installing the firewire drivers on the fmpc

7/31/2019 Installing the Firewire Drivers on the Fmpc

1/14


2/14

2007-2008 FUJIFILM Corporation. All rights reserved.2

8 Click OK.

The system reboots.

9 Before plugging in the printers FireWire cable, be sure the printer is still off.

10 Plug in the printers FireWire cable to the FMPC FireWire #2 card port. FireWire cablesfrom the LP and the SP need to be in separate cards. (See screenshot on page Error!Bookmark not defined.).

>>> To install FireWire drivers for the LP5500, LP5700, and LP5900 printers:

To install FireWire drivers for the LP 5500, LP 5700, and LP 5900 printers, follow theinstructions beginning on this page.

To install FireWire drivers for the LP 1500, LP 2000, and LP 2500 printers, follow the

instructions beginning on page 8.

1 Turn the printer switch to ON.

Wait for the LCD screen to display Frontier

2 Move the printer switchtoSTANDBY.

3 Wait until the LCD displaysStandby.

A Welcome to the Found NewHardware Wizard screendisplays.

4 Select Install the software automatically (Recommended).


3/14


5 Remove the CD from the CD-ROM drive.

6 Click Next >.

The Completing the FoundNew Hardware Wizard screendisplays.

7 Click Finish.

The wizard closes.

8 From Windows, select Start >Run.

The Run dialog box opens.

9 Type VDEntry in the Open field.

10 Click OK.


4/14


The VirtualDriverEntry dialogbox opens.

11 Change the IEEE1394 BusID to0.

Note: It is important that youtype 0 in the text box to change

the IEEE1394 BusID beforemoving on to the next step.

12 Click Regist..

13 The Welcome to the FoundNew Hardware Wizard screen

displays.


15 Click Next >.


5/14



16 Click Finish.

The wizard closes.

17 Close the VirtualDriverEntry dialog box.

18 On the FMPC, select Start > Settings > Network Connections.

The Network Connectionswindow opens.

19 Disconnect the printers FireWire cable from the back of the FMPC.


6/14


7/14


A context menu opens.

24 Select Properties.

The 1394 Connection Properties dialog box opens.

25 In the Internet Protocol(TCP/IP) Properties section,select Internet Protocol(TCP/IP).

26 Click the Properties button.


8/14


The Internet Protocol (TCP/IP)Properties dialog box opens.

27 Select Use the following IP address and enter the following:

IP address: 192.168.0.10

Subnet mask: 255.255.255.0

28 Click OK.

The Internet Protocol (TCP/IP) Properties dialog box closes, and the 1394 Connection 2Properties dialog box returns to focus.

29 Click OK.

The Properties dialog boxcloses.

30 Re-connect the printers FireWire cable from the port where it was unplugged.

31 Click to close the window.


9/14


10/14


The drivers install and theCompleting theFound NewHardware Wizardscreendisplays.

6 Click Finish.Note:

The following steps only need to be completed if you are installing with an SP3000scanner.

Note: You will have to run and complete VDEntry to install the SP-3000 driver. This is to be doneon the FMPC/LPC.

1 From Windows, select Start >Run.

The Run dialog box opens.

2 EnterVDEntry in the Openfield.

3 Click OK.


11/14


The VirtualDriverEntry dialogbox opens.

32 Change the IEEE1394 BusID to0.

Note: It is important that youtype 0 in the text box to change

the IEEE1394 BusID beforemoving on to the next step.

33 Click Regist..

The Welcome to the FoundNew Hardware Wizard screen

displays.


5 Click Next >.


12/14



6 Click Finish. The wizard closes.

7 Close the VirtualDriverEntry dialog box.

8 On the FMPC, select Start > Settings > Network Connections.

9 The Network Connectionswindow opens.


13/14


10 On the FMPC, select Start >Settings > NetworkConnections.

The Network Connections

window displays.

11 Right-click one of the 1394Connections listed.

A context menu opens.

Select Disable.

Repeat these steps for yoursecond 1394 connection.

Note: Disabling the connectiontakes a few seconds. Thescreen may need to bemanually refreshed by pressingF5 to reflect the disabledconnection.

(The scanner does not use thenetworking capabilities ofFireWire, and must be disabledto allow the scanner to connect.)

At this time both 1394Connections display asDisabled.

Note: if a 300 series printer is

being installed, such as anLP1500, 2000, or 2500, theTCP/IP protocol over 1394 netadapter needs to be disabled asit may lead to communicationerrors during firmware loading.

Only 500 series printers utilizethis protocol for communication.


14/14


12 Close the network connectionswindow.

installing the firewire drivers on the fmpc

Documents