installation instructions forinstallation 3 3 4 4 1 figure b note: use only two vandal resistant...

POWDER COATED AND STAINLESS STEEL PARTITIONS

INSTALLATION INSTRUCTIONS FOR

2171 Liberty Hill Rd.,Eastanollee, GA 30538 Phone:(706)827-2700 Fax:(706)827-2710Website: www.globalpartitions.com Email: [email protected]

While all materials and standard mounting selections are present, in order tocover the numerous choices of hardware, we have presented each material

with it's default hardware. Therefore, while each type is covered, it will be withit's most common mounting style (i.e. continuous brackets on ceiling-hung,

piano hinges on Polymer)

This installation guide was designed to cover as many variations of hardwareand mounting styles possible, while also trying to keep it light and focused.

Please read all steps in their entirety before beginning actual install, as somefield conditions and hardware combinations may require alternate installation.

Thank you for choosing Global Partitions

Ceiling Anchored Page

22

19Panel To Pilaster/Wall Two Ear Assembly.................

Pilaster/Panel Alcove Assembly................................

Panel To Pilaster/Wall One Ear Assembly.................

Pilaster/Wall One Ear Assembly................................ 21

20

Step 4,5,6...................................................................

Step 1,2,3...................................................................

18

17

5Pilaster/Wall One Ear Assembly................................



Pilaster/Wall One Ear Assembly................................ 15

16

14

Panel To Pilaster/Wall Two Ear Assembly.................

Step 4,5,6....................................................................

Step 1,2,3...................................................................

12

13

11

8A-8BDoor Hardware Assembly (Typical All Styles) ...

Floor AnchoredUrinal Screen Assembly.............................................

Headrail Assembly.....................................................

Page10

9

Pilaster/Panel Inline Assembly..................................


7

6

2Step 4,5,6....................................................................



4

3

Floor Anchored/Overhead BracedStep 1,2,3...................................................................

Page1

Table Of Contents


Powder coated metal / Stainless steel

The Components for this project have been custom fabricated. They areguaranteed with respect to manufacture and workmanship and were inspected

at the factory.Before beginning work, the units should be inspected. If damage occurred intransit, report immediately to the freight company or other agencies that may

have caused the damage.

25Panel To Pilaster/Wall Two Ear Assembly.................

Product Information

Urinal Screen Assembly.............................................

Pilaster/Wall One Ear Assembly................................


Care And Maintenance Of Toilet Partitions................

Page

34

32

33

31


Full Height Bracket Kits

Pilaster/Panel Inline Assembly..................................



Pilaster/Wall One Ear Assembly................................

28

Page

30

29

27

26

Floor Anchored And Ceiling AnchoredStep 1,2,3...................................................................

Step 4,5,6....................................................................

Page

24

23

Table Of Contents


FIGURE 1

17"

Page 1

STEP 3POSITION PANEL

PILASTERCENTER LINE

FIGURE 3

48"

WALL PILASTERCENTER LINE

FLOORFASTENERLOCATIONS

STEP 2WALL BRACKETS AND FLOOR BRACKETS

17"17"

PANELCENTER LINE

FIGURE 2

48"48"

17"

48"

STEP 1LAYOUT

12" SUPPORT

LC

LCLC

LC LCLC


A. Review the layout drawings and package lists that have accompanied this job.

B. Before proceeding,confirm that backing of walls and floor is adequate to support secure mounting of the toilet compartment units.

C. Establish and mark pilaster center line from back wall.

D. Establish and mark panel center lines for wall brackets.

E. Establish pilaster floor fastener locations from side wall according to shop drawings. (Note floor fasteners are located roughly 1" from lockstrip edge of pilaster. Larger overhead-braced

pilasters will have multiple stems. Use only the 2 outside stems for floor attachment. Conversely, 3" and 4" pilasters will use only

F. Mark wall bracket holes using the brackets as templates.

A. Using shop drawings, drill holes for wall brackets and floor fastenings for particular fastening devices supplied.

B. Insert anchoring devices in walls and secure wall brackets.

C. Insert expansion shields. Position shoe clips and then "L" brackets over expansion shields and secure loosely with screws.

A. Place panel on a support, 12" above the floor.

B. Set it into wall brackets,but do not fasten panel at this time.

Detail of pilaster mounting can be found in Step 5.

(Securingly loosely at this time will allow for lateral pilaster adjustment.)

one " L" clip on one of the two stems.

Typically 1/4" drill bits can be used throughout. An assortment of bit sizes are recommended as site conditions vary.

