instructions for installation mixing valve motor for 1-1/2 & 2 … · 2017-07-16 ·...
TRANSCRIPT
Instructions for installationMixing Valve Motor for 1-1/2" & 2" Valves
L658150 March 24, 2010
1) Turn mixing valve handle so that the mixing valve is closed. Remove the mixing valve handle and indication gauge.
Right Hand Mounting Instructions
2) Screw in the supplied pin.
3) Push in and turn the mixing valve motor knob so that the A side is fully open.
(turn same direction as valve was turned)
4) Remove the mixing valve motor knob by pulling it out.
5) Put the supplied plastic coupling attachment (with grooves facing outward) into the back of the mixing valve motor.
6) Place the mixing valve motor onto the mixing valve. Use the supplied mounting screw, locking washer, and washer to attach the mixing valve motor to the mixing valve.
7) Push the mixing valve knob onto the mixing valve motor so that it indicates the B side is closed.
Mounting
Left Hand MountingValve is mounted to the Left of the Boiler
Supply (Red)
Return (Blue)
“KV” Label
BS
BR
Boiler
Right Hand MountingValve is mounted to the Right of the Boiler
Supply (Red)
Return (Blue)
“KV” Label
BS
BR
Boiler
See electrical installation on next page.
Power supply: 24V~50/60Hz
Motor speed: 150 sec./90°
Torque: 10Nm
Technical
AB A
B
B
A
B
A
B
A
Instructions for installationMixing Valve Motor for 1-1/2" & 2" Valves
L658150 March 24, 2010
1) Turn mixing valve handle so that the mixing valve is closed. Remove the mixing valve handle and indication gauge.
Left Hand Mounting Instructions
2) Screw in the supplied pin.
3) Push in and turn the mixing valve motor knob so that the A side is closed.
4) Remove the mixing valve motor knob by pulling it out.
5) Put the supplied plastic coupling attachment (with grooves facing outward) into the back of the mixing valve motor.
6) Place the mixing valve motor onto the mixing valve. Use the supplied mounting screw, locking washer, and washer to attach the mixing valve motor to the mixing valve.
7) Push the mixing valve knob onto the mixing valve motor so that it indicates the A side is closed.
1) Connect the blue “N” wire to the common (“C”) terminal on the mixing valve controller.
2) Connect the power (“R”) leads (open and close) from the mixing valve motor to the open and close terminals on the mixing valve controller.
NOTE: • Ensure that power is off before making any electrical connection!
• If motor is opening or closing in the wrong direction during the test cycle, exchange the black and brown connections (power “R” leads).
Electrical Installation
All wiring and installation as per applicable local electrical codes!
MNblue
brown
black
B
A AB A
B
AB
AB
A
B
Instructions for installationMixing Valve Motor for 1-1/2" & 2" Valves
L658150 March 24, 2010
3-way Mounting Left of the BoilerFactory Shipped Alternative Option 1
BS
BR
BS
BR
BS
BR
BS
BR
Valve is mounted to the Left of the Boiler
Supply (Red)
Return (Blue)
Boiler
Valve is mounted to the Right of the Boiler
Supply (Red)
Return (Blue)
Boiler
Supply (Red)
Return (Blue)
Boiler
Valve is mounted to the Right of the BoilerValve is mounted to the Left of the Boiler
Supply (Red)
Return (Blue)
Boiler
closeopen
closeopen
openclose
openclose
BS
BR
BS
BR
BS
BR
BS
BR
Valve is mounted to the Left of the Boiler
Supply (Red)
Return (Blue)
Boiler
Valve is mounted to the Right of the Boiler
Supply (Red)
Return (Blue)
Boiler
Supply (Red)
Return (Blue)
Boiler
Valve is mounted to the Right of the BoilerValve is mounted to the Left of the Boiler
Supply (Red)
Return (Blue)
Boiler
closeopen
closeopen
openclose
openclose
1) Turn mixing valve handle so that the mixing valve is closed. Remove the mixing valve handle and indication gauge.
2) Screw in the supplied pin.
3) Push in and turn the mixing valve motor knob so that the A side is fully open.
(turn same direction as valve was turned)
4) Remove the mixing valve motor knob by pulling it out.
5) Put the supplied plastic coupling attachment (with grooves facing outward) into the back of the mixing valve motor.
6) Place the mixing valve motor onto the mixing valve. Use the supplied mounting screw, locking washer, and washer to attach the mixing valve motor to the mixing valve.
7) Push the mixing valve knob onto the mixing valve motor so that it indicates the B side is closed.
AB A
B
B
A
B
A
Factory Shipped & Alternative Option 1 Mounting
Instructions for installationMixing Valve Motor for 1-1/2" & 2" Valves
L658150 March 24, 2010
3-way Mounting Right of the BoilerAlternative Option 2 Alternative Option 3
BS
BR
BS
BR
BS
BR
BS
BR
Valve is mounted to the Left of the Boiler
Supply (Red)
Return (Blue)
Boiler
Valve is mounted to the Right of the Boiler
Supply (Red)
Return (Blue)
Boiler
Supply (Red)
Return (Blue)
Boiler
Valve is mounted to the Right of the BoilerValve is mounted to the Left of the Boiler
Supply (Red)
Return (Blue)
Boiler
closeopen
closeopen
openclose
openclose
BS
BR
BS
BR
BS
BR
BS
BR
Valve is mounted to the Left of the Boiler
Supply (Red)
Return (Blue)
Boiler
Valve is mounted to the Right of the Boiler
Supply (Red)
Return (Blue)
Boiler
Supply (Red)
Return (Blue)
Boiler
Valve is mounted to the Right of the BoilerValve is mounted to the Left of the Boiler
Supply (Red)
Return (Blue)
Boiler
closeopen
closeopen
openclose
openclose
1) Turn mixing valve handle so that the mixing valve is closed. Remove the mixing valve handle and indication gauge.
2) Screw in the supplied pin.
3) Push in and turn the mixing valve motor knob so that the A side is closed.
4) Remove the mixing valve motor knob by pulling it out.
5) Put the supplied plastic coupling attachment (with grooves facing outward) into the back of the mixing valve motor.
6) Place the mixing valve motor onto the mixing valve. Use the supplied mounting screw, locking washer, and washer to attach the mixing valve motor to the mixing valve.
7) Push the mixing valve knob onto the mixing valve motor so that it indicates the A side is closed.B
A AB A
B
AB
AB
A
B
Alternative Options 2 & 3 Mounting