FAMILY CAREINSTALLATION INSTRUCTIONS

3.0/4.8L VITREOUS CHINA ONE PIECE TOILET3.0/4.8

S-TRAP 305mm K-23188T-NSS-TRAP 400mm K-23189T-NS

�

�

�

Please read these instructions carefully to familiarizeyourself with the required tools, materials, and installationsequences. Follow the sections that pertain to yourparticular installation. This will help you avoid costlymistakes. In addition to proper installation, read alloperating and safety instructions.

All information in these instructions is based upon thelatest product information available at the time ofpublication. Kohler China reserves the right to makechanges in product characteristics, packaging, oravailability at any time without notice.

These instructions contain important care, cleaning, andwarranty information -

.please leave instructions for the

consumer

�

�

� -

�

ORDERING INFORMATION

Family Care Skirted 1PC 305mm W/O Seat .......K-23188T-NS

Family Care Skirted 1PC 400mm W/O Seat .......K-23189T-NS

Recommended Toilet Seat:

Family Care QC Seat ................................................K-23204T

Family Care Furefresh QC Seat................................K-23205T

305mm( ) ...........K-23188T-NS

400mm( ) ...........K-23189T-NS

.......................................K-23204T

( )..........................K-23205T

-1-©

©

Copyright Kohler China Investment Co., Ltd. 2019

2019

No.2 KOHLER ROAD, SANSHUI CENTRAL INDUSTRIAL PARK, LEPING TOWN, SANSHUI DIST., FOSHAN, GUANGDONG, PRC POST CODE 5281372 528137

8# MENGSHAN RD, ECONOMIC DEVELOPMENT ZONE OF HUANTAI, ZIBO, SHANDONG, CHINA 2564108 256410

NO.1 KOHLER STREET, ECONOMIC DEVELOPMENT ZONE OF FAKU COUNTY, SHENYANG LIAONING PROVINCE, PRC 1104001 110400

:

POST CODE:

POST CODE:

NOTES

�

�

�

�

�

�

�

Observe all local plumbing and building codes.

Shut off the water supply.

Seat post holes are on 140mm centers.

Ensure that the new drain has the correct roughing-indimension. This toilet has a 305/400mm roughing-indimension. .

Closet flange must be 305/400mm on-center from wall.

Carefully inspect the new fixture for any sign of damage.

For new construction, refer to the dimensions infor locating the shut-off valve.

See Roughing-in

installation step

�

�

�

�

�

�

�

140mm

305/400mm( )

305/400mm

�

�

Fixture dimensions are nominal and conform to tolerances

established by ASME Standards (A112.19.2-2018).

This product complies with Q/KCI-006-2018 and GB

25502-2017. Water Efficiency Grade 1.

�

�

ASME (A112.19.2-

2018)

Q/KCI-006-2018 GB 25502-2017

1

1392769-T01-B

-2-

TOOLS AND MATERIALS REQUIRED

(Not supplied)

�

�

�

�

�

�

�

�

�

�

�

�

254mm (10") adjustable wrench

305mm (12") pipe wrench

Metal file (file cut)

Tape measure

Tubing cutter

Level

Hacksaw

Putty knife

Screwdriver

Toilet gasket (wax seal)

Toilet T-bolts (2), 8mm (5/16") diameter

Toilet supply shut-off valve, 10mm(3/8 ) recommended

If the existing toilet does not have a supply shut-off

valve below the tank, install one before installing the new

toilet.

"

The flexible hose needed is supplied. The stop valve and wax

ring are not supplied.

NOTICE:

�

�

254mm

305mm

60cm

�

�

�

�

�

�

�

�

�

�

8mm T 2

10mm

WARNING: Risk of personal injury or productdamage

WARNING: Risk of external leakage

: Handle vitreous china products very carefully.Vitreous china can break and chip if you overtightenbolts and nuts.

. The fill valvenut has been factory-tightened to design specifications.If re-tightening is required, wrench tighten one turnpast finger tight .

Unit: mm:

Reference Value

K-23188T-NS

FRONT OF BOWL

Finished Wall

Supply

229

200

395

OF OUTLETCL

305

700

378

748

299

286

1392769-T01-B

-3-

TO REMOVE EXISTING TOILET

Turn off the water supply. Flush the toilet, and use a spongeto remove the remaining water from the tank and bowl.Disconnect the supply shut-off valve (if present), and removethe old tank and bowl.