FLOOR ANCHORED- OVERHEAD BRACEDPOWDER COATED / STAINLESS STEEL

FIGURE 4

A. Plumb each pilaster and fasten the pilaster to panel using "U" brackets and sheet metal screws.

B. Establish door openings by setting pilaster mounting.

C. Tighten self tapping screw to "L" brackets.

D. Slide stainless steel shoe down to floor level, firmly engaging shoe clips.

F.Remove panel support device.

Page 2

STEP 5INSTALL PILASTERS

STEP 4PILASTER PREPARATION

FIGURE 5

REAR

FRONT

STEP 6SECURING PILASTERS/PANELS

FIGURE 6


A. Refer to layout drawings for placement of U-brackets in position on rear of pilasters. Make sure

brackets are in alignment with wall brackets.

B. Fasten U-brackets to pilaster with sheet metal screws.

NOTE: Pilasters at wall do not require U-brackets,but should be prepared for wall (and floor fastening) as required by compartment layout.

A. Inspect stainless steel shoe carefully for bowing. If shoe seems wide, squeeze edges and center to ensure

shoe will not bow away from pilaster faces.

B. Place pilaster between "L" brackets and fasten loosely with screws at pre-drilled locations at each side.

( 3" and 4" pilasters will have only 1 "L" clip.)Adjust threaded Jack bolt until it reaches floor.

Slide stainless steel shoe carefully over mounting end of pilaster and leave approximately 5" above bottom end of pilaster.

Shoe can be held in place with painters tape to avoid sliding.



DIMENSIONTO SUITINSTALLATION

5"(APPROX.)

Fasten pilaster to panel using sheetmetal screws(Refer to steps 4 & 6 )

Pre-drill for screws with 1/8" bit.

Pilasters must be both plumb and level. To assist inleveling, headrail may be lightly positioned acrossadjacent pilasters(do not fasten at this time)

Remove support device.

FLOOR ANCHORED/OVERHEAD BRACEDPANEL TO PILASTER/WALLTWO EAR ASSEMBLY

4 1

5"(APPROX.)

33

FIGURE A

4


33

44 1

FIGURE B

NOTE:Use Only Two Vandal Resistant 5/8" SMSTo Diagonally Fasten U-bracketTo Pilaster.

FIGURE B

Page 3

5

5

5"(APPROX.)2

2


5

55

Plastic Shields

4


2

FIGURE A

53

5 3

55"(APPROX.) 1

4

Vandal Resistant 5/8" S.M.S (12)

(4)

Vandal Resistant 2 1/2" S.M.S

5

4

(4)

"U" Bracket2

3

1 Two Ear Bracket

(2)

(2)

Panel Hardware Kit (P/N 40-8515020G) Includes:CHROME PLATED ZAMAC

PART ID. DESCRIPTION QTY

5

5

5

5

5

5

5

5

Panel Hardware Kit (P/N 40-8265021G) Includes:STAINLESS STEEL


DIMENSIONTO SUITINSTALLATION4

4

NOTE:Use Only Two Vandal Resistant 5/8" SMSTo Diagonally Fasten U-bracket To Pilaster.

FIGURE B

Page 4

25"(APPROX.)

5

FIGURE B2

5


5

5"(APPROX.)

33

1

(4) Plastic Shields


44

FIGURE A

5DIMENSIONTO SUITINSTALLATION

2

FIGURE A

5"(APPROX.)

33

33

44

1

Vandal Resistant 5/8" S.M.S

5"(APPROX.)1

(12)

FLOOR ANCHORED/OVERHEAD BRACEDPANEL TO PILASTER/WALLONE EAR ASSEMBLY

QTYDESCRIPTIONPART ID.

3 Vandal Resistant 2 1/2" S.M.S

5

4

(4)

One Ear Bracket

"U" Bracket2

1

(2)

(2)







5

5

5

5

5

5

5

5

5

5

5

5



NOTE:Replace Vandal Resistant 2 1/2" SMSWith Vandal resistant 5/8"SMSTo Fasten Pilaster To Panel.

ALTERNATE

Page 5

4

3 1

22

4

FIGURE A

3

14

4

Fasten using sheet metal screws.


Establish bottom door openings by adjustingpilaster "L" brackets (anchoring) to desired positionand tightening screws.(See step 6)

FLOOR ANCHORED/OVERHEAD BRACEDPILASTER/WALLASSEMBLY

3

FIGURE ASEE SHOP DRAWINGS FORPILASTER TO WALL SPACING

22

4

3

13

1

22

4

3

(2)1 One Ear Wall Bracket



Plastic Shields

4

(4)

(8)

(4)

3

2

DESCRIPTION

Pilaster/Wall Hardware Kit (P/N 40-8515210G) Includes:CHROME PLATED ZAMAC

PART ID. QTY

4

4

4

4


Pilaster/Wall Hardware Kit (P/N 40-8265211G) Includes:STAINLESS STEEL


KNOCK OUTWITH PLIERS

SEE PAGE 8 FORDOOR APPLICATION3 1


STEP 2

6 35"(APPROX.)

