installation instructions bongiovi acoustics dps – gm …2007 – current gmc yukon (6 speaker)...

INSTALLATION INSTRUCTIONS

2000-3802 Instructions 10-11-12.doc of 15

Bongiovi Acoustics DPS – GM 30-Pin Harness (Kit part number 2000-3802) Applications Covered:

2008 – Current Buick Enclave (6 speaker) 2007 – Current Chevy Avalanche (6 speaker) 2006 – Current Chevy Impala (6 speaker) 2007 – Current Chevy Silverado (6 speaker) 2007 – Current Chevy Tahoe/Suburban (6 speaker) 2009 – Current Chevy Traverse (6 speaker) 2007 – Current GMC Acadia (6 speaker) 2007 – Current GMC Sierra (6 speaker) 2007 – Current GMC Yukon (6 speaker)

Kit Contents:

1 bubble bag containing: 1 - DPS Unit

1 bag containing: 1 - DPS Wire Harness

1 bag containing: 1 - DPS Turn-On Switch 2 - 24” Wire Ties

1 bag containing: These instructions 4 - 8.5” Wire Ties

Tools Required: (May Very Depending On Your Vehicle)

T20 Torx Driver 7mm Nut Driver Flat Head Screwdriver Phillips Screwdriver Plastic Trim Tool

NOTE: We strive to provide accurate and up-to-date installation instructions. For the latest full color instructions, as well as an installation video, please visit www.brandmotion.com.



TABLE OF CONTENTS

Pages Kit Components 3

Reference Pin Out for DPS Wiring Harness to DPS Turn On Switch 3

Section 1: Chevy Silverado/GMC Sierra 4 - 6

Section 2: Chevy Tahoe/Suburban/Avalanche and GMC Yukon 7 - 9 Section 3: Chevy Traverse/GMC Acadia/Buick Enclave 10 - 12

Section 4: Chevy Impala 13 - 15 General Preparation: 1. Park vehicle on level ground and secure with tire chucks. 2. Ensure all radio functions are working properly before disassembly. 3. Record any pre-set radio stations if desired since these may be lost as power is disconnected. 4. Remove any CDs to avoid possible jam. 5. Return all Treble, Bass, Fade, and Balance to neutral setting. The DPS is designed to provide the

best audio experience at the neutral settings. You can, however, adjust them to meet your desired experience.

6. For vehicles equipped with automatic transmissions, place shifter in the N (neutral) position and set parking brake.

7. Loosen the negative battery cable bolt. Remove negative battery cable from terminal and position away from battery.



KIT COMPONENTS

Reference Pin Out for DPS Wiring Harness to DPS Turn On Switch (Small Black Connectors)

PIN # FUNCTION

DPS TURN

ON SWITCH

DPS WRING

HARNESS

1 12V Ignition Blue Red 2 12V + Yellow Yellow 3 Ground Black Black 4 Low Voltage Trigger / Speaker Green Purple 5 N/A N/A N/A 6 N/A N/A N/A

Section 1: Chevy Silverado/GMC Sierra Instructions, 2007 – Current


1. Ensure all radio functions are working properly, return all Treble, Bass, Fade, and Balance to neutral settings, and remove any CDs to avoid possible jam before disassembly. 2. For vehicles equipped with automatic transmissions, place shifter in the N (neutral) position and set parking brake. 3. Loosen the negative battery cable bolt. Remove negative battery cable from terminal and position away from battery. 4. Using a plastic trim tool, gently loosen panel under steering column. (Figure 1)

Figure 1

5. Using the plastic trim tool, gently remove IP center trim panel. (Figure 2)

Figure 2

6. Using a 7mm socket driver, remove 6 bolts attaching the radio head unit and HVAC unit. (Figure 3)

Figure 3

7. Pull out the radio head unit and disconnect the 16-pin and 14-pin connectors from the back of the radio. (Figure 4)

Figure 4

8. With the radio head unit pulled out of the way, drop the white connectors DPS harness though the opening behind radio cavity on the right side (Figure 5). Move the console side panel out of the way, and pull the harness through from underneath the dash on passenger side.