( )

Fig.#11

INSTALLATION

K-23189T-NS

Kohler reserves the right to change marked dimensions without prior notice.

Fig.#22

Remove the old gasket from the floorand the closet flange with a putty knife.Remove the old T-bolts and discardthem.

if the new toilet is notinstalled immediately, temporarily stuffa rag into the closet flange.

NOTICE:

T

NOTICE: Do not use white cement or high lime contentcements to install this toilet. The expansion of cement due toa rise in temperature may make the toilet crack or causedamage. Kohler is not responsible for any damage caused byinstallation with the use of cement.

Closet Flange

67mm;

229mm 200mm

Fig.#33

TO INSTALL SUPPLYSHUT-OFF VALVE

Install the supply shut-off valve so it is229mm above the finished floor line,and 200mm to the left of the closetflange centerline.

The centerline of the supply shut-offvalve outlet should extend 67mm fromthe finished wall. Install the supplyshut-off valve with the outlet vertical.

Supply Shut-Off Valve

Closet FlangeCenterline

200

305/400

229

OF OUTLETCL

FRONT OF BOWL

Finished Wall

Supply

400

229

200

395

748

204

382

700

378

1392769-T01-B

-4-

10mm

5

TO INSTALL BOWL

Position the template and align with

drain hole.

Mark down the position of foot and 5

holes.

Drill holes on ground with the drill of10mm (3/8"), then insert anchor toholes.CAUTION: Please make sure there isno water pipe or spool under the 5holes to be drilled.

Fig.#77

Firmly press the toilet gasket onto thetoilet outlet of plastic trap.

Wax ring type toilet gasketshould not be installed at temperaturesless than 21 C.

If you are using a toiletgasket with an integral plastic sleeve,make sure the gasket is positionedwith the sleeve facing away from thetoilet.

NOTE 1:

NOTE 2:

o

1

21

2

oC

Install brackets.

Plastic Trap Outlet

Toilet Gasket

Fig.#88

Install plastic to ground and mounted

with 3 set of bolts firmly.(not supplied)

3 (

)

NOTE: Must use the toilet installationgasket ring (not supplied) to seal thearea where the waste pipe contactsthe construction section to avoidleakage.

(

)

Fig.#44

Fig.#55

Drain Hole

3/810mm

Fig.#66

1392769-T01-B

Thread the supply hose onto the fill

valve shank.

Fig.#99

Slide nut of inlet cover onto the supply

hose, with flared end last and run hose

through toilet wall.

Fig.#1010

Take hose guide apart and slide onto

the supply hose, with the flared end

last. Slide the two inserts into the

flared end of the hose guide. Insert

into toilet wall and tighten nut.

Fig.#1111

Hose Guide

Fig.#1212

Carefully align and lower the bowl.Apply weight to the bowl rim to let theoutlet insert into plastic trap.

Outlet

Plastic Trap

-5-1392769-T01-B

-6-

Fig.#1313

Carefully thread the screws into the

brackets, until toilet is secure.

Alternately tighten left and right sides

to prevent pulling the toilet off center.

Install cap to cover screw.

Do not overtighten.

Cap ScrewBushing

Fig.#1414

Apply caulk around base.

TO CONNECT WATERSUPPLY

* Flexible hose are recommended toconnect the supply line to the fill valve.If you use a rigid connection (notprovided), take care not to apply sideforces to the bottom of the fill valve. Besure the rigid connection must be fitwith supply line completely to preventdamage shank by forced connection.

(

)

Supply Shank*

Supply Shut-Off Valve

Fig.#1515

IMPORTANT:

Make certain the top is turned to the lockedposition. Valve may not turn on if top is not fully in thelocked position.

Before turning on the supply valve for the firsttime, follow the steps below to clear sand, debris and rustfrom the system:

Make sure water supply is off. Remove valve END byrotating it 1/8 turn counterclockwise.

While holding a container over the uncapped VALVE toprevent splashing, turn water supply on and off a few times.Leave water supply off.

Replace END by engaging lugs and rotating 1/8 turnclockwise.