FIGURE A

Page 6

322

77

ATTACH TOPANEL

75

5 ATTACH TOPILASTER

7


336

22

2

STEP 1

SEE SHOPDRAWINGS FORPILASTER TOWALL SPACING

3

FIGURE A5 7

2

5"(APPROX.)3 38

42

5


7

22 4

33

Vandal Resistant 1" S.M.S (4)

Bracket Headrail Satin "F" Zamac

1

4

(1)

1" One Ear Wall Bracket

8

Alcove Clip

7

(2)

(2)

FLOOR ANCHORED/OVERHEAD BRACEDPILASTER/PANEL ALCOVEONE EAR ASSEMBLY



5

Plastic Shields

6

4

(10)

(14)

(10)

1 1/4" One Ear Wall Bracket

2

3

1 (2)

Alcove Hardware Kit (P/N 40-8517310G) Includes:CHROME PLATED ZAMAC

DESCRIPTIONPART ID. QTY

Note: CHROME PLATEDReplace KIt#8517310 with Kit#8517320for two ear panel locations.


4

4

4

4

4

4

4

4TO EASE INSTALLATION, BOTTOMCLIP SHOULD BE ATTACHED TO PANELBEFORE SETTING ON PILASTER.

Alcove Hardware Kit (P/N 40-8267311G) Includes:STAINLESS STEEL

Note: STAINLESS STEELReplace Kit#8267311 with Kit#8267321for two ear panel locations.


OPTIONALTwo Vandal Resistant 5/8" SMSMay be Used (But Not Recommended)To Fasten brackets To Panel.

Page 7

FLOOR ANCHORED/OVERHEAD BRACEDPILASTER/PANEL/PILASTER INLINEASSEMBLY

NOTE:Offset brackets for screw clearance.



14 13

9

1313

8

6

1447

Page 8A

Long keyInstall doorstop and keeperat height toaccept latch pin. FIGURE 2

Short key

5

141710

16

11

(1) 8 Hinge Nut 5/16"

(2) 15 Vandal Resistant S.M.S. 5/8"1513

1217 Latch Concealed Stop And Keeper

16

15

Step Bolt 1/2"

(1)

(1)

14

132

141

3 Vandal Resistant Step Bolts 1 1/4" long13

14 Vandal Resistant Barrel Nut

12 Bumper And Coathook

(5)

(5)

(1)

10

11

Knob Concealed Latch Male w/ spring washer

Knob Concealed Latch Female

9 Box Cam Nylon

(1)

(1)

(1)

1 Hinge Top Pilaster Bracket (1)

7 Hinge Washer External

5

6 Hinge Washer Internal

Hinge Pintle Nylon

(1)

(1)

(1)

3 Nylon Hinge Pin

4 Hinge Botom Pilaster Bracket

2 Hinge Bushing Nylon

(1)

(1)

(1)

DOOR HARDWAREASSEMBLY

(P/N 40-8513500G) Includes:CHROME PLATED ZAMAC


9


Install outsidelatch escutcheon.Note: Remove and disposeof clear plastic ring that keepsspring washer in place, before installing.

Install inside turning knob and secure together with provided screw.

B. Secure upper door hinge (with bushing lip upward) to pilaster with two through bolts and barrel nuts.

A. Secure lower door pilaster hinge (with cam pintle in place) to pilaster with two through bolts.

C. Insert box cam into lower door hinge portion, short key toward edge of door (figure 2)

D. Lowest point of cam pintle sets door "rest" position. Rotate pintle to desired position, then tighten locking nut.

E. Install door by placing the box cam over the hinge pintle. Position top of door over upper pilaster hinge and insert hinge pin until flush with top of door.

Note that the cammed hinge will force the door to rise when opened. Take this into consideration when installing and allow adequate space.

(P/N 40-8263501G) Includes:STAINLESS STEEL

Insert until flush with door. (E.)

ALL MOUNTING STYLESPOWDER COATED / STAINLESS STEEL

NOTE: When door pulls are used (#21, 13), offset pulls either adjacent to or above and below knobs.

Coathooks in non-handicap stalls can be mounted to suit.

