ise
DESCRIPTION
iseTRANSCRIPT
-
Cisco Wireless LAN Controller Command Reference, Release 7.3First Published: August 28, 2012
Last Modified: October 25, 2012
Americas HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706USAhttp://www.cisco.comTel: 408 526-4000 800 553-NETS (6387)Fax: 408 527-0883
Text Part Number: OL-27543-01
-
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS,INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITEDWARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITHTHE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY,CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB's public domain versionof the UNIX operating system. All rights reserved. Copyright 1981, Regents of the University of California.
NOTWITHSTANDINGANYOTHERWARRANTYHEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED AS IS"WITH ALL FAULTS.CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OFMERCHANTABILITY, FITNESS FORA PARTICULAR PURPOSEANDNONINFRINGEMENTORARISING FROMACOURSEOFDEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUTLIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERSHAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, networktopology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentionaland coincidental.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: http://www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnershiprelationship between Cisco and any other company. (1110R)
2012 Cisco Systems, Inc. All rights reserved.
-
C O N T E N T S
P r e f a c e Preface xli
Audience xli
Document Organization xli
Document Conventions xli
Related Documentation xliv
Obtaining Documentation and Submitting a Service Request xliv
C H A P T E R 1 Using the Command-Line Interface 1
CLI Command Keyboard Shortcuts 1
Using the Interactive Help Feature 2
Using the help Command 3
Using the ? command 3
Using the partial? command 4
Using the partial command 4
Using the command ? 5
command keyword ? 6
C H A P T E R 2 CLI Commands 7
CLI Commands 8
Show Commands 9
show 802.11 10
show 802.11 cleanair 12
show 802.11 cleanair air-quality summary 14
show 802.11 cleanair air-quality worst 15
show 802.11 cleanair device ap 16
show 802.11 cleanair device type 17
show 802.11 cu-metrics 19
Cisco Wireless LAN Controller Command Reference, Release 7.3 OL-27543-01 iii
-
show 802.11 extended 20
show 802.11 media-stream 21
Show Advanced Commands 22
show advanced 802.11 channel 23
show advanced 802.11 coverage 24
show advanced 802.11 group 25
show advanced 802.11 l2roam 26
show advanced 802.11 logging 27
show advanced 802.11 monitor 28
show advanced 802.11 profile 29
show advanced 802.11 receiver 30
show advanced 802.11 summary 31
show advanced 802.11 txpower 32
show advanced backup-controller 33
show advanced client-handoff 34
show advanced dot11-padding 35
show advanced eap 36
show advanced hotspot 37
show advanced max-1x-sessions 38
show advanced probe 39
show advanced rate 40
show advanced send-disassoc-on-handoff 41
show advanced sip-preferred-call-no 42
show advanced sip-snooping-ports 43
show advanced statistics 44
show advanced timers 45
Show Access Point Commands 46
show ap auto-rf 47
show ap ccx rm 49
show ap cdp 50
show ap channel 52
show ap config 53
show ap config global 59
show ap core-dump 60
show ap crash-file 61
Cisco Wireless LAN Controller Command Reference, Release 7.3iv OL-27543-01
Contents
-
show ap data-plane 62
show ap ethernet tag 63
show ap eventlog 64
show ap image 65
show ap inventory 66
show ap join stats detailed 67
show ap join stats summary 68
show ap join stats summary all 69
show ap led-state 70
show ap link-encryption 71
show ap monitor-mode summary 72
show ap packet-dump status 73
show ap retransmit 74
show ap stats 75
show ap summary 78
show ap tcp-mss-adjust 79
show ap wlan 80
Show CAC Commands 80
show cac voice stats 81
show cac voice summary 82
show cac video stats 83
show cac video summary 85
Show Client Commands 86
show client ap 87
show client calls 88
show client ccx client-capability 89
show client ccx frame-data 90
show client ccx last-response-status 91
show client ccx last-test-status 92
show client ccx log-response 93
show client ccx manufacturer-info 95
show client ccx operating-parameters 96
show client ccx profiles 97
show client ccx results 99
show client ccx rm 100
Cisco Wireless LAN Controller Command Reference, Release 7.3 OL-27543-01 v
Contents
-
show client ccx stats-report 102
show client detail 103
show client location-calibration summary 105
show client probing 106
show client roam-history 107
show client summary 108
show client summary guest-lan 109
show client tsm 110
show client username 112
show client voice-diag 113
Show IPv6 Commands 114
show ipv6 acl 115
show ipv6 neighbor-binding 116
show ipv6 ra-guard 120
show ipv6 summary 121
Show Media-Stream Commands 122
show media-stream client 123
show media-stream group detail 124
show media-stream group summary 125
show mesh Commands 126
show mesh ap 127
show mesh astools stats 128
show mesh backhaul 129
show mesh cac 130
show mesh client-access 132
show mesh config 133
show mesh env 134
show mesh neigh 135
show mesh path 138
show mesh per-stats 139
show mesh queue-stats 140
show mesh public-safety 141
show mesh security-stats 142
show mesh stats 144
Show Mobility Commands 145
Cisco Wireless LAN Controller Command Reference, Release 7.3vi OL-27543-01
Contents
-
show mobility anchor 146
show mobility ap-list 147
show mobility foreign-map 148
show mobility group member 149
show mobility statistics 150
show mobility summary 151
Show Proxy Mobility IPv6 (PMIPv6) Commands 151
show pmipv6 domain 152
show pmipv6 mag bindings 153
show pmipv6 mag globals 154
show pmipv6 mag stats 155
show pmipv6 profile summary 157
Show RADIUS Commands 158
show radius acct statistics 159
show radius auth statistics 160
show radius rfc3576 statistics 161
show radius summary 162
Show Radio Frequency ID Commands 163
show rfid client 164
show rfid config 165
show rfid detail 166
show rfid summary 167
Show Redundancy Commands 168
show redundancy summary 169
show redundancy latency 170
show redundancy interfaces 171
show redundancy mobilitymac 172
show redundancy peer-route summary 173
show redundancy statistics 174
show redundancy timers 175
Show RF-Profile Commands 176
show rf-profile summary 177
show rf-profile details 178
Show Rogue Commands 179
show rogue adhoc detailed 180
Cisco Wireless LAN Controller Command Reference, Release 7.3 OL-27543-01 vii
Contents
-
show rogue adhoc summary 182
show rogue ap clients 183
show rogue ap detailed 185
show rogue ap summary 187
show rogue ap friendly summary 190
show rogue ap malicious summary 192
show rogue ap unclassified summary 194
show rogue auto-contain 195
show rogue client detailed 196
show rogue client summary 197
show rogue ignore-list 198
show rogue rule detailed 200
show rogue rule summary 201
Show TACACS Commands 202
show tacacs acct statistics 203
show tacacs athr statistics 204
show tacacs auth statistics 205
show tacacs summary 206
Show WPS Commands 207
show wps ap-authentication summary 208
show wps cids-sensor 209
show wps mfp 210
show wps shun-list 212
show wps signature detail 213
show wps signature events 214
show wps signature summary 216
show wps summary 218
show wps wips statistics 220
show wps wips summary 221
Other Show Commands 221
show aaa auth 222
show acl 223
show acl cpu 225
show arp kernel 226
show arp switch 227
Cisco Wireless LAN Controller Command Reference, Release 7.3viii OL-27543-01
Contents
-
show auth-list 228
show boot 229
show band-select 230
show buffers 231
show cdp 233
show call-control ap 234
show call-control client 238
show capwap client config 239
show capwap client ip config 240
show capwap reap association 241
show capwap reap status 242
show certificate compatibility 243
show certificate lsc 244
show certificate ssc 245
show certificate summary 246
show route kernel 247
show country 248
show country channels 249
show country supported 250
show coredump summary 252
show cpu 253
show custom-web all 254
show database summary 255
show debug 256
show dhcp 258
show dtls connections 259
show dhcp proxy 260
show dhcp timeout 261
show eventlog 262
show exclusionlist 263
show flexconnect acl detailed 264
show flexconnect acl summary 265
show guest-lan 266
show flexconnect group detail 267
show flexconnect group summary 268
Cisco Wireless LAN Controller Command Reference, Release 7.3 OL-27543-01 ix
Contents
-
show flexconnect office-extend 269
show ike 270
show interface detailed 271
show interface group 273
show invalid-config 275
show inventory 276
show IPsec 277
show known ap 279
show l2tp 280
show lag eth-port-hash 281
show lag ip-port-hash 282
show lag summary 283
show ldap 284
show ldap statistics 285
show ldap summary 286
show license agent 287
show license all 288
show license capacity 290
show license detail 291
show license expiring 292
show license evaluation 293
show license feature 294
show license file 295
show license handle 296
show license image-level 297
show license in-use 298
show license permanent 299
show license status 300
show license statistics 301
show license summary 302
show license udi 303
show load-balancing 304
show local-auth certificates 305
show local-auth config 306
show local-auth statistics 308
Cisco Wireless LAN Controller Command Reference, Release 7.3x OL-27543-01
