instruction manual - kenwoodmanual.kenwood.com/files/b60-5188-10.pdf · this instruction manual is...
TRANSCRIPT
B60-5188-10 01 MA (K, P, M, X) 0109
AUDIO VIDEO SURROUND RECEIVER
VR-6060KRF-V8060DINSTRUCTION MANUALKENWOOD CORPORATION
About the supplied remote controlCompared to standard remote controls, the remote control supplied with this receiver has severaloperation modes. These modes enable the remote control to control other audio/video components. Inorder to effectively use the remote control it is important to read the operating instructions and obtain aproper understanding of the remote control and how to switch its operation modes (etc.).Using the remote control without completely understanding its design and how to switch the operationmodes may result in incorrect operations.
This instruction manual is for some models. Model availability and features(functions) may differ depending on the country and sales area.
•VR6060/01-08/EN 3/11/02, 8:46 PM1
2 EN
Units are designed for operation as follows.
U.S.A. and Canada ........................................... AC 120 V only
Australia ........................................................... AC 240 V only
China and Russia ............................................. AC 220 V only
Other countries .......... AC 110-120 / 220-240 V switchable*
* AC voltage selectionThe AC voltage selector switch on the rear panel is set to the voltagethat prevails in the area to which the unit is shipped. Beforeconnecting the power cord to your AC outlet, make sure that thesetting position of this switch matches your line voltage. If not, itmust be set to your voltage in accordance with the following direction.
VOLTAGE SELECTORAC 110-120V~
AC 220-240V~
Note:
Our warranty does not cover damage caused by excessive linevoltage due to improper setting of the AC voltage selector switch.
Before applying the power Caution : Read this page carefully to ensure safeoperation.
Unpacking
Unpack the unit carefully and make sure that all accessories are present.
FM indoor antenna (1) AM loop antenna (1)
RF remote antenna (1)(For VR-6060 only)
For VR-6060
Remote control unit (1) Batteries (R6/AA) (2)RC-R0816
For KRF-V8060D
Remote control unit (1) Batteries (R6/AA) (2)RC-R0725
*AC plug adaptor (2)
*Use to adapt the plug on the powercord to the shape of the wall outlet.(Accessory only for regions where useis necessary.)
If any acccessories are missing, or if the unit is damaged or fails tooperate, notify your dealer immediately. If the unit was shipped to youdirectly, notify your shipper immediately. Kenwood recommends thatyou retain the original carton and packing materials in case you need tomove or ship the unit in the future.Keep this manual handy for future reference.
AC voltage selector switch
Move switch lever tomatch your line voltagewith a small screwdriveror other pointed tool.
CAUTIONRISK OF ELECTRIC SHOCK
DO NOT OPEN
Safety precautions
WARNING :TO PREVENT FIRE OR ELECTRIC SHOCK,DO NOT EXPOSE THIS APPLIANCE TORAIN OR MOISTURE.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOTREMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTSINSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL,WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TOALERT THE USER TO THE PRESENCE OF UNINSULATED“DANGEROUS VOLTAGE” WITHIN THE PRODUCT’S EN-CLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TOCONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRI-ANGLE IS INTENDED TO ALERT THE USER TO THE PRES-ENCE OF IMPORTANT OPERATING AND MAINTENANCE(SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOM-PANYING THE APPLIANCE.
Maintenance of the unitWhen the front panel or case becomes dirty, wipe with a soft, drycloth. Do not use thinner, benzine, alcohol, etc. for these agents maycause discoloration.
In regard to contact cleanerDo not use contact cleaners because it could cause a malfunction. Bespecially careful not to use contact cleaners containing oil, for theymay deform the plastic component.
•VR6060/01-08/EN 3/11/02, 8:46 PM2
3 EN
ContentsCaution : Read the pages marked carefully to ensure
safe operation.
Before applying the power
Before applying the power .............................. 2Safety precautions ............................................. 2Unpacking .......................................................... 2How to use this manual ..................................... 4Special features ................................................. 4
Names and functions of parts ......................... 5Main Unit ........................................................... 5Remote control unit (RC-R0816) (VR-6060) .......... 6Remote control unit (RC-R0725) (KRF-V8060D) ... 7
Setting up the system ........................................ 8Connecting audio components .......................... 9Connecting video components ........................ 10Digital connections .......................................... 11Connecting video components(COMPONENT VIDEO) .................................... 12Connecting a DVD player (6-channel input) ..... 13Connecting the speakers ................................. 14Connecting the terminals ................................ 15Connecting to the AV AUX jacks ..................... 16Connecting the antennas ................................. 16Connecting the system control ....................... 17Connecting the RF antenna and externalIR Repeater (For VR-6060 only) ....................... 18Preparing the remote control .......................... 19RF remote control function (For VR-6060 only) ... 19
Preparing for surround sound ....................... 20Speaker settings .............................................. 20
Normal playback.............................................. 22Preparing for playback ..................................... 22Listening to a source component .................... 23Adjusting the sound ......................................... 23
Recording .......................................................... 25Recording audio (analog sources) ................... 25Recording video ............................................... 25Recording audio (digital sources) .................... 25
Listening to radio broadcasts ....................... 26Tuning radio stations ....................................... 26Presetting radio stations manually .................. 26Receiving preset stations ................................ 27Receiving preset stations in order (P.CALL) ... 27
Ambience effects ............................................. 28Surround modes .............................................. 28Surround play ................................................... 30DVD 6-channel playback .................................. 31Convenient functions ....................................... 32
Basic remote control operations for othercomponents ....................................................... 34
Registering setup codes for othercomponents ..................................................... 34Operating other components .......................... 35Storing the remote control code ofthe other components (For VR-6060 only) ...... 35Setup code chart (RC-R0816) (VR-6060)and (RC-R0725) (KRF-V8060D) ........................ 36CASSETTE deck, CD player & MD recorderoperations ........................................................ 37Other components’ operations ....................... 38
In case of difficulty .......................................... 40Specifications .................................................. 42
Preparations
Operations
Remote Control
AdditionalInformation
For the U.S.A.
FCC WARNINGThis equipment may generate or use radio frequency energy. Changesor modifications to this equipment may cause harmful interferenceunless the modifications are expressly approved in the instructionmanual. The user could lose the authority to operate this equipmentif an unauthorized change or modification is made.
NOTE:This equipment has been tested and found to comply with the limits fora Class B digital device, pursuant to Part 15 of the FCC Rules. Theselimits are designed to provide reasonable protection against harmfulinterference in a residential installation. This equipment may causeharmful interference to radio communications, if it is not installed andused in accordance with the instructions. However, there is no guaran-tee that interference will not occur in a particular installation. If thisequipment does cause harmful interference to radio or televisionreception, which can be determined by turning the equipment off andon, the user is encouraged to try to correct the interference by one ormore of the following measures:– – Reorient or relocate the receiving antenna.– – Increase the separation between the equipment and receiver.– – Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.– – Consult the dealer or an experienced radio / TV technician for help.
For the U.S.A.
FCC Compliance NoticeAudio-video Receiver, VR-6060These devices comply with Part 15 of FCC Rules. Operation is subjectto the following two conditions: (1) This device may not cause harmfulinterference, and (2) this device must accept any interference received,including interference that may cause undesired operation.
KENWOOD U.S.A. CORPORATION2201 East Dominguez St., Long Beach, CA 90801-5745
Telephone: 310-639-9000
For Canada
IC (Industry Canada) NoticeOperation is subject to the following two conditions: (1) this devicemay not cause interference, and (2) this device must accept anyinterference, including interference that may cause undesired operationof the device.
The term “IC:” before the certification/registration number onlysignifies that the Industry Canada technical specifications were met.
For the U.S.A.
Note to CATV system installerThis reminder is provided to call the CATV system installer's attentionto Article 820-40 of the NEC that provides guidelines for propergrounding and, in particular, specifies that the cable ground shall beconnected to the grounding system of the building, as close to thepoint of cable entry as practical.
As an ENERGY STAR® Partner, Kenwood Corpora-tion has determined that this product meets theENERGY STAR® guidelines for energy efficiency.This product can save energy. Saving energy re-
duces air pollution and lowers utility bills.
•VR6060/01-08/EN 3/11/02, 8:46 PM3
4 EN
How to use this manualThis manual is divided into four sections, Preparations, Operations,Remote Control, and Additional Information.
PreparationsShows you how to connect your audio and video components to thereceiver and prepare the surround processor.Since this receiver works with all your audio and video components, wewill guide you in setting up your system to be as easy as possible.
OperationsShows you how to operate the various functions available on thereceiver.
Remote ControlShows you how to operate other components using the remote control,as well as a detailed explanation of all remote control operations. Onceyou have registered your components with the proper setup codes, you’llbe able to operate both this receiver and your other AV components (TV,VCR, DVD player, CD player, etc.) using the remote control supplied withthis receiver.
Additional InformationShows you additional information such as “In case of difficulty” (trouble-shooting) and “Specifications”.
Before applying the power
Memory back up functionPlease note that the following items will be deleted from the unit'smemory if the power cord is disconnected from the AC outlet forapproximately 1 day.
• Power mode.• Input selector settings.• Picture output.• Speaker ON/OFF.• Volume level.• BASS, TREBLE, INPUT level.• TONE ON/OFF.• LOUDNESS ON/OFF.• Dimmer level.• MD/TAPE settings.• RF-BAND. (VR-6060 only)• Listen mode setting.• Speaker settings.
• SW RE-MIX ON/OFF.• Distance setting.• Input mode setting.• Midnight mode setting.• PRO LOGIC II mode setting.• CS II mode setting.• Broadcast band.• Frequency setting.• Preset stations.• Tuning mode.• DSP mode.• ACTIVE EQ mode.• SPEAKER EQ mode.
Special featuresTrue home theater soundThis receiver incorporates a wide variety of surround modes to bring youmaximum enjoyment from your video software. Select a surround mode accord-ing to your equipment or the software you are going to play and enjoy! •
Dolby Digital and Dolby Digital EXThe DOLBY DIGITAL mode lets you enjoy full digital surround fromsoftware processed in the Dolby Digital format. Dolby Digital providesup to 5.1 channels of independent digital audio for better sound qualityand more powerful presence than conventional Dolby Surround.As for Dolby Digital EX, it creates six full-bandwidth output channelsfrom the 5.1 channel sources. This is done using a matrix decoder thatderives three surround channels from the two in the original recording.For best results, Dolby Digital EX should be used with movie sound-tracks recorded with Dolby Digital Surround EX.
Dolby PRO LOGIC qDOLBY PRO LOGIC II, whilst totally compatible with its predecessorPRO LOGIC, provides greater advantages in surround sound. It allowsthe user to enjoy the conventional stereo or Dolby Surround with aconvincing “5.1 like” presentation. PRO LOGIC II offers special fea-tures for controlling the overall spatial, dimensionality and frontal soundfield imaging. PRO LOGIC II produces an impressive surround soundfrom video software marked and three-dimensionalspace from music CD. When listening to music, you will be able to enjoythe experience of sheer STEREO surround sound.
DTS-ESThe DTS-ES (Digital Theater System-Extended Surround) is a 6.1-channelDiscrete Surround format which is extended to DTS-ES Discrete 6.1,DTS-Matrix 6.1 and DTS NEO:6. It is a 6.1 channel expanded from 5.1surround which includes an additional surround center channel developedwithin surround left and surround right. DTS-ES will be able to producethe original sound recorded similar to the theatrical effects.In the DTS-ES mode, the 5.1 or 6.1 channel digital input from a DTS CD,LD or DVD disc (carrying the “DTS” or “DTS-ES” marking) can beplayed in Digital Surround.Important:When a DTS disc is played on a CD, LD or DVD player, noise may beoutput from the analog output. It is recommended that you connect thedigital output of the player to the digital input of this unit.
Multi channel surround sound(SRS Circle Surround q )SRS Circle Surround II™ improves on its predecessor CS-5.1™ result-ing in the CS-6.1™ system, enabling you to listen to realistic, multi-channel, surround sound playback from a stereo source or conventionalsurround-encoded video source. You already enjoy listening to Dolbydigital sound/DTS multi-channel sound with your multi-speakers. Nowyou can listen to audio CDs, MDs, Broadcast and Home Theater usingyour multi-speakers. You will discover a new type of sound throughSRS Circle Surround II .
DSP surround modesThe DSP (Digital Signal Processor) used for this receiver incorporatesa variety of high quality adjustable sound fields, like “ARENA”, “JAZZCLUB”, “THEATER”, “STADIUM” and “DISCO”. It is compatible withalmost any kind of program source.
DVD 6-channel inputIf you own a DVD player equipped with 6-channel output, this receiverallows you to obtain the full surround sound impact of DVD source materialfeaturing multi-channel encoding. Since the source signals are digital andeach channel is input independently, the resulting ambience is far superiorto what can be achieved with conventional surround sound systems.
ACTIVE EQACTIVE EQ mode will produce a more dynamic sound quality in anycondition. You can enjoy a more impressive sound effect when ACTIVEEQ is turned on during Dolby Digital and DTS playback.
SPEAKER EQThe SPEAKER EQ function will automatically detect the various featuresof each speaker and effectively creates a stereoscopic sound effect.
Remote controlThis remote control has two kinds of signal.
Universal IR (InfraRed) remote controlIn addition to the basic receiver, the remote control supplied with thisreceiver can also operate almost all of your remote controllable audioand video components. Just follow the simple setup procedure toregister the components you have connected.
RF remote signal (For VR-6060 only)You can operate the receiver by sending RF remote signal from theremote control. The controllable range of the remote control is notinfluenced by surroundings such as distance or an obstruction.
•VR6060/01-08/EN 3/11/02, 8:46 PM4
5 EN
L
SL S SB SR
C R
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs DSP MODE
DTSMATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CS II A B CLIPAUTO DETECT
AUTOMEMORYSTEREOTUNED
SWLFE
LOUDNESS SPEAKER EQ ACTIVE EQ DSP STEREO INPUT MODE DIMMER
SOUND TONE SETUP
BAND AUTO MEMORY
MULTI CONTROL LISTEN MODETUNER
MD/TAPEVIDEO 3VIDEO 2VIDEO 1
PHONOCD/DVD
DSP
DTS
CS II
DOLBY DIGITAL
SPEAKER EQ
ACTIVE EQ
STANDBY
ON/STANDBY
A SPEAKERS B
POWER
PHONES
DOWN
MUTE
AV AUX
S VIDEO VIDEO L-AUDIO-R
UP
VOLUME CONTROL
STANDBYPOWER
ON/STANDBY
DVD/6CH
-ON –OFF
F ULL DIGITALD E C O D I N G
Display
Speaker selection indicatorsInput channel indicatorsOutput channel indicators
AUTO indicatorMEMORY indicator
STEREO indicator
TUNED indicator
Names and functions of parts
Frequency displayInput displayPreset channel displaySurround mode display
Speakerindicators
1 POWER ON/OFF key
(For KRF-V8060D) )Use to turn the main power ON/OFF.
2 ON/STANDBY ( ) key
(For KRF-V8060D) )Use to turn the power ON/STANDBY whenthe POWER is turned ON.STANDBY indicator
2 POWER ON/STANDBY ( ) key
(For VR-6060) )Use to turn the power ON/STANDBY.STANDBY indicator
3 A SPEAKERS B keys ™Use to turn the A/B speakers ON/OFF.
4 LOUDNESS key ¢Use to switch the status of LOUDNESS.
5 SPEAKER EQ key ¢Use to select SPEAKER EQ’s setting.
6 Surround indicators
DSP indicator ºLights when the receiver is in the DSP mode.SPEAKER EQ indicator ¢Lights when the receiver is in the SPEAKEREQ mode.ACTIVE EQ indicator ¢Lights when the receiver is in the ACTIVE EQmode.DOLBY DIGITAL indicator ºLights when the receiver is in the DolbyDigital mode.
Main unit
& BAND key §Use to select the broadcast band.
* AUTO key §Use to select the auto or manual tuningmode.
( TONE key £Use to switch the status of TONE control.
) MEMORY key §Use to store radio stations in the presetmemory.
¡ SETUP key )Use to select the speakers' settings etc.
™ MMMMM/????? keys )Use for selection adjustments during SOUND,SETUP and PRESET CHANNEL functions.
£ MULTI CONTROL knob )Use to control a variety of settings.
¢ LISTEN MODE knob ºUse to select the listening mode.
∞ AV AUX (S VIDEO, VIDEO, AUDIO L/R)
jacks ^§ AV AUX key ^
Use to switch the input to AV AUX.
DTS indicator ºLights when the receiver is in the DTS mode.CS q indicator ºLights when the receiver is in the CIRCLESURROUND II mode.
7 ACTIVE EQ key ¢Use to select ACTIVE EQ’s setting.
8 DSP key ºUse to select any of the DSP mode.
9 STEREO key ¤Use to switch the listen mode to STEREO.
0 INPUT MODE key 8Use to switch between the full auto, digitaland analog inputs.
! DIMMER key
Use to select the REC MODE. ∞Use to adjust the brightness of the display.