14 13

9

1313

8

6

1447

Page 8B

Long keyInstall doorstop and keeperat height toaccept latch pin. FIGURE 2

Short key

5

(2) 22 Vandal Resistant S.M.S. 5/8"

141710

16

16

18 Step Bolt 1/2" (1)

Vandal Resistant Step Bolts 1 1/4" long

21 Pull Handle

13

20 St/St Hinge Pin

(2)

(4)

(1)

(1) 8 Hinge Nut 5/16"

(2) 15 Vandal Resistant S.M.S. 5/8"1513

Door Hardware Kit (P/N 40-8513510G) H/C Includes:CHROME PLATED ZAMAC

18

19

ADA Handle

Bumper

PART ID. DESCRIPTION

(1)

(1)

QTY

OUTSWING DOOR HARDWARE PROVIDED FOR OUTSWING DOORS.

1217 Latch Concealed Stop And Keeper

16

15

Step Bolt 1/2"

(1)

(1)

14

132

141

20 Vandal Resistant Step Bolts 1 1/4" long13


12 Bumper And Coathook

(5)

(5)

(1)

10

11

Knob Concealed Latch Male w/ spring washer

Knob Concealed Latch Female

9 Box Cam Nylon

(1)

(1)

(1)

1 Hinge Top Pilaster Bracket (1)

7 Hinge Washer External

5

6 Hinge Washer Internal

Hinge Pintle Nylon

(1)

(1)

(1)

3 Nylon Hinge Pin

4 Hinge Botom Pilaster Bracket

2 Hinge Bushing Nylon

(1)

(1)

(1)

DOOR HARDWARE - OUTSWINGASSEMBLY



9


B. Secure upper door hinge (with bushing lip upward) to pilaster with two through bolts and barrel nuts.

A. Secure lower door pilaster hinge (with cam pintle in place) to pilaster with two through bolts.

C. Insert box cam into lower door hinge portion, short key toward edge of door (figure 2)

D. Lowest point of cam pintle sets door "rest" position. Rotate pintle to desired position, then tighten locking nut.

E. Install door by placing the box cam over the hinge pintle. Position top of door over upper pilaster hinge and insert hinge pin until flush with top of door.

Note that the cammed hinge will force the door to rise when opened. Take this into consideration when installing and allow adequate space.


Insert until flush with door. (E.)

ALL MOUNTING STYLESPOWDER COATED / STAINLESS STEEL

21

21

NOTE: When door pulls are used (#21, 13), offset pulls either adjacent to or above and below knobs.

Coathooks in handicap stalls should be no higher than 48" A.F.F.

Door pulls will be thru-boltedwith #13 at a location to suitno higher than 48" above finishedfloor, per ADA.

NOTE: Door pulls will not mate-up.They will have exposed bolt headson opposite door side.

13

13

13

13

5

2

51

5

35

3

4

14

4

5 VandalResistant S/S 5/8" S.M.S (4)

Plastic Shield (2)

1

2

3

Headrail Cap Satin Zamac (1)

Vandal Resistant S/S 2 1/2" S.M.S (2)

Headrail Satin "F" Zamac Bracket (2)

HEADRAILASSEMBLY Headrail Hardware Kit (P/N 40-8448100G) Includes:

DESCRIPTIONPART ID. QTY



43

FIGURE A

224 4

4 2

4

3 1 44

2

3FIGURE A 1

34

2244

33 4

41

QTYPART ID. DESCRIPTION

(4) Plastic Shields3

Vandal Resistant 5/8" S.M.S4 (8)

Two Ear Wall U/S Bracket

Vandal Resistant 2 1/2" S.M.S2

1

(4)

(2)

URINAL SCREENASSEMBLY Urinal Screen Hardware Kit (P/N 40-8511281G) Includes:

CHROME PLATED ZAMAC

Page 10

LC

LC


A. Before proceeding,confirm that backing of wall is adequate to support and secure mounting of urinal screens.Check dwgs for layout.

B. Insert anchoring devices in walls and secure wall brackets with 2 1/2" s.m.s.

C. Place urinal screen on a support, 12" above the floor.

D. Set U/S into wall brackets and fasten urinal screen at this time,using 5/8" fasteners.

Urinal Screen Hardware Kit (P/N 40-8261281G) Includes:STAINLESS STEEL





NOTE: FLOOR MUST BE CONCRETE.

A. Review the layout drawngs and package lists that have accompanied this job.




E. Establish pilaster floor fastener locations from side wall according to shop drawings. (Note floor fasteners are located 1" from edge of pilaster.)

F. Mark wall bracket holes using brackets as templates.

STEP 2WALL BRACKETS AND FLOOR BRACKETS LC

LC LCLC LCLC

LCLC

48"

48"

17"

17"

48"

PANELCENTER LINE

12" SUPPORT

PILASTERCENTER LINE

FIGURE 3


17"

FIGURE 2


FIGURE 1

Page 112171 Liberty Hill Rd.,Eastanollee, GA 30538 Phone:(706)827-2700 Fax:(706)827-2710Website: www.globalpartitions.com Email: [email protected]

A. Drill holes for wall brackets of 1/4" and floor fastenings of 3/8" for fastening devices

supplied.


