intelligent control terminal-dlp panel programming dlp lcd panel programming front
TRANSCRIPT
Intelligent control terminal-DLP panel Programming
DLP LCD PANEL Programming
Front
Device subnet ID and device ID
Can make remark according to actual location, convenience for maintenance and management
Set the backlight, Higher value make the Great Lightness, And vice versa
DLPINTERFACE FUNCTION
DLP Key number
Remark of each keys
Mode of each keys
Targets of keys
Page
DLP P
ANELINTERFACE FUNCTION
Enter the number of buttons control target, when in single mode only have one targets as default , when In combination mode can
enter multiple, up to 99 .
Signal – ON: only execute a single event on ( only to control a target on)Signal – off: only execute a single event off( only to control a target off)Signal –on/ off: only execute a single event on/off( can control a target on/off)inching: Pressing will on , otherwise off, control single event .Note : control type is common switch and curtain switchCombination On: only execute combination event on ( can control multi-targets on)Combination off: Only execute combination event off( can control multi-targets off)Combination on/off: can execute combination event on/ off ( can control multi-targets on/off)
Key control mode
DLP p
anelStart
programming
1 、 click "combination way”
2 、 Select a Key combination way, The default is the first type, see the picture, in Blue is a combination , Blue part is combine together, White part is separated
Combination way
example : In picture A selected the third (3) combination way . see Picture B key one and key two combined into one key. Then press key one or key two , the effect would be same as press key one .In picture B , key 3 and key 4 is combined as one key, then press key three or key four , the effect would be same as press key three . In other combination way , Blue part is combine together and set the first key, the white part is independence to control
Picture A
1
2
1
2
3
4
1 、 set the remark for each
key
2,Input Remark for each Key
3 、 save
DLP P
ANEL
1 、 Click “Mode” to set the mode for each key
2 、 Key mode selection
3 、 save
DLP P
ANEL
Signal – ON: only execute a single event on ( only to control a target on)Signal – off: only execute a single event off( only to control a target off)Signal –on/ off: only execute a single event on/off( can control a target on/off)inching: Pressing will on , otherwise off, control single event .Note : control type is common switch and curtain switchCombination On: only execute combination event on ( can control multi-targets on)Combination off: Only execute combination event off( can control multi-targets off)Combination on/off: can execute combination event on/ off ( can control multi-targets on/off)
Common Key control mode
1 、 Click” Pic download” , set the display content of key
2 、 Select the download status
3 、 Double click the key that need to download pictures. Note The picture format is in BMP , Size is different according to the combination way, please download see the remark near the button to download correct pictures
DLP P
ANEL
4 、 select Picture from the Pop-up choice box ,need to in BMP Format, please make the Dimensions as per request
5 、 Open
DLP P
ANEL
6 、 download all the selected picture for each button in current status
Signal button download
DLP
7 、 When system pop-up “All download success” , can check if the display in DLP panel is change
DLP
10 、 download all the selected picture for each button in current status
8 、 select “ On Status” to download the key picture when it is in pressing status
9 、 Double click the key that need to download pictures, the format need to be BMP. Size is different according to the combination way, please download see the remark near the button to download correct pictures
1 、 Click “function” to set
the detail function of each
key
2 、 if it is combination on/off mode ,input the type of the target address which need to be control
3 、 save
DLP P
ANEL
Select AC function
AIR CONDITIONNING CONTROL FUNCTION
select “enable "to start AC function, if it is central AC, Need to enter the AC module address 。Set temperature compensation, compensation for the
difference between display temperature and actual temperature .because according to the installation position ,the temperature would have differences..
Read panel actual status, including temperature , Fan speed. mode and other information , can set the parameters .then click " save" to send control command to panel 。
ON/ Unlock panel AC Control page
To specify the target network or broadcast the panel temperature
DLP P
anel
AC CONTROL FUNCTION
1 、 Make sure “ IR emission replays function” is selected , otherwise can not send the selected information
2 、 Select the model that need to set the control targets
3.set the control targets of each mode ,As picture select "cooling. Heating" .then in information of Air conditioning , need to fill control targets of each temperature value, the type is universal switch
Tip: How to know the control target?Control target is learn air conditioning remote control keys code by IR Learner.Then Upload to SB-EM-IR ( Infrared transmitter ) control code position information.To Know the specific target , just entre the in Infrared transmitter setting interface