installation guide: din-en series

DIN-EN SeriesEnclosure for DIN Rail DevicesInstallation Guide

Internal Dimensions of DIN-EN-2X18 Rail EnclosuresDescription

The DIN-EN series of metal enclosures come in three sizes and house two, three, or six DIN rails. Each rail accommodates up to 18 DIN units leaving room for one DIN unit of extra space (18 mm). The extra space provides room for DIN device locking blocks or wiring along the sides of the enclosure. Each DIN-EN includes a removable front cover for easy access.

The DIN-EN is perfect for Crestron® DIN rail products, such as the DIN-AP3, DIN-DALI-2, and DIN-1DIMU4 (all sold separately). Third-party DIN rail devices can also occupy space amongst Crestron devices.

Crestron also offers DIN-EN two stage installation products, comprised of rough-in enclosures and lay-in panels. These products allow for prewiring and rough-in work during construction and lay-in panel installation later.

2-1/8 in(55 mm)

11/16 in(19 mm)

18-15/16 in(482 mm)

10-7/8 in(276 mm)

2-1/4 in(58 mm)

Ground bus

5-3/4 in(147 mm)(inside)

5-7/8 in(150 mm)

5-7/8 in(150 mm)

(2X) Ø 7/16 in(Ø 12 mm)Mounting

holes

Metal, DIN rail,1-3/8 in (35 mm)

wide x5/16 in (7.5 mm)

high x13-1/2 in (342 mm)

long (3x)


holes

(2X) Ø 5/8 in(Ø 16 mm)


1-1/16 in(27 mm)

10 in(254 mm)

Ground bus

12 in(305 mm)


5-1/2 in(140 mm)

(4X) Ø 1/4 in(Ø 6.4 mm)Mounting

holes



high x13-1/2 in (342 mm)

long (2x)


1-1/16 in(27 mm)

Installation

This section shows exterior and interior dimensions of Crestron’s DIN-EN products.

External Dimensions of DIN-EN-2X18 Rail Enclosures (Front, Side, and Bottom View)

12-5/16 in(313 mm)

1/8 in(3.2 mm)

1-3/8 in(35 mm)

(16x) Ø 7/8 in (23 mm) knockouts for 1/2 in (13 mm)conduit (same pattern opposite side)

3-9/16 in(91 mm)

1-5/16 in(34 mm)

4-3/8 in(111 mm)

2-15/16 in(75 mm)

1-3/8 in(35 mm)

2-15/16 in(75 mm)

5 in(127 mm)

3-1/4 in(83 mm)

1-5/16 in(34 mm)

11-1/2 in(293 mm)

14-1/8 in(359 mm)

5 in(127 mm)

2-1/4 in(57 mm)

Additional Resources

Visit the product page on the Crestron website (www.crestron.com) for additional information. Use a QR reader application on your mobile device to scan the QR image.

DIN-EN-6X18-MMOE DIN-EN-6X18-MMP

DIN-EN-2X18 DIN-EN-3X18 DIN-EN-6X18

DIN-EN-3X18-MMOE DIN-EN-3X18-MMP

~5/16 in(24 mm)

7-3/16 in(183 mm)

9-11/16 in(246 mm)

14-3/8 in(365 mm)

2-1/2 in(64 mm)

~1-1/4 in(32 mm)

2-1/4 in(58 mm)

1-1/4 in(32 mm)

Ø 7/8 in (23 mm)knockouts for

1/2 in (13 mm) conduit(typical both sides)

16-1/8 in(409 mm)

24-1/4 in(616 mm)

23-1/2 in(597 mm)

4 in(102 mm)

3-1/16 in(78 mm)

1/4 in(7 mm)

3-1/4 in(83 mm)

4-7/16 in(113 mm)

1-1/8 in(28 mm)knockout

for3/4 in

(20 mm)conduit(typical

bothsides)

External Dimensions of DIN-EN-3X18 Rail Enclosures (Front, Side, and Bottom View)

Internal Dimensions of DIN-EN-3X18 Rail Enclosures External Dimensions of DIN-EN-6X18 Rail Enclosures (Front, Side, and Bottom View)

16-1/8 in(409 mm)

39-5/8 in(1 m)

38-7/8 in(989 mm)

3-1/16 in(78 mm)

4 in(102 mm)

1/4 in(7 mm)

3-1/4 in(83 mm)

4-7/16 in(113 mm)

~5/16 in(24 mm)

7-3/16 in(183 mm)

9-11/16 in(246 mm)

14-3/8 in(365 mm)

2-1/2 in(64 mm)

~1-1/4 in(32 mm)

