installation & owners manual hercules ii 750...hercules ii 750 vertical platform lift manual...

P/N: 630-00046 RevD 111518

This manual has been provided to assist you with lift installation and operation.For further assistance please contact your authorized AmeriGlide dealer orAmeriGlide’s Technical Support Department.Tel: 866-378-6648Fax: 816-537-0641

Installation &Owners ManualHERCULES II 750Vertical Platform Lift

Dealer:

Serial No:

MODELS:AMGHERC750-4 AMGHERC750-6 AMGHERC750-8

AMGHERC750-10 AMGHERC750-12 AMGHERC750-14

Hercules II 750 Vertical Platform Lift Manual | www.Ameriglide.com | 866-378-66482 // 32

P/N: 630-00046 RevD 111518

TABLE OF CONTENT

Using the Manual _______________________________________ 3When You Receive the Lift Specifications ________________ 4Safety __________________________________________________ 4Code Requirements _____________________________________ 5Site Requirements ______________________________________ 5Required Tools__________________________________________ 5 Required Materials _____________________________________ 5Preparing to Install the Lift ______________________________ 6Controller Harness Connections _________________________ 6Installing the Platform __________________________________ 7Installing the Outer Guard Panel ________________________ 8Installing the Fixed Ramp _______________________________ 8Installing the Folding Ramp _____________________________ 9Anchoring the Lift ______________________________________ 10Setting the Limit Switches _____________________________ 11Verifying Operation of the Lift __________________________ 12Manual Override _______________________________________ 13Call-Sends (optional) _________________________________ 13Top Landing Gate (optional) ___________________________ 14EMI and Flush Strike (optional) ________________________ 15Platform Gate (optional) _______________________________ 16Fascia Panel (optional) ________________________________ 17Alarm __________________________________________________ 17Owner’s Section _______________________________________ 18Safety _________________________________________________ 19Controls _______________________________________________ 20Operating the Lift ______________________________________ 21Wiring _________________________________________________ 23Warranty ______________________________________________ 30

3 // 32Hercules II 750 Vertical Platform Lift Manual | www.Ameriglide.com | 866-378-6648

P/N: 630-00046 RevD 111518

Using the ManualThis manual will provide step by step instructions on how to install and operate your lift. Read and understand the entire manual before beginning to install the lift.

If you have any questions, contact Technical Service at 1-866-378-6648.

INDICATIONS OF USE STATEMENTThe Hercules II 750 vertical platform lift assists with the transfer of patients or mobility impaired persons, up and down between levels of a residential or private facility.

Hercules II 750 Vertical Platform Lift Manual | www.Ameriglide.com | 866-378-66484 // 32

P/N: 630-00046 RevD 111518

LIFT SPECIFICATIONS

WHEN YOU RECEIVE THE LIFT

• Check the lift for shipping damage. If you see any damage contact the freight carrier to file a damage claim.

• Verify that products match what’s described on the packing list attached to the exterior packaging.

SPECIFICATIONS

Payload Capacity 750 lbVertical Travel 53" - 171"Foot Print VariesPlatform Size 36" x 54" | 36" x 60" | 42" x 54" | 42" x 60"Input Voltage 115 VAC - 20 AControl Voltage 24 VAC or 24 VDCPlatform Speed 10' minMotor 1/ 3 HP - 90 VDC or 1/ 3 HP - 24 VDC

SAFETY

• Read all instructions in this manual before installing or operating the lift.• Do not exceed the maximum payload capacity of 750 lb.• Do not ride on the lift until it is anchored in place.• This product is designed only for lifting people and wheel chairs. Do not use it for

any other purpose.• Always wear eye protection while installing or servicing this product.• Always disconnect this product from the electrical source before servicing it.• Only use the fasteners supplied with this lift.• Do not wear loose clothing or jewelry when working on this product.• Do not disable any safety equipment or switches supplied with this lift.• Stay away from all drive train components while the lift is operating.


P/N: 630-00046 RevD 111518

REQUIREMENTS

WHEN YOU RECEIVE THE LIFT

• Check the lift for shipping damage. If you see any damage contact the freight carrier to file a damage claim.

• Verify that products match what’s described on the packing list attached to the exterior packaging.

SPECIFICATIONS

Payload Capacity 750 lbVertical Travel 53" - 171"Foot Print VariesPlatform Size 36" x 54" | 36" x 60" | 42" x 54" | 42" x 60"Input Voltage 115 VAC - 20 AControl Voltage 24 VAC or 24 VDCPlatform Speed 10' minMotor 1/ 3 HP - 90 VDC or 1/ 3 HP - 24 VDC

SAFETY

• Read all instructions in this manual before installing or operating the lift.• Do not exceed the maximum payload capacity of 750 lb.• Do not ride on the lift until it is anchored in place.• This product is designed only for lifting people and wheel chairs. Do not use it for

any other purpose.• Always wear eye protection while installing or servicing this product.• Always disconnect this product from the electrical source before servicing it.• Only use the fasteners supplied with this lift.• Do not wear loose clothing or jewelry when working on this product.• Do not disable any safety equipment or switches supplied with this lift.• Stay away from all drive train components while the lift is operating.

CODE REQUIREMENTS

Your lift has been designed to meet ASME A18.1 section 2 and CSA B44.1/ASME A17.5, with the addition of certain options. Code requirements for Vertical Platform lifts vary depending on location. It is the installers responsibility to contact their local code enforcement office and determine all of the regulations they are subject to. You must do this before installing the Vertical Platform Lift.

SITE REQUIREMENTS

• The lift will require a 115 VAC 20 AMP grounded circuit.

• Outdoor Installations will require a GFI protected circuit. (check with jurisdiction)

• Only install the lift on a 4" thick, level 3,500 PSI reinforced concrete slab.