Contents
-
show location 310
show location statistics rfid 311
show logging 312
show loginsession 314
show macfilter 315
show memory monitor 316
show mgmtuser 317
show msglog 318
show nac statistics 319
show nac summary 320
show netuser 321
show netuser guest-roles 322
show network 323
show network summary 324
show network multicast mgid detail 326
show network multicast mgid summary 327
show nmsp notify-interval summary 328
show nmsp statistics 329
show nmsp status 331
show nmsp subscription 332
show ntp-keys 333
show pmk-cache 334
show port 335
show process 337
show qos 338
show reset 339
show remote-lan 340
show route summary 342
show rules 343
show run-config 344
show serial 345
show sessions 346
show snmpcommunity 347
show snmpengineID 348
show snmptrap 349
Cisco Wireless LAN Controller Command Reference, Release 7.3 OL-27543-01 xi
Contents
-
show snmpv3user 350
show snmpversion 351
show spanningtree port 352
show spanningtree switch 353
show stats port 354
show stats switch 356
show switchconfig 358
show sysinfo 359
show tech-support 360
show time 361
show trapflags 363
show traplog 365
show version 366
show watchlist 367
show wlan 368
Config 802.11-a Commands 371
config 802.11-a 372
config 802.11-a antenna extAntGain 373
config 802.11-a channel ap 374
config 802.11-a txpower ap 375
Configure 802.11b Commands 376
config 802.11b 11gSupport 377
config 802.11b preamble 378
Configure 802.11h Commands 379
config 802.11h channelswitch 380
config 802.11h powerconstraint 381
config 802.11h setchannel 382
Configure 802.11 11n Support Commands 383
config 802.11 11nsupport 384
config 802.11 11nsupport a-mpdu tx priority 385
config 802.11 11nsupport a-mpdu tx scheduler 387
config 802.11 11nsupport antenna 388
config 802.11 11nsupport guard-interval 389
config 802.11 11nsupport mcs tx 390
config 802.11 11nsupport rifs 392
Cisco Wireless LAN Controller Command Reference, Release 7.3xii OL-27543-01
Contents
-
Configure 802.11 Antenna Commands 393
config 802.11 antenna diversity 394
config 802.11 antenna extAntGain 395
config 802.11 antenna mode 396
config 802.11 antenna selection 397
Configure 802.11 CleanAir Commands 398
config 802.11 cleanair 399
config 802.11 cleanair device 401
config 802.11 cleanair alarm 403
Configure 802.11 CAC Commands 405
config 802.11 cac defaults 406
config 802.11 cac video acm 408
config 802.11 cac video cac-method 410
config 802.11 cac video load-based 412
config 802.11 cac video max-bandwidth 414
config 802.11 cac media-stream 416
config 802.11 cac multimedia 418
config 802.11 cac video roam-bandwidth 420
config 802.11 cac video sip 422
config 802.11 cac video tspec-inactivity-timeout 424
config 802.11 cac voice acm 426
config 802.11 cac voice max-bandwidth 427
config 802.11 cac voice roam-bandwidth 429
config 802.11 cac voice tspec-inactivity-timeout 431
config 802.11 cac voice load-based 433
config 802.11 cac voice max-calls 435
config 802.11 cac voice sip bandwidth 437
config 802.11 cac voice sip codec 439
config 802.11 cac voice stream-size 441
Config 802.11 Commands 442
config 802.11 beacon period 443
config 802.11 beamforming 444
config 802.11 channel 446
config 802.11 channel ap 448
config 802.11 chan_width 449
Cisco Wireless LAN Controller Command Reference, Release 7.3 OL-27543-01 xiii
Contents
-
config 802.11 disable 451
config 802.11 dtpc 452
config 802.11 enable 453
config 802.11 exp-bwreq 454
config 802.11 fragmentation 455
config 802.11 l2roam rf-params 456
config 802.11 max-clients 458
config 802.11 multicast data-rate 459
config 802.11 rate 460
config 802.11 tsm 461
config 802.11 txPower 462
Configure Advanced 802.11 Commands 464
config advanced 802.11 7920VSIEConfig 465
Configure Advanced 802.11 Channel Commands 466
config advanced 802.11 channel add 467
config advanced 802.11 channel cleanair-event 468
config advanced 802.11 channel dca anchor-time 469
config advanced 802.11 channel dca chan-width-11n 470
config advanced 802.11 channel dca interval 471
config advanced 802.11 channel dca min-metric 472
config advanced 802.11 channel dca sensitivity 473
config advanced 802.11 channel foreign 475
config advanced 802.11 channel load 476
config advanced 802.11 channel noise 477
config advanced 802.11 channel outdoor-ap-dca 478
config advanced 802.11 channel pda-prop 479
config advanced 802.11 channel update 480
Configure Advanced 802.11 Coverage Commands 481
config advanced 802.11 coverage 482
config advanced 802.11 coverage exception global 484
config advanced 802.11 coverage fail-rate 486
config advanced 802.11 coverage level global 488
config advanced 802.11 coverage packet-count 490
config advanced 802.11 coverage rssi-threshold 492
Configure Advanced 802.11 Logging Commands 494
Cisco Wireless LAN Controller Command Reference, Release 7.3xiv OL-27543-01
Contents
-
config advanced 802.11 logging channel 495
config advanced 802.11 logging coverage 496
config advanced 802.11 logging foreign 497
config advanced 802.11 logging load 498
config advanced 802.11 logging noise 499
config advanced 802.11 logging performance 500
config advanced 802.11 logging txpower 501
Configure Advanced 802.11 Monitor Commands 502
config advanced 802.11 monitor channel-list 503
config advanced 802.11 monitor coverage 504
config advanced 802.11 monitor load 505
config advanced 802.11 monitor mode 506
config advanced 802.11 monitor ndp-type 507
config advanced 802.11 monitor noise 508
config advanced 802.11 monitor signal 509
Configure Advanced 802.11 Profile Commands 510
config advanced 802.11 profile clients 511
config advanced 802.11 profile customize 512
config advanced 802.11 profile foreign 513
config advanced 802.11 profile noise 514
config advanced 802.11 profile throughput 515
config advanced 802.11 profile utilization 516
Other Config Advanced Commands 516
config advanced 802.11 receiver 517
config advanced 802.11 edca-parameters 518
config advanced 802.11 factory 520
config advanced 802.11 group-member 521
config advanced 802.11 group-mode 522
config advanced 802.11 tpc-version 523
config advanced 802.11 tpcv1-thresh 524
config advanced 802.11 tpcv2-intense 525
config advanced 802.11 tpcv2-per-chan 526
config advanced 802.11 tpcv2-thresh 527
config advanced 802.11 txpower-update 528
config advanced backup-controller primary 529
Cisco Wireless LAN Controller Command Reference, Release 7.3 OL-27543-01 xv
Contents
-
config advanced backup-controller secondary 530
config advanced client-handoff 531
config advanced dot11-padding 532
config advanced assoc-limit 533
config advanced eap 534
config advanced fastpath fastcache 536
config advanced fastpath pkt-capture 537
config advanced hotspot 538
config advanced max-1x-sessions 540
config advanced rate 541
config advanced sip-preferred-call-no 542
config advanced sip-snooping-ports 543
config advanced statistics 544
config advanced probe filter 545
config advanced probe limit 546
Configure Advanced Timers Commands 547
config advanced timers 548
config advanced timers ap-fast-heartbeat 551
config advanced timers ap-heartbeat-timeout 552
config advanced timers ap-primary-discovery-timeout 553
config advanced timers auth-timeout 554
config advanced timers eap-timeout 555
config advanced timers eap-identity-request-delay 556
Configure Access Point Commands 557
config ap 558
config ap bhrate 559
config ap autoconvert 560
config ap bhrate 561
config ap bridgegroupname 562
config ap bridging 563
config ap cdp 564
config ap core-dump 566
config ap crash-file clear-all 567
config ap crash-file delete 568
config ap crash-file get-crash-file 569
Cisco Wireless LAN Controller Command Reference, Release 7.3xvi OL-27543-01
Contents
-
config ap crash-file get-radio-core-dump 570
config ap 802.1Xuser 571
config ap 802.1Xuser delete 572
config ap 802.1Xuser disable 573
config ap ethernet duplex 574
config ap ethernet duplex 575
config ap group-name 576
config ap flexconnect central-dhcp 577
config ap flexconnect local-split 579
config ap flexconnect radius auth set 580
config ap flexconnect vlan 581
config ap flexconnect vlan add 582
config ap flexconnect vlan native 583
config ap flexconnect vlan wlan 584
config ap flexconnect web-auth 585
config ap flexconnect web-policy acl 586
config ap hotspot 587
config ap image predownload 594
config ap image swap 595
config ap led-state 596
config ap link-encryption 597
config ap link-latency 598
config ap location 599
config ap logging syslog level 600
config ap mgmtuser add 602
config ap mgmtuser delete 604
config ap mode 605
config ap monitor-mode 607
config ap name 608
config ap packet-dump 609
config ap port 612
config ap power injector 613
config ap power pre-standard 614
config ap primary-base 615
config ap priority 616
Cisco Wireless LAN Controller Command Reference, Release 7.3 OL-27543-01 xvii
Contents
-
config ap reporting-period 617
config ap reset 618
config ap retransmit interval 619
config ap retransmit count 620
config ap role 621
config ap rst-button 622
config ap secondary-base 623
config ap sniff 624
config ap ssh 626
config ap static-ip 627
config ap stats-timer 629
config ap syslog host global 630
config ap syslog host specific 631
config ap tcp-mss-adjust 632
config ap telnet 634
config ap tertiary-base 635
config ap tftp-downgrade 636
config ap username 637
config ap venue 638
config ap wlan 642
Configure Band-Select Commands 643
config band-select cycle-count 644