‹@ VOLUME CONTROL knob £# MUTE key ¢
Use to temporarily mute the sound.$ PHONES jack ¢
Use for headphone listening.% Input Selector keys £
(DVD/6CH, CD/DVD, PHONO, TUNER,
VIDEO 1, VIDEO 2, VIDEO 3, MD/TAPE)
Use to select input sources.^ SOUND key ¤
Use to adjust the sound quality and the ambi-ence effects.
MUTEindicator
CLIPindicator
Input modeindicators
Listen modeindicators
For VR-6060
Standby modeWhile the standby indicator is lit, a small amount of power is suppliedto the system to back up the memory. This is called standby mode.Under the condition, the system can be turned ON by remote controlunit.
Connection at POWER ON/OFF key (for KRF-V8060D)The power in this equipment will not be completely cut off from the ACwall outlet when the main switch is turned OFF.
•VR6060/01-08/EN 3/11/02, 8:47 PM5
6 EN
! PAGE %/fi keyUse to operate the DVD component.
@ OSD keyUse to operate the DVD component.
# TUNING 1/¡ keys §Use to operate the tuner mode.If CD, MD or TAPE is selected as the inputsource, these keys function as search keys.
$ DISC SKIP keyIf CD is selected as the input source, this keyfunctions as the multi-CD player disc skip key.A/B keyIf TAPE is selected as the input source, this isA and B deck of a double cassette deck.
% DISC SEL keyUse to operate other components.INPUT SEL keyUse to operate other components.
^ INPUT SELECTOR keys (DVD/6CH, CD/DVD,PHONO, TUNER, VIDEO 1, VIDEO 2, VIDEO 3,MD/TAPE, AV AUX)Use to select the input sources. £
& LOUDNESS key ¢Use to switch the status of LOUDNESS.
* SOURCE ( ) keyUse to turn the other components ON/OFF.
( POWER ( ) key )Use to turn the receiver ON/OFF.
) RECEIVER keyUse to return to the operation of the receiver.
¡ LISTEN MODE %/fi keys ºUse to select the listening mode.
™ ACTIVE EQ key ¢Use to select ACTIVE EQ’s setting.
£ SPEAKER EQ key ¢Use to select SPEAKER EQ’s setting.
¢ DSP MODE key ºUse to select any of the DSP mode.
∞ MUTE key ¢Use to temporarily mute the sound.
§ VOLUME +/- keys £Use to adjust the receiver volume.
¶ MENU keyUse to operate other components.SOUND key ¤Use to adjust the sound quality and the ambi-ence effects.
• RETURN keyUse to operate other components.
ª 2 keyUse to operate other components.FLIP keyUse to operate other components.
º 3/8 keyIf CD is selected as the input source, this keyfunctions as the play/pause key.If MD or TAPE key is selected as input source,this key functions as the play key.BAND key §Use to select the broadcast band.
⁄ 7 keyIf CD, MD, or TAPE is selected as the inputsource, this key functions as the stop key.AUTO key §Use to select the auto or manual tuningmode.
¤ DIMMER key ‹Use to adjust the brightness of the display.8 keyUse to operate other components.
‹ BASS BOOST key £Use to select the maximum adjustment set-ting for the low frequency range.
› TONE key £Use to switch the status of TONE control.
1 LCD (Liquid Crystal Display)2 LEARN key fi
Use to memorize the operation of the otherremote controls.
3 REMOTE MODE keys (DVD, CBL, DSS/SAT, VCR, TV, OTHERS) ›Use to select the components registered atthe respective input.
4 Numeric keys ›Provide functions identical to those of theoriginal remote control supplied with the com-ponent you are controlling.
5 INPUT MODE key 8Use to switch between the full auto, digitaland analog inputs.
6 STEREO key ¤Use to switch the listen mode to STEREO.
7 CH +/- keysUse to select the channels.¢ DVD 4 keysWhen in DVD player operations, these keysfunction as skip keys.
8 TV CONTROL keysUse when in TV operation.
9 TOP MENU keyUse to operate the DVD component.SET UP key )Use to select the speakers’ settings etc.
0 JoystickENTERUse to operate other components.MULTI CONTROL C/D )Use to control a variety of settings.Use to operate other components.P.CALL 4 /DOWN 2 and P.CALL/UP ¢3 ¶Use for selection adjustments during SOUND,SET UP and PRESET channel functions.
Names and functions of parts
Remote control unit (RC-R0816) (VR-6060)This remote control unit can be use not only for Kenwood products but also for other non-Kenwood products by setting the appropriate manufacturer’ssetup codes. fl
If the name of a function is different on
the receiver and on the remote control,
the name of the remote control key in
this manual is indicated in parentheses.
3
2
1
(
)
¡
™
£
¢
∞
§
¶
•
ª
º
⁄
¤
‹
›
4
5
6
7
8
0
@
#
$
%
^
&
9
*
!PAGE
P.CALL 4 /DOWN
P.CALL/UP ¢
TUNING
+
TOP MENUSET UP
MENUSOUND
TV CONTROL
VOL.
VOLUME
+
- - INPUT SEL
+
-CH
DVD
VCR TV OTHERS
RECEIVER
SOURCE POWER
ACTIVE EQ
OSD RETURN
DISC SEL DISC SKIP
FLIP BAND
INPUT SEL A/B AUTO 8
DVD/6CH CD/DVD PHONO TUNER
VIDEO 1 VIDEO 2 MD/TAPE
LOUDNESS TONE BASS BOOST
MUTE
DVD
ENTER
INPUT SELECTOR
MULTICONTROL
¢
4
1 ¡ 2 6
7 DIMMER
™ £
™
1
4
7
+10
2
5
8
0
3
6
9
+100
REMOTE MODE
LISTEN MODE
DSP MODESTEREOINPUT MODE
SPEAKER EQ
™
VIDEO 3
AV AUX
LEARN
CBL DSS/SAT
•VR6060/01-08/EN 3/11/02, 8:47 PM6
7 EN
1
&
*
(
)
¡
™
£
¢
∞
§
¶
•
ª
º
⁄
¤
2
3
4
5
6
8
0
!
@
#
$
%
7
^
9
P.CALL 4 /DOWN
P.CALL/UP ¢
TUNING
+
TOP MENUSET UP
MENUSOUND
TV CONTROL
VOL.
VOLUME
+
- - INPUT SEL
+
-CH
DVD
VCR TV OTHERS
RECEIVER
SOURCE POWER
ACTIVE EQ
OSD RETURN
DISC SEL DISC SKIP
FLIP BAND
INPUT SEL A/B AUTO 8
DVD/6CH CD/DVD PHONO TUNER
VIDEO 1 VIDEO 2 MD/TAPE
LOUDNESS TONE BASS BOOST
MUTE
DVD
ENTER
INPUT SELECTOR
MULTICONTROL
¢
4
1 ¡ 2 6
7 DIMMER
™ £
™
1
4
7
+10
2
5
8
0
3
6
9
+100
REMOTE MODE
LISTEN MODE
DSP MODESTEREOINPUT MODE
SPEAKER EQ
™
VIDEO 3
AV AUX
PAGE
CBL DSS/SAT
! TUNING 1/¡ keys §Use to operate the tuner mode.If CD, MD or TAPE is selected as the inputsource, these keys function as search keys.
@ DISC SKIP keyIf CD is selected as the input source, this keyfunctions as the multi-CD player disc skip key.A/B keyIf TAPE is selected as the input source, this isA and B deck of a double cassette deck.
# DISC SEL keyUse to operate other components.INPUT SEL keyUse to operate other components.
$ INPUT SELECTOR keys (DVD/6CH, CD/DVD,PHONO, TUNER, VIDEO 1, VIDEO 2, VIDEO 3,MD/TAPE, AV AUX)Use to select the input sources. £
% LOUDNESS key ¢Use to switch the status of LOUDNESS.
^ SOURCE ( ) keyUse to turn the other components ON/OFF.
& POWER ( ) key )Use to turn the receiver ON/OFF.
* RECEIVER keyUse to return to the operation of the receiver.
( LISTEN MODE %/fi keys ºUse to select the listening mode.
) ACTIVE EQ key ¢Use to select ACTIVE EQ’s setting.
¡ SPEAKER EQ key ¢Use to select SPEAKER EQ’s setting.
™ DSP MODE key ºUse to select any of the DSP MODE.
£ MUTE key ¢Use to temporarily mute the sound.
¢ VOLUME +/- keys £Use to adjust the receiver volume.
∞ MENU keyUse to operate other components.SOUND key ¤Use to adjust the sound quality and the ambi-ence effects.
§ RETURN keyUse to operate other components.
¶ 2 keyUse to operate other components.FLIP keyUse to operate other components.
• 3/8 keyIf CD is selected as the input source, this keyfunctions as the play/pause key.If MD or TAPE key is selected as input source,this key functions as the play key.BAND key §Use to select the broadcast band.
ª 7 keyIf CD, MD, or TAPE is selected as the inputsource, this key functions as the stop key.AUTO key §Use to select the auto or manual tuningmode.
º DIMMER key ‹Use to adjust the brightness of the display.8 keyUse to operate other components.
⁄ BASS BOOST key £Use to select the maximum adjustment set-ting for the low frequency range.
¤ TONE key £Use to switch the status of TONE control.
1 REMOTE MODE keys (DVD, CBL, DSS/SAT, VCR, TV, OTHERS) ›Use to select the components registered atthe respective input.
2 Numeric keys ›Provide functions identical to those of theoriginal remote control supplied with the com-ponent you are controlling.
3 INPUT MODE key 8Use to switch between the full auto, digitaland analog inputs.
4 STEREO key ¤Use to switch the listen mode to STEREO.
5 CH +/- keysUse to select the channels.¢ DVD 4 keysWhen in DVD player operations, these keysfunction as skip keys.
6 TV CONTROL keysUse when in TV operation.
7 TOP MENU keyUse to operate the DVD component.SET UP key )Use to select the speakers’ settings etc.
8 JoystickENTERUse to operate other components.MULTI CONTROL C/D )Use to control a variety of settings.Use to operate other components.P.CALL 4 /DOWN 2 and P.CALL/UP ¢3 ¶Use for selection adjustments during SOUND,SET UP and PRESET channel functions.
9 PAGE %/fi keyUse to operate the DVD component.
0 OSD keyUse to operate the DVD component.
Names and functions of parts
Remote control unit (RC-R0725) (KRF-V8060D)This remote control unit can be used not only for Kenwood products but also for other non-Kenwood products by setting the appropriate manufacturer’ssetup codes. fl
If the name of a function is different on
the receiver and on the remote control,
the name of the remote control key in
this manual is indicated in parentheses.
•VR6060/01-08/EN 3/11/02, 8:47 PM7
8 EN
Make connections as shown in the following pages.When connecting the related system components, be sureto refer to the instruction manuals supplied with the compo-nents you are connecting.Do not connect the power cord to a wall outlet until allconnections are completed.
Notes1. Be sure to insert all connection cords securely. If their connections are
imperfect, sound may not be produced or there will be noise inference.2. Be sure to remove the power cord from the AC outlet before plugging
or unplugging any connection cords. Plugging/unplugging connectioncords without disconnecting the power cord can cause malfunctionsand may damage the unit.
3. Do not connect power cords from components whose power con-sumption is larger than what is indicated on the AC outlet at the rearof this unit.
Analog connectionsAudio connections are made using RCA pin cords. These cables transferstereo audio signal in an “analog” form. This means the audio signalcorresponds to the actual audio of two channels. These cables usuallyhave 2 plugs on each end, one red for the right channel and one white forthe left channel. These cables are usually packed together with thesource unit, or are available at your local electronics retailer.
Microcomputer malfunctionIf operation is not possible or an erroneous display appears, eventhough all connections have been made properly, reset the micro-computer referring to “In case of difficulty”. ‚
CAUTIONBe sure to adhere to the following, or proper ventilation will be
blocked causing damage or fire hazard.
• Do not place any objects impairing heat radiation onto the top of theunit.
• Leave some space around the unit (from the largest outsidedimension including projection) equal to or greater than, shownbelow.Top panel : 50 cm Side panel : 10 cm Back panel : 10 cm
Setting up the system
Input mode settingsCD/DVD, VIDEO 2, VIDEO 3 and DVD/6CH inputs each include jacksfor digital audio input and analog audio input.You must select beforehand which type of input is to be used for eachconnected component.The initial factory settings for audio signal playback for CD/DVD,
DVD/6CH, VIDEO 2 and VIDEO 3 are full auto.
To use the analog audio input for playback instead (if, for example, youhave connected a VCR to the VIDEO 2 or VIDEO 3 input), you must setthe input mode for the corresponding input to the analog mode.After completing connections and turning on the receiver, follow thesteps below.
INPUT MODE
Input Selector
1 Use the Input Selector keys to select CD/DVD, VIDEO 2, VIDEO 3
or DVD/6CH.
2 Press the INPUT MODE key.
Each press switches the setting as follows:
In DTS play mode
1 FULL AUTO (digital input, analog input)2 DIGITAL MANUAL (digital input)
In CD/DVD, VIDEO 2, VIDEO 3 or DVD/6CH play mode
1 FULL AUTO (digital input, analog input)2 DIGITAL MANUAL (digital input)3 6CH INPUT (DVD/6CH input)4 ANALOG (analog input)
Digital input:
Select this setting to play digital signals from a DVD, CD, or LDplayer.
Analog input:
Select this setting to play analog signals from a cassette deck, VCR,or record player.
Auto detect:
In “FULL AUTO” mode (AUTO DETECT indicator light up), thereceiver detects the digital or analog input signals automatically.Priority is given to digital signal during input mode selection. Thereceiver will select the input mode and listening mode automaticallyduring playback to match the type of input signal (Dolby Digital,PCM, DTS) and the speaker setting. The OPTICAL and COAXIALindicator on the display will light up when digital signal is detected.If the input signal is analog, the ANALOG indicator will light up.To keep the receiver set to the currently selected listening mode,use the INPUT MODE key to select “DIGITAL MANUAL” (manualsound). However, even when this setting is selected, there may becases in which the listening mode is selected automatically tomatch a Dolby Digital source signal depending on the combinationof listening mode and source signal.If the INPUT MODE key is pressed quickly, sound may not beproduced. Press the INPUT MODE key again.
•VR6060/01-08/EN 3/11/02, 8:47 PM8
9 EN
IN IN REC OUT PLAY IN
GND CD/DVD MD/TAPEPHONO
R
L
R
L
Connecting audio components
Record player
Setting up the system
To AC wall outlet
Cassette deck orMD recorder
CD or DVD player
SYSTEM CONTROLjacks &
Shape of AC outlets
U.S.A. and Canada
Other countries
IN
OUT
OUT
OUT
Australia
Moving coil (MC) cartridgerecord player cannot be useddirectly from the receiver unit.It can only be used whenanother equalizer amplifier isconnected.
•VR6060/09-20/EN 3/11/02, 8:48 PM9
10 EN
VIDEO 1 VIDEO 2 VIDEO 3
PLAY INPLAY INPLAY INREC OUTOUTVIDEO
INVIDEO
INVIDEO
DVDIN
INVIDEO
MONITOROUT
VIDEO
S VIDEOOUT
VIDEO
S VIDEOIN
VIDEO
S VIDEOIN
VIDEO
S VIDEOIN
VIDEODVDIN
MONITOROUT
S VIDEO
Connecting video components
INVideo deck
Monitor TV
A video component with digital audio outputs should be connected to the VIDEO 2 or VIDEO 3 jacks.
VideoIN/OUT
INVideo inputs and outputs(Yellow RCA pin cords)
OUT
OUTAudio inputsand outputs
S Video jacks
Video inputs(Yellow RCA pin cords)
About the S VIDEOjacks
S VIDEO
Use the S VIDEO jacks tomake connections tovideo components withS VIDEO IN/OUT jacks.
• If you use the S VIDEOjacks to connect your videoplayback components, besure to use the S VIDEOjacks when connectingyour monitor and videorecording components.
VIDEOIN
OUT OUT
AudioIN/OUT
Setting up the system
OUT OUTDVD player or LD player
DVD player or LD player
•VR6060/09-20/EN 3/11/02, 8:48 PM10
11 EN
COAXIAL OPTICAL OPTICALVIDEO 3CD/DVD
DIGITAL IN
DVD/6CH
VIDEO2
Digital connectionsThe digital in jacks can accept DTS, Dolby Digital, or PCM signals. Connect components capable of outputting DTS, Dolby Digital, or standard PCM (CD)format digital signals.If you have connected any digital components to the receiver, be sure to read the “Input mode settings” section carefully. 8
COAXIALDIGITALOUT(AUDIO)
Connect the video signal and digitalaudio signals to the VIDEO 3 jacks.(See “Connecting video components”.)
0
DOLBY DIGITAL RFOUT (AUDIO)
OPTICAL DIGITAL OUT (AUDIO)
LD playerPCM OUT
Component with DTS,Dolby Digital, or PCMOPTICAL DIGITAL OUT
Setting up the system
To connect an LD player with a DIGITAL RF OUT, connect the LD player to the KENWOOD RF digital demodulator (DEM-9991D).
Next, connect the DIGITAL OUT jacks of the demodulator to the DIGITAL IN jacks of the receiver.
