (admin) #> admin end

iSR6200 <1> #>


Commands

2-8 ISR654601-00 E

BeaconEnables or disables flashing the blue beacon LED.

Authority None

Syntax beacononoff

Keywords on

Turns on the router beacon.

off

Turns off the router beacon.

Examples The following example shows the beacon command:

iSR6200 <1> #> beacon on


Commands

ISR654601-00 E 2-9

BladeAllows for the selection of the blade to be managed. This command is only valid at the chassis prompt.

The chassis CLI prompt does not include the blade number (for example, iSR6200 #>), whereas the blade CLI prompt includes the blade number (for example, iSR6200 <1> #>).

Authority None

Syntax blade [1 or 2]

Examples The following example of the blade command shows blade 2 being selected from the chassis prompt, followed by a quit command at the blade prompt, which returns control to the chassis prompt:

iSR6200 #> blade 2

iSR6200 <2> #> quit

iSR6200 #>


Commands

2-10 ISR654601-00 E

ClearRemoves all entries (events) from the router log file, or resets the Fibre Channel and iSCSI statistic counters.


Syntax clear logsstats

Keywords logs

Clears all entries from the router’s log file.

stats

Resets the statistic counters.

Examples The following examples show the clear commands:

iSR6200 <1> (admin) #> clear logs

iSR6200 <1> (admin) #> clear stats


Commands

ISR654601-00 E 2-11

DateDisplays or sets the date and time. To set the date and time, you must enter the information in the format MMDDhhmmCCYY (numeric representation of month-date-hour-minute-century-year). The new date and time takes effect immediately.

Each blade has its own independent date set. Properly setting the date ensures that event log entries are dated correctly. The date must be set prior to applying any feature keys or licenses.

Authority Admin session required to set the date and time. No authority is required to display the current date and time.

Syntax date[MMDDhhmmCCYY]

Keywords [MMDDhhmmCCYY]

Specifies the date—this requires an Admin session. If you omit [MMDDhhmmCCYY], the command displays the current date, which does not require an Admin session.

Notes Always set the time using Greenwich Mean Time (GMT) and Universal Transverse Mercator (UTM).

You must disable the network time protocol (NTP) to set the time with the date command. Refer to the set ntp command on page 2-68 for information about NTP.

Examples The following examples show the date command:

iSR6200 <1> (admin) #> date 010214282011

Fri Jan 2 14:28:00 2011

iSR6200 <1> (admin) #> date

Fri Jan 2 14:28:14 2011


Commands

2-12 ISR654601-00 E

ExitExits the command line interface and returns you to the login prompt. (Same as the quit command.)

Authority None

Syntax exit

Examples The exit command behaves differently depending on whether you at the chassis or blade management level.

At the chassis management level, exit returns you to the login prompt. The following example shows the exit command for the chassis:

iSR6200 #> exit

iSR6200 login:

At the blade management level, exit returns you to the chassis management level. The following example shows the exit command for the blade:

iSR6200 <1> (admin) #> exit

iSR6200 #>


Commands

ISR654601-00 E 2-13

FCIP RouteConfigures a new Fibre Channel over IP (FCIP) route and lets you modify or delete an existing FCIP route.

Each FCIP route requires a dedicated Fibre Channel and Gigabit Ethernet port. Configuring an FCIP route and specifying a Fibre Channel and Gigabit Ethernet (GE) port pair takes precedence over any previously existing configuration for the port pair (FC/GE), and removes the existing configuration of the port pair.


Syntax fciprouteaddmodrm

Keywords add

Configures a new FCIP route.

mod

Modifies an existing FCIP route.

rm

Removes an existing FCIP route.

Notes You can also configure an FCIP route over a 10Gb Ethernet port, provided that the router has both an available 10Gb port and the FCIP 10Gb license installed. The same FCIP commands (fciproute add, fciproute mod, and fciproute rm, as well as show fciproutes) can be used to configure, remove, and view the FCIP route through a 10Gb Ethernet port. See the example in the following.

Examples The following shows an example of the fciproute add command:

iSR6200 <1> (admin) #> fciproute add

A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so.

WARNING:

The following command might cause a loss of connections to both GE ports.

Configuring FCIP Route:

-----------------------

FCIP Interfaces FC & GE (0=Enable, 1=Disable) [Enabled ]

FC Port (1=FC1 2=FC2) [ ] 1


Commands

2-14 ISR654601-00 E

GE Port (1=GE1 2=GE2) [ ] 1

IP Address (IPv4 or IPv6; 0=IPv6 Link Local) [0.0.0.0 ] 172.35.15.11

Subnet Mask [0.0.0.0 ] 255.255.254.0

Gateway IP Address [0.0.0.0 ] 172.35.14.1

Remote IP Address [0.0.0.0 ] 172.17.136.18

MTU Size (0=Normal, 1=Jumbo, 2=Other) [Normal ]

TCP Window Size (0=8KB, 1=16KB, 2=32KB) [32768 ]

Window Scaling (0=Enable, 1=Disable) [Enabled ]

Window Scaling Factor (Min=0, Max=9) [7 ]

TCP Port No. (Min=1024, Max=65535) [3225 ]

GE Port Speed (0=Auto, 1=100Mb, 2=1Gb) [Auto ]

Bandwidth, Mbit/sec (Min=1, Max=1000) [1000 ]

VLAN (0=Enable, 1=Disable) [Disabled ]

FCIP SW Compression(0=Enable,1=Disable,2=Auto)[Auto ]

All attribute values for FCIP Route 1 will now be saved.

The following shows an example of the fciproute add command used to add a 10Gb FCIP route. At the GE Port prompt, you must select a 10Gb Ethernet port. Set the Window Scaling Factor to 3 for the default window size. Set the Bandwidth, Mbit/sec in a range from 1Mbps to 10000 Mbps.

iSR6200 <1> (admin) #> fciproute add


WARNING:



-----------------------


FC Port (1=FC1 2=FC2) [ ] 1

GE Port (1=GE1 2=GE2 3=10GE1 4=10GE2) [ ] 3

IP Address (IPv4 or IPv6; 0=IPv6 Link Local) [0.0.0.0 ] 172.35.15.11

Subnet Mask [0.0.0.0 ] 255.255.254.0

Gateway IP Address [0.0.0.0 ] 172.35.14.1

Remote IP Address [0.0.0.0 ] 172.17.136.18






Commands

ISR654601-00 E 2-15




FCIP SW Compression(0=Enable,1=Disable,2=Auto)[Disabled ]


The following shows an example of the fciproute mod command:

iSR6200 <1> (admin) #> fciproute mod


WARNING:


Route FC Port ID GE Port ID

----- ---------- ----------

1 FC1 GE1

Please select a FCIP route from the list above ('q' to quit): 1


-----------------------


IP Address (IPv4 or IPv6; 0=IPv6 Link Local) [172.35.15.11 ]

172.35.15.120

Subnet Mask [255.255.254.0 ]

Gateway IP Address [172.35.14.1 ]

Remote IP Address [172.17.136.18 ]






GE Port Speed (0=Auto, 1=100Mb, 2=1Gb) [Auto ]



FCIP SW Compression(0=Enable,1=Disable,2=Auto) [Auto ]

Do you want to save/discard changes? (0=Save, 1=Discard) [Save ]



Commands

2-16 ISR654601-00 E

The following shows an example of the fciproute rm command:

iSR6200 <1> (admin) #> fciproute rm


WARNING:


Route FC Port ID GE Port ID

----- ---------- ----------

1 FC1 GE1

Please select a FCIP route from the list above ('q' to quit): 1

FCIP Route 1 has been removed from the system.


Commands

ISR654601-00 E 2-17

FRUSaves and restores the router’s configuration.

Authority Admin session to restore

Syntax frurestore save

Keywords restore

The fru restore command requires that you first FTP the tar file containing the configuration to the router. When you issue this command, the system prompts you to enter the restore level. You can fully restore the router’s configuration (all configuration parameters and LUN mappings) or restore only the LUN mappings. The restored configuration does not take effect until the router is rebooted.

save

The fru save command creates a tar file containing the blade’s persistent data, configuration, and LUN mappings. The file is stored in the router’s /var/ftp directory. You must then FTP the tar file from the router.

Examples The following example shows the fru restore command:

iSR6200 <1> (admin) #> fru restore


Type of restore (0=full, 1=mappings only) [full]

FRU restore completed.

Please reboot the system for configuration to take affect.

The following example shows the fru save command:

iSR6200 <1> (admin) #> fru save

FRU save completed. Configuration File is QLogic_Router_FRU.bin

Please use FTP to extract the file out from the System.


Commands

2-18 ISR654601-00 E

HelpLists the iSR6200 CLI commands and their syntax. The iSR6200 includes the following help command sets:

General iSCSI Server Connectivity Data Migration SAN over WAN

Authority None

Syntax help

Examples This section provides examples of each help command set. The help command differs for the chassis and the blade.

The following example shows the help command for the chassis:

iSR6200 #> help


blade [ 1 | 2 ]

exit

help

history

logout

quit


show [ chassis ]

The following example shows the help command for the blade:


Commands

ISR654601-00 E 2-23

show [ remotepeers | remotemaps ]

show remotepeers

show remotemaps


Commands

2-24 ISR654601-00 E

History Lists numerically the previously entered commands.

Authority None

Syntax history

Examples The following example shows the history command:

iSR6200 <1> (admin) #> history

1: admin start

2: help

3: history

iSR6200 <1> (admin) #>


Commands

ISR654601-00 E 2-25

ImageUpdates the router’s firmware image and cleans up (removes) the image files in the router’s /var/ftp directory.


Syntax imagecleanuplist [file]unpack [file]

Keywords cleanup

Removes all firmware image files in the router’s /var/ftp directory. These are files transferred by the user when updating the router’s firmware image.

list [file]

Lists the firmware image files in the router’s /var/ftp directory.

unpack [file]

Unpacks the firmware image file specified in the [file] parameter and installs the firmware image on the router. Prior to using this command, you must first transfer the firmware image file to the router’s /var/ftp directory using FTP. To activate the new firmware, you must reboot the router.

Examples The following example shows the image cleanup command:

iSR6200 <1> (admin) #> image cleanup

The following example shows the image list command:

iSR6200 <1> (admin) #> image list

Image Location Image File

-------------- ----------

Blade 1 (local) isr-6200-3_0_0_5.bin

The following example shows the image unpack command:

iSR6200 <1> (admin) #> image unpack iSR6200-2_0_0_1.bin

Unpack Completed. Please reboot the system for FW to take effect.

iSR6200 <1> (admin) #> reboot

Are you sure you want to reboot the System (y/n): y

System will now be rebooted...


Commands

2-26 ISR654601-00 E

InitiatorAdds, modifies, and removes an initiator in the router’s database.


Syntax initiatoraddmod remove

Keywords add

Adds an initiator to the router’s database.

mod

Modifies the settings of an initiator.

rm (remove)

Removes a logged-out initiator. You cannot remove an initiator that is currently logged in.

Examples The following example shows the initiator add command:

iSR6200 <1> (admin) #> initiator add


Only valid iSCSI name characters will be accepted. Valid characters include lower-case alphabetical (a-z), numerical (0-9), colon, hyphen, and period.

iSCSI Initiator Name (Max = 223 characters) [ ]iqn.1991-05.com.microsoft:qlogic-09sd5i4l

OS Type (0=MS Windows, 1=Linux, 2=Other) [MS Windows ]

All attribute values for that have been changed will now be saved.

The following example shows the initiator mod (modify) command:

iSR6200 <1> (admin) #> initiator mod

Index (WWNN,WWPN/iSCSI Name)

----- ----------------------

0 iqn.1991-05.com.microsoft:qlogic-09sd5i4l

Please select an Initiator from the list above ('q' to quit): 0


Commands

ISR654601-00 E 2-27


OS Type (0=MS Windows, 1=Linux, 2=Other) [MS Windows ]


The following example shows the initiator rm (remove) command:

iSR6200 <1> (admin) #> initiator rm

Index Status (WWNN,WWPN/iSCSI Name)

----- ------ ----------------------

0 LoggedOut test

1 LoggedOut iqn.1991-05.com.microsoft:qlogic-09sd5i4l

Please select a 'LoggedOut' Initiator from the list above ('q' to quit): 0



Commands

2-28 ISR654601-00 E

iSCSIDiscovers, logs into, and logs out of the specified iSCSI device.


Syntax iscsidiscoverlogin logout

Keywords discover

Discovers a specific iSCSI device.

login

Logs into a specific iSCSI device.

logout

Logs out of a specific iSCSI device.

Examples The following example shows the iscsi discover command:

iSR6200 <1> (admin) #> iscsi discover

A list of attributes with formatting and current values will follow.

Enter a new value or simply press the ENTER key to accept the current value.

If you wish to terminate this process before reaching the end of the list

press 'q' or 'Q' and the ENTER key to do so.

IP Address (IPv4 or IPv6) [0.0.0.0 ] 10.3.5.6

TCP Port No. [3260 ]

Outbound Port (1=GE1, 2=GE2, ...) [GE1 ]

Target CHAP (0=Enable, 1=Disable) [Disabled ]

The following example shows the iscsi logout command:

iSR6200 <1> #> iscsi logout






----- ----------------------


Commands

ISR654601-00 E 2-29

0 iqn.2001-05.com.equallogic:0-8a0906-0aca53601-cd01c5a39984d7dc-isr6152-lun-3

Please select a Target from the list above ('q' to quit): 0

Index IP Address

----- ----------

0 20.20.20.2

Please select a IP Address from the list above ('q' to quit): 0



iSCSI Logout for selected target was successful

The following example shows the iscsi login command:

iSR6200 <1> #> iscsi login






----- ----------------------

0 iqn.2001-05.com.equallogic:0-8a0906-0aca53601-cd01c5a39984d7dc-isr6152-lun-3


Index IP Address

----- ----------

0 20.20.20.2

Please select a IP Address from the list above ('q' to quit): 0



Header Digest (0=Enable, 1=Disable) [Disabled ]

Data Digest (0=Enable, 1=Disable) [Disabled ]

iSCSI Login for selected target was successful


Commands

2-30 ISR654601-00 E

LogoutExits the CLI and returns you to the login prompt.

Authority None

Syntax logout

Examples The following example shows the logout command:

iSR6200 <1> (admin) #> logout

(none) login:


Commands

ISR654601-00 E 2-31

LUN iSCSI Global MapMaps an iSCSI LUN to an initiator, or removes an iSCSI LUN mapping from an initiator.


Syntax lunigmapaddrm

Keywords add

Maps a iSCSI LUN to an initiator using global mapping.

rm

Removes the mapping of a iSCSI LUN from an initiator.

Examples The following example shows the lunigmap add command:

iSR6200 <1> (admin) #> lunigmap add

WARNING

-------

This command should be used to present iSCSI targets that present one LUN per target.

Index Type Mapped (WWNN,WWPN/iSCSI Name)

----- ---- ------ ----------------------

0 FC No 20:00:00:05:1e:b4:45:fb,10:00:00:05:1e:b4:45:fb

1 FC No 50:01:43:80:01:31:e2:69,50:01:43:80:01:31:e2:68

2 FC Yes 50:06:0b:00:00:1d:1c:fd,50:06:0b:00:00:1d:1c:fc

3 FC Yes 20:00:00:e0:8b:89:17:03,21:00:00:e0:8b:89:17:03

4 FC Yes 50:06:0b:00:00:c1:73:75,50:06:0b:00:00:c1:73:74

5 FC Yes 50:01:10:a0:00:17:60:69,50:01:10:a0:00:17:60:68



----- ----------------------

0 iqn.2001-05.com.equallogic:0-8a0906-188701d01-441d4ed3d014cece-pramod-4

1 iqn.2001-05.com.equallogic:0-8a0906-4de701d01-8b9d4ed3d0d4cee3-pramod-5

2 iqn.2001-05.com.equallogic:0-8a0906-33c701d01-5e5d4ed3d104cee4-pramod-6

3 iqn.2001-05.com.equallogic:0-8a0906-d11a53601-e641c5a3cc54db53-pramod-dml



Commands

2-32 ISR654601-00 E

Index (VpGroup Name)

----- --------------

1 VPGROUP_1

Multiple VpGroups are currently 'ENABLED'.

Please select a VpGroup from the list above ('q' to quit): 1

Index (LUN/VpGroup) Serial Number/WWULN

----- ------------- -------------------

0 0/VPGROUP_1 6090A018D0018718CECE14D0D34E1D44

60:90:a0:18:d0:01:87:18:ce:ce:14:d0:d3:4e:1d:44

Please select a LUN to present to the initiator ('q' to quit): 0

Please Assign a ID which maps the initiator to the LUN: [0 ]:

All attribute values that have been changed will now be saved.

Use the targetmap add command with VPGroup Global for presenting the target.

The following example shows the lunigmap rm command:

iSR6200 <1> (admin) #> lunigmap rm


----- ----------------------

0 50:00:1f:e1:50:0a:e1:40,50:00:1f:e1:50:0a:e1:48

1 50:00:1f:e1:50:0a:e1:40,50:00:1f:e1:50:0a:e1:4c

2 50:00:1f:e1:50:0a:37:10,50:00:1f:e1:50:0a:37:18

3 50:00:1f:e1:50:0a:37:10,50:00:1f:e1:50:0a:37:1c

4 50:06:01:60:c1:e0:49:2e,50:06:01:62:41:e0:49:2e

5 50:06:01:60:c1:e0:49:2e,50:06:01:6a:41:e0:49:2e

6 50:0a:09:80:88:cd:63:f5,50:0a:09:81:88:cd:63:f5

7 50:0a:09:80:88:cd:63:f5,50:0a:09:81:98:cd:63:f5

8 iqn.2001-05.com.equallogic:0-8a0906-188701d01-441d4ed3d014cece-pramod-4

9 iqn.2001-05.com.equallogic:0-8a0906-4de701d01-8b9d4ed3d0d4cee3-pramod-5

10 iqn.2001-05.com.equallogic:0-8a0906-33c701d01-5e5d4ed3d104cee4-pramod-6

11 iqn.2001-05.com.equallogic:0-8a0906-d11a53601-e641c5a3cc54db53-pramod-dml



----- --------------

1 VPGROUP_1


Commands

ISR654601-00 E 2-33

2 VPGROUP_2

3 VPGROUP_3

4 VPGROUP_4




----- ------------- -------------------

0 0/VPGROUP_2 PB5A8C3AATK8BW

50:00:1f:e1:50:0a:e1:40


60:05:08:b4:00:10:6b:ac:00:02:d0:00:00:59:00:00


60:05:08:b4:00:10:6b:ac:00:02:d0:00:00:5c:00:00


60:05:08:b4:00:10:6b:ac:00:02:d0:00:00:5f:00:00


60:05:08:b4:00:07:59:a4:00:02:e0:00:07:15:00:00


60:05:08:b4:00:07:59:a4:00:02:e0:00:07:18:00:00

Please select a LUN presented to the initiator ('q' to quit): 0

Index MappedId Type Initiator

----- -------- ---- ---------

0 0 FC 50:06:0b:00:00:c1:73:75

1 0 FC 50:01:10:a0:00:17:60:69

2 0 FC 20:00:00:05:1e:b4:45:fb

Please select an Initiator to remove ('a' to remove all, 'q' to quit): 2



Commands

2-34 ISR654601-00 E

LUN MaskMaps a target LUN to an initiator, and also removes mappings. The CLI prompts you to select from a list of virtual port groups, targets, LUNs and initiators.


Syntax lunmaskadd remove

Keywords add

Maps a LUN to an initiator. After you enter the command, the CLI displays a series of prompts from which you choose the initiator, target, and LUN from lists of existing devices.

remove

Removes the mapping of a LUN from an initiator. After you enter the command, the CLI displays a series of prompts from which you choose the initiator, target, and LUN from lists of existing devices.

Examples The following example shows the lunmask add command:

iSR6200 <1> (admin) #> lunmask add

Index (WWNN/iSCSI Name)

----- -----------------




----- ----------------------

0 20:00:00:20:37:fd:8b:ab,22:00:00:20:37:fd:8b:ab

1 20:00:00:20:37:fd:8a:b0,22:00:00:20:37:fd:8a:b0

2 20:00:00:20:37:fd:9c:f7,22:00:00:20:37:fd:9c:f7

3 20:00:00:20:37:fd:8d:00,22:00:00:20:37:fd:8d:00


LUN WWULN Vendor

---- ---------- --------

0 20:00:00:20:37:fd:8b:ab:00:00:00:00:fc:b7:3f:fa SEAGATE



Commands

ISR654601-00 E 2-35


The following shows an example of the lunmask add command with virtual port groups:


Index Mapped (WWNN,WWPN/iSCSI Name)

----- ------ ----------------------

0 Yes iqn.1991-05.com.microsoft:winhaz38



----- --------------

1 VPGROUP_1

2 VPGROUP_2

3 VPGROUP_3

4 VPGROUP_4




----- ----------------------

0 50:06:01:60:c1:e0:0d:a2,50:06:01:60:41:e0:0d:a2

1 50:06:01:60:c1:e0:0d:a2,50:06:01:68:41:e0:0d:a2


Index (LUN/VpGroup) Vendor

----- ------------- ------

1 1/VPGROUP_1 DGC

2 2/VPGROUP_1 DGC

3 3/VPGROUP_1 DGC




Commands

2-36 ISR654601-00 E

The following example shows the lunmask rm (remove) command:

iSR6200 <1> (admin) #> lunmask rm


----- ----------------------

0 20:00:00:20:37:fd:8b:ab,22:00:00:20:37:fd:8b:ab

1 20:00:00:20:37:fd:8a:b0,22:00:00:20:37:fd:8a:b0

2 20:00:00:20:37:fd:9c:f7,22:00:00:20:37:fd:9c:f7

3 20:00:00:20:37:fd:8d:00,22:00:00:20:37:fd:8d:00


LUN WWULN Vendor

---- ---------- --------

0 20:00:00:20:37:fd:8b:ab:00:00:00:00:fc:b6:1f:fa SEAGATE

Please select a LUN from the list above ('q' to quit): 0

Index Initiator

----- -----------------




The following shows an example of the lunmask rm command with virtual port groups:

iSR6200 <1> (admin) #> lunmask rm


----- ----------------------

0 50:06:01:60:c1:e0:0d:a2,50:06:01:60:41:e0:0d:a2

1 50:06:01:60:c1:e0:0d:a2,50:06:01:68:41:e0:0d:a2


Index (LUN/VpGroup) Vendor

----- ------------- ------

0 0/VPGROUP_1 DGC

1 1/VPGROUP_1 DGC

2 2/VPGROUP_1 DGC

3 3/VPGROUP_1 DGC


Commands

ISR654601-00 E 2-37

4 0/VPGROUP_2 DGC


Index Initiator

----- -----------------

0 iqn.1991-05.com.microsoft:winhaz38



iSR6200 <1> (admin) #>


Commands

2-38 ISR654601-00 E

LUN RemapMaps a target LUN mapping to an initiator, or removes a target LUN mapping from an initiator where the LUN ID is remapped.


Syntax lunremapaddrm

Keywords add

Maps a LUN to an initiator with any different LUN ID.

rm

Removes the mapping of a LUN from an initiator.

Examples The following example shows the lunremap add command:

iSR6200 <1> (admin) #> lunremap add


----- ---- ------ ----------------------

0 FC No 20:00:00:e0:8b:1d:73:63,21:00:00:e0:8b:1d:73:63

1 FC Yes 20:01:00:1b:32:31:12:79,21:01:00:1b:32:31:12:79



----- ----------------------

0 20:00:00:11:c6:17:0f:02,21:00:00:11:c6:17:0f:02

1 20:00:00:11:c6:17:12:77,21:00:00:11:c6:17:12:77

2 20:00:00:11:c6:17:0f:11,21:00:00:11:c6:17:0f:11

3 20:00:00:11:c6:17:0f:07,21:00:00:11:c6:17:0f:07

4 20:00:00:11:c6:17:0e:d9,21:00:00:11:c6:17:0e:d9

5 20:00:00:11:c6:17:18:3e,21:00:00:11:c6:17:18:3e

6 20:00:00:11:c6:17:0f:0f,21:00:00:11:c6:17:0f:0f

7 20:00:00:11:c6:17:0e:c6,21:00:00:11:c6:17:0e:c6



----- --------------

1 VPGROUP_1


Commands

ISR654601-00 E 2-39




----- ------------- -------------------

0 0/VPGROUP_1 3KQ015PK000075091D8W

20:00:00:11:c6:17:0f:07


Please Assign a ID which maps the initiator to the LUN: [0 ]: 5


Use the targetmap add command with VPGroup Global for presenting the target.

The following example shows the lunremap rm command:

iSR6200 <1> (admin) #> lunremap rm


----- ----------------------

0 50:05:07:68:02:00:0f:03,50:05:07:68:02:10:0f:03

1 50:05:07:68:02:00:0f:02,50:05:07:68:02:10:0f:02

2 20:00:00:11:c6:17:0f:02,21:00:00:11:c6:17:0f:02

3 20:00:00:11:c6:17:12:77,21:00:00:11:c6:17:12:77

4 20:00:00:11:c6:17:0f:11,21:00:00:11:c6:17:0f:11

5 20:00:00:11:c6:17:0f:07,21:00:00:11:c6:17:0f:07

6 20:00:00:11:c6:17:0e:d9,21:00:00:11:c6:17:0e:d9

7 20:00:00:11:c6:17:18:3e,21:00:00:11:c6:17:18:3e

8 20:00:00:11:c6:17:0f:0f,21:00:00:11:c6:17:0f:0f

9 20:00:00:11:c6:17:0e:c6,21:00:00:11:c6:17:0e:c6



----- ------------- -------------------

0 0/VPGROUP_1 3KQ0161400007514H3QK

20:00:00:11:c6:17:12:77

Please select a LUN presented to the initiator ('q' to quit): 0

Index MappedId Type Initiator

----- -------- ---- ---------

0 2 FC 20:01:00:1b:32:31:12:79


Commands

2-40 ISR654601-00 E




Commands

ISR654601-00 E 2-41

PasswordChanges the guest and administrator passwords.


Syntax passwd

Examples The following example shows the passwd command:

iSR6200 <1> (admin) #> passwd

Press 'q' and the ENTER key to abort this command.

Select password to change (0=guest, 1=admin) : 1

account OLD password : ******

account NEW password (6-128 chars) : ******

please confirm account NEW password : ******

Password has been changed.


Commands

2-42 ISR654601-00 E

PingVerifies the connectivity of management and GE ports. This command works with both IPv4 and IPv6.


Syntax ping

Examples The following example shows the ping command:

iSR6200 <1> (admin) #> ping


IP Address (IPv4 or IPv6) [0.0.0.0] fe80::217:a4ff:fe99:c279

Iteration Count (0=Continuously) [0 ] 10

Outbound Port (0=Mgmt, 1=GE1, 2=GE2, ...) [Mgmt ]

Size Of Packet (Min=1, Max=65486 Bytes) [56 ]

Pinging fe80::217:a4ff:fe99:c279 with 56 bytes of data:

Request timed out.

Reply from fe80::217:a4ff:fe99:c279: bytes=64 time=0.4ms









Ping Statistics for fe80::217:a4ff:fe99:c279:

Packets: Sent = 10, Received = 9, Lost = 1

Approximate round trip times in milli-seconds:

Minimum = 0.2ms, Maximum = 0.7ms, Average = 0.3ms


Commands

ISR654601-00 E 2-43

QuitExits the CLI and returns you to the login prompt. (Same as the exit command.)

Authority None

Syntax quit

Examples The quit command behaves differently depending on whether you at the chassis or blade management level.

At the chassis management level, quit returns you to the login prompt. The following example shows the quit command for the chassis:

iSR6200 <1> (admin) #> quit

(none) login:

At the blade management level, quit returns you to the chassis management level. The following example shows the quit command for the blade:

iSR6200 <1> (admin) #> quit

iSR6200 #>


Commands

2-44 ISR654601-00 E

RebootRestarts the blade firmware.


Syntax reboot

Examples The following example shows the reboot command:

iSR6200 <1> (admin) #> reboot

Are you sure you want to reboot the System (y/n): y

System will now be rebooted...


Commands

ISR654601-00 E 2-45

Remote MappingsMaps an initiator and target, one of which is located on a remote system (router). After you enter this command, it prompts you to enter the remote system (router), and then lists the devices (initiators and targets) located on the remote system. You can select a device from the remote system and then the local system.


Syntax remotemapaddmodrm

Keywords add

Adds a device mapping, initiator to target, one of which is remote.

mod

Modifies an existing remote device mapping.

rm

Removes a remote device mapping.

Examples The following example shows the remotemap add command:

iSR6200 <1> (admin) #> remotemap add

The following wizard will create a mapping a device connected to the

local system and a device connected to the selected remote peer system.

If you wish to terminate this wizard before reaching the end of the list


Index (Symbolic Name/Serial Number)

----- -----------------------------

0 iSR6200(1047J00014)

Please select a REMOTE system from the list above ('q' to quit) : 0


----- ----------------------

0 50:06:01:60:cb:a0:35:f6,50:06:01:69:4b:a0:35:f6

1 50:06:01:60:cb:a0:35:f6,50:06:01:61:4b:a0:35:f6

Please select a LOCAL device from the list above ('q' to quit) : 0



Commands

2-46 ISR654601-00 E

----- ----------------------

0 50:01:10:a0:00:17:60:11,50:01:10:a0:00:17:60:10

1 50:01:10:a0:00:17:60:11,50:01:10:a0:00:17:60:12

Please select a REMOTE device from the list above ('q' to quit) : 1

Smart-Write (0=Enable, 1=Disable) [Enabled ]

Smart-Write Compression (0=Enable, 1=Disable) [Disabled ]

Smart-Write Load Balance (0=Enable, 1=Disable) [Disabled ]


The following example shows the remotemap mod command:

iSR6200 <1> (admin) #> remotemap mod

The following wizard will be used to modify various settings of

a remote mapping. If you wish to terminate this wizard before reaching

the end of the list press 'q' or 'Q' and the ENTER key to do so.

