Disclosure to Promote the Right To Information

Whereas the Parliament of India has set out to provide a practical regime of right to information for citizens to secure access to information under the control of public authorities, in order to promote transparency and accountability in the working of every public authority, and whereas the attached publication of the Bureau of Indian Standards is of particular interest to the public, particularly disadvantaged communities and those engaged in the pursuit of education and knowledge, the attached public safety standard is made available to promote the timely dissemination of this information in an accurate manner to the public.

इंटरनेट मानक

“!ान $ एक न' भारत का +नम-ण”Satyanarayan Gangaram Pitroda

“Invent a New India Using Knowledge”

“प0रा1 को छोड न' 5 तरफ”Jawaharlal Nehru

“Step Out From the Old to the New”

“जान1 का अ+धकार, जी1 का अ+धकार”Mazdoor Kisan Shakti Sangathan

“The Right to Information, The Right to Live”

“!ान एक ऐसा खजाना > जो कभी च0राया नहB जा सकता है”Bhartṛhari—Nītiśatakam

“Knowledge is such a treasure which cannot be stolen”

“Invent a New India Using Knowledge”

है”ह”ह

IS 11114-3 (2006): Earth-moving machinery - Definitions ofdimensions and codes, Part 3: Equipment and attachments[MED 7: Material Handling Systems and Equipment]

IS 11114 (Part 3) :2006ISO 6746-2:2003

Indian Standard

EARTH-MOVING MACHINERY —DEFINITIONS OF DIMENSIONS AND CODES

PART 3

(

EQUIPMENT AND ATTACHMENTS

Second Revision )

Ics 53.100

0 BIS 2006

BUREAU OF INDIAN STANDARDSMANAK BHAVAN, 9 BAHADUR SHAH ZAFAR MARG

NEW DELHI 110002

~U/y 2006 Prim Group 7

Material Handling System-s and Equipment Sectional Committee, ME 07

NATIONAL FOREWORD

This Indian Standard (Part 3) (Second Revision) which is identical with 1S0 6746-2:2003 ‘Earth-movingmachinery — Definitions of dimensions and codes — Part 2: Equipment and attachments’ issued by_the International Organization for Standardization (ISO) was adopted by the Bureau of Indian Standardson the recommendation of the Material Handling Systems and Equipment Sectional Committee andapproval of the Mechanical Engineering Division Council.

This standard was first published in 1985. In the-first revision ISO 6746-2:1987 was adopted. Presentrevision has been taken up to harmonize it with the latest version of ISO Standard.

The text of the ISO Standard has been approved as suitable for publication as an Indian Standardwithout deviations. Certain conventions are, however, not identical to those used in Indian Standards.Attention is particularly drawn to the following:

a) Wherever the words ‘International Standard’ appear referring to this standard, they shouldbe read as ‘Indian Standard’.

b) Comma (,) has been used as a decimal marker while in Indian Standards, tie current practiceis to use a point (.) as the decimal marker.

In this adopted standard, reference appears to certain International Standards for which Indian Standardsalso exist. The corresponding Indian Standards which are to be substituted in their places are listedbelow along with their degree of equivalence for the editions indicated:

International Standard Corresponding Indian Standard Degree ofEquivalence

ISO 6165 : 1987 Earth-moving IS 12138:1993 Earth-moving machinery Identical

machinery — Basic types — — Basic types —Vocabulary (first revision)Vocabulary

ISO 6746-1 :2003 Earth-moving IS 11114 (Part 2) :2006 Earth-moving domachinery — Definitions of machinery— Definitions of dimensions and

dimensions and codes — Part 1: codes: Part 2 Base machine (second

Base machine revision)

For the purpose of deciding whether a particular requirement of this standard iscomplied with, the finalvalue, observed or calculated, expressing the result of a test or analysis,”shall be rounded off in accordancewith IS 2 : 1960 ‘Rules for rounding off numerical values (revised’. The number of significant placesretained in the rounded off value should be the same as that of the specified value in this standard.