Connect the video signal and analog audio signals to the VIDEO 2 or VIDEO 3 jacks. (See “Connecting video components”.)
RF digitaldemodulator(DEM-9991D)(sold separately)
CD or DVD player
OPTICAL DIGITAL OUT (AUDIO)
Optical fiber cable
Component with DTS,Dolby Digital, or PCMCOAXIAL DIGITAL OUT
Opticalfiber cable
COAXIAL DIGITAL OUT (AUDIO)
Connect the video signal and analogaudio signals to the VIDEO 2 jacks.(See “Connecting video components”.)
0
•VR6060/09-20/EN 3/11/02, 8:48 PM11
12 EN
Setting up the system
Connecting video components (COMPONENT VIDEO)If you have connected the receiver to a video component with COMPONENT jacks, you can get a better picture quality than by connecting to the S-VIDEOjacks.
When connecting the TV to the COMPONENT jacks, be sure to connect all the other components to the COMPONENT jacks.
Monitor TV(with component jacks)
Video Recorder, DVD Recorder,Satellite Cable Tuner & Game Player(with component jacks)
DVD player (with component jacks)
• Connect to the VIDEO cord.
DVDIN
VIDEO3IN
MONITOR OUT
CRCBY
CRCBY
CR INCB IN
Y IN
CR OUTCB OUT
Y OUT
CR OUTCB OUT
Y OUT
COMPONENT VIDEO
•VR6060/09-20/EN 3/11/02, 8:48 PM12
13 EN
DVD/6CH INPUTFRONT SURROUND
COAXIAL OPTICAL OPTICALVIDEO 3CD/DVD
DVD/6CH
VIDEO2
SUB WOOFER
CENTERPLAY INPLAY IN
DIGITAL IN
VIDEO 2 VIDEO 3
OUTVIDEO
INVIDEO
INVIDEO
DVDIN
INVIDEO
MONITOROUT
VIDEO
S VIDEOIN
VIDEO
S VIDEOIN
VIDEODVDIN
MONITOROUT
S VIDEO
VIDEO
Connecting a DVD player (6-channel input)If you have connected a DVD player to the receiver with digital connection, be sure to read the “Input mode settings” section carefully. 8
FRONTOUT L/R
S VIDEOOUT
COAXIALDIGITAL OUT(AUDIO)
DVD player
S VIDEO cord
SURROUNDOUT L/R
VIDEO OUT(Yellow RCApin cord)
CENTEROUT
SUBWOOFEROUT
Setting up the system
•VR6060/09-20/EN 3/11/02, 8:48 PM13
14 EN
GREENWHITERED
R L CENTERFRONT A
-
+
+ +--
FRONT B
R L
GRAY
SURROUND
R L
-
+
BLUE
PURPLE
SURROUND BACK/SUBWOOFER
SURROUND BACK
SUBWOOFER
PRE OUT
Right
Front Speakers A
Right
CenterSpeaker
Surround Speakers(Be sure to connect bothsurround speakers)
Power amplifier
Left
Surround Back/SubwooferUse this terminal if you wish toconnect to a Surround Backspeaker with the SETUP of“6ch AMP SB” or to connectto a subwoofer speaker withthe SETUP of “6ch AMP SW”.
Connecting the speakers
Setting up the system
Right
Front Speakers B
SurroundBack
Poweredsubwoofer
Left
Left
•VR6060/09-20/EN 3/11/02, 8:48 PM14
15 EN
Setting up the system
Connecting the terminals
1 Strip coating. 2 Loosen.
3 Insert. 4 Secure.
1 Strip coating. 2 Push the lever.
3 Insert the cord. 4 Return the lever.
Connection of banana plugs (For the U.S.A. and Canada)1 Secure. 2 Insert.
• Sound will not be heard if the speaker terminal is not fully secured.
• Never short circuit the + and – speaker cords.• If the left and right speakers are connected inversely or the speaker
cords are connected with reversed polarity, the sound will beunnatural with ambiguous acoustic imaging. Be sure to connect thespeakers correctly.
Speaker impedanceAfter confirming the speaker impedance indications printed on therear panel of the receiver, connect speakers with matching imped-ance ratings. Using speakers with a rated impedance other than thatindicated on the rear panel of the receiver could result in malfunctionsor damage to the speakers or receiver.
Speaker placement
Front speakers : Place at the front left and right of the listeningposition. Front speakers are required for all surround modes.Center speaker : Place front and center. This speaker stabilizes thesound image and helps recreate sound motion. Required for surroundplayback.Surround speakers : Place at the direct left and right, or slightlybehind, the listening position at even heights, approximately 1 meterabove the ears of the listeners. These speakers recreate soundmotion and atmosphere. Required for surround playback.Subwoofer : Reproduces powerful deep bass sounds.Surround back speaker : Place the speaker directly at the rear of thelistening position. The optimum position depends mainly on the roomcondition.
• Although the ideal surround system consists of all the speakerslisted above, if you don't have a center speaker or a subwoofer, youcan divide those signals between the available speakers in thespeaker settings steps to obtain the best possible surround repro-duction from the speakers you have available. )
Channel space switching(Except for the U.S.A., Canada, U.K., and Australia)
The space between radio channels has been set to the one thatprevails in the area to which the system is shipped. However, if thecurrent channel space setting does not match the setting in the areawhere the system is to be used, for instance when you move fromarea 1 or area 2 shown in the following table or vice versa, properreception of AM/FM broadcasts cannot be expected. In this case,change the channel space setting in accordance with your area byreferring to the following table.
Area CHANNELSpace Frequency
1 U.S.A., Canada and South FM: 100 kHzAmerican countries AM: 10 kHz
2 Other countries FM: 50 kHzAM: 9 kHz
75
50us AM 9kHz FM50kHz
75us AM 10kHz FM100kHz
DE-EMPHASISCHANNEL SPACE
DE-EMPHASISCHANNEL SPACE
50us AM 9kHz FM50kHz
75us AM 10kHz FM100kHz
Turn the power OFF by pressing the POWER key before moving theswitch level. Move switch lever to match your area with a smallscrewdriver or other pointed tool, then turn the power on again.
Center speaker
SubwooferFrontspeaker
Surroundspeaker
Surroundback speaker
Listeningposition
•VR6060/09-20/EN 3/11/02, 8:49 PM15
16 EN
S VIDEO OUT
S VIDEO cord
VIDEO OUT
AUDIO OUT
Connecting the antennasAM loop antennaThe supplied loop antenna is for use indoors. Place it as far as possiblefrom the receiver, TV set, speaker cords and power cord, and adjust thedirection for best reception.
AM antenna terminal connections1 Push lever. 2 Insert cord. 3 Release lever.
FM indoor antennaThe supplied indoor antenna is for temporary use only. For stable signalreception we recommend using an outdoor antenna. Disconnect theindoor antenna when you connect one outdoors.
FM antenna terminal connectionsInsert cord.
FM outdoor antennaLead the 75Ω coaxial cable connected to the FM outdoor antenna into theroom and connect it to the FM 75Ω terminal.
FM75
GND
AM
ANTENNA
AM loop antenna
FM indoor antenna
Use an antennaadaptor(Commerciallyavailable)
Attach to the stand
Setting up the system
Connecting to the AV AUX jacksThe AV AUX jacks are convenient for connection of video componentssuch as a camcorder or a video game.
S VIDEO VIDEO L-AUDIO-R
AV AUX
• To select the source connected to the AV AUX jacks press AV
AUX key. £• When you connect the audio source such as the MD player, you
do not need to connect the video cable.
• When you connect the unit and the component with the S
VIDEO cord, you can get better picture quality.
Camcorder, other VCR,video game, digital camera,or portable MD player
FM outdoor antenna
•VR6060/09-20/EN 3/11/02, 8:49 PM16
17 EN
Connecting the system control
Connecting system control cords after connecting a KENWOOD
audio component system lets you take advantage of convenient
system control operations.
This unit is compatible only with the [SL-16] mode. The system
control operation is not available if the unit is connected in the
[XS8], [XS], or [XR] connection mode.
If your component has the mode select switch, set the connected
components to the [SL16] mode.
SYSTEM CONTROL
• You may connect the system control cord to either the up or downjack.
EXAMPLE: [SL16] mode connections
The underlined portion represents the setting of the system controlmode.
[SL16] Receiver
[SL16] [XS] [XS8] [XR]Cassette deckor MD recorder
[SL16] [XS] [XS8] CD player
[XS] Record player
• In order to take advantage of the system control operations, thecomponents must be connected to the correct jacks. To use a CDplayer it must be connected to the CD jacks. To use a cassette deck(or MD recorder) it must be connected to the MD/TAPE jacks. Whenusing more than one CD player (etc.) only the one connected to thespecified jacks may be connected for system control.
• Some CD players and cassette decks are not compatible with the[SL16] system control mode. Do not make system connections withequipment that is not [SL16] compatible.
• Some MD players are not system control compatible. You cannotmake system control connections to this kind of equipment.
Notes1. [SL16] equipment cannot be combined with [XR], [XS], and [XS8]
equipment for system operations. If your equipment consists ofthis kind of combination, please do not connect any system con-trol cords. Even without system control cords, normal operationscan be carried out without effecting performance.
2. Do not connect system control cords to any components otherthan those specified by KENWOOD. It may cause a malfunctionand damage your equipment.
3. Be sure the system control plugs are inserted all the way in to thesystem control terminals.
SYSTEMCONTROLcord
SYSTEM CONTROL OPERATIONSRemote Control
Lets you operate this unit with the system remote supplied with thereceiver.
Automatic Operation
When you start playback from a source component, the input selectoron this unit switches to that component automatically.
Synchronized Recording
Lets you synchronize recording with the start of playback whenrecording from CD, MD or analog discs.
Registering setup codes for KENWOOD audio componentsIf you own remote controllable KENWOOD audio components thatare not compatible with system control, registering the setup codeenables you to control those components using the remote controlsupplied with this unit (without connecting system control cords). Toregister setup codes for your remote controllable KENWOOD audiocomponents, see “Registering setup codes for other components”.
fl
Setting up the system
SYSTEM CONTROLcord
•VR6060/09-20/EN 3/11/02, 8:49 PM17
18 EN
Connecting the RF antenna and external IR Repeater (For VR-6060 only)
The remote control for this receiver has the RF (radio frequency) and IR (infrared rays) transmission function. IR repeaters enables you to controlcomponents located in cabinets or behind glass doors. You can enjoy a wider remote control signal range by placing the RF antenna and IR repeater awayfrom the receiver.
KENWOOD components (except DVD player): System control &Other components: (Registering setup codes) IR REPEATER fl
Setting up the system
RF REMOTE ANTENNA
OUT
IR REPEATER
RF antenna
Monitor TV
IR repeaters
Shape of plug to be connected.
IR REPEATER OUT
Mono Mini Plug
IR OUT SPECIFICATION:
Terminal IR REPEATER
OUT
To Tip Signal
To Sleeve Ground
Sleeve
Tip
(For RF Transmitter, select either1. RF REMOTE Band 1, or2. RF REMOTE Band 2)
Connecting IR repeater1 Connect the IR repeater to the device as described in the
repeater’s manual.
2 Connect the IR repeater cable(s) to the IR REPEATER OUT
jack(s).
Notes• IR repeaters send a signal similar to the device’s own remote control.
Xantech repeaters (models 282-00, 286-00, or 283-00) are compatiblewith your new audio-video receiver.
Connecting the RF remote antenna1 Insert the jack of the provided RF remote antenna into the
RF REMOTE ANTENNA jack.
2 Place the antenna wire vertically and fix it.
• Place the antenna away from the metallic panel.
•VR6060/09-20/EN 3/11/02, 8:49 PM18
19 EN
Preparing the remote control
Loading the batteries1 Remove the cover. 2 Insert the batteries.
3 Close the cover.
• Insert two AA-size (R6) batteries as indicated by the polarity markings.
RF remote control function (For VR-6060 only)
The remote control has the RF remote function in addition to the IRremote function. The VR-6060 can receive the remote control com-mands even when they are installed in a position where the IR remotesignal can hardly access, for example inside a cabinet. The receiver is notequipped with the RF remote bi-directional communication function. Thebi-directional communication is available only when using the IR remotefunction with equipments other than the receiver.
Changing the RF transmission frequencyThe RF remote function may be unavailable due to radio wave cross talk,etc. In this case, the transmission frequency can be changed.
To change the RF remote transmission frequency:
1 Change the RF switch setting.
After changing the RF frequency of remote control, be also sure tochange that of the receiver.
2 Change the receiver’s RF reception frequency.• Press and hold the SETUP key on the front panel of the receiver
for more than 2 seconds.Each time you press the SETUP key, the RF reception frequencychanges as follows:
1 “RF REMOTE BAND 1”
2 “RF REMOTE BAND 2”
3 “RF REMOTE OFF”
• Select the same number as the position number of the RFswitch of the remote control.
Setting up the system
Remote control operationWhen the STANDBY indicator is lit, the power turns ON when you pressthe POWER or SOURCE key on the remote control. When thepower comes ON, press the key you want to operate.
Operating other component range (IR Transmitter)
6 m
SOURCE
Operating receiver range (RF Transmitter)
POWER
• The remote control signal received by main unit IR and RF signals.• When pressing more than one remote control key successively, press the
keys securely by leaving an interval of 1 second or more between keys.
Notes1. The supplied batteries may have shorter lives than ordinary batteries
due to use during operation checks.2. When the remote-controllable distance gets shorter than before, re-
place both batteries with new ones.3. Placing the remote sensor in direct sunlight, or in direct light from a
high frequency fluorescent lamp may cause a malfunction.In such a case, change the location of the system installation to pre-vent malfunction.
Important notesHere is list of adjustment which can maximize the operation of
your remote control. For optimal operation of the remote control:
1 Aim the remote control toward the room where the receiver islocated.
2 Do not position the receiver and remote control near metal (suchas heat ducts). Metal can absorb RF signals.
3 Make sure the batteries in the remote control are fully charged.Weak batteries will affect the range of the remote control.
4 When there is an obstruction around other equipments that sendsignal from the remote control, the control distance of the RFremote signal will be short.
Note• The tests for range limits of the remote control and the receiver are
conducted in open-air distance test. Actual distance of the signal willbe based on the construction of the building where the unit is beingused in as well as other factors such as outside interference.
IR Transmitter
RF Remote antenna
RF Transmitter
10 m
Remote sensor
•VR6060/09-20/EN 3/11/02, 8:49 PM19
20 EN
Preparing for surround sound
Speaker settingsTo enable you to obtain optimum enjoyment from the receiver’s listeningmodes, make sure to complete the speaker settings (subwoofer, front,center, and surround speakers) as described below.
SETUP MULTI CONTROL
POWER ON/OFF(KRF-V8060D)
POWER
SET UPJoystick(MULTI CONTROL5 /∞,DOWN2 / UP3)
POWER ON/STANDBY
(VR-6060)
ON/STANDBY (KRF-V8060D)
1 Turn on the power to this receiver by pressing the POWERON/STANDBY (for VR-6060) or POWER ON/OFF and ON/STANDBY (for KRF-V8060D) key or POWER key.
2 Press the SETUP key to enter the SETUP mode.The Surround Back and Subwoofer speaker output selections aredisplayed as follows:
1 6ch AMP SB
2 6ch AMP SW
Use the MULTI CONTROL knob or Joystick (5/∞) to select the speakers.Press the SETUP key to proceed to the next SET UP selection.
Use MMMMM/????? keys or Joystick (2/3) for the following displays.1 SP SETUP
2 TEST TONE
3 SP DISTANCE
4 DISP MODE
5 EXIT
The flow of the SET UP is as follows:
SP SETUP TEST TONE SP DISTANCE EXITDISP MODE
Front Left
Center
Front Right
Surround Right
Surround Back
Surround Left
Subwoofer
Display Selector
Display Listen
Subwoofer
Front
Center
Surround
SurroundBack
SurroundMix
SubwooferRe-mix
T. TONEMANUAL
T. TONEAUTO
LCR
SR
SLSB
SW
L
C
R
SR
SL
SW
SB
3 Select a speaker system.
1 Select the SP SETUP and press the SETUP key again so
that the subwoofer setting indication “SUBW ON” appears.
L
SL S SB SR
C R
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.ACTIVE EQ.DSP MODE
DTS.MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII A B CLIPAUTO DETECT THX
AUTO
RDSRTY
MEMOSTEREOTUNED
Surround EXSW
LFE
2 Use the MULTI CONTROL knob or Joystick (5/∞) to select
the appropriate subwoofer setting.
1 SUBW ON : Subwoofer setting mode to the receiver isON.
2 SUBW OFF : Subwoofer setting mode to the receiver isOFF.
• The initial setting is “SUBW ON”.• When the setting “SUBW OFF” is selected, the front speakers
are automatically set to “FRNT LARGE” and the procedure skipsto step 6.Before step 6, press the SETUP key to accept the setting.
• When subwoofer output sound is required, select “FRNTNORMAL”, or select both “FRNT LARGE” and “SW RE-MIX ON”.
• After setting SW (subwoofer) from OFF to ON, 6ch AMP setupdisplay will appear to enable you to re-select either SW or SB fromthe surround back or subwoofer speaker terminal.