Index Local Device (WWPN) Remote Device (WWPN)

----- ------------------- --------------------

0 50:06:01:61:4b:a0:35:f6 50:01:10:a0:00:17:60:10

1 50:06:01:69:4b:a0:35:f6 50:01:10:a0:00:17:60:12

Please select a remote mapping from the list above ('q' to quit): 1

Smart-Write (0=Enable, 1=Disable) [Enabled ]

Smart-Write Compression (0=Enable, 1=Disable) [Disabled ] 0

Smart-Write Load Balance (0=Enable, 1=Disable) [Disabled ] 0


The following example shows the remotemap rm command:

iSR6200 <1> (admin) #> remotemap rm

The following wizard will query for attributes before persisting

and activating the updated mapping in the system configuration.



Index Local Device (WWPN) Remote Device (WWPN)

----- ------------------- --------------------

0 50:06:01:61:4b:a0:35:f6 50:01:10:a0:00:17:60:10


Commands

ISR654601-00 E 2-47

1 50:06:01:69:4b:a0:35:f6 50:01:10:a0:00:17:60:12

Please select a remote mapping from the list above ('q' to quit): 1



Commands

2-48 ISR654601-00 E

Remote PeersLets you assign a router peer to a local router, which can have up to four peers.


Syntax remotepeeraddmodrm

Keywords add

Creates a peer router.

mod

Allows you to modify the iSCSI connections for a remote system peer router.

rm

Deletes a peer router.

Examples The following example shows the remotepeer add command:

iSR6200 <1> (admin) #> remotepeer add





PEER MGMT port address (IPv4 or IPv6) [0.0.0.0] 172.35.15.178

Contacting PEER system (timeout=120 seconds) ...

<Admin> password of PEER system: ******

<Admin> password confirmed.

Remote System Information

-------------------------


Symbolic Name iSR6200

Serial Number 1047J00014

No. of iSCSI Ports 4

iSCSI Base Name iqn.2004-08.com.qlogic:isr6152.1047j00014

Mgmt IPv4 Address 172.35.15.178

iSCSI Port 1 IPv4 Address 10.10.10.178


Commands

ISR654601-00 E 2-49

iSCSI Port 1 IPv6 Link-Local fe80::2c0:ddff:fe1e:a740





Please select an ISCSI IP Address from REMOTE system above(IPv4 or IPv6) [0.0.0.0 ] 10.10.10.178







Please select an ISCSI IP Address from LOCAL system above(IPv4 or IPv6) [0.0.0.0 ] 10.10.10.177

Do you wish to add another ISCSI connection to the REMOTE system (y/n): n

Connect to Remote System iSR6200(1047J00014) using connection(s):

0) 10.10.10.177(LOCAL) to 10.10.10.178(REMOTE)

Do you wish to add the REMOTE system above (y/n): y


The following example shows the remotepeer mod command:

iSR6200 <1> (admin) #> remotepeer mod


----- -----------------------------

0 iSR6200(1047J00014)

Please select a remote system from the list above ('q' to quit): 0

Remote System Information

-------------------------








Commands

2-50 ISR654601-00 E

Mgmt IPv6 Link-Local ::

Mgmt IPv6 Address 1 ::


No. of iSCSI Remote Connections 1

Remote iSCSI Connection Address 1 10.10.10.178 through 10.10.10.177

Do you wish to modify the iSCSI connections for the REMOTE system above? (y/n): y















Do you wish to add another ISCSI connection to the REMOTE system (y/n): y














Commands

ISR654601-00 E 2-51



Connect to Remote System iSR6200(1047J00014) using connection(s):

0) 20.20.20.177(LOCAL) to 20.20.20.178(REMOTE)

1) 10.10.10.177(LOCAL) to 10.10.10.178(REMOTE)

Modifying the remote system may cause the loss of connection to

the remote system and any remote mappings assocated with it.

Do you wish to modify the REMOTE system (y/n): y


The following example shows the remotepeer rm command:

iSR6200 <1> (admin) #> remotepeer rm


----- -----------------------------

0 iSR6200(1047J00014)

Please select a remote system from the list above ('q' to quit): 0



Commands

2-52 ISR654601-00 E

ResetRestores the router configuration parameters to the factory-default values.

The reset factory command deletes all LUN mappings, as well as all persistent data regarding targets, LUNs, initiators, virtual port group settings, log files, iSCSI and MGMT IP addresses, Fibre Channel and Ethernet port statistics, and passwords. This command also restores the factory default IP addresses.

The reset mappings command clears only the LUN mappings.


Syntax resetfactorymappings

Examples The following example shows the reset factory command:

iSR6200 <1> (admin) #> reset factory

Are you sure you want to restore to factory default settings (y/n): y

Please reboot the System for the settings to take affect.

The following example shows the reset mappings command:

iSR6200 <1> (admin) #> reset mappings

Are you sure you want to reset the mappings in the system (y/n): y

Please reboot the System for the settings to take affect.


Commands

ISR654601-00 E 2-53

SaveSaves logs, traces, and port statistics.


Syntax savecapturelogs tracesportstats

Keywords capture

The save capture command creates a debug file that captures all debug dump data. After the command completes, you must FTP the debug capture file from the blade.

logs

The save logs command creates a tar file that contains the router’s log data, storing the file in the router’s /var/ftp directory. After the command completes, you must FTP the log’s tar file from the blade.

traces

The save traces command creates a tar file that contains the router’s dump data, storing the tar file in the router’s /var/ftp directory. After the command completes, you must FTP the trace’s tar file from the blade. After executing this command, the system notifies you if the router does not have any dump data. Each time it generates dump data, the system adds an event log entry.

portstats

The save portstats command saves the Fibre Channel or GbE port statistics in a CSV file format in the /var/ftp directory. After the command is complete, you must FTP the file from the blade.

Examples The following example shows the save capture command:

iSR6200 <1> (admin) #> save capture

Debug capture completed. Package is System_Capture.tar.gz


The following example shows the save logs command:

iSR6200 <1> (admin) #> save logs

Save Event Logs completed. Package is Router_Evl.tar.gz



Commands

2-54 ISR654601-00 E

The following example shows the save traces command:

iSR6200 <1> (admin) #> save traces

Save ASIC Traces completed. Package is Router_Asic_Trace.tar.gz


The following examples show the save portstats command for both a Fibre Channel and a GbE port:

iSR6200 <1> (admin) #> save portstats fc 1

Fc Port 1 statistics are successfully stored at /var/ftp/fcMonStats1.csv

Please FTP to get the statistics file.

iSR6200 <1> (admin) #> save portstats gige 1

Gige Port 1 statistics are successfully stored at /var/ftp/gigeMonStats1.csv

Please FTP to get the statistics file.


Commands

ISR654601-00 E 2-55

SetConfigures general router parameters, as well as parameters that are specific to the Fibre Channel, iSCSI, and management ports.


Syntax setaliaschapchassisevent_notificationfc [ <PORT_NUM> ]featuresiscsi [ <PORT_NUM> ]isnsmgmtntppropertiessnmp [trap_destinations [ <DEST_NUM> ]]systemvpgroups [vpgroup index]

Keywords alias

Assigns alias name to a presented iSCSI target. (See “Set Alias” on page 2-57.)

chap

Sets the CHAP secrets. (See “Set CHAP” on page 2-59.)

chassis

Sets the chassis name. (See “Set Chassis” on page 2-60.)

event_notification

Sets the event notification mechanism and destination. (See “Set Event Notification” on page 2-61.)

fc [ <PORT_NUM> ]

Sets the Fibre Channel port parameters. (See “Set FC” on page 2-62.)

features

Applies license keys to the router. (See “Set Features” on page 2-63.)


Commands

2-56 ISR654601-00 E

iscsi [ <PORT_NUM> ]

Sets the iSCSI port parameters. (See “Set iSCSI” on page 2-64.)

isns

Sets the Internet simple name service (iSNS) parameters. (See “Set iSNS” on page 2-65.)

mgmt

Sets the management port parameters. (See “Set MGMT” on page 2-66.)

ntp

Sets the network time protocol (NTP) parameters. (See “Set NTP” on page 2-68.)

properties

Configures CLI properties for the blade. (See “Set Properties” on page 2-69.)

snmp [trap_destinations [ <DEST_NUM> ]]

Sets the simple network management protocol (SNMP) parameters. (See “Set SNMP” on page 2-70.)

system

Sets system parameters such as symbolic name and log level. (See “Set System” on page 2-72.)

vpgroups [vpgroup index]

Sets virtual port groups (VPGs) on the blade. (See “Set VPGroups” on page 2-73.)


Commands

ISR654601-00 E 2-57

Set AliasAllows an alias name to be assigned to a presented iSCSI target.


Syntax set alias

Examples The following example shows the set alias command. The example also shows the results of this command using the show presented_targets command:

iSR6200 <2> (admin) #> set alias






----- ----------------------

0 iqn.2004-08.com.qlogic:isr6200.0823e00010.b2.01.50001fe150069d2c

1 iqn.2004-08.com.qlogic:isr6200.0823e00010.b2.01.50001fe150069d29

2 iqn.2004-08.com.qlogic:isr6200.0823e00010.b2.01.50001fe150069d2d

3 iqn.2004-08.com.qlogic:isr6200.0823e00010.b2.01.50001fe150069d28

Please select a iSCSI node from the list above ('q' to quit): 0





Alias (Max=255 Characters, 0=Emtpy String) [ ] FirstTarget


iSR6200 <2> (admin) #> show presented_targets

Presented Target Information

------------------------------

iSCSI Presented Targets

-------------------------

Name iqn.2004-08.com.qlogic:isr6200.0823e00010.b2.01.50001fe150069d2c

Alias FirstTarget


Commands

2-58 ISR654601-00 E

<MAPS TO>

WWNN 50:00:1f:e1:50:06:9d:20

WWPN 50:00:1f:e1:50:06:9d:2c

Name iqn.2004-08.com.qlogic:isr6200.0823e00010.b2.01.50001fe150069d29

Alias

<MAPS TO>

WWNN 50:00:1f:e1:50:06:9d:20

WWPN 50:00:1f:e1:50:06:9d:29

Name iqn.2004-08.com.qlogic:isr6200.0823e00010.b2.01.50001fe150069d2d

Alias

<MAPS TO>

WWNN 50:00:1f:e1:50:06:9d:20

WWPN 50:00:1f:e1:50:06:9d:2d

Name iqn.2004-08.com.qlogic:isr6200.0823e00010.b2.01.50001fe150069d28

Alias

<MAPS TO>

WWNN 50:00:1f:e1:50:06:9d:20

WWPN 50:00:1f:e1:50:06:9d:28


Commands

ISR654601-00 E 2-59

Set CHAPProvides for the configuration of the challenge handshake authentication protocol (CHAP). For configuration details, see 3 Configuring CHAP.


Syntax set chap

Examples The following example shows the set chap command:

iSR6200 <1> (admin) #> set chap


Index iSCSI Name

----- ----------

0 iqn.2004-08.com.qlogic:iSR6200:test.0

1 iqn.2004-08.com.qlogic:iSR6200:test.1


3 iqn.2004-08.com.qlogic:iSR6200:test.0.20000014c3449afa.22000014c3449afa

Please select a presented target from the list above ('q' to quit): 2


Enter a new value or simply press the ENTER key to accept the current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so.

CHAP (0=Enable, 1=Disable) [Disabled] 0

CHAP Secret (Max = 100 characters) [ ] ****



Commands

2-60 ISR654601-00 E

Set ChassisSets the chassis name.


Syntax set chassis

Examples The following example shows the set chassis command:

iSR6200 <1> (admin) #> set chassis





Chassis Name (Max = 64 characters) [ ] rack 14



Commands

ISR654601-00 E 2-61

Set Event NotificationSets the system notification on or off, and specifies the URL to notify.


Syntax set event_notification

Examples The following example shows the set event notification command:

iSR6200 <1> (admin) #> set event_notification





Notification (0=Enable, 1=Disable) [Disabled ] 0

Notification Method (1=HTTP) [HTTP ]

URL [ ] www.abcdefg.xyz



Commands

2-62 ISR654601-00 E

Set FCConfigures a Fibre Channel port.


Syntax set fc [ <PORT_NUM> ]

Keywords [ <PORT_NUM> ]

The number of the Fibre Channel port to be configured.

Examples The following example shows the set fc command:

iSR6200 <1> (admin) #> set fc



WARNING:

The following command might cause a loss of connections to both ports.

Configuring FC Port: 1

-------------------------

Link Rate (0=Auto, 1=1Gb, 2=2Gb) [Auto ]

Frame Size (0=512B, 1=1024B, 2=2048B) [2048 ]

Execution Throttle (Min=16, Max=256) [64 ]

Programmed Connection Option:

(0=Loop Only, 1=P2P Only, 2=Loop Pref) [Loop Pref ]

All attribute values for Port 1 that have been changed will now be saved.

Configuring FC Port: 2

-------------------------

Link Rate (0=Auto, 1=1Gb, 2=2Gb) [Auto ]

Frame Size (0=512B, 1=1024B, 2=2048B) [2048 ]

Execution Throttle (Min=16, Max=256) [64 ]

Programmed Connection Option:

(0=Loop Only, 1=P2P Only, 2=Loop Pref) [Loop Pref ]



Commands

ISR654601-00 E 2-63

Set FeaturesApplies license keys to the router. The date and time must be set on the router prior to applying a new feature key.


Syntax set features

Keywords None.

Examples The following example shows the set features command:

iSR6200 <1> (admin) #> set features





Enter feature key to be saved/activated: 1-LCURGL0FHDGQI-ISR6200-SW

Feature Key is added to the blade.



Commands

2-64 ISR654601-00 E

Set iSCSIConfigures an iSCSI port.


Syntax set iscsi [ <PORT_NUM> ]

Keywords [ <PORT_NUM> ]

The number of the iSCSI port to be configured.

Examples The following example shows the set iscsi command:

iSR6200 <1> (admin) #> set iscsi 1





WARNING:

The following command might cause a loss of connections to both ports.

Configuring iSCSI Port: 1

---------------------------

Port Status (0=Enable, 1=Disable) [Enabled ]

Port Speed (0=Auto, 1=100Mb, 2=1Gb) [Auto ]


Window Size (Min=8124B, Max=1048576B) [65536 ]

IPv4 Address [10.3.5.205 ]

IPv4 Subnet Mask [255.255.255.0 ]

IPv4 Gateway Address [0.0.0.0 ]

IPv4 TCP Port No. (Min=1024, Max=65535) [3260 ]

IPv4 VLAN (0=Enable, 1=Disable) [Disabled ]

IPv6 Address 1 [:: ]

IPv6 Address 2 [:: ]

IPv6 Default Router [:: ]

IPv6 TCP Port No. (Min=1024, Max=65535) [3260 ]

IPv6 VLAN (0=Enable, 1=Disable) [Disabled ]

iSCSI Header Digests (0=Enable, 1=Disable) [Disabled ]

iSCSI Data Digests (0=Enable, 1=Disable) [Disabled ]



Commands

ISR654601-00 E 2-65

Set iSNSConfigures iSNS parameters for a blade.


Syntax set isns

Examples The following example shows the set isns command:

iSR6200 <2> (admin) #> set isns





iSNS (0=Enable, 1=Disable) [Disabled ] 0

iSNS Address (IPv4 or IPv6) [0.0.0.0 ] 10.3.6.33




Commands

2-66 ISR654601-00 E

Set MGMTConfigures the blade’s management port (10/100).


Syntax set mgmt

Examples The following example shows the set mgmt command:

iSR6200 <1> (admin) #> set mgmt


WARNING:

The following command might cause a loss of connections to the MGMT port.

IPv4 Interface (0=Enable, 1=Disable) [Enabled]

IPv4 Mode (0=Static, 1=DHCP, 2=Bootp, 3=Rarp) [Dhcp ]

IPv6 Interface (0=Enable, 1=Disable) [Enabled]

IPv6 Mode (0=Manual, 1=AutoConfigure) [Manual ] 1


The following example shows how to use the set mgmt command to set a static address:

iSR6200 <1> (admin) #> set mgmt





WARNING:

The following command might cause a loss of connections to the MGMT port.

IPv4 Interface (0=Enable, 1=Disable) [Enabled ]

IPv4 Mode (0=Static, 1=DHCP, 2=Bootp, 3=Rarp) [Static ]

IPv4 Address [172.17.136.86 ]

IPv4 Subnet Mask [255.255.255.0 ]

IPv4 Gateway [172.17.136.1 ]


Commands

ISR654601-00 E 2-67

IPv6 Interface (0=Enable, 1=Disable) [Disabled ]



Commands

2-68 ISR654601-00 E

Set NTPConfigures the NTP parameters.


Syntax set ntp

Examples The following example shows the set ntp command:

iSR6200 <1> (admin) #> set ntp





NTP (0=Enable, 1=Disable) [Disabled ] 0

TimeZone Offset from GMT (Min=-12:00,Max=12:00) [00:00 ] -8:0

IP Address [1] (IPv4 or IPv6) [0.0.0.0 ] 207.126.97.57

IP Address [2] (IPv4 or IPv6) [0.0.0.0 ]

IP Address [3] (IPv4 or IPv6) [0.0.0.0 ]



Commands

ISR654601-00 E 2-69

Set PropertiesConfigures CLI properties for the blade.


Syntax set properties

Examples The following example shows the set properties command:

iSR6200 <1> (admin) #> set properties





CLI Inactivty Timer (0=Disable, 1=15min, 2=60min) [15min ]

CLI Prompt (Max=32 Characters) [iSR6200 ]



Commands

2-70 ISR654601-00 E

Set SNMPConfigures the general SNMP properties, as well as configuring eight trap destinations.


Syntax set snmp [trap_destinations [ <DEST_NUM> ]]

Keywords trap_destinations

Specifies the setting of the trap destinations.

Examples The following example shows the set snmp command for setting the general properties:

iSR6200 <1> (admin) #> set snmp



Configuring SNMP :

-----------------

Read Community [ ] Public

Trap Community [ ] Private

System Location [ ]

System Contact [ ]

Authentication Traps (0=Enable, 1=Disable) [Disabled ]


The following example shows configuring an SNMP trap destination:

iSR6200 <1> (admin) #> set snmp trap_destinations



Configuring SNMP Trap Destination 1 :

-------------------------------------

Destination enabled (0=Enable, 1=Disable) [Disabled ] 0

IP Address [0.0.0.0 ] 10.0.0.5


Commands

ISR654601-00 E 2-71

Destination Port [0 ] 1024

Trap Version [0 ] 2


-------------------------------------

Destination enabled (0=Enable, 1=Disable) [Disabled ]


-------------------------------------



-------------------------------------



-------------------------------------



-------------------------------------



-------------------------------------



-------------------------------------




Commands

2-72 ISR654601-00 E

Set SystemConfigures the blade system-wide parameters.


Syntax set system

Examples The following example shows the set system command:

iSR6200 <1> (admin) #> set system





System Symbolic Name (Max = 64 characters) [Blade-1 ]

Target Presentation Mode (0=Auto, 1=Manual) [Auto ]

Lun Mapping (0=Enable, 1=Disable) [Enabled ]

Controller Lun AutoMap (0=Enable, 1=Disable) [Disabled ]

Target Access Control (0=Enable, 1=Disable) [Enabled ]

Telnet (0=Enable, 1=Disable) [Enabled ]

SSH (0=Enable, 1=Disable) [Enabled ]

FTP (0=Enable, 1=Disable) [Enabled ]

System Log Level (Default,Min=0, Max=2) [0 ]

Time To Target Device Offline (Secs,Min=0, Max=120) [0 ] 30

Please reboot the system for these changes to take affect.


Commands

ISR654601-00 E 2-73

Set VPGroupsSets virtual port groups (VPGs) on the blade. Allows you to enable and disable VPGs, and to modify the VPG name.


Syntax set vpgroups [vpgroup index]

Examples The following example shows how to enable virtual port groups 2 and 3:

iSR6200 <1> (admin) #> set vpgroups





Configuring VpGroup: 1

-------------------------

Status (0=Enable, 1=Disable) [Enabled ]

VpGroup Name (Max = 64 characters) [VPGROUP_1 ]

All attribute values for VpGroup 1 that have been changed will now be saved.


-------------------------

Status (0=Enable, 1=Disable) [Disabled ] 0




-------------------------





-------------------------

Status (0=Enable, 1=Disable) [Disabled ]



Commands

2-74 ISR654601-00 E

ShowDisplays blade operational information.

Authority None

Syntax show chapchassisevent_notificationfeature_keysfeaturesfc [port_num]fciproutes [link_id}initiators [fc or iscsi]initiator_lunmaskiostatsiscsi [port_num]isns [port_num]logs [entries]luninfolunslunmaskmemorymgmtntpperf [ byte | init_rbyte | init_wbyte | tgt_rbyte | tgt_wbyte ]portstats <fc | gige> <port-no> <hours | mins> <duration>presented_initiatorspresented_targets [fc or iscsi]propertiesremotemapsremotepeersrpcinfosnmpstatsswdevicestargets [fc or iscsi]systemvpgroups [vpgroup index]


Commands

ISR654601-00 E 2-75

Keywords chap

Displays configured CHAP iSCSI nodes. (See “Show CHAP” on page 2-78.)

chassis

Displays chassis information and status. (See “Show Chassis” on page 2-79.)

event_notification

Displays event notification status (enabled/disabled) and URL. (See “Show Event Notification” on page 2-81.)

fc [port_num]

Displays Fibre Channel port information. (See “Show FC” on page 2-82.)

fciproutes [link_id]

Displays FCIP route confirmation parameters. (See “FCIP Route” on page 2-13.)

feature_keys

Displays license keys for features that require licensing for use. (See “Show Feature Keys” on page 2-84.)

features

Displays licensed features. (See “Show Features” on page 2-85.)

initiators [fc or iscsi]

Displays SCSI initiator information: iSCSI or Fibre Channel. (See “Show Initiators” on page 2-86.)

initiators_lunmask

Displays initiators and the LUNs to which they are mapped. (See “Show Initiators LUN Mask” on page 2-88.)

iostats

Displays statistics of read/write operations for a selected device. (See “Show I/O Statistics” on page 2-89.)

iscsi [port_num]

Displays iSCSI port information and configuration. (See “Show iSCSI” on page 2-90.)

isns [port_num]

Displays the router’s iSNS configuration. (See “Show iSNS” on page 2-94.)

logs

Displays the router’s logging information. (See “Show Logs” on page 2-95.)


Commands

2-76 ISR654601-00 E

luninfo

Displays complete LUN information for a specified target and LUN. (See “Show LUN Info” on page 2-96.)

luns

Displays LUN information and their targets. (See “Show LUNs” on page 2-98.)

lunmask

Displays LUN mappings. (See “Show LUN Mask” on page 2-100.)

memory

Displays memory usage. (See “Show Memory” on page 2-102.)

mgmt

Displays the router’s management port (10/100) configuration. (See “Show MGMT” on page 2-103.)

ntp

Displays the router’s network time protocol (NTP) configuration. (See “Show NTP” on page 2-104.)

perf [ byte | init_rbyte | init_wbyte | tgt_rbyte | tgt_wbyte ]

Displays router performance. (See “Show Performance” on page 2-105.)

portstats <fc | gige> <port-no> <hours | mins> <duration>

Displays Fibre Channel or GbE port statistics. (See “Show Port Statistics” on page 2-108.)

presented_targets [fc or iscsi]

Displays targets presented by the router: Fibre Channel, iSCSI, or both. (See “Show Presented Targets” on page 2-112.)

properties

Displays router properties. (See “Show Properties” on page 2-115.)

snmp

Displays the router’s simple network management protocol (SNMP) properties and trap configurations. (See “Show SNMP” on page 2-120.)

stats

Displays the router statistics, both Fibre Channel and iSCSI. (See “Show Stats” on page 2-121.)


Commands

ISR654601-00 E 2-77

swdevice

Displays the port names of Fibre Channel devices (initiators and targets) that can be remotely mapped using SmartWriteTM. (See “Show SmartWrite Devices” on page 2-119.)

system

Displays router product information including serial number, software version, hardware version, configuration, and temperature. (See “Show System” on page 2-128.)

targets [fc or iscsi]

Displays targets discovered by the router: Fibre Channel, iSCSI, or both. (See “Show Targets” on page 2-129.)

vpgroups [vpgroup index]

Displays virtual port groups. (See “Show VPGroups” on page 2-131.)


Commands

2-78 ISR654601-00 E

Show CHAPDisplays CHAP configuration for iSCSI nodes.

Authority None

Syntax show chap

Examples The following example shows the show chap command:

iSR6200 <1> (admin) #> show chap

The following is a list of iSCSI nodes that have been configured with CHAP 'ENABLED':

Type iSCSI Node

-------- ------------

Init iqn.1991-05.com.microsoft:qlogic-09sd5i4l


Commands

ISR654601-00 E 2-79

Show ChassisDisplays the chassis information and status. This command can be executed from the chassis or blade level.

Authority None

Syntax show chassis

Examples The following example shows the show chassis command:

iSR6200 #> show chassis

Chassis Information

---------------------

Product Name ISR6200

Chassis Name Router Chassis Name Here



Fan Speed Normal

Blade 1 Information (Left Slot)

-------------------------------

Status Online





SW Version 3.3.0.0



----------------------

Status Installed



Blade 2 Information (Right Slot)

--------------------------------

Status Online






Commands

2-80 ISR654601-00 E

SW Version 3.3.0.0



----------------------

Status Installed

Power Source Not Connected



Commands

ISR654601-00 E 2-81

Show Event NotificationDisplays event notification status (enabled or disabled) and URL (IP address).

Authority None

Syntax show event_notification

Examples The following example shows the show event_notification command:

iSR6200 <1> #> show event_notification

EventNotification Info

----------------------

Http Enabled

Url 172.17.136.68


Commands

2-82 ISR654601-00 E

Show FCDisplays Fibre Channel port information for the specified port. If you do not specify a port, this command displays all ports.

Authority None

Syntax show fc [port_num]

Keywords [port_num]

Identifies the number of the Fibre Channel port to display.

Examples The following example shows the show fc command:

iSR6200 <1> #> show fc 2

FC Port Information

---------------------

FC Port FC2

Port Status Enabled

Port Mode FCP

Link Status Up

Current Link Rate 8Gb

Programmed Link Rate Auto

WWNN 20:00:00:c0:dd:12:cd:92 (VPGROUP_1)

WWPN 21:00:00:c0:dd:12:cd:92 (VPGROUP_1)

Port ID 7e-04-ef (VPGROUP_1)



Port ID 7e-04-e8 (VPGROUP_2)







Firmware Revision No. 5.03.14

Frame Size 2048

Execution Throttle 256

Connection Mode Loop

Programmed Connection Option Loop Preferred

SFP Type 8Gb


Commands

ISR654601-00 E 2-83

Show FCIP RoutesDisplays FCIP route configuration parameters.

Authority None

Syntax show fciproutes [link_id]

Keywords [link_id]

Specifies the number of the FCIP route to be displayed (1 or 2).

Examples The following example shows the show fciproutes command.

iSR6200 <2> #> show fciproutes

FCIP Route Information

------------------------

FCIP Route 1

FCIP Interfaces Status Enabled

FCIP Link Status Down

FC Port FC1

GE Port GE1

GE Link Status Up

Local IP Address 172.35.15.11

Remote IP Address 172.17.136.18

Subnet Mask 255.255.254.0

Gateway IP Address 0.0.0.0

MTU Size Normal

TCP Window Size 32768

Window Scaling Enabled

Window Scaling Factor 7

TCP Port No 3225

Current GE Port Speed 1Gb/FDX

Programmed GE Port Speed Auto

Bandwidth, Mbit/sec 1000

VLAN Disabled

FCIP SW Compression Auto


Commands

2-84 ISR654601-00 E

Show Feature KeysLists the features currently licensed for the router, the license key for each, and the date the license was applied.

Authority None

Syntax show feature_keys

Examples The following example shows the show feature_keys command.

iSR6200 <1> #> show feature_keys

Feature Key Information

-------------------------

Key 1-LC4CNWGC4WZJW-SMART-WRITE (SmartWrite 1GbE)

Date Applied Wed Mar 9 11:45:53 2011

Key 100000-LCRWFT4U0I3GI-DM-2TB (Data Migration 2TB)

Date Applied Thu Jun 23 16:42:34 2011


Commands

ISR654601-00 E 2-85

Show FeaturesDisplays any features that have been licensed.

Authority None

Syntax show features

Examples The following examples shows the show features command.

iSR6200 <1> #> show features

License Information

-------------------

FCIP 1Gig Licensed

FCIP 10Gig Licensed

DM Capacity Licensed

DM Array Licensed

DS Capacity Licensed

DS Array Licensed


Commands

2-86 ISR654601-00 E

Show InitiatorsDisplays SCSI initiator information for Fibre Channel, iSCSI, or both.

Authority None

Syntax show initiatorsfc iscsi

Keywords fc

Specifies the display of Fibre Channel initiators.

iscsi

Specifies the display of iSCSI initiators.

Examples The following example shows the show initiators command:

iSR6200 <1> #> show initiators

WWNN 20:00:00:e0:8b:88:b6:02

WWPN 21:00:00:e0:8b:88:b6:02

Port ID 01-00-00

Status Logged In

Type FC

OS Type Other

WWNN 20:01:00:e0:8b:a8:b6:02

WWPN 21:01:00:e0:8b:a8:b6:02

Port ID 00-00-00

Status Logged Out

Type FC

OS Type Windows

Initiator Name iqn.1991-05.com.microsoft:qlogic-1

Alias

IP Address 0.0.0.0

Status Logged Out

Type ISCSI

OS Type Windows

Initiator Name iqn.1991-05.com.microsoft:qlogic-2

Alias

IP Address 0.0.0.0


Commands

ISR654601-00 E 2-87

Status Logged Out

Type ISCSI

OS Type Windows


Commands

2-88 ISR654601-00 E

Show Initiators LUN MaskDisplays all LUNs mapped to a user-selected initiator.

Authority None

Syntax show initiators_lunmask

Examples The following example shows the show initiators_lunmask command:

iSR6200 <1> #> show initiators_lunmask


----- ----------------------

0 FC 20:00:00:e0:8b:88:b6:02,21:00:00:e0:8b:88:b6:02

1 FC 20:01:00:e0:8b:a8:b6:02,21:01:00:e0:8b:a8:b6:02

2 ISCSI iqn.1991-05.com.microsoft:qlogic-1

3 ISCSI iqn.1991-05.com.microsoft:qlogic-2


Target(WWPN) (LUN/VpGroup) VendorId

------------ ------------- --------

21:00:00:11:c6:17:12:22 0/VPGROUP_1 SEAGATE

50:06:01:60:3a:60:0a:63 0/VPGROUP_2

50:06:01:60:3a:60:0a:63 1/VPGROUP_2

50:06:01:60:3a:60:0a:63 2/VPGROUP_2

50:06:01:60:3a:60:0a:63 3/VPGROUP_2

50:06:01:60:3a:60:0a:63 4/VPGROUP_2

50:06:01:60:3a:60:0a:63 5/VPGROUP_2

50:06:01:60:3a:60:0a:63 6/VPGROUP_2

50:06:01:60:3a:60:0a:63 7/VPGROUP_2

50:06:01:60:3a:60:0a:63 8/VPGROUP_2


Commands

ISR654601-00 E 2-89

Show I/O StatisticsDisplays statistics of read/write operations for a selected device.

