installation use - schneider electricmt.schneider-electric.be/op_main/sepam/3141951uk.pdf ·...

SFT 2801

SFT 2801 - Installation - Use 3 141 951 A - D 1

Installation

Use

contents


introduction 3

ACE 900 connection kit 4

graphical interface 5

user guide 7

reading characteristics 12

operations on characteristics Erreur! Signet non défini.5

disturbance records 18

application identification 1

printing 1

installing SFT 2801 22

appendix 1 SFT 2801 keys / keyboard equivalencies 28

appendix 2 example of Sepam 2000 parameter readout 29

introduction


descriptionThe SFT 2801 application is a software tool that may be used instead ofthe "TSM 2001 pocket terminal" under Windows™ 95, 98 and NT 4.0.

Furthermore, the SFT 2801 application provides additional functions forreading, printing and storage of Sepam 2000 parameters and forretrieving disturbance records.

It is installed on a PC connected to the front of Sepam 2000 via anadapter.

functionsAll the TSM 2001 pocket terminal functions are included in the SFT2801 application.

The functions used to read and set the various Sepam 2000 parameters(measurements, protections, etc.) in the software version of TSM 2001are similar to the pocket terminal functions (dialog via menus and sub-menus; cf manual ref. 3140750).

The following additional functions are made available by the softwareversion :

• general readout of Sepam 2000 characteristics.

• saving and restoring of all Sepam 2000 characteristics.

• printing of a report containing the values of all the Sepam 2000characteristics.

• retrieval of a disturbance record

• saving of a disturbance record

required set-up• The minimum set-up is given in the installation section.

ACE 900 connection kit


kit contentsThe ACE 900 connection kit supplied with SFT 2801 is made up of :

• 1 Sepam - RS232 interface

• 1 PC - interface serial connection cord

connectionThe interface should be plugged into the inlet on the front of Sepam2000, behind the small flap door. The other end is connected to theCOM1 or COM2 communication port (whichever was selected at thetime of installation) on the PC.

interface should be plugged into the inlet

front of Sepam

It is mandatory for the ACE 900 connection kit supplied in SFT 2801kit to be used to connect the PC and Sepam 2000.

The use of any other cord is liable to cause Sepam 2000 operatingdifficulties.

environmentalspecifications

dielectricdielectric withstand IEC 60255-4/5 0.5kVeff CM1.2/50µs impulse wave IEC 60255-4/5 1kV MC , 0.5kV DMclimaticoperation IEC 60068-2 -5 to 55°Cstorage IEC 60068-2 -25 to 70°Celectromagneticradiation IEC 60255-22-3 30V/m IEC 61000-4-3 10 V/melectrostatic discharge IEC 60255-22-2 8kV1MHz damped oscillatingwave

IEC 60255-22-1 1kV MC , 0.5kV DM

5ns fast transient IEC 60255-22-4 1kV CM, DM direct coupling4kV CM capacitive coupling

CM = common mode DM = differential mode

graphical interface


designThe SFT 2801 application is materialized in Windows™ by a graphicalinterface (window) representing the TSM 2001 pocket terminal.

A B C D

A the title bar displays the name of the application: "SFT 2801"followed by identification of the Sepam when a Sepam is connectedto the PC.

B the menu bar gives access to the SFT 2801 special features

C the display field may be one of two types :• an SFT 2801 information screen• an TSM 2001 type screen, with four 20-character lines.

D control buttons which match the TSM 2001 pocket terminalkeyboard keys

display zoneThe software version display is the same as the TSM 2001 pocketterminal display: four 20-character lines. The same blinking also occurs.The cursor at the beginning of a line is indicated by a blinking ">"character.

SFT 2801 keyboardPressing a key on the SFT 2801 keyboard may be reproduced in twoways :

• using the mouse, by clicking on the corresponding button.

graphical interface


• using the PC keyboard, by pressing the corresponding key. The keyis generally identified by the name which appears on the controlbutton on the SFT 2801 keyboard (cf Appendix 1).

behaviourThe SFT 2801 application complies with the usual MS-Windows rulesand operating procedures, which are not reminded here. In case ofnecessity, please refer to the manuals supplied with your computer.

user guide


starting up theapplication

In the Windows Program Manager, double-click on the SFT 2801 icon.The window below appears in the centre of the screen.

When pressing Enter, the following warning window is displayed.

user guide


When this message is acknowledged, the SFT 2801 main window isdisplayed.

PC/Sepam dialog is not activated until communication has beeninitialized.

user guide


customization ofapplication

This function allows to customize the program language and the serialI/O port of computer connected to Sepam.