config band-select cycle-threshold 645
config band-select expire 646
config band-select client-rssi 647
Configure Client Commands 648
config client ccx clear-reports 649
config client ccx clear-results 650
config client ccx default-gw-ping 651
config client ccx dhcp-test 652
config client ccx dns-ping 653
config client ccx dns-resolve 654
config client ccx get-client-capability 655
config client ccx get-manufacturer-info 656
config client ccx get-operating-parameters 657
Cisco Wireless LAN Controller Command Reference, Release 7.3xviii OL-27543-01
Contents
-
config client ccx get-profiles 658
config client ccx log-request 659
config client ccx send-message 661
config client ccx stats-request 664
config client ccx test-abort 665
config client ccx test-association 666
config client ccx test-dot1x 667
config client ccx test-profile 668
config client deauthenticate 669
config client location-calibration 670
Configure Guest-LAN Commands 671
config guest-lan 672
config guest-lan custom-web ext-webauth-url 673
config guest-lan custom-web global disable 674
config guest-lan custom-web login_page 675
config guest-lan custom-web webauth-type 676
config guest-lan ingress-interface 677
config guest-lan interface 678
config guest-lan mobility anchor 679
config guest-lan nac 680
config guest-lan security 681
Configure IPv6 Commands 682
config ipv6 disable 683
config ipv6 enable 684
config ipv6 acl 685
config ipv6 neighbor-binding 688
config ipv6 ns-mcast-fwd 690
config ipv6 ra-guard 691
Configure Interface Group Commands 692
config interface group 693
Configure Macfilter Commands 694
config macfilter add/delete 695
config macfilter description 697
config macfilter interface 698
config macfilter ip-address 699
Cisco Wireless LAN Controller Command Reference, Release 7.3 OL-27543-01 xix
Contents
-
config macfilter mac-delimiter 700
config macfilter radius-compat 701
config macfilter wlan-id 702
config macfilter wlan-id 703
Config Remote LAN Commands 703
config remote-lan 704
config remote-lan aaa-override 705
config remote-lan acl 706
config remote-lan create 707
config remote-lan custom-web 708
config remote-lan delete 710
config remote-lan dhcp_server 711
config remote-lan exclusionlist 712
config remote-lan interface 713
config remote-lan ldap 714
config remote-lan mac-filtering 715
config remote-lan max-associated-clients 716
config remote-lan radius_server 717
config remote-lan security 719
config remote-lan session-timeout 720
config remote-lan webauth-exclude 721
Configure Memory Monitor Commands 722
config memory monitor errors 723
config memory monitor leaks 724
Configure Mesh Commands 726
config mesh alarm 727
config mesh astools 728
config mesh backhaul rate-adapt 729
config mesh backhaul slot 730
config mesh battery-state 731
config mesh client-access 732
config mesh ethernet-bridging vlan-transparent 733
config mesh full-sector-dfs 734
config mesh linkdata 735
config mesh linktest 737
Cisco Wireless LAN Controller Command Reference, Release 7.3xx OL-27543-01
Contents
-
config mesh lsc 740
config mesh multicast 741
config mesh parent preferred 743
config mesh public-safety 744
config mesh radius-server 745
config mesh range 746
config mesh secondary-backhaul 747
config mesh security 748
config mesh slot-bias 750
Configure Management-User Commands 751
config mgmtuser add 752
config mgmtuser delete 753
config mgmtuser description 754
config mgmtuser password 755
Configure Mobility Commands 756
config mobility dscp 757
config mobility group anchor 758
config mobility group domain 759
config mobility group keepalive count 760
config mobility group keepalive interval 761
config mobility group member 762
config mobility group multicast-address 764
config mobility multicast-mode 765
config mobility secure-mode 766
config mobility statistics reset 767
Configure Message Log Level Commands 768
config msglog level critical 769
config msglog level error 770
config msglog level security 771
config msglog level verbose 772
config msglog level warning 773
Configure Media-Stream Commands 774
config 802.11 media-stream multicast-direct 775
config 802.11 media-stream video-redirect 777
config media-stream multicast-direct 778
Cisco Wireless LAN Controller Command Reference, Release 7.3 OL-27543-01 xxi
Contents
-
config media-stream message 779
config media-stream add 781
config media-stream admit 783
config media-stream deny 784
config media-stream delete 785
Configure Net User Commands 786
config netuser add 787
config netuser delete 789
config netuser description 790
config netuser guest-lan-id 791
config netuser guest-role apply 792
config netuser guest-role create 793
config netuser guest-role delete 794
config netuser guest-role qos data-rate average-data-rate 795
config netuser guest-role qos data-rate average-realtime-rate 796
config netuser guest-role qos data-rate burst-data-rate 797
config netuser guest-role qos data-rate burst-realtime-rate 798
config netuser lifetime 799
config netuser maxUserLogin 800
config netuser password 801
config netuser wlan-id 802
Configure Network Commands 803
config network 802.3-bridging 804
config network allow-old-bridge-aps 805
config network ap-discovery 806
config network ap-fallback 807
config network ap-priority 808
config network apple-talk 809
config network arptimeout 810
config network bridging-shared-secret 811
config network broadcast 812
config network client-ip-conflict-detection 813
config network fast-ssid-change 814
config network ip-mac-binding 815
config network master-base 816
Cisco Wireless LAN Controller Command Reference, Release 7.3xxii OL-27543-01
Contents
-
config network mgmt-via-wireless 817
config network multicast global 818
config network multicast igmp query interval 819
config network multicast igmp snooping 820
config network multicast igmp timeout 821
config network multicast l2mcast 822
config network multicast mld 823
config network multicast mode multicast 824
config network multicast mode unicast 825
config network oeap-600 dual-rlan-ports 826
config network oeap-600 local-network 827
config network otap-mode 828
config network rf-network-name 829
config network secureweb 830
config network secureweb cipher-option 831
config network ssh 833
config network telnet 834
config network usertimeout 835
config network web-auth captive-bypass 836
config network web-auth cmcc-support 837
config network web-auth port 838
config network web-auth proxy-redirect 839
config network web-auth secureweb 840
config network webmode 841
config network web-auth 842
config network zero-config 843
Configure Port Commands 844
config port adminmode 845
config port autoneg 846
config port linktrap 847
config port multicast appliance 848
config port power 849
Configure PMIPv6 Commands 850
config pmipv6 domain 851
config pmipv6 add profile 852
Cisco Wireless LAN Controller Command Reference, Release 7.3 OL-27543-01 xxiii
Contents
-
config pmipv6 delete 854
config pmipv6 mag binding init-retx-time 855
config pmipv6 mag binding lifetime 856
config pmipv6 mag binding max-retx-time 857
config pmipv6 mag binding maximum 858
config pmipv6 mag binding refresh-time 859
config pmipv6 mag bri delay 860
config pmipv6 mag bri retries 861
config pmipv6 mag lma 862
config pmipv6 mag replay-protection 863
Configure QoS Commands 863
config qos average-data-rate 864
config qos average-realtime-rate 866
config qos burst-data-rate 868
config qos burst-realtime-rate 870
config qos description 872
config qos max-rf-usage 873
config qos dot1p-tag 874
config qos priority 875
config qos protocol-type 877
config qos queue_length 878
Configure RADIUS Account Commands 879
config radius acct 880
config radius acct ipsec authentication 883
config radius acct ipsec disable 884
config radius acct ipsec enable 885
config radius acct ipsec encryption 886
config radius acct ipsec ike 887
config radius acct mac-delimiter 888
config radius acct network 889
config radius acct retransmit-timeout 890
Configure RADIUS Authentication Server Commands 891
config radius auth 892
config radius auth callStationIdType 894
config radius auth IPsec authentication 896
Cisco Wireless LAN Controller Command Reference, Release 7.3xxiv OL-27543-01
Contents
-
config radius auth ipsec disable 897
config radius auth ipsec encryption 898
config radius auth ipsec ike 899
config radius auth keywrap 901
config radius auth mac-delimiter 902
config radius auth management 903
config radius auth mgmt-retransmit-timeout 904
config radius auth network 905
config radius auth retransmit-timeout 906
config radius auth rfc3576 907
config radius auth retransmit-timeout 908
config radius aggressive-failover disabled 909
config radius backward compatibility 910
config radius callStationIdCase 911
config radius callStationIdType 912
config radius fallback-test 914
Configure Redundancy Commands 915
config redundancy interface address peer-service-port 916
config redundancy mobilitymac 917
config redundancy mode 918
config redundancy peer-route 919
config redundancy timer keep-alive-timer 920
config redundancy timer peer-search-timer 921
config redundancy unit 922
redundancy force-switchover 923
config interface address redundancy-management 924
Configure RF-Profile commands 926
config rf-profile band-select 927
config rf-profile client-trap-threshold 929
config rf-profile create 930
config rf-profile coverage 931