Authority None

Syntax show iostats

Examples The following example shows the show iostats command:

iSR6200 <1 #> show iostats


----- ----------------------

0 50:05:07:68:02:00:0f:02,50:05:07:68:02:10:0f:02

1 50:05:07:68:02:00:0f:03,50:05:07:68:02:10:0f:03


0 0/VPGROUP_1

60:05:07:68:02:81:80:5e:90:00:00:00:00:00:00:00

1 1/VPGROUP_1

60:05:07:68:02:81:80:5e:90:00:00:00:00:00:00:02


Lun Number 0

Read Byte Count 0

Write Byte Count 0

Read Count 0

Write Count 0


Commands

2-90 ISR654601-00 E

Show iSCSIDisplays iSCSI information for the specified port. If you do not specify the port, this command displays all ports.

Authority None

Syntax show iscsi [port_num]

Keywords [port_num]

The number of the iSCSI port to be displayed.

Examples The following example shows the show iscsi port command:

iSR6200 <1> (admin) #> show iscsi

iSCSI Port Information

------------------------

iSCSI Port GE1

Port Status Enabled

Port Mode iSCSI

Link Status Up

iSCSI Name iqn.2004-08.com.qlogic:isr6200.0951f00579.b1

Firmware Revision 3.00.01.57

Current Port Speed 1Gb/FDX

Programmed Port Speed Auto

MTU Size Normal

Window Size 65536

MAC Address 00-c0-dd-18-c9-88

IPv4 Address 10.3.5.6

IPv4 Subnet Mask 255.255.255.0

IPv4 Gateway Address 0.0.0.0

IPv4 Target TCP Port No. 3260

IPv4 VLAN Disabled

IPv6 Address 1 ::

IPv6 Address 2 ::

IPv6 Link Local fe80::2c0:ddff:fe18:c988

IPv6 Default Router ::


IPv6 VLAN Disabled

iSCSI Max First Burst 65536

iSCSI Max Burst 262144

iSCSI Header Digests Disabled


Commands

ISR654601-00 E 2-91

iSCSI Data Digests Disabled

Bandwidth, MB/sec 125

iSCSI Port GE2

Port Status Enabled

Port Mode iSCSI

Link Status Up



Current Port Speed 100Mb/FDX


MTU Size Normal

Window Size 65536

MAC Address 00-c0-dd-18-c9-89





IPv4 VLAN Disabled

IPv6 Address 1 ::

IPv6 Address 2 ::

IPv6 Link Local fe80::2c0:ddff:fe18:c989



IPv6 VLAN Disabled






iSCSI Port 10GE1/FCOE1

Port Status Enabled

Port Mode iSCSI

Link Status Down





MTU Size Normal


Commands

2-92 ISR654601-00 E

Window Size 65536

MAC Address 00-c0-dd-18-c9-8a





IPv4 VLAN Disabled

IPv6 Address 1 ::

IPv6 Address 2 ::

IPv6 Link Local fe80::2c0:ddff:fe18:c98a



IPv6 VLAN Disabled






iSCSI Port 10GE2/FCOE2

Port Status Enabled

Port Mode iSCSI

Link Status Down





MTU Size Normal

Window Size 65536

MAC Address 00-c0-dd-18-c9-8b





IPv4 VLAN Disabled

IPv6 Address 1 ::

IPv6 Address 2 ::

IPv6 Link Local fe80::2c0:ddff:fe18:c98b




Commands

ISR654601-00 E 2-93

IPv6 VLAN Disabled







Commands

2-94 ISR654601-00 E

Show iSNSDisplays iSNS configuration information for the specified iSCSI port. If you do not specify the port, this command displays the iSNS configuration information for all iSCSI ports.

Authority None

Syntax show isns [port_num]

Keywords [port_num]

The iSCSI port number whose iSNS configuration is to be displayed.

Examples The following example shows the show isns command:

iSR6200 <2> (admin) #> show isns

iSNS Information

----------------

iSNS Disabled

IP Address 0.0.0.0

TCP Port No. 3205


Commands

ISR654601-00 E 2-95

Show LogsDisplays either all or a portion of the router event log.

Authority None

Syntax show logs [last_x_entries]

Keywords [last_x_entries]

Shows only the last x number of logs entries. For example, show logs 10 displays the last ten entries in the router event log.

The show logs command displays the entire router event log.

Examples The following example shows the show logs command:

iSR6200 <1> #> show logs

01/01/2011 00:00:13 System 3 Tuesday 01 January 12:13 AM

01/01/2011 00:00:21 QL4022 3 #0: QLIsrDecodeMailbox: Link up

01/01/2011 00:00:13 System 3 Tuesday 01 January 12:13 AM

01/01/2011 00:00:22 QL4022 3 #0: QLIsrDecodeMailbox: Link up


Commands

2-96 ISR654601-00 E

Show LUN InfoDisplays complete information for a specified LUN and target.

Authority None

Syntax show luninfo

Examples The following example shows the show luninfo command:

iSR6200 <1> (admin) #> show luninfo


----- ----------------------

0 20:00:00:14:c3:3d:d2:e2,21:00:00:14:c3:3d:d2:e2

1 20:00:00:0c:50:a6:67:39,21:00:00:0c:50:a6:67:39

2 20:00:00:0c:50:a6:69:7e,21:00:00:0c:50:a6:69:7e

3 20:00:00:14:c3:3d:d3:55,21:00:00:14:c3:3d:d3:55

4 20:00:00:14:c3:3d:d3:57,21:00:00:14:c3:3d:d3:57

5 20:00:00:14:c3:3d:d3:8a,21:00:00:14:c3:3d:d3:8a

6 20:00:00:14:c3:3d:d3:51,21:00:00:14:c3:3d:d3:51

7 20:00:00:14:c3:44:9a:fe,21:00:00:14:c3:44:9a:fe

8 20:00:00:14:c3:3d:d4:07,21:00:00:14:c3:3d:d4:07

9 20:00:00:14:c3:3d:d2:c1,21:00:00:14:c3:3d:d2:c1

10 20:00:00:0c:50:a6:6a:92,21:00:00:0c:50:a6:6a:92

11 20:00:00:0c:50:a6:60:f1,21:00:00:0c:50:a6:60:f1

12 20:00:00:0c:50:a6:67:3b,21:00:00:0c:50:a6:67:3b

13 20:00:00:0c:50:a6:6a:60,21:00:00:0c:50:a6:6a:60

14 20:00:00:0c:50:a6:66:a2,21:00:00:0c:50:a6:66:a2

15 iqn.2001-05.com.equallogic:0-8a0906-bc4a49907-3b4fb16b0b14c529-demo

16 iqn.2001-05.com.equallogic:0-8a0906-fc9829a07-d41fb16bae64cffa-demo-1

17 iqn.2001-05.com.equallogic:0-8a0906-01e829a07-58afb16bae94cffb-demo-2


Index (LUN/VpGroup)

----- -------------

0 0/VPGROUP_1


LUN Information

-----------------

WWULN 20:00:00:14:c3:3d:d2:e2

LUN Number 0


Commands

ISR654601-00 E 2-97

VendorId SEAGATE

ProductId ST336754FC

ProdRevLevel XR22

Portal 0

Lun Size 35003 MB

Lun State Online

LUN Path Information

--------------------

Controller Id WWPN,PortId / IQN,IP Path Status

------------- --------------------------------- -----------

- 21:00:00:14:c3:3d:d2:e2, 62-01-63 Current


Commands

2-98 ISR654601-00 E

Show LUNsDisplays LUN information for each target.

Authority None

Syntax show luns

Examples The following example shows the show luns command:

iSR6200 <1> #> show luns

Target(WWPN) VpGroup LUN Serial Number/WWULN

------------ ------- --- -------------------

21:00:00:14:c3:3d:d2:e2 VPGROUP_1 0

21:00:00:0c:50:a6:67:39 VPGROUP_2 0

21:00:00:0c:50:a6:69:7e VPGROUP_2 0

21:00:00:14:c3:3d:d3:55 VPGROUP_1 0

21:00:00:14:c3:3d:d3:57 VPGROUP_1 0

21:00:00:14:c3:3d:d3:8a VPGROUP_1 0

21:00:00:14:c3:3d:d3:51 VPGROUP_1 0

21:00:00:14:c3:44:9a:fe VPGROUP_1 0

21:00:00:14:c3:3d:d4:07 VPGROUP_1 0

21:00:00:14:c3:3d:d2:c1 VPGROUP_1 0

21:00:00:0c:50:a6:6a:92 VPGROUP_2 0

21:00:00:0c:50:a6:60:f1 VPGROUP_2 0

21:00:00:0c:50:a6:67:3b VPGROUP_2 0

21:00:00:0c:50:a6:6a:60 VPGROUP_2 0

21:00:00:0c:50:a6:66:a2 VPGROUP_2 0

iSCSI Name

----------------------------------------------

iqn.2001-05.com.equallogic:0-8a0906-bc4a49907-3b4fb16b0b14c529-demo

LUN

---

0

iSCSI Name

----------------------------------------------

iqn.2001-05.com.equallogic:0-8a0906-fc9829a07-d41fb16bae64cffa-demo-1

LUN

---


Commands

ISR654601-00 E 2-99

0

iSCSI Name

----------------------------------------------

iqn.2001-05.com.equallogic:0-8a0906-01e829a07-58afb16bae94cffb-demo-2

LUN

---

0


Commands

2-100 ISR654601-00 E

Show LUN MaskDisplays all initiators mapped to a user-specified LUN.

Authority None

Syntax show lunmask

Examples The following example shows the show lunmask command:

iSR6200 <1> #> show lunmask


----- ----------------------

0 20:00:00:14:c3:3d:d2:e2,21:00:00:14:c3:3d:d2:e2

1 20:00:00:0c:50:a6:67:39,21:00:00:0c:50:a6:67:39

2 20:00:00:0c:50:a6:69:7e,21:00:00:0c:50:a6:69:7e

3 20:00:00:14:c3:3d:d3:55,21:00:00:14:c3:3d:d3:55

4 20:00:00:14:c3:3d:d3:57,21:00:00:14:c3:3d:d3:57

5 20:00:00:14:c3:3d:d3:8a,21:00:00:14:c3:3d:d3:8a

6 20:00:00:14:c3:3d:d3:51,21:00:00:14:c3:3d:d3:51

7 20:00:00:14:c3:44:9a:fe,21:00:00:14:c3:44:9a:fe

8 20:00:00:14:c3:3d:d4:07,21:00:00:14:c3:3d:d4:07

9 20:00:00:14:c3:3d:d2:c1,21:00:00:14:c3:3d:d2:c1

10 20:00:00:0c:50:a6:6a:92,21:00:00:0c:50:a6:6a:92

11 20:00:00:0c:50:a6:60:f1,21:00:00:0c:50:a6:60:f1

12 20:00:00:0c:50:a6:67:3b,21:00:00:0c:50:a6:67:3b

13 20:00:00:0c:50:a6:6a:60,21:00:00:0c:50:a6:6a:60

14 20:00:00:0c:50:a6:66:a2,21:00:00:0c:50:a6:66:a2

15 iqn.2001-05.com.equallogic:0-8a0906-bc4a49907-3b4fb16b0b14c529-demo

16 iqn.2001-05.com.equallogic:0-8a0906-fc9829a07-d41fb16bae64cffa-demo-1

17 iqn.2001-05.com.equallogic:0-8a0906-01e829a07-58afb16bae94cffb-demo-2


Index (LUN/VpGroup)

----- -------------

0 0/VPGROUP_1



Commands

ISR654601-00 E 2-101

Target iqn.2001-05.com.equallogic:0-8a0906-bc4a49907-3b4fb16b0b14c529-demo

LUN Initiator

--- -----------------

0 21:00:00:e0:8b:88:b6:02


Commands

2-102 ISR654601-00 E

Show MemoryDisplays free and total physical system memory and GE port connections. Does not display information about free space in /var/ftp/.

Authority None

Syntax show memory

Examples The following example shows the show memory command:

iSR6200 <1> (admin) #> show memory

Memory Units Free/Total

-------------- ----------

Physical 163MB/1002MB

Buffer Pool 7296/8320

Nic Buffer Pool 53344/65536

Process Blocks 8192/8192

Request Blocks 8192/8192

Event Blocks 4096/4096

Control Blocks 1018/1024

Client Req Blocks 8192/8192

FCIP Buffer Pool 0/0

FCIP Request Blocks 0/0

FCIP NIC Buffer Pool 0/0

1K Buffer Pool 69632/69632

4K Buffer Pool 4096/4096

Sessions 4096/4096

Connections:

GE1 256/256

GE2 256/256

10GE1 2048/2048

10GE2 2048/2048


Commands

ISR654601-00 E 2-103

Show MGMTDisplays the blade’s management port (10/100) configuration.

Authority None

Syntax show mgmt

Examples The following example shows the show mgmt command:

iSR6200 <1> (admin) #> show mgmt

Management Port Information

-----------------------------

IPv4 Interface Enabled

IPv4 Mode Dhcp

IPv4 IP Address 172.17.137.129


IPv4 Gateway 172.17.136.1

IPv6 Interface Disabled

Link Status Up

MAC Address 00-c0-dd-0c-8b-e1


Commands

2-104 ISR654601-00 E

Show NTPDisplays the router’s network time protocol (NTP) configuration.

Authority None

Syntax show ntp

Examples The following example shows the show ntp command:

iSR6200 <1> #> show ntp

NTP Information

-----------------

Mode Disabled

Status Offline

TimeZone Offset (Hours) 0


Commands

ISR654601-00 E 2-105

Show PerformanceDisplays the port, read, write, initiator, or target performance in bytes per second.

Authority None

Syntax show perf [ byte | init_rbyte | init_wbyte | tgt_rbyte | tgt_wbyte ]

Keywords byte

Displays performance data (bytes per second) for all ports. The show perf byte command also provides FCIP route performance numbers. If an FCIP route is configured, an additional column titled FCIPxCx shows the current per-second transmit compression ratio for the specified route.

init_rbyte

Displays initiator mode read performance.

init_wbyte

Displays initiator mode write performance.

tgt_rbyte

Displays target mode read performance.

tgt_wbyte

Displays target mode write performance.

Examples The following examples show the show perf command:

iSR6200 <1> #> show perf

WARNING: Valid data is only displayed for port(s) that are not

associated with any configured FCIP routes.

Port Bytes/s Bytes/s Bytes/s Bytes/s Bytes/s

Number (init_r) (init_w) (tgt_r) (tgt_w) (total)

------ -------- -------- -------- -------- --------

GE1 8M 9M 0 0 17M

GE2 0 0 0 0 0

GE3 0 0 0 0 0

GE4 0 0 0 0 0

FC1 7M 7M 0 0 15M

FC2 0 0 0 0 0

iSR6200 <1> #> show perf byte


Commands

2-106 ISR654601-00 E

WARNING: Valid data is only displayed for port(s) that are not

associated with any configured FCIP routes.

Displaying bytes/sec (total)... (Press any key to stop display)

GE1 GE2 GE3 GE4 FC1 FC2 FCIP1Cx

--------------------------------------------------------

11M 0 0 0 10M 0 0

12M 0 0 0 10M 0 0

12M 0 0 0 11M 0 0

12M 0 0 0 10M 0 0

12M 0 0 0 11M 0 0

12M 0 0 0 11M 0 0

12M 0 0 0 11M 0 0

11M 0 0 0 10M 0 0

11M 0 0 0 10M 0 0

13M 0 0 0 11M 0 0

12M 0 0 0 11M 0 0

12M 0 0 0 11M 0 0

12M 0 0 0 11M 0 0

11M 0 0 0 10M 0 0

13M 0 0 0 12M 0 0

13M 0 0 0 11M 0 0

14M 0 0 0 13M 0 0

14M 0 0 0 14M 0 0

16M 0 0 0 15M 0 0

17M 0 0 0 16M 0 0

17M 0 0 0 15M 0 0

17M 0 0 0 16M 0 0

iSR6200 <1> #> show perf init_rbyte

WARNING: Valid data is only displayed for port(s) that are not associated with any configured FCIP routes.

Displaying bytes/sec (initiator mode read)... (Press any key to stop display)

GE1 GE2 GE3 GE4 FC1 FC2

------------------------------------------------

0 0 0 0 0 0

0 0 0 0 0 0


Commands

ISR654601-00 E 2-107

iSR6200 <1> #> show perf tgt_wbyte

WARNING: Valid data is only displayed for port(s) that are notassociated with any configured FCIP routes.

Displaying bytes/sec (target mode write)... (Press any key ato stop display)

GE1 GE2 GE3 GE4 FC1 FC2

------------------------------------------------

0 0 0 0 0 0


Commands

2-108 ISR654601-00 E

Show Port StatisticsDisplays Fibre Channel or GbE port statistics.

Authority None

Syntax show portstats <fc | gige> <port-No> <hours | mins> <duration>

Keywords fc

Specifies the display of Fibre Channel port statistics.

gige

Specifies the display of GbE port statistics.

mins

Specifies that display of statistics by the minute.

hours

Specifies the display of statistics by the hour.

Examples The following examples show the show portstats fc command:

iSR6200 <1> #> show portstats fc 1 mins 10

This will display monitoring statistics of FC Port 1 for last 10 minute(s).

Statistics are displayed in reverse order.

If the router has been rebooted recently, the statistics are displayed

starting from the last reboot.

The statistics contain:

Current Date (once) at start, Time Stamp (TimeStamp),

TX bytes (TxByte), RX bytes (RxByte),

TX frames (TxFrame), RX frames (RxFrame),

FC Invalid CRC Count (CRCErr),

FC Link Failure Error Count (LinkErr),

FC Loss of Sync Error Count (LossSync),

FC Loss of Signal Error Count (LossSgnl),

FC Primitive Sequence Protocol Error Count (PSPErr)

FC Invalid Transmission Word Count (TXWrdErr)

Current Date 12/21/2011

TimeStamp TxByte RxByte TxFrame RxFrame CrcErr LinkErr LossSync LossSgnl PSPErr TXWrdErr

--------- ------ ------ ------- ------- ------ ------- -------- -------- ------ ------


Commands

ISR654601-00 E 2-109

11:45:48 336 288 6 6 0 0 0 0 0 0

11:44:48 336 288 6 6 0 0 0 0 0 0

11:43:48 336 288 6 6 0 0 0 0 0 0

11:42:48 336 288 6 6 0 0 0 0 0 0

11:41:48 336 288 6 6 0 0 0 0 0 0

11:40:48 336 288 6 6 0 0 0 0 0 0

11:39:48 336 288 6 6 0 0 0 0 0 0

11:38:48 604 524 10 10 0 0 0 0 0 0

11:37:48 336 288 6 6 0 0 0 0 0 0

11:36:48 336 288 6 6 0 0 0 0 0 0

iSR6200 <1> #> show portstats fc 1 hours 2

This will display monitoring statistics of FC Port 1 for last 2 hour(s).







TX frames (TxFrame), RX frames (RxFrame),

FC Invalid CRC Count (CRCErr),

FC Link Failure Error Count (LinkErr),

FC Loss of Sync Error Count (LossSync),

FC Loss of Signal Error Count (LossSgnl),

FC Primitive Sequence Protocol Error Count (PSPErr)

FC Invalid Transmission Word Count (TXWrdErr)


TimeStamp TxByte RxByte TxFrame RxFrame CrcErr LinkErr LossSync LossSgnl PSPErr TXWrdErr

--------- ------ ------ ------- ------- ------ ------- -------- -------- ------ ------

13:04:48 20K 17K 368 368 0 0 0 0 0 0

12:04:48 32K 29K 425 425 0 0 0 0 0 0


Commands

2-110 ISR654601-00 E

The following examples show the show portstats gige command:

iSR6200 <1> #> show portstats gige 1 mins 10

This will display monitoring statistics of GE Port 1 for last 10 minute(s).







TX packets (TxPkt), RX packets (RxPkt),

Maximum round trip time (MaxRTT), Minimum round trip time (MinRTT),

TCP retransmitted packets (ReTxPkt),

Number of TCP Connection drops (ConnDrop)


TimeStamp TxByte RxByte TxPkt RxPkt MaxRTT MinRTT ReTxPkt ConnDrop

--------- ------ ------ ----- ----- ------ ------ ------- --------

11:47:48 104K 104K 606 606 36 32 0 0

11:46:48 104K 104K 606 606 40 32 0 0

11:45:48 104K 104K 606 606 36 32 0 0

11:44:48 103K 103K 606 605 36 32 0 0

11:43:48 103K 103K 604 604 36 32 0 0

11:42:48 103K 103K 603 603 36 32 0 0

11:41:48 103K 103K 606 603 36 32 0 0

11:40:48 103K 103K 607 603 40 32 0 0

11:39:48 103K 103K 606 604 36 32 0 0

11:38:48 104K 104K 612 608 36 32 0 0

iSR6200 <1> #> show portstats gige 1 hours 2

This will display monitoring statistics of GE Port 1 for last 2 hour(s).







TX packets (TxPkt), RX packets (RxPkt),

Maximum round trip time (MaxRTT), Minimum round trip time (MinRTT),


Commands

ISR654601-00 E 2-111

TCP retransmitted packets (ReTxPkt),

Number of TCP Connection drops (ConnDrop)


TimeStamp TxByte RxByte TxPkt RxPkt MaxRTT MinRTT ReTxPkt ConnDrop

--------- ------ ------ ----- ----- ------ ------ ------- --------

13:04:48 5M 6M 28K 33K 40 0 0 0

12:04:48 5M 6M 30K 34K 40 0 0 0


Commands

2-112 ISR654601-00 E

Show Presented TargetsDisplays targets presented by the router: Fibre Channel, iSCSI, or both.

Authority None

Syntax show presented_targetsfc iscsi

Keywords fc

Specifies the display of Fibre Channel presented targets.

iscsi

Specifies the display of iSCSI presented targets.

Examples The following example shows the show presented_targets fc command:

iSR6200 <1> #> show presented_targets fc


------------------------------

FC/FCOE Presented Targets

----------------------

WWNN 20:04:00:c0:dd:13:17:e9

WWPN 21:04:00:c0:dd:13:17:e9

Port ID 62-06-04

Port FC2

Type FC

<MAPS TO>

Name iqn.2001-05.com.equallogic:0-8a0906-bc4a49907-3b4fb16b0b14c529-demo

WWNN 20:04:00:c0:dd:13:17:e8

WWPN 21:04:00:c0:dd:13:17:e8

Port ID 01-01-04

Port FC1

Type FC

<MAPS TO>

Name iqn.2001-05.com.equallogic:0-8a0906-bc4a49907-3b4fb16b0b14c529-demo

WWNN 20:05:00:c0:dd:13:17:e8

WWPN 21:05:00:c0:dd:13:17:e8

Port ID 01-01-05


Commands

ISR654601-00 E 2-113

Port FC1

Type FC

<MAPS TO>

Name iqn.2001-05.com.equallogic:0-8a0906-fc9829a07-d41fb16bae64cffa-demo-1

WWNN 20:06:00:c0:dd:13:17:e8

WWPN 21:06:00:c0:dd:13:17:e8

Port ID 01-01-06

Port FC1

Type FC

<MAPS TO>

Name iqn.2001-05.com.equallogic:0-8a0906-01e829a07-58afb16bae94cffb-demo-2

The following example shows the show presented_targets iscsi command:

iSR6200 <1> #> show presented_targets iscsi


------------------------------

iSCSI Presented Targets

-------------------------

Name iqn.2000-04.com.qlogic:iSR6200:0.50001fe150069d20.50001fe150069d2c

IP 10.3.5.66

CHAP Disabled

<MAPS TO>

WWNN 50:00:1f:e1:50:06:9d:20

WWPN 50:00:1f:e1:50:06:9d:2c

Name iqn.2000-04.com.qlogic:iSR6200:1.50001fe150069d20.50001fe150069d2c

IP 10.3.5.67

CHAP Disabled

<MAPS TO>

WWNN 50:00:1f:e1:50:06:9d:20

WWPN 50:00:1f:e1:50:06:9d:2c

Name iqn.2000-04.com.qlogic:iSR6200:0.50001fe150011150.50001fe150011158

IP 10.3.5.66

CHAP Disabled

<MAPS TO>

WWNN 50:00:1f:e1:50:01:11:50


Commands

2-114 ISR654601-00 E

WWPN 50:00:1f:e1:50:01:11:58

Name iqn.2000-04.com.qlogic:iSR6200:1.50001fe150011150.50001fe150011158

IP 10.3.5.67

CHAP Disabled

<MAPS TO>

WWNN 50:00:1f:e1:50:01:11:50

WWPN 50:00:1f:e1:50:01:11:58


Commands

ISR654601-00 E 2-115

Show PropertiesDisplays the router blade CLI properties.

Authority None

Syntax show properties

Examples The following example shows the show properties command:

iSR6200 <1> #> show properties

CLI Properties

----------------

Inactivty Timer 15 minutes

Prompt String iSR6200


Commands

2-116 ISR654601-00 E

Show Remote MapsDisplays all remote maps that have been configured.

Authority None

Syntax show remotemaps

Examples The following example shows the show remotemaps command:

iSR6200 <1> (admin) #> show remotemaps

Remote Mappings

-----------------

Local Device 50:06:01:60:c1:e0:49:2e,50:06:01:61:41:e0:49:2e

Remote Device 20:00:00:1b:32:1a:59:e6,21:00:00:1b:32:1a:59:e6

Local Port FC1

Remote Port FC1

Remote System iSR6200(172.35.15.131)

Status Online

Smart-Write Enabled

Compression Disabled

Load Balance Enabled


Commands

ISR654601-00 E 2-117

Show Remote PeersDisplays information for all remote peers.

Authority None

Syntax show remotepeers

Examples The following example shows the show remotepeers command:

iSR6200 <1> (admin) #> show remotepeers

Remote Peer System Information

------------------------------







Mgmt IPv6 Link-Local ::



No. of iSCSI Remote Connections 2




Commands

2-118 ISR654601-00 E

Show RPC InfoDisplays remote procedure call (RPC) information, including port and program numbers.

Authority None

Syntax show rpcinfo

Examples The following example shows the show rpcinfo command:

iSR6200 <1> #> show rpcinfo

Rpc Information

------------------

program vers proto port service

100000 4 tcp 111 portmapper



100000 4 udp 111 portmapper



100000 4 0 111 portmapper



351517 1 udp 718

351517 1 tcp 718

351516 1 udp 718

351516 1 tcp 718

351522 1 udp 720

351522 1 tcp 720

351521 1 udp 893

351521 1 tcp 893

351515 1 udp 944

351515 1 tcp 944


Commands

ISR654601-00 E 2-119

Show SmartWrite DevicesDisplays the port names of Fibre Channel devices (initiators and targets) that can be remotely mapped using SmartWrite.

QLogic developed SmartWrite as a solution to optimize data transfer by linking SANs over WANs. SmartWrite improves performance, lowers management overhead, consolidates islands of multi-vendor SANs, and improves utilization of WAN and SAN resources.

Authority None

Syntax show swdevices

Examples The following example shows the show swdevices command:

iSR6200 <1> (admin) #> show swdevices

Smart Write Discovered Device Information

-----------------------------------------

WWNN 50:06:01:60:c1:e0:49:2e

WWPN 50:06:01:69:41:e0:49:2e

Port ID 6e-00-00

State Online

WWNN 50:06:01:60:c1:e0:49:2e

WWPN 50:06:01:61:41:e0:49:2e

Port ID 6e-07-00

State Online


Commands

2-120 ISR654601-00 E

Show SNMPDisplays the router’s simple network management protocol (SNMP) and any configured traps.

Authority None

Syntax show snmp

Examples The following example shows the show snmp command:

iSR6200 <1> (admin) #> show snmp

SNMP Configuration

------------------

Read Community Public

Trap Community Private

System Location

System Contact

Authentication traps Disabled

System OID 1.3.6.1.4.1.3873.1.17

System Description iSR6200

Trap Destination 1

------------------

IP Address 10.0.0.5

Trap Port 1024

Trap Version 2


Commands

ISR654601-00 E 2-121

Show StatsDisplays the blade statistics for Fibre Channel and iSCSI.

