installation and user guide - honeywell

Document 800-06554 – Rev C – 02/11

Installation and User Guide

UltraKey Touch

DVR and PTZ Keyboard ControllerHJC4000

Installation and User Guide

Revisions

Issue Date Revisions

A 08/10 New document.

B 08/10 Document revised for preproduction release.

C 02/11 Document updated for latest software changes. Changes include additions to the PTZ keyboard operations section for Diamond and Intellibus protocols. This is the production release version of this document.

4

UltraKey Touch Installation and User Guide

Document 800-06554 Rev C 502/11

ContentsAbout this Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Overview of the Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Explanation of Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Cautions and Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12FCC Compliance Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Manufacturer’s Declaration of Conformance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

North America. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Europe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Important Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Warranty and Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Finding More Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Typographical Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

1 UltraKey Touch Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Shipping Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17UltraKey Touch Port Connections and Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

DC Power Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Ethernet Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18RS232, RS485 Serial Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19RJ45 Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

UltraKey Touch Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

2 Using the UltraKey Touch Controller. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Logging Onto the Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Using the UltraKey Touch to Navigate the LCD Menus . . . . . . . . . . . . . . . . . . . . . . . . . . 21

3 Connecting UltraKey Touch to a DVR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Navigating the LCD Configuration Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Connect to the UltraKey Touch Using the Serial Port (RS232) . . . . . . . . . . . . . . . . . . . . . . 27

Step 1: Connect to the UltraKey Touch Using the Serial Port . . . . . . . . . . . . . . . . . . 27Step 2: Configure the UltraKey Touch for DVR Use . . . . . . . . . . . . . . . . . . . . . . . 28Step 3: Configure the UltraKey Touch Serial Port Settings . . . . . . . . . . . . . . . . . . . 29

Connect to the UltraKey Touch Using the Serial Port (RS485) . . . . . . . . . . . . . . . . . . . . . . 30Step 1: Connect to the UltraKey Touch Using the Serial Port . . . . . . . . . . . . . . . . . . 30Step 2: Configure the UltraKey Touch for DVR Use . . . . . . . . . . . . . . . . . . . . . . . 32Step 3: Configure the UltraKey Touch for Serial Port Settings. . . . . . . . . . . . . . . . . . 33

Installing and Configuring an Ethernet Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Step 1: Connect to the UltraKey Touch Using the Ethernet Port . . . . . . . . . . . . . . . . 35Step 2: Configure the UltraKey Touch for DVR Use . . . . . . . . . . . . . . . . . . . . . . . 36Step 3: Configure the UltraKey Touch Ethernet Connection Settings . . . . . . . . . . . . . . 36

Keyboard Configuration for Cascade Linkage (Additional) . . . . . . . . . . . . . . . . . . . . . . . . 37Configuring UltraKey Touch Using the Web Browser (Optional) . . . . . . . . . . . . . . . . . . . . . 39

Logging into the Web Browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39Step 1: Configure UltraKey Touch to Standalone Mode . . . . . . . . . . . . . . . . . . . . . 39

6

Contents

Step 2: Standalone Configuration for DVR Settings . . . . . . . . . . . . . . . . . . . . . . . 40Step 3A: Configure the Controller for a Serial Port Connection . . . . . . . . . . . . . . . . . 41Step 3B: Configure the Controller IP for an Ethernet Connection . . . . . . . . . . . . . . . . 42

Controlling a FUSION DVR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43Step 1: Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43Step 2: Select DVR Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43Step 3: DVR and Camera Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44Operating a Fusion DVR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Controlling an HRXD/HRSD DVR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46Step 1: Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46Step 2: Keyboard Setup for Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46Operating an HRXD DVR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Controlling an HRDP DVR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48Step 1: Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48Step 2: Keyboard Setup for Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48Operating an HRDP DVR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

4 Installing UltraKey Touch with PTZ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Navigating LCD Configuration Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51Installing and Configuring a Serial Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Step 1: Connect to the UltraKey Touch Serial Port . . . . . . . . . . . . . . . . . . . . . . . 52Step 2: Configure the Controller for PTZ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54Step 3: Configure Serial Port of the Controller . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Configuring UltraKey Touch Using the Web Browser (Optional) . . . . . . . . . . . . . . . . . . . . . 56Logging into the Web Browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56Step 1: Configure UltraKey Touch to System Configurations . . . . . . . . . . . . . . . . . . 56Step 2: Standalone Configuration for PTZ Settings . . . . . . . . . . . . . . . . . . . . . . . 57Step 3: Configure the Controller for a Serial Port Connection . . . . . . . . . . . . . . . . . . 58

