Network Speed Dome Camera

Installation Guide (V1.1)

Installation Guide This installation guide provides instructions for installing the Network Speed Dome Camera on your network. For other aspects of using the product, please refer to the User’s Manual, available on the CD included in this package, or from www.networkipcamera.com Installation Steps Follow the below steps to install the network speed dome camera on your local network (LAN):

1. Check the package contents against the list below 2. Connect the network speed dome camera. 3. Set an IP address with IP installer 4. Set the ID and password.

Package Contents Check the items supplied with your network speed dome camera against the following list. Item Notes Speed Dome camera Outdoor network speed dome camera Printed Materials Installation Guide

Warranty Document CD CD-ROM

Software Utility / Manual Cable Power and Ethernet united cable (installed inside camera housing) Bracket Wall Mounting Bracket made by steel

- Speed Dome Camera- - Wall mount Bracket - - CD Rom - - Installation Guide-

Important 1. Network speed dome camera is installed in an outdoor enclosure and the connection cable is

already assembled in a network speed dome camera. 2. Please do not try to disassemble the unit unless it is necessary.

Connections 1. Connect Ethernet and Power cable.

Connect the network speed dome camera to the network using a standard network cable. (Direct or Cross Over cable. Refer to the below configuration)

Connect power using the supplied power adapter. (Insert the power pin connector to deep inside not to be pulled out and check the red LED on)

[Power and Ethernet cable]

2. Connect the camera to a PC

There are two ways to connect the camera to a local network.

2-1. Connect to a PC directly using cross over cable

UNITED CABLE

Ethernet Connector

Power Indicator

Power connector

2-2. Connect to a Local network using Ethernet cable

Note 1. To avoid damaging network speed dome camera, you should connect the Ethernet cable first

and then supply the power 2. Ethernet and power should be inserted into the power and Ethernet united cable. 3. You should check the red LED on the Power and Ethernet United cable turns on.

ETHERNET DIRECT CABLE

Setting the IP address

The network speed dome camera is designed for use on an Ethernet network and must be assigned an IP address to make it accessible. Camera Manager Utility Camera Manager Utility is the recommended method for setting an IP address in Windows. This free application can be used on networks with or without a DHCP server. Camera Manager Utility is a free windows application that discovers and displays network camera on your network. The application can also be used to manually set a static IP address and upgrade. Note that you must install the network speed dome camera on the same network segment (Physical subnet) as the computer running the manager program. Camera Manger Utility is available on the CD supplied with this product, or it can be downloaded from www.networkipcamera.com Assigning the IP address using the Camera Manager Utility To access the camera to a network, you need to assign an appropriate network IP address when you installed the camera for the fist time. Before starting, connect the camera to a computer or a local network, referring to “Assigning the IP address to the Camera” in the supplied Installation Manual

1. Insert the supplied CD-ROM disc into your CD ROM drive.

2. Double-Click the utility folder in the CD-ROM drive.

3. Double-Click the Camera Manager Utility.

4. Start the Camera Manger Utility.

5. Click on the camera you want to assign a new IP address in the list

The network settings for the selected camera are displayed.

6. Enter Admin’s ID and Password (“admin” for both as a factory default)

7. Set the IP address, Gateway, Subnet Mask, 1st and 2nd DNS and Web port.

8. Confirm that all items are correctly set, then click “Change Network Configurations” button.

Assigning IP address by static Check “static” and enter IP address, Default Gateway, Subnet Mask, DNS1 and 2 and Web port and press ‘Change Network Configuration’ to deliver changed network information to camera. Assigning IP address by DHCP Check “DHCP.” When you set the IP address by DHCP, you should recognize the serial number for the camera that you assign the IP address. The IP address assigned by DHCP could be changed according to the network.

DHCP is a protocol for automatic IP address assignment on a network. IP address

assignment Via DHCP may lead to the situation where the IP address changes and you lose contact.

Configure the options for notification of IP address change (under Services) to receive notification

from the network camera when the IP address changes.

Select the camera you want to assign a new IP address in the list.

Enter User ID and Password (“root” for both as default) to change network configuration

Factory Default network settings IP Address: 192.168.1.221

Gateway: 192.168.1.1 Subnet Mask: 255.255.255.0

DNS1: 168.126.63.1 DNS1: 164.124.101.2

Manual Installation with ARP/Ping

1. Acquire an unused IP address on the same network segment your computer is connected to. 2. Locate the MAC address on the gift box, manual and the bottom of the zoom module inside

the outdoor housing. 3. Open a DOS window and type the following commands.

4. Check that the network cable is connected. Start/restart the camera by disconnecting and reconnecting power, which must be done within 1 minute of entering the ARP command.

5. Close the DOS window when you see ‘Reply from 192.168.0.99:…’ or similar. 6. Start your browser, type in http://<IP address> in the Location/Address field and press Enter

on your keyboard.. To open a DOS in Window: from the start menu, select Run…and type cmd (or command in Windows 98/ME). Click OK. To use the ARP command on a Mac OS X, use the Terminal utility, which is found under Application>Utilities.

Windows syntax: Windows example:

arp –s <IP address> <Mac address> ping -1 307 <IP address>

arp –s 192.168.0.99 00-19-26-22-32-10 ping -1 307 <IP address>

UNIX/Linux/Mac syntax:

UNIX/Linux/Mac example:

arp –s <IP address> <Mac address> ping -s 307 <IP address>

arp –s 192.168.0.99 00-19-26-22-32-10 ping -s 307 <IP address>

Accessing the camera from the Internet Once installed, your camera is accessible on your local network (LAN). To access the camera from the Internet, network routers must be configured to allow incoming traffic, which is usually done on a specific port. Please refer to the documentation for your router for further instructions.

Open the Live View through Web browser It is highly recommended to check the connection of network before placing the camera to where you want. Open the Web browser and enter the IP address you assigned using IP installer. The login page will appear if all the process above has done properly.

1 Start the web browser on the computer and type the IP address of the camera you want to monitor.

Log in page of the camera is displayed.

2 Enter the proper User ID and Password and then press “Login” button. You can select the viewer from among ActiveX Viewer, Java applet Viewer whichever is suitable for your system environments and usage. (Enter the user ID and Password “admin” are set at the factory for the administrator)

Resetting to Factory Default Settings To reset the camera to the original default settings, go to the Administrator Tools > Maintenance web page (described in Maintenance, on page 20 in User’s manual) or use the reset button on the camera as described below. Using the reset button Follow the instructions below to reset the camera to factory default settings using reset button.

1. Switch off the camera by disconnecting the power. 2. Disassembly the camera and find the network board inside of the back box. 3. Keep the reset button pressed until the Indicator flashes red and green (this may take up to 5

seconds) 4. Release the reset button 5. When the power indicator goes off, the process is complete and the camera has been reset.

[ Network PCB board inside camera]

Factory reset button

Reset button

Power Indicator

How to disassembly the BGC-2010S

First, loose the dome drive from the back box.

Loose first, the dome drive from the back box.

Loose the bolt on the side of cover with a screw driver and it could be removed lower bubble in a way that turn left to lower bubble softly with both hands then pull out it.

Remove the dome drive from back box.

There are 3 bolts on the body of camera. They should not be full pulled out to prevent missing.

Loose three of round-headed bolts from

the body of camera. It can be out up to about 1cm to prevent missing after loosening all.

Loose the all of bolts and then pull up the lip of dome drive with both hands.

Remove the dome drive from

connecting part.

Assembly the Speed Dome Camera with poll mount pendant

Assembly the Speed Dome Camera with wall mount pendant

www.intellinet-network.com

DISTRIBUTED BY