Figure 5



9. Connect the male 16-pin and 14-pin connectors from the DPS harness to the vehicles harness. (Figure 6)

Figure 6

10. Connect the female end of the 16-pin and 14-pin connector from the DPS harness to the back of the radio head unit. (Figure 7)

Figure 7

11. Connect the two white connectors to the DPS module. (Figure 8)

Figure 8

12. Connect the DPS turn-on switch to the remaining connector on the DPS harness. (Figure 9)

Figure 9

13. Reconnect negative battery cable. 14. Place DPS module with the Bongiovi DPS Acoustics side face down. Confirm the DPS unit’s dip switches are all set to the down position – “DDDDD”. (Figure 10)

Figure 10

15. Turn vehicle ignition key to “ON” position. Turn on radio head unit for 10 seconds. (Note: There should be no sound from the speakers). Disconnect white 4-pin connector from back of DPS module. (Figure 11)

Figure 11



16. Set the DPS unit’s dip switches for the vehicle’s cab configuration:

A) For Regular Cab Trucks Only: The second and fifth switches should be flipped to the “up” position. “DUDDU”. (Figure 12)

Figure 12

B) For Extend Cab Trucks Only: The first, second, and fifth switches should be flipped to the “up” position. “UUDDU”. (Figure 13)

Figure 13

C) For Crew Cab Trucks Only: “DDUDU”. The third and fifth switches should be flipped to the “up” position. (Figure 14)

Figure 14

17. Plug white 4-pin connector into DPS module and wait 10 seconds. (Note: There should be no sound from the speakers). Disconnect white 4-pin connector from back of DPS module. 18. Plug white 4-pin connector back into DPS module. After a few seconds you should hear sound from the radio. Ensure radio head unit is working properly including all speaker channels.

If you do not hear any sounds, recheck connections and repeat Steps 14 through 18.

19. Disconnect negative battery cable. 20. Using the supplied 24” wire ties, secure DPS module under front of console or behind carpet on passenger side upper foot well. 21. Reassemble vehicle. 22. Reconnect negative battery cable. 23. Place Bongiovi DPS Badge on the left side of radio head unit.

Section 2: Chevy Tahoe/Suburban/Avalanche and GMC Yukon Instructions, 2007 – Current


1. Ensure all radio functions are working properly,

return all Treble, Bass, Fade, and Balance to neutral settings, and remove any CDs to avoid possible jam before disassembly.



4. Using a plastic trim tool, gently remove the IP center trim. (Figure 1)

Figure 1

5. Using a 7mm socket driver, remove the 8 bolts

attaching the radio head unit and HVAC controls. (Figure 2)

Figure 2

6. Pull out the radio head unit and disconnect the 16-

pin and 14-pin connectors from the back of the radio. (Figure 3)

Figure 3

7. With the radio head unit pulled out of the way,

drop the white connectors of the DPS harness though the opening behind radio cavity on the right side (Figure 4). Move the console side panel aside, and pull DPS harness through from underneath the dash on passenger side.

Figure 4

8. Connect the male 16-pin and 14-pin connectors

from the DPS harness to the vehicle’s harness. (Figure 5)



Figure 5

9. Connect the female end of the 16-pin and 14-pin

connector from the DPS harness to the back of the radio head unit. (Figure 6)

Figure 6

10. Connect the two white connectors to the DPS

module. (Figure 7) Figure 7

11. Connect the DPS turn-on switch to the remaining connector on the DPS harness. (Figure 8)

Figure 8

12. Reconnect battery of vehicle. 13. Place DPS Module with the Bongiovi DPS Acoustics

side is face down. Then confirm the DPS Unit’s dip switches are all set to the down position –“DDDDD”. (Figure 9)

Figure 9


Figure 10



15. Set the DPS dip switches for your specific vehicle as follows:

A) Chevy Tahoe/Suburban and GMC Yukon Only. The first, second, and fourth switches should be flipped to the “up” position – “UUDUD”. (Figure 11)

Figure 11

B) Chevy Avalanche Only. The third and fifth switches should be flipped to the “up” position – “DDUDU”. (Figure 12)

Figure 12

16. Plug white 4-pin connector into DPS module and wait 10 seconds. (Note: There should be no sound from the speakers). Disconnect white 4-pin connector from back of DPS module.

17. Plug white 4-pin connector back into DPS module. After a few seconds you should hear sound from the radio. Ensure radio head unit is working properly including all speaker channels.


18. Disconnect negative battery cable. 19. Using supplied 24” wire ties, secure DPS module

under front of console or behind carpet on passenger side upper foot well.