Authority None

Syntax show stats

Examples The following example shows the show stats command:

iSR6200 <1> #> show stats

FC Port Statistics

--------------------

FC Port 1

Interrupt Count 23

Target Command Count 0

Initiator Command Count 0

FC Port 2

Interrupt Count 1717443350



iSCSI Port Statistics

-----------------------

iSCSI Port 1




MAC Xmit Frames 54392137663

MAC Xmit Byte Count 61199467593726

MAC Xmit Multicast Frames 0

MAC Xmit Broadcast Frames 0

MAC Xmit Pause Frames 0

MAC Xmit Control Frames 0

MAC Xmit Deferrals 0

MAC Xmit Late Collisions 0

MAC Xmit Aborted 0

MAC Xmit Single Collisions 0

MAC Xmit Multiple Collisions 0

MAC Xmit Collisions 0

MAC Xmit Dropped Frames 0


Commands

2-122 ISR654601-00 E

MAC Xmit Jumbo Frames 0

MAC Rcvd Frames 42061498217

MAC Rcvd Byte Count 60362392962831

MAC Rcvd Unknown Control Frames 0

MAC Rcvd Pause Frames 0

MAC Rcvd Control Frames 0

MAC Rcvd Dribbles 0

MAC Rcvd Frame Length Errors 0

MAC Rcvd Jabbers 0

MAC Rcvd Carrier Sense Errors 0

MAC Rcvd Dropped Frames 0

MAC Rcvd CRC Errors 0

MAC Rcvd Encoding Errors 0

MAC Rcvd Length Errors Large 1

MAC Rcvd Small Errors Small 0

MAC Rcvd Multicast Frames 34394

MAC Rcvd Broadcast Frames 33144

iSCSI Port 2




MAC Xmit Frames 0

MAC Xmit Byte Count 0

MAC Xmit Multicast Frames 0

MAC Xmit Broadcast Frames 0

MAC Xmit Pause Frames 0




MAC Xmit Aborted 0






MAC Rcvd Frames 186

MAC Rcvd Byte Count 39260

MAC Rcvd Unknown Control Frames 0

MAC Rcvd Pause Frames 0


Commands

ISR654601-00 E 2-123


MAC Rcvd Dribbles 0


MAC Rcvd Jabbers 0




MAC Rcvd Encoding Errors 0

MAC Rcvd Length Errors Large 0

MAC Rcvd Small Errors Small 0

MAC Rcvd Multicast Frames 94

MAC Rcvd Broadcast Frames 91

iSCSI Shared Statistics

-----------------------

PDUs Xmited 2729500577

Data Bytes Xmited 55036896842234

PDUs Rcvd 2655246170

Data Bytes Rcvd 0

I/O Completed 1815115669

Unexpected I/O Rcvd 0

iSCSI Format Errors 0

Header Digest Errors 0

Data Digest Errors 0

Sequence Errors 0

PDU Xmit Count 2729500577



IP Xmit Packets 54392134283

IP Xmit Byte Count 59132566295008

IP Xmit Fragments 0

IP Rcvd Packets 42061430681

IP Rcvd Byte Count 58764046068744

IP Rcvd Fragments 0

IP Datagram Reassembly Count 0

IP Error Packets 0

IP Fragment Rcvd Overlap 0

IP Fragment Rcvd Out of Order 0

IP Datagram Reassembly Timeouts 0

TCP Xmit Segment Count 54392134284


Commands

2-124 ISR654601-00 E

TCP Xmit Byte Count 57389353022514

TCP Rcvd Segment Count 42061430681

TCP Rcvd Byte Count 57418079800284

TCP Persist Timer Expirations 0

TCP Rxmit Timer Expired 116

TCP Rcvd Duplicate Acks 986657165

TCP Rcvd Pure Acks 816265831

TCP Xmit Delayed Acks 3584507

TCP Rcvd Pure Acks 177811024

TCP Rcvd Segment Errors 0

TCP Rcvd Segment Out of Order 1

TCP Rcvd Window Probes 0

TCP Rcvd Window Updates 18500272

TCP ECC Error Corections 0

FCIP Link Statistics

--------------------

FCIP Link 1

FC Xmit Frames 0

FC Xmit Bytes 0

FC Rcvd Frames 0

FC Rcvd Bytes 0



IP Xmit Fragments 608



IP Rcvd Fragments 608


IP V6Pkt Rcvd 0

IP Error Packets 3701

IP Reassembly Errors 0



TCP Xmit Acks 0



TCP Rcvd Acks 0


TCP Timer Expired 0


Commands

ISR654601-00 E 2-125



MAC Xmit Bytes 337380

MAC Xmit Multicast Count 0

MAC Xmit Broadcast Count 0

MAC Xmit Pause Count 0




MAC Xmit Aborted 0







MAC Rcvd Bytes 215578

MAC Rcvd Multicast Count 0

MAC Rcvd Broadcast Count 0

MAC Rcvd Pause Count 0


MAC Rcvd Dribbles 0


MAC Rcvd Jabbers 0




MAC Rcvd Encoding Error 0

MAC Rcvd Length Errors 0

Compression Ratio Average 1


Commands

2-126 ISR654601-00 E

Show Stats FCIPDisplays the blade statistics specific to FCIP routes.

Authority None

Syntax show statsfcip

Examples The following example shows the show statsfcip command:

iSR6200 <2> #> show statsfcip

FCIP Link Statistics

-----------------------

FCIP Link 2

FC Xmit Frames 0

FC Xmit Bytes 0

FC Rcvd Frames 0

FC Rcvd Bytes 0



IP Xmit Fragments 633



IP Rcvd Fragments 633


IP V6Pkt Rcvd 0

IP Error Packets 0

IP Reassembly Errors 0



TCP Xmit Acks 0



TCP Rcvd Acks 0


TCP Timer Expired 0


TCP Reordering 0


MAC Xmit Bytes 1252975

MAC Xmit Multicast Count 19530

MAC Xmit Broadcast Count 0


Commands

ISR654601-00 E 2-127

MAC Xmit Pause Count 0




MAC Xmit Aborted 0







MAC Rcvd Bytes 1249647

MAC Rcvd Multicast Count 19478

MAC Rcvd Broadcast Count 0

MAC Rcvd Pause Count 0


MAC Rcvd Dribbles 0


MAC Rcvd Jabbers 0




MAC Rcvd Encoding Error 0

MAC Rcvd Length Errors 0

MAC Rcvd FIFO Errors 0


Commands

2-128 ISR654601-00 E

Show SystemDisplays blade product information, including the serial number, hardware and software versions, port quantities, and temperature.

Authority None

Syntax show system

Examples The following example shows the show system command:

iSR6200 <1> (admin) #> show system

System Information

--------------------



Target Presentation Mode Auto

Lun Mapping Enabled

Controller Lun AutoMap Disabled

Target Access Control Enabled

Time To Target Device Offline 0



SW Version 3.3.0.0

Boot Loader Version 0.97.0.4

BIOS Version 6.0.0.5

No. of FC Ports 4


Log Level 0

Telnet Enabled

SSH Enabled

FTP Enabled


Uptime 0Days0Hrs4Mins59Secs


Commands

ISR654601-00 E 2-129

Show TargetsDisplays targets discovered by the router: Fibre Channel, iSCSI, or both.

Authority None

Syntax show targetsfc scsi

Keywords fc

Specifies the display of Fibre Channel targets.

iscsi

Specifies the display of iSCSI targets.

Examples The following example shows the show targets fc command:

iSR6200 <1> #> show targets fc

Target Information

--------------------

WWNN 20:00:00:14:c3:3d:d2:bf

WWPN 22:00:00:14:c3:3d:d2:bf

Port ID 01-02-31

State Online

WWNN 20:00:00:14:c3:44:9b:86

WWPN 22:00:00:14:c3:44:9b:86

Port ID 01-02-32

State Online

WWNN 20:00:00:14:c3:44:9b:9d

WWPN 22:00:00:14:c3:44:9b:9d

Port ID 01-02-33

State Online

WWNN 20:00:00:14:c3:44:9a:fa

WWPN 22:00:00:14:c3:44:9a:fa

Port ID 01-02-34

State Online


Commands

2-130 ISR654601-00 E

The following example shows the show targets iscsi command:

iSR6200 <1> #> show targets iscsi

Target Information

--------------------

iSCSI Name iqn.2001-05.com.equallogic:0-8a0906-bc4a49907-3b4fb16b0b14c529-demo

Alias

State Online

IP Address 10.3.5.2 (Logged In --> GE1)

iSCSI Name iqn.2001-05.com.equallogic:0-8a0906-fc9829a07-d41fb16bae64cffa-demo-1

Alias

State Online


iSCSI Name iqn.2001-05.com.equallogic:0-8a0906-01e829a07-58afb16bae94cffb-demo-2

Alias

State Online



Commands

ISR654601-00 E 2-131

Show VPGroupsDisplays information about the blade’s configured virtual port groups.

Authority None

Syntax show vpgroups [vp index]

Keywords vp index

The number (1–4) of the virtual port group to be displayed.

Examples The following example shows the show vpgroups command for a specific virtual port group:

iSR6200 <1> #> show vpgroups 2

VpGroup Information

---------------------

Index 2

VpGroup Name VPGROUP_2

Status Enabled

WWPNs 21:01:00:c0:dd:13:16:f8

21:01:00:c0:dd:13:16:f9

The following example shows the show vpgroups command for all virtual port groups:

iSR6200 <1> #> show vpgroups

VpGroup Information

---------------------

Index 1


Status Enabled

WWPNs 21:00:00:c0:dd:13:16:f8

21:00:00:c0:dd:13:16:f9

Index 2


Status Enabled

WWPNs 21:01:00:c0:dd:13:16:f8

21:01:00:c0:dd:13:16:f9

Index 3



Commands

2-132 ISR654601-00 E

Status Enabled

WWPNs 21:02:00:c0:dd:13:16:f8

21:02:00:c0:dd:13:16:f9

Index 4


Status Enabled

WWPNs 21:03:00:c0:dd:13:16:f8

21:03:00:c0:dd:13:16:f9


Commands

ISR654601-00 E 2-133

ShutdownShuts down the blade.


Syntax shutdown

Examples The following example shows the shutdown command:

iSR6200 <1> (admin) #> shutdown

Are you sure you want to shutdown the System (y/n): n

Command aborted.


Commands

2-134 ISR654601-00 E

SmartWrite DeviceRemoves the specified offline Fibre Channel device from the list of available SmartWrite devices.


Syntax swdevicerm

Keywords rm

Removes the selected offline Fibre Channel device.

Examples The following example shows the swdevice rm command:

iSR6200 <1> (admin) #> swdevice rm

Index State (WWNN,WWPN/iSCSI Name)

----- ----- ----------------------

0 Offline 50:06:01:60:cb:a0:35:f6,50:06:01:61:4b:a0:35:f6

Please select an 'OFFLINE' Device from the list above ('q' to quit): 0



Commands

ISR654601-00 E 2-135

TargetRemoves an offline target from the blade’s database. Typically, you will use this command to remove targets from the database that are no longer connected to the router.


Syntax targetadd rm

Keywords add

Not supported.

rm

Removes a target from the router’s target database.

Examples The following example shows the target add command:

iSR6200 <1> (admin) #> target add

Command 'target add' is currently not supported.

The following example shows the target rm (remove) command:

iSR6200 <1> (admin) #> target rm

Index State (WWNN,WWPN/iSCSI Name)

----- ----- ----------------------

0 Offline 20:00:00:14:c3:3d:d2:bf,22:00:00:14:c3:3d:d2:bf

1 Online 20:00:00:14:c3:44:9b:86,22:00:00:14:c3:44:9b:86

2 Online 20:00:00:14:c3:44:9b:9d,22:00:00:14:c3:44:9b:9d

3 Online 20:00:00:14:c3:44:9a:fa,22:00:00:14:c3:44:9a:fa

Please select an OFFLINE Target from the list above ('q' to quit): 0


NOTE:

The target add command is not currently supported.


Commands

2-136 ISR654601-00 E

Target MapPresents or removes existing presentation of discovered Fibre Channel and iSCSI targets on Fibre Channel and iSCSI ports.


Syntax targetmapaddrm

Keywords add

Adds the target presentation.

rm

Removes the target presentation by removing a target from the router’s target database.

Examples The following example shows the targetmap add command using the manual option:

iSR6200 <1> (admin) #> targetmap add


----- ----------------------

0 50:00:1f:e1:50:0a:e1:40,50:00:1f:e1:50:0a:e1:49

1 50:00:1f:e1:50:0a:e1:40,50:00:1f:e1:50:0a:e1:4d

2 50:06:01:60:c1:e0:49:2e,50:06:01:62:41:e0:49:2e

3 50:06:01:60:c1:e0:49:2e,50:06:01:6a:41:e0:49:2e

4 50:00:1f:e1:50:0a:37:10,50:00:1f:e1:50:0a:37:18

5 50:00:1f:e1:50:0a:37:10,50:00:1f:e1:50:0a:37:1c

6 50:0a:09:80:88:8c:a7:79,50:0a:09:82:98:8c:a7:79

7 50:0a:09:80:88:8c:a7:79,50:0a:09:82:88:8c:a7:79

Please select a target from the list above ('q' to quit): 7

Index (IP/WWNN) (MAC/WWPN) (Portal)

----- ----------- ------------ --------

0 20.20.20.79 00-c0-dd-18-cf-91 1GE1

1 0.0.0.0 00-c0-dd-18-cf-92 1GE2

2 20:00:00:c0:dd:18:cf:91 21:00:00:c0:dd:18:cf:91 FC1

3 20:00:00:c0:dd:18:cf:92 21:00:00:c0:dd:18:cf:92 FC2

Please select a portal from the list above ('q' to quit): 2


Commands

ISR654601-00 E 2-137

Do you want to automap the selected target (Yes/No) [Yes ]No

Only Byte 1 of the selected FC portal is allowed to be modified.

Valid range for Byte 1 is 09-FF. Ex: 09, 0A, 0B....

Ex: 21:09:00:c0:dd:18:cf:91

FC presented target WWPN [ ] : 21:09:00:c0:dd:18:cf:91

Only Byte 1 of the selected FC portal is allowed to be modified.

Valid range for Byte 1 is 09-FF. Ex: 09, 0A, 0B....

Ex: 20:09:00:c0:dd:18:cf:91

FC presented target WWNN [ ] : 20:09:00:c0:dd:18:cf:91


The following example shows the targetmap add command using the automap option:

iSR6200 <1> (admin) #> targetmap add


----- ----------------------

0 50:00:1f:e1:50:0a:e1:40,50:00:1f:e1:50:0a:e1:49

1 50:00:1f:e1:50:0a:e1:40,50:00:1f:e1:50:0a:e1:4d

2 50:06:01:60:c1:e0:49:2e,50:06:01:62:41:e0:49:2e

3 50:06:01:60:c1:e0:49:2e,50:06:01:6a:41:e0:49:2e

4 50:00:1f:e1:50:0a:37:10,50:00:1f:e1:50:0a:37:18

5 50:00:1f:e1:50:0a:37:10,50:00:1f:e1:50:0a:37:1c

6 50:0a:09:80:88:8c:a7:79,50:0a:09:82:98:8c:a7:79

7 50:0a:09:80:88:8c:a7:79,50:0a:09:82:88:8c:a7:79


Index (IP/WWNN) (MAC/WWPN) (Portal)

----- ----------- ------------ --------

0 20.20.20.79 00-c0-dd-18-cf-91 1GE1

1 0.0.0.0 00-c0-dd-18-cf-92 1GE2

2 20:00:00:c0:dd:18:cf:91 21:00:00:c0:dd:18:cf:91 FC1

3 20:00:00:c0:dd:18:cf:92 21:00:00:c0:dd:18:cf:92 FC2

Please select a portal from the list above ('q' to quit): 3

Do you want to automap the selected target (Yes/No) [Yes ]



Commands

2-138 ISR654601-00 E

The following example shows the targetmap rm command:

iSR6200 <1> admin) #> targetmap rm

Warning: This command will cause the removal of all mappings and hosts

will loose access to disks.

Index State VpGroup Port (WWNN,WWPN/iSCSI Name)

----- ----- ------ ---- ----------------------

0 Online 1 FC1 20:00:00:0c:50:a6:67:39,21:00:00:0c:50:a6:67:39




Commands

ISR654601-00 E 2-139

TraceroutePrints the route a network packet takes to reach the destination specified by the user.


Syntax traceroute

Examples The following example shows the traceroute command:

iSR6200 <1> (admin) #> traceroute





IP Address (IPv4 or IPv6) [0.0.0.0] 172.35.14.17

Outbound Port (0=Mgmt, 1=GE1, 2=GE2, ...) [Mgmt ] 0

Tracing route to 172.35.14.17 over a maximum of 30 hops:

1 172.17.136.2 0.4ms 0.3ms 0.5ms

2 10.7.9.5 1.1ms 1.1ms 1.1ms

3 172.21.130.233 2.7ms 2.7ms 2.6ms

4 172.21.4.245 291.4ms 291.4ms 291.4ms

5 172.21.4.246 413.6ms 417.1ms 439.2ms

6 10.35.9.1 459.1ms 465.6ms 480.0ms

7 172.35.14.17 495.3ms 483.0ms 505.9ms

Traceroute completed in 7 hops.


Commands

2-140 ISR654601-00 E

ISR654601-00 E 3-1

3 Configuring CHAP

In challenge handshake authentication protocol (CHAP), the authentication agent sends the client program an ID value and a random value that is used only once. Both the sender and peer share a predefined secret. The peer concatenates the random value, the ID, and the secret. Then it calculates a one-way hash using message-digest algorithm 5 (MD5). The peer sends the hash value to the authenticator, which in turn builds that same string on its side, calculates the MD5 checksum, and compares the result with the value received from the peer. If the values match, the peer is authenticated.

By transmitting only the hash, the secret cannot be reverse-engineered. The algorithm increases the ID value with each CHAP dialog to protect against replay attacks.

This chapter provides the procedures for configuring CHAP from the command line interface (CLI), including:

“Discovery Session—Bi-directional CHAP” on page 3-2

“Discovery Session—Uni-directional CHAP” on page 3-3

“Normal Session—Bi-directional CHAP” on page 3-4

“Normal Session—Uni-directional CHAP” on page 3-5

3–Configuring CHAP

Discovery Session—Bi-directional CHAP

3-2 ISR654601-00 E

Discovery Session—Bi-directional CHAPFollow this procedure to configure a bi-directional (BiDi) CHAP used during a discovery session.

To configure a BiDi CHAP in a discovery session:

1. On the router, follow these steps:

a. Enable CHAP on the port.

b. Create a secret (for example, secret_port).

c. Using the set chap command, choose the iSCSI node that represents the GE port.

d. To find the iSCSI node name of the GE port, execute the show iscsi command.

2. To add the initiator that is about to do discovery, execute the initiator add command as follows:

a. Enable the CHAP for this initiator.

b. Create a secret (for example, secret_initiator).

c. To update the CHAP settings of the initiator, execute the set chap command.

3. Go to the Microsoft iSCSI (MS) Initiator and follow these steps:

a. Click General.

b. Click Secret (in the middle of the window). If this is the first time you are setting secrets, reset all secrets.

c. Type the secret (secret_port) that you created in Step 1.

4. Click Discovery.

5. Click Add.

6. Type the address of the iSCSI port of the router.

7. Click Advanced.

8. Select Chap Login Information.

9. Type the secret (secret_initiator) you created in Step 2 into Target Secret.

10. Select Mutual Authentication.

11. Click OK.

12. Click OK.

The initiator completes the discovery.


Discovery Session—Uni-directional CHAP

ISR654601-00 E 3-3

Discovery Session—Uni-directional CHAPFollow this procedure to configure a uni-directional CHAP used during a discovery session.

To configure a uni-directional CHAP in a discovery session:

1. Do not enable CHAP on the ISCSI port.

2. Execute the initiator add command as follows:

a. Add the initiator that is about to perform the discovery.

b. Enable the CHAP for this initiator.

c. Create a secret (for example, secret_initiator).

d. Use Set Chap to update the initiator’s CHAP settings.

3. Go to the MS Initiator.

4. Click Discovery.

5. Click Add.

6. Type the address of the iSCSI port of the router.

7. Click Advanced.


9. In Target Secret, type the secret (secret_initiator) you created in Step 2.

10. Click OK.

11. Click OK.

The initiator completes the discovery.


Normal Session—Bi-directional CHAP

3-4 ISR654601-00 E

Normal Session—Bi-directional CHAPFollow this procedure to configure a bi-directional (BiDi) CHAP used during a normal session.

To configure BiDi CHAP in a normal session:

1. On the router, follow these steps.

a. Enable CHAP on the presented target to which the initiator will login.

b. Create a secret (for example, secret_target).

c. Use Set CHAP.

2. To add the initiator that is about to do a normal login, execute the initiator add command as follows:

a. Enable the CHAP for this initiator.

b. Create a secret (for example, secret_initiator).

c. To update the CHAP settings of the initiator, execute the set chap command.

3. Go to the MS Initiator and follow these steps:

a. Click General.

b. Click Secret (in the middle of the window).

c. If this is the first time you are setting secrets, reset all the secrets.

d. Type the secret (secret_target) that you created in Step 1.

4. Click Targets.

5. Select the target you want to log in to.

6. Click Advanced.


8. In Target Secret, type the secret (secret_initiator) that you created in Step 2.

9. Select Mutual Authentication.

10. Click OK.

11. Click OK.

The initiator completes the normal login.


Normal Session—Uni-directional CHAP

ISR654601-00 E 3-5

Normal Session—Uni-directional CHAPFollow this procedure to configure a uni-directional CHAP used during a normal session.

To configure uni-directional CHAP in a normal session:

1. Do not enable CHAP on the presented target.

2. Execute the initiator add command as follows:

a. Add the initiator that is about to do a normal login.

b. Enable the CHAP for this initiator.

c. Create a secret (for example, secret_initiator).

d. To update the CHAP settings of the initiator, execute the set chap command.

3. Go to the MS Initiator.

4. Click Targets.

5. Select the target you want to log into.

6. Click Advanced.


8. In Target Secret, type the secret (secret_initiator) that you created in Step 2.

9. Click OK.

10. Click OK.

The initiator completes the normal login.


Normal Session—Uni-directional CHAP

3-6 ISR654601-00 E

ISR654601-00 E 4-1

4 Virtual Port Groups

Some virtualized storage arrays limit the number of LUNs exposed to a host to 256 LUNs. In order to access more than 256 LUNs per target, each iSR6200 blade supports up to four virtual port groups (VPGs). If you want your iSCSI hosts to have access to a total of more than 256 distinct LUNS from a specified Fibre Channel target array, you must enable and configure additional virtual port groups.

Each blade has VPG 1 enabled by default; VPG 1 is the primary virtual port group and cannot be disabled. Enabling extra virtual port groups will create additional logical Fibre Channel adapter initiator ports on the fabric. These ports act as separate Fibre Channel adapter host ports, and an additional 256 LUNs can be presented to each of them. With all four virtual port groups enabled, a single iSR6200 blade can access up to1,024 LUNs from a single Fibre Channel storage array.

This chapter provides the following virtual port group information:

“Displaying Virtual Port Groups” on page 4-2

“Enabling Virtual Port Groups” on page 4-3

4–Virtual Port Groups

Displaying Virtual Port Groups

4-2 ISR654601-00 E

Displaying Virtual Port GroupsTo display virtual port group information, use the show vpgroups command in the CLI. For example:

iSR6200 <1> (admin) #> show vpgroups

VpGroup Information

---------------------

Index 1


Status Enabled

WWPNs 21:00:00:c0:dd:13:16:f8

21:00:00:c0:dd:13:16:f9

Index 2


Status Disabled

WWPNs N/A

Index 3


Status Disabled

WWPNs N/A

Index 4


Status Disabled

WWPNs N/A


Enabling Virtual Port Groups

ISR654601-00 E 4-3

Enabling Virtual Port GroupsYou can enable or disable virtual port groups on your blade using the set vpgroups command.

The following example shows how to enable virtual port groups 2 and 3.

iSR6200 <1> (admin) #> set vpgroups






-------------------------

Status (0=Enable, 1=Disable) [Enabled ]




-------------------------





-------------------------





-------------------------

Status (0=Enable, 1=Disable) [Disabled ]




4-4 ISR654601-00 E

The following example shows the output from the CLI for an iSR6200 blade with three virtual port groups enabled. You can display information about the virtual port groups configured on your iSR6200 with the show vpgroups command:

iSR6200 <1> (admin) #> show vpgroups

VpGroup Information

---------------------

Index 1


Status Enabled

WWPNs 21:00:00:c0:dd:13:16:f8

21:00:00:c0:dd:13:16:f9

Index 2


Status Enabled

WWPNs 21:01:00:c0:dd:13:16:f8

21:01:00:c0:dd:13:16:f9

Index 3


Status Enabled

WWPNs 21:02:00:c0:dd:13:16:f8

21:02:00:c0:dd:13:16:f9

Index 4


Status Disabled

WWPNs N/A

Note that in the world wide port number (WWPN), the second byte from the left (for example, 21:01:00:c0:dd:13:16:f8) denotes the virtual port group ID, and the right most byte (for example, 21:01:00:c0:dd:13:16:f8) denotes the physical Fibre Channel port. In this example VPGs 1 through 3 have corresponding virtual ports with 00, 01, and 02 presented out of physical Fibre Channel ports 0 and 1, with WWPNs ending in f8 and f9, respectively.



ISR654601-00 E 4-5

The following example shows the same information grouped by physical Fibre Channel port:

iSR6200 <1> (admin) #> show fc

FC Port Information

---------------------

FC Port FC1

Port Status Enabled

Port Mode FCP

Link Status Up



WWNN 20:00:00:c0:dd:13:17:e8 (VPGROUP_1)

WWPN 21:00:00:c0:dd:13:17:e8 (VPGROUP_1)

Port ID 01-01-00 (VPGROUP_1)











Frame Size 2048


Connection Mode Point-to-Point

SFP Type 8Gb

FC Port FC2

Port Status Enabled

Port Mode FCP

Link Status Up









4-6 ISR654601-00 E










Frame Size 2048


Connection Mode Point-to-Point

SFP Type 8Gb

FC Port FCOE1

Port Status Enabled

Port Mode FCP

Link Status Down

Current Link Rate Unknown


WWNN 20:00:00:c0:dd:13:17:ea

WWPN 21:00:00:c0:dd:13:17:ea

Port ID 00-00-00


Frame Size 2048


Connection Mode Unknown

SFP Type 10Gb

Enode MAC Address 00-c0-dd-13-17-ee

Fabric Provided MAC Address 00-00-00-00-00-00

VlanId 0

Priority Level 0

Priority GroupId 0

Priority GroupPercentage 0

FC Port FCOE2

Port Status Enabled

Port Mode FCP

Link Status Down

Current Link Rate Unknown



ISR654601-00 E 4-7


WWNN 20:00:00:c0:dd:13:17:eb

WWPN 21:00:00:c0:dd:13:17:eb

Port ID 00-00-00


Frame Size 2048


Connection Mode Unknown

SFP Type 10Gb

Enode MAC Address 00-c0-dd-13-17-ef

Fabric Provided MAC Address 00-00-00-00-00-00

VlanId 0

Priority Level 0

Priority GroupId 0

Priority GroupPercentage 0

iSR6200 <1> (admin) #>

Again, notice in the preceding example that the VP index (see vp index keyword in “Show VPGroups” on page 2-131) is in the second byte from the left, and the Fibre Channel port indicator is in the right-most byte.



4-8 ISR654601-00 E

ISR654601-00 E 5-1

5 Configuring Fibre Channel Initiators to iSCSI Storage

This chapter provides instructions for connecting Fibre Channel hosts to iSCSI targets using the QLogic iSR6240 and iSR6250 routers. These routers are collectively referred to as the iSR6200 throughout this chapter.

PrerequisitesBefore connecting the Fibre Channel hosts to the iSCSI targets:

1. Configure the router iSCSI ports.

2. Allow access from the iSCSI storage to the router, based on the iSCSI qualified name (iqn) or the IP address.

3. Set the Time To Target Device Offline system parameter to 60, using the set system command.

For access control information, refer to your iSCSI storage documentation.

Configuration OverviewAfter connecting the router Fibre Channel ports in the SAN and the gigabit Ethernet (GbE) ports in the LAN, follow these five basic steps:

“Step 1: Discover the iSCSI Targets” on page 5-2:

Using the iSCSI Discover Command

Using iSNS Server Connectivity

“Step 2: Log into the iSCSI Targets” on page 5-6

“Step 3: Zone the Fibre Channel Host and iSR6200 Router” on page 5-6

“Step 4: Map the iSCSI Target into the SAN and Provide Host Access to the Storage LUN” on page 5-7

“Step 5: View the Newly Mapped Target Zoned to the Fibre Channel Host” on page 5-9

These steps are described in detail in the following sections.

5–Configuring Fibre Channel Initiators to iSCSI Storage

Configuration Overview

5-2 ISR654601-00 E

Step 1: Discover the iSCSI TargetsThere are two ways to discover the iSCSI targets:

Using the iSCSI Discover Command

Using iSNS Server Connectivity

Using the iSCSI Discover Command1. Issue the show targets command. For example:

iSR6200 <1> (admin) #> show targets

No Targets found.

2. Issue the iscsi discover command. For example:

iSR6200 <1> (admin) #> iscsi discover

The first attribute appears with the current value (in brackets). Type a new value, or press the ENTER key to accept the current value. The next attribute with the current value appears.

To stop this process before reaching the end of the list, press the Q+ENTER keys.

In the following example, all the attributes are shown:

IP Address (IPv4 or IPv6) [0.0.0.0 ] 192.168.95.48


Outbound Port (1=GE1, 2=GE2, ...) [GE1 ] 3

Target CHAP (0=Enable, 1=Disable [Disabled ]

3. To see the target attributes, issue the show targets command. For example:

iSR6200 <1> (admin) #> show targets

Target Information

--------------------

iSCSI Name iqn.2001-05.com.equallogic:0-8a0906-7e33e0d06-83c835550264bede-demo1

Alias

State Offline

IP Address 192.168.95.105 (Logged Out)



ISR654601-00 E 5-3

Using iSNS Server Connectivity1. Allow the iSCSI storage access to the iSNS server iSCSI port and router

iSCSI ports. This access can be either IP based or iqn based. See your iSCSI storage documentation for access control information.

2. Configure the iSCSI ports on the router in the same domain as the iSNS server iSCSI port and array. To set the iSCSI attributes, issue the set iscsi command.

3. Check connectivity amongst the router iSCSI port, the iSNS server port, and the array port by issuing the ping command.

4. Connect to the iSNS server by following these steps:

a. Issue the set isns command. For example:

iSR6200 <1> (admin) #> set iSNS

The first attribute appears with the current value (in brackets).

b. Type a new value, or press the ENTER key to accept the current value.

The next attribute with the current value appears.


In the following example, all the attributes are shown:

iSNS (0=Enable, 1=Disable) [Disabled ] 0

iSNS Address (IPv4 or IPv6) [0.0.0.0 ] 192.168.95.100



5. Create, add, and enable a discovery domain and set as follows:

a. Log in to the server where the iSNS server is installed.

b. Refresh and confirm that both initiator (router) and target (array) iqn names are discovered.

c. Create a discovery domain and add to it both the initiator (router) and target (array), as shown in Figure 5-1.



5-4 ISR654601-00 E

Figure 5-1. iSNS Server Properties: Creating a Discovery Domain



ISR654601-00 E 5-5

d. Add this discovery domain to a set, and then enable this discovery domain set, as shown in Figure 5-2.

Figure 5-2. iSNS Server Properties: Enabling a Discovery Domain Set

6. List the discovered targets by issuing the show targets command.



5-6 ISR654601-00 E

Step 2: Log into the iSCSI TargetsIssue the iscsi login command, and then follow the prompts.