Controlling PTZs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59Step 1: Keyboard Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59Step 2: Camera Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60Operating a PTZ Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

5 System Administration and Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

System Administration Using the Controller LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65Logging in and Navigating to the System Configuration Menu . . . . . . . . . . . . . . . . . 65Setting the Screen Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65Restore Default . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66Updating the Touch Pad Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66Viewing the Firmware Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66Testing the Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

System Administration Using the Web Browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67Logging into the Web Browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67Upgrading the UltraKey Touch Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67Rebooting UltraKey Touch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68Changing the UltraKey Touch Password. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Appendix A DVR Operation Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Fusion Operation Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71HRXD/HRSD Operation Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72HRDP Operation Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73System Configuration Menu Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75


Document 800-06554 Rev C 711/10

FiguresFigure 1-1 UltraKey Touch Port Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Figure 1-2 RJ45 Box Front and Back Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Figure 2-1 UltraKey Touch Controller Keyboard Layout . . . . . . . . . . . . . . . . . . . . . . . . . 22

Figure 2-2 UltraKey Touch Navigation Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Figure 3-1 LCD and LCD Navigation Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Figure 3-2 DVR Configuration Menu Tree. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Figure 3-3 Connecting the Controller for DVR Control . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Figure 3-4 Connecting the Controller for DVR Control Using RS485. . . . . . . . . . . . . . . . . . . 32

Figure 3-5 Ethernet Port Connections to DVR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Figure 3-6 UltraKey Touch Login Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Figure 3-7 System Configuration Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Figure 3-8 Standalone Configuration for DVR Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Figure 3-9 Serial Port Configuration Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Figure 3-10 IP Configuration Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Figure 4-1 PTZ Configuration Menu Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Figure 4-2 RS485 Serial Port Connection PTZ by RJ45 Box . . . . . . . . . . . . . . . . . . . . . . . 53

Figure 4-3 UltraKey Touch Login page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Figure 4-4 System Configuration Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Figure 4-5 Standalone Configuration for PTZ Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Figure 4-6 Serial Port Configuration Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Figure 5-1 Software Upgrade Warning Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Figure 5-2 Change Password Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Figure A-1 System Configuration LCD Menu Tree - All Modes . . . . . . . . . . . . . . . . . . . . . . 75

8

Figures


Document 800-06554 Rev C 902/11

TablesTable 1-1 Shipping Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Table 1-2 UltraKey Touch Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Table 2-1 UltraKey Touch Controller Keys and Controls . . . . . . . . . . . . . . . . . . . . . . . . . 22

Table 2-2 LCD Menu Navigation During Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Table 3-1 Serial Port Com2 (RS232) Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Table 3-2 Serial Port Com2 (RS232) Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Table 3-3 Serial Port Com1 (RS485) Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Table 3-4 RJ45 Box Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Table 3-5 Serial Port Com1 (RS485) Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Table 3-6 RJ45 Ethernet Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Table 3-7 DVR Control CAM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Table 3-8 Operating a Fusion DVR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Table 3-9 Operating an HRXD DVR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Table 3-10 Operating an HRDP DVR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Table 3-11 Joystick Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Table 4-1 Serial Port COM1 Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Table 4-2 RJ45 Box Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Table 4-3 Operations for a PTZ Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Table A-1 Fusion DVR Operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Table A-2 HRXD/HRSD Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Table A-3 HRDP Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

10

Tables


Document 800-06554 Rev C 1102/11

About this Document

In this section:

• Overview of the Contents, page 11• Explanation of Symbols, page 11• Cautions and Warnings, page 12• Important Safety Instructions, page 14• Warranty and Service, page 15• Finding More Information, page 15• Typographical Conventions, page 15

Overview of the Contents

This document contains the following chapters and appendixes:

• Chapter 1, UltraKey Touch Overview, introduces the UltraKey Touch controller.• Chapter 2, Using the UltraKey Touch Controller, provides procedures for logging on

with the Ultrakey Touch controller and using it to navigate the LCD menus.• Chapter 3, Connecting UltraKey Touch to a DVR, explains connecting the controller

to a DVR and using the controller to perform basic DVR configuration.• Chapter 4, Installing UltraKey Touch with PTZ, describes connecting the controller to

a PTZ camera and using the controller to perform basic PTZ camera configuration.• Chapter 5, System Administration and Troubleshooting, covers system

administration using the controller LCD or the web browser.• Appendix A, DVR Operation Commands, lists UltraKey Touch DVR operation

commands and provides a menu tree for the controller’s LCD menus.

