instruction manual pas td-en.pdf · 2018. 10. 30. · tivoli model. settings 8 gu electronic long...
TRANSCRIPT
-
Instruction ManualTIVOLI PAS TD for TIVOLI
-
GU Electronic
INDEX
Specifications
1. Main Spec. ----------------------------------
2. Diagram -------------------------------------
3. Components --------------------------------
4. Exterior --------------------------------------
Settings
1. Dip Switch ----------------------------------
2. Original button -----------------------------
3. Touch ---------------------------------------
4. Key board -----------------------------------
5. OSD Menu ----------------------------------
Installation
1. Installation Diagram ------------------------
2. Installation ----------------------------------
3. Caution --------------------------------------
2
3456
7891010
161719
-
GU Electronic
Specification
1. Main spec.
1-1 Input Spec. (MULTI VIDEO INTERFACE)- 1 x Analog RGB Input (Navigation System source)- 1 x Digital RGB Input (Navigation System source)- 1 x CVBS(REAR CAMERA) Input. (Rear camera source)- 1 x CVBS(FRONT CAMERA) Input. (Front camera source)- 1 x LVDS Input. (Car Command System)
1-2 Output Spec.- 1 x LCD Output (LCD Operation)
1-3 Power Spec.- Input Power : 8VDC ~ 24VDC- Consumption Power : 12Watt, Max
1-4 Switch Input mode- Possible to switch input mode through original button
2. Features
- Display dynamic PAS(Parking assistance system)- Easy installation with plug & play Power cable
3
-
GU Electronic
Specification
3. Diagram
4
INTERFACE
Scaler(PIP)
MCU
CAR COMMAND
SYSTEMCAN
EEPROMCAN
RECEIVER
CAR TFT-LCD
REAR CAMERA
RGB+Sync
DIGITAL RGB LVDS
FRONT CAMERA
COMPOSITE
COMPOSITE
LVDSTX
RELAY
LVDSRX
LVDSTX
LVDS
REAR CAMERAPOWER
-
GU Electronic
Specification
4. Components
5
OSD cable 1EA(Code: CB-OSD10-CMX)
Power cable 1EA(Code: CB-SSTV12-PWR-CMX)
RGB NAVI cable 1EA(Code: CB-RGB7-CMX)
Touch cable(KD900) 1EA(Code: CB-LRVx51-TOUCH-CMX)
Screw 4EA(Code: GN_BT_0010)
FFC cable 1EA(Code: CB-FFC-CMX-29)
OBD cable 1EA(Code: CB-SSTV12-OBD-CMX)
-
Specification
5. Exterior
166.5mm
22mm
86mm
6GU Electronic
*Touch Connect
① Y-② X-③ Y+④ X+
① ② ③ ④
*NAVI Connect
① R DATA (Red)② G DATA (Green)③ B DATA (Blue)④ SYNC (White)⑤ GND (Black)⑥ DVB-T IR (Green)⑦ DVD IR (Orange)
① ② ③ ④ ⑤ ⑥ ⑦
*POWER Connect
1. Battery (Yellow) 2. N.C3. Rear-DET (Brown)4. Front-DET (Blue)5. CAN1-L (Green)6. CAN1-H (Orange) 7. CAN2_L (White) 8. CAN2_H (Purple)
1 15
2 16
9. FRONT-PWR (Pink)10. REAR-PWR (Red) 11. REAR-CAM (White)12. GND (Black) 13. FRONT-CAM (Yellow)14. GND (Black)15. GND (Black)16. GND (Black)
NAVIPOWER/CAN TOUCHDigital
DIP S/WIMAGE LVDS IN/OUT
PROGRAM
-
Settings
1. Dip Switch* ON : DOWN , OFF : UP
7GU Electronic
NO. Function Selection
1 NAVION : Skipping NAVI
OFF : Display
2 AV1 (DVB-T)ON : Skipping DVB-T
OFF : Display
3 AV2 (DVD)ON : Skipping DVD
OFF : Display
4 N.C
5 Touch typeON : Capacitive touchOFF : Resistive touch
6 N.C
7 N.C
8 CAR type OFF: TIVOLI
* Example
TIVOLI Model
-
Settings
8GU Electronic
Long press : Switching ModeShort Press : switching to OEM screen directly
NAVIOEM AV1 AV2
※ The screen is switched in order as the pictures below
2. Original button – Steering Wheel (Switching Mode)
Setup button – Capacitive touch model Menu button : Resistive touch model
-
9
Touch OEM screen in any mode more than 11sec. For calibration(This function can be activated only one time after switching mode)
Touch the “+” correctly
- DVB-T/DVD Control
Press Touch (Anywhere) Press Icon
DVB-T
DVD
Settings
GU Electronic
3. Touch screen – Touch calibration
-
Settings
10
5. OSD Menu※ Press “MENU” button on Key board
GU Electronic
Config - NAVI-RGB : Setup for the type of NAVI-RGB Config - DVB-T(DMB) : Setup for the type of DVB-T(DMB) Config - DVD : Setup for the type of DVDReset : Reset all value