IS 11114 (Part3) : 20~6ISO 6746-2:2003

1 Scope

Indian Standard

EARTH-MOVING MACHINERY —DEFINITIONS OF DIMENSIONS AND CODES

PART 3 EQUIPMENT AND ATTACHMENTS

( Second Revision)

This part of ISO 6746 specifies a reference systemfor defining, and a coding system for identifying,equipment and attachment dimensions for earth-moving machinery in terminology standards andcommercial specifications.

It is applicable to the equipment and attachments ofbasic types of earth-moving machinery as defined inISO 6165.

2 Normative references

The following referenced documents are indispens-able for the application of this document. For datedreferences, only the edition cited applies. For un-dated references, the latest edition of the refer-enced document (imluding any amendments)applies.

ISO 6165, Earth-moving machjnery — Basictypes — Vocabulary

1 Domaine d’application

La presente partie de I’ISO 6746 specifie un sys-teme de reference pour definir Ies dimensions desequipments et des accessoires des engins de ter-rassement, clans Ies normes terminologiques etclans Ies specifications commercials, et un sys-teme de codage pour identifier ces dimensions.

Elte est applicable aux equipments et accessoiresdes principaux types d’engins de terrassement telsqu’ils sent definis clans I’ISO 6165.

2 References normative

Les documents de reference suivants sent indis-pensables pour I’application du present document.Pour Ies references datees, seule I’edition citees’applique. Pour Ies references non datees, la der-niere edition du document de reference s’applique(y compris Ies eventuels amendments).

1S0 6165, Engjns de terrassement — Principauxtypes — Vocabulajre

1

.,

IS 11114 (Part 3): 9006ISO 6746-2:2003

3 Terms and definitions

For the purposes of this document, the terms and,

definitions given in ISO 6165 and the following ap-ply.

3.1three-dimensional reference systemsystem used to determine dimensions of earth-moving machines

See Figure 1

3.1.1zero Y planevertical plane which passes through the longitudinalcentreline of the machine

3.1.2X planeany vertical plane perpendicular to the Y plane

3.1.3Z planeany horizontal plane perpendicular to the X and Yplanes

3.1.4positive coordinatepositive direction, forward from the zero X plane,right from the zero Y plane, and above the zero Zplane

NOTE 1 The interaction of the X, Y, Z axes (zeroplanes) is normally located at a well-defined base point:i.e. SIP for a seat as defined in ISO 5353; crankshaftcentreiine for an engine; sprocket or rear axle centrelinefor a tractor-doze~ ground line for machine measure-ments.

NOTE 2 If only components (e.g. engine, seat) areshown, the location and positive direction of the axis fromthe intersection of the X, Y, Z axes (zero planes) assumethe normally expected orientation of the component to amachine, i.e. number one cylinder of engine to the front ofthe machine, seat facing to the front.

NOTE 3 If the machine or its equipment or attachmentor all these are illustrated, a machine driving from right toleft is shown.

3 Termes et definitions

Pour Ies besoins du pr6sent document, Ies termeset definitions donnes clans 1’S0 6165 ainsi que Iessuivants s’appliquent.

3.1systbme de r6f6rence a trois dimensionssyst~me utilis6 pour determiner Ies dimensions desengins de terrassement

Voir Figure 1.

3.1.1plan Y zeroplan vertical qui passe par I’axe longitudinal de l’en-gin

3.1.2plan Xtout plan vertical perpendiculaire au plan Y

3.1.3plan Ztout plan horizontal perpendiculaire aux plans Xet Y

3.1.4coordonnee positivecoordonnee situee clans la direction positive: enavant du plan X zero, a droite du plan Y zero et au-dessus du plan Z zero

NOTE 1 L’intersection des axes X, Y, Z (plans z6ro)est habituellement situ6e en un point de base bien d6fini,a savoir, SIP pour un siege tel que defini clans 1’1S05353,axe du vilebrequin pour un moteur, axe du barbotin ou deI’essieu arriere pour un tracteur, Iigne de r6f6rence au solpour des mesurages sur engins.