Explanation of Symbols

WARNING! The exclamation point in a red octagon is a WARNING. Failure to take or avoid a specific action could result in physical harm to a person or irreparable damage to equipment.

12

Caution The lightning flash with arrowhead symbol within an equilateral triangle alerts the user to the presence of uninsulated dangerous voltage within the enclosure of the product that may be of sufficient magnitude to constitute a risk of electric shock to the person.

Caution The exclamation point in a yellow equilateral triangle is a Caution. Failure to take or avoid a specified action could result in loss of data or damage to equipment and may contain important operating and maintenance servicing information.

Cautions and Warnings

Installation and servicing should be performed only by qualified and experienced technicians to conform to all local codes and to maintain your warranty.

WARNING! 12 VDC/24 VAC models require the use of CSA Certified/UL Listed Class 2 power adapters to ensure compliance with electrical safety standards.

WEEE (Waste Electrical and Electronic Equipment). Correct disposal of this product (applicable in the European Union and other European countries with separate collection systems). This product should be disposed of, at the end of its useful life, as per applicable local laws, regulations, and procedures.


Document 800-06554 Rev C 1302/11

FCC Compliance Statement

Information to the User: This equipment has been tested and found to comply with the limits for a Class B digital device. Pursuant to Part 15 of the FCC Rules, these limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna• Increase the separation between the equipment and receiver• Connect the equipment to an outlet on a circuit different from that to which the

receiver is connected• Consult the dealer or a radio/TV technician for help.

Caution Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Caution Users of the product are responsible for checking and complying with all federal, state, and local laws and statutes concerning the monitoring and recording of video and audio signals. Honeywell shall not be held responsible for the use of this product in violation of current laws and statutes.

This Class B digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada.

Manufacturer’s Declaration of Conformance

North America

The equipment supplied with this guide conforms to UL 60950-1 and CSA C22.2 No. 60950-1.

14

Europe

The manufacturer declares that the equipment supplied with this guide is compliant with the essential protection requirements of the EMC directive 2004/108/EC and the Low Voltage Directive LVD 2006/95/EC, conforming to the requirements of standards EN 55022 for emissions, EN 50130-4 for immunity, and EN 60950 for Electrical Equipment safety.

Important Safety Instructions

BEFORE OPERATING OR INSTALLING THE UNIT, READ AND FOLLOWALL INSTRUCTIONS.AFTER INSTALLATION, retain the safety and operating instructions forfuture reference.1. HEED WARNINGS - Adhere to all warnings on the unit and in the operating

instructions.

2. INSTALLATION

• Install in accordance with the manufacturer’s instructions. • Installation and servicing should be performed only by qualified and

experienced technicians to conform to all local codes and to maintain your warranty.

• Do not install the unit in an extremely hot or humid location, or in a place subject to dust or mechanical vibration. The unit is not designed to be waterproof. Exposure to rain or water may damage the unit.

3. POWER SOURCES - This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied to your facility, consult your product dealer or local power company.

4. HEAT - Situate the unit away from items that produce heat or are heat sources, such as radiators, heat registers, stoves, or other products (including amplifiers).

5. WATER AND MOISTURE - Do not use this unit near water or in an unprotected outdoor installation, or any area classified as a wet location.

6. ATTACHMENTS - Do not use attachments not recommended by the product manufacturer as they may result in the risk of fire, electric shock, or injury to persons.

7. ACCESSORIES - Only use accessories specified by the manufacturer.

8. CLEANING - Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

9. SERVICING - Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

10. REPLACEMENT PARTS - When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.


Document 800-06554 Rev C 1502/11

Warranty and Service

Subject to the terms and conditions listed on the Product warranty, during the warranty period Honeywell will repair or replace, at its sole option, free of charge, any defective products returned prepaid.

In the event you have a problem with any Honeywell product, please call Customer Service at 1.800.796.CCTV for assistance or to request a Return Merchandise Authorization (RMA) number.

Be sure to have the model number, serial number, and the nature of the problem available for the technical service representative.

Prior authorization must be obtained for all returns, exchanges, or credits. Items shipped to Honeywell without a clearly identified Return Merchandise Authorization (RMA) number may be refused.