A list of attributes appear with the current value (in brackets). At the prompts, select the target and IP address, and then specify additional target attributes as needed. For example:

iSR6200 <1> (admin) #> iscsi login


----- ----------------------

0 iqn.2001-05.com.equallogic:0-8a0906-7e33e0d06-83c835550264bede-demo1


Index IP Address

----- ----------

0 192.168.95.48

Please select an IP Address from the list above ('q' to quit):


Outbound Port (1=GE1, 2=GE2, ...) [GE1 ] 3

Header Digest (0=Enable, 1=Disable) [Disabled ]

Data Digest (0=Enable, 1=Disable) [Disabled ]

iSCSI Login for selected target was successful


Step 3: Zone the Fibre Channel Host and iSR6200 RouterGet the following information to configure the iSR6200 to the Fibre Channel SAN and the connection to the EqualLogic array.

For the Fibre Channel SAN, create a list of fabric zones that contain the world wide port name (WWPN) associated with the servers by entering their values in Table 5-1.



ISR654601-00 E 5-7

Figure 5-3 shows a zone configured with the router to see the targets.

Figure 5-3. Zone Configured with Router

Step 4: Map the iSCSI Target into the SAN and Provide Host Access to the Storage LUN

This step maps the iSCSI target into the Fibre Channel SAN, and provides LUN access from the host to the storage. Be sure you select the correct iSR6200 Fibre Channel port to present to the target.

Table 5-1. Zone Host with Router—Fibre Channel-Based Ports

Fibre Channel Switch and IP

Address

Fibre Channel Zone Name

Zone Members (WWPNs)

Server, iSR6200, Storage Name



5-8 ISR654601-00 E

1. Issue the show initiators command. For example:

iSR6200 <1> (admin) #> show initiators

Initiator Information

-----------------------

WWNN 20:00:00:1b:32:9a:e7:5c

WWPN 21:00:00:1b:32:9a:e7:5c

Port ID 0b-05-00

Status Logged Out

Type FC

OS Type Windows2. Issue the lunmask add command, and then follow the prompts. For

example:



----- ---- ------ ----------------------

0 FC No 20:00:00:1b:32:9a:e7:5c,21:00:00:1b:32:9a:e7:5c



----- ----------------------

0 iqn.2001-05.com.equallogic:0-8a0906-7e33e0d06-83c835550264bede-demo1


Index (LUN/VpGroup)

----- -------------

0 0/VPGROUP_1


Index (IP/WWNN) (MAC/WWPN)

----- ----------- ------------

0 0.0.0.0 00-c0-dd-18-c9-88

1 0.0.0.0 00-c0-dd-18-c9-89

2 192.168.95.20 00-c0-dd-18-c9-8a

3 0.0.0.0 00-c0-dd-18-c9-8b

4 20:00:00:c0:dd:18:c9:88 21:00:00:c0:dd:18:c9:88

5 20:00:00:c0:dd:18:c9:89 21:00:00:c0:dd:18:c9:89

6 20:00:00:c0:dd:18:c9:8a 21:00:00:c0:dd:18:c9:8a

7 20:00:00:c0:dd:18:c9:8b 21:00:00:c0:dd:18:c9:8b



ISR654601-00 E 5-9

Please select a portal to map the target from the list above ('q' to quit): 5

All attribute values that have been changed will be saved.

Step 5: View the Newly Mapped Target Zoned to the Fibre Channel Host

This step identifies the mapping between an iSCSI target and a Fibre Channel or FCoE presented target. This step determines the correct Fibre Channel device to zone with the Fibre Channel host.

1. Issue the show presented_targets command to view the targets:

iSR6200 <1> (admin) #> show presented_targets


----------------------------

FC/FCOE Presented Targets

-------------------------

WWNN 20:04:00:c0:dd:18:c9:89

WWPN 21:04:00:c0:dd:18:c9:89

Port ID 03-01-02

Port FC2

Type FC

NOTE:

In the preceding code, the numbers in the last Index column correspond to the following ports:

Index Port

0 GE1

1 GE2

2 10GE1

3 10GE2

4 FC1

5 FC2

6 FCoE1 or FC3

7 FCoE2 or FC4



5-10 ISR654601-00 E

<MAPS TO>

Name iqn.2001-05.com.equallogic:0-8a0906-7e33e0d06-83c835550264bede-demo1

Figure 5-4 shows that the zone of the newly mapped target is configured with the iSR6200 router to the Fibre Channel SAN.

Figure 5-4. iSCSI Configured with Router to Fibre Channel SAN

2. After the server discovers the storage and I/O has started, issue the show perf byte command to determine what I/O is operational on the selected ports. For example:

iSR6200 <1> (admin) #> show perf byte

WARNING: Valid data is only displayed for port(s) that are notassociated with any configured FCIP routes.

Displaying bytes/sec (total)... (Press any key to stop display)

GE1 GE2 10GE1 10GE2 FC1 FC2 FC3 FC4

-------------------------------------------------------------

0 0 102M 0 0 109M 0 0

0 0 106M 0 0 104M 0 0

ISR654601-00 E A-1

A Simple Network Management Protocol

Simple network management protocol (SNMP) provides monitoring and trap functions for managing the router through third-party applications that support SNMP. The router firmware supports SNMP versions 1 and 2, and a QLogic management information base (MIB) (see page A-4). You may format traps using SNMP version 1 or 2.

This appendix provides the following SNMP information for the iSR6200:

“SNMP Parameters” on page A-2

“SNMP Trap Configuration” on page A-3

“Management Information Base (MIB)” on page A-4

“Notifications” on page A-19

A–Simple Network Management Protocol

SNMP Parameters

A-2 ISR654601-00 E

SNMP ParametersYou can set the SNMP properties using SANsurfer Router Manager or the command line interface (CLI).

Table A-1 describes the SNMP parameters.

Table A-1. SNMP Parameters

Parameter Description

Read community A password that authorizes an SNMP management server to read information from the router. This is a write-only field. The value on the router and the SNMP management server must be the same. The read community password can be up to 32 characters, excluding the number sign (#), semicolon (;), and comma (,). The default password is private.

Trap community A password that authorizes an SNMP management server to receive traps. This is a write-only field. The value on the router and the SNMP management server must be the same. The trap community password can be up to 32 char-acters, excluding the number sign (#), semicolon (;), and comma (,). The default password is private.

System location

Specifies the name of the router location. The name can be up to 64 characters, excluding the number sign (#), semicolon (;), and comma (,). The default is undefined.

System contact Specifies the name of the person to be contacted to respond to trap events. The name can be up to 64 characters, excluding the number sign (#), semicolon (;), and comma (,). The default is undefined.

Authentication traps

Enables or disables the generation of authentication traps in response to authentication failures. The default is disabled.


SNMP Trap Configuration

ISR654601-00 E A-3

SNMP Trap ConfigurationSNMP trap configuration lets you set up to eight trap destinations. Choose from Trap 1 through Trap 8 to configure each trap. Table A-2 describes the parameters for configuring an SNMP trap.

Table A-2. SNMP Trap Configuration Parameters

Parameter Description

Trap n enabled

Enables or disables trap n. If disabled, the trap is not configured.

Trap address* Specifies the IP address to which the SNMP traps are sent. A maximum of eight trap addresses are supported. The default address for traps is 0.0.0.0.

Trap port* Port number on which the trap is sent. The default is 162. If the trap destination is not enabled, this value is 0 (zero). Most SNMP managers and management software listen on this port for SNMP traps.

Trap version Specifies the SNMP version (1 or 2) with which to format traps.

Table Note

* Trap address (other than 0.0.0.0.) and trap port combinations must be unique. For example, if trap 1 and trap 2 have the same address, they must have different port values. Similarly, if trap 1 and trap 2 have the same port value, they must have different addresses.


Management Information Base (MIB)

A-4 ISR654601-00 E

Management Information Base (MIB)This section describes the QLogic MIB. The MIB includes the following tables:

“Network Port Table” on page A-4 “Fibre Channel Port Table” on page A-7 “Initiator Object Table” on page A-9 “LUN Table” on page A-12 “Virtual Port Group Table” on page A-14 “Sensor Table” on page A-16

Network Port TableThe network port table contains a list of network ports that are operational on the router. The entries in this table include the management port (labeled MGMT), and the Gigabit Ethernet ports (labeled GE1 and GE2). For details, see the iSR6200 Intelligent Storage Router Installation Guide.

qsrNwPortTable

qsrNwPortEntry

Syntax SEQUENCE OF QsrNwPortEntry

Access Not accessible

Description Entries in this table include the management port, and the iSCSI ports on the router.

Syntax QsrNwPortEntry


Description Each entry (row) contains information about a specific net-work port.



ISR654601-00 E A-5

A network port entry includes the following sequence of objects:

qsrNwPortRole QsrPortRole

qsrNwPortIndex unsigned32

qsrNwPortAddressMode INTEGER

qsrIPAddressType InetAddressType

qsrIPAddress InetAddress

qsrNetMask InetAddress

qsrGateway InetAddress

qsrMacAddress MacAddress

qsrNwLinkStatus QsrLinkStatus

qsrNwLinkRate QsrLinkRate

qsrNwPortRole

qsrNwPortIndex

qsrNwPortAddressMode

Syntax QsrPortRole


Description Operational role of this port: management port or iSCSI port.

Syntax Unsigned32


Description A positive integer indexing each network port in a specified role.

Syntax INTEGER1 = Static2 = DHCP3 = Bootp4 = RARP

Access Read-only

Description Method by which the port gets its IP address.



A-6 ISR654601-00 E

qsrIPAddressType

qsrIPAddress

qsrNetMask

qsrGateway

qsrMacAddress

qstNwLinkStatus

Syntax InetAddressType

Access Read-only

Description IP address type: ipv4 or ipv6.

Syntax InetAddress

Access Read-only

Description IP address of the port.

Syntax InetAddress

Access Read-only

Description Subnet mask for this port.

Syntax InetAddress

Access Read-only

Description Gateway for this port.

Syntax IMacAddress

Access Read-only

Description MAC address for this port.

Syntax QsrLinkStatus

Access Read-only

Description Operational link status for this port.



ISR654601-00 E A-7

qsrNwLinkRate

Fibre Channel Port TableThis table contains a list of the Fibre Channel (FC) ports on the router. There are as many entries in this table as there are Fibre Channel ports on the router.

qsrFcPortTable

qsrFcPortEntry

A Fibre Channel port entry consists of the following sequence of objects:

qsrFcPortRole QsrPortRole

qsrFcPortIndex Unsigned32

qsrFcPortNodeWwn PhysAddress

qsrFcPortWwn PhysAddress

qsrFcPortId PhysAddress

qsrFcPortType Unsigned32

qsrFcLinkStatus QsrLinkStatus

qsrFcLinkRate QsrLinkRate

Syntax QsrLinkRate

Access Read-only

Description Operational link rate for this port.

Syntax SEQUENCE OF QsrFcPortEntry


Description A list of the Fibre Channel ports on the router. The table contains as many entries as there are Fibre Channel ports on the router.

Syntax QsrFcPortEntry


Description Each entry (row) contains information about a specific Fibre Channel port.



A-8 ISR654601-00 E

qsrFcPortRole

qsrFcPortIndex

qsrFcPortNodeWwn

qsrFcPortWwn

qsrFcPortId

Syntax QsrPortRole


Description Operational role of this port: Fibre Channel protocol (FCP) mode or frame shuttle mode.

Syntax Unsigned32


Description A positive integer indexing each Fibre Channel port in a specified role.

Syntax PhysAddress

Access Read-only

Description World wide name of the node that contains this port.

Syntax PhysAddress

Access Read-only

Description World wide name for this port.

Syntax PhysAddress

Access Read-only

Description Interface's 24-bit Fibre Channel address identifier.



ISR654601-00 E A-9

qsrFcPortType

qsrFcLinkStatus

qsrFcLinkRate

Initiator Object TableThe initiator object table is a list of the iSCSI initiators that have been discovered by the router. There are as many entries in this table as there are iSCSI initiators on the router.

qsrIsInitTable

Syntax Unsigned32

Access Read-only

Description Type of Fibre Channel port, as indicated by the use of the appropriate value assigned by the Internet Assigned Num-bers Authority (IANA). The Fibre Channel port types regis-try maintained by IANA is located here:

www.iana.org/assignments/fc-port-types

Syntax QsrLinkStatus

Access Read-only

Description Current link status for this port.

Syntax QsrLinkRate

Access Read-only

Description Current link rate for this port.

Syntax SEQUENCE OF QsrIsInitEntry


Description Entries in this table contain information about initiators.

http://www.iana.org/assignments/fc-port-types



A-10 ISR654601-00 E

qsrIsInitEntry

iSCSI initiator information entry consists of the following sequence of objects:

qsrIsInitIndex Unsigned32,

qsrIsInitName SnmpAdminString,

qsrIsInitAlias SnmpAdminString,

qsrIsInitAddressType InetAddressType,

qsrIsInitAddress InetAddress,

qsrIsInitStatus INTEGER,

qsrIsInitOsType SnmpAdminString,

qsrIsInitChapEnabled INTEGER

qsrIsInitIndex

qsrIsInitName OBJECT-TYPE

qsrIsInitAlias OBJECT-TYPE

Syntax QsrIsInitEntry


Description Each entry (row) contains information about a specific iSCSI initiator.

Syntax Unsigned32


Description An arbitrary, positive integer denoting each iSCSI initiator discovered by the router.

Syntax SnmpAdminString


Description iSCSI name of the initiator.


Access Read-only

Description Alias for the iSCSI initiator.



ISR654601-00 E A-11

qsrIsInitAddressType

qsrIsInitAddress

qsrIsInitStatus

qsrIsInitOsType

qsrIsInitChapEnabled

Syntax InetAddressType

Access Read-only

Description Type of iSCSI initiator’s IP address (IPv4 or IPv6).

Syntax InetAddress

Access Read-only

Description IP address of the iSCSI initiator.

Syntax Integer:1 = unknown,2 = loggedIn,3 = loggedOut,4 = recovery

Access Read-only

Description Status of the iSCSI initiator, that is, whether or not it is logged in to the router.


Access Read-only

Description The type of the iSCSI initiator’s operating system.

Syntax Integer: 0 = enabled; 2 = disabled

Access Read-only

Description A value indicating whether CHAP is enabled or not for this iSCSI initiator.



A-12 ISR654601-00 E

LUN TableThese tables contains information about the logical unit number (LUN) list.

qsrLunTable

qsrLunEntry

The QsrLunEntry contains the following sequence of objects:

qsrLunWwuln PhysAddress,

qsrLunVendorId SnmpAdminString,

qsrLunProductId SnmpAdminString,

qsrLunProdRevLevel SnmpAdminString,

qsrLunSize Unsigned32,

qsrLunState INTEGER,

qsrLunVPGroupid INTEGER,

qsrLunVPGroupname SnmpAdminString

qsrLunWwuln

Syntax SEQUENCE OF QsrLunEntry


Description A list of the LUNs on the Fibre Channel targets discovered by the router. There are as many entries in this table as there are Fibre Channel targets on the router.

Syntax QsrLunEntry


Description Each entry (row) contains information about a specific LUN. This table extends scsiDscLunTable in QLOGIC-SCSI-MIB. The entries in this table show other attributes of the LUN.

Syntax PhysAddress

Access Read-only

Description The world wide unique LUN name (WWULN) for the LUN.



ISR654601-00 E A-13

qsrLunVendorId

qsrLunProductId

qsrLunProdRevLevel

qsrLunSize OBJECT-TYPE

qsrLunState


Access Read-only

Description Vendor ID for the LUN.


Access Read-only

Description Product ID for the LUN.


Access Read-only

Description Product revision level for the LUN.

Syntax Unsigned32

Units Megabytes

Access Read-only

Description Size of the LUN (in megabytes).

Syntax Integer1 = online,2 = offline,3 = reserved

Access Read-only

Description State of the LUN (online or offline).



A-14 ISR654601-00 E

qsrLunVPGroupid

qsrLunVPGroupname OBJECT-TYPE

Virtual Port Group TableThis table contains a list of virtual port groups. There are four entries in this table at any point of time.

qsrVPGroupTable

qsrVPGroupEntry OBJECT-TYPE

Syntax Integer

Access Read-only

Description ID of the virtual port group to which this LUN belongs.


Access Read-only

Description Virtual port group name to which this LUN belongs.

Syntax SEQUENCE OF QsrVPGroupEntry


Description Table for the virtual port group.

Syntax QsrVPGroupEntry


Description Each entry in the virtual port group table.

Index { qsrVPGroupIndex }::= { qsrVPGroupTable 1 }



ISR654601-00 E A-15

The QsrVPGroupEntry contains the following sequence of objects:

qsrVPGroupIndex Unsigned32,

qsrVPGroupId INTEGER,

qsrVPGroupName SnmpAdminString,

qsrVPGroupWWNN VpGroupWwnnAndWwpn,

qsrVPGroupWWPN VpGroupWwnnAndWwpn,

qsrVPGroupStatus INTEGER

qsrVPGroupIndex OBJECT-TYPE

qsrVPGroupId OBJECT-TYPE

qsrVPGroupName

qsrVPGroupWWNN

Syntax Unsigned32

Access Read-only

Description Virtual port group index.

Syntax Integer

Access Read-only

Description Virtual port group ID.


Access Read-only

Description Virtual port group name or host group name.

Syntax VpGroupWwnnAndWwpn

Access Read-only

Description World wide node name (WWNN) for the virtual port group.



A-16 ISR654601-00 E

qsrVPGroupWWPN OBJECT-TYPE

qsrVPGroupStatus OBJECT-TYPE

Sensor TableThe sensor table lists all the sensors on the router. Each table row specifies a single sensor.

qsrSensorTable

qsrSensorEntry

Syntax VpGroupWwnnAndWwpn

Access Read-only

Description World wide port number (WWPN).

Syntax Integer: 0 = enabled; 1 = disabled

Max-Access Read-only

Description Maintain the status of the virtual port group (enabled/dis-abled)

Syntax SEQUENCE OF QsrSensorEntry


Description List of all the sensors on the router. The table contains as many entries (rows) as there are sensors.

Syntax QsrSensorEntry


Description Each entry (row) corresponds to a single sensor.



ISR654601-00 E A-17

A sensor entry contains the following sequence of objects:

qsrSensorType INTEGERqsrSensorIndex Unsigned32qsrSensorUnits INTEGERqsrSensorValue Integer32qsrUpperThreshold Integer32qsrLowerThreshold Integer32qsrSensorState INTEGER

qsrSensorType

qsrSensorIndex

qsrSensorUnits

qsrSensorValue

Syntax INTEGERTemperature = 1


Description Type of data being measured by this sensor.

Syntax Unsigned32


Description A positive integer identifying each sensor of a specified type.

Syntax INTEGERCelsius = 1

Access Read-only

Description Unit of measurement for the sensor.

Syntax Integer32

Access Read-only

Description Current value of the sensor.



A-18 ISR654601-00 E

qsrUpperThreshold

qsrLowerThreshold

qsrSensorState

Syntax Integer32

Access Read-only

Description Upper-level threshold for this sensor.

Syntax Integer32

Access Read-only

Description Lower-level threshold for this sensor.

Syntax INTEGER

Access Read-only

Description State of this sensor, indicating the health of the system:Unknown = The sensor value/thresholds cannot be deter-mined.Normal = The sensor value is within normal operational limits.Warning = The sensor value is approaching a threshold.Critical = The sensor value has crossed a threshold.


Notifications

ISR654601-00 E A-19

NotificationsThe router provides the following notification types described in this section:

“System Information Objects” on page A-19 “Notification Objects” on page A-20 “Agent Startup Notification” on page A-21) “Agent Shutdown Notification” on page A-21 “Network Port Down Notification” on page A-21 “Fibre Channel Port Down Notification” on page A-22 “Target Device Discovery” on page A-22 “Target Presentation (Mapping)” on page A-22 “Virtual Port Group Notification” on page A-23 “Sensor Notification” on page A-23 “Generic Notification” on page A-24 “FCIP Route Notification” on page A-25

System Information ObjectsThe system information objects provide the system serial number, version numbers (hardware, software, and agent), and number of ports (Fibre Channel and GbE).

qsrSerialNumber

qsrHwVersion

NOTE:

Every notification uses qsrBladeSlot as one of the objects. This determines the originator blade for the same notification.


Access Read-only

Description System serial number.


Access Read-only

Description System hardware version number.


Notifications

A-20 ISR654601-00 E

qsrSwVersion

qsrNoOfFcPorts

qsrNoOfGbEPorts

qsrAgentVersion

Notification ObjectsThis section defines the objects used in notifications.

qsrEventSeverity


Access Read-only

Description System software (firmware) version number.

Syntax Unsigned32

Access Read-only

Description Quantity of Fibre Channel ports on the system.

Syntax Unsigned32

Access Read-only

Description Quantity of gigabit Ethernet ports on the system.


Access Read-only

Description Version number of the agent software on the system.

Syntax INTEGER

Access Accessible for notify

Description Indicates the severity of the event. The value clear specifies that a condition that caused an earlier trap is no longer present.


Notifications

ISR654601-00 E A-21

qsrEventDescription

qsrEventTimeStamp

Agent Startup NotificationThe agent startup notification indicates that the agent on the router has started running.

qsrAgentStartup uses the following object:

qsrEventTimeStamp

Agent Shutdown NotificationThe agent shutdown notification indicates that the agent on the router is shutting down.

qsrAgentShutdown uses the following object:

qsrEventTimeStamp

Network Port Down NotificationThe network port down notification indicates that the specified network port is down. The next time the port comes up, this event is sent with the qsrEventSeverity object set to clear.

qsrNwPortDown uses the following objects:

qsrNwLinkStatus qsrEventTimeStamp qsrEventSeverity

Network notifications are sent for the following events:

Management port: down or up iSCSI port: down or up Port number (1–4)



Description A textual description of the event that occurred.

Syntax DateAndTime


Description Indicates when the event occurred.


Notifications

A-22 ISR654601-00 E

Fibre Channel Port Down NotificationThe Fibre Channel port down notification indicates that the specified Fibre Channel port is down. The next time the port comes up, this event is sent with the qsrEventSeverity object set to clear.

qsrFcPortDown uses the following objects:

qsrFcLinkStatus qsrEventTimeStamp qsrEventSeverity

Fibre Channel notifications are sent for the following events:

Fibre Channel port: down or up Port number (1–4)

Target Device DiscoveryThe Fibre Channel target device discovery notification indicates that the specified Fibre Channel target is online or offline.

qsrDscTgtStatusChanged uses the following objects:

qsrBladeSlot qsrEventTimeStamp qsrFcTgtState qsrEventSeverity

Fibre Channel target device discovery notifications are sent for the following event:

Fibre Channel Target

State: Discovered, went offline, or went online Target WWPN Blade number (1 or 2)

Target Presentation (Mapping)The target presentation notification indicates that the specified target has been presented (mapped) or unpresented (unmapped).

qsrPresTgtMapped uses the following objects:

qsrBladeSlot qsrEventTimeStamp qsrPresTgtMapped qsrPresTgtUnmapped qsrEventSeverity

Target presentation notifications are sent for the following event:


Notifications

ISR654601-00 E A-23

Target Presentation

State: Presented (mapped) or unpresented (unmapped) Target name Blade number (1 or 2)

Virtual Port Group NotificationThe virtual port group notification indicates that the specified virtual port group is enabled or disabled. It also represents change in the name of the virtual port group.

qsrVPGroupStatusChanged uses the following objects:

qsrBladeSlot qsrVPGroupIndex qsrVPGroupStatus qsrEventTimeStamp qsrEventSeverity

virtual port group notifications are sent for the following events:

Change in name of a virtual port group Enabling and disabling a virtual port group

Sensor NotificationThe sensor notification indicates that the state for the specified sensor is not normal. When the sensor returns to the normal state, this event is sent with the qsrEventSeverity object set to clear.

qsrSensorNotification uses the following objects:

qsrSensorValue qsrSensorState qsrEventTimeStamp qsrEventSeverity

Sensor notifications are sent for the following events:

Over Temperature

Blade number (1 or 2) Sensor number (1 of 3)

Temperature returned to normal

Blade number (1 or 2) Sensor number (1 of 3)


Notifications

A-24 ISR654601-00 E

Fans at high speed

Power and cooling module (PCM) number (1 or 2)

Fans returned to normal speed

PCM number (1 or 2)

(PCM) installed

PCM number (1 or 2)

PCM removed

PCM number (1 or 2)

PCM powered (AC power connected)

PCM number (1 or 2)

PCM un-powered (AC power removed)

PCM number (1 or 2)

Fan failed

PCM number (1 or 2) Fan number (1 of 3)

Fan returned to operational state

PCM number (1 or 2) Fan number (1 of 3)

Generic NotificationThe generic notification reports events other than the defined event types. It provides a description object that identifies the event in clear text.

qsrGenericEvent uses the following objects:

qsrEventTimeStamp qsrEventSeverity qsrEventDescription

Generic notifications are sent for the following events:

Fibre Channel port configuration change

Blade number (1 or 2) Port number (1 of 4)

iSCSI port configuration change


Notifications

ISR654601-00 E A-25

Blade number (1 or 2) Port number (1 of 4)

iSNS configuration change

Blade number (1 or 2)

NTP configuration change


Router configuration change


Management port configuration change


Firmware upgrade complete


Reboot blade


FCIP Route NotificationFCIP route notification indicates whether the route has been added, removed, or modified. It is a user-action driven trap.

qsrFCIPRouteNotification uses the following objects:

qsrFcipRouteIndex qsrFCIPRouteAction qsrEventTimeStamp qsrEventSeverity qsrBladeSlot

FCIP Link Up and Link Down are notified with a generic notification that contains a user-level string, either FcipRoute#%d: FCIP Link Up or FcipRoute#%d: FCIP Link Down.


Notifications

A-26 ISR654601-00 E

ISR654601-00 E B-1

B Log Messages

This appendix provides details about messages logged to a file. The message log is persistent because it is maintained across router power cycles and reboots.

Information in Table B-1 is organized as follows:

The ID column specifies the message identification numbers in ascending order.

The Log Message column indicates the message text shown in the CLI or SANsurfer Router Manager router log. Note that:

Log messages for the iSCSI driver module are common to both iSCSI ports. Log messages beginning with #0 denote iSCSI port 1 (GE1) and log messages beginning with #1 denote iSCSI port 2 (GE2).

Log messages for the Fibre Channel driver module are common to both Fibre Channel ports. Log messages beginning with #0 denote Fibre Channel port 1 (FC1), and log messages beginning with #1 denote Fibre Channel port 2 (FC2).

Log messages for the FCIP module are common to both FCIP routes. Log messages beginning with #0 denote FCIP route 1, and log messages beginning with #1 denote FCIP route 2.

The Module Type column specifies the message reporting module, where:

App = Application module FC = Fibre Channel driver FCIP = FCIP driver iSCSI = iSCSI driver

B–Log Messages

B-2 ISR654601-00 E

NIC = FCIP NIC module System = System module User = User module

The Msg. Type column specifies the log message type, where:

Error = Error log message Fatal = Fatal log message Info = Informational log message

The Description column provides additional information about the log message.

Table B-1. iSR6200 Router Log Messages

ID Log Message Module Type

Msg. Type Description

40967 QLBA_NullDoorbell: driver unloaded, port disabled

App Error NULL doorbell routine for unloaded drivers. When a driver is unloaded, the doorbell routine is redirected to this NULL routine.

40996 QLBA_ProcessTrb: Processing unsupported ordered tag command

App Error Processing unsupported ordered tag task manage-ment command.

41004 QLBA_ProcessTrb: Processing unsupported head of queue tag command

App Error Processing unsupported head-of-queue task man-agement command.

41058 QLBA_CreateTargetDeviceObject: Too many devices

App Error Unable to create an object for the target device; exceeded the maximum number of target devices.

41060 QLBA_CreateTargetNodeObject: Too many devices

App Error Unable to create an object for the target node; exceeded the maximum number of target devices.

41067 QLBA_CreateLunObject: LunObject memory unavailable

App Error Memory unavailable for LUN object.

B–Log Messages

ISR654601-00 E B-3

41077 QLBA_CreateInitiatorObject: Too many initiators

App Error Unable to create an object for initiator object; exceeded the maximum number of initiators.

41096 QLBA_DisplayTargetOperationStatus: PCI Error, Status 0x%.2x

App Error Process control block status indicates that a periph-eral component interface/interconnect (PCI) error occurred during a target operation.

41106 QLBA_DisplayInitiatorOperationStatus: DMA Error, Status 0x%.2x

App Error Process control block status indicates that a direct memory access (DMA) error occurred during an initi-ator operation.

41107 QLBA_DisplayInitiatorOperationStatus: Transport Error, Status 0x%.2x

App Error Process control block status indicates that a transport error (protocol) occurred during an initiator operation.

41111 QLBA_DisplayInitiatorOperationStatus: Data Overrun, Status 0x%.2x

App Error Process control block status indicates that a data overrun error occurred during an initiator operation.

41234 QLIS_LoginPduContinue: Operation failed. Initiator 0x%x, TPB status 0x%x

App Error iSCSI login failed between receipt of protocol data unit (PDU) and request for the data segment.

41238 QLKV_ValidateLoginTransitCsgNsgVersion failed (status 0x%x)

App Error iSCSI login failed due to unsupported version number in received login PDU.

41257 QLIS_LoginPduContinue: Invalid initiator name. Initiator:

App Error iSCSI Login PDU contains invalid initiator name. The format and character set used to form the initiator name is invalid.

41265 QLIS_LoginPduContinue: Target not configured for Portal

App Error iSCSI target login was attempted to a portal (iSCSI1 or iSCSI2) on which the target is not presented.

41267 QLIS_LoginPduContinue: Target not found. Target name:

App Error iSCSI Login PDU received for a target with a target name unknown to the router.

Table B-1. iSR6200 Router Log Messages (Continued)



B–Log Messages

B-4 ISR654601-00 E

41268 QLIS_LoginPduContinue: Missing target name

App Error iSCSI Login PDU received without a target name for a normal session.

41270 QLIS_LoginPduContinue: TSIH is 0 but InitiatorName key/value not provided

App Error iSCSI Login PDU received without an initiator name key/value.

41272 QLIS_LoginPduContinue: CONN_STATE_IN_LOGIN, Unknown InitTaskTag

App Error iSCSI Login PDU received with an incorrect initiator task tag for a session that is partially logged in. This would occur if a login PDU other than the initial login PDU used an initiator task tag that was different from the initiator task tag provided in the initial login PDU.

