iso quant managerial economics

Copyright © 2008 by the McGraw-Hill Companies, Inc. All rights reserved.

McGraw-Hill/IrwinManagerial Economics, 9e

Managerial Economics ThomasMauriceninth edition

Copyright © 2008 by the McGraw-Hill Companies, Inc. All rights reserved.

McGraw-Hill/IrwinManagerial Economics, 9e

Managerial Economics ThomasMauriceninth edition

Chapter 9

Production & Cost in the Long Run

Managerial EconomicsManagerial Economics

9-2

Production Isoquants

• In the long run, all inputs are variable & isoquants are used to study production decisions• An isoquant is a curve showing all

possible input combinations capable of producing a given level of output

• Isoquants are downward sloping; if greater amounts of labor are used, less capital is required to produce a given output


9-3

Typical Isoquants (Figure 9.1)


9-4

Marginal Rate of Technical Substitution• The MRTS is the slope of an isoquant

& measures the rate at which the two inputs can be substituted for one another while maintaining a constant level of output

K

MRTSL

MRTS

K LThe minus sign is added to make a positivenumber since , the slope of the isoquant, isnegative


9-5

Marginal Rate of Technical Substitution• The MRTS can also be expressed as

the ratio of two marginal products:

L

K

MPMRTS

MP

L

K

MPMP MRTSAs labor is substituted f or capital, declines &

rises causing to diminish

L

K

MPKMRTS

L MP


9-6

Isocost Curves

• Represents amount of capital that may be purchased if zero labor is purchased

( C ) ( w, r )

Show various combinations of inputs thatmay be purchased for given level ofexpenditure at given input prices

•

• K C r-intercept is

C w

K Lr r

•( w r )

Slope of an isocost curve is the negativeof the input price ratio


9-7

Isocost Curves (Figures 9.2 & 9.3)


9-8

Optimal Combination of Inputs

• Two slopes are equal in equilibrium• Implies marginal product per dollar spent on

last unit of each input is the same

Q

Q

Minimize total cost of producing bychoosing the input combination on the

isoquant for which is just tangent to anisocost curve

•

L L K

K

MP MP MPw

MP r w ror


9-9

Optimal Input Combination to Minimize Cost for Given Output (Figure 9.4)


9-10

Optimization & Cost

• Expansion path gives the efficient (least-cost) input combinations for every level of output• Derived for a specific set of input

prices• Along expansion path, input-price

ratio is constant & equal to the marginal rate of technical substitution


9-11

Expansion Path (Figure 9.6)


9-12

Returns to Scale

• If all inputs are increased by a factor of c & output goes up by a factor of z then, in general, a producer experiences:• Increasing returns to scale if z > c; output goes up

proportionately more than the increase in input usage

• Decreasing returns to scale if z < c; output goes up proportionately less than the increase in input usage

• Constant returns to scale if z = c; output goes up by the same proportion as the increase in input usage

f(cL, cK) = zQ


9-13

Long-Run Costs

• Long-run total cost (LTC) for a given level of output is given by: LTC = wL* + rK* Where w & r are prices of labor & capital,

respectively, & (L*, K*) is the input combination on the expansion path that minimizes the total cost of producing that output


9-14

Long-Run Costs• Long-run average cost (LAC) measures the

cost per unit of output when production can be adjusted so that the optimal amount of each input is employed• LAC is U-shaped

• Falling LAC indicates economies of scale

• Rising LAC indicates diseconomies of scale

LTC

LACQ


9-15

Long-Run Costs• Long-run marginal cost (LMC) measures

the rate of change in long-run total cost as output changes along expansion path• LMC is U-shaped

• LMC lies below LAC when LAC is falling

• LMC lies above LAC when LAC is rising

• LMC = LAC at the minimum value of LAC

LTC

LMCQ


9-16

Derivation of a Long-Run Cost Schedule (Table 9.1)

Least-cost combination of

Output Labor (units)

Capital (units)

Total cost

(w = $5, r = $10)

LAC LMC

100

500

600

200

300

400

700

LMC

10

4052

1220

30

60

7

2230

8

10

15

42

$120

420

560

140

200

300

720

$1.20

0.840.93

0.700.67

0.75

1.03

$1.20

1.201.40

0.200.60

1.00

1.60


9-17

Long-Run Total, Average, & Marginal Cost (Figure 9.9)


9-18

Long-Run Average & Marginal Cost Curves (Figure 9.10)


9-19

Various Shapes of LAC (Figure 9.11)


9-20

Constant Long-Run Costs

• When constant returns to scale occur over entire range of output• Firm experiences constant costs in

the long run• LAC curve is flat & equal to LMC at

all output levels


9-21

Constant Long-Run Costs (Figure 9.12)


9-22

Economies of Scope

• Exist for a multi-product firm when the joint cost of producing two or more goods is less than the sum of the separate costs of producing the two goods

• For two goods, X & Y, economies of scope exist when:

C(X, Y) < C(X) + C(Y)• Diseconomies of scope exist when:

C(X, Y) > C(X) + C(Y)


9-23

Relations Between Short-Run & Long-Run Costs• LMC intersects LAC when the latter is at its

minimum point

• At each output where a particular ATC is tangent to LAC, the relevant SMC = LMC

• For all ATC curves, point of tangency with LAC is at an output less (greater) than the output of minimum ATC if the tangency is at an output less (greater) than that associated with minimum LAC


9-24

Long-Run Average Cost as the Planning Horizon (Figure 9.13)


9-25

Restructuring Short-Run Costs

• Because managers have greatest flexibility to choose inputs in the long run, costs are lower in the long run than in the short run for all output levels except that for which the fixed input is at its optimal level• Short-run costs can be reduced by

adjusting fixed inputs to their optimal long-run levels when the opportunity arises


9-26

Restructuring Short-Run Costs (Figure 9.14)

iso quant managerial economics

Economy & Finance

lac lmc

given output

long run lac curve

cost input combinations

marginal cost lmc

average cost lac

output level

output figure