Finding More Information

Refer to the online literature library to access other electronic documents in PDF format including data sheets, quick references, installation and user guides, specifications, software and product notices: http://www.honeywellvideo.com. Also see the back cover for international web sites and contact details.

Typographical Conventions

This document uses the following typographical conventions:

Font What it represents Example

Use of an arrow between items (>)

Use of an arrow between keys or tabs indicates holding the first key and then pressing the second key, and then releasing the two keys.

On the controller, press Alt > Clr to enter the System Configuration: Standalone Setting menu.

Lucida Values of editable fields that are mentioned in the body text of the document for reference purposes, but do not need to be entered as part of a procedure

The Time from field can be set to Hours:Minute:Seconds.

Text strings displayed on the screen

Syntax

The message Unauthorized displays.

(object) entered

16

Swiss721 BT Bold Words or characters that you must type. The word “enter” is used if you must type text and then press the Enter or Return key.

Enter the password.

Menu titles and other items you select Double-click Open from the File menu.

Buttons you click to perform actions.

Pressing a key on the keyboard.

Click Exit to close the program.

Press and hold Login.

Italic Placeholders: words that vary depending on the situation

user name

Cross-reference to external source Refer to the System Administrator Guide.

Cross-reference within document See Chapter 2, Installation.

Font What it represents Example

Document 800-06554 Rev C 1702/11

1

UltraKey Touch Overview

The UltraKey Touch keyboard controller (HJC4000) is a replacement for the Honeywell HJZTP controller and is compatible with Honeywell DVRs and PTZs.

The UltraKey Touch can control the following types of DVRs and PTZs, depending on the type of connection used:

• DVR: HRDP, HRXD/HRSD, and FUSION DVR.• PTZ Protocol: Pelco P, Pelco D, Diamond, VCL, and Intellibus.

Shipping Checklist

The following items are included with your UltraKey Touch controller shipment. These accessories are required for certain kinds of installations. Use a serial port or an Ethernet RJ45 connection to connect UltraKey Touch to a DVR and PTZ.

Table 1-1 Shipping Checklist

Quantity Part Use for...

1 UltraKey Touch keyboard controller All installations.

1 UltraKey Touch installation and user guide

All installations.

1 box Power adapter with plugs for 100-240 VAC, 12 VDC, 50-60 HZ, 1 A, 12 W

Meeting the requirements for the local electrical current being used. Four models are included: • CEE 7/16 (Europlug 2.5 A/250V unearthed) • NEMA 1-15 (North American 15 A/125V ungrounded)• BS1363 (British 13 A/230-240V 50 Hz earthed and fused)• CPCS-CCC (Chinese 10 A/250V)/AS 3112; Australian

10 A/240V).

1 Connector adapter, RJ45 to DB9 female, for RS232

Installations that require backwards compatibility with a DVR.

18


UltraKey Touch Port Connections and Descriptions

Figure 1-1 UltraKey Touch Port Connections

DC Power Port

Supports 12V (±10%) DC/1 A power input. Use the power adapter included with the shipment and insert one of the four adapters, based on your local power requirements.

Ethernet Port

Ethernet is used to connect to the controller or DVR for controlling and web browser configuration.

1 RJ45 network cable, 2 meters All installations.

1 RJ45 box RS485 connection requirements.

Table 1-1 Shipping Checklist (cont’d)

Quantity Part Use for...

Power RJ45 Ethernet RS232 and RS485 Serial Port

81Pins are numbered from left to right

81


Document 800-06554 Rev C 1902/11

RS232, RS485 Serial Port

Note These ports are used to connect to DVR RS232/485 or PTZ RS485 ports.

An isolated surge protector is suggested when using RS485 and when cabling between buildings.

RJ45 Box

Use the terminal box RJ45 port and 8-pin terminal plug as required for compatibility and connectivity options. It can be used to break out the RJ45 cable when wiring to existing infrastructure is required.