3 Press the MMMMM key or Joystick (3) to accept the setting.
• The front speakers setting indication “FRNT” appears.
L
SL S SB SR
C R
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.ACTIVE EQ.DSP MODE
DTS.MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII A B CLIPAUTO DETECT THX
AUTO
RDSRTY
MEMOSTEREOTUNED
Surround EXSW
LFE
4 Use the MULTI CONTROL knob or Joystick (5/∞) to select
the appropriate front speakers setting.
1 FRNT LARGE : Large front speakers are connectedto the receiver.
2 FRNT NORMAL : Average size front speakers are con-nected to the receiver.
• For “FRNT LARGE” selection, no sound will be heard fromsubwoofer speaker even when it is set to ON. However, if youselect “SW RE-MIX ON” when subwoofer is selected, you willbe able to hear sound from the subwoofer.When in STEREO mode, the sound goes directly to frontspeaker.
5 Press the MMMMM key or Joystick (3) to accept the setting.
• The center speaker setting indication “CNTR” appears.
6 Use the MULTI CONTROL knob or Joystick (5/∞) to select
the appropriate center speaker setting.
If you selected “LARGE” as the front speakers setting,
1 CNTR LARGE : A large center speaker is connectedto the receiver.
2 CNTR NORMAL : An average size center speaker isconnected to the receiver.
3 CNTR OFF : Center speaker setting mode to thereceiver is OFF.
If you selected “NORMAL” as the front speakers setting,
1 CNTR ON : Center speaker setting mode to the re-ceiver is ON.
2 CNTR OFF : Center speaker setting mode to the re-ceiver is OFF.
7 Press the MMMMM key or Joystick (3) again to accept the setting.
• The surround speaker setting indication “SURR” appears.
8 Use the MULTI CONTROL knob or Joystick (5/∞) to select
the appropriate surround speaker setting.
If you selected “LARGE” as the center speaker setting,
1 SURR LARGE : Large surround speakers are con-nected to the receiver.
2 SURR NORMAL : Average size surround speakers areconnected to the receiver.
3 SURR OFF : Surround speaker setting mode tothe receiver is OFF.
•VR6060/09-20/EN 3/11/02, 8:50 PM20
21 EN
Preparing for surround sound
If you selected other than “LARGE” as the center speaker setting,
1 SURR ON : Surround speaker setting mode to the re-ceiver is ON.
2 SURR OFF : Surround speaker setting mode to the re-ceiver is OFF.
• When the setting “SURR OFF” is selected, the procedure skipsto step #.
9 Press the MMMMM key or Joystick (3) again to accept the setting.
• The surround speaker setting indication “SB” appears.
0 Use the MULTI CONTROL knob or Joystick (5/∞) to select
appropriate surround back speaker setting.
If you selected “LARGE” as the surround speaker setting,
1 SB NORMAL : Average size surround back speaker isconnected to the receiver.
2 SB LARGE : Large surround back speaker isconnected to the receiver.
3 SB OFF : Surround back speaker setting mode tothe receiver is OFF.
L
SL S SB SR
C R
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.ACTIVE EQ.DSP MODE
DTS.MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII A B CLIPAUTO DETECT THX
AUTO
RDSRTY
MEMOSTEREOTUNED
Surround EXSW
LFE
If you selected “NORMAL” as the surround speaker setting,
1 SB ON : Surround back speaker setting mode to thereceiver is ON.
2 SB OFF : Surround back speaker setting mode to thereceiver is OFF.
• After setting SB (surround back) from OFF to ON, 6ch AMP setupdisplay will appear to enable you to re-select either SW or SB fromthe surround back or subwoofer speaker terminal.
! Press the MMMMM key or Joystick (3) again to accept the setting
and “SURR:MIX” appears.
• Surr:mix is when the SL and SR speakers signals are mixed toproduce sound from the surround back speaker which wouldenable the listener to enjoy sound coming from the back.
L
SL S SB SR
C R
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.ACTIVE EQ.DSP MODE
DTS.MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII A B CLIPAUTO DETECT THX
AUTO
RDSRTY
MEMOSTEREOTUNED
Surround EXSW
LFE
@ Use the MULTI CONTROL knob or Joystick (5/∞) to select
the following.
1 SURR:MIX ON : Surround mix setting mode to thereceiver is ON.
2 SURR:MIX OFF : Surround mix setting mode to thereceiver is OFF.
• If surround back speaker is turned OFF, SURR:MIX setting is notvisible and the procedure skips to step #.
# Press the MMMMM key or Joystick (3) again to accept the setting.
• The subwoofer remix setting indication “SW RE-MIX” appears.
$ Use the MULTI CONTROL knob or Joystick (5/∞) to select
the appropriate subwoofer re-mix setting.
1 SW RE-MIX ON : Subwoofer re-mix setting mode tothe receiver is ON.
2 SW RE-MIX OFF : Subwoofer re-mix setting mode tothe receiver is OFF.
• If subwoofer is turned OFF, subwoofer re-mix setting is not visible.
% Press the SETUP key again to return to the main setup displays.
• The receiver enters the speaker volume level adjustment mode.• In steps 4 and 5, indications appear only for the selected
channels of the speakers that require adjusting.
4Adjust the speaker volume level.
From your usual listening position, adjust the volume levels. Thevolume levels from each speaker should be the same.
1 Press the MMMMM/????? keys or Joystick (2/3) to select TEST TONE.
2 Press the SETUP key for the following displays:
1 T.TONE AUTO
2 T.TONE MANUAL
3 The selection of AUTO/MANUAL TEST TONE is done by the
MULTI CONTROL knob or Joystick (5/∞).
Press the SETUP key again to begin TEST TONE.
Use the MULTI CONTROL knob or Joystick (5/∞) to adjust
the volume level of the test tone output from the speaker
channel to be adjusted.
For AUTO selection, the first test tone is heard from the front left
speaker for 2.5 seconds. The next test tone is heard from the
speakers in the following sequence for 2 seconds each.
LEFT CNTR RIGHT
SRSBSLSUBW
The channel indication blinks while the test tone is being output.
L
SL S SB SR
C R
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.ACTIVE EQ.DSP MODE
DTS.MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII A B CLIPAUTO DETECT THX
AUTO
RDSRTY
MEMOSTEREOTUNED
Surround EXSW
LFE
• If you change the volume level settings for the speakers whilelistening to music, the settings referred to on this page are alsochanged. ¤
• If the speaker setting selects are OFF, the speaker level settingsare reset.
For MANUAL selection, press the MMMMM/????? keys or Joystick (2/3)
each time to select the speaker channel.
4 Press the SETUP key again.
• The test tone is turned off and return to the main setup displays.
5 Input the distance to the speakers.
1 Press the MMMMM/????? keys or Joystick (2/3) to select the SP
DISTANCE on setup displays and press the SETUP key again.
2 Measure the distance from the listening position to each of
the speakers.
Jot down the distance to each of the speakers.
Distance to Front left speaker (L) : ____ feet (meters)Distance to Center speaker (C) : ____ feet (meters)Distance to Front right speaker (R) : ____ feet (meters)Distance to Surround right (SR) : ____ feet (meters)Distance to Surround back (SB) : ____ feet (meters)Distance to Surround left (SL) : ____ feet (meters)Distance to Subwoofer (SW) : ____ feet (meters)
3 Use the MMMMM/????? keys or Joystick (2/3) to select the speakers
and the MULTI CONTROL knob or Joystick (5/∞) to adjust
the distance to the front speakers.
The speaker indicator to be adjusted blinks.
L
SL S SB SR
C R
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.ACTIVE EQ.DSP MODE
DTS.MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII A B CLIPAUTO DETECT THX
AUTO
RDSRTY
MEMOSTEREOTUNED
Surround EXSW
LFE
• The allowable setting range is 1 to 30 feet (0.3 to 9.0 m),adjustable in 1 foot (0.3 m) increments.
Indication in feet Indication in meters
Continued to next page.
•VR6060/21-28/EN 3/11/02, 8:50 PM21
22 EN
4 Repeat steps 3 to input the distance for each of the speakers.
5 Press the SETUP key again to return to main setup displays.
• The speakers you have selected should appear on the display.Confirm that all the speakers have been correctly selected.
6 Select the display mode.
1 Press the MMMMM/????? key or Joystick (2/3) to select the DISP MODE.
2 Press the SETUP key for the following displays:
1 DISP SELECTOR : Displays the current input selector.2 DISP LISTEN : Displays the current listen mode.
3 Use the MULTI CONTROL knob or Joystick (5/∞) to select
the display mode.
SL S SB SR
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.ACTIVE EQ.DSP MODE
DTS.MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII A B CLIPAUTO DETECT THX
AUTO
RDSRTY
MEMOSTEREOTUNED
Surround EX
LFEL C RSW
4 Press the SETUP key again to accept the setting.
5 Use the MMMMM key or Joystick (3) to select EXIT.
L C R
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.ACTIVE EQ.DSP MODE
DTS.MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII A B CLIPAUTO DETECT THX
AUTO
RDSRTY
MEMOSTEREOTUNED
Surround EXSW
LFE
SL S SB SR
6 Press the SETUP key to exit the SET UP mode.
Input level adjustment (analog sources only)If the input level of an analog source signal is too high, the CLIP indicatorwill blink to indicate the source signal. Adjust the input level.
L
SL S SB SR
C R
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMACTIVDSP MA B CLIP
AUTO DETECT
SWLFE
CLIPCLIP
1 Use the Input Selector keys to select the source of which the
input level you want to adjust.
• You can store a separate input level for each input source.
2 Press the SOUND and MMMMM/????? keys or Joystick (2/3) repeatedly
until the “INPUT” indication appears.
3 Use the MULTI CONTROL knob or Joystick (5/∞) to adjust the
input level.
L
SL S SB SR
C R
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.ACTIVE EQ.DSP MODE
DTS.MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII A B CLIPAUTO DETECT THX
AUTO
RDSRTY
MEMOSTEREOTUNED
Surround EXSW
LFE
• The adjustment mode is displayed for approximately 8 seconds.• The input level may be adjusted to any one of three settings:
0dB, -3dB, and -6dB. (The initial setting is 0dB.)
4 Press the SOUND key again to return to the input indication.
Preparing for surround sound
Preparing for playbackSome preparatory steps are needed before starting playback.
INPUT MODE
MD/TAPEPOWER ON/OFF(KRF-V8060D)
A SPEAKERS B
POWER ON/STANDBY
(VR-6060)
ON/STANDBY (KRF-V8060D)
Turning on the receiver1 Turn on the power to the related components.
2 Turn on the power to this receiver by pressing the POWER
ON/STANDBY key (for VR-6060) or POWER ON/OFF and
ON/STANDBY (for KRF-V8060D) key.
Selecting the input modeIf you have selected a component connected to the CD/DVD, VIDEO 2,
VIDEO 3 or DVD/6CH jacks, make sure that the input mode setting iscorrect for the type of audio signal to be used. 8
Selecting MD/TAPESelect the source name corresponding to the component connectedto the MD/TAPE jacks. The initial factory setting is “TAPE”. Tochange the source to “MD”, follow the steps below:
Hold down the MD/TAPE key for more than 2 seconds.
• The source indication changes to “MD”.• To return to the original indication, repeat the above procedure.
Selecting the speaker systemPress the A SPEAKERS B key to select the speaker system to be
used.
A ON : Sound from the speakers connected to the SPEAKERS A
terminals on the rear panel.B ON : Sound from the speakers connected to the SPEAKERS B
terminals on the rear panel. No sound will be heard fromthe subwoofer.
A+B ON : Sound from both the speakers connected to theSPEAKERS A and B terminals on the rear panel.
A+B OFF : No sound from the speakers. Use this setting whenlistening with headphones for stereo sound in all playbackmodes. The display segments are different depending onthe type of input signal.
The indicator for the speakersyou want to use should be lit.
L
SL S SB SR
C R
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMACTIVDSP MA B CLIP
AUTO DETECT
SWLFE
• Selecting “6CH INPUT” by pressing the INPUT MODE key, whereby“DVD/6CH” is the input source will cause SPEAKERS A to be selectedautomatically.
Normal playback
•VR6060/21-28/EN 3/11/02, 8:51 PM22
23 EN
Listening to a source component
VOLUME CONTROL
VOLUME /
INPUT SELECTOR
Input Selector AV AUX
1 Use the Input Selector and AV AUX keys to select thesource you want to listen to.
Selecting a source using each key.
1 “DVD/6CH”
2 “CD/DVD”
3 “PHONO”
4 “TUNER”
5 “VIDEO 1”
6 “VIDEO 2”
7 “VIDEO 3”
8 “MD/TAPE”
9 “AV AUX”
2 Start playback from the selected source.
3 Use the VOLUME CONTROL knob or VOLUME +/- keys toadjust the volume.
Normal playback
Adjusting the sound
LOUDNESSTONE
BASS BOOST
TONE
VOLUME CONTROL
MUTE
A SPEAKERS BSPEAKER EQ ACTIVE EQ
PHONES LOUDNESS
MULTI CONTROL
VOLUME /
POWER
SPEAKER EQACTIVE EQ
MUTE
Joystick(MULTI CONTROL5 /∞,DOWN2 / UP3)
Adjusting the TONEYou can adjust the sound quality when the receiver is in the PCM stereoand analog stereo mode.
1 Press the TONE key to select the TONE mode.
2 Use the MULTI CONTROL knob or Joystick (5/∞) to select
TONE ON/OFF.
L
SL S SB SR
C R
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.ACTIVE EQ.DSP MODE
DTS.MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII A B CLIPAUTO DETECT THX
AUTO
RDSRTY
MEMOSTEREOTUNED
Surround EXSW
LFE
3 When in TONE ON selection, press the TONE key for the
following displays.
BASS : Select this to adjust the low frequency range.TREBLE : Select this to adjust the high frequency range.
4 Use the MULTI CONTROL knob or Joystick (5/∞) to adjust the
sound quality.
L
SL S SB SR
C R
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.ACTIVE EQ.DSP MODE
DTS.MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII A B CLIPAUTO DETECT THX
AUTO
RDSRTY
MEMOSTEREOTUNED
Surround EXSW
LFE
• The bass and treble levels are adjustable from -10 to +10 in 2 stepincrements.
• The adjustment item is displayed for approximately 8 seconds.
Once-touch low frequency emphasis (BASS BOOST)(remote control only)You can adjust the sound quality when the receiver is in the PCM stereoand analog stereo modes.
Press the BASS BOOST key.
• Press the key once to select the maximum (+10) low frequencyemphasis setting.
• This key does not function when the receiver is in the sound qualityor ambience effects adjustment mode.
Switching back to the previous settingPress the BASS BOOST key again.
•VR6060/21-28/EN 3/11/02, 8:51 PM23
24 EN
Adjusting the LOUDNESS modeYou can adjust the Loudness function which controls the low volumesettings to maintain the music's richness. The adjustment can be madewhen the receiver is in the PCM stereo and analog stereo mode.
Press the LOUDNESS key to turn the LOUDNESS setting ON.
To cancelPress the LOUDNESS key again so that the “LOUDNESS”
indicator goes off.
Muting the soundThe MUTE key lets you mute the sound of the speakers.
Press the MUTE key.
L
SL S SB SR
C R
MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.ACTIVE EQ.DSP MODE DA B CLIP
AUTO DETECT
SWLFE
SP
Blinks
To cancelPress the MUTE key again so that the “MUTE” indicator goes off.
• MUTE ON can also be deactivated by turning the VOLUMECONTROL knob or pressing VOLUME +/– keys.
ACTIVE EQ modeYou can enjoy a more impressive sound effect when ACTIVE EQ isturned ON during Dolby Digital and DTS playback and, when in PCM andanalog stereo mode.
Press the ACTIVE EQ key for the following selections;
1 ACTIVE EQ MUSIC : Effective when listening to music.(The ACTIVE EQ indicator lights up.)
2 ACTIVE EQ CINEMA : Effective when watching a movie.(The ACTIVE EQ indicator lights up.)
3 ACTIVE EQ TV : Effective when watching TV.(The ACTIVE EQ indicator lights up.)
4 ACTIVE EQ OFF : The ACTIVE EQ function is turned OFF.(The ACTIVE EQ indicator goes off.)
• “ACTIVE EQ” will scroll from right to left.• When ACTIVE EQ and SPEAKER EQ are OFF and ACTIVE EQ
(MUSIC) is turned ON, SPEAKER EQ (SMALL) will turn ONautomatically.
• ACTIVE EQ function will not be available when REC MODE, AUTOTUNING or PRESET MEMORY is ON, and during 96kHz LPCM playback.
SPEAKER EQ modeSPEAKER EQ’s function will automatically detect the various features ofeach speaker and effectively creates a stereoscopic sound effect.
