instructions for wallet - heirloom creations · pickle pie designs zipper let’s get started!...

20
TM Wonderful Wallets f 1 Stitch a sweet Wallet with room to hold credit cards, cash, and receipts. Copyright Pickle Pie Designs 2017 Medium Large

Upload: others

Post on 11-Aug-2020

0 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: Instructions for Wallet - Heirloom Creations · Pickle Pie Designs Zipper Let’s Get Started! Snaps and Snapsetter Tool Tearaway Stabilizer Fusible Cutaway Mesh Stabilizer (for optional

TM

Wonderful Wallets

f

1

Stitch a sweet Wallet with room to hold credit cards, cash, and receipts.

Copyright Pickle Pie Designs 2017

Medium

Large

Page 2: Instructions for Wallet - Heirloom Creations · Pickle Pie Designs Zipper Let’s Get Started! Snaps and Snapsetter Tool Tearaway Stabilizer Fusible Cutaway Mesh Stabilizer (for optional

2

Fabric 1: 1/4 yard or Fat Quarter

Fabric 2: Large: 1/2 yard Medium or Small: 1/4 yard or Fat Quarter

Fabric 3 (non-directional): Large or Medium: 1/4 yard Small 1/4 yard or Fat Quarter

Scrap of Clear Vinyl, 12 gauge Pickle Pie Designs Zipper

Let’s Get Started!

Snaps and Snapsetter Tool Tearaway Stabilizer Fusible Cutaway Mesh Stabilizer (for optional

Scrappy Pocket) Lightweight Fusible Interfacing Fusible Webbing Fusible Seam Tape Microtex Needle, size 80/12 Thread to match fabrics Heat soluble marking pen Water Soluble Topping

Gather your supplies…

Copyright Pickle Pie Designs 2017

Design info…Inside Fabric Placement…

Size: Design Size: Hoop Size:

Large 7.4” x 11.7” 8x12

Medium 4.3” x 9.2” 6x10

Small 4.3” x 6.9” 5x7

Optional Scrappy Pocket 6.9” x 12.3” 9x14

Fabric A

Fabric C

Fabric D

Fabric E

Page 3: Instructions for Wallet - Heirloom Creations · Pickle Pie Designs Zipper Let’s Get Started! Snaps and Snapsetter Tool Tearaway Stabilizer Fusible Cutaway Mesh Stabilizer (for optional

3Copyright Pickle Pie Designs 2017

A few notes before you begin… All sizes listed are width x length Do NOT use a zipper with metal teeth! There is an optional Scrappy Pocket included for those with an extra large embroidery field of at least 7.5” x 12.8”. The pocket fits the Large design only. If you are making the Scrappy Pocket, you will skip Fabric OP and instead cut fabrics for the Scrappy Pocket using the chart on page 8. You will need to complete the Scrappy Pocket in its own hooping before you hoop and stitch the wallet. It is suggested that you skip vinyl in the Small Wallet as it creates extra bulk in the small. Please respect our copyright. You cannot share, give away, or resell the design files and/or instructions or alter them and call them your own. You MAY create up to 500 finished products for

resale at craft fairs, on Etsy, etc., and we wish you much success if you offer them for sale!

Page 4: Instructions for Wallet - Heirloom Creations · Pickle Pie Designs Zipper Let’s Get Started! Snaps and Snapsetter Tool Tearaway Stabilizer Fusible Cutaway Mesh Stabilizer (for optional

4Copyright Pickle Pie Designs 2017

1 Project Outline Match/coordinate with Fabric A

2 Zipper Placement Line Match/coordinate with Fabric A

3 Zipper Tack Down Match/coordinate with Fabric A

4 Tack Down Fabric A (Coin Pouch Front) Match/coordinate with Fabric A

5 Tack Down Fabric B (Coin Pouch Lining) Match/coordinate with Fabric A

6 Placement Lines for Fabric C (Cash Pocket) Match/coordinate with Fabric A

7 Tack down Fabric C Match/coordinate with Fabric E

8 Tack down Fabrics D and E Match/coordinate with Fabric E

9 Placement Lines for Fabric OP (Back Pocket) Match/coordinate with Fabric E

10 Tack down Fabric OP (Back Pocket) Match/coordinate with Fabric E

11 Tack down Fabric F Match/coordinate with Fabric E

Wonderful Wallet Stitch Sequence/Color Chart…

Page 5: Instructions for Wallet - Heirloom Creations · Pickle Pie Designs Zipper Let’s Get Started! Snaps and Snapsetter Tool Tearaway Stabilizer Fusible Cutaway Mesh Stabilizer (for optional

Prepare your materials…

Copyright Pickle Pie Designs 2017

Follow the charts below to cut & label your materials, finding the columns for your chosen organizer size. Feel free to mix and match your fabrics!

