introduction
DESCRIPTION
h. Soap-film bubble. 2D sinusoid interface. Retractable injector. Oscillating pistons. Shock-bubble interaction configuration. Richtmyer-Meshkov instability configuration. Experiments and Computations for Inertial Confinement Fusion-Related Shock-Driven Hydrodynamic Instabilities - PowerPoint PPT PresentationTRANSCRIPT
0 1 2 3 4 5 6 7 8
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
k (
-
0 )
Comparison of dimensionless amplitude with several models
Exp. M = 1.26Exp. M = 2.05Raptor M = 1.26Raptor M = 2.05Mikaelian M = 1.26Mikaelian M = 2.05Sadot et al. M = 1.26Sadot et al. M = 2.05Dimonte M = 1.26Dimonte M = 2.05
0 5 10 150
0.2
0.4
0.6
0.8
1
M=1.33M=2.88M=3.38
0 5 10 150
0.2
0.4
0.6
0.8
1
M=1.2M=1.5M=1.68M=3
0 5 10 150
0.2
0.4
0.6
0.8
1
M=1.14M=2.5M=5
0 5 10 150
0.2
0.4
0.6
0.8
1
M=1.2M=1.5M=1.68M=3
Experiments and Computations for Inertial Confinement Fusion-Related Shock-Driven Hydrodynamic InstabilitiesExperiments and Computations for Inertial Confinement Fusion-Related Shock-Driven Hydrodynamic InstabilitiesBradley Motl, John Niederhaus, Devesh Ranjan, Jason Oakley, Mark Anderson, and Riccardo Bonazza
Fusion Technology Institute, University of Wisconsin-MadisonHigh Energy Density Physics Summer School, San Diego, CA, July 29 - August 3, 2007
IntroductionIntroduction
Shock-bubble interactionShock-bubble interaction
Relevance to ICFRelevance to ICF
Wisconsin Shock Tube LaboratoryWisconsin Shock Tube Laboratory
In inertial confinement fusion, shock-driven hydrodynamic instab-ilities and the associated mixing impose a limit on the efficiency with which fuel material may be compressed to the densities required for fusion, reducing the obtainable fusion yield. These instabilities arise at nonuniformities on density and material interfaces, as ablative and radiatively-driven shocks pass through the material and compress it, as shown below schematically.
In the present work, the phenomenology, mechanisms, and spatial and temporal scales of shock-driven instabilities are investigated using experiments in a gas shock tube environment, along with numerical simulations. In the shock tube environment, hydrodynamic phenomena may be characterized much more precisely than at ICF conditions, due to differences in conditions listed in the table above. Further, the absence of electric and magnetic fields, phase changes, and radiation allows purely hydrodynamic effects to be studied independently. Here, geometric length scales of the deformed interfaces are measured as indications of shock-induced mixing.
Computational parameter studyComputational parameter study
ReferencesReferencesD. Ranjan, J. Niederhaus, B. Motl, M. Anderson, J. Oakley, and R. Bonazza, Experimental investigation of primary and secondary features in high Mach number shock-bubble interaction, Phys. Rev. Lett., in review (2006).
D. Ranjan, M. Anderson, J. Oakley, and R. Bonazza, Experimental investigation of a strongly shocked gas bubble, Phys. Rev. Lett., 94 (2005).
J. Niederhaus, D. Ranjan, J. Oakley, M. Anderson, and R. Bonazza, Inertial-Fusion-Related Hydrodynamic Instabilities in a Spherical Gas Bubble Accelerated by a Planar Shock Wave, Fusion Science and Technology 47, 4 (2005), p. 1160.
J. Greenough, J. Bell, and P. Colella, An adaptive multi-fluid interface capturing method for compressible flows in complex geometry, AIAA Paper 95-1718.
)( 0 p
7.2 m
2 m
Shock tube:
• Vertical orientation• 20 MPa impulsive
load capability• 25.4 cm square internal
cross section• Planar laser
imaging ports• Modular components:
– Bubble injector– Oscillating pistons
Imaging:
• Pulsed laser sheets
• CCD cameras• Mie scattering or
planar laser induced fluor-escence
• Dual exposure
Shock-bubble interaction
configuration
Soap-film bubble
Retractable injector
Richtmyer-Meshkov instability
configuration
Oscillating pistons
2D sinusoid interface
Driver(high pressure)
Diaphragm
Shockwave
propagation
Light source
Diagnostic laser sheet
Experiment
Raptor (2D)
τ = 0.00 τ = 4.66 τ = 8.79
τ = 0.00 τ = 1.54
τ = 0.00 τ = 1.53
τ = 3.98 τ = 4.16τ = 3.29
τ = 4.22τ = 3.95τ = 3.27
N2(acetone) / SF6 M = 1.26
Richtmyer-Meshkov instabilityRichtmyer-Meshkov instability
N2(smoke) / SF6
M = 2.05
AcknowledgementsAcknowledgementsThe authors would like to express sincere thanks to Jeff
Greenough (LLNL), for facilitating computations, and Paul Brooks (UW-Madison) for developing and maintaining the experimental setup. This work was supported by US DOE Grant #DE-FG52-03NA00061.