NOTE 2 Si I’on a repr6sente uniquement des compo-sants (par exemple un moteur, un sibge), I’emplacementet la direction positive de I’axe par rapport A I’intersectiondes axes X, Y, Z (plans zbro) ont I’orientation normale-ment prevue du composant par rapport a un engin, c’est-a-dire premier cylindre du moteur par rapport A I’avant deI’engin, siege face a I’avant.

NOTE 3 Si un engin ou son bquipement ou ses ac-cessoires ou I’ensemble de ceux-ci sent illustr6s, its sentrepresented comme se depla~ant de droite A gauche.

2

IS 11114 (Pad 3) :2006ISO 6746-2:2003

x

Figure 1 — Three-dimensional reference system

t -z

Figure 1 — Systeme de reference a trois dimensions

IS 11114 (Pad 3): 2006ISO 6746-2:2003

3.2> ground reference plane

GRPplane on which the machine is placed for measure-ments: in the case of the base machine, a hard,level surface; in the case of equipment and attach-ments, either a hard, level surface or compactedearth

NOTE The surface used depends on the intendeduse .of the machine and its equipment and attachments.This needs to be defined when developing specific ISOterminology standards or commercial specifications.

3.3base machinemachine with a cab or canopy and operator-protective structures if required, without equipmentor attachments but possessing the necessarymountings for such equipment and attachments

3.4equipmentset of components mounted onto the base machinewhich allows an attachment to perform the primarydesign function of the machine

3.5attachmentassembly of components that can be mounted ontothe base machine or equipment for specific use

3.6componentpart or an assembly of parts of a base machine,equipment or an attachment

4 General

Examples of dimensions and codes for equipmentand attachments, taken from other InternationalStandards, are given in Annexes A to E. Theseexamples illustrate the use of the three-dimensionalreference system (see Figure 1) and the codingsystem specified in Clause 5 to define such dimen-sions and assign them codes.

The same general principles should be used whendefining, and assigning identifying codes to, otherearth-moving machinery equipment or attachmentdimensions in specific terminology standards orcommercial specifications.

The three-dimensional reference system shall beused to determine the dimensions.

3.2plan de reference au solPRSplan sur Iequel I’engin est place pour Ies mesures:clans Ie cas des engins de base, su,+ace planedure; clans Ie Gas des equipments et accessoires,soit une surface plane dure ou terre compactee

NOTE La surface employee depend de I’utilisatidnnormale de I’engin et de ses equipments et accessoires.II est necessaire de la d~finir clans Ies normes lSO-termi-nologiques s@cifiques et clans les specifications com-mercials.

3.3engin de baseengin, si necessaire avec cabine ou canopy et Iesstructures de protection de I’operateur, saris equi-pments ni accessoires mais pourvu des dispositifsnecessaires a un montage de ces equipments etaccessoires

3.4equipmentensemble d’elements montes sur I’engin de base,qui remplit la fonction primaire de I’engin

3.5accessoireassemblage d’elements, qui peut ~tre monte sur unengin de base pour une utilisation specifique

3.6elementpartie d’un assemblage ou partie d’un engin debase, d’un equipment ou d’un accessoire

4 Generalit6s

Des exemples de dimensions et ‘de codes pour Iesequipments et accessoires, issus d’autres Norme$internationals sent donnes-dans Ies Annexes Aa E. Ces exemples illustrent I’utilisation du systemede reference a trois dimensions (voir Figure 1) et dusysteme de codage specifie clans I’Article’5 pourdefinir de telles dimensions et Ieur assigner des co-des.

II convient que Ies m~mes principes generauxsoient appliques Iors de la definition et de l’as-signation de codes d’identification pour d’autresdimensions d’equipements et d’accessoiresd’engins de base equipant Ies engips de terrasse-ment faisant I’objet de normes termhotogiques oude specifications commercials.

4

IS 11114 (Pati 3): 2006ISO 6746-2:2003

The definitions of dimensions and the specificationof codes for base machine are given in ISO 6746-1.