For: Label: Large Medium Small

Outer Pocket OP 15” x 13” 9” x 11” 9” x 9”

Lower Pocket C 9” x 9” 6” x 7” 6” x 5”

Back F 9” x 13” 6” X 11” 6” x 8”

Cut Fabric 1…

5

For: Label: Large Medium Small

Strip above Zipper D 9” x 2” 6” X 2” 6” X 2”

Card Pockets *Non-directional print

E 25” x 9” 17” X 6” 9.5” x 6”

Cut Fabric 2…

For: Label: Large Medium Small

Coin Pouch Front A 9” x 10” 6” X 8” 6” x 5”

Coin Pouch Lining B 9” x 6” 6” X 5” 6” x 5”

Cut Fabric 3…

Page 6: Instructions for Wallet - Heirloom Creations · Pickle Pie Designs Zipper Let’s Get Started! Snaps and Snapsetter Tool Tearaway Stabilizer Fusible Cutaway Mesh Stabilizer (for optional

Copyright Pickle Pie Designs 2017

Cut Fusible Interfacing…For: Label: Large Medium Small

Fabric C C 9” x 4.5” 6” X 3.5” 6” x 2.5”

Fabric F F 9” x 13” 6” X 11” 6” x 8”

6

Cut Vinyl…For: Label: Large Medium Small

Card Pocket Vinyl 9” x 2.5” 6” x 2.5” Optional - 6” x 2.5”

Cut Fusible Webbing…For: Label: Large Medium Small

Card Pockets E 25” x 9” 17” X 6” 9.5” x 6”

Page 7: Instructions for Wallet - Heirloom Creations · Pickle Pie Designs Zipper Let’s Get Started! Snaps and Snapsetter Tool Tearaway Stabilizer Fusible Cutaway Mesh Stabilizer (for optional

7 Copyright Pickle Pie Designs 2017

Prep Your Materials…

Fold Fabric C in half lengthwise, wrong sides together, and press to crease.

Slide Interfacing C inside, butting it up against the inner fold and press. Set aside.

Fold Fabric A in half lengthwise, wrong sides together, and press to crease. Set aside.

Fold Fabric D in half, lengthwise, wrong sides together, and press to crease.

Open Fabric D and fold each long edge to the center. Press to crease.

Fold Fabric D in half once more. Press to crease.

Set aside.

Press Fusible Webbing E to the wrong side of Fabric E. Set aside.

Page 8: Instructions for Wallet - Heirloom Creations · Pickle Pie Designs Zipper Let’s Get Started! Snaps and Snapsetter Tool Tearaway Stabilizer Fusible Cutaway Mesh Stabilizer (for optional

8 Copyright Pickle Pie Designs 2017

Press Interfacing F to the wrong side of Fabric F. Set aside.

Fold Fabric OP in half widthwise, wrong sides together, and press to crease. Set aside.

Press fusible webbing to the back of Fabric E. Be

sure to leave the paper backing on the fusible

webbing for now.

Fold the card pockets, accordian-style, following

graphics on the following pages; Measure and mark

Fabric E along the dotted lines shown, using an

erasable marking pen. You can also snip each

measurement into the seam allowance, which will be

very helpful when you bring the piece to the ironing

board to press the folds.

After measuring and marking, fold each section on

the dotted line. You will alternate between outward

folds and inward folds to create the card pockets for

your wallet. Press each fold to crease it.

When you are done, carefully remove the paper

backing on the webbing, and refold. Place a pin at the

lower edge of the fabric to mark it as the lower edge.

Place the backing paper on the back to cover the

adhesive, then set aside.