config rf-profile data-rates 933
config rf-profile delete 934
config rf-profile description 935
config rf-profile load-balancing 936
Cisco Wireless LAN Controller Command Reference, Release 7.3 OL-27543-01 xxv
Contents
-
config rf-profile max-clients 937
config rf-profile multicast data-rate 938
config rf-profile out-of-box 939
config rf-profile tx-power-control-thresh-v1 940
config rf-profile tx-power-control-thresh-v2 941
config rf-profile tx-power-max 942
config rf-profile tx-power-min 943
Configure Rogue Commands 944
config rogue adhoc 945
config rogue ap classify 947
config rogue ap friendly 949
config rogue ap rldp 951
config rogue ap ssid 953
config rogue ap timeout 955
config rogue auto-contain level 957
config rogue ap valid-client 959
config rogue client 961
config rogue detection 963
config rogue detection min-rssi 965
config rogue detection monitor-ap 966
config rogue rule 968
Configure SNMP Commands 971
config snmp community accessmode 972
config snmp community create 973
config snmp community delete 974
config snmp community ipaddr 975
config snmp community mode 976
config snmp engineID 977
config snmp syscontact 978
config snmp syslocation 979
config snmp trapreceiver create 980
config snmp trapreceiver delete 981
config snmp trapreceiver mode 982
config snmp v3user create 983
config snmp v3user delete 985
Cisco Wireless LAN Controller Command Reference, Release 7.3xxvi OL-27543-01
Contents
-
config snmp version 986
Configure Spanning Tree Protocol Commands 987
config spanningtree port mode 988
config spanningtree port pathcost 989
config spanningtree port priority 990
config spanningtree switch bridgepriority 991
config spanningtree switch forwarddelay 992
config spanningtree switch hellotime 993
config spanningtree switch maxage 994
config spanningtree switch mode 995
Configure TACACS Commands 996
config tacacs acct 997
config tacacs athr 999
config tacacs athr mgmt-server-timeout 1001
config tacacs auth 1002
config tacacs auth mgmt-server-timeout 1004
Configure Trap Flag Commands 1005
config trapflags 802.11-Security 1006
config trapflags aaa 1007
config trapflags ap 1008
config trapflags authentication 1009
config trapflags client 1010
config trapflags configsave 1011
config trapflags IPsec 1012
config trapflags linkmode 1013
config trapflags multiusers 1014
config trapflags rogueap 1015
config trapflags rrm-params 1016
config trapflags rrm-profile 1017
config trapflags stpmode 1018
config trapflags wps 1019
Configure Watchlist Commands 1020
config watchlist add 1021
config watchlist delete 1022
config watchlist disable 1023
Cisco Wireless LAN Controller Command Reference, Release 7.3 OL-27543-01 xxvii
Contents
-
config watchlist enable 1024
Configure Wireless LAN Commands 1025
config wlan 1026
config wlan 7920-support 1028
config wlan 802.11e 1029
config wlan aaa-override 1030
config wlan acl 1031
config wlan apgroup 1032
config wlan band-select allow 1039
config wlan broadcast-ssid 1040
config wlan call-snoop 1041
config wlan chd 1042
config wlan ccx aironet-ie 1043
config wlan channel-scan defer-priority 1044
config wlan channel-scan defer-time 1045
config wlan dhcp_server 1046
config wlan diag-channel 1047
config wlan dtim 1048
config wlan exclusionlist 1049
config wlan flexconnect ap-auth 1050
config wlan flexconnect learn-ipaddr 1051
config wlan flexconnect local-switching 1052
config wlan flexconnect vlan-central-switching 1054
config wlan override-rate-limit 1055
config wlan interface 1057
config wlan ipv6 acl 1058
config wlan kts-cac 1059
config wlan ldap 1060
config wlan load-balance 1061
config wlan mac-filtering 1062
config wlan max-associated-clients 1063
config wlan max-radio-clients 1064
config wlan media-stream 1065
config wlan mfp 1066
config wlan mobility anchor 1067
Cisco Wireless LAN Controller Command Reference, Release 7.3xxviii OL-27543-01
Contents
-
config wlan mobility foreign-map 1068
config wlan multicast buffer 1069
config wlan multicast interface 1070
config wlan nac 1071
config wlan passive-client 1072
config wlan peer-blocking 1073
config wlan profiling 1074
config wlan qos 1076
config wlan radio 1077
config wlan radius_server acct 1078
config wlan radius_server acct interim-update 1079
config wlan radius_server auth 1080
config wlan radius_server acct interim-update 1081
config wlan radius_server overwrite-interface 1082
config wlan roamed-voice-client re-anchor 1083
config wlan sip-cac disassoc-client 1084
config wlan sip-cac send-486busy 1085
config wlan static-ip tunneling 1086
config wlan session-timeout 1087
config wlan user-idle-threshold 1088
config wlan usertimeout 1089
config wlan webauth-exclude 1090
config wlan wmm 1091
Configure Wireless LAN HotSpot Commands 1091
config wlan hotspot 1092
config wlan hotspot dot11u 1093
config wlan hotspot dot11u 3gpp-info 1094
config wlan hotspot dot11u auth-type 1095
config wlan hotspot dot11u disable 1096
config wlan hotspot dot11u domain 1097
config wlan hotspot dot11u enable 1098
config wlan hotspot dot11u hessid 1099
config wlan hotspot dot11u ipaddr-type 1100
config wlan hotspot dot11u nai-realm 1101
config wlan hotspot dot11u network-type 1104
Cisco Wireless LAN Controller Command Reference, Release 7.3 OL-27543-01 xxix
Contents
-
config wlan hotspot dot11u roam-oi 1105
config wlan hotspot hs2 1106
config wlan hotspot msap 1109
Configure Wireless LAN Security Commands 1110
config wlan security 802.1X 1111
config wlan security ckip 1113
config wlan security cond-web-redir 1115
config wlan security eap-passthru 1116
config wlan security ft 1117
config wlan security ft over-the-ds 1118
config wlan security IPsec disable 1119
config wlan security IPsec enable 1120
config wlan security IPsec authentication 1121
config wlan security IPsec encryption 1122
config wlan security IPsec config 1123
config wlan security IPsec ike authentication 1124
config wlan security IPsec ike dh-group 1125
config wlan security IPsec ike lifetime 1126
config wlan security IPsec ike phase1 1127
config wlan security IPsec ike contivity 1128
config wlan security passthru 1129
config wlan security splash-page-web-redir 1130
config wlan security static-wep-key authentication 1131
config wlan security static-wep-key disable 1132
config wlan security static-wep-key enable 1133
config wlan security static-wep-key encryption 1134
config wlan security web-auth 1135
config wlan security web-passthrough acl 1137
config wlan security web-passthrough disable 1138
config wlan security web-passthrough email-input 1139
config wlan security web-passthrough enable 1140
config wlan security wpa akm 802.1x 1141
config wlan security wpa akm cckm 1142
config wlan security wpa akm ft 1143
config wlan security wpa akm psk 1144
Cisco Wireless LAN Controller Command Reference, Release 7.3xxx OL-27543-01
Contents
-
config wlan security wpa disable 1145
config wlan security wpa enable 1146
config wlan security wpa ciphers 1147
config wlan security wpa gtk-random 1148
config wlan security wpa wpa1 disable 1149
config wlan security wpa wpa1 enable 1150
config wlan security wpa wpa2 disable 1151
config wlan security wpa wpa2 enable 1152
config wlan security wpa wpa2 cache sticky 1153
Configure Wireless LAN Proxy Mobility IPv6 (PMIPv6) Commands 1153
config wlan pmipv6 default-realm 1154
config wlan pmipv6 mobility-type 1155
config wlan pmipv6 profile_name 1156
Configure WPS Commands 1157
config wps ap-authentication 1158
config wps auto-immune 1159
config wps cids-sensor 1160
config wps client-exclusion 1162
config wps client-exclusion 802.1x-auth 1164
config wps mfp 1165
config wps shun-list re-sync 1166
config wps signature 1167
config wps signature frequency 1169
config wps signature interval 1170
config wps signature mac-frequency 1171
config wps signature quiet-time 1172
config wps signature reset 1173
Other Config Commands 1173
config aaa auth 1174
config aaa auth mgmt 1175
config acl apply 1176
config acl counter 1177
config acl create 1178
config acl cpu 1179
config acl delete 1180
Cisco Wireless LAN Controller Command Reference, Release 7.3 OL-27543-01 xxxi
Contents
-
config acl rule 1181
config auth-list add 1183
config auth-list ap-policy 1184
config auth-list delete 1185
config boot 1186
config cdp 1187
config certificate 1188
config certificate lsc 1189
config certificate ssc 1191
config certificate use-device-certificate webadmin 1193
config coredump 1194
config coredump ftp 1195
config coredump username 1196
config country 1197
config cts sxp 1198
config cts sxp connection 1200
Other Config Commands 1200
config cts sxp default password 1201
config cts sxp retry period 1202
config custom-web ext-webauth-mode 1203
config custom-web ext-webauth-url 1204
config custom-web ext-webserver 1205
config custom-web logout-popup 1206
config custom-web redirectUrl 1207
config custom-web webauth-type 1208
config custom-web weblogo 1209
config custom-web webmessage 1210
config custom-web webtitle 1211
config database size 1212
config dhcp 1213
config dhcp proxy 1215
config dhcp timeout 1216
config exclusionlist 1217
config flexconnect acl 1218
config flexconnect acl rule 1219
Cisco Wireless LAN Controller Command Reference, Release 7.3xxxii OL-27543-01
Contents
-
config flexconnect group 1221
config flexconnect group vlan 1226
config flexconnect group web-auth 1227
config flexconnect group web-policy 1228
config flexconnect join min-latency 1229