20. Reassemble vehicle. 21. Reconnect negative battery cable. 22. Place Bongiovi DPS Badge on the left side of radio

head unit.

Chevy Tahoe/Suburban and GMC Yukon Dip Switch Settings

Chevy Avalanche Dip Switch Settings

Section 3: Chevy Traverse, 2009 – Current Instructions GMC Acadia, 2007 – Current Instructions

Buick Enclave, 2008 – Current Instructions


1. Ensure all radio functions are working properly, return all Treble, Bass, Fade, and Balance to neutral settings, and remove any CDs to avoid possible jam before disassembly.




Figure 1

5. Using a 7mm socket driver, remove the 4 bolts

attaching the radio head unit. (Figure 2) Figure 2

6. Pull out the radio head and disconnect the 16-pin

and 14-pin connectors from the back of the radio. (Figure 3)

Figure 3

7. With the radio head unit pulled out of the way,

drop the white connectors of the DPS harness though the opening behind radio cavity on the right side (Figure 4). Remove the console side panel, and pull harness through from underneath the dash on passenger side.

Figure 4

8. Connect the male 16-pin and 14-pin connectors

from the DPS harness to the vehicle’s harness. (Figure 5)

Figure 5





Figure 6

10. Connect the two DPS harness white connectors to

the DPS module. (Figure 7) Figure 7

11. Connect the DPS turn-on switch to the remaining

connector on the DPS harness. (Figure 8) Figure 8

12. Reconnect negative battery cable. 13. Place DPS Module with the Bongiovi DPS Acoustics

side is face down. Then confirm the DPS unit’s dip switches are all set to the “down” position –“DDDDD”. (Figure 9)

Figure 9


Figure 10

15. Set the DPS dip switches for Chevy Traverse/GMC Acadia/Buick Enclave. The first, second, third and fourth switches should be flipped to the “up” position – “UUUUD”. (Figure 11)

Figure 11







18. Disconnect negative battery cable. 19. Remove passenger hush panel by using a 7mm

socket driver to remove the bolts. 20. Using supplied 24” wire ties, secure DPS module at

front of console. DO NOT mount module to shift linkage or interfere with its operation. (Figure 12)

Figure 12


head unit.

Section 4: Chevy Impala Instructions, 2006 – Current


1. Ensure all radio functions are working properly, return all Treble, Bass, Fade, and Balance to neutral settings, and remove any CDs to avoid possible jam before disassembly.




Figure 1

5. Using a 7mm socket driver, remove the 6 bolts attaching the Radio head unit and HVAC controls. (Figure 2)

Figure 2

6. Pull out the radio head and disconnect the 16-pin and 14-pin connectors from the back of the radio. (Figure 3)

Figure 3

7. With the radio head unit pulled out of the way, drop the white connectors of the DPS harness though the opening behind radio cavity on the right side (Figure 4). Remove the passenger side console panel, and pull through from underneath the dash.

Figure 4

8. Connect the male 16-pin and 14-pin connectors from the DPS harness to the vehicles harness. (Figure 5)

Figure 5




Figure 6

10. Connect the two white DPS harness connectors to

the DPS module. (Figure 7) Figure 7

11. Connect the DPS turn-on switch to the remaining

connector on the DPS harness. (Figure 8) Figure 8

12. Reconnect battery negative cable of vehicle.

13. Place DPS module with the Bongiovi DPS Acoustics side face down. Then confirm the DPS Unit’s dip switches are all set to the “down” position – “DDDDD”. (Figure 9)

Figure 9

14. T urn vehicle ignition key to “ON” position. Turn on radio head unit for 10 seconds. (Note: There should be no sound from the speakers). Disconnect white 4-pin connector from back of DPS module. (Figure 10)

Figure 10

15. Set the DPS dip switches for Chevy Impala. The first and third switches should be flipped to the “up” position – “UDUDD”. (Figure 11)

Figure 11






18. Disconnect negative battery cable. 19. Remove passenger hush panel using a 7mm socket

driver to remove the bolts. 20. Using supplied 24” wire ties, secure DPS module

under front of console or behind carpet on passenger side upper foot well.


head unit.

installation instructions bongiovi acoustics dps – gm …2007 – current gmc yukon (6 speaker)...

Documents