Figure 1-2 RJ45 Box Front and Back Ports

20


UltraKey Touch Specifications

Table 1-2 UltraKey Touch Specifications

Parameter Value

Power Requirement 10.8 to 13.2 VDC @ 1 Ampere (A)

Connector Types 1 × Ethernet (10Base-T, 100Base-TX) RJ45 with LED

1 × RS232/485 RJ45 with LED

LCD Type: STN, Positive Image

Backlight: Blue-White

Characters: 122 × 32 dots

Compliance EN 55022 for radiated and conducted emissions

Mechanical Dimensions: 16.1” (L) × 8.5” (W) × 4.1” (H)408 mm (L) × 215 mm (W) × 105 mm (H)

Gross Weight: 7.05 lb. (3.2 kg)

Cover material: ABS + PC (cool gray)

Environment Operating Temperature: 14°F to 131°F (–10°C to +55°C)

Storage Temperature: –40°F to +167°F (–40°C to +75°C)

Humidity: 0 to 95% RH (non-condensing)

Document 800-06554 Rev C 2102/11

2

Using the UltraKey Touch Controller

You may need to learn how to use the UltraKey Touch both before and after you begin configuring. This section covers:

• Logging Onto the Controller on page 21• Using the UltraKey Touch to Navigate the LCD Menus on page 21

Logging Onto the Controller

1. Connect the keyboard with a power adapter (12V [±10%] DC/1 A included).

2. Press Login on the keyboard.

3. Enter the password, 1234.

4. Press Alt>Clr to configure the main menu settings.

Note If an invalid password is entered, a message displays and the controller buzzes. Repeat the steps to log in.

Using the UltraKey Touch to Navigate the LCD Menus

There are a variety of ways to navigate the LCD menus during configuration as well as normal operation. See Figure 2-2 for a brief overview of the three main navigation options. See Table 2-2 for specific methods of navigating the LCD during installation and set up.

22


Figure 2-1 UltraKey Touch Controller Keyboard Layout

Table 2-1 UltraKey Touch Controller Keys and Controls

No. Icon Description No. Icon Description

1 LCD screen 2 Alarm key

3 Sequence key 4 Iris open / close key

5 Set key 6 Recycle key

7 Backwards key 8 Review key

9 Stop key 10 Search key

11 Forwards key 12 Tour key

13 View key 14 DVR key

15 Split screen key 16 Number keys

17 Enter key 18 Clear key


Document 800-06554 Rev C 2302/11

19 Monitor key 20 Camera key

21 Alt key 22 PTZ Call key

23 Touch pad slider

Operations with the touch pad are described in these instructions as “Slider_Direction”.

24 Focus near / far key

25 Joystick 26 Focus near / far key

27 Monitor B key 28 Monitor A key

29 Login key 30 F1–F10 keys

31 Left key, Up key, Select key, Down key and Right key

Table 2-1 UltraKey Touch Controller Keys and Controls (cont’d)

No. Icon Description No. Icon Description

24


Figure 2-2 UltraKey Touch Navigation Controls

Touch pad slider (used like a laptop mouse pad)

Right arrow key Left arrow key

Backward or reverse key (or down)

Forward key (or up)

Center key is not used for controlling

Right arrow keyLeft arrow key

Up arrow key Down arrow key

Touch Pad and Ring

LCD Keys

Joystick

Move the joystick left and right or up and down to navigate the menus

Touch pad ring

LCD screen

Table 2-2 LCD Menu Navigation During Setup

Task Options

To confirm a change or enter the current menu

You can use any of these methods to change or enter the current menu:• KEYS: Press Ent• TOUCH PAD RING: Press the right arrow key • JOYSTICK: Move right

To cancel an operation or return to the previous level of the menu

You can use any of these methods to cancel or return to the previous menu:• KEYS: Press Alt > Clr • TOUCH PAD RING: Press the left arrow key • JOYSTICK: Move left

To view or switch between the menu items of the same level

You can use any of these methods to switch between menu items:• LCD KEYS: Press up / down arrow keys• TOUCH PAD SLIDER: Rotate your finger clockwise or counterclockwise• TOUCH PAD RING: Press the forward / backward arrows • JOYSTICK: Move up / down

To move back through the menus one level at a time

• KEYS: Press Alt > Clr

To correct errors • KEYS: Press Clr

Document 800-06554 Rev C 2502/11

3

Connecting UltraKey Touch to a DVR

This section covers:

• Navigating the LCD Configuration Menus on page 26• Connect to the UltraKey Touch Using the Serial Port (RS232) on page 27• Connect to the UltraKey Touch Using the Serial Port (RS485) on page 30• Installing and Configuring an Ethernet Connection on page 35• Keyboard Configuration for Cascade Linkage (Additional) on page 37• Configuring UltraKey Touch Using the Web Browser (Optional) on page 39• Controlling a FUSION DVR on page 43• Controlling an HRXD/HRSD DVR on page 46• Controlling an HRDP DVR on page 48

Note For all connections, refer to the applicable DVR user guides for more information.