config flexconnect office-extend 1230
config interface acl 1232
config interface address 1233
config interface ap-manager 1235
config interface create 1236
config interface delete 1237
config interface dhcp 1238
config interface address 1240
config interface guest-lan 1242
config interface hostname 1243
config interface nat-address 1244
config interface port 1245
config interface quarantine vlan 1246
config interface vlan 1247
config known ap 1248
config lag 1249
config ldap 1250
config ldap add 1252
config ldap simple-bind 1253
config license agent 1254
config license boot 1256
config load-balancing 1258
config local-auth active-timeout 1259
config local-auth eap-profile 1260
config local-auth method fast 1263
config local-auth user-credentials 1265
config location 1266
config logging buffered 1268
config logging console 1269
config logging debug 1270
Cisco Wireless LAN Controller Command Reference, Release 7.3 OL-27543-01 xxxiii
Contents
-
config logging fileinfo 1271
config logging procinfo 1272
config logging traceinfo 1273
config logging syslog host 1274
config logging syslog facility 1277
config logging syslog level 1279
config loginsession close 1280
config lsc mesh 1281
config nmsp notify-interval measurement 1282
config paging 1283
config passwd-cleartext 1284
config prompt 1285
config rfid auto-timeout 1286
config rfid status 1287
config rfid timeout 1288
config route add 1289
config route delete 1290
config serial baudrate 1291
config serial timeout 1292
config service timestamps 1293
config sessions maxsessions 1294
config sessions timeout 1295
config slot 1296
config switchconfig boot-break 1297
config switchconfig fips-prerequisite 1298
config switchconfig strong-pwd 1299
config switchconfig flowcontrol 1301
config switchconfig mode 1302
config switchconfig secret-obfuscation 1303
config sysname 1304
config time manual 1305
config time ntp 1306
config time timezone 1309
config time timezone location 1310
config wgb vlan 1313
Cisco Wireless LAN Controller Command Reference, Release 7.3xxxiv OL-27543-01
Contents
-
capwap ap Commands 1314
capwap ap controller ip address 1315
capwap ap dot1x 1316
capwap ap hostname 1317
capwap ap ip address 1318
capwap ap ip default-gateway 1319
capwap ap log-server 1320
capwap ap primary-base 1321
capwap ap primed-timer 1322
capwap ap secondary-base 1323
capwap ap tertiary-base 1324
lwapp ap controller ip address 1325
Saving Configurations 1325
save config 1326
Clearing Configurations, Log files, and Other Actions 1326
clear acl counters 1327
clear ap config 1328
clear ap eventlog 1329
clear ap join stats 1330
clear arp 1331
clear client tsm 1332
clear config 1333
clear ext-webauth-url 1334
clear license agent 1335
clear location rfid 1336
clear location statistics rfid 1337
clear locp statistics 1338
clear login-banner 1339
clear lwapp private-config 1340
clear nmsp statistics 1341
clear radius acct statistics 1342
clear tacacs auth statistics 1343
clear redirect-url 1344
clear stats ap wlan 1345
clear stats local-auth 1346
Cisco Wireless LAN Controller Command Reference, Release 7.3 OL-27543-01 xxxv
Contents
-
clear stats mobility 1347
clear stats port 1348
clear stats radius 1349
clear stats switch 1351
clear stats tacacs 1352
clear transfer 1353
clear traplog 1354
clear webimage 1355
clear webmessage 1356
clear webtitle 1357
Resetting the System Reboot Time 1357
reset system at 1358
reset system in 1359
reset system cancel 1360
reset system notify-time 1361
reset peer-system 1362
test pmk-cache delete 1363
Uploading and Downloading Files and Configurations 1363
transfer download certpasswor 1364
transfer download datatype 1365
transfer download filename 1367
transfer download mode 1368
transfer download password 1369
transfer download path 1370
transfer download port 1371
transfer download serverip 1372
transfer download start 1373
transfer download tftpPktTimeout 1374
transfer download tftpMaxRetries 1375
transfer download username 1376
transfer encrypt 1377
transfer upload datatype 1378
transfer upload filename 1380
transfer upload mode 1381
transfer upload pac 1382
Cisco Wireless LAN Controller Command Reference, Release 7.3xxxvi OL-27543-01
Contents
-
transfer upload password 1383
transfer upload path 1384
transfer upload peer-start 1385
transfer upload port 1386
transfer upload serverip 1387
transfer upload start 1388
transfer upload username 1389
Installing and Modifying Licenses on Cisco 5500 Series Controllers 1389
license clear 1390
license comment 1391
license install 1392
license modify priority 1393
license revoke 1395
license save 1396
Right to Use Licensing Commands 1396
license activate ap-count eval 1397
license activate feature 1398
license add ap-count 1399
license add feature 1400
license deactivate ap-count eval 1401
license deactivate feature 1402
license delete ap-count 1403
license delete feature 1404
Integrated Management Module Commands in Cisco Flex 7500 Series Controllers 1404
imm address 1405
imm dhcp 1406
imm mode 1407
imm restart 1408
imm summary 1409
imm username 1410
Troubleshooting Commands 1410
debug aaa 1411
debug aaa local-auth 1412
debug airewave-director 1414
debug ap 1416
Cisco Wireless LAN Controller Command Reference, Release 7.3 OL-27543-01 xxxvii
Contents
-
debug ap enable 1417
debug ap packet-dump 1418
debug ap show stats 1419
debug ap show stats video 1421
debug arp 1422
debug bcast 1423
debug cac 1424
debug call-control 1425
debug capwap 1426
debug capwap reap 1427
debug client 1428
debug crypto 1429
debug dhcp 1430
debug dhcp service-port 1431
debug disable-all 1432
debug dot11 1433
debug dot11 mgmt interface 1435
debug dot11 mgmt msg 1436
debug dot11 mgmt ssid 1437
debug dot11 mgmt state-machine 1438
debug dot11 mgmt station 1439
debug dot1x 1440
debug group 1441
debug flexconnect aaa 1442
debug flexconnect acl 1443
debug flexconnect cckm 1444
debug flexconnect group 1445
debug hotspot 1446
debug hotspot packets 1447
debug l2age 1448
debug lwapp console cli 1449
debug mac 1450
debug media-stream 1451
debug memory 1452
debug mesh security 1453
Cisco Wireless LAN Controller Command Reference, Release 7.3xxxviii OL-27543-01
Contents
-
debug mobility 1454
debug nac 1456
debug nmsp 1457
debug ntp 1458
debug packet error 1459
debug packet logging 1460
debug pem 1463
debug pm 1464
debug poe 1466
debug profiling 1467
debug rbcp 1468
debug rfac 1469
debug rfid 1470
debug rmgr 1471
debug rsyncmgr 1472
debug service ap-monitor 1473
debug snmp 1474
debug transfer 1475
debug voice-diag 1476
debug web-auth 1477
debug wcp 1478
debug wps sig 1479
debug wps mfp 1480
eping 1481
mping 1482
Cisco Wireless LAN Controller Command Reference, Release 7.3 OL-27543-01 xxxix
Contents
-
Cisco Wireless LAN Controller Command Reference, Release 7.3xl OL-27543-01
Contents
-
Preface
This preface describes the audience, organization, and conventions of the Cisco Wireless LAN ControllerCommand Reference Guide. It also provides information on how to obtain other documentation. This chapterincludes the following sections:
Audience, page xli
Document Organization, page xli
Document Conventions, page xli
Related Documentation, page xliv
Obtaining Documentation and Submitting a Service Request, page xliv
AudienceThis publication is for experienced network administrators who configure and maintain Cisco wirelesscontrollers and Cisco lightweight access points.
Document OrganizationThis document is organized into the following chapters:
DescriptionChapter
Describes how to use the command-line interface (CLI) on the controller.Overview
Provides detailed information about the CLI commands for the controller.CLI Commands
Document ConventionsThis document uses the following conventions:
Cisco Wireless LAN Controller Command Reference, Release 7.3 OL-27543-01 xli
-
IndicationConvention
Commands and keywords and user-entered text appear in bold font.bold font
Document titles, new or emphasized terms, and arguments for which you supplyvalues are in italic font.
italic font
Elements in square brackets are optional.[ ]
Required alternative keywords are grouped in braces and separated by verticalbars.
{x | y | z }
Optional alternative keywords are grouped in brackets and separated by verticalbars.
[ x | y | z ]
A nonquoted set of characters. Do not use quotation marks around the string orthe string will include the quotation marks.
string
Terminal sessions and information the system displays appear in courier font.courier font
Nonprinting characters such as passwords are in angle brackets.
Default responses to system prompts are in square brackets.[]
An exclamation point (!) or a pound sign (#) at the beginning of a line of codeindicates a comment line.
!, #
Means reader take note. Notes contain helpful suggestions or references to material not covered in themanual.
Note
Means the following information will help you solve a problem.Tip
Means reader be careful. In this situation, you might perform an action that could result in equipmentdamage or loss of data.
Caution
This warning symbol means danger. You are in a situation that could cause bodily injury. Before youwork on any equipment, be aware of the hazards involved with electrical circuitry and be familiar withstandard practices for preventing accidents. (To see translations of the warnings that appear in thispublication, refer to the appendix "Translated Safety Warnings.")