4. OSD Key board
① MENU :Activating OSD Menu② SEL :Selection③ Up :Moving upward (Increasing value)④ Down :Moving downward (Decreasing value)
MENU SEL UP DOWN
① ② ③ ④
-
11
Settings
GU Electronic
Option• RearCam-Type : Setup for rear camera
ExtDevice - External rear cameraOEM - Original camera
• RearCam-Power : Setup for Rear VCC wire in power cableON - +12V out always (current consumption : 200mA)AUTO - +12V out in rear mode only (200mA)OFF - Power OFF
• RearCam-Det : Setup for Rear detection GEAR - By CANExtwire – by rear cam detect wire
• FrontCam-Type : Setup for front cameraExtDevice - External rear cameraOEM - Original camera
• FrontCam-Power : Setup for Front VCC wire in power cableON - +12V out always (current consumption : 200mA)AUTO - +12V out in rear mode only (200mA)OFF - Power OFF
5. OSD Menu※ Press “MENU” button on Key board
-
12
Settings
GU Electronic
5. OSD Menu※ Press “MENU” button on Key board
Option
• FrontCam-Det : Setup for front detection ExtDevice - External rear cameraOEM - Original camera
• FrontCam-RcvOpt : Selecting time of displaying Front camera before switching to RGB, DVD, OEM from Rear
• NAVI COM : Connect touch through UART ※ Necessary to get Uart protocol from Navi manufacturer
• Reset : Reset all value
-
Settings
13
- NAVI(RGB) Image / Screen
- DVD, DVBT, NAVI-AV, REAR, FRONT Image
GU Electronic
5. OSD Menu※ Press “MENU” button on Key board
-
Settings
14
- PDC ON/OFF
GU Electronic
Left Right DownUP
- Adjust the position of Parking guide line
Selecting a type of language (OSD Menu – Parking – Warning Lang)
Possible to adjust the position of line by Keypad in Horizontal / Vertical menu
※ Pressing this Horizontal / Vertical menu, The OSD screen automatically disappears. Please adjust from the parking line Screen.
Selecting a use of OPS(PDC) picture(OSD Menu – Parking – OSD Display – ON or OFF)
OPS Display - On
5. OSD Menu – Parking mode※ Press “MENU” button on Key board
- Language
-
15
- OSD
MENU Horizontal
OSDUtility
Horizontal VerticalDisplayTransparencyLanguage English
505010s30
- Utility
MENU Utility
OSDlUtility
Factory Reset CalibrationVersion
Execute CancelExecute Cancel
SSTV13KRX - 180106
• Utilityy– INTERFACE SOFTWARE
• OSD – Horizontal• OSD – Vertical• OSD – Display : Setting time for displaying OSD menu• OSD – Transparency• OSD – Language : Setting language of ODS menu
GU Electronic
Settings
5. OSD Menu※ Press “MENU” button on Key board
-
1. Installation Diagram
16GU Electronic
Installation
Head unit
Monitor
Offered Power cable
Offered Touch cable(KD900)
-
2. Installation
17GU Electronic
Installation
1. Disconnect OEM FFC cable from OEM PCB board
2. Connect the offered FFC cable to where the OEM FFC cable was disconnected
3. As picture above, Connect the opposite side of the offered FFC and the OEM FFC cable to interface board
OfferedFFC Cable
-
2. Installation
18GU Electronic
Installation
4. All cables should be passed through the hole
5. As picture above, fix the interface board by screw
-
19
Caution
• Not possible to switch mode- Check connection of OSD Key pad wire - Check CAN connection
• Display wrong size of picture- Check Dip s/w setting
• Display black screen in OEM mode- Check connection of LVDS/LCD cable
• Not possible to switch to rear screen- Check the packing setting(OSD Menu – option – RearCam-Det)
1. FAQ
• The device must not be installed in where it interferes driving(close to brake pedal, steering wheel, airbag etc.)
• LVDS cable must be connected correctly according to the manual
• Insulate the end of wire by using electrical tape
• The installation should be done by expert
• GU electronic does not take any responsibility for any problem caused by wrong installation
2. Caution
-
GU Electronic
For your better driving