C. Install wedge anchor with shoe clip washer and nut into concrete floor (min. 2 1/2") and tighten.

STEP 1LAYOUT

FLOOR ANCHOREDPOWDER COATED / STAINLESS STEEL

A. Level each pilaster by adjusting both support nuts to desired position.

B. Plumb each pilaster and fasten the pilaster to panel with "u" brackets using through bolts or sheet metal screws.

C. Establish door openings by setting pilaster mounting channel to desired position on anchor.

D. Tighten locking nuts on top of pilaster mounting channel.

E. Slide stainless steel shoe down to floor level, firmly engaging shoe clips.

F. Remove panel support device.

STEP 6SECURING PILASTERS /PANELS


A. On each wedge anchor thread place one shoe clip and 3/8" support nut down to approximately 1" up from floor level and place round washer over each anchor.

B. Inspect shoe for bowing. Squeeze edges and center of shoe to ensure shoe will not bow away from pilaster faces. Slide stainless steel shoe carefully over mounting end of pilaster and leave approximately 5" above end.

C. Position pilaster on anchors and secure lightly with flat washers and 3/8" locking nuts.

A. Align U-brackets in position on rear of pilasters. Refer to layout drawings for placement.

B. Fasten U-brackets to pilaster with sheet metal screws pre-drilling with 1/8" bit.

C. Pilasters at wall do not require U-brackets,but should be prepared for wall (and floor fastening) as required by compartment layout.


FIGURE 5

LC

FIGURE 4

FIGURE 6

FRONT

REAR


Page 12




5"(APPROX.)





FLOOR ANCHOREDPANEL TO PILASTER/WALLTWO EAR ASSEMBLY

4 1

5"(APPROX.)

33

FIGURE A

4


33

44 1

FIGURE B

NOTE:Use Only Two Vandal Resistant 5/8"SMS To Diagonally Fasten U-bracketTo Pilaster.

FIGURE B

Page 13

5

5

5"(APPROX.)2

2


5

55

Plastic Shields

4


2

FIGURE A

53

5 3

55"(APPROX.) 1

4

Vandal Resistant C/P 5/8" S.M.S (12)

(4)

VandalResistant C/P 2 1/2" S.M.S

5

4

(4)

"U" Bracket2

3

1 Two Ear Bracket

(2)

(2)



5

5

5

5

5

5

5

5




FIGURE B

55"(APPROX.)

5

5"(APPROX.)


3

144

3

NOTE:Use Only Two Vandal resistant 5/8" SMSTo Diagonally Fasten U-bracket To Pilaster.

FIGURE B

Page 14

2

5

2

5

5

5

(4) Plastic Shields

5"(APPROX.)

5

FIGURE A


33


144

5"(APPROX.)

FIGURE A

5

2

33

54

4

1



PART ID.

FLOOR ANCHOREDPANEL TO PILASTER/WALLONE EAR ASSEMBLY

5

3

4

Pilasters must be both plumb and level.

2

1

QTYDESCRIPTION

Vandal Resistant 2 1/2" S.M.S (4)

"U" Bracket (2)

One Ear Bracket (2)A. Plumb pilaster and fasten pilaster to panel using through bolts or sheet metal screws and "U" brackets.

B. Establish bottom door openings by adjusting pilaster and tightening screws.(Refer to step 4 & 6)

C. Remove support device.



5

5

5

5

5

5

5

5

5


(2)1 One Ear Wall Bracket

4


3

2

(4) Plastic Shields


Vandal Resistant 2 1/2" S.M.S (4)


FLOOR ANCHOREDPILASTER/WALL ASSEMBLY


4

FIGURE B

NOTE:Replace Vandal Resistant 2 1/2" SMSWith Vandal Resistant 5/8" SMSTo Fasten Pilaster To Panel Instead Of Wall.

3 1

22

FIGURE A

3

4

4

4

1

3

SEE SHOP DRAWINGS FORPILASTER TO WALL SPACING

22

FIGURE A

13

3

22

1 4

3


4

4

4

4

4

2171 Liberty Hill Rd.,Eastanollee, GA 30538 Phone:(706)827-2700 Fax:(706)827-2710Website: www.globalpartitions.com Email: [email protected] Page 15



NOTE:Replace Vandal Resistant 2 1/2"With Vandal Resistant 5/8"To Fasten Pilaster To Panel.