To change the language, select Customization then Languages.Select then the new language.

To change the I/O port, select Customization then PC port name.Select then the new port.

user guide


initializingcommunication

To initialize communication between the PC and Sepam, click on the

control button or press function key F5 on the PC

keyboard.

Although the window is displayed, it remains inactive for 5 to 10seconds, during which time no action is possible. The application needsthis time to test the Sepam to obtain its identifier.

The window becomes active when the reading of Sepam identificationhas been completed : the title bar then displays the identifier of theSepam connected to the PC in addition to the application name. The"Identifying" message disappears from the display field, giving way tothe usual Sepam opening menu.

In this status, the user may use the software version of TSM 2001 inexactly the same way as the pocket terminal.

user guide


scanning SepamAs of the time that communication is initialized, SFT 2801 continuallyscans the link with the Sepam connected to the PC on which theapplication is running.

If the Sepam connection is down (connection cord damaged or Sepamdisconnected or not energized...), SFT 2801 detects interrupted dialogand displays :

The graphical interface is inactive until the user validates the messagewindow by clicking on the "OK" button. Communication must then beinitialized again.

reading characteristics


descriptionThis function is a general readout of Sepam characteristics. It works byreading the following Sepam parameters :

• Sepam identification and software versions ("About Sepam" choice).

• Sepam settings ("Status" choice).

• Protection settings ("Protections" choice).

• Parameters ("Program logic" and "Parameters" choice).

• Timers ("Program logic" and "Timer") choice.

activateTo activate reading of all the characteristics, select the Charact. ThenRead item in the SFT 2801 menu bar.

The SFT 2801 graphical interface becomes inactive and the followingmessage is displayed :

The Sepam characteristics reading operation takes about 2 to 6minutes, depending on the Sepam configuration. The operation may beinterrupted at any time by clicking on the "Cancel" button or by pressingthe "Return" key on the PC keyboard.

When the operation is interrupted, the SFT 2801 window becomesactive again, the dialog between the PC and Sepam is reinitialized andthe Sepam opening menu appears again in the display field.



viewIf the characteristics reading operation is successfully completed, a fullscreen size characteristics display window appears.

A slider bar (scroll bar) located on the right-hand side of the display fieldmay be used to scroll its contents vertically.

The window also includes 3 control buttons :

record

To save the characteristics that have been read, click on the "Record"control button.

A dialog box is then displayed. This box is used to choose a name toidentify the characteristics that will be saved.

The name of the Sepam being examined is proposed (the name appearsin the title bar of the main screen and the characteristics displaywindow).

When several Sepams have the same name (as in the case of thestandard applicationsof the Sepam 2000 catalogue), it is necessary tomodify the proposed name to record and save the characteristics of theSepams which have the same name.



Once the user has confirmed the name to be used for the save, the textof the displayed characteristics is stored on the PC disk and may beretrieved for subsequent printing or saving operations.

If several storage operations are carried out for the same Sepam, onlythe most recent one is kept. The date of storage of the characteristicsis memorized.

The data structure used is a text file, the contents of which are an exactreplica of the text displayed in the display window (cf example inAppendix 2).

The name given for the stored data will appear on the first page of theprintout of characteristics under the heading "Sepam Name". The actualname of the Sepam application is given in the "Identification" section bythe text located under the name "SFT 2800".

print

To print the characteristics that have been read, click the "Print" controlbutton.

This command is only available after the user has stored thecharacteristics.

The printing format is virtually the same as the display and storageformats. It also includes a cover page giving identification of the Sepamand the setting dates.

Refer to the "print" chapter for more information on printing.

cancel

To close the characteristics display window, click on the "Cancel"control button or double-click on the system menu box.

The SFT 2801 window then takes over again and the Sepam openingmenu appears again in the display field.

operations on characteristics


The Charact. item in the SFT 2801 menu bar gives access to variousfunctions operating on the previously saved characteristics.

printThis option may be used to print Sepam characteristics that have beenpreviously recorded from the characteristics display window (cf chapterentitled "reading characteristics").

The print window appears in the centre of the screen, which lists thepreviously recorded Sepams.

Select the Sepam that you want to print and click on the "Validate"button to start printing.

A "Cancel" button may be used to return to the SFT 2801 graphicalinterface without printing.

Refer to the chapter entitled "Printing" for more information on theprinting procedure.

saveSepam saving enables the user to transfer the information regarding theparameters of one or more Sepams, previously stored using the"Record" command (Cf "reading characteristics" chapt.), to any backupmedium recognized by Windows™ (diskette or other).The save windowis displayed in the centre of the screen.