5 Coding system

Each dimension is assigned a code composed ofcapital letters and a reference number.

Two capital letters shall be used to indicate the typeof equipment or attachment dimension, according tothe following:

HH = height (see Annex A);

Le systdme de r6ference ~ trois dimensions doit&tre utilis6 pour determiner ces dimensions.

Les definitions des dimensions et des codes pourIes engins de base sent donnkes clans1’1S06746-1.

5 Systeme de codification

Un code compose de deux Iettres majuscules etd’un num6ro de r6f6rence est assign6 ~ chaque di-mension.

Deux Iettres majuscules doivent ~tre utilis6es pourindiquer Ie t-ype de dimension de I’Aquipement oude I’accessoire, comme suit

HI{ = hauteur (voir Annexe A);w = width (see Annex B);

WW = Iargeur (voir Annexe B);LL = length (see Annex C);

LL = Iongueur (voir Annexe C);RR = radius or reach (see Annex D);

RR = rayon et port6e (voir Annexe D);AA = angle (see Annex E).

AA = dimension angulaire (voir Annexe E).More than one reference number may be added tothe appropriate capital letters, depending on theneeds of the specific earth-moving equipment or at-tachment for which a standard or commercial speci-fication is being developed.

Plusieurs numeros de r6ference peuvent 6tre ajou-tes aux Iettres majuscules appropri6es, suivant Iesbesoins de l’6quipement ou de I’accessoire deI’engin de terrassement pour Iequel une norme ter-minologique ou une specification commercial esten preparation.

5

IS 11114 (Pati 3): 2006ISO 6746-2:2003

Annex A(normative)

Heights

Annexe A(normative)

Hauteurs

This annex gives examples of equipment and at- La pr6se te annexe donne des exemples de hau-tachment heights and codes showing cases of prac- Jteurs de 6quipements et accessoires et sp6cifietical implementation of the coding system. Ieurs c~es, montrant I’application du syst~me de

codage pour quelques cas particuliers.

6

IS 11114 (Pati 3): 2006ISO 6746-2:2003

7

IS 11114 (Pati 3): 2006ISO 6746-2:2003

>

CodeTerm and definitionTeme et definition Illustration

HH xx maximum height of cutitng edge orteeth

A Adistance on Z coordinate beWeen GRPand cutting edge or teeth at the highest ~ / L-*point that can be reached

t: I /%

t

1GRP

\PRS

hauteur maximale du bord coupant (@> % (@)ou des dents

!

distance sur la coordonn6e Z entre Ie \:‘}

PRS et Ie bord coupant au point Ie plus \ )\

haut pouvant ~tre atteint \\:/

\\—_—2 /’

8

IS 11114 (Pad 3): 2006ISO 6746-2:2003

Annex B Annexe B(informative) (informative)

Wdths Largeurs

Thk annex gives examples of equipment and at- La pr6sente annexe donne des exemples de lar-tachment widths and their codes, showing cases of geurs des 6quipements et accessoires et sp6cifiepractical implementation of the coding system. Ieurs codes, “montrant I’application du systdme de

codage pour quelques cas pati!culiers. -

9

IS 11114 (Pati 3): 2006ISO 6746-2:2003

>

Code,--.,—

Tem and definkionTerme et definit{o!:

width of open grab

distance in Z plane between the furthestpoints of the cutting edges or teeth of theopen grab

Iargeur du grappin ouvert

distance, clans un plan Z, entre Ies points IesPlus eloignes des bords de coupe du grappin2uvert

og grappte width

~istance on Y coordinate between two Y]Ianes passing through the outermost pointsIf the grapple

argeur du grappin ~ Mches

iistance sur la coordonnee Y entre deux)Ians Y passant par Ies points Ies plus ex-erieurs du grappin

illustration

10

IS 11114 (Pati 3): 2006ISO 6746-2:2003

Annex C(informative)

Annexe C(informative)