• Foot Print varies depending on platform size and options. REQUIRED TOOLS

• Screwdrivers• 1/ 2" Hammer Drill

• 3/ 8" Masonry Drill Bit

• Appliance Dolly

• Hammer

• Level

• Measuring Tape

• Socket Wrench Set

• Voltmeter

REQUIRED MATERIALS

• 4 Floor anchors

AmeriGlide recommends securing the lift using our Anchor Kit. If you purchase you own floor anchors they must use 3/ 8" bolts and have a minimum tensile strength of 6000 lb.

Note:Lift must meet NFPA70 (National Electrical Code)

6 // 32 Hercules II 750 Vertical Platform Lift Manual | www.Ameriglide.com | 866-378-6648

P/N: 630-00046 RevD 111518

INSTALLATION PROCEDURES

PREPARING TO INSTALL THE LIFT

Final Site Inspection

Verify the surface the lift will mount to is smooth and level. This surface must be made from 3,500 PSI reinforced concrete with a minimum thickness of 4".

• The horizontal gap between the edge of the platform and the upper landing must no less than 3/ 8" and no greater than 3/ 4".

• The horizontal gap between the guard panel and any wall or barrier must be no less than 2" and no greater than 3".

• Verify that sufficient head room exists above the lift. The lift will require 6' 8" of clearance above the platform floor when the lift is at the upper landing.

Connecting to Electricity

The lift will require a 115 VAC 20 AMP grounded electrical circuit. Depending on local codes, this connection may need to be routed in electrical conduit and hard-wired.

Controller Harness Connections

CautionVerify that the running clearance around the lift complies with ASME A18.1 codes for your area.

Warning:Do not ride on the lift until it has been anchored in place.

Warning:The area between the floor where the lift is mounted and the top landing must be covered by a smooth vertical fascia. This is to eliminate any pinch points between the platform and

High VoltageCicuit Break

(AC unit only)

Low VoltageCircuit Breaker

PlatformTraveling Cable

Safety Pan Jumper

Upper Landing Interlock

Upper & Lower Limit Switch

Bypass Switches(strikes only)Upper & Lower

Call-SendsLower Landing

Interlock3-Stop only


P/N: 630-00046 RevD 111518


Step 5: Install two (2) joint fasteners and firmly tighten with 3/16" Allen wrench. Then slide rack pieces down to cover joint.Step 6: Turn over joined rails and install the remaining two (2) joint fasteners and firmly tighten with 3/16" Allen wrench. Then slide rack pieces down to cover joint.Step 7: Install rail brackets by loosening the screws and snapping each bracket edge into the slot, or

slide the brackets on from the top of the rail.

When in final position, the nuts will be on the wall side.Step 8: ________________________ A. For double rails, tighten the first rail bracket

in place so that, _________________________________________ when turned over, the back of the bracket touches the rear of the _______________________ first step from the bottom landing. Place and tighten the second _______________________ and third brackets on the steps on each side of the rail joint, again _______________________ so the back of the bracket touches the rear of the step. Then _____ place the fourth and final bracket on

the last step before the top ________________ ______________________________________landing, again tightening it so it touches the front of the rear of the last step. ______________________________________B. For single rails, tighten the first rail bracket in place so that, ___________________

INSTALLING THE PLATFORM

Step 1: The mounting bolts, nuts and spacers that secure the platform to the lift carriage are packaged in the small parts box. Begin by locating these pieces and setting aside.

Step 2: Position the platform by aligning the support legs with the carriage flanges that protrude from the front cover.

Step 3: Align the four mounting holes with those on the carriage. Insert 1/ 2 x 3" hex head bolts into each of the (4) holes. Install the low profile nuts on the upper bolts and the standard ones on the lower bolts.

Step 4: Plug in the harness for the platform safety pan and unplug the safety pan jumper on the controller (ref pg 5). Secure the harnesses under the clip on top of the carriage flange.


P/N: 630-00046 RevD 111518


INSTALLING THE PLATFORM GUARD PANELS

Step 1: Insert the guard panel posts in the pockets in the platform. The smooth side of the guard panel faces toward the center of the platform. Bolt each post in place with (2) 5/ 16 -18 x 2" and (1) 1/ 4 -20 x 2" hex head bolts.If you have a 90° exit platform, install the end guard panel using the provided bracket and bolt to inner guard panel.

Step 2: Install the platform control box on the rear guard panel using screws and nuts through the panel.

Step 3: Plug in the harness for the platform control box. Secure the harnesses under the clip on top of the carriage flange.

INSTALLING FIXED RAMP • Position the ramp after the lift is in its

final location.• Maintain a gap of 3/ 8" to 3/ 4" between

the ramp and platform.• Drill a pilot hole into the concrete and

fasten using supplied concrete lags through ramp flanges.


P/N: 630-00046 RevD 111518

Step 4: Attach the ramp roller arm by bolting it to the underside of the ramp.

The ramp roller should align and make contact with the ramp roller guide.

Step 1: Install the ramp roller guide on the side of the lift tower using the screws already installed in the panels.

Step 2: Attach the two ramp pivot tabs to the lower landing sides of the platform. Reinsert the hex bolts, one of which will go through the guard panel post, and tighten.

Step 3: Attach the ramp to the pivot tabs using shoulder bolts and locking nuts. Tighten the nuts until they seat against the bolt shoulder.

INSTALLING AUTO-FOLDING RAMP (OPTIONAL)

Rave Stair Lift Manual | www.Ameriglide.com | 866-378-6648



P/N: 630-00046 RevD 111518

ANCHORING THE LIFT

AnchorsAmeriGlide recommends securing the lift using the concrete anchors provided. If you purchase you own floor anchors they must be 3/ 8" minimum of sufficient length. All four floor anchors must be installed correctly in accordance to their instructions. Step 1:

• Position the lift in its final location.

• Verify that it is level and perpendicular to its surroundings and all running clearances are the proper dimension.

• Shim if necessary.Step 2: Use the lift’s base as a template. Drill 4 holes into the concrete making sure that the holes are deep enough to accept the anchors. Step 3: Secure the lift in place by tightening the floor anchor bolts.