41283 QLIS_LoginPduContinue: TSIH 0x%x out of range

App Error iSCSI login PDU was received with a target session identifying handle (TSIH) out of range. This would occur if the iSCSI initiator attempting the login failed to used the TSIH value provided in the Target Login Response PDU (router is target) in subsequent login PDUs.

41284 QLIS_LoginPduContinue: Session does not exist, invalid TSIH 0x%x

App Error iSCSI Login PDU was received with an invalid TSIH value. The TSIH is invalid because there is no ses-sion with that TSIH value. This would occur if the iSCSI initiator attempting the login failed to used the TSIH value provided in the target login response PDU (router is target) in subsequent login PDUs.

41353 QLIS_LoginPduContinue: Session does not exist, invalid TSIH 0x%x

App Error iSCSI Login rejected due to a CHAP authentication error.

41354 QLIS_LoginPduContinue: Unexpected CHAP key detected

App Error iSCSI Login rejected due to a CHAP key error.




B–Log Messages

ISR654601-00 E B-5

41508 QLBI_SetPortInfo: QLUT_AllocatePortalObject failed (PortType 0x%x, PortId 0x%x)

App Error Failed to allocate an object for Set Port Info IOCTL processing:

PortType: 0 = Fibre Channel, 1 = iSCSIPortId: 0 = FC1 or iSCSI1(GE1), 1 = FC2 or iSCSI2 (GE2)

41626 QLBI_GetLunInfo: INQUIRY failed, TPB status 0x%x

App Error Inquiry command failed. The Inquiry command was issued by the router as part of its discovery process.


App Error Pass-Through command for Inquiry command for page 83 failed. The Inquiry command was issued by the router as part of its discovery process.

41635 QLBI_Passthru: Invalid data length %d bytes

App Error Pass-Through command for Read Capacity com-mand failed. The Read Capacity command was issued by the router as part of its discovery process.


App Error Read Capacity command failed. The Read Capacity command was issued by the router as part of its dis-covery process.


App Error Pass-Through command issued by management tool (such as GUI) was aborted.

41700 QLBI_Passthru: Invalid CDB length %d bytes

App Error Pass-Through command issued by management tool (such as GUI) failed due to invalid command descrip-tor block (CDB) length.


App Error Pass-Through command issued by management tool (such as GUI) failed due to invalid data length.




B–Log Messages

B-6 ISR654601-00 E


App Error Pass-Through command issued by management tool (such as GUI) was interrupted or timed out.

41750 QLBI_Ioctl: ERROR: Operation (0x%x) not supported in this mode

App Error IOCTL operation unsupported. Operation code pro-vided in log message.

41768 QLBI_GetLunList: REPORT LUNS command failed

App Error Report LUNs command failed. The Report LUNs command was issued by the router as part of its dis-covery process.

41769 QLBI_GetLunList: REPORT LUNS command failed with CHECK CONDITION, SCSI STATUS 0x%02X

App Error Report LUNs command failed with check condition status. The Report LUNs command was issued by the router as part of its discovery process.

41771 QLBI_GetLunList: Lun allocation failed for LunId %d

App Error Failed to allocate LUN object; out of resources.

41994 QLFC_Login: VpIndex (%d) out of range App Error Login attempted using Fibre Channel virtual port (VP) index that is out-of-range (range = 0–31). Index reported in log message.

41995 QLFC_Login: VP Index 0x%x not configured App Error Login attempted using Fibre Channel VP index that has not been configured. Operation attempted on an unconfigured VP.

42002 QLFC_Login: Can't open connection App Error Attempting login but Fibre Channel connection can-not be opened.

42024 QLFC_Logout: No active path to device. WWPN:%.2X%.2X%.2X%.2X%.2X%.2X%.2X%.2X

App Error Attempting logout of device for which there is no active path (WWPN not found).




B–Log Messages

ISR654601-00 E B-7

42027 QLFC_Logout: VP Index 0x%x not configured App Error Logout attempted using Fibre Channel VP index that has not been configured. Operation attempted on an unconfigured VP.

42068 QLFC_HandleTeb: System Error App Error Event notification; Fibre Channel processor encoun-tered a system error (unrecoverable firmware error).

42069 QLFC_HandleTeb: Driver Fatal Error App Error Event notification; Fibre Channel driver encountered a fatal error.

42072 QLFC_HandleTeb: Driver Fatal Error App Error Event notification; Fibre Channel port logged out.

42242 QLIS_AllocateSessionObject: Out of session resources

App Error Failed to allocate object for iSCSI session; out of ses-sion resources.

42252 QLIS_EnqueueiScsiPdu: Duplicate PDU, CmdSN %d (0x%x), dropping it

App Error Received iSCSI PDU with duplicate command sequence number (CmdSN). Command PDU will be dropped.

42258 QLIS_InstantiateSession: Can't add Initiator to the database

App Error Unable to allocate iSCSI initiator object while instanti-ating session.

42259 QLIS_InstantiateSession: Maximum number (%d) of allowed hosts already logged in

App Error iSCSI session login rejected because the maximum number of allowed hosts are already logged in.

42404 QLIS_InstantiateSession: Maximum number (%d) of allowed hosts already logged in

App Error Failed to execute iSCSI Command PDU because its CmdSN is out-of-range. Log message contains the incorrect CmdSN, the valid CmdSN range, the first byte of the CDB, and the data length.

42648 QLIS_HandleTeb: Driver Fatal Error App Error Event notification; iSCSI driver encountered a fatal error.




B–Log Messages

B-8 ISR654601-00 E

42649 QLIS_HandleTeb: Unload Driver App Error Event notification; an IOCTL request was received to unload the iSCSI driver.

42654 QLIS_HandleTeb: iSNS Connection Failed App Error Event notification; attempt to connect to the iSNS server failed.

43265 QLUT_AllocateTpbExtension: TPB allocation failed

App Error Failed to allocate memory for TPB extension.

43267 QLUT_AllocateTpbExtension: Alloc of DSD failed for buffer len %d

App Error Failed to allocate data segment descriptor (DSD) (buffer length %d).

43268 QLUT_AllocateTpbExtension: Data buffer allocation failed (length %d)

App Error Failed to allocate data buffer (length %d).

44549 QLDM_HandleMigError: Migration Job %d stopped for Src Lun %hd Dest Lun %hd Error %x AdditionalErrorStatus %x at line %d

App Error An error occurred on an I/O that was issued for a migration job. The message provides the job ID, source, and destination LUN IDs, as well as the error.

53254 System Booting Up. App Info Router is booting up.

53357 QLBA_ProcessTpb: De-compression failed. Disabling compression temporarily

App Info Decompression failed. Disabling compression tem-porarily.

53584 QLIS_LoginPduContinue: [0x%x] SES_STATE_LOGGED_IN NORMAL

App Info iSCSI session full feature login.

53585 QLIS_LoginPduContinue: [0x%x] SES_STATE_LOGGED_IN DISCOVERY

App Info iSCSI session discovery login.

53586 QLIS_LoginPduContinue: Initiator: %s App Info iSCSI login of Initiator: %s.

53587 QLIS_LoginPduContinue: Target: %s App Info iSCSI login of Target: %s.




B–Log Messages

ISR654601-00 E B-9

54274 QLFC_Login: Origin 0x%x, VP Index 0x%x, Id 0x%x

App Info Fibre Channel login occurred, origin xx (1 = adapter, 2 = target, 3 = initiator), VP (virtual port) xx, ID (loop ID) xx.

54275 QLFC_Login: Port ID %.2x%.2x%.2x App Info Fibre Channel login occurred with port ID xx.xx.xx.

54276 QLFC_Login: Node Name %.2x%.2x%.2x%.2x%.2x%.2x%.2x%.2x

App Info Fibre Channel login occurred with WWNN xx.xx.xx.xx.xx.xx.xx.xx.

54277 QLFC_Login: Port Name %.2x%.2x%.2x%.2x%.2x%.2x%.2x%.2x

App Info Fibre Channel login occurred with WWPN xx.xx.xx.xx.xx.xx.xx.xx.

54306 QLFC_Logout: Origin 0x%x, VP Index 0x%x, Id 0x%x

App Info Fibre Channel Logout: Origin 0x%x, VP Index 0x%x, Id 0x%x.

54307 QLFC_Logout: Port ID %.2x%.2x%.2x App Info Fibre Channel Logout: Port ID %.2x%.2x%.2x.

54308 QLFC_Logout: Node Name %.2x%.2x%.2x%.2x%.2x%.2x%.2x%.2x

App Info Fibre Channel Logout: Node Name xx xx xx xx xx xx xx xx.

54309 QLFC_Logout: Port Name %.2x%.2x%.2x%.2x%.2x%.2x%.2x%.2x

App Info Fibre Channel Logout: Port Name xx xx xx xx xx xx xx xx.

54359 QLFC_Logout: Port Name %.2x%.2x%.2x%.2x%.2x%.2x%.2x%.2x

App Info Fibre Channel login event notification, VP (virtual port) xx.

54683 QLIS_OpenConnectionNotification: Target connection opened (Port %d, DDB %d)

App Info iSCSI target connection opened for port %d, data description block (DDB) %d.

54938 QLIS_OpenConnectionNotification: Target connection opened (Port %d, DDB %d)

App Info Event notification; iSCSI open connection request.




B–Log Messages

B-10 ISR654601-00 E

54939 QLIS_HandleTeb: UTM_EC_CLOSE_CONNECTION or UTM_EC_CONNECTION_CLOSED

App Info Event notification; iSCSI close connection request or connection closed.

54940 QLIS_HandleTeb: UTM_EC_CLOSE_CONNECTION or UTM_EC_CONNECTION_CLOSED

App Info Event notification; iSCSI connection closed.

54941 QLIS_HandleTeb:iSNS Server Open Connection succeeded

App Info Event notification; connection opened with iSNS server.

54943 QLIS_HandleTeb: UTM_EC_ISNS_SCN App Info Event notification; iSNS registered state change noti-fication (RSCN) received.

54945 QLIS_HandleTeb: UTM_EC_ISNS_CLIENT_DISCOVERED

App Info Event notification; iSNS client discovered.

56321 QLMP_Logout: Virtual Target Logged out App Info An array went offline because all the target ports of the array went offline.

56322 QLMP_Logout: Node Name %.2x%.2x%.2x%.2x%.2x%.2x%.2x%.2x

App Info WWNN of the array that went offline. This is tied with ID 56321.

56323 QLMP_Logout: Port Name %.2x%.2x%.2x%.2x%.2x%.2x%.2x%.2x

App Info WWPN of the array that went offline. This is tied with ID 56321.

56346 QLMP_CombineMPDevice: Virtual Target Online

App Info An array came online.

56347 QLMP_CombineMPDevice: Node Name %.2x%.2x%.2x%.2x%.2x%.2x%.2x%.2x

App Info WWNN of the array that came online. This is tied with ID 56346.

56348 QLMP_CombineMPDevice: Port Name %.2x%.2x%.2x%.2x%.2x%.2x%.2x%.2x

App Info WWPN of the array that came online. This is tied with ID 56346.




B–Log Messages

ISR654601-00 E B-11

56842 QLDM_ResumeMigration: Failed to resume job: %d, job's current state: 0x%x, error: %d

App Info Failed to resume a paused job.

56865 QLDM_DelayedStart:%d Failed to start job : Job ID: %d

App Info Failed to start a delayed schedule job.

56866 Lun is already used for of some other migration job

App Info Migration add failed because LUN is part of another migration job.

56867 Selected Lun is a Controller Lun App Info Migration being added with a LUN that is a controller LUN. Data LUNs are required for configuring migra-tion jobs.

56868 Selected Lun is Masked, It cant be used for Offline Migration

App Info Migration job being added for a LUN that is masked to an initiator on the router. Mapped LUNs cannot be used for offline migration jobs.

56869 Read Capacity is not available for the Lun App Info Migration job being added for a LUN for which no read capacity Information is available. Migration add will fail.

56870 QLDM_CreateMigrationObject: Failed to create Source Lun Object

App Info Failed to allocate memory for the source LUN of a migration job.

56871 QLDM_CreateMigrationObject: Failed to create Destination Lun Object

App Info Failed to allocate memory for the destination LUN of a migration job.

56872 QLDM_CreateMigrationObject: MigrationObject memory unavailable

App Info Failed to allocate memory for the migration job.




B–Log Messages

B-12 ISR654601-00 E

56880 Start time got from user %lu Cur Time: %lu Diff: %d

App Info The log shows the configured start time and current time for a delayed migration job.

56881 Failed to stop migration job id %u App Info Failed to stop a migration job; the error message includes the job ID.

56884 QLDM_DeleteMigrationJobByLun: Could not find migration object

App Info Did not find a migration job for the associated LUN object.

69652 #%d: qlutm_init: Diagnostic failed, invalid SRAM

iSCSI Fatal iSCSI processor SRAM test failed.

69653 #%d: qlutm_init: Diagnostic failed, fail reboot

iSCSI Fatal iSCSI processor failed diagnostic reboot.

69654 #%d: qlutm_init: Diagnostic failed, invalid NVRAM

iSCSI Fatal iSCSI processor failed NVRAM diagnostic.

69655 #%d: qlutm_init: Diagnostic failed, invalid DRAM

iSCSI Fatal iSCSI processor failed DRAM diagnostic.

69656 #%d: qlutm_init: Failed to return diagnostic result to Bridge

iSCSI Fatal iSCSI processor failed to return diagnostic results.

69941 #%d: QLUtmProcessResponseQueue: Invalid handle %x EntryType %x

iSCSI Fatal Response queue entry contains an invalid handle.

69951 #%d: QLSetNvram: QLRebootTimer failed AF %x RS %x Time %d

iSCSI Fatal Set NVRAM reboot timer failed.

69964 #%d: QLDisable: QLRebootTimer failed AF %x RS %x Time %d

iSCSI Fatal Port disable reboot timer failed.




B–Log Messages

ISR654601-00 E B-13

69966 #%d: QLEnable: QLRebootTimer failed AF %x RS %x Time %d

iSCSI Fatal Port enable reboot timer failed.

70224 #%d: QLProcSrblessiSNSResponse: Invalid handle %x

iSCSI Fatal iSNS response contains an invalid handle.

70400 #%d: QLInitializeDevice: QLStartAdapter failed

iSCSI Fatal Start iSCSI processor failed.

70417 #%d: QLInitializeAdapter: QLInitializeFW failed

iSCSI Fatal iSCSI processor firmware initialization failed.

70432 #%d: QLDoInterruptServiceRoutine: PortFatal interrupt. PortFatalErrorStatus %08x CSR %08x AS %x AF %x

iSCSI Fatal iSCSI processor port fatal error.

70448 #%d: QLStartAdapter: QLRebootTimer failed AF %x RS %x Time %d

iSCSI Fatal Start iSCSI processor reboot timer failed.

70489 #%d: QLIsrDecodeMailbox: System Error 8002 MB[1-7] %04x%04x %04x %04x %04x %04x %04x

iSCSI Fatal iSCSI processor fatal system error.

70499 #%d: QLProcessResponseQueue: Invalid handle for ET_PASSTHROUGH_STATUS

iSCSI Fatal Response queue invalid handle for ET pass-through.

70501 #%d: QLProcessResponseQueue: Invalid entry type in response queue %x

iSCSI Fatal Response queue invalid entry type.

70502 #%d: QLProcessResponseQueue: Invalid handle %x EntryType %x

iSCSI Fatal Response queue invalid handle for specified entry type.




B–Log Messages

B-14 ISR654601-00 E

70524 #%d: QLProcessAen: Invalid event %x iSCSI Fatal Asynchronous event for unknown event type.

70544 #%d: QLRebootTimer: Reboot failed! iSCSI Fatal Reboot timer failed.

70563 #%d: QLRebootTimer: Reboot failed! iSCSI Fatal iSCSI driver missed iSCSI processor heartbeat. iSCSI processor rebooted.

70564 #%d: QLRebootTimer: Reboot failed! iSCSI Fatal iSCSI processor failed to complete operation before timeout.

70609 #%d: QLRebootTimer: Reboot failed! iSCSI Fatal iSCSI processor system error restart.

70610 #%d: QLProcessSystemError: RebootHba failed

iSCSI Fatal iSCSI processor reboot failed.

70784 #%d: QLConfigChip: invalid NVRAM iSCSI Fatal iSCSI processor NVRAM invalid (checksum error).

70835 #%d: QLStartFw: MBOX_CMD_SET_FLASH failed %x

iSCSI Fatal iSCSI controller Set Flash command failed.

70836 #%d: QLStartFw: Invalid Fw loader state 0x%x

iSCSI Fatal iSCSI controller failed to load firmware.

70837 #%d: QLStartFw: Load Fw loader timeout iSCSI Fatal iSCSI controller firmware load operation timed out.

70938 #%d: ql_adapter_up: Failed to initialize adapter

iSCSI Fatal iSCSI controller failed to initialize.

72351 #%d: QLProcSrblessiSNSResponse: Invalid handle %x

iSCSI Fatal iSCSI controller reported that an SNS response had an invalid handle.

73990 #%d: QLUtmIoctlEnable: Initialize FW failed

iSCSI Error iSCSI processor failed firmware initialization.




B–Log Messages

ISR654601-00 E B-15

74056 #%d: QLRunDiag: MBOX Diag test internal loopback failed %x %x

iSCSI Error iSCSI processor failed the internal loopback test.

74057 #%d: QLRunDiag: MBOX Diag test external loopback failed %x %x

iSCSI Error iSCSI processor failed the external loopback test.

74068 #%d: QLUtmReceiveScsiCmd: Invalid ATIO Continuation type %x

iSCSI Error iSCSI processor reported an invalid Accept Target I/O (ATIO) Continuation type x.

74069 #%d: QLUtmProcessResponseQueue: Immediate data addr %08x:%08x in unsupported PduType

iSCSI Error iSCSI processor reported an Immediate data address (xxxxxxxx:xxxxxxxx) in an unsupported PDU Type.

74241 #%d: QLiSNSEnableCallback: iSNS Server TCP Connect failed

iSCSI Error iSCSI processor could not connect with the iSCSI name server (iSNS).

74577 #%d: QLIsrDecodeMailbox: NVRAM invalid iSCSI Error iSCSI processor reported that the iSCSI port NVRAM contains invalid data (checksum error).

74580 #%d: QLIsrDecodeMailbox: AEN %04x, Duplicate IP address detected, MB[1-5] %04x %04x %04x %04x %04x

iSCSI Error iSCSI processor reported a duplicate IP address was detected (address xxxx xxxx xxxx xxxx xxxx).

74587 #%d: QLIsrDecodeMailbox: Link down iSCSI Error iSCSI processor reported a link down condition.

74656 #%d: QLReadyTimer: Adapter missed heartbeat for %d seconds. Time left %d

iSCSI Error Driver failed to receive a heartbeat from the iSCSI processor for the specified number of seconds.

74659 #%d: QLReadyTimer: Adapter missed heartbeat for 0x%x seconds

iSCSI Error iSCSI processor (adapter) failed to provide a heart-beat for x seconds.

74660 #%d: QLReadyTimer: Abort pTpb=%p failed, DrvCount 0x%x

iSCSI Error iSCSI processor failed to complete an abort request.




B–Log Messages

B-16 ISR654601-00 E

74661 #%d: QLTimer: Abort pTpb=%p, Type %x, Timeout 0x%x DrvCount 0x%x, DdbIndex 0x%x

iSCSI Error Driver timed out an iSCSI processor operation and is aborting the operation.

74663 #%d: QLReadyTimer: MBOX_CMD %04x %04x %04x %04x%04x %04x %04x %04x timed out

iSCSI Error Driver timed out an iSCSI processor mailbox com-mand.

74665 #%d: QLReadyTimer: QLiSNSReenable failed. iSCSI Error Driver timed out while attempting to reconnect with the iSNS.

74705 #%d: QLProcessSystemError: Restart RISC iSCSI Error iSCSI processor was restarted.

74746 #%d: QLInitializeFW: MBOX_CMD_INITIALIZE_FIRMWARE failed %04x %04x %04x %04x %04x %04x

iSCSI Error iSCSI processor rejected the firmware initialize com-mand.

74784 #%d: QLUpdateInitiatorData: No more room in Initiator Database.

iSCSI Error Driver’s initiator database is full. The driver is capable of storing 1024 iSCSI initiators in its database. Use the CLI or GUI to remove unwanted/unused iSCSI initiators.

74800 #%d: QLSetTargetData: No more room in Target Database.

iSCSI Error Driver’s target database is full. Use the CLI or GUI to remove unwanted/unused iSCSI targets.

75008 #%d: ql_process_error: OB_TCP_IOCB_RSP_W returned DdbInx 0x%x pTpb %p

iSCSI Error A TCP retry for a frame failed on the connection ddbIndex. Tpb contains the frame memory address.

86347 #%d: QLDisable: Restart RISC iSCSI Info Restart iSCSI processor (RISC).

86349 #%d: QLEnable: Restart RISC to update EEPROM

iSCSI Info EEPROM updated, restart iSCSI processor (RISC).




B–Log Messages

ISR654601-00 E B-17

86874 #%d: QLIsrDecodeMailbox: Link up iSCSI Info Link up reported by iSCSI processor for GE1 or GE 2.

87346 #%d: QLGetFwStateCallback: link 100Mb FDX iSCSI Info iSCSI controller reported a link speed/configuration of 100Mb full-duplex (FDX).

87348 #%d: QLGetFwStateCallback: link 1000Mb FDX

iSCSI Info iSCSI controller reported a link speed/configuration of 1000Mb FDX.

87350 #%d: QLGetFwStateCallback: Invalid link speed 0x%x

iSCSI Info iSCSI controller reported an invalid link speed.

102419 #%d: qlutm_init: Diagnostic failed, port 1 invalid SRAM

FC Fatal FC1 processor SRAM test failed.

102420 #%d: qlutm_init: Diagnostic failed, port 1 POST failed

FC Fatal FC1 processor power-on self-test (POST) failed.

102421 #%d: qlutm_init: Diagnostic failed, port 2 invalid SRAM

FC Fatal FC2 processor SRAM test failed.

102422 #%d: qlutm_init: Diagnostic failed, port 2 POST failed

FC Fatal FC2 processor POST failed.

102423 #%d: qlutm_init: Failed to return diagnostic result to Bridge

FC Fatal Fibre Channel processor failed to return diagnostic results.

102656 #%d: QLInitializeAdapter: Reset ISP failed

FC Fatal Fibre Channel processor failed reset.

102657 #%d: QLInitializeAdapter: Load RISC code failed

FC Fatal Fibre Channel processor firmware load failed.




B–Log Messages

B-18 ISR654601-00 E

102658 #%d: QLInitializeAdapter: Load ISP2322 receive sequencer code failed

FC Fatal Fibre Channel processor receive sequencer code load failed.

102659 #%d: QLInitializeAdapter: Load ISP2322 transmit sequencer code failed

FC Fatal Fibre Channel processor transmit sequencer code load failed.

102662 #%d: QLInitializeAdapter: Verify Checksum command failed (%x)

FC Fatal Fibre Channel processor firmware checksum failed.

102680 #%d: QLInitializeFW: FAILED FC Fatal Fibre Channel processor firmware initialization failed.

102688 #%d: QLInterruptServiceRoutine: Risc pause %x with parity error hccr %x, Disable adapter

FC Fatal Fibre Channel processor paused due to internal par-ity error.

102689 #%d: QLInterruptServiceRoutine: Invalid interrupt status: %x

FC Fatal Fibre Channel processor returned an invalid interrupt status.

102716 #%d: QLIsrEventHandler: System error event (%x), MB1=%x, MB2=%x, MB3=%x, MB4=%x, MB5=%x, MB6=%x, MB7=%x

FC Fatal Fibre Channel processor system error.

102746 #%d: QLProcessResponseQueue: Invalid handle %x, type %x

FC Fatal Response queue entry contains an invalid handle.

102752 #%d: QLTimer: Ext Ram parity error exceed limit cnt 0x%x, limit 0x%x, Disabled adapter

FC Fatal Fibre Channel processor external SRAM parity error count exceeded limit; Fibre Channel port disabled.

102755 #%d: QLTimer: Heartbeat failed FC Fatal Fibre Channel processor heartbeat failed.

102800 #%d: QLRestartRisc: restart RISC FC Fatal Fibre Channel processor being restarted.




B–Log Messages

ISR654601-00 E B-19

106583 #%d: QLUtmReceiveIo: Path invalid/FW No resource count %x

FC Error Fibre Channel processor received a SCSI command for an unknown target path or has run out of resources to execute additional commands.

106589 #%d: QLIoctlEnable: Adapter disabled FC Error Fibre Channel processor was disabled by an IOCTL request to the driver.

106590 #%d: QLIoctlEnable: Initialize FW error FC Error Fibre Channel processor firmware failed initialization. The request to initialize was received by the driver in an IOCTL request.

106592 #%d: QLIoctlRunDiag: Diagnostic loopback command failed %x% %x %x

FC Error Fibre Channel processor failed the external loopback test.

106593 #%d: QLIoctlDisable: Re-initialize adapter failed

FC Error Fibre Channel processor failed to re-initialize in response to an IOCTL disable request.

106803 #%d: QLIsrEventHandler: Link down (%x) FC Error Fibre Channel processor reported a link down condi-tion.

106813 #%d: QLIsrEventHandler: Unexpected async event (%x), MB1=%x, MB2=%x, MB3=%x, MB4=%x, MB5=%x, MB6=%x, MB7=%x

FC Error Fibre Channel processor reported an unexpected asynchronous event. The mailbox registers provide status, event code, and data related to the event.

106847 #%d: QLProcessResponseQueue: Invalid EntryStatus %x, type %x

FC Error Fibre Channel controller reported an invalid Entry Status %x, type %x.

106851 #%d: QLTimer: Heartbeat failed FC Error Fibre Channel controller failed to provide a heartbeat.




B–Log Messages

B-20 ISR654601-00 E

106853 #%d: QLTimer: Link error count (0x%x) exceeded, link down

FC Error Driver has determined that the Fibre Channel link is unreliable and unusable due to the number of errors encountered. The link has been taken down.

106912 #%d: QLReserveLoopId: out of loop Ids FC Error Fibre Channel processor was unable to obtain the number of loop IDs required. This failure occurs only when the Fibre Channel processor is running multi-ID firmware.

106928 #%d: QLMarkDeviceOffline: Device Id: %x marked offline, cLinkDownTimeout = %x, cPortDownRetryCount=%x

FC Error Driver was unable to re-establish connection to the target within the timeout and retry counts, and is therefore marking it offline.

106948 #%d: QLSnsGetAllNext: Name server login FAILED %x

FC Error Fibre Channel processor is unable to log into the Fibre Channel fabric name server.

107029 #%d: QLUpdateDeviceData: out of slots in host database

FC Error Driver’s host (initiator) database is full.

107030 #%d: QLUpdateDeviceData: out of slots in target database

FC Error Driver’s target database is full.

107041 #%d: QLUpdateDeviceDatabase 0x%x: GET_ID failed %x

FC Error Driver’s host (initiator) database is full. Maximum host database is 64.

107056 #%d: QLUpdateDeviceDatabase 0x%x: out of slots in host database

FC Error Drivers host (initiator) database is full.

107078 #%d: QLUpdatePort 0x%x: out of slots in host database

FC Error Driver was unable to re-establish connection to the target within the timeout and retry counts, and is therefore marking it offline.




B–Log Messages

ISR654601-00 E B-21

107984 #%d: QLWriteFlashDword: Write fails at addr 0x%x data 0x%x

FC Error Fibre Channel controller failed a Flash write (address x data x).

108032 #%d: QLGetVpDatabase: MBOX_CMD_GET_VP_DATABASE for VP %d fatal error

FC Error Fibre Channel controller failed the Get VP Database command (for virtual port %d).

108033 #%d: QLGetVpDatabase: MBOX_CMD_GET_VP_DATABASE for VP %d failed %x

FC Error Fibre Channel controller failed the Get VP Database command (for virtual port %d) with status x.

108049 #%d: QLVerifyMenloFw: EXECUTE_COMMAND_IOCB failed MB0 %x MB1 %x

FC Error Fibre Channel controller reported failure status for an Execute IOCB (input/output control block) command.

108050 #%d: QLVerifyMenloFw: EXECUTE_COMMAND_IOCB fatal error

FC Error Fibre Channel controller reported a fatal error while processing an Execute IOCB command.

108064 #%d: QLGetFwState: Get Firmware State failed 0-3 %x %x %x %x

FC Error Fibre Channel controller reported failure status for a Get Firmware State command.

118882 #%d: QLIoctlDisable: Reset adapter FC Info Request to reset the Fibre Channel processor (adapter) received from ioctl interface.

119088 #%d: QLIsrEventHandler: LIP occurred (%x): mailbox1 = %x

FC Info Fibre Channel loop initialization process (LIP) occurred. The LIP type is reported, as is the contents of the Fibre Channel processor’s mailbox 1 register.

119089 #%d: QLIsrEventHandler: LIP reset occurred (%x): mailbox1 = %x

FC Info Fibre Channel LIP reset occurred. The LIP reset type is reported, as is the contents of the Fibre Channel processor’s mailbox 1 register.




B–Log Messages

B-22 ISR654601-00 E

119090 #%d: QLIsrEventHandler: Link up (%x) mailbox1 = %x

FC Info Fibre Channel link up occurred. Event status is reported, as is the contents of the Fibre Channel pro-cessor’s mailbox 1 register.

119092 #%d: QLIsrEventHandler: Link mode up (%x): RunTimeMode=%x

FC Info Fibre Channel link up occurred. Event status is reported, as is the RunTimeMode (0 = loop, 1 = point-to-point).

119093 #%d: QLIsrEventHandler: RSCN update (%x) rscnInfo: %x

FC Info An RSCN was received. Event status is reported, as is the RSCN information.

119097 #%d: QLIsrEventHandler: Port update (%x) mb1-3 %x %x %x

FC Info Fibre Channel port update. Event status is reported, as is the contents of the Fibre Channel processor’s mailbox 1, 2, and 3 registers.

119144 #%d: QLTimer: VP %d discover a reject device PID %02x%02x%02x

FC Info A virtual port logged into a device, but the device rejects the login.

120278 #%d: QLFlashGetNvram: Invalid Serial Link Control 0x%x for port %d

FC Info Update NVRAM for the invalid Serial Link Control for mezzanine platform.

120373 #%d: QLIsrEventHandler: DCBX Completed (%x)

FC Info For FCoE protocol, the Data Center Bridging Exchange protocol completes.