• in the "From" field, select each of the Sepams that you wish to save.

• in the "To" field, select the destination medium and/or directory. If thedesired directory is not found, you must create it.

A list displays the Sepams that have already been saved in theselected backup directory (indicated in the "Directory" string), with thesave dates.

• click on the "Validate" button to start the save operation.

The "Cancel" button may be used to return to the SFT 2801 graphicalinterface without saving.

restoreSepam restoring enables the user to transfer the information related tothe parameters of one or more Sepams from a backup medium to theSFT 2801.

The restore window is displayed in the centre of the screen.

• in the "From" field, select the restore source medium and/or directory,and then the Sepams to be restored (the current path to the sourcemedium is indicated in the "Directory" string).



• in the "To" field, a list indicates the Sepams already included in theSFT 2801.

• click on the "Validate" button to begin restoring.

The "Cancel" button may be used to return to the SFT 2801 graphicalinterface without restoring.

deleteThis option is used to delete previously recorded information related tothe characteristics of one or more Sepams, when that information is nolonger of any use.

The delete window appears in the centre of the screen.

• select the Sepams that you wish to delete, in the list of previouslyrecorded Sepams.

• click on the "Validate" button to delete the characteristics of theselected Sepams.

The "Cancel" button may be used to return to the SFT 2801 graphicalinterface.

disturbance records


The Disturb. item in the SFT 2801 menu bar gives access to variousfunctions operating on disturbance records.

recoverThis choice is used to retrieve a disturbance record from the Sepam.The following window appears, which lists the available records :

• select the record that you want to read

• type in the name to identify the record that will be retrieved

• click on the "Validate" button to start reading

The "Cancel" button may be used to return to the SFT 2801 graphicalinterface without reading.

The SFT 2801 graphical interface becomes inactive and the followingmessage is displayed :

The disturbance record reading operation takes about 3 minutes. Theoperation may be interrupted at any time by clicking on the "Cancel"button or by pressing the "Return" key on the PC keyboard.

When the operation is completed (or cancelled), the SFT 2801 windowbecomes active again, the dialog between the PC and Sepam isreinitialized and the Sepam opening menu appears again in the displayfield.

disturbance records


saveThis option may be used to transfer the previously retrieved disturbancerecord to any backup medium recognized by MS-DOS (diskette orother). It works the same way as the save option for Sepamcharacteristics. Please refer to the corresponding chapter.

deleteThis option is used to delete previously retrieved disturbance records,when they are no longer of any use.It works the same way as the deleteoption for Sepam characteristics. Please refer to the correspondingchapter.

SFT 2826To display the retrieved disturbance records, you may use the SFT 2826application (or any COMTRADE compliant application). The disturbancerecord files are placed in the "\REG2000" subdirectory of the directory inwhich the SFT 2801 application has been installed.

application identification


SFT 2801 softwareversion

When you select the ? then About... option in the SFT 2801 menu bar,a window giving various items of information on the SFT 2801 softwarepackage is displayed.

printing


introductionBefore printing, you must first check that Windows is set up correctlyfor the type of printing device to which your work station is connected.For further information, refer to the Windows User's Guide.

printPrinting of Sepam characteristics is accessed from the parameterdisplay window (Cf chapter entitled "reading parameters") or via thePrint option in the Charact. menu bar item.

The printed file is sent to the Windwos printer manager.

error messagesDifferent types of errors may occur during printing. In such a case, amessage displays the type of error encountered, and printing isautomatically interrupted.

The main types of errors are the following :

• a general error related to the printer (printer not connected or not setup correctly, out of paper ...).

• impossible to use printer. This error occurs when the print driver oroutput port, chosen via the Windows control panel, is incorrect. Referto the Windows manual.

• out of disk space: temporary files are created by Windows, and thecurrent disk unit must have sufficient space available for those files.

installing SFT 2801


general information

The program is very simple to use and does not require any priorknowledge of your computer or computer technology.

The program allows to install together or separately the SFT 2801 and SFT2821 software.

The installation diskettes are common for these products.

set-upThe minimum hardware set-up required to run the SFT2821 software is asfollows:n PC compatible microcomputer:

r Pentium type

r 133 MHz

r 32 Mb Ram (minimum)

r graphic display (EGA, VGA, Super VGA), minimum resolution 800 by600 pixels,

r a 3"½ diskette drive (1.44 Mb)

r a hard disk (4 Mb available)

r an available RS232 communication port (COM1 or COM2)

n system:

r Windows™ 95 (version 708 or later version) or Windows™ 98

r or Windows™ NT 4.0 version 1382 with pack 3 or later version and rightsto modify Window NT system files.

n a printer (optional)

starting the installation• Insert diskette N°1 of the installation package in your disk drive.