1 44

33

55

2

33

441

33


44

44

3

SEE PAGE 8FOR DOORAPPLICATION

6FLAT STRIKE& KEEPER#8263100

55

2

5

(4) Plastic Shields


Vandal Resistant 2 1/2" S.M.S (4) 3

6

3

4

6 One Ear Wall Bracket (2)

PART ID.


DESCRIPTION QTY


Note:Replace P/N#40-8515010G with P/N#40-8515020Gfor two ear locations.

FLOOR ANCHOREDPILASTER/PANEL ALCOVE ASSEMBLY

(2)1 One Ear Bracket

5

4

(4) Vandal Resistant 2 1/2" S.M.S

Plastic Shields (4)

3

2 "U" Bracket (2)

PART ID.


DESCRIPTION QTY

FIGURE A

FIGURE A

PILASTERSIDE




5

5

5

5

5

5

5

5

5

5

5

5


FIGURE 1

17"

48"

PANELCENTER LINE

PILASTERCENTER LINE


17"

48"

STEP 1LAYOUTCEILING HUNG

STEP 2WALL BRACKETS


FIGURE 2

FIGURE 3

A. Drill holes for wall brackets of appropriate size for particular fastening devices supplied. Typically 1/4" drill bits can be used throughout.


C. Pilaster at wall should be prepared for wall and ceiling fastening as required by compartment layout.


B. Set it into wall brackets,but do not fasten panel at this time as it may need to be raised or lowered to sit flush with pilaster bottoms.


B. Top of the finished ceiling and bottom edge of structural support should not exceed 1".

C. Before proceeding, confirm that backing of wall and ceiling support is adequate to secure mounting of toilet compartment units.

D. Confirm correct location and condition of threaded ceiling rods. These should project 2" to 2-1/2" below finished ceiling.

E. Establish and mark pilaster and panel center lines in relation to ceiling rod locations and drawings. Bolts will be located 1"


17"

48"

17"

48"

12" SUPPORT

LCLCLC

LCLCLC


from edge of pilaster

CEILING-HUNGPOWDER COATED / STAINLESS STEEL

A. Level each pilaster by adjusting both support nuts to desired position.

B. Plumb each pilaster and fasten the pilaster to panel using through bolts or sheet metal screws.

C. Establish door openings by setting pilaster mounting channel to desired position on stud.

D. Tighten locking nuts on top of pilaster mounting channel.

E. Slide stainless steel shoe up to ceiling level, firmly engaging shoe clips.

F. Fasten panel to wall brackets using through bolts.

G. Remove panel support device.

STEP 6SECURING PILASTERS TO PANELS



A. Align U-brackets in position on rear of pilasters.Refer to layout drawings.

B. Fasten U-brackets to pilaster with sheet metal screws pre-drilling with 1/8" bit.

C. Pilasters at wall do not require U-brackets.

LC

FIGURE 6

FIGURE 4REAR

FRONT


5" above bottom end. mounting end of pilaster and leave approximatelyA. Slide stainless steel shoe carefully over

NOTE: STRUCTURAL STEEL BY OTHERS

B. Thread support nuts and mounting washers over threaded rods to support pilaster mounting bar.

C. Position pilaster and mounting channel on threaded rods and attach lightly with square flat washer, lockwasher and locking nut.


FIGURE B

3

5"(APPROX.)

3

44 1

FIGURE A

5"(APPROX.)

2

5

NOTE:Use Only TwoVandal resistant 5/8"SMSTo Diagonally Fasten U-bracket To Pilaster.

FIGURE B

5

2

5"(APPROX.)

43

3

5"(APPROX.)

4 1

CEILING HUNGPANEL TO PILASTER/WALLTWO EAR ASSEMBLY

Fasten pilaster to panel using through boltswith barrel nuts or sheet metal screws.

Pilasters must be both plumb and level.(do not fasten at this time)

Establish bottom door openings by adjustingpilaster and tightening screws.(Refer to step 6)

PART ID.

5

3

4

2

1




Plastic Shields

"U" Bracket

(4)

(4)

(2)

Two Ear Bracket

DESCRIPTION

(2)

QTY


5

5

2

5

5

1

3

FIGURE A

5

4

3

5

4


5

5

5

5

5

5

5

5


4

3

FIGURE B

5"(APPROX.)

55

2

5"(APPROX.)

2

NOTE:Use Only TwoVandal Resistant 5/8" SMSTo Diagonally Fasten U-bracket To Pilaster.

FIGURE B

5

5

5

5

5

FIGURE A

144

3

2

5"(APPROX.)

FIGURE A

3

41

3

5

(2)"U" Bracket2



Plastic Shields

5"(APPROX.)