Warning
Cisco Wireless LAN Controller Command Reference, Release 7.3xlii OL-27543-01
PrefaceDocument Conventions
-
DescriptionWarning Title
Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie dielichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken,dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico'sen dient u op de hoogte te zijn van standaard maatregelen om ongelukken tevoorkomen. (Voor vertalingen van de waarschuwingen die in deze publicatieverschijnen, kunt u het aanhangsel "Translated Safety Warnings" (Vertalingenvan veiligheidsvoorschriften) raadplegen.)
Waarschuwing
Tm varoitusmerkki merkitsee vaaraa. Olet tilanteessa, joka voi johtaaruumiinvammaan. Ennen kuin tyskentelet minkn laitteiston parissa, ota selvshkkytkentihin liittyvist vaaroista ja tavanomaisista onnettomuuksienehkisykeinoista. (Tss julkaisussa esiintyvien varoitusten knnkset lydtliitteest "Translated Safety Warnings" (knnetyt turvallisuutta koskevatvaroitukset).)
Varoitus
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans unesituation pouvant entraner des blessures. Avant d'accder cet quipement,soyez conscient des dangers poss par les circuits lectriques et familiarisez-vousavec les procdures courantes de prvention des accidents. Pour obtenir lestraductions des mises en garde figurant dans cette publication, veuillez consulterl'annexe intitule Translated SafetyWarnings (Traduction des avis de scurit).
Attention
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, diezu einer Krperverletzung fhren knnte. Bevor Siemit der Arbeit an irgendeinemGert beginnen, seien Sie sich der mit elektrischen Stromkreisen verbundenenGefahren und der Standardpraktiken zur Vermeidung von Unfllen bewut.(bersetzungen der in dieser Verffentlichung enthaltenenWarnhinweise findenSie im Anhang mit dem Titel "Translated Safety Warnings" (bersetzung derWarnhinweise).)
Warnung
Questo simbolo di avvertenza indica un pericolo. Si in una situazione che pucausare infortuni. Prima di lavorare su qualsiasi apparecchiatura, occorreconoscere i pericoli relativi ai circuiti elettrici ed essere al corrente delle pratichestandard per la prevenzione di incidenti. La traduzione delle avvertenze riportatein questa pubblicazione si trova nell'appendice, "Translated Safety Warnings"(Traduzione delle avvertenze di sicurezza).
Avvertenza
Dette varselsymbolet betyr fare. Du befinner deg i en situasjon som kan fre tilpersonskade. Fr du utfrer arbeid p utstyr, m du vre oppmerksom p defaremomentene som elektriske kretser innebrer, samt gjre deg kjent med vanligpraksis nr det gjelder unng ulykker. (Hvis du vil se oversettelser av deadvarslene som finnes i denne publikasjonen, kan du se i vedlegget "TranslatedSafety Warnings" [Oversatte sikkerhetsadvarsler].)
Advarsel
Este smbolo de aviso indica perigo. Encontra-se numa situao que lhe podercausar danos fisicos. Antes de comear a trabalhar com qualquer equipamento,familiarize-se com os perigos relacionados com circuitos elctricos, e comquaisquer prticas comuns que possam prevenir possveis acidentes. (Para veras tradues dos avisos que constam desta publicao, consulte o apndice"Translated Safety Warnings" - "Tradues dos Avisos de Segurana").
Aviso
Cisco Wireless LAN Controller Command Reference, Release 7.3 OL-27543-01 xliii
PrefaceDocument Conventions
-
DescriptionWarning Title
Este smbolo de aviso significa peligro. Existe riesgo para su integridad fsica.Antes de manipular cualquier equipo, considerar los riesgos que entraa lacorriente elctrica y familiarizarse con los procedimientos estndar de prevencinde accidentes. (Para ver traducciones de las advertencias que aparecen en estapublicacin, consultar el apndice titulado "Translated Safety Warnings.")
Advertencia!
Denna varningssymbol signalerar fara. Du befinner dig i en situation som kanleda till personskada. Innan du utfr arbete p ngon utrustning mste du varamedveten om farorna med elkretsar och knna till vanligt frfarande fr attfrebygga skador. (Se frklaringar av de varningar som frekommer i dennapublikation i appendix "Translated Safety Warnings" [versattaskerhetsvarningar].)
Varning
Related DocumentationThese documents provide complete information about the Cisco Unified Wireless Network solution:
Cisco Wireless LAN Controller Configuration Guide
Cisco Wireless LAN Controller System Message Guide
Release Notes for Cisco Wireless LAN Controllers and Lightweight Access Points
Obtaining Documentation and Submitting a Service RequestFor information about obtaining documentation, submitting a service request, and gathering additionalinformation, see the monthlyWhat's New in Cisco Product Documentation, which also lists all new and revisedCisco technical documentation, at:
http://www.cisco.com/c/en/us/td/docs/general/whatsnew/whatsnew.html
Subscribe to theWhat's New in Cisco Product Documentation as an RSS feed and set content to be delivereddirectly to your desktop using a reader application. The RSS feeds are a free service. Cisco currently supportsRSS Version 2.0.
Cisco Wireless LAN Controller Command Reference, Release 7.3xliv OL-27543-01
PrefaceRelated Documentation
-
Using the Command-Line Interface
This chapter contains the following topics:
CLI Command Keyboard Shortcuts, page 1
Using the Interactive Help Feature, page 2
CLI Command Keyboard ShortcutsThe table below lists the CLI keyboard shortcuts to help you enter and edit command lines on the controller.
Table 1: CLI Command Keyboard Shortcuts
Keyboard ShortcutDescriptionAction
Esc IThe word at the cursor to lowercase.Change
Esc uThe word at the cursor to uppercase.
Ctrl-h, Delete, or BackspaceA character to the left of the cursor.Delete
Ctrl-uAll characters from the cursor to the beginning of theline.
Ctrl-kAll characters from the cursor to the end of the line.
Esc dAll characters from the cursor to the end of the word.
Ctrl-w or Esc BackspaceThe word to the left of the cursor.
q, Q, or Ctrl-CExit from MORE output.Display MOREoutput
SpacebarNext additional screen. The default is one screen. Todisplay more than one screen, enter a number beforepressing the Spacebar key.
Cisco Wireless LAN Controller Command Reference, Release 7.3 OL-27543-01 1
-
Keyboard ShortcutDescriptionAction
EnterNext line. The default is one line. To display more thanone line, enter the number before pressing the Enterkey.
Ctrl-mEnter an Enter or Return key character.
Ctrl-t or TabExpand the command or abbreviation.
Ctrl-b or Left ArrowOne character to the left (back).Move the cursor
Ctrl-f or Right ArrowOne character to the right (forward).
Esc bOne word to the left (back), to the beginning of thecurrent or previous word.
Esc fOne word to the right (forward), to the end of thecurrent or next word.
Ctrl-aTo the beginning of the line.
Ctrl-eTo the end of the line.
Ctrl-l or Ctrl-rRedraw the screen at the prompt.
Ctrl-zReturn to the EXEC mode from any configuration mode
exit commandReturn to the previous mode or exit from the CLI from Exec mode.
Ctrl-tTranspose a character at the cursor with a character to the left of the cursor.
Using the Interactive Help FeatureThe question mark (?) character allows you to get the following type of help about the command at thecommand line. The table below lists the interactive help feature list.
Table 2: Interactive Help Feature List
Command
Provides a brief description of the Help feature in any command mode.help
Lists all commands available for a particular command mode.? at the commandprompt
Provides a list of commands that begin with the character string.partial command?
Cisco Wireless LAN Controller Command Reference, Release 7.32 OL-27543-01
Using the Command-Line InterfaceUsing the Interactive Help Feature
-
Command
Completes a partial command name.partialcommand
Lists the keywords, arguments, or both associated with a command.command ?
Lists the arguments that are associated with the keyword.command keyword ?
Using the help Command
Before You Begin
To look up keyboard commands, use the help command at the root level.
help
Help may be requested at any point in a command by entering a question mark ?. If nothing matches, thehelp list will be empty and you must back up until entering a ? shows the available options. Two types ofhelp are available:
1 Full help is available when you are ready to enter a command argument (for example show ?) and describeseach possible argument.
2 Partial help is provided when an abbreviated argument is entered and you want to know what argumentsmatch the input (for example show pr?).
Example:
> helpHELP:Special keys:DEL, BS... delete previous characterCtrl-A .... go to beginning of lineCtrl-E .... go to end of lineCtrl-F .... go forward one characterCtrl-B .... go backward one characterCtrl-D .... delete current characterCtrl-U, X. delete to beginning of lineCtrl-K .... delete to end of lineCtrl-W .... delete previous wordCtrl-T .... transpose previous characterCtrl-P .... go to previous line in history bufferCtrl-N .... go to next line in history bufferCtrl-Z .... return to root command promptTab, command-line completionExit .... go to next lower command prompt? .... list choices
Using the ? command
Before You Begin
To display all of the commands in your current level of the command tree, or to display more informationabout a particular command, use the ? command.
Cisco Wireless LAN Controller Command Reference, Release 7.3 OL-27543-01 3
Using the Command-Line InterfaceUsing the help Command
-
command name ?
When you enter a command information request, put a space between the command name and ?.
Examples This command shows you all the commands and levels available from the root level.