120374 #%d: QLIsrEventHandler: IDC Completion (%x) %x, %x, %x, %x, %x, %x, %x

FC Info For FCoE protocol, the Inter-Driver Communication completes.

120375 #%d: QLIsrEventHandler: IDC Notification (%x), %x, %x, %x, %x, %x, %x, %x

FC Info For FCoE protocol, the IDC notification comes from another driver.

120376 #%d: QLIsrEventHandler: IDC Time Extended (%x), %x, %x, %x, %x, %x, %x, %x

FC Info For FCoE protocol, the IDC time extended notifica-tion receives.




B–Log Messages

ISR654601-00 E B-23

120377 #%d: QLIsrEventHandler: DCBX Started (%x) FC Info For FCoE protocol, the DCBX protocol has started.

120378 #%d: QLIsrEventHandler: FCF Config Error (%x), MB1=%x

FC Info For FCoE protocol, the FCF configuration error occurred.

120379 #%d: QLIsrEventHandler: DCBX Parameter Changed (%x)

FC Info For FCoE protocol, the DCBX parameters are changed.

139265 QBRPC_Initialize: Entered User Error RPC (remote procedure call) server initialization entry point.

139266 QBRPC_Initialize:GetBridge Mem Allocation error

User Error Get System API memory allocation failed.

139267 QBRPC_Initialize:GetBridgeAdv Mem Allocation error

User Error Get System Advanced API memory allocation failed.

139268 QBRPC_Initialize:GetMgmt Mem Allocation error

User Error Get Management API memory allocation failed.

139269 QBRPC_Initialize:GetIscsi Mem Allocation error

User Error Get iSCSI API memory allocation failed.

139270 QBRPC_Initialize:GetIscsiAdv Mem Allocation error

User Error Get iSCSI advanced API memory allocation failed.

139271 QBRPC_Initialize:GetIsns Mem Allocation error

User Error Get iSNS API memory allocation failed.

139272 QBRPC_Initialize:GetFcIntfc Mem Allocation error

User Error Get Fibre Channel Interface API memory allocation failed.




B–Log Messages

B-24 ISR654601-00 E

139273 QBRPC_Initialize:GetFcAdv Mem Allocation error

User Error Get Fibre Channel Advanced API memory allocation failed.

139280 QBRPC_Initialize:GetFcSfp Mem Allocation error

User Error Failed memory allocation for Get Fibre Channel SFP API.

139281 QBRPC_Initialize:GetLog Mem Allocation error

User Error Failed memory allocation for Get Log API.

139282 QBRPC_Initialize:GetStats Mem Allocation error

User Error Failed memory allocation for Get Statistics API.

139283 QBRPC_Initialize:InitListMem Allocation error

User Error Failed memory allocation for Get Initiator List API.

139284 QBRPC_Initialize:TargetList Mem Allocation error

User Error Failed memory allocation for Get Target List API.

139285 QBRPC_Initialize:LunList MemAllocation error

User Error Failed memory allocation for Get LUN List API.

139286 QBRPC_Initialize:PresTarget Mem Allocation error

User Error Failed memory allocation for Get Presented Targets List API.

139287 QBRPC_Initialize:LunMask Mem Allocation error

User Error Failed memory allocation for Get LUN Mask API.

139288 QBRPC_Initialize:Init Mem Allocation error

User Error Failed memory allocation for Initiator API.

139289 QBRPC_Initialize:TgtDevice Mem Allocation error

User Error Failed memory allocation for Target Device API.




B–Log Messages

ISR654601-00 E B-25

139296 QBRPC_Initialize:FcTgt Mem Allocation error

User Error Failed memory allocation for Fibre Channel Target API.

139297 QBRPC_Initialize:BridgeStatus Mem Allocation error

User Error Failed memory allocation for System Status API.

139298 QBRPC_Initialize:Diag Mem Allocation error

User Error Failed memory allocation for Diagnostic API.

139299 QBRPC_Initialize:DiagLog Mem Allocation error

User Error Failed memory allocation for Diagnostic Log API.

139300 QBRPC_Initialize:FruImage Mem Allocation error

User Error Failed memory allocation for FRU Image API.

139301 QBRPC_Initialize:OemMfg Mem Allocation error

User Error Failed memory allocation for OEM Manufacturing API.

139302 QBRPC_Initialize:Status Mem Allocation error

User Error Failed memory allocation for Status API.

139303 QBRPC_Initialize:TcpIpStats Mem Allocation error

User Error Failed memory allocation for TCP/IP Statistics API.

139304 QBRPC_Initialize:NtpStats Mem Allocation error

User Error Failed memory allocation for NTP Status API.

139305 QBRPC_Initialize:LunList MemAlloc error User Error Failed memory allocation for LUN List API.

139315 QBRPC_FreeResources:Entered User Error RPC free resources entry point.

139553 checkDuplicateIp: Detected Error %08x %08x%04x

User Error Detected duplicate IP address for management port.




B–Log Messages

B-26 ISR654601-00 E

139930 FcipRoute#%d Failed with Memory Allocation Error

App Error FCIP route add/mod failed because of lack of mem-ory.

139931 FcipRoute#%d Failed with Invalid Arg Error App Error FCIP route add/mod failed because the arguments supplied were incorrect.

139932 FcipRoute#%d Failed with Unknown Device Error

App Error FCIP route add/mod failed because of incorrect con-figuration

139933 FcipRoute#%d Failed with Kernel Error App Error FCIP route add/mod failed because of configuration error

139934 FcipRoute#%d Failed with Network Configuration Error

App Error FCIP route add/mod failed because the Ethernet net-work

139935 FcipRoute#%d Failed with Persistence Read Failure

App Error FCIP route add/mod failed because of an error in reading the saved configuration from persistence

139936 FcipRoute#%d Failed with Persistence Write Failure

App Error FCIP route add/mod failed because of an error in writing the route configuration to persistence

139937 FcipRoute#%d Failed with IP Address Reuse Error

App Error FCIP route add/mod failed because an IP address supplied is already under use.

139938 FcipRoute#%d Add Failed because relevant FCIP Licence not available

App Error FCIP route add/mod failed because FCIP license is not present.

151842 FW Upgrade performed: new version is: %d.%d.%d.%d

User Info A firmware upgrade was performed; the new version is: d.d.d.d.

151843 REBOOT/SHUTDOWN Command from user. Code=%d

User Info User issued a REBOOT or SHUTDOWN command.




B–Log Messages

ISR654601-00 E B-27

151889 #%d: qapisetfcinterfaceparams_1_svc: FC port configuration changed

User Info Fibre Channel port configuration has changed.

151890 #%d: qapisetiscsiinterfaceparams_1_svc: iSCSI port configuration changed

User Info iSCSI port configuration has changed.

151891 #%d: qapisetisns_1_svc:iSNS configuration changed

User Info iSNS configuration has changed.

151892 qapisetntpparams_1_svc: NTP configuration changed

User Info NTP configuration has changed.

151893 #%d: qapisetvlanparams_1_svc: VLAN configuration changed

User Info VLAN configuration has changed.

151894 qapisetlunmask_1_svc: Lunmask added for LUN %d

User Info A LUN mask was added for LUN %d.

151895 qapisetlunmask_1_svc: Lunmask removed for LUN %d

User Info LUN mask was removed for LUN %d.

151896 qapisetmgmintfcparams_1_svc:Management port configuration changed

User Info Management port configuration has changed.

151897 qapisetbridgebasicinfo_1_svc:Bridge configuration changed

User Info Router configuration has changed.

151908 GE%d: Port status changed by user to ENABLED.

User Info GE port %d was enabled user.

151909 GE%d: Port status changed by user to DISABLED.

User Info GE port %d was disabled by user.




B–Log Messages

B-28 ISR654601-00 E

151910 FC%d: Port status changed by user to ENABLED.

User Info Fibre Channel port %d was enabled by user.

151911 FC%d: Port status changed by user to DISABLED.

User Info Fibre Channel port %d was disabled by user.

151912 qapimaptargetdevice_1_svc: Target WWPN: %.2x%.2x%.2x%.2x%.2x%.2x%.2x%.2x mapped to iSCSI portal %d.

User Info Target at WWPN: xx.xx.xx.xx.xx.xx.xx.xx has been mapped to iSCSI portal %d.

151913 qapimaptargetdevice_1_svc: Target WWPN: %.2x%.2x%.2x%.2x%.2x%.2x%.2x%.2x unmapped from iSCSI portal %d.

User Info Target at WWPN: xx.xx.xx.xx.xx.xx.xx.xx has been unmapped from iSCSI portal %d

152069 FcipRoute#%d Added App Info FCIP route #n has been successfully added.

152070 FcipRoute#%d Modified App Info FCIP route #n has been successfully modified.

152071 FcipRoute#%d Removed App Info FCIP route #n has been successfully removed.

152082 qapiaddmodifyinitiator_1_svc : Initiator Configuration Changed

User Info An Initiators configuration has changed.

152083 qapiremoveinitiator_1_svc : Initiator Removed

User Info An Initiator has been removed.

152096 qapisetmigrfctargets_1_svc: Configuration Changed for migration target

User Info A set array was done on one of the arrays.

152099 LogMigration: Error in Writting log file User Info Encountered an error while updating the migration log entry. Some migration log entries might be miss-ing.




B–Log Messages

ISR654601-00 E B-29

152100 qapiaddgroup_1_svc: Added Group with id %d User Info Group with ID specified in the log was added.

152101 qapiremovegroup_1_svc: Removed Group with id %d

User Info Group with ID specified in the log was removed.

152102 qapiupdategroup_1_svc: Updated Group with id %d

User Info Group with ID specified in the log was updated.

152103 qapisetserialjobs_1_svc: Serial Time %lu User Info Serial schedule jobs scheduled to start at time speci-fied in the log.

152104 qapireadjustpriority_1_svc: Readjust Priority Failed on line %d with error %d

User Info Readjust priority command completed with an error. Error code 2 indicates no scheduled jobs were found. Error code 16 indicates a job with priority 1 config-ured.

152105 qapireadjustpriority_1_svc: Readjust Priority Done

User Info Completed readjusting the serial schedule priority of migration jobs.

152106 qapiupdatemigration_1_svc: Update Migration returned with error %d

User Info An update migration action [Start/Stop/Pause/Resume] has failed.

152107 RemoveMigration:%d with Job Id %d and error = %d

User Info Failed to remove a migration job with ID specified in the log.

152108 ValidateSerialSchedule: Previous time %ld New time %ld

User Info Reset the serial schedule delayed time to invalid if the last serial schedule job was removed.

152109 addMigration: Creating migration Job Failed with error %d

User Info Failed to create a migration job.




B–Log Messages

B-30 ISR654601-00 E

152129 sysTempMon: Left PCM Installed User Info Left power and cooling module (PCM) is or has been installed.

152130 sysTempMon: Left PCM Un-installed User Info Left PCM is or has been uninstalled.

152131 sysTempMon: Right PCM Installed User Info Right PCM is or has been installed.

152132 sysTempMon: Right PCM Un-installed User Info Right PCM is or has been uninstalled.

152133 sysTempMon: Power for Left PCM Plugged-in User Info Left PCM is connected AC power.

152134 sysTempMon: Power for Left PCM Un-plugged User Info Left PCM is not connected to AC power (unplugged).

152135 sysTempMon: Power for Right PCM Plugged-in User Info Right PCM is connected AC power.

152136 sysTempMon: Power for Right PCM Un-plugged User Info Right PCM is not connected to AC power (unplugged).

152137 sysTempMon: Slot 1 (R1) PCM Fan%d faulty User Info Left PCM (#1) is reporting a faulty fan.

152138 sysTempMon: Slot 2 (R2) PCM Fan%d faulty User Info Left PCM (#1) is reporting a healthy fan.

152139 sysTempMon: Slot 1 (R1) PCM Fan%d healthy User Info Right PCM (#2) is reporting a faulty fan.

152140 sysTempMon: Slot 2 (R2) PCM Fan%d healthy User Info Right PCM (#2) is reporting a healthy fan.

152141 sysTempMon: Over Temperature Front: %dC Rear: %dC CPU1: %dC CPU2: %dC

User Info Router has detected an over temperature, Front: %dC Rear: %dC CPU1: %dC CPU2: %dC

152142 sysTempMon: Setting the fan speed to high User Info Fan(s) speed has been set to high.

152143 sysTempMon: Setting the fan speed to normal

User Info Fan(s) speed has been set to normal.




B–Log Messages

ISR654601-00 E B-31

152144 sysTempMon: Temperature back to safe value. Front: %dC Rear: %dC CPU1: %dC CPU2: %dC

User Info Router temperature has returned to normal operating range, Front: %dC Rear: %dC CPU1: %dC CPU2: %dC

152145 sysTempMon: Critical Temperature, Shutting Down Front: %dC Rear: %dC CPU1: %dC CPU2: %dC

User Info Router has reached a critical temperature ad is shut-ting down, Front: %dC Rear: %dC CPU1: %dC CPU2: %dC

172040 FcipRoute#%d: Cleaning FCIP Instance FCIP Error This is an informative message not an error. This indicates an FCIP was removed or modified.

172231 FcipRoute#%d: Did not get the keepalive msg form remote peer

FCIP Error FCIP route #n has not been able to communicate with the remote peer for 10 sec.

172238 FcipRoute#%d: Synchronization Error on Receive

FCIP Error FCIP route #n local node is out of sync with the remote peer.

172239 FcipRoute#%d: Decompression Error on Receive

FCIP Error FCIP route #n detected an error in de-compression

172240 FcipRoute#%d: De-encapsulation Error on Receive

FCIP Error FCIP route #n Local Node is out of sync with the remote peer.

172245 FcipRoute#%d: Transmit Failure FCIP Error FCIP route #n not able to transmit data.

172246 FcipRoute#%d: Remote Peer Disconnected FCIP Error FCIP route #n remote peer closed connection.

172247 FcipRoute#%d: Failed to send FC Up/Down FCIP Error Not able to bring the Fibre Channel port up or down.

172249 FcipRoute#%d: FCIP Link Down FCIP Error FCIP link is down for FCIP route#n.

172250 FcipRoute#%d: TCP Link Down FCIP Error TCP link for FCIP route #n has been established.




B–Log Messages

B-32 ISR654601-00 E

172253 FcipRoute#%d: Remote Peer IP Address Validation Failed. Expected IP Address: %d.%d.%d.%d, Actual IP Address: %d.%d.%d.%d

FCIP Error FCIP route #n: Received connection from unauthor-ized remote peer.

172272 FcipRoute#%d: Tcp Client's connect attempt failed

FCIP Error FCIP route #n is not able to establish the TCP con-nection with remote peer.

172273 FcipRoute#%d: Tcp Server's Listen attempt failed

FCIP Error FCIP route #n is not able to establish the TCP con-nection with remote peer.

172300 FcipRoute#%d: tcpi_total_retrans %d, tcpi_reordering %d, tcpi_probes %d

FCIP Error Displays FCIP route#n's WAN characteristics, includ-ing TCP total retransmission for entire connection (tcpi_total_retrans), packet reordering metric (tcpi_reordering), and unanswered zero window probe (tcpi_probes).

172301 FcipRoute#%d: Did not get the keepalive msg form remote peer last %lu, curr %lu

FCIP Error The FCIP route#n has not been able to communicate with its remote peer for ten seconds resulting in a link drop due to a keepalive timeout.

172302 FcipRoute#%d: TCP Link Down, TCP Stats: SACKed=%d TCP Total ReTransmitted=%d

FCIP Error The TCP link for FCIP route#n has disconnected. The TCP statistics for the connection include total SACKs (selective acknowledgements) and total retransmission for the connection.




B–Log Messages

ISR654601-00 E B-33

172303 FcipRoute#%d: TCP Link Down, MAC Stats: Tx Dropped Count=%ld Rx Dropped Count=%ld Tx Pause Count=%ld Rx Pause Count=%ld

FCIP Error The TCP link for FCIP route#n has disconnected. The MAC or Ethernet statistics include total packet dropped during transmit (TxDropped), total packet dropped during receive (RxDropped), total Ethernet pause frames transmitted (TxPause), and total Ether-net pause frames received (RxPause).

172304 FcipRoute#%d: Tcp Retranmissions in last 10 Sec %d, OutStanding Completions %d FC Frames

FCIP Error The total number of TCP retransmissions that hap-pened in the last ten seconds before the link was brought down due to a keepalive timeout. It also dis-plays the total number of outstanding transmissions that were pending to be transmitted through the GbE port.

172322 FcipRoute#%d: FC link on the remote peer went down

FCIP Error The FCIP route#n went down because the Fibre Channel port on the remote peer went down.

184515 FcipRoute#%d: TCP Link Up FCIP Info TCP link for FCIP route #n has been established.

184536 FcipRoute#%d: FCIP Link Up FCIP Info FCIP link is up for FCIP route #n.

184542 FcipRoute#%d: VLAN Info Unavailable FCIP Error FCIP route #n: Incorrect VLAN configuration.

205571 QL3xxx:%s: Auto Negotiation error detected

NIC Error Ethernet port was not able to negotiate the config-ured speed.

205572 QL3xxx:eth%d: Unsupported speed portConfig 0x%x

NIC Error Ethernet port speed is not supported.

206080 QL3xxx:ql3xxx_probe: cannot allocate ethernet device %s

NIC Error Ethernet device could not be configured.




B–Log Messages

B-34 ISR654601-00 E

206089 QL3xxx:ql3xxx_probe: cannot register network device %s

NIC Error The Ethernet port was not able to register as a net-work device resulting in a port initialization error for the specified network device.

206114 QL3xxx:eth%d: TCP/IP checksum error - TotalChecksumErrorCount = %lu

N IC Error The total number of TCP checksum errors detected on the Ethernet link belonging to the eth#%d port.

217856 QL3xxx:%s: PHY Downshift occurred NIC Info Ethernet port is operating at 100mbps speed.

217857 QL3xxx:%s: Link Up NIC Info Ethernet link is up.

217858 QL3xxx:%s: Link Down NIC Info Ethernet link is down.

218389 QL3xxx:%s Adapter Down NIC Info Ethernet port is down.

218401 QL3xxx:%s Adapter Up NIC Info Ethernet port is up.

233473 "memory monitor: Detected Uncorrectable Ecc %08lx system is rebooting in 5 secs\n"

System Fatal Uncorrectable memory error detected at address pro-vided in log message.

233474 "Failed to register interrupt handler!\n" System Fatal Attempt to register the interrupt handler failed.

233475 "%s class_simple_create failed\n" System Fatal Failed class_simple_create system call from memory monitor initialization routine.

237572 "Failed to kill sys killer %d\n" System Error Failed to kill system task.

237573 Temperature over high threshold %d System Error Router temperature has exceeded the high tempera-ture threshold.

249862 Temperature is back to normal range %d System Info Router temperature has returned to the normal oper-ating range.




ISR654601-00 E Glossary-1

Glossary

activity LED

A port LED that indicates when frames are entering or leaving the port.

adapter

The board that interfaces between the host system and the target devices. Adapter is synonymous with host bus adapter (HBA), host adapter, and adapter board.

adapter port

A port on the adapter board.

adapter port beacon

An LED on the adapter. Flashing it enables you to locate the adapter.

application specific integrated circuit

See ASIC.

arbitrated loop

A circular (ring) topology (versus point-to-point) where two or more ports can be interconnected, but only two ports can communicate at a time. All communi-cation passes through all ports connected to the loop.

ASIC

Application specific integrated circuit. A microchip designed for special applica-tions such as Fibre Channel.

challenge-handshake authentication protocol

See CHAP.

CHAP

Challenge-handshake authentication protocol is used for remote logon, usually between a client and server or a Web browser and Web server. A challenge/response is a security mecha-nism for verifying the identity of a person or process without revealing a secret password that is shared by the two entities. Also referred to as a” three-way handshake.”

command line interface

See CLI.

CLI

Program interface driven by entering commands and parameters.

CRC

Cyclic redundancy check. A type of check value designed to catch most transmission errors.

cyclic redundancy check

See CRC.


User’s Guide

Glossary-2 ISR654601-00 E

device

A target, typically a disk drive. Hardware such as a disk drive, tape drive, printer, or keyboard that is installed in or connected to a system. In Fibre Channel, a target device.

driver

The software that interfaces between the file system and a physical data storage device or network media.

electrically erasable programmable read-only memory

See EEPROM.

EEPROM

Electrically erasable programmable read-only memory. Memory that can be erased (entirely, not selectively) using higher electrical voltages.

Enhanced Ethernet

Also called data center Ethernet or converged enhanced Ethernet. Refers to new enhancements to the existing Ethernet standard that eliminate Ethernet’s inherently lossy nature and make 10Gb Ethernet a viable storage networking transport.

fabric

A fabric consists of cross-connected Fibre Channel devices and switches.

fabric switch

Also, switched fabric. A fabric switch connects multiple devices from indepen-dent Fibre Channel-arbitrated loops (FC-ALs) and point-to-point topologies into a fabric using Fibre Channel switches.

failover path

Software feature that ensures data avail-ability and system reliability by assigning alternate path and automatic adapter failover for device resources. This feature is available only in Windows 2000/Windows Server 2003/Windows Vista, Novell NetWare, and Red Hat/SUSE Linux. (Windows XP and Windows Server 2008 do not support failover.)

FC

See Fibre Channel.

FC-IP mode

Data transportation mode in which the iSR6200 transports Fibre Channel frames over a TCP/IP connection using the FCIP protocol to connect two iSR6200 routers. In FC-IP mode, a port pair (one Fibre Channel port and an IP port on the same router) on local iSR6200 and another port pair on a remote router form a FCIP route.

FCIP

Fibre Channel over IP. Protocol that enables transmission of Fibre Channel information by tunneling data on a SAN over IP networks. An alternative to iSCSI. Also known as Fibre Channel tunneling.

FCoE

Fibre Channel over Ethernet. A new technology defined by the T11 standards body that allows traditional Fibre Channel storage networking traffic to travel over an Ethernet link by encapsulating Fibre Channel frames inside Layer 2 Ethernet frames. For more information, visit www.fcoe.com.

Fibre Channel

A high-speed serial interface technology that supports other higher layer protocols such as SCSI and IP.

http://www.fcoe.com

http://www.fcoe.com

http://www.fcoe.com



User’s Guide

Fibre Channel over Ethernet

See FCoE.

Fibre Channel over IP

See FCIP.

field replaceable unit

See FRU.

Flash

Non-volatile memory where the boot code is saved. At times, flash and boot code are used interchangeably.

Flash BIOS

A QLA2xxx adapter's flash programmable read-only memory (PROM) contains the code that allows booting from the adapter at startup.

frame

Data unit consisting of a start-of-frame (SOF) delimiter, header, data payload, CRC, and an end-of-frame (EOF) delim-iter.

FRU

Field replaceable unit. Component that can be replaced in the field upon failure.

HBA

Host bus adapter. See adapter.

heartbeat LED

A chassis LED that indicates the router status.

hot replaceable

Also known as “hot swappable,” this means you can add new devices or remove existing ones when the system is running.

IANA

Internet Assigned Numbers Authority (IANA) is responsible for the global coordi-nation of the DNS Root, IP addressing, and other Internet protocol resources.

initiator

System component, such as a network interface card, that originates an I/O operation.

input/output control

See IOCTL.

input/output control block

See IOCB.

Internet Assigned Numbers Authority

See IANA.

Internet simple name service

See iSNS.

Internet small computer system interface

See iSCSI.

IOCB

Input/output control block.

IOCTL

Input/output control. A system call in Unix/Linux systems that allows an applica-tion to control or communicate with a device driver outside usual read/write operations.

IP

Internet protocol. A method by which data is sent from one computer to another over the Internet. IP specifies the format of packets, also called datagrams, and the addressing scheme.


User’s Guide


IP address

Internet protocol address. The numeric address of a computer that is in the format used on the internet.

iSCSI

Internet small computer system interface. Protocol that encapsulates data into IP packets to send over Ethernet connec-tions.

iSNS

Internet simple name service (iSNS) is used for discovery and management of IP-based SANs.

latency

A measure of how fast a transaction travels through the router.

LIP

Loop initialization process. The initializa-tion process in an arbitrated loop that occurs when the loop is powered up or a new device is added. One function of a LIP is to assign addresses. All data transmis-sion on the loop is suspended during a LIP.

load balancing

A software feature that improves system performance by balancing device access between multiple ports for maximum resource efficiency.

logical unit number

See LUN.

loop initialization process

See LIP.

loopback

Diagnostic tool that routes transmit data through a loopback connector back to the same adapter.

LUN

Logical unit number, a subdivision of a SCSI target. It is the small integer handle that differentiates an individual disk drive or partition (volume) within a common SCSI target device such as a disk array.

Technically, a LUN can be a single physical disk drive, multiple physical disk drives, or a portion (volume) of a single physical disk drive. However, LUNs are typically not entire disk drives but rather virtual partitions (volumes) of a RAID set.

Using LUNs, the Fibre Channel host can address multiple peripheral devices that may share a common controller.

MAC address

Media access control address. A unique hardware device identifier used in IP address assignment.

maintenance button

Multifunction momentary switch on the front panel of the router.

management information base

See MIB.

management workstation

PC workstation used to manage routers remotely by connecting to the routers using the SANsurfer Router Manager or CLI commands.

media access control address

See MAC address.

MD5

Message-digest algorithm 5. A widely used, partially insecure cryptographic hash function with a 128-bit hash value. An MD5 hash is typically expressed as a 32 digit hexadecimal number.



User’s Guide

media

Physical-layer information carriers. Fibre Channel supports several different physical media: copper, multimode optical, and single-mode optical. All Fibre Channel protocols are supported on all media.

MIB

Management information base. A set of guidelines and definitions for SNMP functions.

mid-plane

Located inside the iSR6200 chassis between the blades and their corre-sponding PCMs, the mid-plane connects the removable power supply and the iSR6200 blades.

network time protocol

See NTP.

non-volatile random access memory

See NVRAM.

NTP

Network time protocol is used for distrib-uting the Coordinated Universal Time (UTC) by means of synchronizing the clocks of computer systems over packet-switched, variable-latency data networks.

NVRAM

Non-volatile random access memory. A type of memory that retains data even when power is removed. Holds configura-tion settings. You can configure NVRAM settings manually or restore them from a file.

path

A path to a device is a combination of a adapter port instance and a target port as distinct from internal paths in the fabric network. A fabric network appears to the operating system as an opaque network between the adapter (initiator) and the target.

Because a path is a combination of an adapter and a target port, it is distinct from another path if it is accessed through a different adapter and/or it is accessing a different target port. Consequently, when switching from one path to another, the driver might be selecting a different adapter (initiator), a different target port, or both.

This is important to the driver when selecting the proper method of failover notification. It can make a difference to the target device, which might have to take different actions when receiving retries of the request from another initiator or on a different port.

PCM

Power and cooling module. A device that consists of one power supply and three fans.

point-to-point

Also FC-P2P. Two Fibre Channel nodes directly connected (not in a loop).

port

Access points in a device where a link attaches. There are four types of ports, as follows:

N_Port is a Fibre Channel port that supports point-to-point topology.

NL_Port is a Fibre Channel port that supports loop topology.

FL_Port is a port in a fabric where an N_Port can attach.


User’s Guide


FL_Port is a port in a fabric where an NL_Port can attach.

port instance

The number of the port in the system. Each adapter may have one or multiple ports, identified with regard to the adapter as port 0, port 1 and so forth. to avoid confusion when dealing with a system containing numerous ports, each port is assigned a port instance number when the system boots up. So Port 0 on an adapter might have a port instance number of 8, for example, if it is the eighth port discovered by the system.

POST

Power-on self test. Diagnostics that the router performs at start-up.

power and cooling module

See PCM.

power-on self test

See POST.

reduced instruction set computer

See RISC.

registered state change notification

See RSCN.

remote procedure call

See RPC.

RISC

Reduced instruction set computer. A computer microprocessor that performs fewer types of computer instructions, thereby operating at higher speeds.

RPC

Remote procedure call. A protocol used by a program to request a service from a program located in another computer in a network. RPC uses the client/server model.

RSA

In cryptography, RSA (which stands for Rivest, Shamir, and Adleman who first publicly described it) is an algorithm for public-key cryptography. RSA is the first algorithm suitable for both signing and encryption. It can be used for encrypting messages and making digital signatures.

RSCN

Registered state change notification (RSCN) is a Fibre Channel fabric notifica-tion sent to all specified nodes when any major fabric changes occur. This notifica-tion allows nodes to immediately gain knowledge about the fabric and react accordingly.

router log

Log of messages describing events that occur on the intelligent storage router.

SAN

Storage area network. Multiple storage units (disk drives) and servers connected by networking topology.

SANsurfer Router Manager

Also know as SANsurfer iSCSI/FC Router Manager. A workstation-based router management tool that provides a graphical user interface (GUI) used to configure and monitor intelligent storage routers.



User’s Guide

SCSI

Small computer system interface. A high-speed interface used to connect devices, such as hard drives, CD drives, printers, and scanners, to a computer. The SCSI can connect many devices using a single controller. Each device is accessed by an individual identification number on the SCSI controller bus.

Secure SHell

See SSH.

SFP

Small form-factor pluggable. A transceiver device, smaller than a GigaBit Interface Converter, that plugs into the Fibre Channel port.

simple network management protocol

See SNMP.

small computer system interface

See SCSI.

small form-factor pluggable

See SFP.

SNMP

Simple network management protocol. SNMP is a networking protocol that enables you to monitor the router using third-party applications that use SNMP.

SSH

Secure SHell. Communications tool that provides secure and encrypted connec-tions to traditionally non-encrypted services.

storage area network

See SAN.

target

The storage-device endpoint of a SCSI session. Initiators request data from targets. Targets are typically disk-drives, tape-drives, or other media devices. Typically a SCSI peripheral device is the target but an adapter may, in some cases, be a target. A target can contain many LUNs.

A target is a device that responds to a requested by an initiator (the host system). Peripherals are targets, but for some commands (for example, a SCSI COPY command), the peripheral may act as an initiator.

Telnet

Telecommunication network. A network protocol used on the Internet or local area network (LAN) connections. Telnet provides access to a command line inter-face (CLI) on a remote machine.

virtual logical area network

See VLAN.

virtual port group

See VPG.

