installation instructions - contech lighting · dl70 70" 68.25" distance between adjacent...
TRANSCRIPT
INSTALLATION PROCEDURES1. Do not provide electrical power to the system until ALL
connections have been made. 2. Each linear fixture utilizes two mounting stems. One
stem is used for providing power and support to the fixture. The other stem provides support only. (Figure 1)
3. Refer to linear fixture drawing and chart (Figure 2) to determine stem mounting hole distances based upon fixture length. Fixture can be field cut if shorter length is needed. See attached cutting instruction sheet.
4. Drill mounting holes as shown. Refer to the dimensions to ensure proper fixture clearance from case walls. (Figure 3)
5. Secure stems to case mounting surface using supplied lock washers and nuts. If a slight adjustment is required to attach stems to fixture, there is a movable insert on the threaded support side of the linear fixture. This will provide up to 1/8" adjustment. Install fixture onto stems by pushing the electrical side onto stem, and by screwing threaded stem into fixture with a clockwise motion. (Figure 4)NOTE: if you are installing fixture into a case with a top already in place, ensure you have at least 1/2" clearance between final fixture height and case inside top. This will allow fixture to clear mounting stems for final attachment.
6. Connect cord from electrical stem to power supply utilizing the supplied connector. (Figure 5)
7. The system is now ready to be energized
IMPORTANT SAFETY INSTRUCTIONS:• Read all the instructions before installation. Save instructions for
later use.• Turn off power at fuse or circuit breaker box before installation
or before doing any maintenance work.• Do not exceed the nominal supply voltage or amperage rating.• Do not install any lampholder closer than 6" from any curtain or
similar combustible material.• Warning: Risk of burns. Lamps are extremely hot when lit. Allow
lamps to cool down in temperature before handling. • Product must be mounted in locations and at heights and in a
manner consistent with its intended use, and in compliance with National Electrical Code and local codes. Use of accessory equipment is not recommended.
• Installing contrary to instructions may cause unsafe conditions.• Warning: Risk of fire. Most dwellings built before 1985 have
supply wire rated at 60°C. Consult a qualified electrician before installation.
• To avoid hazards to children, account for all parts and properly dispose of all packing materials.
• Call the Technical Support department at ConTech Lighting with any installation questions: 847.559.5500.
DL INSTwww.contechlighting.com1-847-559-5500 This document can be recycled.
LL2
1-1/4"
7/8"
7/8"7/8"
ConTech Model L L2 DL34 34" 32.25" DL46 46" 44.25" DL58 58" 56.25" DL70 70" 68.25"
Distance between
adjacent mounting holes
L2
≥ 1"
≥ 1"
≥ 3/
16" -
11/
16"
Mou
ntin
g Su
rfac
e
thic
knes
s
≥ 9/16"
11/16"~7/8"
For the ConTech Lighting DL Series LED Linear Display Fixture: DL34, DL46, DL58, DL70
INSTALLATION INSTRUCTIONS
All specifications subject to change without notice. For ConTech’s limited product warranty, go to www.contechlighting.com. For a printed copy of the warranty, call 1-847-559-5500.
4
5
LED Power supply
DL INSTwww.contechlighting.com1-847-559-5500 This document can be recycled.
For the ConTech Lighting DL Series LED Linear Display Fixture: DL34, DL46, DL58, DL70
INSTALLATION INSTRUCTIONS
All specifications subject to change without notice. For ConTech’s limited product warranty, go to www.contechlighting.com. For a printed copy of the warranty, call 1-847-559-5500.
For the ConTech Lighting DL Series LED Linear Display Fixture: DL34, DL46, DL58, DL70
FIELD CUTTING PROCEDURES
DL INST
Continued
www.contechlighting.com1-847-559-5500 This document can be recycled.
Parts to prepare:
Cutting:
Terminal A: 1 piece Terminal B: 1 piece
Base Plate: 1 piece
Base Plate
Cover: 1 piece
Cover
LED Strip: 1 piece
Screws: 4 pieces
5/32" 2-23/32"
Remove the paper from the double-sided adhesive on the printed circuit board (PCB)
Adhere to grooved side of base plate
Install the showcase light module:
Smooth SideGrooved Side
INSTALLATION INSTRUCTIONS
All specifications subject to change without notice. For ConTech’s limited product warranty, go to www.contechlighting.com. For a printed copy of the warranty, call 1-847-559-5500.
FIELD CUTTING PROCEDURES
IMPORTANT SAFETY INSTRUCTIONS:• Read all the instructions before installation. Save instructions for later use.• Turn off power at fuse or circuit breaker box before installation or before doing any maintenance work.• Product must be grounded to avoid potential electric shock and any other potential hazards.• Product must be mounted in locations and at heights and in a manner consistent with its intended use, and in compliance with National Electrical Code and local
codes. Use of accessory equipment is not recommended.• Installing contrary to instructions may cause unsafe conditions.• Do not block light from the trim aperture, in whole or in part, as this may cause unsafe conditions.• Warning: Risk of fire. Most dwellings built before 1985 have supply wire rated at 60°C. Consult a qualified electrician before installation.• Avoid hazards to children: account for all parts and properly dispose of all packing materials.• Call the Technical Support department at Con-Tech Lighting with any installation questions: 847.559.5500
DL INSTwww.contechlighting.com1-847-559-5500 This document can be recycled.
Install the plug-in component:
Remove the release paper on the PCB Connect the PCB to the showcase light module
4Terminal B
Install Terminal B:
Mount the Cover:
Install Terminal A:
Slide Terminal B onto the end of the base plate with showcase light module installed. Hide cables within the terminal.
Slide Terminal A onto the end of the base plate with showcase light module installed.
Slide cover into groves as shown Push cover into Terminal B
Insert self tapping screws and securely tighten
Insert self tapping screws and securely tighten
5
6
7
For the ConTech Lighting DL Series LED Linear Display Fixture: DL34, DL46, DL58, DL70
INSTALLATION INSTRUCTIONS
All specifications subject to change without notice. For ConTech’s limited product warranty, go to www.contechlighting.com. For a printed copy of the warranty, call 1-847-559-5500.