Create the Card Pockets…

Page 9: Instructions for Wallet - Heirloom Creations · Pickle Pie Designs Zipper Let’s Get Started! Snaps and Snapsetter Tool Tearaway Stabilizer Fusible Cutaway Mesh Stabilizer (for optional

Copyright Pickle Pie Designs 20179

Small Card Pockets…

2.5”

1.75”

5.25”

Outward fold

Inward fold

Fabric E

2”

1.75”

5”

1.75”

2”

1.75”

2.5”

Outward fold

Inward fold

Outward fold

Inward fold

Outward fold

Inward fold

Medium Card Pockets…

Fabric E

Page 10: Instructions for Wallet - Heirloom Creations · Pickle Pie Designs Zipper Let’s Get Started! Snaps and Snapsetter Tool Tearaway Stabilizer Fusible Cutaway Mesh Stabilizer (for optional

Copyright Pickle Pie Designs 201710

Large Card Pockets…

3”

2.5”

2”

6”

2”

2.5”

2”

2.5”

2”

Inward fold

Outward fold

Inward fold

Outward fold

Inward fold

Outward fold

Inward fold

Outward fold

Fabric E

Page 11: Instructions for Wallet - Heirloom Creations · Pickle Pie Designs Zipper Let’s Get Started! Snaps and Snapsetter Tool Tearaway Stabilizer Fusible Cutaway Mesh Stabilizer (for optional

11

For: Label: Extra Large

Pocket Strip 1 P1 13” x 14”

Pocket Strip 2 P2 3.5” x 14”

Pocket Strip 3 P3 3.5” x 14”

Pocket Strip 4 P4 3” x 14”

Cut 4 different fabrics to these sizes…

Optional Scrappy Pocket Fabric Prep… If you are making a Scrappy Pocket, you must stitch it before stitching the Wallet design. To fit this optional pocket, your hoop must be able to accommodate a design measuring 7.5” x 12.8”. The Scrappy Pocket fits the LARGE Wallet only. When you are making this Scrappy Pocket, you will skip “Fabric OP” in the cutting charts and use this finished piece in its place.

Page 12: Instructions for Wallet - Heirloom Creations · Pickle Pie Designs Zipper Let’s Get Started! Snaps and Snapsetter Tool Tearaway Stabilizer Fusible Cutaway Mesh Stabilizer (for optional

12

Stitch Sequence: For: Thread Color:

1 Project Outline Match/coordinate with Fabric P1

2 Placement line for Fabric A Match/coordinate with Fabric P1

3 Tack down Fabric A Match/coordinate with Fabric P1

4 Quilting Stitches on Fabric A Match/coordinate with Fabric P1

5 Tack down Wrong Side of Fabric B Match/coordinate with Fabric P2

6 Tack down Right Side of Fabric B Match/coordinate with Fabric P2

7 Quilting Stitches on Fabric B Match/coordinate with Fabric P2

8 Tack down Wrong Side of Fabric C Match/coordinate with Fabric P3

9 Tack down Right Side of Fabric C Match/coordinate with Fabric P3

10 Quilting Stitches on Fabric C Match/coordinate with Fabric P3

11 Tack down Wrong Side of Fabric D Match/coordinate with Fabric P4

12 Tack down Right Side of Fabric D Match/coordinate with Fabric P4

13 Quilting Stitches on Fabric D Match/coordinate with Fabric P4

Optional Scrappy Pocket Stitch Sequence/Color Chart…

Copyright Pickle Pie Designs 2017

Page 13: Instructions for Wallet - Heirloom Creations · Pickle Pie Designs Zipper Let’s Get Started! Snaps and Snapsetter Tool Tearaway Stabilizer Fusible Cutaway Mesh Stabilizer (for optional

13

Optional: Stitch a Scrappy Pocket for the Large Wallet…

Load the “Scrappy Pocket” design to your embroidery machine…

3. Center Fabric P1, right side up, over the left side of the main project outline, butting the right edge up against the placement line, as shown. Tape in place and Sew Stitch Sequence 3 to tack down Fabric P1.