Step 4: (800 or taller models)Taller lifts must have the top of the lift tower anchored into a solid surface to ensure running clearances remain constant.There are two options for anchoring the top of the tower: 1. For lifts going up to a landing such as a

deck or porch, the optional tower brace is the preferred method. Hardware is packed with tower brace.

2. For lifts that are placed with the back of the tower against a solid wall such as inside of a hoistway, drilling two holes through the top tower cross brace and anchoring is preferred.

TipConcrete dust may have settled into the holes you just drilled. Use a shop vacuum to clean out these holes. This will ensure the floor anchors set correctly.

Anchor two locations


P/N: 630-00046 RevD 111518

SETTING LIMIT SWITCHES

SETTING THE LIMIT SWITCHES

Your lift is equipped with upper and lower limit switches. The vertical location of these switches may be adjusted to fit your application. Typically the upper limit switch will need to be adjusted so the platform will stop level with the upper landing. The lower limit will typically not need adjusting.

Step 1: Verify the emergency switch is in the ON position. Run the lift in the up direction until the platform floor is level with the upper landing. Disconnect the lift’s power (at the building’s circuit breaker for AC units, at the battery box for DC units) before going to the next step.

Step 2: Remove the screws at the top of the lift that attach the front cover.

Step 3: Remove the front cover by tilting it forward and lifting upwards. The bottom of the front cover sits on a pin on either side of the lift frame. Set the cover aside in a safe location where it will not get damaged.

WarningMoving components can cut and crush. Do not operate the lift if you are in close proximity to any drive components. Be aware that loose clothing or jewelry may catch on moving parts.

Step 4: Loosen the bolts that attaches the upper limit switch assembly. Slide the assembly down the track until the lower switch in the assembly comes in contact with the lift’s car. You should hear the limit switch click as contact is made. Retighten the set screw fastening the limit switch assembly in place.

Step 5: Replace the front cover and secure it with the screws from step 2.Step 6: Re-connect the lifts electricial power at the circuit breaker. Verify that the emergency switch is in the on position.Step 7: Run the lift in the down direction for several inches. Next, run the lift in the up direction. Continue to press the up button until the upper limit switch has caused the lift to stop. Verify that the platform has stopped level with the upper landing. If it has not, readjust the limit until it is level.


P/N: 630-00046 RevD 111518

VERIFYING OPERATION OF LIFT

VERIFYING OPERATION OF THE LIFT

Step 1: Run the lift up and down for 5 complete cycles. Hold the direction button down and allow the limit switches to stop the lift. At the top, verify that the platform stops level with the upper landing. At the bottom, verify the access ramp (if equipped) unfolds and rests on the ground. Step 2: Verify the operation of the Emergency stop switch. When this switch is pushed in the lift should not run in either direction. When this switch is turned and pulled back out, the lift should operate normally.

Step 3: Verify the operation of the sensor pan underneath the platform. Start with the lift at the top landing. Press up on the sensor pan. While holding the pan in this location, press the down switch on the platform. The lift should not run.

CautionComplete the following section before training the customer to use the lift.

WarningDo not run the lift if anyone is under the platform.


P/N: 630-00046 RevD 111518

MANUAL OVERRIDE

Your lift is equipped with a manual handcrank, to be used in the case of a power failure.Before using the manual handcrank verify that it’s use is required. Check that the emergency stop switch is pulled out. Check that the electrical cord is connected to the supply. Also check that the buildings circuit breaker has not tripped. Try to run the lift by pushing both the up and down buttons. If the lift still will not run, complete the following steps:

Step 1: Disconnect the power from the lift.

Step 2: Remove the screws and remove the top cap at the top of the tower.

Step 3: Insert the manual handcrank into the opening on the top of the brake assembly. It may be neccesary to slightly rotate the handcrank until it fully seats down on the hex portion of the brake. Rotate the crank to raise or lower the platform.

CALL-SENDS (OPTIONAL)

The optional Call-Send controls are to be used at the upper and/or lower landings to call the platform to you or send it to the other landing.

They should be mounted on the wall at each landing. ASME A18.1 code is 15" to 48" from floor.

A length of multi‐conductor wire will need to be ran from the bottom of the lift tower up to the landing Call‐Sends. Consult local codes for type and mounting requirements. After wiring is completed, the wiring harness must be plugged into it appropriate receptacle on the controller (ref pg 6).

Wiring Connections

Call-Send Lift HarnessBlue Blue

White WhiteRed Red

WarningDo not service or operate the manual handcrank while the lift is connected to electricity.

WarningNever operate the lift while the manual override crank is inserted into the lift.


P/N: 630-00046 RevD 111518

TOP LANDING GATE (OPTIONAL)

The optional top landing gate is provided with a combination mechanical lock and electric contact (interlock).

The interlock:

• Prevents the lift from running if the gate is not closed.

• Prevents the gate from being opened if the platform is not at the top landing.

• Unlocks when the lift is on the upper limit switch.

A crescent shaped key is provided to manually unlock the gate during installation. The key is inserted from the back side to lift up on the solenoid that holds the gated locked. Mount the gate by placing onto the upper landing making sure to align the gate opening with the platform (outer guard rail not shown for clearity). There are a number of attachment holes provided in the threshold portion of the gate for mounting using wood lag screws or concrete anchors as appropriate. Remove the latch post cover and connect the call-send and interlock wire harnesses.

The vertical posts of the gate must be attached to a supporting structure, (the gate is not designed to be freestanding).A length of multi‐conductor wire will need to be ran from the bottom of the lift tower up to the landing gate. Consult local codes for type and mounting requirements. After wiring is completed, the wiring harness must be plugged into it appropriate receptacle on the controller (ref pg 6).

Wiring ConnectionsInterlock_Harness Lift Harness

Black BlackBlack GreenYellow WhiteYellow Orange

* Blue* Brown

* Must be tied together

Call/Send Harness Lift HarnessBlue Blue

Yellow WhiteRed Red


P/N: 630-00046 RevD 111518

EMI AND FLUSH STRIKE INTERLOCKS (OPTIONAL)

For Optional DC powered liftsFolger/Adams Strike Wires Lift Harness Wires

Black BlackPurple GreenWhite White

Orange OrangeYellow BlueBrown Brown

NOTE: Blue and Green from strike not used.

