Connecting your Kube™

INSTALLATION, REGISTRATION AND OTHER IMPORTANT THINGS

TM

04

Connecting Your Kube™

Installation pre-checkThe Kube's installation kit includes adaptors for 15mm copper pipe plumbing configuration. Using the supplied fitting kit will ensure your installation conforms to water regulations. For any further assistance please contact Kinetico on 0800 804 74 74. Follow these guidelines as you install the Kube Advanced Water Filtration System.

CAUTION: Do not use the Kube with water that is microbiologically unsafe or of unknown quality.

• The Kube Advanced Water Filtration System must be properly located and installed in accordance with the Installation Instructions before it is used.

• For certified performance, install the Kube with a 8.3 litres per minute rated tap.

• Use the Kube on a safe-to-drink, COLD water supply only. The Kube will not purify water or make unsafe water safe to drink.

• Do not install on HOT WATER supply.

• Do not install the Kube outside or anywhere it will be exposed to sunlight.

• Protect the Kube and piping from freezing. Water freezing in the system may damage it.

• The temperature of the water supply to the Kube must be above 2°C.

• The Kube will withstand up to 8 bar water pressure.

• See the Performance Data section for additional details (page 21).

• To order replacement filters visit www.kubewater.co.uk

If in doubt, give us a call on 0800 804 74 74, we are here to help.

05

www.kubewater.co.uk

What's in the box?Kube Advanced Water Filtration System

Kube Installation Kit

2 High-Capacity Filtration Cartridges

1

2

3

Kube Life Guide

3

A - 3/8" Plastic Tubing

B - CONNECTION 1 15mm Compression, Isolation Valve, NRV, 3/8" Push Fit

C - CONNECTION 2 15mm Compression, 3/8" Push Fit

07

www.kubewater.co.uk

Preparing for Kube

2 x adjustable wrenches utility knife dry towel or paper towels

To complete installation you should have a basic knowledge of plumbing fittings and the following tools:

pipe cutter

Customer support

The Kinetico customer services team is always on hand to assist and help you with any questions or support you require. For all enquiries, please send an e-mail to info@kinetico.co.uk or contact us on: 0800 804 74 74. Please also check out our FAQs, see page 18.

tape measure

08

Connecting Your Kube™

STEP 1Check the clearanceClean out the area under your sink, and ensure that there is enough room for your Kube.

Make sure the back of the Kube isn't touching the back of the cabinet; you'll need space for the connections.

Connecting Kube

STEP 2Shut off the waterIsolate the cold supply to your cold water tap. Open tap and drain residual water to ensure it is fully isolated.

STEP 3Disconnect the cold water supplyLocate 15mm ø copper cold water supply pipe. Select suitable position to remove 200mm of pipe. Cut out the section using a pipe cutter. Connections vary, please contact Kinetico should you require assistance or advice.

TIP: Use towel or bowl to collect water remaining in the pipe work.

STEP 4Connect the adaptersSUPPLY PIPE: Fit CONNECTION 1 using 15mm compression isolation valve fitting. Ensure isolation is closed.

TAP FEED: Fit CONNECTION 2 using 15mm compression fitting.

HOT WATER SUPPLY

COLD WATER SUPPLY

CUT 200MM OF PIPE

COLD WATER SUPPLY

CONNECTION 1 CONNECTION 2

TO COLD WATER TAP

Please note: Diagram is an example only. Other plumbing features have been omitted for clarity of Kube placement.

09

www.kubewater.co.uk

STEP 5Measure the tubingDetermine two lengths of the tubing for:

CONNECTION 1 to the Kube inlet elbow. CONNECTION 2 to the Kube outlet elbow.

TIP: Allow sufficient hose length to prevent sharp bends or kinked tubing.

STEP 6Cut the tubingDo not kink the tubing. Using a sharp utility knife, make a perpendicular cut to your measured length of tubing.

STEP 7Connect the tubingTake one piece of pre-cut tubing. Connect one end into CONNECTION 1 and the other end into the inlet elbow.

Take the second piece of pre-cut tubing. Connect one end into the outlet elbow and the other end into CONNECTION 2.

STEP 8Check the tubingFirmly push the 3/8" tubing into all fittings. Push and pull the tubing to ensure the tubing has been installed properly and is locked in place. To remove tubing, depress and hold the collet then pull the tubing out.

ENGAGEMENT 3/4"

INSERT TUBING

CONNECTION 1

CONNECTION 2

COLD WATER SUPPLY

OUTLET ELBOW

INLET ELBOW

COLD WATER TAP

10

Connecting Your Kube™

OPEN

STEP 9Connect the cartridgesAlign the tabs on the cartridge body with the tab holes on the face of the Kube. Fully insert the cartridge, then twist to lock into place.

TIP: It will be like fitting a key into a lock. Twist clockwise to lock in place. The raised area on the end of the cartridge cap should be lined up with the lock icon . Do the same with the second cartridge.