Press the SPEAKER EQ key to switch the following setting;
1 SPEAKER EQ SMALL : To select a small size speaker.(The SPEAKER EQ indicator lights up.)
2 SPEAKER EQ NORMAL : To select an average size speaker.(The SPEAKER EQ indicator lights up.)
3 SPEAKER EQ LARGE : To select a large size speaker.(The SPEAKER EQ indicator lights up.)
4 SPEAKER EQ OFF : The SPEAKER EQ function is turnedOFF.(The SPEAKER EQ indicator goes off.)
• “SPEAKER EQ” will scroll from right to left.• SPEAKER EQ cannot be turned OFF when ACTIVE EQ is turned ON.• SPEAKER EQ function will not be available when REC MODE, AUTO
TUNING or PRESET MEMORY is ON, and during 96kHz LPCMplayback.
Normal playback
Listening with headphones1 Press the A and B Speaker keys so that the speaker indicator
goes off.
Make sure the SPEAKERSindicators are turned off.
SL S SB SR
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.ACTIVE EQ.DSP MODE DA B CLIP
AUTO DETECT
LFE
• If you turn off all of the speakers when in surround mode, the surroundmode will be canceled as well, resulting in stereo playback.
2 Connect headphones to the PHONES jack.
PHONES
3 Use the VOLUME CONTROL knob or VOLUME +/– keys to
adjust the volume.
•VR6060/21-28/EN 3/11/02, 8:51 PM24
25 EN
Recording audio (analog sources)
MD/TAPE
Recording a music source1 Use the Input Selector keys to select the source (other than “MD/
TAPE”) you want to record.
2 Set the MD or TAPE recorder to record.
3 Start playback, then start recording.
Recording video1 Use the Input selector keys to select the video source (other than
“VIDEO 1”) you want to record.
2 Set the video deck connected to VIDEO 1 to record.
• Select the REC MODE to record a digital input source.
3 Start playback, then start recording.
• Recording may not be normal for some video software. This is dueto the copy guard condition. ‚
Recording audio (digital sources)Switch on the REC MODE to record a digital input source.Usually use the AUTO REC MODE to record audio input sources. Whenthe digital mode changes during recording in the AUTO REC MODE, theaudio input source may be interrupted momentarily.
Recording music in AUTO REC or MANUAL REC mode
Input Selector
DIMMER
1 Use the Input Selector keys to select the source (CD/DVD,
DVD/6CH, VIDEO 2, VIDEO 3) you want to record.
2 Set the MD or TAPE recorder to record.
Recording
3 Press and hold the DIMMER key for more than 2 seconds to
select the AUTO REC or MANUAL REC mode.
1 REC MODE off : The digital input record mode isswitched off.
2 AUTO REC mode : The digital input signals (DTS, DolbyDigital, or PCM) are identified auto-matically and converted into stereosignals that are ready for recording.
3 MANUAL REC mode : The input signal type at the momentthis mode is selected is held through-out this mode.
For AUTO REC mode :
L
S SBSL SR
C R
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.ACTIVE EQ.DSP MODE
DTS.MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII A B CLIPAUTO DETECT THX
AUTO
RDSRTY
MEMOSTEREOTUNED
Surround EXSW
LFE
↓
L
S SB
C R
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.ACTIVE EQ.DSP MODE
DTS.MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII A B CLIPAUTO DETECT THX
AUTO
RDSRTY
MEMOSTEREOTUNED
Surround EXSW
LFE
SL SR
For MANUAL REC mode :
L
SL S SB SR
C RSWLFE
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.ACTIVE EQ.DSP MODE
DTS.MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII A B CLIPAUTO DETECT THX
AUTO
RDSRTY
MEMOSTEREOTUNED
Surround EX
↓
L
SL S SB SR
C RSWLFE
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.ACTIVE EQ.DSP MODE
DTS.MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII A B CLIPAUTO DETECT THX
AUTO
RDSRTY
MEMOSTEREOTUNED
Surround EX
4 Start playback, then start recording.
• If the audio reproduction stops in the middle due to change in theinput signals, etc., press the DIMMER key.
•VR6060/21-28/EN 3/11/02, 8:51 PM25
26 EN
Presetting radio stations manually
MULTI CONTROL
MEMORYTUNER
1 Tune to the station you want to store.
2 Press the MEMORY key while receiving the station.
Blinks for 5 seconds Lights for 5 seconds
L
SL S SB SR
C RSWLFE
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.ACTIVE EQ.DSP MODE
DTS.MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII A B CLIPAUTO DETECT THX
AUTO
RDSRTY
STEREOTUNED
Surround EX
MEMORY
Proceed to step 3 within 5 seconds.
(If more than 5 seconds elapse, press the MEMORY key again).
3Use the MULTI CONTROL knob or Joystick (5/∞) to selectone of the station presets (1 – 40).
4 Press the MEMORY key again to confirm the setting.
• Repeat steps 1, 2, 3, and 4 to store as many stations asnecessary.
• If you store a station at a previously used preset, the old station willbe replaced by the new one.
Listening to radio broadcasts
The receiver can store up to 40 stations in the memory and recall themby one-touch operation.
Tuning radio stations
BAND MULTI CONTROL
TUNER AUTO
Joystick(MULTI CONTROL5 /∞)
AUTO
TUNING 1/¡
TUNERBAND
1Use the TUNER key to select the tuner.
2Use the BAND key to select the desired broadcast band.
Each press switches the band.
L
SL S SB SR
C RSWLFE
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.ACTIVE EQ.DSP MODE
DTS.MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII A B CLIPAUTO DETECT THX
AUTO
RDSRTY
MEMOSTEREOTUNED
Surround EX
3Use the AUTO key to select the desired tuning method.
Each press switches the tuning method to either auto or manual
tuning.
“AUTO” indicator lights up in the display.ICAL 6CH INPUT
XIAL ANALOG 96kHzfs
CINEMA EQ.ACTIVE EQ.DSP MODE
DTS.MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII
AUTO DETECT THX RDSRTY
MEMOSTEREOTUNED
Surround EX
AUTO
• Normally, set to “AUTO” (auto tuning). If the radio waves are weakand there is a lot of interference, switch to manual tuning. (Withmanual tuning, stereo broadcasts will be received in monaural.)
4Use the MULTI CONTROL knob or Joystick (5/∞), or TUNING1 / ¡ keys to select the station.“STEREO” lights when a broadcast is being received in stereo.
CAL 6CH INPUT
XIAL ANALOG 96kHzfs
CINEMA EQ.ACTIVE EQ.DSP MODE
DTS.MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII
AUTO DETECT THX
AUTO
RDSRTY
MEMO
Surround EX
STEREOTUNED
“TUNED” is displayed when a station is received.
Auto tuning : The next station is tuned automatically.Manual tuning : Turn the knob or use the Joystick (5/∞) to
select the desired station.
•VR6060/21-28/EN 3/11/02, 8:52 PM26
27 EN
Listening to radio broadcasts
Receiving preset stations
TUNER
Numeric keys
1 Press the TUNER key to select tuner as the source.
2 Enter the number of the preset station you want to receive(up to “40”).
Press the numeric keys in the following order:
For “15”, press 0,5For “20”, press 0,0,)
• If you make a mistake entering a two digit number, press the +10
key repeatedly to return to the original display and start again.
L
SL S SB SR
C RSWLFE
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.ACTIVE EQ.DSP MODE
DTS.MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII A B CLIPAUTO DETECT THX
AUTO
RDSRTY
MEMOSTEREOTUNED
Surround EX
Receiving preset stations in order (P.CALL)
Joystick(P.CALL 4/¢)
TUNER
1 Press the TUNER key to select the tuner as the source.
2Use the Joystick to adjust the P.CALL 4/ ¢ direction toselect the desired station.
• Each time you push the Joystick, another preset station is receivedin order.
Pushing the Joystick to P.CALL ¢ does the following:
Pushing the Joystick to P.CALL 4 does the following:
Holding the Joystick on ¢ or 4 direction, lets you skip
through the presets, receiving each preset station at 0.5 second
intervals.
•VR6060/21-28/EN 3/11/02, 8:52 PM27
28 EN
Ambience effects
This receiver is equipped with listening modes that allow
you to enjoy an enhanced sonic ambience with a variety of
video sources.
In order to obtain the optimum effect from the surround
modes, make sure to input the proper speaker settings
beforehand. )
Surround modes
Dolby DigitalThe Dolby Digital surround format lets you enjoy up to 5.1 channelsof digital surround sound from Dolby Digital program sources (such asLaserdisc or DVD software marked ). Compared with previ-ous Dolby surround, Dolby Digital provides even better sound quality,greater spatial accuracy, and improved dynamic range.
NoteAlthough a full set of speakers (front left, right, and center, surroundleft and right, and a subwoofer) is required for true 5.1 channel DolbyDigital surround sound, this receiver lets you enjoy Dolby Digital (andDolby Surround) program sources, even if you connect only the frontspeakers.
* LFE = Low Frequency Effects. This channel delivers separatenon-directional bass signals to the subwoofer for more dynamicdeep bass sound effects.Although only Dolby Digital soundtracks incorporate a separatelow frequency channel, connecting a subwoofer will also improvedeep bass performance in the other surround modes.The indication “LFE” appears in the display when a signal isbeing input for this channel.
“DTS”, “DTS-ES Extended Surround”and “Neo:6” are trademarks of DigitalTheater Systems, Inc.
Manufactured under license from Dolby Laboratories. “Dolby”, “ProLogic” and the double-D symbol are trademarks of DolbyLaboratories.
“Circle Surround II and the ® symbol are trademarks of SRS Labs,
Inc. Circle Surround II technology is incorporated under license from SRSLabs, Inc”.
Dolby Digital EXDolby Digital EX is an extension of Dolby Digital technology, DolbyDigital EX creates six full-bandwidth output channels from 6.1-channelsources. This is done using a matrix decoder that derives threesurround channels from the two in the original recording.This is achieved by using three different surround signals, surround left,surround right and surround back, each driving its own array ofspeakers. Think of it as adding a center channel for the rear speakers,which give more diffuse and natural surround effect, even if youwanted the ability to completely encircle the audience with sound,positioning sound effects exactly where they wolud be heard in real life.For best results, Dolby Digital EX should be used with movie soundtracksrecorded with Dolby Digital Surround EX which contain a digital flag thatwill automatically activate this feature. However, for titles releasedprior to late 2001, this feature has to be activated manually.
NoteAlthough a full set of speakers (front left, right, and center, surroundleft and right, surround back and a subwoofer) is required for true 6.1channel Dolby Digital Surround EX sound, this receiver lets you enjoyDolby Digital (and Dolby Surround) program sources, even if youconnect only the front speakers.
* LFE = Low Frequency Effects. This channel delivers separatenon-directional bass signals to the subwoofer for more dynamicdeep bass sound effects.Although only Dolby Digital soundtracks incorporate a separatelow frequency channel, connecting a subwoofer will also improvedeep bass performance in the other surround modes.The indication “LFE” appears in the display when a signal isbeing input for this channel.
Dolby PRO LOGIC IIDolby Pro Logic II was designed specifically to provide a new sense ofspatiality, directionality and articulation of sounds from Dolby Surroundencoded sources (such as video and Laserdisc software marked
). This is achieved with an intelligent, built-in feedbacklogic design, a matrix surround decoding and the decoding of stereo, fullbandwidth surround outputs. The PRO LOGIC II modes programmed intothis receiver are “MOVIE”, “MUSIC” and “PRO LOGIC”. The “MOVIE”mode of the PRO LOGIC II has preset characteristics to produce acalibrated, high-level surround sound playback while the “MUSIC” modehas user-adjustable characteristics to offer the three optional controls, like“Dimension”, “Center Width” and “Panorama” modes to allow optimiza-tion of the soundfields as desired. The “Dimension” control allows theuser to gradually adjust the soundfield either towards the front or towardsthe rear; the “Center Width” control allows various adjustment of the left-center-right speakers’ balance; the “Panaroma” mode extends the frontstereo image to include the surround speakers for an exciting “wrap-around” effect with side wall imaging.
* Optional in this mode.
Center speaker
Subwoofer (SW)*
Surroundspeakers (L, R)
Front speakers (L, R)
Center speaker
Subwoofer (SW)
Surroundspeakers (L, R)
Front speakers (L, R)
* Optional in this mode.
Center speaker
Subwoofer (SW)*
Surroundspeakers (L, R) Surround
back speaker
Front speakers (L, R)
•VR6060/21-28/EN 3/11/02, 8:52 PM28
29 EN
Ambience effects
Multi channel surround sound (SRS Circle Surround II)SRS Circle Surround II™ improves on its predecessor CS-5.1™resulting in the CS-6.1™ system, enabling you to listen to realistic,multi-channel, surround sound playback from a stereo source orconventional surround-encoded video source. You already enjoylistening to Dolby Digital sound/DTS multi-channel sound with yourmulti-speakers. Now you can listen to audio CDs, MDs, Broadcast andHome Theater using your multi-speakers. You will discover a newtype of sound through SRS Circle Surround II.The CS system dramatically reduces storage space requirements formulti-channel content. It creates a listening environment that placesthe listener “inside” music performances, and dramatically improvesboth hi-fi audio and conventional surround-encoded video material.The CS decoder also includes the SRS technologies Focus™ andTruBass™. Focus electronically raises the sound stage from thespeaker location to an optimal position. TruBass creates deep, richbass in small speaker systems without the need for a subwoofer.
DVD 6-channel mode
Using a DVD player or the like equipped with six (5.1) output channelsand the receiver, you can enjoy multi-channel encoded DVD sourcematerial in all its splendor. Since the source signals are digital andeach channel is input independently, the resulting sound quality,sense of spaciousness, and dynamic range are superb.
* LFE = Low Frequency Effects. This channel delivers separate non-directional bass singnals to the subwoofer for more dynamic deepbass sound effects.
DSP modeThe DSP mode lets you add the atmosphere of a live concert or hall toalmost any type of program source. These modes are particularly effectivewhen used with stereo program sources, like CD, television, and FM radio.You might enjoy trying the ARENA, JAZZ CLUB, THEATER, STADIUM orDISCO mode the next time you watch a concert or sporting event!
What's DSP?DSP stands for Digital Signal Processor.The way a sound is heard in an actual environment depends on avariety of different factors. One of the most important is reverberation(the act of decaying elements of sound echoing in various places).The DSP modes produce the feeling of presence by using the DSP tocreate reverberation, without spoiling the sound quality of the originalsignal.
DTS-ESThe DTS-ES (Digital Theater System-Extended Surround) represents6.1-channel Discrete Surround format, expanding upon 5.1 surround.DTS-ES format is a 6.1 channel sound system for movie theaters thatincludes as additional surround-center channel matrixed withinsurround-left and surround-right. It’s compatible on predecessor DTS5.1 system. The extra channel allows more accurate placement andsteering of sound accross the rear soundstage.The DTS-ES receiverwill be required, to experience a discrete 6.1-channel mix.The DTS-ES decoders used in home cinema systems have decodingoptions for utilizing the extra channel, in addition to processingexisting 5.1 channel surround sound :DTS-ES Discrete 6.1 and DTS-ES Matrix 6.1 add the surround backchannel audio to the DTS 5.1-channel format to improve the acousticpositioning and makes acoustic image movement more natural withthe 6.1-channel reproduction. NEO:6 is a new technology whichdecodes 2-channel signals into 6-channel signals using high-accuracydigital matrix technology. For best results, DTS-ES should be usedwith movie soundtracks recorded with DTS-ES which contain a digitalflag that will automatically activate this feature. However, for sometitles, this feature has to be activated manually.According to the signals to be played back, DTS NEO:6 uses either theNEO:CINEMA mode optimized for movie playback or the NEO:MUSICmode optimized for music playback.
* LFE = Low Frequency Effects. This channel delivers separate non-directional bass signals to the subwoofer for more dynamic deepbass sound effects.DTS has a .1 or LFE channel.The indication “LFE” appears in the display when a signal is beinginput for this channel.
Center speaker
Subwoofer (SW)
Surroundspeakers (L, R) Surround
back speaker
Front speakers (L, R)
Center speaker
Subwoofer (SW)
Surroundspeakers (L, R)
Front speakers (L, R)
Center speaker
Subwoofer (SW)*
Surroundspeakers (L, R)
Front speakers (L, R)
Center speaker
Subwoofer (SW)*
Surroundspeakers (L, R) Surround
back speaker
Front speakers (L, R)
* Optional in this mode.
•VR6060/29-34/EN 3/11/02, 8:53 PM29
30 EN
Surround playThe DTS compatible models can reproduce a CD, DVD, or LD carrying theDTS mark.DOLBY DIGITAL can be used when playing DVD or LD software bearingthe mark and DOLBY DIGITAL format digital broadcasts (etc.).DOLBY PRO LOGIC can be used when playing video, DVD, or LDsoftware bearing the mark.SRS Circle Surround II enables you to listen to multi channel sound fromthe stereo source.
INPUTSELECTOR
INPUT MODE
DSP INPUT MODE
LISTEN MODEInput Selector
DSP MODE
LISTEN MODE%/fi
Preparations• Turn ON related components.• Complete “Preparing for surround sound” (speaker settings). )• Use the Input Selector keys to select the component you wish to play
back with surround sound.• Use the INPUT MODE key to select the input mode (analog or digital)
for the source you wish to play back. 8• Noise will be produced when a DTS source is played by selecting the
analog input.