EMI Interlock1. Position interlock to

door jamb and mark mounting holes.

2. Fasten Interlock to door jamb with #8 wood screws.

3. Route 4-conductor Interlock cable thru hole in top of interlock and make wire connections.

4. Attach door keeper and emergency key plates to hoistway door.

EMI Interlock Wiring Connections

EMI Lift Harness WiresBlack (A) BlackBlack (B) GreenYellow (C) WhiteYellow (D) Orange

— Blue*— Brown*— Red

* Must be tied together when using an EMI Interlock.

The optional EMI or Flush Strike Interlocks are provided with a combination mechanical lock and electric contact. They are to be used with existing doors.

The interlock: • Prevents the lift from running if the gate

is not closed.• Prevents the door from being opened if

the platform is not at the landing.

A length of multi-conductor wire will need to be ran from the bottom of the lift tower to each interlock. Consult local codes for type and mounting requirements. After wiring is completed, the wiring harness must be plugged into it appropriate receptacle on the controller (ref pg 6).

Flush Strike InterlockRefer to the instructions inside the strike box for mounting requirements.

Flush Strike Interlock Wiring Connections

For AC powered liftsFolger/Adams Strike Wires Rectifier Wires Lift Harness Wires

Purple Red —

Purple Black —

— Yellow Black

— Yellow Green

White — White

Orange — Orange

Yellow — Blue

Brown — Brown

NOTE: Blue and Green from strike not used.

Hercules II 750 Vertical Platform Lift Manual | www.Ameriglide.com | 866-378-6648


P/N: 630-00046 RevD 111518

PLATFORM GATE

PLATFORM GATE (OPTIONAL)

The optional platform gate is provided with a combination mechanical lock and electric contact (interlock). The interlock:

• Prevents the lift from running if the gate is not closed.• Prevents the gate from being opened if the platform is not at the bottom landing.• Unlocks when the lift is on the lower limit switch.

A crescent shaped key is provided to manually unlock the gate during installation. The key is inserted from the back side to lift up on the solenoid that holds the gated locked. Mount the gate by placing onto the lower landing side of the platform. There are a number of attachment holes along the bottom and up the sides of the gate frame to attach to the platform and guard panels.

A wiring harness included on the gate will need to be routed along the gate frame, behind the rear guard panel and connected to its adjoining harness plug on the lift carriage. After wiring connection is made, the wiring harness must be plugged into its appropriate receptacle on the contoller (ref pg 6).


P/N: 630-00046 RevD 111518

FASCIA PANEL

FASCIA PANEL (OPTIONAL)

A fascia panel provides a smooth surface for the platform edge to run against to prevent any shear or obstruction hazards and must be utilized.A running clearance of no more than 3/ 4" and no less than 3/ 8" must be maintained between the edge of the platform and the fascia panel.

PLATFORM CONTROL WITH OPTIONAL E-STOP ALARM

If equipped, the e-stop button on the platform lights up and sounds an alarm when pressed. You will need to obtain a 6 VOLT lantern battery like the example below.

The battery can sit under the top cap to the right of the motor pulley. There is a wire harness for the battery located here. Wire #1 connects to the positive terminal and wire #2 to the negative terminal.


P/N: 630-00046 RevD 111518

COMMERCIAL PLATFORM LIFTOWNERS SECTION

READ THE MANUAL THOROUGHLY BEFORE OPERATING THE LIFT.


P/N: 630-00046 RevD 111518

Congratulations on the purchase of your AmeriGlide Vertical Platform Lift. This lift has been engineered to provide trouble free service for many, many years. Please read this manual completely before operating your lift.

SAFETY

• Do not exceed the maximum payload capacity of 750 lb

• Do not ride on the lift until it is anchored in place.

• This product is designed only for lifting people and wheel chairs. Do not use it for any other purpose.

• Make sure any obstructions are cleared from underneath the platform area before use.

• Make sure both the passenger and wheelchair are completely on to the platform before using.

• Do not disable any safety equipment or switches supplied with this lift.

• Do not attempt to service the lift yourself. Contact your AmeriGlide dealer for assistance.

• Do not allow children to operate or play around the lift.

• Read all instructions in this manual before installing or operation the lift.


P/N: 630-00046 RevD 111518

CONTROLS

Emergency Stop

In an emergency push this red button to stop the lift. Turn the button clockwise to run.

Up

Controls upward movement of lift platform. To move platform up, depress and hold the upper half of the rocker switch. To cease movement, release switch.

Down

Controls downward movement of lift platform. To move platform down, depress and hold the lower half of the rocker switch. To cease movement, release switch.

Keylock (optional)

Disables controls from operating when keylock is turned off.

21 // 32

GLOSSARY

Hercules II 750 Vertical Platform Lift Manual | www.Ameriglide.com | 866-378-6648

P/N: 630-00046 RevD 111518

OPERATING THE LIFT

Step 1 - Up: Drive onto and stop in the middle of the platform. Apply the brakes of your chair or scooter.

Step 2: Verify that the emergency stop button is not activated by giving it a quick pull on the stop button.

Step 3: Press and hold the UP rocker. The lift will move in the up direction and stop when it reaches the upper landing.

Step 4: Release the brakes on your chair or scooter and drive off the platform.

WarningAlways verify the lift’s platform has stopped level with the upper landing. If not contact your AmeriGlide Dealer for assistance.


P/N: 630-00046 RevD 111518

Step 1 - Down: Drive onto and stop in the middle of the platform. Apply the brakes of your chair or scooter.

Step 2: Verify that the emergency stop button is not activated by giving it a quick pull on the stop button.

Step 3: Press and hold the DOWN rocker. The lift will move in the down direction and stop when it reaches the lower landing.

Step 4: Release the brakes on your chair or scooter and drive off the platform.

WarningAlways verify the lift’s platform has stopped level with the upper landing. If not contact your AmeriGlide Dealer for assistance.