Copyright Pickle Pie Designs 2017

4. Sew Stitch Sequence 4 to sew the quilting stitches on Fabric P1.

1. Hoop a piece of fusible mesh stabilizer with the fusible side down. Using thread to coordinate with Fabric P1, sew Stitch Sequence 1 directly on your stabilizer to create the main project outline.

2. Sew Stitch Sequence 2 to create a placement line for Fabric P1.

Page 14: Instructions for Wallet - Heirloom Creations · Pickle Pie Designs Zipper Let’s Get Started! Snaps and Snapsetter Tool Tearaway Stabilizer Fusible Cutaway Mesh Stabilizer (for optional

14 Copyright Pickle Pie Designs 2017

5. Change to thread to coordinate with Fabric P2. Center Fabric P2, right side down, across the right edge of Fabric P1. Tape in place on the top and bottom. Sew Stitch Sequence 5 to tack the the wrong side of Fabric P2.

6. Flip Fabric B to the right, covering the seam, so it is now right side up. Finger press the seam well and tape in place. Sew Stitch Sequence 6 to tack down the right side of Fabric P2.

7. Sew Stitch Sequence 7 to sew the quilting stitches on Fabric P2.

8. Change to thread to coordinate with Fabric P3. Center Fabric P3, right side down, against the right stitch line on Fabric P2. Tape in place on the top and bottom. Sew Stitch Sequence 8 to tack down the wrong side of Fabric P3.

9. Flip Fabric P3 to the right, covering the seam, so it is now right side up. Finger press the seam well and tape in place. Sew Stitch Sequence 9 to tack down the right side of Fabric P3.

10. Sew Stitch Sequence 10 to sew the quilting stitches on Fabric P3.

Wro

ng

Sid

e

Fa

bric

P2

Wro

ng

Sid

e

Fa

bric

P3

Page 15: Instructions for Wallet - Heirloom Creations · Pickle Pie Designs Zipper Let’s Get Started! Snaps and Snapsetter Tool Tearaway Stabilizer Fusible Cutaway Mesh Stabilizer (for optional

15 Copyright Pickle Pie Designs 2017

11. Change to thread to coordinate with Fabric P4. Center Fabric P4, right side down, across the right stitch line on Fabric P3. Tape in place on the top and bottom. Sew Stitch Sequence 11 to tack the the wrong side of Fabric P4.

12. Flip Fabric P4 to the right, covering the seam, so it is now right side up. Finger press the seam well and tape in place. Sew Stitch Sequence 12 to tack down the right side of Fabric P4.

13. Sew Stitch Sequence 13 to sew the quilting stitches on Fabric P4.

14. Remove the project from the hoop. Trim off the excess stabilizer on the back, right up to the stitch lines.

15. Fold Fabric P1 to the back, wrong sides together, creating the fold along the edge of the quilting stitches on Fabric P1. Press to fuse the stabilizer to the back of Fabric P1.

Set the Scrappy Pocket aside and continue to stitch the Wallet design…

Wro

ng

Sid

e

Fa

bric

P4

Fold

Page 16: Instructions for Wallet - Heirloom Creations · Pickle Pie Designs Zipper Let’s Get Started! Snaps and Snapsetter Tool Tearaway Stabilizer Fusible Cutaway Mesh Stabilizer (for optional

16

Load the Wonderful Wallet design to your embroidery machine.

3. Center your zipper within the placement line, right side up, with the zipper pull falling at least 1” over the left stitch line. Tape in place to secure.

Sew Stitch Sequence 3 to tack down the zipper.

Copyright Pickle Pie Designs 2017

4. Place Fabric A over the bottom of the project, with the fold aligned just below the zipper teeth.Tape in place along the raw edges.

Sew Stitch Sequence 4 to tack down the fabric.

Sew Stitch Sequence 1 directly on your stabilizer to create a project outline.

1. Hoop a piece of tearaway stabilizer.

2. Sew Stitch Sequence 2 to create a placement line for your zipper.

Stitch the Wallet…

Fold

Page 17: Instructions for Wallet - Heirloom Creations · Pickle Pie Designs Zipper Let’s Get Started! Snaps and Snapsetter Tool Tearaway Stabilizer Fusible Cutaway Mesh Stabilizer (for optional

17 Copyright Pickle Pie Designs 201717

5. Remove the hoop from the machine and turn it over to the back. Place Fabric B over the bottom of the project, right side down, aligning the top edge of Fabric F about 1” over the top of the zipper. Tape in place well.