1 Start playing the video software.
2Use the LISTEN MODE knob or LISTEN MODE %/fi keys toselect the listening mode.
The listening mode settings are stored separately for each input. Ifthe input mode is set to full auto (“AUTO DETECT” lights), thereceiver selects the optimal listening mode automatically based onthe type of input signal and the speaker settings.
Each turn of the LISTEN MODE knob or press of the LISTEN
MODE %/fi keys switches the setting as listed below.
The listening mode settings are different depending on the type
of input signal.
When the DOLBY DIGITAL signal is input :(The DOLBY DIGITAL or PRO LOGIC, indicator lights up.)
1 DOLBY DIGITAL : DOLBY DIGITAL surround.2 DOLBY D EX : DOLBY DIGITAL EX surround.3 PLII MOVIE : PRO LOGIC II surround MOVIE mode.
(The PRO LOGIC indicator lights up.)4 PLII MUSIC : PRO LOGIC II surround MUSIC mode.
(The PRO LOGIC indicator lights up.)5 PRO LOGIC : PRO LOGIC II surround PRO LOGIC mode.
(The PRO LOGIC indicator lights up.)6 STEREO : Normal stereo playback.
Ambience effects
When you select DOLBY DIGITAL
“DOLBY DIGITAL” will be displayed.
DOLBY DIGITAL
PRO LOGIC L
SL SB SR
C RSWLFE
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.ACTIVE EQ.DSP MODE
DTS.MATRIX
DISCRETE
STEREO
LOUDNESS
NEO:6
CSII A B CLIPAUTO DETECT THX
AUTO
RDSRTY
MEMOSTEREOTUNED
Surround EX
When the DTS or DTS-ES (matrix or discrete) signal is input :
1 DTS 5.1ch : (DTS indicator lights up.)2 DTS MATRIX : (DTS MATRIX indicator lights up.)3 DTS DISCRETE : (DISCRETE indicator lights up.)4 STEREO
When the analog signal or the digital signal (except forDOLBY DIGITAL or DTS signal) is input :
1 PLII MOVIE : PRO LOGIC II surround MOVIE mode.(The PRO LOGIC indicator lights up.)
2 PLII MUSIC : PRO LOGIC II surround MUSIC mode.(The PRO LOGIC indicator lights up.)
3 PRO LOGIC : PRO LOGIC II surround PRO LOGIC mode.(The PRO LOGIC indicator lights up.)
4 NEO:CINEMA : NEO:6 surround.(The NEO:6 indicator lights up.)
5 NEO:MUSIC : NEO:6 surround.(The NEO:6 indicator lights up.)
6 CSII CINEMA : CS 6.1 surround.(The CS II indicator lights up.)
7 CSII MUSIC : CS 6.1 surround.(The CS II indicator lights up.)
8 CSII MONO : CS 6.1 surround.(The CS II indicator lights up.)
9 STEREO : Normal stereo playback. Sound is producedfrom the two front channels only.(The STEREO indicator lights up.)
• Dolby Digital or DTS signal having more channels than the maxi-mum number of playback channels available using the receiver’scurrent settings is input, downmixing is performed to match thenumber of available channels.
•VR6060/29-34/EN 3/11/02, 8:53 PM30
31 EN
Ambience effects
DVD 6-channel playbackUsing a DVD player or the like equipped with six (5.1) output channels andthe receiver, you can enjoy surround sound playback.When you try to play a disc other than Dolby Digital such as DTS CD, nosound is produced or, noise may be heard. To avoid this situation, makesure that you connect the component to the receiver’s DVD/6CH INPUTjacks through a surround processor which can decode the surroundsignal you want to listen to.Connecting a DVD player which can decode the surround signal itself isalso acceptable.
INPUT MODE
DVD/6CH
INPUT MODE
VOLUME
DVD/6CH
VOLUME /
Preparations• Connect your DVD player to the DVD/6CH jacks of the receiver.• Turn on all other components that will be used.• Complete “Preparing for surround sound”. )
1 Press “DVD/6CH” as the input source.
• If speaker system B is on when “DVD/6CH” is selected as the inputsource, it switches off and speaker system A turns on automati-cally.
2 Select "6CH INPUT" by pressing the INPUT MODE key.
3 Start playback of the DVD software.
4Adjust the volume.
• It is not possible to adjust the volume level or sound quality (SET
UP, SOUND) of the channels separately when the receiver is in theDVD/6CH mode. Adjust the volume with the controls of the DVDplayer.For the powered subwoofer, you can adjust the volume of thesubwoofer using the subwoofer’s own volume control.
3 DSP mode (Digital Signal Processor).
DSP can produce these effects without spoiling the sound quality ofthe original music or video source.
1 Pressing the DSP key or DSP MODE key will display the
current DSP MODE status.
2 Each press of the key will switch to the next status as shown
bellow:
1 ARENA : DSP surround ARENA mode.2 JAZZ CLUB : DSP surround JAZZ CLUB mode.3 THEATER : DSP surround THEATER mode.4 STADIUM : DSP surround STADIUM mode.5 DISCO : DSP surround DISCO mode.
• The DSP mode selection is displayed for approximately 3 seconds.• For fine adjustment of the DSP effects, please refer to “Adjusting
the sound”. ¤
4 Adjust the volume.
Notes• Depending on the type of the signal or speaker setting, some listening
modes cannot be selected.• When playback is started, the sound may be cut or interrupted before
the input source is confirmed as Dolby Digital.• To enjoy Dolby Digital surround (as well as all the other listening modes)
from a single component, be sure to use a Dolby Digital compatiblesource component.
•VR6060/29-34/EN 3/11/02, 8:53 PM31
32 EN
Ambience effects
Convenient functions
MULTI CONTROLDIMMERSTEREO
SOUND LISTEN MODE
SOUND
LISTEN MODE%/fi
STEREO
Joystick(MULTI CONTROL5 /∞,DOWN2 / UP3)
DIMMER
Adjusting the soundYou can make further adjustments to the sound while listening toplayback in the surround mode.
1 Press the SOUND key and then use to the MMMMM/????? keys or joystick
(2/3) until the desired item appears in the display.
Each time you press the MMMMM/????? keys or Joystick (2/3), the menu
changes as follows:
Note that some items are not displayed in certain modes.
1 CNTR (Center speaker level adjustment)*2 SR (Right surround speaker level adjustment)*3 SB (Surround back speaker level adjustment)*4 SL (Left surround speaker level adjustment)*5 SUBW (Subwoofer level adjustment)*6 INPUT (Input level adjustment - analog mode only) £7 MIDNIGHT (Midnight mode ON/OFF - Dolby Digital mode only)8 PANORAMA (Panorama mode ON/OFF)**9 DIMENSION (Dimension adjustment)**0 CENTER WIDTH (Center width adjustment)**- CENTER FOCUS (Center focus adjustment)***= CSII DLY (Rear speaker delay adjustment)***~ CSII GAIN (Input gain adjustment)***! TruBass (Trubass adjustment)***
* The adjustment is only temporary for the current input selection.The value will return automatically to the original setup value whenthe power is turned on/off or when the input selection is changed.
** Pro Logic II Music mode only.*** CS II mode only.
2 Use the MULTI CONTROL knob or Joystick (5/∞) to adjust the
setting as desired.
• The adjustment item is displayed for approximately 8 seconds.
Midnight mode (Dolby Digital mode only)When watching movies at night , you might not be able to raise thevolume as loud as normal. Midnight mode compresses the dynamicrange of previously specified parts of the Dolby Digital sound track (likescenes with sudden increases in volume) to minimize the difference involume between the specified and non-specified parts. This makes iteasy to hear all of the sound track, even when listening at low volumes.
1 Press the SOUND key, then press the MMMMM/????? keys or Joystick (2/3)
until “MIDNIGHT” appears on the display.
• This can be selected only if CD/DVD, DVD/6CH, VIDEO 2 or VIDEO 3 isselected as the source and the listen mode is set to “DOLBY DIGITAL.”
2 Use the MULTI CONTROL knob or Joystick (5/∞) to select the
ON or OFF setting.
PRO LOGIC L
SL S SB SR
C RSWLFE
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.ACTIVE EQ.DSP MODE
DTS.MATRIX
DISCRETE
STEREO
LOUDNESS
NEO:6
CSII A B CLIPAUTO DETECT THX
AUTO
RDSRTY
MEMOSTEREOTUNED
Surround EXDOLBY DIGITAL
• The adjustment item is displayed for approximately 8 seconds.• Some Dolby Digital software may not be compatible with the
Midnight mode.
Panorama mode (Pro Logic II Music mode only)When listening to music, you will be able to enjoy the “wraparound”sound effect when you adjust the panorama mode.
1 Press the SOUND key, then press the MMMMM/????? keys or Joystick (2/3)
until “PANORAMA” appears on the display.
2 Use the MULTI CONTROL knob or Joystick (5/∞) to select
PANORAMA ON or OFF.
1 PANORAMA ON : PANORAMA mode is ON.2 PANORAMA OFF : PANORAMA mode is OFF.
L
SL S SB SR
C RSWLFE
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.ACTIVE EQ.DSP MODE
DTS.MATRIX
DISCRETE
STEREO
LOUDNESS
NEO:6
CSII A B CLIPAUTO DETECT THX
AUTO
RDSRTY
MEMOSTEREOTUNED
Surround EXPRO LOGIC
DOLBY DIGITAL
Dimension mode (Pro Logic II Music mode only)When listening to music with certain recordings, you will also be able toachieve a suitable balance from all the speakers by adjusting thedimension mode.
1 Press the SOUND key, then press the MMMMM/????? keys or Joystick (2/3)
until “DIMENSION” appears on the display.
2 Use the MULTI CONTROL knob or Joystick (5/∞) to adjust
the soundfield towards the rear or the front.
Soundfield is adjusted towards the front.
L
SL S SB SR
C RSWLFE
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.ACTIVE EQ.DSP MODE
DTS.MATRIX
DISCRETE
STEREO
LOUDNESS
NEO:6
CSII A B CLIPAUTO DETECT THX
AUTO
RDSRTY
MEMOSTEREOTUNED
Surround EXPRO LOGIC
DOLBY DIGITAL
↓Soundfield is in neutral position.
L
SL S SB SR
C RSWLFE
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.ACTIVE EQ.DSP MODE
DTS.MATRIX
DISCRETE
STEREO
LOUDNESS
NEO:6
CSII A B CLIPAUTO DETECT THX
AUTO
RDSRTY
MEMOSTEREOTUNED
Surround EXPRO LOGIC
DOLBY DIGITAL
↓Soundfield is adjusted towards the rear.
L
SL S SB SR
C RSWLFE
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.ACTIVE EQ.DSP MODE
DTS.MATRIX
DISCRETE
STEREO
LOUDNESS
NEO:6
CSII A B CLIPAUTO DETECT THX
AUTO
RDSRTY
MEMOSTEREOTUNED
Surround EXPRO LOGIC
DOLBY DIGITAL
Center Width mode (Pro Logic II Music mode only)Center width adjustment allows you to enjoy an enchanced sound whenlistening to music through center image from only center speaker, or leftand right speakers or various combinations adjustments.
1 Press the SOUND key, then press the MMMMM/????? keys or Joystick (2/3)until “CENTER WIDTH” appears on the display.
• The CENTER WIDTH indication scrolls across the display.• When the center speaker is switched OFF, this mode will not be
effective.
2 Use the MULTI CONTROL knob or Joystick (5/∞) to adjust theleft-center-right output.
•VR6060/29-34/EN 3/11/02, 8:53 PM32
33 EN
Ambience effects
TruBass adjustment mode (CS II mode only)TruBass adjustment provides deep, rich bass sound to small speakerswithout the need of a subwoofer.
1 Press the SOUND key, then press the MMMMM/????? keys or Joystick (2/3)
until “TruBass” appears.
2 Use the MULTI CONTROL knob or Joystick (5/∞) to select the
following;
1 TruBass OFF
2 TruBass SW
3 TruBass LR
4 TruBass SW + LR
• After selecting 2, 3 or 4, TruBass speaker size and level adjustmentselection will be available.
3 For TruBass speaker selection, use the MULTI CONTROL knob
or Joystick (5/∞) to select any of the following display;
1 TruBass LARGE
2 TruBass MID
3 TruBass SMALL
4 Use the MULTI CONTROL knob or Joystick (5/∞) to adjust the
TruBass Level.
• The adjustment range is from 0 (TruBass OFF) to 10.
L
SL SB SR
C R
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.ACTIVE EQ.DSP MODE
DTS.MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII A B CLIPAUTO DETECT THX
AUTO
RDSRTY
MEMOSTEREOTUNED
Surround EXSW
LFE
Subwoofer adjustmentIt is easy to adjust the volume of the subwoofer using the remote control.
1 Press the SOUND key, then press the MMMMM/????? keys or Joystick (2/3)
until “SUBW” appears on the display.
2 Use the MULTI CONTROL knob or Joystick (5/∞) to adjust the
volume.
• The adjustment range is from –10 dB to +10 dB.
L
S SB
C RSWLFE
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.ACTIVE EQ.DSP MODE
DTS.MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII A B CLIPAUTO DETECT THX
AUTO
RDSRTY
MEMOSTEREOTUNED
Surround EX
SL SR
Display dimmer adjustmentThe dimmer function lets you select the brightness of the receiver'sdisplay. You might find this useful if you darken your room to watchmovies or listen to music.
Each time you press the DIMMER key, the display’s brightness
changes among the three available settings.
Select the brightness level you find most pleasing.
1 Bright
2 Medium
3 Dark
96kHz LPCM playbackThe receiver is compatible with the 96kHz LPCM playback. To play a96kHz DVD, set the listen mode to “STEREO”.
• In FULL AUTO input mode the listen mode will automatically be STEREO.• When in DIGITAL MANUAL input mode (listen mode is not STEREO),
“FS 96kHz” will appear in the display and no sound can be heard fromthe speakers.Press the LISTEN MODE or STEREO key (the listen mode changes tothe STEREO mode) to output sound from the speakers.
Center image will be heard from center speaker only.
L
SL S SB SR
C RSWLFE
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.ACTIVE EQ.DSP MODE
DTS.MATRIX
DISCRETE
STEREO
LOUDNESS
NEO:6
CSII A B CLIPAUTO DETECT THX
AUTO
RDSRTY
MEMOSTEREOTUNED
Surround EXPRO LOGIC
DOLBY DIGITAL
Center image will be heard from left and right speakers only.
L
SL S SB SR
C RSWLFE
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.ACTIVE EQ.DSP MODE
DTS.MATRIX
DISCRETE
STEREO
LOUDNESS
NEO:6
CSII A B CLIPAUTO DETECT THX
AUTO
RDSRTY
MEMOSTEREOTUNED
Surround EXPRO LOGIC
DOLBY DIGITAL
• When in other position, center image from center speaker, left andright speakers can be heard simultaneously with various combinations.
Circle Surround II modeWhen you select the circle surround II mode, you will be able to enjoy themulti surround sound from the stereo source.
Use the LISTEN MODE knob or LISTEN MODE fi/% keys for CS II selection.
Center Focus mode (CS II mode only)Center focus elevate level adjustment allows you to enjoy an enchancedsound when you select CS II CINEMA/MUSIC/MONO. It repositions thesound image to an optimal position more natural to the listener throughthe center image.
1 Press the SOUND key, then press the MMMMM/????? keys or Joystick (2/3)until “CENTER FOCUS” appears on the display.
L
SL SB SR
C R
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.ACTIVE EQ.DSP MODE
DTS.MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII A B CLIPAUTO DETECT THX
AUTO
RDSRTY
MEMOSTEREOTUNED
Surround EXSW
LFE
2 Use the MULTI CONTROL knob or Joystick (5/∞) to adjust thecenter elevation level.• The adjustment range is from 0 to 10.
L
SL SB SR
C R
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.ACTIVE EQ.DSP MODE
DTS.MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII A B CLIPAUTO DETECT THX
AUTO
RDSRTY
MEMOSTEREOTUNED
Surround EXSW
LFE
• CENTER FOCUS will not be available when the center speaker is OFF.
CS II Rear Delay adjustment mode (CS II mode only)CS II Rear Delay adjustment provides a better sound effect from the rearspeakers.
1 Press the SOUND key, then press the MMMMM/????? keys or Joystick (2/3)until “CSII DLY” appears on the display.
2 Use the MULTI CONTROL knob or Joystick (5/∞) to adjust therear speaker.• The adjustment range is from 0 ms to 25 ms.
L
SL SB SR
C R
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.ACTIVE EQ.DSP MODE
DTS.MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII A B CLIPAUTO DETECT THX
AUTO
RDSRTY
MEMOSTEREOTUNED
Surround EXSW
LFE
CS II Gain adjustment mode (CS II mode only)CS II GAIN allows user to adjust the input gain for the Circle Surround IIprocessing.