> ?clear Clear selected configuration elements.config Configure switch options and settings.debug Manages system debug options.help Helplinktest Perform a link test to a specified MAC address.logout Exit this session. Any unsaved changes are lost.ping Send ICMP echo packets to a specified IP address.reset Reset options.save Save switch configurations.show Display switch options and settings.transfer Transfer a file to or from the switch.
Using the partial? command
Before You Begin
To provide a list of commands that begin with the character string, use the partial command ?.
partial command?
There should be no space between the command and the question mark.
This example shows how to provide a command that begin with the character string ad:
> controller> config>ad?
The command that matches with the string ad is as follows:
advanced
Using the partial command
Before You Begin
To completes a partial command name, use the partial command command.
partial command
There should be no space between the command and .
This example shows how to complete a partial command name that begin with the character string ad:
Controller >config>cert certificate
Cisco Wireless LAN Controller Command Reference, Release 7.34 OL-27543-01
Using the Command-Line InterfaceUsing the partial? command
-
Using the command ?
Examples To list the keywords, arguments, or both associated with the command, use the command ?.command-name ?
There should be a space between the command and the question mark.
This example shows how to list the arguments and keyword for the command acl:
Controller >config acl ?
Information similar to the following appears:
apply Applies the ACL to the data path.counter Start/Stop the ACL Counters.create Create a new ACL.delete Delete an ACL.rule Configure rules in the ACL.cpu Configure the CPU Acl Information
Cisco Wireless LAN Controller Command Reference, Release 7.3 OL-27543-01 5
Using the Command-Line InterfaceUsing the command ?
-
command keyword ?To list the arguments that are associated with the keyword, use the command keyword ?:
command keyword ?
There should be space between the keyword and the question mark.
This example shows how to display the arguments associated with the keyword cpu:
Controller >config acl cpu ?
Information similar to the following appears:
none None - Disable the CPU ACL - Name of the CPU ACL
Cisco Wireless LAN Controller Command Reference, Release 7.36 OL-27543-01
Using the Command-Line Interfacecommand keyword ?
-
CLI Commands
CLI Commands, page 8
Cisco Wireless LAN Controller Command Reference, Release 7.3 OL-27543-01 7
-
CLI CommandsThe Cisco Wireless LAN solution command-line interface (CLI) enables operators to connect an ASCIIconsole to the Cisco Wireless LAN Controller (Cisco WLC) and configure the Cisco WLC and its associatedaccess points.
Cisco Wireless LAN Controller Command Reference, Release 7.38 OL-27543-01
CLI CommandsCLI Commands
-
Show CommandsUse the show commands to display information about your configuration settings.
Cisco Wireless LAN Controller Command Reference, Release 7.3 OL-27543-01 9
CLI CommandsShow Commands
-
show 802.11To display basic 802.11a, 802.11b/g, or 802.11h network settings, use the show 802.11 command.
show 802.11{a | b | h}
Syntax Description Specifies the 802.11a network.a
Specifies the 802.11b/g network.b
Specifies the 802.11h network.h
Command Default None.
Examples This example shows to display basic 802.11a network settings:
> show 802.11a802.11a Network.................................. Enabled11nSupport....................................... Enabled
802.11a Low Band........................... Enabled802.11a Mid Band........................... Enabled802.11a High Band.......................... Enabled
802.11a Operational Rates802.11a 6M Rate.............................. Mandatory802.11a 9M Rate.............................. Supported802.11a 12M Rate............................. Mandatory802.11a 18M Rate............................. Supported802.11a 24M Rate............................. Mandatory802.11a 36M Rate............................. Supported802.11a 48M Rate............................. Supported802.11a 54M Rate............................. Supported
802.11n MCS Settings:MCS 0........................................ SupportedMCS 1........................................ SupportedMCS 2........................................ SupportedMCS 3........................................ SupportedMCS 4........................................ SupportedMCS 5........................................ SupportedMCS 6........................................ SupportedMCS 7........................................ SupportedMCS 8........................................ SupportedMCS 9........................................ SupportedMCS 10....................................... SupportedMCS 11....................................... SupportedMCS 12....................................... SupportedMCS 13....................................... SupportedMCS 14....................................... SupportedMCS 15....................................... Supported
802.11n Status:A-MPDU Tx:
Priority 0............................... EnabledPriority 1............................... DisabledPriority 2............................... DisabledPriority 3............................... DisabledPriority 4............................... DisabledPriority 5............................... DisabledPriority 6............................... DisabledPriority 7............................... Disabled
Cisco Wireless LAN Controller Command Reference, Release 7.310 OL-27543-01
CLI CommandsShow Commands
-
Beacon Interval.................................. 100CF Pollable mandatory............................ DisabledCF Poll Request mandatory........................ Disabled--More-- or (q)uitCFP Period....................................... 4CFP Maximum Duration............................. 60Default Channel.................................. 36Default Tx Power Level........................... 0DTPC Status..................................... EnabledFragmentation Threshold.......................... 2346TI Threshold..................................... -50Legacy Tx Beamforming setting.................... DisabledTraffic Stream Metrics Status.................... EnabledExpedited BW Request Status...................... DisabledWorld Mode....................................... EnabledEDCA profile type................................ default-wmmVoice MAC optimization status.................... DisabledCall Admission Control (CAC) configurationVoice AC:
Voice AC - Admission control (ACM)............ DisabledVoice max RF bandwidth........................ 75Voice reserved roaming bandwidth.............. 6Voice load-based CAC mode..................... DisabledVoice tspec inactivity timeout................ DisabledVoice Stream-Size............................. 84000Voice Max-Streams............................. 2
Video AC:Video AC - Admission control (ACM)............ DisabledVideo max RF bandwidth........................ InfiniteVideo reserved roaming bandwidth.............. 0
This example shows how to display basic 802.11h network settings:
> show 802.11h802.11h ......................................... powerconstraint : 0802.11h ......................................... channelswitch : Disable802.11h ......................................... channelswitch mode : 0
Related Commands show ap stats
show ap summary
show client summary
show network
show network summary
show port
show wlan
Cisco Wireless LAN Controller Command Reference, Release 7.3 OL-27543-01 11
CLI CommandsShow Commands
-
show 802.11 cleanairTo display the multicast-direct configuration state, use the show 802.11 cleanair command.
show 802.11{a | b | h} cleanair config
Syntax Description Specifies the 802.11a network.a
Specifies the 802.11b/g network.b
Specifies the 802.11h network.h
Displays the network Cleanair configuration.config
Command Default None
Command History ModificationRelease
This commandwas introduced in a release earlier thanRelease 7.6.
7.6
Examples The following example shows how to display the 802.11a cleanair configuration:
(Cisco Controller) > show 802.11a cleanairClean Air Solution............................... EnabledAir Quality Settings:
Air Quality Reporting........................ EnabledAir Quality Reporting Period (min)........... 15Air Quality Alarms........................... EnabledAir Quality Alarm Threshold.................. 35 Interference Device
Settings:Interference Device Reporting................ EnabledInterference Device Types:
TDD Transmitter.......................... DisabledJammer................................... DisabledContinuous Transmitter................... DisabledDECT-like Phone.......................... DisabledVideo Camera............................. DisabledWiFi Inverted............................ DisabledWiFi Invalid Channel..................... DisabledSuperAG.................................. DisabledRadar.................................... DisabledCanopy................................... DisabledWiMax Mobile............................. DisabledWiMax Fixed.............................. Disabled
Interference Device Alarms................... EnabledInterference Device Types Triggering Alarms:
TDD Transmitter.......................... Disabled
Cisco Wireless LAN Controller Command Reference, Release 7.312 OL-27543-01
CLI CommandsShow Commands
-
Jammer................................... DisabledContinuous Transmitter................... DisabledDECT-like Phone.......................... DisabledVideo Camera............................. DisabledWiFi Inverted............................ DisabledWiFi Invalid Channel..................... DisabledSuperAG.................................. DisabledRadar.................................... DisabledCanopy................................... DisabledWiMax Mobile............................. DisabledWiMax Fixed.............................. Disabled Additional
Clean Air Settings:CleanAir Event-driven RRM State.............. EnabledCleanAir Driven RRM Sensitivity.............. MediumCleanAir Persistent Devices state............ Disabled
Cisco Wireless LAN Controller Command Reference, Release 7.3 OL-27543-01 13
CLI CommandsShow Commands
-
show 802.11 cleanair air-quality summaryTo display the air quality summary information for the 802.11 networks, use the show 802.11 cleanairair-quality summary command.
show 802.11 {a | b | h} cleanair air-quality summary
Syntax Description Specifies the 802.11a network.a
Specifies the 802.11b/g network.b
Specifies the 802.11h network.h
Displays a summary of 802.11 radio band air qualityinformation.
summary
Command Default None
Command History ModificationRelease
This commandwas introduced in a release earlier thanRelease 7.6.
7.6
Examples The following example shows how to display a summary of the air quality information for the 802.11a network:
(Cisco Controller) > show 802.11a cleanair air-quality summaryAQ = Air QualityDFS = Dynamic Frequency SelectionAP Name Channel Avg AQ Min AQ Interferers DFS------------------ ------- ------ ------ ----------- ---CISCO_AP3500 36 95 70 0CISCO_AP3500 40 93 75 0
Cisco Wireless LAN Controller Command Reference, Release 7.314 OL-27543-01
CLI CommandsShow Commands
-
show 802.11 cleanair air-quality worstTo display the worst air quality information for the 802.11 networks, use the show 802.11 cleanair air-qualityworst command.
show 802.11{a | b | h} cleanair air-quality worst
Syntax Description Specifies the 802.11a network.a
Specifies the 802.11b/g network.b
Specifies the 802.11h network.h
Displays the worst air quality information for 802.11networks.
worst
Command Default None
Command History ModificationRelease
This commandwas introduced in a release earlier thanRelease 7.6.