Lengths Longueurs

This annex gives examples of equipment and at- La pr6sente annexe donne des exem.pies de lon-tachment lengths and their codes, showingcases of gueurs des 6quipements et accessoires et s@cifie-practical“implementationof the coding system. Ieurs codes, montrant I’application du syst6me de

codage pour quelques cas paticuhers. -

11

IS lll14(Pad3) :2006ISO 6746-2:2003

Annex D(informative)

Radial and reach dimensions

Annexe D(informative)

Rayons et portees

This annex gives examples of equipment and at- La pr6sente annexe donne des exemples de rayonstachment radial and reach dimensions and their et de port6es des 6quipements et accessoires etcodes, showing cases of practical implementation of specifie Ieurs codes, montrant I’application du sys-the coding system. teme de codage pour quelques cas particuliers.

12

IS 11114 (Pati 3): 2006ISO 6746-2:2003

Annex E Annexe E(informative) finformative)

Angular dimensions Dimensiom angulaires

This annex gives examples of equipment and at- La pr6sente annexe donne des exemples de de-tachment angles and their codes, showing cases of mensions angulaires des 6quipements et acces-practical implementation of the coding system. soires et sp6cifie Ieurs codes, montrant I’application

du syst6me de codage pour quelques cas par-ticuliers.

13

IS 11114 (Pati 3) :2006ISO 6746-2:2003

Bibliography Bibliographic

[1] ISO 5353, Earth-moving machine~, and [1] ISO 5353, Engins de terrassement, et trac-tractors and machine~ for agriculture and teurs et materiels agricoles et foresters —forest~ — Seat index point Point repere du siege

14

.-__. —___ —.-.—

Bureau of Indian Standards

BIS is a statutory institution established under the Bureau of /ndian Standards Act, 1986 to promote

harmonious development of the activities of standardization, marking and quality certification of

goods and attending to connected matters in the country.

Copyright

BIS has the copyright of all its publications. No part of these publications may be reproduced in any

form without the prior permission in writing of BIS. This does not preclude the free use, in the course

of implementing the standard, of necessary details, such as symbols and sizes, type or grade .

designations. Enquiries relating to copyright be addressed to the Director (Publication), BIS.

Review of Indian Standards

Amendments are issued to standards as the need arises on the basis of comments. Standards are also

reviewed periodically; a standard along with amendments is reaffirmed when such review indicates that

m changes are needed; if the review indicates that changes are needed, it is taken up for revision.

Users of Indian Standards should ascertain that they are in possession of the latest amendments or

edition by referring to the latest issue of ‘BIS Catalogue’ and ‘Standards: Monthly Additions’.

This Indian Standard has been developed from Dot: No. ME 07 (0842).

Amendments Issued Since Publication

Amend No. Date of Issue Text Affected

BUREAU OF INDIAN STANDARDS

Headquarters:

Manak Bhavan, 9 -dur Shah Zafar Marg, New Delhi 110002Telephones 23230131,23233375,2323 9402 websjfe: www.bis.org. in

Regional Offices: Telephones

Central : Manak Bhavan, 9 Bahadur Shah Zafar Marg{

23237617NEW DELHI 110002 23233841

Eastern : 1/14 C.I.T. Scheme Vil M, V.I,P. Road, Kankurgachi{

23378499,23378561KOLKATA 700054 23378626,23379120

Northern : SCO 335-336, Sector 34-A, CHANDIGARH 160022{

26038432609285

Southern : C.I.T. Campus, IV Cross Road, CHENNAI 600113{

22541216,2254144222542519,22542315

Western : Manakalaya, E9 MlDC, Marol, Andheri (East){

28329295,28327858MUMBAI 400093 28327891,28327892

Branches: AHMEDABAD. BANGALORE. BHOPAL. BHUBANESHWAR, COIMBATORE, FARIDABAD.

GHAZIABAD. GUWAHATI. HYDERABAD. JAIPUR. KANPUR. LUCKNOW. NAGPUR.

NALAGARH. PATNA. PUNE. RAJKOT. THIRUVANANTHAPURAM. VISAKHAPATNAM.

Printed at Simco Printing Press, Delti