1 Press the SOUND key, then press the MMMMM/????? keys or Joystick (2/3)until “CSII GAIN” appears on the display.
2 Use the MULTI CONTROL knob or Joystick (5/∞) to adjust theinput gain.• The adjustment range is from 0 to 18.
L
SL SB SR
C R
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.ACTIVE EQ.DSP MODE
DTS.MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII A B CLIPAUTO DETECT THX
AUTO
RDSRTY
MEMOSTEREOTUNED
Surround EXSW
LFE
•VR6060/29-34/EN 3/11/02, 8:54 PM33
34 EN
The remote control supplied with this receiver is also capable
of controlling components from a variety of manufacturers
once you register the appropriate setup codes into the
remote control unit.
Low battery warningReplace all two batteries with new ones when you notice a shorteningof the distance from which the remote control will operate.
For LCD remote control (RC-R0816)
The remote control is designed to retain setup codes in memory whileyou change batteries.
For non-LCD remote control (RC-R0725)
After changing batteries, please re-enter the setup codes.
Registering setup codes for other components
SOURCE
Numeric keys
REMOTE MODE
INPUTSELECTOR
1 Find the setup code of the component to be registered.
• Refer to the setup code lists to find the setup code for thecomponent to be registered. flExample: To register a DVD made by KENWOOD, you would enter“805”.
Input Component Maker Code Key
(DVD) DVD player KENWOOD 805, 808 DVD
2Registering components for REMOTE MODE (DVD, CBL,DSS/SAT, VCR, TV, OTHERS) keys.
1 For DVD, CBL, DSS/SAT, VCR or TV keys;
Hold down the SOURCE key and press the numeric keys to
enter the setup code.
• Example: Press “805” to register a DVD player manufactured byKENWOOD.
• If you push an invalid key, the remote control will display“ERROR” and exit the setup mode.
2 The OTHERS key enables you to operate another DVD, CBL,
DSS/SAT, VCR or TV component.
For OTHERS key;
Hold down the OTHERS key and press the numeric keys to
enter the setup code.
• Example: After you have registered the KENWOOD DVD player,press “804” to register another DVD player which is manufacturedby Panasonic.
• If you push an invalid key, the remote control will display“ERROR” and exit the setup mode.
3Press any of the REMOTE MODE key and then press theSOURCE key to check that the component you want tocontrol turns on.
If the component does not react, and there is more than one
setup code, enter another setup code and try again.
• If the component is already on, pressing the SOURCE key willturn it off.
4Repeat steps 2 to 3 to register additional components untilall components have been registered.
Alternative REMOTE MODE key .This operation is optional and is convenient when you link an INPUTSELECTOR key to the REMOTE MODE key. While operating onecomponent, the INPUT SELECTOR key functions as an alternativeREMOTE MODE key to select another component.
• Example: REMOTE MODE (DVD) key can be linked to the INPUTSELECTOR (VIDEO 1) key as described below;
1 After registering the setup code, press and hold the SOURCE
key and then press the REMOTE MODE (DVD) key.
2 While holding down SOURCE press the INPUT SELECTOR
(VIDEO 1) key.
• Now the VIDEO 1 key will function as a DVD key which can beselected at the same time while operating a CD player.
• Repeat step 1 to 2 to link other INPUT SELECTOR keys.
NoteAlthough each setup code is designed to work with a number ofdifferent models, certain codes may not work with some models.(Also, certain codes may only operate some of the functions availableon a given model.)
Basic remote control operations for other components
LCD panelfor VR-6060 only.
•VR6060/29-34/EN 3/11/02, 8:54 PM34
35 EN
Basic remote control operations for other components
Operating other componentsThis operation lets you operate the registered components.KENWOOD audio components with system control turn on and offautomatically with the receiver via the system control connections.
SOURCERECEIVER
INPUTSELECTOR
1Use the INPUT SELECTOR keys to select the component youdesire.• Pressing the INPUT SELECTOR keys also changes the input selector
on the receiver.
• When you operate your registered DVD player, Cable tuner,DSS/SAT receiver, VCR or TV, go to step 2.
• When you operate the CD player, Cassette deck, MD player, orTuner with system control connection, go to step 3.
2Press the SOURCE key.
• To return to the receiver operation mode, press the RECEIVER key.
3Press the operation keys you desire. °
The remote control mode remains at the selected input. If youwish to operate another component, repeat step 2 or 3.
NoteBe sure to point the remote control at the remote sensor on thereceiver when you want to operate KENWOOD components connectedby system control cords. Otherwise, point the remote control at thecomponent you want to operate.
Storing the remote control code of the othercomponents (For VR-6060 only)
The remote control unit can store the remote control code of the othercomponents and you can operate the other components from the remotecontrol unit. The remote control code is stored on the key or memory ofthe remote control unit.
Storing on the keyYou can store the remote control code to the key as shown below:
P.CALL 4 /DOWN
P.CALL/UP ¢
TUNING
+
TOP MENUSET UP
MENUSOUND
TV CONTROL
VOL.
VOLUME
+
- - INPUT SEL
+
-CH
DVD
VCR
CBL
TV
DSS/SAT
OTHERS
RECEIVER
SOURCE POWER
ACTIVE EQ
OSD RETURN
DISC SEL DISC SKIP
FLIP BAND
INPUT SEL A/B AUTO 8
DVD/6CH CD/DVD PHONO TUNER
VIDEO 1 VIDEO 2 MD/TAPE
MUTE
DVD
ENTER
INPUT SELECTOR
MULTICONTROL
¢
4
1 ¡ 2 6
7 DIMMER
™ £
™
1
4
7
+10
2
5
8
0
3
6
9
+100
REMOTE MODE
LISTEN MODE
DSP MODESTEREOINPUT MODE
SPEAKER EQ
™
VIDEO 3
PAGE
LEARN
DISC SKIPDISC SEL
SOURCE
1 Rewind¡ Fast forward
Numeric keys
LEARN
CH + / — Skip ¢/4
OSDPAGE fi/%
RETURN
TOP MENU
3/8 (Play/Pause)2 Flip8 Pause7 Stop
Cursor 5/∞/2/3ENTER
MENU
1 Point the infrared ray system part of another remote control unit
to the remote sensor of the remote control unit.
2 Press the LEARN key.
• This remote control is ready to receive the remote control code fromthe other source.
LEARN
3 Press any of the REMOTE MODE (DVD, CBL, DSS/SAT, VCR, TV,
OTHERS) keys to select the input of the desired remote control
unit.
4 Press the desired key of the remote control unit.
LEARN
5 From the remote control unit of the other source, press the key
that you want to store.
• The remote control code is sent to the remote control unit.• “OK” appears when finished.
LEARN
• When the appropriate code is not properly stored, “AGAIN” will bedisplayed. Repeat from step 2 onwards.
LEARN
• If the code cannot be stored after a few attempts, “ERROR" willappear. Repeat from step 2 onwards.
• If LEARN mode‘s storage is full, “FULL" appears on the display.
6 The remote control code is stored on the key of this remote
control unit.
7 Press the LEARN key again to exit the learning mode.
LCD panelfor VR-6060 only.
Remote controlunit of the othersource.
Infrared ray system part
•VR6060/35-44/EN 3/11/02, 8:54 PM35
36 EN
Setup code chart (RC-R0816) (VR-6060) and (RC-R0725) (KRF-V8060D)
Basic remote control operations for other components
TV Setup codes
Maker Setup codes
AKAI 125BELL+HOWELL 142CENTURION 126CORONAD 127DAEWOO 136, 140, 141, 145EMERSON 130, 131, 132, 133, 146FISHER 119G.E. 102, 122, 129GOLD STAR 137, 148HITACHI 114, 115JVC 113KTV 138, 139LOEWE 123, 124MAGNAVOX 109, 147MARANTZ 121MITSUBISHI 121PANASONIC 111, 112, 122, 129PHILIPS 109, 147PIONEER 116PROSCAN 117RADIOSHACK 128RCA 102, 103, 104, 105, 106, 126SAMSUNG 134, 135SANYO 119SEARS 120SHARP 110SONY 101SYMPHONIC 143, 144TOSHIBA 120QUASAR 111, 118ZENITH 107, 108
Maker Setup codes
HITACHI 812JVC 801KENWOOD 805, 808MITSUBISHI 810ONKYO 815, 816PANASONIC 804PHILIPS 807PIONEER 803PROSCAN 811RCA 811SAMSUNG 814SONY 802TOSHIBA 806YAMAHA 809ZENITH 806, 813
DVD player Setup codes
Maker Setup codes
GEMINI 218G.I. 209HAMLIN 210, 211, 234, 235JERROLD 201, 202, 224, 225, 226, 227,
228, 229, 233MACOM 215, 216, 217MAGNAVOX 236OAK 212, 213, 214PANASONIC 221, 222, 232PHILIPS 219, 220, 237, 238, 239, 240PIONEER 206, 207SAMSUNG 223S. ATLANTA 203, 230, 231TOCOM 208ZENITH 204, 205
CBL codes
DSS/SAT codes
Maker Setup codes
ECHOSTAR 903G.I. 902HITACHI 908HUGHES 906PANASONIC 905PRIMESTAR 909RCA 901SONY 907TOSHIBA 904
Maker Setup codes
AIWA 352AKAI 354, 355, 356BELL+HOWELL 351DAEWOO 349EMERSON 334, 335, 336, 337, 338FISHER 330, 341, 342, 343G.E. 307, 321GOLD STAR 323GO_VIDEO 347, 348, 353HITACHI 307, 308, 328, 329JVC 324, 325, 326, 327MAGNAVOX 311, 312, 313MITSUBISHI 315, 316, 317, 318, 357, 358NEC 344, 345ORION 335PANASONIC 309, 310PHILIPS 313QUASAR 309, 310, 311, 312RCA 308SAMSUNG 332, 339, 340SANYO 351SCOTT 331SHARP 319, 320SHINTOM 333SONY 301, 302, 303, 304, 305, 306SYNPHO 346TEKNICA 346, 350TOSHIBA 314ZENITH 322
VCR Setup codes
•VR6060/35-44/EN 3/11/02, 8:55 PM36
37 EN
CASSETTE deck, CD player & MD recorder operationsYou can perform these basic operations using the keys described below when connected to KENWOOD cassette deck, CD player or MD recorderequipped with system control operations. &The LCD panel is only for remote control RC-R0816 (VR-6060 model).
Cassette deck operations keys CD player operation keys
P.CALL 4 /DOWN
P.CALL/UP ¢
TUNING
+
TOP MENUSET UP
MENUSOUND
TV CONTROL
VOL.
VOLUME
+
- - INPUT SEL
+
-CH
DVD
VCR
CBL
TV
DSS/SAT
OTHERS
RECEIVER
SOURCE POWER
ACTIVE EQ
OSD RETURN
DISC SEL DISC SKIP
FLIP BAND
INPUT SEL A/B AUTO 8
DVD/6CH CD/DVD PHONO TUNER
VIDEO 1 VIDEO 2 MD/TAPE
LOUDNESS TONE BASS BOOST
MUTE
DVD
ENTER
INPUT SELECTOR
MULTICONTROL
¢
4
1 ¡ 2 6
7 DIMMER
™ £
™
1
4
7
+10
2
5
8
0
3
6
9
+100
REMOTE MODE
LISTEN MODE
DSP MODESTEREOINPUT MODE
SPEAKER EQ
™
VIDEO 3
AV AUX
PAGE
LEARN
A/B(Cassette deck
selection)
3/8 (3 Play)2 (Reverse play)
1 (Rewind)¡ (Fast Forward)
7 (Stop)
P.CALL 4 /DOWN
P.CALL/UP ¢
TUNING
+
TOP MENUSET UP
MENUSOUND
TV CONTROL
VOL.
VOLUME
+
- - INPUT SEL
+
-CH
DVD
VCR
CBL
TV
DSS/SAT
OTHERS
RECEIVER
SOURCE POWER
ACTIVE EQ
OSD RETURN
DISC SEL DISC SKIP
FLIP BAND
INPUT SEL A/B AUTO 8
DVD/6CH CD/DVD PHONO TUNER
VIDEO 1 VIDEO 2 MD/TAPE
LOUDNESS TONE BASS BOOST
MUTE
DVD
ENTER
INPUT SELECTOR
MULTICONTROL
¢
4
1 ¡ 2 6
7 DIMMER
™ £
™
1
4
7
+10
2
5
8
0
3
6
9
+100
REMOTE MODE
LISTEN MODE
DSP MODESTEREOINPUT MODE
SPEAKER EQ
™
VIDEO 3
AV AUX
PAGE
LEARN
3/8 (Play/Pause) 1 (Backward Search)¡ (Forward Search)
3 (Skip up)2 (Skip down)
7 (Stop)
Numeric keys(Select tracks)
DISC SKIP
DISC SEL(Disc selection)
RC-R0816/R0725 RC-R0816/R0725
MD recorder operation keys
P.CALL 4 /DOWN
P.CALL/UP ¢
TUNING
+
TOP MENUSET UP
MENUSOUND
TV CONTROL
VOL.
VOLUME
+
- - INPUT SEL
+
-CH
DVD
VCR
CBL
TV
DSS/SAT
OTHERS
RECEIVER
SOURCE POWER
ACTIVE EQ
OSD RETURN
DISC SEL DISC SKIP
FLIP BAND
INPUT SEL A/B AUTO 8
DVD/6CH CD/DVD PHONO TUNER
VIDEO 1 VIDEO 2 MD/TAPE
LOUDNESS TONE BASS BOOST
MUTE
DVD
ENTER
INPUT SELECTOR
MULTICONTROL
¢
4
1 ¡ 2 6
7 DIMMER
™ £
™
1
4
7
+10
2
5
8
0
3
6
9
+100
REMOTE MODE
LISTEN MODE
DSP MODESTEREOINPUT MODE
SPEAKER EQ
™
VIDEO 3
AV AUX
PAGE
LEARN
3/8 (Play)
7 (Stop)
+100(Select tracks)
1 (Backward Search)¡ (Forward Search)
Numeric keys(Select tracks)
3 (Skip up)2 (Skip down)
RC-R0816/R0725
Basic remote control operations for other components
•VR6060/35-44/EN 3/11/02, 8:55 PM37
38 EN
Basic remote control operations for other components
Other components’ operationsRefer to the following for the type of remote control operations available for each component.
• When pressing keys in succession, press each key firmly and be sureto wait at least 1 second before pressing the next key.
• Numeric keys function the same as the numeric keys on the originalremote.
These keys can be used to perform the basic operations of KENWOOD and other manufacturers’ components which the setup code for each
component had been entered beforehand. flThe LCD panel is only for remote control RC-R0816 (VR-6060 model).
TV operation keys VCR operation keys
P.CALL 4 /DOWN
P.CALL/UP ¢
TUNING
+
TOP MENUSET UP
MENUSOUND
TV CONTROL
VOL.
VOLUME
+
- - INPUT SEL
+
-CH
DVD
VCR
CBL
TV
DSS/SAT
OTHERS
RECEIVER
SOURCE POWER
ACTIVE EQ
OSD RETURN
DISC SEL DISC SKIP
FLIP BAND
INPUT SEL A/B AUTO 8
DVD/6CH CD/DVD PHONO TUNER
VIDEO 1 VIDEO 2 MD/TAPE
LOUDNESS TONE BASS BOOST
MUTE
DVD
ENTER
INPUT SELECTOR
MULTICONTROL
¢
4
1 ¡ 2 6
7 DIMMER
™ £
™
1
4
7
+10
2
5
8
0
3
6
9
+100
REMOTE MODE
LISTEN MODE
DSP MODESTEREOINPUT MODE
SPEAKER EQ
™
VIDEO 3
AV AUX
PAGE
LEARN
(Power on/off)
Numeric keys
VOL + / – (Volume + / –)
CH + / – (Channel + / –)
MUTE
INPUT SEL(Input selection)
ENTER
P.CALL 4 /DOWN
P.CALL/UP ¢
TUNING
+
TOP MENUSET UP
MENUSOUND
TV CONTROL
VOL.
VOLUME
+
- - INPUT SEL
+
-CH
DVD
VCR
CBL
TV
DSS/SAT
OTHERS
RECEIVER
SOURCE POWER
ACTIVE EQ
OSD RETURN
DISC SEL DISC SKIP
FLIP BAND
INPUT SEL A/B AUTO 8
DVD/6CH CD/DVD PHONO TUNER
VIDEO 1 VIDEO 2 MD/TAPE
LOUDNESS TONE BASS BOOST
MUTE
DVD
ENTER
INPUT SELECTOR
MULTICONTROL
¢
4
1 ¡ 2 6
7 DIMMER
™ £
™
1
4
7
+10
2
5
8
0
3
6
9
+100
REMOTE MODE
LISTEN MODE
DSP MODESTEREOINPUT MODE
SPEAKER EQ
™
VIDEO 3
AV AUX
PAGE
LEARN
INPUT SEL(Input selection)
Numeric keys
CH + / – (Channel + / –)
3/8 (3 Play)
8 (Pause)
1 (Rewind)¡ (Fast Forward)
7 (Stop)
SOURCE(Source power)
RC-R0816/R0725 RC-R0816/R0725
1 Select the input source.
2 Press the keys corresponding to the operations you desire.
Refer to the following sections for details.
•VR6060/35-44/EN 3/11/02, 8:55 PM38
39 EN
Basic remote control operations for other components
DSS/SAT receiver operation keys Cable tuner operation keys
P.CALL 4 /DOWN
P.CALL/UP ¢
TUNING
+
TOP MENUSET UP
MENUSOUND
TV CONTROL
VOL.