STEP 10Turn on water then turn on your cold tapTurn your cold water supply on slowly and watch closely to ensure there are no leaks at the shut off valve. If you see a leak, turn it off again and double check connections.

Turn the handle on CONNECTION 1 to open the valve. Check all connections including the elbows on the back of the unit for leaks.

STEP 11Put your Kube to workTurn the blue by-pass knob until the white indicator points to the filtered water icon

TIP: The knob will not turn unless both cartridges are completely installed.

STEP 12Flush cold waterTurn on your cold water for about five minutes to activate your filter cartridges.

While you wait, double check all connections again to make sure nothing is leaking.

After five minutes turn off your tap.

Wait ten minutes and then turn the cold water back on for another three minutes.

After three minutes turn off your tap.

You are now ready to enjoy the benefits of your new Kube!Turn on your cold water tap.

20

Connecting Your Kube™

WarrantyYour Kube comes with a 1 Year Limited Warranty. It is valid for one year from the original date of purchase and covers any defect in materials or workmanship in the manufactured product.

This warranty does not cover:• Filter cartridges after 30 days from date of purchase.

• Product failure if it is abused, misused, altered, used commercially or used for other than the intended purpose.

• Use of this product where water is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected water that may contain filterable cysts.

• Damage to the product caused by accident, fire, floods or acts of nature.

• Incidental, consequential or special damages caused by possible defects with this appliance, its installation or repair.

How do I make a warranty claim?Call the Kube customer service line on 0800 804 74 74.

Terms and conditions:Kinetico products are manufactured to exacting standards and backed by the most comprehensive warranties in the industry. Your guarantee is in addition to and does not affect your statutory rights. The guarantee is valid from date of purchase and subject to the following conditions;

• The product is used for domestic purposes only in the United Kingdom.

• The product is installed and operated in accordance with our installation and operating instructions.

• The product is not subject to misuse or tampered with in any way.

• The guarantee has been registered within 28 days of purchase.

Within the guarantee period, should the product or any part thereof prove to be defective by reason of faulty workmanship or materials used in the manufacture of the product, we shall, at our option, either repair or replace the same free of charge provided the above conditions have been met and that the service work is carried out by Kinetico UK Ltd or by an Authorised Kinetico Agent. The guarantee on any exchanged parts or product will expire when the normal product guarantee expires.

21

www.kubewater.co.uk

Data & CertificationsA certified systemThe Kube is an amazing product, but don't just take our word for it. We put it through rigorous third party testing to ensure that it does everything we say it will.

The Kube Advanced Water Filtration System is Tested and Certified by WQA against NSF/ANSI 42, 53, 372, and CSA Standard B483.1. Conforms to NSF/ANSI 53 for VOC reduction.

See Performance Data Sheet for individual contaminants and reduction performance.

Performance dataModel Number KUBE14

Minimum Operating Temperature 2°C

Maximum Operating Temperature 49°C

Minimum Operating Pressure 35 PSI

Maximum Operating Pressure 125 PSI

Kube Replacement Filters Model Number KUBE14F1

22

Connecting Your Kube™

Simply brilliant, brilliantly simpleOur water experts put their very best thinking into engineering smarter products to bring families like yours the very best water. That's why millions of people around the world look to Kinetico for water treatment solutions.

Unmatched performanceFor more than 40 years, Kinetico has taken a smarter approach to solving water problems. Our systems treat water more efficiently, effectively and economically. With more contaminant removal and no variance in performance, you can be confident they will outperform other options available and provide you with clean, clear water for years and years. It’s why so many people around the world rely on our products. With Kinetico, every time you turn on your tap, you know you’re getting the best water - and only water.

Non-electricWater and electricity don’t mix, so Kinetico found a better way. Just like the Kube, Kinetico systems are powered by the force of moving water, not electricity. Our patented approach to water treatment eliminates the hassles of timers and computers - there’s nothing to plug in, and there are no electrical components to set, adjust, repair or replace. Our systems also monitor water use and only process your water when needed, eliminating waste.

Tailored to YouWe’ll be the first to admit that water treatment can be confusing. There are so many options. Choosing the right system for you and your home is tough, and so is finding the right company to work with. Kinetico takes the guesswork out of water treatment.

Your local Authorised Kinetico Dealer understands the water challenges in your area. First, they’ll thoroughly analyse your water supply, without cost or obligation to you. They’ll also inspect your plumbing and appliances and ask questions to understand your water needs. They will then suggest treatment options tailored to your water, home and budget. To find your local Authorised Kinetico Dealer, please visit www.kinetico.co.uk.

Kinetico

“Kube,” “Kinetico,” the Kube logo and the Kinetico logo are trademarks of Kinetico Incorporated, Newbury, Ohio.

©2015 Kinetico

www.kubewater.co.uk

facebook.com/kubewater

twitter.com/kubewater

Kinetico UK Ltd Bridge House, Park Gate Business Centre, Park Gate, Hants SO31 1FQ | www.kinetico.co.uk