• In the menu Start select Settings and then Control Panel.

• Select the Add/Remove Programs function.

• Click on the Install button in the form Install/Uninstall

• Follows the instruction from Windows to install the program from theinstallation diskette.

installing SFT 2801


installation start-upA start-up program will copy the files needed to run theSFT2801/SFT2821 installation program.

It’s important that all the Windows applications are closed during theinstallation process to avoid access conflicts to system files.By the way, if a conflict occurs , a message will appear.

In this case Close all the applications and restart the installation.If the conflict is still present, then select the Ignore button on thewindow and continue the installation.

It’s also possible that the installaton requires the reboot of your systemfor the upgraded system files to be taken into account. In this case,perform the reboot and restart the installation from the beginning.

canceling duringinstallation

It is possible to cancel the installation procedure at any time, in which caseeverything that has been created by the program (files, directory, icons,shortcuts,…) up to the cancellation is automatically deleted.

installing SFT 2801


start-up screenFirst of all, the screen asks the user to close the applications beforecontinuing the installation of the SFT2801 software. In this case, the userchooses "Exit installation".The installation procedure must be started over from the beginning.

In addition, the screen may be used to choose the installation language,which will also be the default language of the SFT 2801 program.

choosing the installationdirectory

The following screen is used to select the installation directory.

The directory proposed by default is c:\Program Files\Schneider\.

The SFT2801 is installed in a SFT2801 directory which is created in thisdirectory by default.With the "Change directory" button, it is possible to choose another defaultdirectory in which the SFT2801 directory will be created. If the defaultdirectory does not exist, it is created.

installing SFT 2801


choosing the programto be installed

SFT2801 and SFT2821 may be installed at the same time or separately. Ifthe SFT2821 software is selected as well, it is installed in the directorychosen in the previous screen, in an SFT2821 subdirectory.

checking disk spaceAt this stage of the installation, the software checks that the computer hasenough disk space for the selected software to be installed.

installing SFT 2801


choosing the group ofprograms

This screen is sued to choose the group of programs that will be created inthe Start / Programs menu. The choice proposed by default is Schneider. According to the programs selected for the installation, one or two iconsSFT2801 and SFT2821 are created in the new group.

copying files

The program copies the files required for the chosen program or programs.

installing SFT 2801


The application may propose you to keep a file which is more recent onyour disk than the version on diskette.

In this case, it’s recommended that you keep your existing file. Inparticular the SFT2801.INI file which contents the personalized settingsof your program.

end of installationThe system files are then updated.The program icons are created.

A message informs you that the software has been installed correctly.

Deinstallation Before deinstalling the software, the user should check that the SFT2801software is not running. To deinstall: n in the Start menu, choose Settings and then Control Panel, n click on Add /Delete program, n go to the Install /Deinstall tab, n select the software in the list to be deinstalled, n click on add/delete, n confirm deinstallation. Windows™ can only deinstall files that have been installed using theinstallation software. If you want the deinstallation tool to actually delete allthe directories in the software, before starting deinstallation, you mustmanually delete all the files contained in SFT2801\reg2000 for the SFT2801program.


appendix 1 SFT 2801 keys / keyboard equivalencies

SFT 2801 keys PC keyboard

F1 function key

UP arrow key

DOWN arrow key

"9" number key

"8" number key

"7" number key

"6" number key

"5" number key

"4" number key

"3" number key

"2" number key

"1" number key

"0" number key

"." decimal point key

F2 function key

F3 function key

"-" minus key

"+" plus key

F4 function key

return key

F5 Initialize F5 function key


appendix 2 example of Sepam 2000 parameter readout

This example gives an idea of the format in which Sepam parameters are displayed, recorded orprinted :

------------------------------------------------------------------------------

IDENTIFICATION

------------------------------------------------------------------------------ SFT 2800 : PROGRAM LOGIC : PROGRAM LOGIC VALDEMF ATC : DEPDISJ : program dated : SFT 2800 : 94.29 : Central switchboard : 94/10/24 15:56 : model : Logipam : 94.28------------------------------------------------------------------------------