These flows are simulated numerically by integrating the 3D Euler equations using a piecewise-linear 2nd-order Godunov method with adaptive mesh refinement (AMR). The code is called Raptor, and was developed at LLNL and LBL (see Greenough, et al.). A computational parameter study was performed for shock-bubble interactions, with 14 scenarios at 1.14 ≤ M ≤ 5 and -0.76 ≤ A ≤ 0.61.
= 1.3 = 4.1 = 7.7 = 11.5
8 cm
= 23.6
= 1.3 = 4.0 = 7.7 = 11.6 = 23.8
5 cm
= 45.6 = 46.3
8 cm
= 63.5 = 71.6 = 63.5 = 69.5
M = 1.4 M = 2.08 M = 2.95 = 65.7 = 63.5 = 71.6
f1
Rut /1
The results above show the growth of the mixed region within the shocked bubble as a function of dimensionless time, with M and A as parameters. This is quantified as , where is the mean volume fraction of the ambient gas within the bubble region. These data show that the intensity and extent of mixing increases with increasing values of the Atwood number A, though Mach number effects may be scaled out using the post-shock flow speed.
(b) (d)(c)(a)
The evolution of the Richtmyer-Meshkov instability is shown schematically above: (a) initial configuration just prior to shock, (b) linear growth regime, (c) start of nonlinear growth, (d) appearance of mushroom structures, and (e) turbulent mixing.
Below are images generated using planar laser diagnostics (PLIF or Mie scattering) from shock tube experiments studying the Richtmyer-Meshkov instability for a 2D sinusoidal interface between nitrogen (with flow tracer) above and SF6 below.
(e)
Instability evolution
Mr
Mt
Mi
(+) (-)
p
He bubble in air: A = -0.76 Ar bubble in N2: A = 0.18
Kr bubble in air: A = 0.49 R12 bubble in air: A = 0.61
The evolution of a helium bubble of initial radius R during and after acceleration by a planar shock wave in air is shown schematically above: (a) initial configuration; (b) compression and rotation induced by shock passage; (c) deformation and vortex ring formation.
(b) (c)(a)
p
(+)(-)
tk 0
Mi
Shock-driven hydrodynamic instabilities are present in accelerated inhomogeneous flows. Vorticity is deposited on density interfaces by baroclinicity , causing interfaces to become unstable and deform. The geometric features of the deformed interfaces and mixing zones in two particular shock-driven flows are studied here: the Richtmyer-Meshkov instability of a planar interface with a small-amplitude sinusoidal perturbation, and the interaction of a planar shock wave with a discrete spherical bubble.
t = 13 s t = 35 s t = 70 s t = 113 s t = 230 s
Bubble distortion
t = 430 s t = 721 s t = 725 s
Top: experimental shock tube images obtained using laser light scattered at the bubble midplane for a helium bubble shocked at M = 2.95. Bottom: results from 3D Eulerian AMR simulations: density (left) and vorticity magnitude (right) at bubble midplane.
Below: late-time experimental and numerical images showing multiple vortex rings and complex structure. Left: helium volume fraction ( f ); right:
vorticity magnitude ().
RtWt /
Late-time images for varying Mach number.
Radiative heating
Ablation Compression Thermo-nuclear burn
Fusion Technology InstituteUW-Madison
21
21
A
Results from simulations with Raptor (2D) are also shown above, At left, the dimension-less amplitude of the interface (excluding wall effects) from simulations and experiments at various shock strengths (M) is plotted on a dimensionless timescale, with analytical model predictions.
= post-shock particle velocity
Wt = transmitted shock wave speed
R = initial bubble radius
k = perturbationwavenumber
tk 0
ICF Shock tube
L scale 10-6 m 10-2 m
T scale 10-9 s 10-6 s
scale 103 kg/m3 100 kg/m3
M ~30 ≤ 5
A [-1,1] [-1,1]
0 20 40 600
1
2
3
4M=1.45 Expt.M=2.08 Expt.M=2.95 Expt.
RtWt /
h
)2/( RhLh
h / (
2R)
f
100
10-6
[logscale]
max
-max
0
1u
B
B
dV
dVf
1
B = bubble-fluid region (f ≠ 0)
f = bubble-fluid volume fraction