2-1/4 in(58 mm)

1-1/4 in(32 mm)

Ø 7/8 in (23 mm)knockouts for

1/2 in (13 mm) conduit(typical both sides)

1-1/8 in(28 mm)knockout

for3/4 in

(20 mm)conduit(typical

bothsides)

2-1/8 in(55 mm)

11/16 in(19 mm)

34-3/8 in(873 mm)

10-7/8 in(276 mm)

2-1/4 in(58 mm)

Ground bus

5-7/8 in(150 mm)


5-7/8 in(150 mm)

5-7/8 in(150 mm)

5-7/8 in(150 mm)

5-7/8 in(150 mm)



holes



high x13-1/2 in (342 mm)

long (6x)


holes

(2X) Ø 5/8 in(Ø 16 mm)

Crestron Electronics, Inc. Installation Guide - DOC. 7192B15 Volvo Drive, Rockleigh, NJ 07647 (2030929)Tel: 888.CRESTRON 06.18Fax: 201.767.7576 Speci�cations subject to www.crestron.com change without notice.

Crestron and the Crestron logo are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. UL and the UL logo are either trademarks or registered trademarks of Underwriters Laboratories, Inc. in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography.

This document was written by the Technical Publications department at Crestron.

©2018 Crestron Electronics, Inc.

~2-1/8 in(55 mm)

~18-15/16 in(482 mm)

1-3/4 in(45 mm)

~10-7/8 in(276 mm)

23-1/2 in(597 mm)

(2X) Ø 7/16 in(Ø 12 mm)

Mounting holesfor up to 1/4 in

screws

(2X) Ø 5/16 in (Ø 8 mm)Mounting holes forup to 1/4 in screws

(2X) Ø 5/8 in(Ø 16 mm)

~11/16 in(18 mm)

(4X)Mountingholes for

MMP panel

~15-3/8 in(390 mm)

~15/16 in(24 mm)

~3/8 in(9 mm)

(4X) Ø 7/16 in(Ø 11 mm)

(4X)~5/16 in(9 mm)

~11-13/16 in(300 mm)

~2-15/16 in(75 mm)

~11-13/16 in(300 mm)

~20-1/4 in(515 mm)

~13-11/16 in(347 mm)

~1-9/16 in(41 mm)

(4X) Ø 3/16 in(Ø 6 mm)

Mounting holesfor #10 screws

~2-1/8 in(55 mm)

~34-3/8 in(873 mm)

1-3/4 in(45 mm)

~10-7/8 in(276 mm)

(2X) Ø 5/16 in (Ø 8 mm)Mounting holes forup to 1/4 in screws

(2X) Ø 5/8 in(Ø 16 mm)

~38-7/8 in(988 mm)

~11/16 in(18 mm)

(6X)Mountingholes for

MMP panel

(2X) Ø 7/16 in(Ø 12 mm)

Mounting holesfor up to 1/4 in

screws

~15-3/8 in(390 mm)

~15/16 in(24 mm)

~3/8 in(9 mm)

~36-1/8 in(918 mm)

~13-11/16 in(347 mm)

~1-9/16 in(41 mm)

(6X) Ø 7/16 in(Ø 11 mm)

~11-13/16 in(300 mm)

(6X)~5/16 in(9 mm)

~2-3/8 in(60 mm)

~11-13/16 in(300 mm)

(6X) Ø 3/16 in(Ø 6 mm)

Mounting holesfor #10 screws

~17-11/16 in(450 mm)

Internal Dimensions of DIN-EN-6X18 Rail Enclosures Internal Dimensions of DIN-EN-3X18-MMOE (Rough-In Enclosure)

NOTE: The external dimensions of the DIN-EN-3X18-MMOE are identical to the DIN-EN-3X18 (refer to other side of this sheet).

Dimensions of DIN-EN-3X18-MMP (Lay-In Panel)

Internal Dimensions of DIN-EN-6X18-MMOE (Rough-In Enclosure)

NOTE: The external dimensions of the DIN-EN-6X18-MMOE are identical to the DIN-EN-6X18 (refer to other side of this sheet).

Dimensions of DIN-EN-6X18-MMP (Lay-In Panel)

This product is Listed to applicable UL® Standards and requirements tested by Underwriters Laboratories Inc.

Ce produit est homologué selon les normes et les exigences UL applicables par Underwriters Laboratories Inc.

The product warranty can be found at www.crestron.com/warranty.

The speci�c patents that cover Crestron products are listed at www.crestron.com/legal/patents.

Certain Crestron products contain open source software. For speci�c information, please visit www.crestron.com/opensource.

installation guide: din-en series

Documents