STATUS

------------------------------------------------------------------------------ RATED FREQUENCY : PHASE TC RATIO : E/F SENSOR Fn = 50 Hz : In = 90 A : Ino = CT 30A : Ib = 90 A : : Number = I1-I2-I3 :------------------------------------------------------------------------------ MAX DEMAND INTERV. : VT RATIO : VT RATIO Interval= 10 mn : Number = 3U : Vnso = Uns/1.732 : Unp = 20 kV : : Uns = 100 V :------------------------------------------------------------------------------ POWER FLOW SENSE : JBUS COMMUNICATION : JBUS COMMUNICATION Type = Incomer : Speed = 9600 bauds : CPT2 = 0 : Address= 1 : CPT9 = 0 : Parity = Even :------------------------------------------------------------------------------ TIME TAGGING : TIME TAGGING : TIME TAGGING Synchro.=ETOR I21 : KTS 1- 8=0000 0000 : KTS25-32=0000 0000 : KTS 9-16=0000 0000 : : KTS17-24=0000 0000 :------------------------------------------------------------------------------ TIME TAGGING : I1 -I2 = 00 : I11-I18= 0000 0000 : I21-I28= 0000 0000 :------------------------------------------------------------------------------



------------------------------------------------------------------------------

PROTECTIONS

------------------------------------------------------------------------------ O/C F011 : O/L F012 : E/F F081 Curve = Definite : Curve = Definite : Curve = Definite Is = 500 A : Is = 600 A : Iso = 60 A T = 500 ms : T = 3 s : T = 1 s------------------------------------------------------------------------------ U/current F221 : O/V F281 : U/V F341 Is = 80 %Ib : Us = 16 kV : Us = 1.5 kV T = 5 s : T = 3 s : T = 2 s : :------------------------------------------------------------------------------ brdl F441 : Unbalance F451 : Unbalance F451 Is = 115 %Ib : Curve = Definite : Ii = 0.0 %Ib ST = 8 s : Is = 60 %Ib : LT = 2 s : T = 5 s :------------------------------------------------------------------------------ ndtf F421 : ndtf F421 : therm F431 N start= 999 : T = 500 ms : OL1 = 105 % H start= 5 : N.rest = 5 : OL2 = 120 % C start= 5 : : K = Average------------------------------------------------------------------------------ therm F431 : T1 = 5 mn : T2 = 5 mn : E = 0.0 % :------------------------------------------------------------------------------



------------------------------------------------------------------------------

PARAMETERS

------------------------------------------------------------------------------ KP 1 = 1 KP 2 = 0 KP 3 = 0 KP 4 = 0 KP 5 = 0 KP 6 = 0 KP 7 = 0 KP 8 = 0 KP 9 = 0 KP 10 = 0 KP 11 = 0 KP 12 = 0 KP 13 = 0 KP 14 = 0 KP 15 = 0 KP 16 = 0------------------------------------------------------------------------------

TIMERS

------------------------------------------------------------------------------ T1 = 100 ms 0 : T21 = 100 ms 0 : T41 = 100 ms 0 T2 = 100 ms 0 : T22 = 100 ms 0 : T42 = 100 ms 0 T3 = 100 ms 0 : T23 = 200 ms 0 : T43 = 100 ms 0 T4 = 2 s 0 : T24 = 250 ms 0 : T44 = 250 ms 0 T5 = 250 ms 0 : T25 = 250 ms 0 : T45 = 250 ms 0 T6 = 250 ms 0 : T26 = 250 ms 0 : T46 = 250 ms 0 T7 = 1.2 s 0 : T27 = 1.2 s 0 : T47 = 1.2 s 0 T8 = 750 ms 0 : T28 = 1.2 s 0 : T48 = 750 ms 0 T9 = 1.2 s 0 : T29 = 2 s 0 : T49 = 100 ms 0 T10 = 100 ms 0 : T30 = 200 ms 0 : T50 = 200 ms 0 T11 = 200 ms 0 : T33 = 200 ms 0 : T51 = 200 ms 0 T12 = 200 ms 0 : T31 = 200 ms 0 : T52 = 200 ms 0 T13 = 200 ms 0 : T33 = 200 ms 0 : T53 = 200 ms 0 T14 = 200 ms 0 : T34 = 200 ms 0 : T54 = 200 ms 0 T15 = 200 ms 0 : T35 = 200 ms 0 : T55 = 200 ms 0 T16 = 200 ms 0 : T36 = 200 ms 0 : T56 = 200 ms 0 T17 = 200 ms 0 : T37 = 50 ms 0 : T57 = 200 ms 0 T18 = 200 ms 0 : T38 = 200 ms 0 : T58 = 200 ms 0 T19 = 200 ms 0 : T39 = 200 ms 0 : T59 = 200 ms 0 T20 = 200 ms 0 : T40 = 200 ms 0 : T60 = 200 ms 0------------------------------------------------------------------------------

installation use - schneider electricmt.schneider-electric.be/op_main/sepam/3141951uk.pdf ·...

Documents