7.6
Examples The following example shows how to display worst air quality information for the 802.11a network:
(Cisco Controller) > show 802.11 cleanair air-quality worstAQ = Air QualityDFS = Dynamic Frequency SelectionAP Name Channel Avg AQ Min AQ Interferers DFS------------------ ------- ------ ------ ----------- ---CISCO_AP3500 1 83 57 3 5
Cisco Wireless LAN Controller Command Reference, Release 7.3 OL-27543-01 15
CLI CommandsShow Commands
-
show 802.11 cleanair device apTo display the information of the device access point on the 802.11 radio band, use the show 802.11 cleanairdevice ap command.
show 802.11 {a | b | h} cleanair device ap cisco_ap
Syntax Description Specifies the 802.11a network.a
Specifies the 802.11b/g network.b
Specifies the 802.11h network.h
Specified access point name.cisco_ap
Command Default None
Command History ModificationRelease
This commandwas introduced in a release earlier thanRelease 7.6.
7.6
Examples The following example shows how to display the device access point for the 802.11a network:(Cisco Controller) > show 802.11a cleanair device ap AP_3500DC = Duty Cycle (%)ISI = Interference Severity Index (1-Low Interference, 100-HighInterference)RSSI = Received Signal Strength Index (dBm)DevID = Device IDNo ClusterID DevID Type AP Name ISIRSSI DC Channel--- ------------------ ------ ---------- --------------- ---- ----- -----------------1 c2:f7:40:00:00:03 0x8001 DECT phone CISCO_AP3500 1 -43 3
149,153,157,1612 c2:f7:40:00:00:51 0x8002 Radar CISCO_AP3500 1 -81 2153,157,161,165
3 c2:f7:40:00:00:03 0x8005 Canopy CISCO_AP3500 2 -62 2153,157,161,165
Cisco Wireless LAN Controller Command Reference, Release 7.316 OL-27543-01
CLI CommandsShow Commands
-
show 802.11 cleanair device typeTo display the information of all the interferers device type detected by a specific access point on the 802.11radio band, use the show 802.11 cleanair device type command.
show 802.11{a | b | h} cleanair device type device_type
Syntax Description Specifies the 802.11a network.a
Specifies the 802.11b/g network.b
Specifies the 802.11h network.h
Interferer device type for a specified radio band. Thedevice type is one of the following:
tdd-txTdd-transmitter device information.
jammerJammer device information.
cont-txContinuous-transmitter devicesinformation.
dect-likeDect-like phone devices information.
videoVideo devices information.
802.11-invWiFi inverted devices information.
802.11-nonstdNonstandard WiFi devicesinformation.
superagSuperag devices information.
canopyCanopy devices information.
wimax-mobileWiMax mobile devicesinformation.
wimax-fixedWiMax fixed devicesinformation.
device_type
Command Default None
Command History ModificationRelease
This commandwas introduced in a release earlier thanRelease 7.6.
7.6
Cisco Wireless LAN Controller Command Reference, Release 7.3 OL-27543-01 17
CLI CommandsShow Commands
-
Examples The following example shows how to display the information of all the interferers detected by a specifiedaccess point for the 802.11a network:
(Cisco Controller) > show 802.11a cleanair device type canopyDC = Duty Cycle (%)ISI = Interference Severity Index (1-Low Interference, 100-HighInterference)RSSI = Received Signal Strength Index (dBm)DevID = Device IDNo ClusterID DevID Type AP Name ISIRSSI DC Channel--- ------------------ ------ ---------- --------------- ---- ----- -----------------1c2:f7:40:00:00:03 0x8005 Canopy CISCO_AP3500 2 -62 2
153,157,161,165
Cisco Wireless LAN Controller Command Reference, Release 7.318 OL-27543-01
CLI CommandsShow Commands
-
show 802.11 cu-metricsTo display access point channel utilization metrics, use the show 802.11 cu-metrics command.
show 802.11{a | b} cu-metrics cisco_ap
Syntax Description Specifies the 802.11a network.a
Specifies the 802.11b/g network.b
Access point name.cisco_ap
Command Default None
Command History ModificationRelease
This command was introduced in a release earlier than Release 7.6.7.6
Examples The following is a sample output of the show 802.11a cu-metrics command:
(Cisco Controller) > show 802.11a cu-metrics AP1AP Interface Mac: 30:37:a6:c8:8a:50Measurement Duration: 90secTimestamp Thu Jan 27 09:08:48 2011Channel Utilization stats================Picc (50th Percentile)...................... 0Pib (50th Percentile)....................... 76Picc (90th Percentile)...................... 0Pib (90th Percentile)....................... 77
Timestamp Thu Jan 27 09:34:34 2011
Cisco Wireless LAN Controller Command Reference, Release 7.3 OL-27543-01 19
CLI CommandsShow Commands
-
show 802.11 extendedTo display access point radio extended configurations, use the show 802.11 extended command.
show 802.11 {a | b} extended
Syntax Description Specifies the 802.11a network.a
Specifies the 802.11b/g network.b
Displays the 802.11a/b radio extended configurations.extended
Command Default None
Command History ModificationRelease
This commandwas introduced in a release earlier thanRelease 7.6.
7.6
Examples The following example shows how to display radio extended configurations:
(Cisco Controller) > show 802.11a extendedDefault 802.11a band radio extended configurations:
beacon period 300, range 60;multicast buffer 45, rate 200;RX SOP -80; CCA threshold -90;
AP0022.9090.b618 00:24:97:88:99:60beacon period 300, range 60; multicast buffer 45, rate 200;RX SOP -80; CCA threshold -77
AP0022.9090.bb3e 00:24:97:88:c5:d0beacon period 300, range 0; multicast buffer 0, rate 0;RX SOP -80; CCA threshold -0
ironRap.ddbf 00:17:df:36:dd:b0beacon period 300, range 0; multicast buffer 0, rate 0;RX SOP -80; CCA threshold -0
Cisco Wireless LAN Controller Command Reference, Release 7.320 OL-27543-01
CLI CommandsShow Commands
-
show 802.11 media-streamTo display the multicast-direct configuration state, use the show 802.11 media-stream command.
show 802.11 {a | b | h}media-stream media_stream_name
Syntax Description Specifies the 802.11a network.a
Specifies the 802.11b/g network.b
Specifies the 802.11h network.h
Specified media stream name.media_stream_name
Command Default None.
Examples This example shows how to display the media-stream configuration:
> show 802.11a media-stream rrcMulticast-direct................................. EnabledBest Effort...................................... DisabledVideo Re-Direct.................................. EnabledMax Allowed Streams Per Radio.................... AutoMax Allowed Streams Per Client................... AutoMax Video Bandwidth.............................. 0Max Voice Bandwidth.............................. 75Max Media Bandwidth.............................. 85Min PHY Rate..................................... 6000Max Retry Percentage............................. 80
Related Commands show media-stream group summary
Cisco Wireless LAN Controller Command Reference, Release 7.3 OL-27543-01 21
CLI CommandsShow Commands
-
Show Advanced CommandsUse the show advanced commands to display more detailed information.
Cisco Wireless LAN Controller Command Reference, Release 7.322 OL-27543-01
CLI CommandsShow Advanced Commands
-
show advanced 802.11 channelTo display the automatic channel assignment configuration and statistics, use the show advanced 802.11channel command.
show advanced 802.11{a | b} channel
Syntax Description Specifies the 802.11a network.a
Specifies the 802.11b/g network.b
Command Default None
Command History ModificationRelease
This commandwas introduced in a release earlier thanRelease 7.6.
7.6
Examples The following example shows how to display the automatic channel assignment configuration and statistics:
(Cisco Controller) > show advanced 802.11a channelAutomatic Channel AssignmentChannel Assignment Mode........................ AUTOChannel Update Interval........................ 600 seconds [startup]Anchor time (Hour of the day).................. 0Channel Update Contribution.................... SNI.Channel Assignment Leader...................... 00:1a:6d:dd:1e:40Last Run....................................... 129 seconds agoDCA Sensitivity Level: ...................... STARTUP (5 dB)DCA Minimum Energy Limit....................... -95 dBm
Channel Energy LevelsMinimum...................................... unknownAverage...................................... unknownMaximum...................................... unknown
Channel Dwell TimesMinimum...................................... unknownAverage...................................... unknownMaximum...................................... unknown
Auto-RF Allowed Channel List...................36,40,44,48,52,56,60,64,149,
............................................. 153,157,161Auto-RF Unused Channel List....................
100,104,108,112,116,132,136,............................................. 140,165,190,196
DCA Outdoor AP option.......................... Enabled
Cisco Wireless LAN Controller Command Reference, Release 7.3 OL-27543-01 23
CLI CommandsShow Advanced Commands
-
show advanced 802.11 coverageTo display the configuration and statistics for coverage hole detection, use the show advanced 802.11 coveragecommand.
show advanced 802.11{a | b} co