Replace the hoop on your machine and sew Stitch Sequence 5 to tack down the fabric. Note that this stitch line will not connect, to prevent it from stitching the zipper closed.

9. Place the piece over the project, aligning the fold of Fabric D just above the top zipper teeth. Remove the clips. Tape in place along the sides, taking care to assure the accordion folds in Fabric E are straight. Cover with a piece of water soluble topping to prevent the presser foot from catching in a fold during the next step. Tape in place.

6. Sew Stitch Sequence 6 to create placement lines for Fabric C.

7. Place Fabric C over the project, with the fold aligned across the placement lines. Tape in place along the sides and lower edge.

Sew Stitch Sequence 7 to tack down Fabric C.

8. Open the the fold of Fabric D. With the fold of Fabric D on the bottom, slide the the lower edge of Fabric E into the fold (remove the pin you previously placed on the bottom of Fabric E.) Place the vinyl in front of Fabric E, butting a long edge of vinyl into the fold. Use a clip to hold the fabrics inside the fold of Fabric D.

10. Sew Stitch Sequence 8 to tack down Fabrics D and E, and the vinyl. On the Large Wallet, there will be a stitch down the vertical center of the pockets as well.

Fold

Fabric D Fold

Fabric E

Fabric D Fold (above zipper teeth)

Fabric E

Page 18: Instructions for Wallet - Heirloom Creations · Pickle Pie Designs Zipper Let’s Get Started! Snaps and Snapsetter Tool Tearaway Stabilizer Fusible Cutaway Mesh Stabilizer (for optional

18 Copyright Pickle Pie Designs 201718

14. Center Fabric F over the project, right side down. Tape in place. Sew Stitch Sequence 11 to tack down Fabric F and complete the stitching.

13. Center the fold of the pocket, right side (or scrappy pieced side) down, across the placement lines. Tape in place. Sew Stitch Sequence 10 to tack down the pocket along the left side.

11. Remove the Water Soluble Topping. Sew Stitch Sequence 9 to create placement lines for Fabric OP (or the Scrappy Pocket, if you made one.)

12. DO NOT MISS THIS STEP! Unzip the zipper 2/3 of the way across the project. If you forget this step, your zipper pull will get stitched outside the seam line and the zipper will not open!

15. Remove the project from the hoop. Trim around the project leaving a 1/4 seam allowance, and using pinking shears to reduce bulk in the seam. Clip corners.

Fabric H Fold

16. Turn the project right side out through the side opening.

Page 19: Instructions for Wallet - Heirloom Creations · Pickle Pie Designs Zipper Let’s Get Started! Snaps and Snapsetter Tool Tearaway Stabilizer Fusible Cutaway Mesh Stabilizer (for optional

Copyright Pickle Pie Designs 2017

17. Fold in the opening and press to crease. Place a piece of fusible seam tape to in the seam opening, and press to fuse it closed.

19. Unzip the zipper all the way and gently poke through the tearaway stabilizer behind the zipper. Gently remove the remaining tearaway stabilizer from inside the zippered section of the wallet.

18. Turn the pocket around to the back of the wallet and press.

20. Install the male snap parts on the top rounded flap, approximately 1/4” down from the top. The male side should face the inside of the wallet and will go through all of the layers in the flap.

21. Locate the placement for the female snap part by closing the wallet, noting where the male part sits. Mark this spot on the back pocket, underneath the flap.

22. Install the female snap parts only through the back pocket layers. The flat side of the snap will hide in the pocket, and the female side will show on the outside of the pocket.

19

Page 20: Instructions for Wallet - Heirloom Creations · Pickle Pie Designs Zipper Let’s Get Started! Snaps and Snapsetter Tool Tearaway Stabilizer Fusible Cutaway Mesh Stabilizer (for optional

You’ re done!

Copyright Pickle Pie Designs 2017

f

20

www.picklepiedesigns.com

facebook.com/picklepiedesigns

pinterest.com/picklepiedesign

[email protected]

TM

Visit your local retailer for more ‘in the hoop’ projects from Pickle Pie Designs!