33

44 1

4

5

3

(4)

(12)

(4)


One Ear Bracket

CEILING HUNGPANEL TO PILASTER/WALLONE EAR ASSEMBLY

1


(2)

Fasten pilaster to panel usingsheet metal screws.



5

5

5

5

5

5

5

5

5

5




(8)

(4)

(4)

QTY

33

2

1

2

FIGURE A

NOTE:Replace Vandal Resistantt 2 1/2" SMSWith Vandal Resistant 5/8"SMSTo Fasten Pilaster To Panel.

4

4

1 4

4


3 1

2

3

2

FIGURE A

4

22


33

1 4

Plastic Shields



3

4

CEILING HUNGPILASTER/WALLASSEMBLY

One Ear Wall Bracket


PART ID.

1

2

DESCRIPTION

(2)


4

4

4

4



4 1

NOTE:Replace Vandal Resistant 2 1/2" SMSWith Vandal Resistant 5/8" SMSTo Fasten Pilaster To Panel.



6

44

633

55

1

4


144

33


43

3

55

33

4

1

4

5

Plastic Shields (4)

(8)

(4)





Note:Replace P/N#40-8515010G with P/N#40-8515020Gfor two ear locations.

PART ID.

3

6

DESCRIPTION


5

3

4 Plastic Shields

CEILING HUNGPILASTER/PANEL ALCOVEASSEMBLY

2

1

PART ID.

"U" Bracket

One Ear Bracket

DESCRIPTION

QTY

(2)

(12)

(4)

(4)

(2)

(2)

QTY

FLAT STRIKE& KEEPER#8263100FIGURE A

FIGURE A

PILASTERSIDE




5

5

5

5

5

5

5

5

5

5

5

5


STEP 1LAYOUTFLOOR AND CEILING ANCHORED

STEP 2WALL BRACKETS AND FLOOR BRACKETS

A. Drill holes for wall brackets and floor fastenings of appropriate size for particular fastening devices supplied. Typically 1/4" drill bits can be used throughout.


C. Insert anchors and ceiling bolts. Position shoe clips and "L" brackets . Details in STEP 5.

(Note ceiling "L" brackets engraved for identification)




17"

FIGURE 3

PILASTERCENTER LINE


48"


PANELCENTER LINE

CEILINGFASTENERLOCATIONS

PILASTERCENTER LINE

FIGURE 2

17"

48"

17"

48"

FIGURE 1





E. Establish pilaster floor and ceiling fastener locations from side wall according to shop drawings. (Note fasteners are located roughly 1" from lockstrip edge of pilaster.)


12" SUPPORT

17"

48"

LCLCLC

LCLCLC


FLOOR TO CEILINGPOWDER COATED / STAINLESS STEEL

A. Plumb each pilaster by adjusting self tapping screws at top & bottom to desired position & tighten.

B. Fasten the pilaster to panel using sheet metal screws.

C. Establish door openings by setting pilaster to desired position. (Refer to layout drawings)

D. Slide stainless steel shoe up to ceiling level & down to floor level, firmly engaging shoe clips.

E. Fasten panel to wall brackets using sheet metal screws.

F. Remove panel support device.

NOTE:STRUCTURAL STEEL BYOTHERS

A. Slide stainless steel shoescarefully over mounting ends ofpilaster and leave approximately 5"space from end.

B. Place pilaster between "L"brackets adjust jack leveling boltand fasten loosely with screws atpredrilled locations at each side.


FIGURE 5

LCA. Align U-brackets in position on rear of pilasters.Refer to layout drawings.

B. Fasten U-brackets to pilaster with sheet metal screws.

C. Pilasters at wall do not require U-brackets,but should be prepared for wall (floor & ceiling fastening) as required by compartment layout.


FIGURE 4REAR

FRONT

STEP 6SECURING PILASTERS TO PANELS

FIGURE 6



4 1

FIGURE B

5

5"(APPROX.)2

5"(APPROX.)


33

NOTE:Use Only TwoVandal Resistant 5/8" SMSTo Diagonally Fasten U-bracket To Pilaster.

FIGURE B

52

5

55


2

FIGURE A


5


5"(APPROX.)

144

33

5"(APPROX.)

4

FIGURE A

5

5

5

51

4

FLOOR AND CEILING ANCHOREDPANEL TO PILASTER/WALLTWO EAR ASSEMBLY

Fasten pilaster to panel using sheet metal screws.




PART ID.


5

3

4

2

1

Vandal Resistant C/P 5/8" S.M.S (12)

Vandal Resistant C/P 2 1/2" S.M.S

Plastic Shields

"U" Bracket

(4)

(4)

(2)

Two Ear Bracket

DESCRIPTION

(2)

QTY

5

5

5

5

5

5

5

5




FIGURE B

5"(APPROX.) 2

FIGURE B

5

5"(APPROX.)