VLAN

Virtual logical area network (LAN). A group of hosts with a common set of require-ments that communicate as if they were attached to the same wire, regardless of their physical location. Although a VLAN has the same attributes as a physical LAN, it allows for end stations to be grouped together even if they are not located on the same LAN segment. VLANs enable network reconfiguration through software, instead of physically relocating devices.


User’s Guide


VPG

Virtual port group (or VPGROUP). Software component configured in the iSCSI router that is used to create virtual adapters on all Fibre Channel ports on a blade.

world wide name

See WWN.

world wide node name

See WWNN.

world wide port name

See WWPN.

world wide unique LUN name

See WWULN.

WWN

World wide name. A unique 64-bit address assigned to a device by the device manufacturer.

WWNN

World wide node name. An unique 64-bit address assigned to a device.

WWPN

World wide port name. An unique 64-bit address assigned to each port on a device. One WWNN may contain multiple WWPN addresses.

WWULN

World wide unique LUN name. WWULN identifiers for SCSI devices are read from page 83 and page 80 of your SCSI block device as based on the SCSI standard. SANsurfer looks for identifiers in the order of: page 83 type 3, page 83 type 2, page 83 type 1, page 80, and lastly page 83 type 0.

ISR654601-00 E Index-1

Index

Aaccount, guest 1-2activity LED, definition of Glossary-1adapter

heartbeat missed error B-15login message B-9definition of Glossary-1

adapter port, definition of Glossary-1adapter port beacon, definition of Glossary-1adding

FCIP route 2-13initiator to database 2-26iSCSI global mapping 2-31LUN to initiator 2-34remote mappings 2-45remote peers 2-48target LUN mapping 2-38

addressidentifier, FC port A-8IP of port A-6MAC, of port A-6mode, port A-5

admin authority 2-6admin command 2-7administrator

password, changing 2-41session, closing and opening 2-7session, requirements for 2-6

agentshutdown notification A-21software version number A-20startup notification A-21

agreements, license xivalias, setting for target 2-57

application specific integrated circuit, See ASIC

arbitrated loop, definition of Glossary-1ASIC

definition of Glossary-1traces, saving 2-54

audience for this guide xiauthentication traps, enabling A-2authentication, mutual

configuring CHAP (discovery session) 3-2configuring CHAP (normal session) 3-4

authority requirements 2-6

Bbeacon command 2-8beacons (LEDs), enabling 2-8bi-directional CHAP

discovery session, configuring for 3-2normal session, configuring for 3-4

bladecommands, list of 2-2iSNS parameters, setting 2-65prompt 2-9properties, setting 2-69properties, showing 2-115selecting for management 2-9statistics, showing 2-126updating with saved configuration data 1-5

blade command 2-9


User’s Guide

Index-2 ISR654601-00 E

Ccapturing debug dump data 2-53challenge handshake authentication protocol,

See CHAPCHAP

authentication error B-4configuration, displaying 2-78configuring 3-1definition of Glossary-1description of 3-1key error B-4router parameters, configuring 2-59

chassiscommands, list of 2-2information and status, showing 2-79prompt 2-9

clear command 2-10clearing router log entries 2-10CLI

definition of Glossary-1logging out of 2-30usage 1-1

closing administrator session 2-7command line completion 2-5command line interface, See CLIcommand reference 2-1command syntax 2-5commands

admin 2-7beacon 2-8blade 2-9clear 2-10date 2-11exit 2-12fciproute 2-13fru restore 1-6, 2-17fru save 2-17help 2-18history 2-24image 2-25initiator 2-26iscsi 2-28logout 2-30

commands (continued)lunigmap 2-31lunmask 2-34lunremap 2-38passwd (password) 2-41ping 2-42quit 2-43reboot 2-44remotemap 2-45remotepeer 2-48reset factory 2-52reset mappings 2-52save 2-53set 2-55set alias 2-57set chap 2-59set chassis 2-60set event_notification 2-61set fc 2-62set features 2-63set iscsi 2-64set isns 2-65set mgmt 2-66set ntp 2-68set properties 2-69set snmp 2-70set system 2-72set vpgroups 4-3show 2-74show chap 2-78show chassis 2-79show event_notification 2-81show FC 2-82show fc 4-5show fciproutes 2-83show feature_keys 2-84show features 2-85show initiators 2-86show initiators LUN mask 2-88show iostats 2-89show iscsi 2-90show isns 2-94show logs 2-95show luninfo 2-96



User’s Guide

commands (continued)show lunmask 2-100show luns 2-98show memory 2-102show mgmt 2-103show ntp 2-104show perf 2-105show portstats 2-108show presented_targets 2-112show properties 2-115show remotemaps 2-116show remotepeers 2-117show rpcinfo 2-118show snmp 2-120show stats 2-121show statsfcip 2-126show swdevices 2-119show system 2-128show targets 2-129show vpgroups 2-131, 4-2shutdown 2-133swdevices 2-134target 2-135targetmap 2-136traceroute 2-139vpgroups 2-73

communityread, setting SNMP properties A-2trap, setting SNMP properties A-2

completion, command line 2-5configurations

FCIP routes 2-83NTP, showing 2-104product information, showing 2-128router, restoring 1-5router, saving 1-4

configuringSee also configuring CHAPFC port 2-62general parameters 2-72iSCSI port 2-64management port 2-66router parameters 2-55router parameters (CHAP) 2-59

configuring (continued)SAN router 1-4SNMP parameters A-2SNMP properties 2-70SNMP trap A-3

configuring CHAPbi-directional, discovery session 3-2bi-directional, normal session 3-4uni-directional, discovery session 3-3uni-directional, normal session 3-5

connectivity, verifying 2-42contact information xivconventions xiiiconventions, typographic xiiiconverged enhanced Ethernet, definition of

Glossary-2counters (statistics), clearing 2-10CRC

definition of Glossary-1errors, MAC received 2-122, 2-123

CTRL+A keys, using 2-5CTRL+E keys, using 2-5customer support, obtaining xivcyclic redundancy check, See CRC

Ddata (persistent), saving 1-4data center Ethernet, definition of Glossary-2data migration commands 1-xidatabase

initiators, adding, changing, removing 2-26targets, removing from 2-135

dateevent A-21showing and setting 2-11

date command 2-11debug dump data, capturing 2-53debug file, creating 2-53defaults (factory), resetting 2-52definitions of terms Glossary-1deleting, See removingdestinations (trap), setting 2-70


User’s Guide


devicedefinition of Glossary-2discovery notification A-22iSCSI, discovering 2-28SmartWrite, discovering 2-119SmartWrite, removing 2-134

disabling flashing LEDs 2-8disconnected targets, removing from database

2-135discovered initiators A-9discovered targets, showing 2-129discovering

all targets on all ports 2-136iSCSI device 2-28SmartWrite devices 2-119

discovering target devices A-22discovery session

bi-directional CHAP, configuring 3-2uni-directional CHAP, configuring 3-3

documentationconventions used xiiirelated materials xii

DOWN ARROW key, using 2-5downloading and installing firmware 1-6driver, definition of Glossary-2

EEEPROM

definition of Glossary-2updated message B-16

electrically erasable programmable read-only memory, See EEPROM

enablingflashing LEDs 2-8virtual port groups 4-3

Enhanced Ethernet, definition of Glossary-2Ethernet ports

pinging 2-42showing A-20

event description A-21event log, See router log

eventsnotification, setting 2-61notification, showing 2-81severity A-20

exit command 2-12exiting the CLI 2-12, 2-30, 2-43

Ffabric

definition of Glossary-2adapter initiator ports on 4-1name server logon error B-20

fabric switch, definition of Glossary-2factory defaults, resetting 2-52failover path, definition of Glossary-2FC ports

configuring 2-62down notification A-22identifier A-8index A-8information about A-7list of A-7MIB port table A-7number of A-20parameters, configuring 2-55role/mode A-8showing information for 2-82table, MIB object group A-7type of A-9WWN A-8WWN of node A-8

FCIP, definition of Glossary-2FC-IP mode, definition of Glossary-2FCIP routes

adding 2-13configuration parameters, showing 2-83modifying 2-13notifications A-25removing 2-13

fciproute command 2-13



User’s Guide

FCoEdefinition of Glossary-2informational messages B-22, B-23

FC-P2P, See point-to-pointfeatures

license keys, showing 2-84licensed, showing 2-85setting 2-63

Fibre Channelports, targets on 2-136targets, mapping to ports 2-136targets, showing 2-129definition of Glossary-2

Fibre Channel initiators, configuring to iSCSI storage 5-1

Fibre Channel over Ethernet, See FCoEFibre Channel over IP, See FCIPFibre Channel, definition of Glossary-2field replaceable unit, See FRUfirmware

image, listing 2-25image, unpacking 2-25image, updating 2-25installing via Telnet 1-6rebooting 2-44version number, showing A-20

Flash BIOS, definition of Glossary-3Flash, definition of Glossary-3flashing LEDs, enabling 2-8frame, definition of Glossary-3FRU

blade, updating with saved configuration 1-6

configuration, saving to file 1-4definition of Glossary-3new blade, restoring 1-5

fru command 2-17fru restore command 1-6FTP

firmware image, transferring to router 1-6saving router configuration and persistence

1-4transferring data to router 1-5

Ggateway, port A-6GE ports

pinging 2-42showing A-4, A-20

generic notifications A-24gigabit Ethernet ports

pinging 2-42showing A-4, A-20

global mapping, iSCSI LUNs 2-31glossary of terms Glossary-1guest

account, defined 1-2password, changing 2-41

guideintended audience xiwhat’s in it xi

Hhardware version, showing 2-128, A-19hash value, transmitting 3-1HBA, See adapterheartbeat LED, definition of Glossary-3help command 2-18history command 2-24host bus adapter, See adapterhot replaceable/hot swappable, definition of

Glossary-3

IIANA

definition of Glossary-3FC port types registry A-9

image command 2-25initiator command 2-26initiators

adding 2-26definition of Glossary-3Fibre Channel, configuring to iSCSI storage

5-1


User’s Guide


initiators (continued)iSCSI LUN mapping 2-31LUN mask, showing 2-88mapping target LUN to 2-34mapping to target LUN 2-38modifying 2-26object table A-9removing 2-26showing information for 2-86

input/output control block, See IOCBinput/output control, See IOCTLinstalling firmware via Telnet 1-6instance (port), definition of Glossary-6intended audience for guide xiInternet Assigned Numbers Authority, See

IANAInternet protocol address, See IP addressInternet protocol, See IPInternet simple name service, See iSNSInternet small computer system interface, See

iSCSIintroduction to guide xiIOCB

command failed to execute B-21definition of Glossary-3

IOCTLdefinition of Glossary-3Fibre Channel reset request from B-21

IP, definition of Glossary-3IP address

definition of Glossary-4default, resetting 2-52port A-6port type A-6

IPv4 port type A-6IPv6 port type A-6iSCSI

device, discovering 2-28storage, configuring FC initiators to 5-1targets, showing 2-129

iSCSI, definition of Glossary-4iscsi command 2-28iSCSI nodes, CHAP configuration for 2-78

iSCSI portsconfiguring 2-64information, showing 2-90iSNS information, showing 2-94parameters, configuring 2-55targets on 2-136

iSNSblade parameters, configuring 2-65definition of Glossary-4iSCSI port, showing information 2-94

italics, meaning of xiv

Kkeystrokes, command line completion 2-5knowledge database, searching xv

Llatency, definition of Glossary-4LEDs

activity, definition of Glossary-1enabling and disabling flashing 2-8heartbeat, definition of Glossary-3

legal agreements xivlicense agreements xivlicensed features

keys, showing 2-84licensed features, showing 2-85link rate

configuring 2-62current, viewing 4-5port A-7, A-9

link status, port A-6, A-9LIP

definition of Glossary-4notification of B-21reset type B-21

load balancing, definition of Glossary-4log data, creating tar file 2-53log file, clearing entries 2-10log messages B-1



User’s Guide

logginginto iSCSI device 2-28on to router 1-1out of CLI 2-30out of iSCSI device 2-28

logical unit number (LUN), definition of Glossary-4

logout command 2-30logs

messages B-1router, showing 2-95saving 2-53

loop (arbitrated), definition of Glossary-1loop initialization process, See LIPloopback, definition of Glossary-4lunigmap command 2-31lunmask command 2-34lunremap command 2-38LUNs

definition of Glossary-4information, showing 2-96, 2-98initiators LUN mask, showing 2-88lunmask command 2-34mapping target to initiator 2-34mapping, global 2-31mappings, deleting 2-52mappings, showing 2-100tables A-12target, mapping to initiator 2-38

MMAC address

definition of Glossary-4port A-6

maintenance button, definition of Glossary-4management information base, See MIBmanagement port

configuration, showing 2-103configuring 2-66parameters, configuring 2-55pinging 2-42showing A-4

management workstation, definition of Glossary-4

mapping target LUN to initiator 2-34mapping targets A-22mappings, LUN

deleting 2-52iSCSI to initiator 2-31showing 2-100target to initiator 2-38

mappings, remoteadding 2-45modifying 2-45removing 2-45viewing 2-116

materials, related xiiMD5

CHAP, configuring 3-1definition of Glossary-4

media access control address, See MAC address

media, definition of Glossary-5memory, showing usage 2-102Message-Digest algorithm 5, See MD5MIB

definition of Glossary-5object groups, FC port table A-7object groups, network port table A-4object groups, sensor table A-16object groups, system information A-19sensor table A-16tables A-4

mid-plane, definition of Glossary-5migration commands 1-ximodifying

FCIP route 2-13initiator in database 2-26remote mappings 2-45remote peers 2-48SAN router configuration 1-4

monospace font, meaning of xiiimutual authentication

configuring CHAP (discovery session) 3-2configuring CHAP (normal session) 3-4


User’s Guide


Nnetwork packet route, printing 2-139network port down notification A-21network port table, MIB object group A-4network time protocol, See NTPnodes (iSCSI), CHAP configuration 2-78, 3-2non-volatile random access memory

(NVRAM), definition of Glossary-5normal session

bi-directional CHAP, configuring 3-4uni-directional CHAP, configuring 3-5

notifications, SNMP A-19agent shutdown A-21agent startup A-21FC port down A-22FCIP route A-25generic A-24network port down A-21objects A-20qsrAgentShutdown A-21qsrAgentStartup A-21qsrDscTgtStatusChanged A-22qsrEventTimeStamp A-21qsrFCIPRouteNotification A-25qsrFcPortDown A-22qsrGenericEvent A-24qsrPresTgtMapped A-22qsrSensorNotification A-23qsrVPGroupStatusChanged A-23sensor state A-23target device discovery A-22target presentation (mapping) A-22virtual port groups (VPGs) A-23

NTPconfiguration, showing 2-104definition of Glossary-5disabling before setting date 2-11parameters, configuring 2-68

NVRAMdefinition of Glossary-5iSCSI port contains invalid data B-15iSCSI processor failed diagnostic B-12iSCSI processor invalid B-14reboot timer failed B-12

Oobject table, initiator A-9objects

notification A-20qsrAgentVersion A-20qsrEventDescription A-21qsrEventSeverity A-20qsrHwVersion A-19qsrNoOfFcPorts A-20qsrNoOfGbEPorts A-20qsrSerialNumber A-19qsrSwVersion A-20system information A-19

online/offline targets A-22opening, administrator session 2-7operational information, showing 2-74

Pparameters

NTP, configuring 2-68router, configuring 2-55SNMP A-2system, configuring 2-72

passwd (password) command 2-41passwords

changing 2-41guest account 1-2SNMP default A-2

path, definition of Glossary-5PCM

definition of Glossary-5log messages for B-30sensor notifications A-24



User’s Guide

peers, remoteadding 2-48modifying 2-48removing 2-48viewing 2-117

performance, showing 2-105persistent data

deleting 2-52restoring 1-5saving 1-4

PID login error B-22ping command 2-42pinging ports 2-42point-to-point

definition of Glossary-5link up type B-22

portdefinition of Glossary-5instance, definition of Glossary-6

port down notification, network A-21port table

FC A-7network A-4

portsaddress mode A-5FC, configuring 2-62FC, down notification A-22FC, identifier A-8FC, index A-8FC, list of A-7FC, number of A-20FC, role/mode A-8FC, showing information for 2-82, A-7FC, type of A-9FC, WWN of node A-8indexing A-5information, showing for iSCSI 2-90IP address of A-6IP address type A-6IP address, gateway A-6IP address, subnet mask A-6iSCSI, configuring 2-64link rate A-7, A-9link status A-6, A-9

ports (continued)MAC address A-6management, configuring 2-66network, showing A-4operational role A-5statistics, showing 2-108targets, discovering on 2-136

POSTdefinition of Glossary-6processor failed message B-17

power and cooling module, See PCMpower-on self test, See POSTpre-defined guest account 1-2preface to guide xipresented iSCSI target, setting alias 2-57presented targets, showing 2-112presenting targets A-22printing network packet route 2-139product information, showing 2-128prompts, chassis and blade 2-9properties

blade, setting 2-69blade, showing 2-115

QQLogic, technical support xivqsrAgentShutdown notification A-21qsrAgentStartup notification A-21qsrAgentVersion object A-20qsrDscTgtStatusChanged notification A-22qsrEventDescription object A-21qsrEventSeverity object A-20qsrEventTimeStamp notification A-21qsrFCIPRouteNotification A-25qsrFcLinkRate table A-9qsrFcLinkStatus table A-9qsrFcPortDown notification A-22qsrFcPortEntry table A-7qsrFcPortId table A-8qsrFcPortIndex table A-8qsrFcPortNodeWwn table A-8qsrFcPortRole table A-8


User’s Guide

Index-10 ISR654601-00 E

qsrFcPortTable table A-7qsrFcPortType table A-9qsrFcPortWwn table A-8qsrGateway table A-6qsrGenericEvent notification A-24qsrHwVersion object A-19qsrIPAddress table A-6qsrIPAddressType table A-6qsrIsInit table A-9qsrIsInitAddress table A-11qsrIsInitAddressType table A-11qsrIsInitAlias table A-10qsrIsInitChapEnabled table A-11qsrIsInitEntry table A-10qsrIsInitIndex table A-10qsrIsInitName table A-10qsrIsInitOsType table A-11qsrIsInitStatus table A-11qsrLowerThreshold table A-18qsrLunEntry table A-12qsrLunProdRevLevel table A-13qsrLunProductId table A-13qsrLunSize table A-13qsrLunState table A-13qsrLunTable table A-12qsrLunVendorId table A-13qsrLunVPGroupid table A-14qsrLunVPGroupname table A-14qsrLunWwuln table A-12qsrMacAddress table A-6qsrNetMask table A-6qsrNoOfFcPorts object A-20qsrNoOfGbEPorts object A-20qsrNwLinkRate table A-7qsrNwLinkStatus table A-6qsrNwPortAddressMode table A-5qsrNwPortDown notification A-21qsrNwPortEntry table A-4qsrNwPortIndex table A-5qsrNwPortRole table A-5qsrNwPortTable table A-4qsrPresTgtMapped notification A-22qsrSensorEntry table A-16qsrSensorIndex table A-17

qsrSensorNotification notification A-23qsrSensorState table A-18qsrSensorTable table A-16qsrSensorType table A-17qsrSensorUnits table A-17qsrSensorValue table A-17qsrSerialNumber object A-19qsrSwVersion object A-20qsrUpperThreshold table A-18qsrVPGroupEntry table A-14qsrVPGroupId tables A-15qsrVPGroupIndex table A-15qsrVPGroupName table A-15qsrVPGroupStatus table A-16qsrVPGroupStatusChanged notification A-23qsrVPGroupTable table A-14qsrVPGroupWWNN table A-15qsrVPGroupWWPN table A-16quit command 2-43quitting the CLI 2-12, 2-43

Rread community, setting SNMP properties A-2reboot command 2-44reduced instruction set computer, See RISCregistered state change notification, See

RSCNrelated materials xiiremapping LUNs 2-38remote mappings

adding 2-45modifying 2-45removing 2-45viewing 2-116

remote peersadding 2-48modifying 2-48removing 2-48viewing 2-117

remote procedure call info, showing 2-118remote procedure call, See RPCremotemap command 2-45

ISR654601-00 E Index-11


User’s Guide

remotepeer command 2-48removing

FCIP route 2-13firmware image files 2-25initiator from database 2-26iSCSI global mapping 2-31LUN from initiator 2-34mappings 2-34remote mappings 2-45remote peers 2-48router log entries 2-10SmartWrite device 2-134target LUN mapping 2-38

requirements, authority 2-6reset factory command 2-52reset mappings command 2-52resetting

FC and iSCSI stat counters 2-10router parameters to default 2-52

restarting router firmware 2-44restoring

persistent data 1-5router configuration 1-5, 2-17

RISCdefinition of Glossary-6FC processor firmware failed B-17FC processor paused B-18FC processor restarted B-18iSCSI processor restarted B-16

route FCIPconfiguration parameters 2-83notifications A-25

route, network packet, tracing 2-139router, logging on to 1-1router beacon, enabling/disabling 2-8router blade, showing properties 2-115router configuration

restoring 2-17saving 2-17

router logdefinition of Glossary-6entries, clearing 2-10showing 2-95

RPCdefinition of Glossary-6error messages for B-23– B-25info, showing 2-118

RSAdefinition of Glossary-6SSH, using for router logon 1-1

RSCNdefinition of Glossary-6update received B-22

SSAN, definition of Glossary-6SAN router

configuring 1-4logging on to 1-1

SANsurfer Router Manager, definition of Glossary-6

save command 2-53saving

logs 2-53persistent data 1-4router configuration 1-4, 2-17traces 2-53

SCSI, definition of Glossary-7Secure SHell, See SSHsensor state A-18sensor state notification A-23sensor table, MIB object group A-16sensors

data measurement type A-17entry/row A-16index/identifier A-17listing all A-16lower-level threshold A-18unit of measure A-17upper-level threshold A-18value of A-17

serial number, showing 2-128, A-19session, discovery

configuring bi-directional CHAP 3-2configuring uni-directional CHAP 3-3


User’s Guide

Index-12 ISR654601-00 E

session, normalconfiguring bi-directional CHAP 3-4configuring uni-directional CHAP 3-5

set alias command 2-57set chap command 2-59set chassis command 2-60set command 2-55set event_notification command 2-61set fc command 2-62set features command 2-63set iscsi command 2-64set isns command 2-65set mgmt command 2-66set ntp command 2-68set properties command 2-69set snmp command 2-70set system command 2-72set vpgroups command 2-73, 4-3setting

alias for target 2-57date and time 2-11event notification 2-61FC port 2-62iSCSI port 2-64iSNS parameters for blade 2-65management port 2-66NTP parameters 2-68router parameters (CHAP) 2-59router parameters (general) 2-72router parameters (ports) 2-55SNMP properties and trap destinations 2-70virtual port groups 4-3

SFPAPI failed memory allocation message B-24definition of Glossary-7type, viewing 4-5

show chap command 2-78show chassis command 2-79show command 2-74show event_notification command 2-81show fc command 4-5show fciproutes command 2-83show feature_keys command 2-84show features command 2-85

show iostats command 2-89show iscsi command 2-90show isns command 2-94show logs command 2-95show luninfo command 2-96show lunmask command 2-100show memory command 2-102show mgmt command 2-103show ntp command 2-104show perf command 2-105show portstats command 2-108show presented_targets command 2-112show properties command 2-115show remotemaps command 2-116show remotepeers command 2-117show rpcinfo command 2-118show stats command 2-121show statsfcip command 2-126show swdevices command 2-119show system command 2-128show targets command 2-129show vpgroups command 2-131, 4-2showing

chassis info and status 2-79command history 2-24commands and syntax 2-18date and time 2-11FC port information 2-82FCIP route configuration 2-83initiators 2-86initiators LUN mask 2-88iSCSI port information 2-90licensed feature keys 2-84LUN information 2-96LUN information per target 2-98LUN mappings 2-100management port configuration 2-103memory usage 2-102number of FC ports A-20performance 2-105port statistics 2-108product information 2-128remote mappings 2-116remote peers 2-117

ISR654601-00 E Index-13


User’s Guide

showing (continued)router operational information 2-74RPC information 2-118SmartWrite devices 2-119SNMP 2-120statistics 2-121statistics, blade 2-126statistics, I/O 2-89system hardware version number A-19,

A-20system serial number A-19traps, configured 2-120virtual port groups 2-131, 4-2

shutdown command 2-133shutdown notification, agent A-21shutting down the system 2-133small computer system interface, See SCSIsmall form-factor pluggable, See SFPSmartWrite devices

discovering 2-119removing 2-134

SNMPdefinition of Glossary-7notifications A-19

agent shutdown A-21agent startup A-21FC port down A-22generic A-24network port down A-21objects A-20sensor state A-23

parameters, configuring A-2properties, configuring 2-70showing 2-120trap configuration A-3

software version, showing 2-128, A-20SSH

definition of Glossary-7logging on to router with 1-1

startup notification, agent A-21statistics

blade, showing 2-126counters, resetting 2-10FC and iSCSI, showing 2-121

statistics (continued)Fibre Channel port, showing 2-108GbE port, showing 2-108I/O, showing 2-89

storage area network, See SANstorage, iSCSI 5-1subnet mask, port A-6support, technical xivswdevices command 2-134switched fabric, definition of Glossary-2syntax, command 2-5system

configuring parameters 2-72hardware version number, showing A-19notification, enabling 2-61rebooting 2-44serial number, showing A-19shutting down 2-133software/firmware version number, showing

A-20system information

MIB object group A-19showing 2-128

TTAB key, using 2-5tables

FC ports A-7LUN A-12LunVPGroupid A-14MIB A-4network ports A-4qsrFcLinkRate A-9qsrFcLinkStatus A-9qsrFcPortEntry A-7qsrFcPortId A-8qsrFcPortIndex A-8qsrFcPortNodeWwn A-8qsrFcPortRole A-8qsrFcPortTable A-7qsrFcPortType A-9qsrFcPortWwn A-8


User’s Guide

Index-14 ISR654601-00 E

tables (continued)qsrGateway A-6qsrIPAddress A-6qsrIPAddressType A-6qsrIsInitAddress A-11qsrIsInitAddressType A-11qsrIsInitAlias A-10qsrIsInitChapEnabled A-11qsrIsInitEntry A-10qsrIsInitIndex A-10qsrIsInitName A-10qsrIsInitOsType A-11qsrIsInitStatus A-11qsrIsInitTable A-9qsrLowerThreshold A-18qsrLunEntry A-12qsrLunProdRevLevel A-13qsrLunProductId A-13qsrLunSize A-13qsrLunState A-13qsrLunTable A-12qsrLunVendorId A-13qsrLunVPGroupname A-14qsrLunWwuln A-12qsrMacAddress A-6qsrNetMask A-6qsrNwLinkRate A-7qsrNwLinkStatus A-6qsrNwPortAddressMode A-5qsrNwPortEntry A-4qsrNwPortIndex A-5qsrNwPortRole A-5qsrNwPortTable A-4qsrSensorEntry A-16qsrSensorIndex A-17qsrSensorState A-18qsrSensorTable A-16qsrSensorType A-17qsrSensorUnits A-17qsrSensorValue A-17qsrUpperThreshold A-18qsrVPGroupEntry A-14qsrVPGroupId A-15qsrVPGroupIndex A-15

tables (continued)qsrVPGroupName A-15qsrVPGroupStatus A-16qsrVPGroupTable A-14qsrVPGroupWWPN A-16sensor A-16virtual port groups (VPGs) A-14

target command 2-135targetmap command 2-136targets

alias, setting 2-57definition of Glossary-7discovering all on all ports 2-136discovery A-22information, showing 2-96, 2-98LUN, mapping to initiator 2-34, 2-38mapping A-22online/offline A-22presentation A-22removing from database 2-135showing discovered 2-129showing presented 2-112

technical support xivknowledge database xvobtaining xiv

Telnetdefinition of Glossary-7firmware, installing via 1-6logging on to router 1-1

temperature, showing 2-128terms and definitions Glossary-1time

event notification A-21showing and setting 2-11

traceroute command 2-139traces, saving 2-53training, technical xivtransferring data to router using FTP 1-5transmitting hash value 3-1traps

authentication, enabling A-2community, setting SNMP properties A-2configuration, SNMP A-3

ISR654601-00 E Index-15


User’s Guide

traps (continued)configured, showing 2-120destinations, setting 2-70

troubleshootingQLogic knowledge database xv

typographic conventions xiii

Uuni-directional CHAP

discovery session, configuring for 3-3normal session, configuring for 3-5

unpacking firmware image file 2-25UP ARROW key, using 2-5updating

blade with saved configuration data 1-5firmware image 2-25

URL, event notification 2-61usage, CLI 1-1

Vverifying connectivity (ping command) 2-42version number

hardware, showing A-19hardware/software, showing 2-128software/firmware, showing A-20

virtual logical area network, See VLANvirtual port groups (VPGs) 4-1

definition of Glossary-8enabling 4-3notifications A-23setting 2-73, 4-3showing 2-131, 4-2tables A-14

VLANconfiguration change message B-27definition of Glossary-7enabling/disabling 2-64

VPGs, See virtual port groups

Wwhat’s in this guide xiworkstation (management), definition of

Glossary-4world wide name, See WWNworld wide node name, See WWNNworld wide port name, See WWPNworld wide unique LUN name, See WWULNWWN

definition of Glossary-8Fibre Channel port A-8

WWNNdefinition of Glossary-8login message B-9

WWPNdefinition of Glossary-8login message B-9with virtual port groups 4-4

WWULNdefinition of Glossary-8viewing for LUN A-12

Corporate Headquarters QLogic Corporation 26650 Aliso Viejo Parkway Aliso Viejo, CA 92656 949.389.6000 www.qlogic.com

International Offices UK | Ireland | Germany | France | India | Japan | China | Hong Kong | Singapore | Taiwan

© 2009–2011 QLogic Corporation. Specifications are subject to change without notice. All rights reserved worldwide. QLogic, the QLogic logo, and SmartWrite are trademarks or registered trademarks of QLogic Corporation. Linux is a registered trademark of Linus Torvalds. Microsoft and Windows are registered trademarks of Microsoft Corporation. All other brand and product names are trademarks or registered trademarks of their respective owners. Information supplied by QLogic Corporation is believed to be accurate and reliable. QLogic Corporation assumes no responsibility for any errors in this brochure. QLogic Corporation reserves the right, without notice, to make changes in product design or specifications.

www.qlogic.com

isr6200 command line interface (cli) user’s...

Documents