VOLUME
+
- - INPUT SEL
+
-CH
DVD
VCR
CBL
TV
DSS/SAT
OTHERS
RECEIVER
SOURCE POWER
ACTIVE EQ
OSD RETURN
DISC SEL DISC SKIP
FLIP BAND
INPUT SEL A/B AUTO 8
DVD/6CH CD/DVD PHONO TUNER
VIDEO 1 VIDEO 2 MD/TAPE
LOUDNESS TONE BASS BOOST
MUTE
DVD
ENTER
INPUT SELECTOR
MULTICONTROL
¢
4
1 ¡ 2 6
7 DIMMER
™ £
™
1
4
7
+10
2
5
8
0
3
6
9
+100
REMOTE MODE
LISTEN MODE
DSP MODESTEREOINPUT MODE
SPEAKER EQ
™
VIDEO 3
AV AUX
PAGE
LEARN
CH + / – (Channel + / –)
ENTER
MENU5 (Cursor up)∞ (Cursor down)2 (Cursor left)3 (Cursor right)
Numeric keys
SOURCE(Source power)
P.CALL 4 /DOWN
P.CALL/UP ¢
TUNING
+
TOP MENUSET UP
MENUSOUND
TV CONTROL
VOL.
VOLUME
+
- - INPUT SEL
+
-CH
DVD
VCR
CBL
TV
DSS/SAT
OTHERS
RECEIVER
SOURCE POWER
ACTIVE EQ
OSD RETURN
DISC SEL DISC SKIP
FLIP BAND
INPUT SEL A/B AUTO 8
DVD/6CH CD/DVD PHONO TUNER
VIDEO 1 VIDEO 2 MD/TAPE
LOUDNESS TONE BASS BOOST
MUTE
DVD
ENTER
INPUT SELECTOR
MULTICONTROL
¢
4
1 ¡ 2 6
7 DIMMER
™ £
™
1
4
7
+10
2
5
8
0
3
6
9
+100
REMOTE MODE
LISTEN MODE
DSP MODESTEREOINPUT MODE
SPEAKER EQ
™
VIDEO 3
AV AUX
PAGE
LEARN
CH + / – (Channel + / –)
ENTER
Numeric keys
SOURCE(Source power)
RC-R0816/R0725 RC-R0816/R0725
DVD player operation keys
P.CALL 4 /DOWN
P.CALL/UP ¢
TUNING
+
TOP MENUSET UP
MENUSOUND
TV CONTROL
VOL.
VOLUME
+
- - INPUT SEL
+
-CH
DVD
VCR
CBL
TV
DSS/SAT
OTHERS
RECEIVER
SOURCE POWER
ACTIVE EQ
OSD RETURN
DISC SEL DISC SKIP
FLIP BAND
INPUT SEL A/B AUTO 8
DVD/6CH CD/DVD PHONO TUNER
VIDEO 1 VIDEO 2 MD/TAPE
LOUDNESS TONE BASS BOOST
MUTE
DVD
ENTER
INPUT SELECTOR
MULTICONTROL
¢
4
1 ¡ 2 6
7 DIMMER
™ £
™
1
4
7
+10
2
5
8
0
3
6
9
+100
REMOTE MODE
LISTEN MODE
DSP MODESTEREOINPUT MODE
SPEAKER EQ
™
VIDEO 3
AV AUX
PAGE
LEARN
TOP MENU(Title)
PAGE %/fi(Page up or down)
MENU
RETURNOSD
2 (Flip)3/8 (3 Play)
8 (Pause)
7 (Stop)
1 (Backward Search)¡ (Forward Search)
¢ (Skip up)4 (Skip down)
Numeric keys(Select tracks)
ENTER
5 (Cursor up)∞ (Cursor down)2 (Cursor left)3 (Cursor right)
SOURCE(Source power)
RC-R0816/R0725
•VR6060/35-44/EN 3/11/02, 8:55 PM39
40 EN
In case of difficulty
Tuner
Cause
• No antenna is connected.• The broadcast band is not set properly.• The frequency of the desired station is not
tuned.
• Noise due to ignition noise from an automo-bile.
• Noise due to interference from an electricappliance.
• Noise due to a nearby TV set.
• The preset station belongs to a frequency thatcannot be received.
• The preset memory was cleared because thepower cord had been unplugged for a longperiod of time.
Remedy
• Connect an antenna. ^• Set the broadcast band properly.• Tune the frequency of the desired station.
§
• Install the outdoor antenna away from theroad.
• Turn off the power to the appliance.
• Install the receiver farther away from the TV.
• Preset a station with a receivable frequency.
• Preset the station again.
Symptom
Radio stations cannot be received.
Interference.
A station which was preset cannot be re-
ceived by pressing the corresponding nu-
meric key.
Amplifier
Cause
• The speaker cords are disconnected.
• VOLUME is set to the minimum position.• MUTE is ON.• The SPEAKERS switches are set to OFF.
• Speaker cords are short-circuited.
• The speaker cord is disconnected.
• The surround speaker cords and/or the centerspeaker cord is disconnected.
• A surround mode has not been engaged.• The surround and/or center volume controls
are set to the minimum level.
• The audio cord from the record player is notconnected to the PHONO jacks.
• The record player is not grounded.
• There are many possible causes for this prob-lem, depending on the type of DVD playerused.
• The input mode is set to digital manual.
• The software is copy-guarded.
Remedy
• Connect them properly referring to “Connect-ing the speakers” $
• Adjust the volume to a proper level.• Turn OFF the MUTE. ¢• Set the SPEAKERS switches to ON. ™
• Turn the power off, eliminate the short-circuit-ing, then turn on the power again.
• Connect it properly referring to “Connectingthe speakers”. $
• Connect it properly referring to “Connectingthe speakers”. $
• Select a surround mode.• Adjust the speaker levels using the test tone.
¡
• Insert the audio cord plugs securely into thePHONO jacks.
• Connect the grounding wire to the GND termi-nal on the rear panel.
• Set the input mode to digital manual beforestarting playback of the Dolby Digital source.
8
• Press the INPUT MODE key to select to fullauto mode. 8
• Copy-guarded video software cannot be re-corded.
Symptom
No sound from the speakers.
The standby indicator blinks and sound is
not output.
Sound is not output from one of the speakers.
Sound is not output from the surround
speakers and / or the center speaker, or their
sound is very small.
A humming noise is generated when the
PHONO input selector is selected.
When playing a Dolby Digital source signal
using a DVD player, the sound is cut off soon
after it starts.
No sound is produced during playback from
a DVD player.
A video source cannot be recordednormally.
Resetting the MicrocomputerThe microcomputer may malfunction (unit cannot be operated, or
shows an erroneous display) if the power cord is unplugged while
the power is ON, or due to some other external factor. If this
happens, execute the following procedure to reset the microcom-
puter and return the unit to its normal operating condition.
• Please note that resetting the microcomputer will clear the contentsof the memory and returns the unit to the state it was in when it leftthe factory.
For the U.S.A. and CanadaUnplug the power cord from the wall outlet, then plug it
back in while holding down the POWER ON/STANDBY
key.
For other countriesWith the power cord plugged in, turn the POWER ON/
OFF key OFF. Then, while holding down the ON/
STANDBY key, press POWER ON/OFF.
•VR6060/35-44/EN 3/11/02, 8:55 PM40
41 EN
Remote control unit
Cause
• No setup codes registered for the respectiveinput(s).
• The remote control is set to a different opera-tion mode.
• Batteries are exhausted.• The remote control unit is too far away from
the main system, controlling angle is too large,or there is an obstacle between the receiverand the remote.
• The audio cords and system control cords arenot connected properly.
• No software is loaded in the source component.
• An attempt is made to play a tape which isbeing recorded in the cassette deck.
• The remote control has not been set to theoperation mode for the component you wishto control.
Remedy
• Register a setup code at the respective input(s).fl
• Press the source select keys or SOURCE
keys to select the appropriate operation mode.• Replace with new batteries.• Operate the remote control unit within the
controllable range.
• Connect properly referring to “Setting up thesystem”.
• Place software in the source component youwant to play.
• Wait until recording has completed.
• Press the source select keys or SOURCE
key to activate the operation mode for thecomponent you want to control beforeoperation. fi
Symptom
Certain inputs cannot be selected using the
remote control.
Remote control operation is not possible.
In case of difficulty
•VR6060/35-44/EN 3/11/02, 8:55 PM41
42 EN
Specifications
For the U.S.A and Canada
AUDIO section (VR-6060)Rated power output during STEREO operation
Effective power output during SURROUND operation
FRONT (20 ~ 20 kHz, 0.09 % T.H.D. at 8 Ω one channel driven)............................................................................... 100 W + 100 W
CENTER (20 ~ 20 kHz, 0.09 % T.H.D. at 8 Ω one channeldriven) .................................................................................. 100 WSURROUND (20 ~ 20 kHz, 0.7 % T.H.D. at 8 Ω one channeldriven) ................................................................... 100 W + 100 WSURROUND BACK/SUBWOOFER (20 ~ 20 kHz, 0.09 % T.H.D.at 8 Ω one channel driven) ................................................. 100 W
Total harmonic distortion ....................... 0.009 % (1 kHz, 50 W, 8 Ω)Frequency response
Line (CD/DVD, TAPE, VIDEO 1, VIDEO 2, VIDEO 3, DVD/6CH)................................................. 10 Hz ~ 100 kHz, +0 dB ~ –3.0 dB
PHONO ‘RIAA’ response .............. 40 Hz ~ 20 kHz, +1.5 dB ~ –3.0 dBMaximum input level
PHONO (MM) .................................... 45 mV, 1 % T.H.D. at 1 kHzSignal to noise ratio (IHF’66)
PHONO (MM) ........................................................................ 75 dBLine (CD/DVD, TAPE, VIDEO 1, VIDEO 2, VIDEO 3, DVD/6CH)............................................................................................... 95 dB
Loudness controlVOLUME at –30 dB level ...................................... +6 dB (100 Hz)
Input sensitivity / impedancePHONO (MM) ........................................................ 6.0 mV / 47 kΩLine (CD/DVD, TAPE, VIDEO 1, VIDEO 2, VIDEO 3, DVD/6CH).............................................................................. 500 mV / 47 kΩ
Output level / impedanceTAPE REC ............................................................... 500 mV / 1 kΩPRE OUT (SURROUND BACK CHANNEL) .............. 2.5 V / 1 kΩPRE OUT (SUBWOOFER) ......................................... 2.5 V / 1 kΩ
Tone controlBASS................................................................ ±10 dB (at 100 Hz)TREBLE ............................................................ ±10 dB (at 10 kHz)
For other countries
AUDIO section (KRF-V8060D)Effective power output during STEREO operation
1 kHz, 10 %, 8 Ω ......................................................... 110 W + 110 WRated power output during STEREO operation
Effective power output during SURROUND operationFRONT (1 kHz, 10% T.H.D. at 8 Ω one channel driven)............................................................................... 110 W + 110 W
CENTER (1 kHz, 10% T.H.D. at 8 Ω one channel driven).............................................................................................. 110 W
SURROUND (1 kHz, 10% T.H.D. at 8 Ω one channel driven)............................................................................... 110 W + 110 W
SURROUND BACK/SUBWOOFER (1 kHz, 10% T.H.D. at 8 Ωone channel driven) ............................................................ 110 W
Total harmonic distortion ........................ 0.009% (1 kHz, 50 W, 8 Ω)Frequency response
Line (CD/DVD, TAPE, VIDEO 1, VIDEO 2, VIDEO 3, DVD/6CH)................................................. 10 Hz ~ 100 kHz, +0 dB ~ –3.0 dB
PHONO ‘RIAA’ response ................ 40 Hz ~ 20 kHz, 1.5 dB ~ –3.0 dBMaximum input level
PHONO (MM) ....................................45 mV, 1 % T.H.D. at 1 kHzSignal to noise ratio (IHF’66)
PHONO (MM) ........................................................................ 75 dBLine (CD/DVD, TAPE, VIDEO 1, VIDEO 2, VIDEO 3, DVD/6CH)............................................................................................... 95 dB
Loudness controlVOLUME at –30 dB level ...................................... +6 dB (100 Hz)
Input sensitivity / impedancePHONO (MM) ........................................................ 6.0 mV / 47 kΩLine (CD/DVD, TAPE, VIDEO 1, VIDEO 2, VIDEO 3, DVD/6CH).............................................................................. 500 mV / 47 kΩ
Output level / impedanceTAPE REC ............................................................... 500 mV / 1 kΩPRE OUT (SURROUND BACK CHANNEL) .............. 2.5 V / 1 kΩPRE OUT (SUBWOOFER) ......................................... 2.5 V / 1 kΩ
Tone controlBASS................................................................ ±10 dB (at 100 Hz)TREBLE ............................................................ ±10 dB (at 10 kHz)
Caution : Read this page carefully to ensure safeoperation.
100 watts per channel minimum RMS, both channels driven,at 8 Ω from 20 Hz to 20 kHz with no more than 0.09% totalharmonic distortion. (FTC) 100 watts per channel minimum RMS, both channels driven,
at 8 Ω from 20 Hz to 20 kHz with no more than 0.09% totalharmonic distortion. (FTC)
•VR6060/35-44/EN 3/11/02, 8:55 PM42
43 EN
Notes1. KENWOOD follows a policy of continuous advancements in development. For this reason specifications may be changed without notice.2. The full performance may not be exhibited in an extremely cold location (under a water-freezing temperature).
Specifications
DIGITAL AUDIO sectionSampling frequency ...................... 32 kHz, 44.1 kHz, 48 kHz, 96 kHzInput level / impedance / wave length
Optical ........................... (–15 dBm ~ –24 dBm), 660 nm ±30 nmCoaxial ................................................................... 0.5 Vp-p / 75 Ω
VIDEO sectionVIDEO inputs / outputs
VIDEO (composite) .................................................. 1 Vp-p / 75 ΩS VIDEO inputs /outputs
S VIDEO (luminance signal) ................................... 1 Vp-p / 75 ΩS VIDEO (chrominance signal) ....................... 0.286 Vp-p / 75 Ω
COMPONENT VIDEO inputs /outputsCOMPONENT VIDEO (luminance signal) .............. 1 Vp-p / 75 ΩCOMPONENT VIDEO (CB/CR-signal) ............ ±0.32 Vp-p / 75 Ω
FM tuner sectionTuning frequency range................................. 87.5 MHz ~ 108.0 MHzUsable sensitivity (MONO)
VR-6060................... 1.3 µV (75 Ω)/ 13.2 dBf (75 kHz dev, SINAD 30 dB)
KRF-V8060D ....................................................................................................... 1.6 µV (75 Ω)/ 15.2 dBf (75 kHz dev, SINAD 30 dB)
50 dB quieting sensitivitySTEREO ..................................................... 28 µV (75 Ω)/ 40.2 dBf
Total harmonic distortionMONO (1 kHz, 75 kHz dev) .......................... 0.5% (65 dBf input)STEREO (1 kHz, 67.5 + 6.75 kHz dev) ......... 0.7% (65 dBf input)
Signal to noise ratioMONO (1 kHz, 75 kHz dev) ........................ 75 dB (65 dBf input)STEREO (1 kHz, 67.5 + 6.75 kHz dev) ....... 68 dB (65 dBf input)
Stereo separation (1 kHz) ........................................................... 40 dBSelectivity (±400 kHz) (VR-6060) ............................................... 70 dB (KRF-V8060D) ......................................... 50 dBFrequency response (30 Hz ~ 15 kHz) .................... +0.5 dB, –3.0 dB
AM tuner sectionTuning frequency range
10 kHz step ................................ 530 kHz ~ 1,700 kHz (VR-6060)10 kHz step ......................... 530 kHz ~ 1,610 kHz (KRF-V8060D) 9 kHz step ......................... 531 kHz ~ 1,602 kHz (KRF-V8060D)
Usable sensitivity (30% mod, S/N 20 dB)........................................................................ 16 µV / (600 µV/m)
Signal to noise ratio (30% mod, 400 Hz).......................................................... 50 dB (60 dBµ VEMF input)
GENERALPower consumption VR-6060 ....................................................... 3 A
KRF-V8060D ........................................... 300 WAC outlet
SWITCHED VR-6060 ..................... (total 150 W, 1.25 A max.)KRF-V8060D ............................. (total 90 W max.)
Dimensions ..................................................... W : 440 mm (17-5/16")H : 159 mm (6-1/4")D : 392 mm (15-7/16")
Weight (Net)VR-6060 ................................................................ 9.4 kg (20.7 lb)KRF-V8060D ........................................................ 10.0 kg (22.0 lb)
•VR6060/35-44/EN 3/11/02, 8:55 PM43
44 EN
For your recordsRecord the serial number, found on the back of the unit, in the spacesdesignated on the warranty card, and in the space provided below. Referto the model and serial numbers whenever you call upon your dealer forinformation or service on this product.
Model__________________ Serial Number ________________________
•VR6060/35-44/EN 3/11/02, 8:55 PM44