P/N: 630-00046 RevD 111518

90 V

DC

Mot

orU

pTo

p Lm

t

UP

A1

A2

Dow

n

DN

A1

A2

VA

CV

AC

24

Top

Inte

rlock

Sol

enoi

d

Fina

l Lm

tCN

C

110

Key

Sw

itch

SA

FA

1A

2

Em

erge

ncy

Sto

pS

AF 2

1

Saf

ety

Pan

Sw

itche

s

CN

CC

NC

CN

CC

NC

110 VAC

2

3

8

4

10

11

1

12

13

DN

2221

UP

2221

15 A

mp

C.B

.3

Am

pC

.B.

Top

Gat

eC

lose

d

6

7

CN

O

Btm

Gat

eC

lose

d

CN

O

CN

C Btm

Lm

t

Btm

Inte

rlock

Sol

enoi

d9

Btm

Doo

rLo

cked

Byp

ass

Top

Doo

rLo

cked

Byp

ass

5

+ -6V

DC

UP 3

4

RED

BLK

Bel

t Mon

itor

CN

O

CN

C

NO

NO

14 15 16

L1L2

G

4Te

rmin

al S

trip

Con

nect

ion

Sw

itch

- N.C

.

Sw

itch

- N.O

. hel

d cl

osed

Pus

h B

utto

n

Con

tact

- N

.O.

Con

tact

- N

.C.

Circ

uit B

reak

er

Lege

nd:

Opt

iona

l Equ

ipm

ent

Cal

l Sen

d

NO

NO

NO

NO

C C

C C

UP 2

1

DN 1

2

-15VSig+15V

L2 L1

90V

DC

Out

put

12A

Reg

en D

rive

TachComEN

DN 3

4

+ -~

~

17 6 1213

Opt

iona

l Wire

less

Cal

l-Sen

ds

98

NO

CO

M

A1

A2

NO

C

NO

C

NO

CO

M

A1

A2

Opt

iona

l Aut

o D

oor

Ope

ner R

elay

s

Top

Btm

Land

ing

Sw

itch

Land

ing

Sw

itch

To D

oor

Ope

ner

To D

oor

Ope

ner

12 13

CN

CC

NC

Pit

Sw

itchC

NC (O

ptio

nal)

Opt

. Flo

wS

witc

h

1

BB

AA

44

33

22

11

4423

1 RE

V F

SCH

EMAT

IC, C

PL A

C, 2

-STO

P


P/N: 630-00046 RevD 111518

VA

CV

AC

2411

0

15 A

mp

C.B

.

3 A

mp

C.B

.

90 V

DC

Mot

or

BR

AK

E

Cal

l Sen

d

NC

NCNO

NC

Em

erge

ncy

Sto

p

Pla

tform

Con

trol

CN

CC

NC

CN

CC

NC

Saf

ety

Pan

LowerLimit

UpperLimit

FinalLimit

Trav

el C

able

#44

042

/ 43

/ 44

Saf

ety

Nut

HR

NS

#44

011

Cal

l Sen

d #4

9300

NO

C

NO

SO

L

Gat

eC

lose

d

C

NO

SO

L

Gat

eC

lose

d

Opt

iona

lP

hone

Jack

Opt

iona

lP

latfo

rmG

ate

Opt

iona

lTo

p La

ndin

gG

ate

Opt

iona

lLi

ghte

dA

larm

Cal

l Sen

d

NC NO

NC

LowerBypass

UpperBypass

NO

Opt

iona

l Top

or B

otto

mE

lect

ric D

oor S

trike

Opt

iona

l Top

or B

otto

mE

lect

ric D

oor S

trike

1 2 3 4 6 7 8 95 1 2 1 2 3 4 65 1 2 3 4 65 1 2 3 4 6 7 8 95

1 2 3 4 65

1 2 3 1 2 3 1 2 3 4

1 2

12 3 46 5 1 2 3 1 2

-15V

Sig

+15V

L2

L1

90VDC Output

12A

Regen Drive

Tach

ComEN

NO

Bel

tM

onito

r

C

NC

SO

L

Doo

rC

lose

d

Doo

rLo

cked

C

NC

Pow

erM

odul

e1

AC AC

DC

+

DC

-

AC AC

DC

-

DC

+

1 1

Ele

ctric

Stri

ke P

ower

Opt

. Flo

atS

witc

h

BB

AA

44

33

22

11

4423

1 RE

V F

WIR

ING

DIA

GRA

M, C

PL A

C, 2

-STO

P


P/N: 630-00046 RevD 111518

90

VD

CM

oto

r

Up

To

p L

mt

UP

A1

A2

Do

wn

DN

A1

A2

VA

CV

AC

24

Top I

nte

rlock

Sole

noid

Fin

al L

mt

CN

C

11

0

Ke

yS

witch

SA

FA

1A

2

Em

erg

en

cyS

top

SA

F 21

Sa

fety

Pa

n S

witch

es

CN

CC

NC

CN

C

CN

C

110 VAC

2

3

8

4

10

11

1

12

13

DN

22

21 U

P

22

21

15

Am

pC

.B.

3 A

mp

C.B

.

To

pG

ate

Clo

sed

6

7

CN

O

Btm

Ga

teC

lose

d

CN

O

CN

C Btm

Lm

t

Btm

Inte

rlock

Sole

noid

9

Btm

Do

or

Lo

cke

d

Byp

ass

- 3

, 4

To

p D

oo

rL

ocke

d

Byp

ass

- 1

, 2

5

+ -6V

DC

UP

34

RED

BLK

Be

lt M

on

itor

CN

O

CN

C

NO

NO

L1

L2

G

4T

erm

inal S

trip

Connection

Sw

itch -

N.C

.

Sw

itch -

N.O

. held

clo

sed

Pu

sh B

utton

Conta

ct -

N.O

.

Conta

ct -

N.C

.

