Architectural Design Elements for the Home Exterior

Installing your Signature Décor Windows

Installation Procedure:

Your Window Kit includes:

Tools required for installation:

2 Window Frames w/ plexiglas inserts12 Phillips-head 1 1/2” screws12 Rubber WashersFull-size paper template

• Electric drill with 1/8” drill bit• Phillips Screwdriver• Tape Measure• Masking Tape• Level• Step stool or ladder

1. Verify that your Signature Décor Windows will fit properly on your garage door. (Refer to Coach House Accents® document “Garage Door Specifications” available on our website.)

2. Place your full-size paper template onto the garage door where desired, using a tape measure to ensure that the template is positioned properly on the door panels. (See diagram below) Tape the paper template in place on the door panel.

3. Drill 1/8-inch pilot holes in the six locations indicated on the template. Drill through the paper into the door, then remove the paper template.

4. Lay the window face-down on a smooth surface that will not scratch the window, and remove the protective film from the back of the Plexiglas.

5. Insert the six screws into the mounting holes from the front of the panel, and press the rubber washers onto the screw threads from the back side, all the way to the window panel.

6. Lift the window up to the door panel, and align the protruding screws to the pilot holes. Tighten the screws to fasten the window to the

door. TAKE CARE NOT TO OVER-TIGHTEN, which can pull the threads from the holes or distort the panel.

Repeat this process for your other window panels.Center over panels

Signature DécorSimulated Window

Installation Template

NOTE: ALWAYS MEASURE YOUR DOOR PANEL BEFORE YOU START TO BE SURE!Manufacturers may change stamping sizes due to model and design changes. Coach House Accents® cannot be responsible for these changes.

Shown is a short-panel door. Use the same technique for long-panel or flat-panel doors.

MKTG009A v.020112

Distributed by Amarr Garage Doors1.800.503.DOORwww.amarr.com

Architectural Design Elements for the Home Exterior

Installing Your Decorative Hardware

NOTE: ALWAYS MEASURE YOUR DOOR PANEL BEFORE YOU START TO BE SURE!Manufacturers may change stamping sizes due to model and design changes. Coach House Accents® cannot be responsible for these changes.

Installation Procedure:

Your Hardware Kit includes:

Tools required for installation:

2 Handles + 4 Hinges 32 Phillips-head 1 1/2” screwsInstallation Instructions

• Electric drill with 1/8” drill bit• Phillips Screwdriver• Tape Measure• Level• Step stool or ladder

1. Verify that your Coach House Accents® products will fit properly on your garage door. (For more information, please refer to our website.)

2. Your garage door should be completely closed while installing this product to ensure proper alignment.

To install Decorative Hinges:

3. Position the hinges in the center of the horizontal surface of the garage door panel as shown below. Use your level to ensure that the mounting holes line

up properly. Also be sure that the edge of the hinge does not interfere with the weatherstripping at the edge of the garage door opening.

4. Drill 1/8-inch pilot holes into the door panel using the mounting holes in the hinge as a guide.

5. Fasten the hinges with the stainless-steel screws provided with your hardware kit.

Repeat this process for your other three hinges.

To install Decorative Handles:

6. First, measure the center vertical panel of your garage door to see if two handles will fit side-by-side. (All kits come with two handles.) If this surface measures 7” wide or more, you can position the pair carefully within that section. If not, center a single handle on the vertical surface as shown below.

7. Drill 1/8-inch pilot holes into the door panel using the mounting holes in the handles as a guide.

8. Fasten the handles with the stainless-steel screws provided with your hardware kit.

Repeat this process for the second handle.

MKTG004A v. 020112

“Stamping Area”

7 inchMinimumfor two handles

3 inch Minimumfor one handle

2 5/8 inchMinimum

Signature SeriesDecorative Hinge

Make sure edge of hinge does notinterfere with the weather-strip.

Distributed by Amarr Garage Doors1.800.503.DOORwww.amarr.com