Turn on water supply. Check that water level is at the markedwater line.

1/8

1/8

1392769-T01-B

Install the toilet seat according to the

seat manufacturer's installation

instructions.

Connect the push button and flush

valve.

Fig.#1616

Fig.#1717

-7-

FILL VALVE ADJUSTMENTFill float with ballast

Adjust the cam clockwise or counter-clockwise until the water level is at themarked water line.

Test flush the toilet.

Check all connections for leakage forseveral days.

Set the tank cover in place on the tank.

PUSH BUTTON INSTALLATION

NOTE: Remove the package and screw out the nut. Make the

button through the tank cover as shown. Be noted that the

button shall be kept level. Arrange big and small flush buttons

according to the label of water consumption on the tank.

Tighten the nut from beneath the tank cover.

Fig.#1818

1392769-T01-B

TANK COVER INSTALLATION

Note: Press down the spring and insert the button into theinstallation position on the tank cover. Release the spring tolock it. Be noted not to let the steel wire of the flush valveresting on the lever of the fill valve.

Fig.#1919

-8-

SYMPTOMS CORRECTIVE ACTION

1. Poor Flush A. Adjust the tank water level to match the waterline.B. Fully open the water supply shut-off valve.C. Clear obstructions from the trapway, jet, or bowl rim holes.D. Clear obstructions from the waste line.

A. Adjust the chain for proper slack so the seal is not held off the flush valve seat.

B. Clean or replace the seal if it is worn, dirty, or misaligned with the flush valve seat, or

if the flush valve seat is damaged. Replace the flush valve seal or flush valve.

C. Clean the fill valve seat/seat washer of debris, or replace the piston/seat washer

assembly.

D. Remove the tank and tighten the flush valve nut if flush valve gasket is leaking. Do

not overtighten. If leakage continues, replace the gasket.

E. Adjust the tank water level if it is too high.

2. No Flush

IMPORTANT: Use only genuine Kohler parts as shown to avoid property damage.

4. Tank takes excessive time to fill.

5. There is excessive noise when thetank is filling.

3. The fill valve turns on/off by itselfwithout the toilet being flushed, or itruns allowing water to enter the tank.

A. Reconnect the chain to the trip lever or flush valve.

B. Adjust the chain assembly to remove excessive slack.

A. Fully open the water supply shut-off valve.B. Clean the valve inlet, valve head, or supply line. Flush the lines.

A. Partially close the water supply shut-off valve if the water pressure to the toilet is toohigh. Check the toilet performance following any such adjustment.

B. Remove dirt or obstructions from the valve head. Flush the lines.

Spring

1392769-T01-B

-9-

1. A.

B.

C.

D.

A.

B.

C. /

D.

E.

2.

4.

5.

3. /

A.B.

A.

B.

A.

B.

( )

0 Co

CONSUMER RESPONSIBILITIES

If you live in a hard water area, make certain that the holes inthe toilet rim are kept clean to ensure proper bowl flushing.Toilet bowl cleaners should be used at least once a week.Use a long-handled brush to clean the rim holes, and to cleanas far into the trap as possible to prevent mineral depositsfrom forming.

Most toilet bowl cleaners are not harmful to the vitreous chinasurface of the toilet bowl. Please follow the bowl cleanermanufacturer's instructions carefully.

Do not use abrasive cleaners or solvents.

Do not use in-tank cleaners. Products containingchlorine (calcium hypochlorite) can seriously damagefittings in the tank. This damage can cause leakageand property damage.

Kohler Company shall not be responsible or liable for anydamage to these tank fittings caused by the use of cleanerscontaining chlorine (calcium hypochlorite).

WARNING: Risk of property or product damage.

'

Please do not use hard materials (likescouring pad) to clean product surface, especially theproduct logo.

CAUTION:

CAUTION: Don t use any cement while installingthe toilet.

WARNING: Risk of product damage.

Heat expansion of the toilet may damagethe feet of the toilet. Kohler will not be responsible forany damage because of using cement.

Do not throw into the toilet what is easy to block it,such as newspaper, paper pilch, sanitary towel.Do not bump the vitreous china with great force toprevent it from damaging and leaking.Do not use the product in the water below 0 C.

o

1392769-T01-B