Cir

cuit

Bre

aker

Legend:

Op

tion

al E

quip

ment

NO

NO

NO

NOC C

C C

UP

21

DN

12

-15V

Sig+15V

L2

L1

90

VD

C O

utp

ut

12

A

Re

ge

n D

rive

TachComEN

DN

34

+

-~

~

Mid

14

Mid

Inte

rlock

15

Byp

ass

NO

C

Mid

Ga

teC

lose

d

CN

O

164 3 2 1

8 7 6 5

Mid

Lm

t

CN

CC

NC

CN

C

Pit S

witch

(Op

tio

na

l)

Op

t. F

loa

tS

witch

BB

AA

44

33

22

11

SCALE

~±

1±

0.0

10

± 0

.02

± 0

.1

FRO

M D

RAW

ING

.-

DO

NO

T M

EASU

RE

AN

GLE

S

-

.X

XX

.X

XD

ECIM

ALS

.X

TO

LERAN

CES A

RE:

DIM

EN

SIO

NS A

RE I

N I

NCH

ES.

UN

LESS O

TH

ERW

ISE S

PECIF

IED

PER

ASM

E Y

14.5

- 2

009

INTER

PR

ET D

RAW

ING

AN

D T

OL

WIT

HO

UT W

RIT

TEN

CO

NSEN

TN

OT T

O B

E C

OPIE

D O

R U

SED

CO

NFID

EN

TIA

L IN

FO

RM

ATIO

N

REV E

2 O

F1

SH

EET

BSIZ

E

5/1

0/2

010

DF

DATE

DRAW

N B

Y

DESCRIP

TIO

N

44331

DW

G N

O.

SCH

EM

ATIC

, CPL A

C, 3-S

TO

P

20-A

pr-

15

MN

REF E

CO

-001149

AD

DED

OPTIO

NAL F

LOAT S

WIT

CH

;

E29/M

AR/1

8BK

INFO

RM

ATIO

N. R

EF E

CO

-003048

CO

RRECTIO

NS A

ND

AD

D C

ON

NECTO

R

D

DATE

CH

KBY

DESCRIP

TIO

NR

EV

REVIS

ION

HIS

TO

RY

1 2 3

TO

P C

ALL

MID

CALL

BO

TTO

M C

ALL

Ca

ll S

tatio

n

1 2 3

Ca

ll S

tatio

n

13

1 2 3

Ca

ll S

tatio

nT

BD

LS

-2T

RA

VE

L-4

,L

S-1

Mid

Inte

rlock

A1

A2

Inte

rlo

ckS

ole

no

id

WH

ITE

Do

or

Lo

cke

d

Do

or

Clo

sed

DN

51

52

UP

51

52M

id I

nte

rlo

ck

- 2

Mid

In

terlo

ck -

1

To

UP

- 5

2

Byp

ass

NO

C

Top

Inte

rlock

A1

A2

Inte

rlo

ckS

ole

no

id

WH

ITE

Do

or

Lo

cke

d

Do

or

Clo

sed

1 2 3 41223 5

4

8 7 35

Byp

ass

NO

C

Btm

Inte

rlock

A1

A2

Inte

rlo

ckS

ole

no

id

WH

ITE

Do

or

Lo

cked

Do

or

Clo

sed

8 7 212

BYPASS S

EE T

OP A

ND

BTM

INTERLO

CKS

Fie

ld W

irin

g

1 2 3 4 65

Tra

velin

gC

ab

le

12 6 713

7 98

5 14

15

16

LS-1

Bla

ck

Wh

ite

Gre

en

Blu

e

Re

d

Se

e In

terl

ock

Co

nn

ect

ors

7

To

Mid

Inte

rlo

ck -

4F

rom

Top

Inte

rlo

ck -

3

To

Btm

Inte

rlo

ck -

46

Fro

m M

idIn

terl

ock

- 3

SM

SCHM

ATIC

, CPL

AC

3-ST

OP44

331

REV

E


P/N: 630-00046 RevD 111518BB

AA

44

33

22

11

SCALE

~±

1±

0.0

10

± 0

.02

± 0

.1

FRO

M D

RAW

ING

.-

DO

NO

T M

EASU

RE

AN

GLE

S

-

.X

XX

.X

XD

ECIM

ALS

.X

TO

LERAN

CES A

RE:

DIM

EN

SIO

NS A

RE I

N I

NCH

ES.