33

144

5

FIGURE A


2

5"(APPROX.)

33


5"(APPROX.)44 1

FLOOR AND CEILING ANCHOREDPANEL TO PILASTER/WALLONE EAR ASSEMBLY




PART ID.

5

3

4

2

1




Plastic Shields

"U" Bracket

(4)

(4)

(2)

DESCRIPTION

One Ear Bracket

QTY

(2)


FIGURE A

NOTE:Use Only Two Vandal Resistant 5/8"To Diagonally Fasten U-bracket To Pilaster.

52

5

55

4

5

1

33

5

4


5

5

5

5

5

5

5

5


3 1

22

FIGURE A

3


22

3 13

FLOOR AND CEILING ANCHOREDPILASTER/WALLASSEMBLY




PART ID.

4

3

2

1



Plastic Shields

(8)

(4)



DESCRIPTION

(4)

(2)

QTY


ALTERNATENOTE:Replace vandal Resistant 2 1/2" SMSWith Tamper Resistant 5/8" SMSTo Fasten Pilaster To Panel.

4

4

4

41

FIGURE A

4

22

341

3





3 1


FIGURE A

STEP 2

6

35"(APPROX.)

32

2

775

ATTACH TOPANEL

7

ATTACH TOPILASTER

STEP 1

5

22


336

2

7


FIGURE A5 7


35"(APPROX.)

5

22

7

3 13

FLOOR AND CEILING ANCHOREDPILASTER/PANEL ALCOVEASSEMBLY

NOTE: Use 40-8517320G for two ear alcove.

Alcove Hardware Kit (P/N 40-8267311G) Includes:STAINLESS STEEL

Alcove Hardware Kit (P/N 40-8517310G) Includes:CHROME PLATED ZAMAC

8

7

6

5

2

4

3

1

PART ID.

Bracket Headrail Satin "F" Zamac (NOT USED FOR FTC) (1)

1" One Ear Wall Bracket

Vandal Resistant 1" S.M.S

Alcove Clip

(4)

(2)

(2)

(10) Vandal Resistant 2 1/2" S.M.S


Plastic Shields

(14)

(10)

1 1/4" One Ear Wall Bracket

DESCRIPTION

(2)

QTY



TO EASE INSTALLATION, BOTTOMCLIP SHOULD BE ATTACHED TO PANELBEFORE SETTING ON PILASTER.

OPTIONALTwo Vandal Resistant 5/8" SMSMay be Used (But Not Recommended)To Fasten brackets To Panel.

FLOOR AND CEILING ANCHOREDPILASTER/PANEL/PILASTER INLINEASSEMBLY



OPTIONAL FULL HEIGHTPANEL TO PILASTER/WALLTWO EAR ASSEMBLY

DESCRIPTION

Panel Hardware Kit (P/N 8446020) Includes:ALUMINUM FULL HEIGHT

PART ID. QTY

Panel Hardware Kit (P/N 8266020) Includes:STAINLESS FULL HEIGHT



hole location tosuit installation

(12) 5 Vandal Resistant 2 1/2" S.M.S

7 Vandal Resistant 5/8" S.M.S

6 Plastic Shields

(12)

(12)


2

3 Vandal Resistant Step Bolts 1" Long

"U" Bracket

(12)

(1)

(12)

1 Two Ear Bracket (1)

3 55

466 5

66

3 5

6 46

3 55

4

4

3 55

66 1

3

7 4

3

7 4

7

3

4

3

7 42

Optional Panel Kit (P/N 8XX 6010) Includes:(1) Ear Bracket

2171 Liberty Hill Rd. Eastanollee, GA 30538 Phone:(706) 827-2700 Fax:(706) 827-2710Website: www.globalpartitions.com Email: [email protected]

Under no circumstances should these components besubjected to:

*Abrasive powders or pads*Water closet cleaners*Ceramic tile cleaners

*Solutions containing more than 1% by volume ofammonia

*Solutions containing acids or lye*Solutions containing enzymes

Attention to work progress during new construction orrenovation is important.

Other trades and cleaning services may use agents forceramics and tiles that will damage these components

In order to provide toilet partitions with thecare and maintenance, the following instructions

must be followed.

A. All surfaces must be kept clean with water and amild soap solution only.

B. In order to provide toilet partitions with the propercare and maintenance, the above instructions must be

followed.

WARNING

CARE AND MAINTENANCE OFTOILET PARTITIONS

Page 31

installation instructions forinstallation 3 3 4 4 1 figure b note: use only two vandal resistant...

Documents