UN

LESS O

TH

ERW

ISE S

PECIF

IED

PER

ASM

E Y

14.5

- 2

009

INTER

PR

ET D

RAW

ING

AN

D T

OL

WIT

HO

UT W

RIT

TEN

CO

NSEN

TN

OT T

O B

E C

OPIE

D O

R U

SED

CO

NFID

EN

TIA

L IN

FO

RM

ATIO

N

REV E

2 O

F2

SH

EET

BSIZ

E

5/1

0/2

010

DF

DATE

DRAW

N B

Y

DESCRIP

TIO

N

44331

DW

G N

O. SCH

EM

ATIC

DIA

GR

AM

, CPL

AC, 3-S

TO

PFIE

LD

IN

STALLED

EQ

UIP

MEN

T

98

1

NO

CO

M

A1

A2

NO

C

NO

C

NO

C

Mid

Call

Sta

tion

NO

CO

M

A1

A2

NO

CO

M

A1

A2

Do

or

Op

en

er

Re

lays To

p

BtmMid

La

nd

ing

Sw

itch

La

nd

ing

Sw

itch

La

nd

ing

Sw

itch

To

Do

or

Op

en

er

To

Do

or

Op

en

er

12

13

UP

62

61

DN

62

61

5

Mid

Inte

rlock

Inte

rlock

Sole

noid

ELE

CTRIC

STRIK

E W

IRIN

G46067, 46068 B

lack

Bla

ck

White

White

NO

C

NC

DO

OR O

PEN

ER

WIR

ING

Von D

uprin

Folg

er

Adam

s

Mid

Inte

rlock

Inte

rlock

Sole

noid

NO

C

NC

Bla

ck

Bla

ck /

White

White

Blu

eN

O

C

NC

Trine

Ora

nge

Bro

wn

Blu

e

Bla

ck /

White

Gre

en

Yello

w

Gre

y

Ora

nge

NC

Mid

Inte

rlock

Inte

rlock

Sole

noid

NO

C

NC

Bla

ck

Bla

ck /

White

White

NO

C

NC

Ora

nge

Bro

wn Blu

e

Bla

ck /

White

Bro

wn

Gre

y

Ora

nge

NC

White

Vio

let

NO

C

NC

Mid

Inte

rlock

Inte

rlock

Sole

noid

C

NC

Bla

ck

Door

Clo

sed

White

C

NC

Ora

nge

Bro

wn

Blu

e

SO

LE

NO

ID C

ON

TR

OL

NO

C

C

NC

EM

I In

terlock

Door

Lock

ed4621, 4622

A B C D

NC

Yello

w

SCHE

MAT

IC D

IAGR

AM, C

PL A

C3-

STOP

4433

1 RE

V E


P/N: 630-00046 RevD 111518

1 1

2 2

3 3

4 4

AA

BB

NC

C

C

CH

AR

GE

RBA

TTER

Y

MO

TOR

SPEE

D

NO

C

CC

ON

TRO

L

NO

CN

OC

NO

-C

NO

NC

12 V

DC

24 V

DC

NC

C

G

PWM

NC

+

+12V

+M

C

NC

C

NC

C

12 V

DC

NO

NC

CC

CN

CC

NC

NC

NC

NC

-

+

NO

CC

-M

Brak

e

Mot

or

15 16

REDBLK

24VD

C

Bel

t Mon

itor

Cal

l Sen

d

24VD

C

Up

Top

Lmt

Dow

n

Fina

l Lm

t

Key

Sw

itch

(OPT

ION

AL)

Emer

genc

yS

top

4

Key

Sw

itch

(OP

TIO

NAL

)

Term

inal

Stri

p C

onne

ctio

n

Safe

ty P

an S

witc

hes

2

3

8

4

10

11

1

Sw

itch

- N.C

.

Sw

itch

- N.O

. hel

d cl

osed

Push

But

ton

Con

tact

- N

.O.

Con

tact

- N

.C.

7

7 7

Circ

uit B

reak

er

Lege

nd:

30 A

mp

3 A

mp

Top

Gat

eC

lose

d

6

7

(Opt

iona

l)Pi

t Sw

itch

Btm

Gat

eC

lose

d

Btm

Lm

t

9

Btm

Doo

rLo

cked

Byp

ass

Braking Resistor

Top

Doo

rLo

cked

Byp

ass

5

+ -6V

DC

Opt

iona

l Equ

ipm

ent

14

12

13

34

8

68

3

4

DN

U2

UP

DN

UPDN

Top

Inte

rlock

Btm

Inte

rlock

A1

A2

Sole

noid

A1

A1

D2

A1

DN

A2

A2

U2

UP

SAF

SAF

Sole

noid

U2

D2

D2

A2

A1

6

UP

SCHE

MAT

IC, C

LP D

C2-

STOP

4414

1 RE

V F


P/N: 630-00046 RevD 111518

1 1

2 2

3 3

4 4

AA

BB

24 V

DC

Mot

or

50W-3Ω

Opt

iona

l Top

or B

otto

mE

lect

ric D

oor S

trike

BR

AKE

NC

NO

Belt

Mon

itor

Cal

l Sen

d

NC

NCNO

NC

Em

erge

ncy

Sto

p

Pla

tform

Con

trol

CN

CSa

fety

Pan

X6

LowerLimit

UpperLimit

FinalLimit

Trav

el C

able

#44

042

/ 43

/ 44

Plat

form

Con

trol

#49

218

Cal

l Sen

d #4

9300Gat

e C

all

Sen

d H

RN

S#4

4012

Limit Sw

itch HR

NS #44007

NO

C

NO

SO

L

Gat

eC

lose

d

C

NO

SO

L

Gat

eC

lose

d

Opt

iona

lP

hone

Jack

Opt

iona

lP

latfo

rmG

ate

Opt

iona

lTo

p La

ndin

gG

ate

Opt

iona

lLi

ghte

dA

larm

Cal

l Sen

d

NC NO

NC

LowerBypass

UpperBypass

NO

Opt

iona

l Top

or B

otto

mE

lect

ric D

oor S

trike

1 2 3 4 6 7 8 95 1 2 1 2 3 4 65 1 2 3 4 65 1 2 3 4 6 7 8 951 2 3 1 2 3 1 2 3 4

1 2

12 3 46 5 1 2 3 1 2

SO

L

Doo

rC

lose

d

Doo

rLo

cked

1 2 3 4 65

WIR

ING

DIAG

RAM

, CPL

DC

2-ST

OP44

141

REV

F


P/N: 630-00046 RevD 111518

1 1

2 2

3 3

4 4

AA

BB

Up

Top

Lmt

UP

A1A

2

Dow

nD

NA1

A2

Top

Inte

rlock

Sol

enoi

d

Fina

l Lm

t

NC

Key

Sw

itch

SAF

Em

erge

ncy

Stop

4Te

rmin

al S

trip

Con

nect

ion

Saf

ety

Pan

Sw

itche

sN

CN

CN

CN

C

2

3

8

4

10 11

1

12

13

Switc

h - N

.C.

Switc

h - N

.O. h

eld

clos

ed

Push

But

ton

Con

tact

- N

.O.

Con

tact

- N

.C.

Circ

uit B

reak

er

Legend

:

30 A

mp

Top

Gat

eC

lose

d

6

7

NO

Btm

Gat

eC

lose

dNO

NC B

tm L

mt

Btm

Inte

rlock

Sol

enoi

d9

Btm

Doo

rLo

cked

Bypa

ss

Top

Doo

rLo

cked B

ypas

s

5

+ -6V

DC

Bel

t Mon

itor

NO

Opt

iona

l Equ

ipm

ent

NC

NO

NO

14 15 16

U2

A1A

2 D2

A1A

2

SAF

D2

D2 + +

12 V

DC

BATT

ERY

CH

ARG

ER

24 V

DC

--

12 V

DC

24V

DC

BR

AK

E

NO

NO

NO

NO

Mid

4 3 2 1

8 7 6 5M

id L

mt

Mid

Inte

rlock

Sol

enoi

d

Cal

l Sta

tion

Up

Mid

Dow

n1312

6 6 6

Mid

Gat

eC

lose

dNO

24VD

CM

otor

3 A

mp

DN

UP

DN

UP

RED

DN

UP

BLK

7

7 7 7A1

NC

Pit

Sw

itch

NC

NC

A2

Mid

Doo

rLo

cked

Byp

ass

NO

NO

1312

1

NO

CO

M

A1A2

NO

C

NO

C

NO

CM

id C

all

Sta

tion

NO

CO

M

A1A2

NO

CO

M

A1

A2

Doo

r Ope

ner

Rel

ays

Top

Btm

Mid

Land

ing

Switc

h

Land

ing

Switc

h

Land

ing

Switc

h

To D

oor

Ope

ner

To D

oor

Ope

ner

To D

oor

Ope

ner

8 9

4

3

86

U2

U2

4

3

86

WIR

ING

SCHE

MAT

IC, C

PL D

C3-

STOP

640-

0000

5 RE

V A


P/N: 630-00046 RevD 111518

• Parts used that are not approved by AmeriGlide • Labor fees for installation work, repair or service calls are not covered• Outdoor installation within 1 mile of a coastline reduces warranty

to 180 days and expressly excludes rust after 30 days. Warranty is extended to 2 years with Premium Protection Option.

• Due to the nature of steel construction being permanently placed in an outdoor environment and its inherent unpredictability, minor paint defects and cosmetic rust are not covered after 30 days by AmeriGlide’s Limited Warranty.

• AmeriGlide enclosures, when used, are designed to protect a CPL and its users from being directly affected by the elements.It is NOT intended nor designed to be completely water proof.

Effective August 1, 2017 TEC 2006 P/N: CSVF-000016 Rev B

Phone: Email:

Hercules II CPL– TWO YEAR WARRANTY CERTIFICATE

LIMITED WARRANTY CERTIFICATEProducts Covered: HERCULES II

PLEASE FILL OUT ALL FIELDS AND RETURN WITHIN TEN (10) DAYS OF PRODUCT INSTALLATION. Mail to AmeriGlide, 2075 47th Street, Sarasota, FL 34234. AmeriGlide warrants to the original purchaser of a Hercules Commercial Vertical Platform Lift (CPL) manufactured by us to be free from defects in material, mechanical and electrical components (parts) for a period of two (2) years, provided that the products have been installed, maintained and operated properly according to the AmeriGlide Installation and Owner’s Manuals.

EXCEPTIONS TO THIS LIMITED WARRANTY ARE: PLEASE READ CAREFULLY

• AmeriGlide CPL’s and EPL’s installed outdoors must include the Premium Protection Package to maintain 2-year warranty; otherwise warranty is limited to one (1) year.

• Batteries are limited to one (1) year with a AmeriGlide supplied/approved charger.

• Damage resulting from improper installation or operation• Additional parts/labor related to code compliance that were not

identified on the original order• Negligence, alterations, abuse or misuse of the equipment • Fire, flood, acts of God • Shipping damage

This warranty starts on the date of initial product installation (not to exceed 90 days from the date of manufacture), provided the warranty certificate is completely filled out and returned to AmeriGlide within ten (10) days of installation. AmeriGlide and its dealers shall not be liable for any consequential, special or incidental damages arising out of the purchase or use of the unit or resulting from the breach of this Limited Warranty, or any implied warranty. The limit of liability of AmeriGlide and its dealer hereunder shall be the unit’s purchase price. Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, or legal remedies, so these above limitations may not apply to you. All warranty claims must be reported to the dealer from whom the lift was purchased as they have responsibility for handling your warranty claim. The dealer is to contact the Technical Services Department of AmeriGlide and provide the serial number of the product along with a description and evidence of the defect(s) supporting a warranty claim. Dealers may charge for labor, service, travel, or other associated costs to make repairs, and such charges are not covered by this Limited Warranty. It is permissible to have any repairs or replacement work done as a result of any defects in material and workmanship by someone other than the Dealer under this Limited Warranty. However, the Limited Warranty does not cover any charges or expenses assessed by any such other person or company performing such repairs or replacement work. All parts used to replace defective materials must be genuine AmeriGlide parts to be covered by this Limited Warranty. This Limited Warranty gives you specific legal rights, and you may have other rights which vary from state to state. AmeriGlide will not be charged for labor, consequential damage or repair expenses. AmeriGlide will not, under any circumstances, be liable for the loss of the use of its products or loss of time. Defective parts must be returned, if requested, prepaid, to AmeriGlide for inspection prior to credit or replacement. At AmeriGlide’s discretion, any part found to have been modified, over-stressed, damaged by accident, or misused is not covered by this warranty. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OR CONDITIONS, INCLUDING ALL IMPLIED WARRANTIES OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND THERE ARE NO WARRANTIES THAT EXTEND BEYOND THE DESCRIPTION OF THE LIMITED WARRANTY DESCRIBED HEREIN.

PRODUCT INFORMATION: PURCHASER INFORMATION:Model: Name: Premium Protection Package: Yes No Mailing Address:Serial Number: Installation Address (if different):Date of Installation: Type of Installation: Indoor Outdoor

Residential CommercialDEALER/INSTALLER INFORMATION ADDITIONAL INFORMATION:Company Name: How did you hear about AmeriGlide?Installer Name: Dealer Internet Magazine Friend/Family OtherAddress:

Phone: Style Dealer Own Other AmeriGlide Product Ease UseE-Mail: Recommendation Price/Value Key Feature

I selected AmeriGlide due to its (select all that apply):


P/N: 630-00046 RevD 111518

NOTES:

P/N: 630-00046 RevD 111518

installation & owners manual hercules ii 750...hercules ii 750 vertical platform lift manual...

Documents