This section explains how to connect the UltraKey Touch controller to a DVR and how to enter the basic configuration settings specific to that DVR. UltraKey Touch can control the remote DVR through either of the serial port or Ethernet connections. Then you can start configuring the system. Familiarize yourself with these basic operations:

• To confirm a modification or enter the current menu item you can press: Ent, Slider_Right (on the touch pad), or move the joystick to the right.

• To cancel an operation or return to the previous level of the menu you can press: Slider_Left (on the touch pad), Alt > Clr, or move the joystick to the left.

• To view or switch between the menu items of the same level you can press: Slider Up /Down, the LCD up/down arrow keys, rotate the slider, or move the joystick up/down.

26


Navigating the LCD Configuration Menus

Figure 3-1 LCD and LCD Navigation Keys

Figure 3-2 DVR Configuration Menu Tree

Right arrow key

Left arrow key

Up arrow key Down arrow key Numeric keypad and Ent key

System Configuration

Data Bit

NetworkSerial PortStandalone

Settings

DVR / CAM PORT SELECT

HRDP / FUSION / HRXD

DVR PTZ

Baud Rate

Parity Stop Bit

IP Address

COM2 (RS232) Show Net Infor Manual Settings DHCP

Serial SettingsDVR Selection

RS232/RS485

Gateway

NetMask

DNS

Basic Set


Document 800-06554 Rev C 2702/11

Connect to the UltraKey Touch Using the Serial Port (RS232)

Step 1: Connect to the UltraKey Touch Using the Serial Port

Note For a list of cable accessories, see the Shipping Checklist on page 17 and for port connections see UltraKey Touch Port Connections and Descriptions on page 18.

1. Select the applicable adapter plug and insert it into the AC adapter. Push to click it into place.

2. Plug the AC adapter into the controller power port and the adapter into a power source.

3. Connect the RJ45 network cable to the controller serial port and the connector adapter.

4. Connect the serial port of the connector adapter to the serial port of the DVR:

• For backwards compatibility with DVRs, a DB9 male adapter is required and included with your shipment (see Figure 3-3).

• For other DVRs, the installation is a direct connection with the RJ45 network cable, also included with your shipment.

Note To setup cascade linkage for UltraKey Touch, see Keyboard Configuration for Cascade Linkage (Additional) on page 37.

Table 3-1 Serial Port Com2 (RS232) Pin Assignments

Serial Port Type Pin Signal

COM2 RS232 4 RXD

5 GND

6 TXD

28


Figure 3-3 Connecting the Controller for DVR Control

Step 2: Configure the UltraKey Touch for DVR Use

Note Set the DVR type in the Ultrakey Touch configuration to be the same as the connected DVR type. If any other type has been selected, then use the following procedure to select a different DVR type.

1. Install and connect the controller to a power source, if it is not already connected.

2. Press Login, and then enter the password, 1234.

3. From the home screen, press Alt > Clr to enter the System Configuration menu. Scroll the slider or rotate the joystick until System Configuration: Standalone Settings displays.

4. Press Ent and rotate the slider to select DVR.

Serial Port (RS232)

Network cable

RJ45 to DB9Ffor RS232

UltraKey Touch

Network Port Network Port

NETWORK

Network cable

Network cable

Master Slave1

This indicates that the keyboard is in PTZ mode.

CAM 001ST User2

This indicates that the keyboard is in DVR mode.

CAM 001 DVR 1ST User2

System ConfigurationStandalone Settings

Standalone Set:DVR


Document 800-06554 Rev C 2902/11

5. Press Ent to enter the DVR Selection menu. Press the Slider_Up/Down to select the DVR to control.

6. Press Ent to enter the Basic Set menu. Press the Slider_Up/Down until the PORT SELECT submenu displays.

7. Press Ent to enter the Port Select menu, then select the RS232 protocol to control a DVR. Press Ent or Slider_Right to confirm.

8. Return to the home screen. If the keyboard is in PTZ mode after changing to DVR settings, then the home screen displays this message:Select Yes or No to change the work mode of the keyboard. If the keyboard is in DVR mode after changing to DVR settings, then the home screen does not display that message.

Step 3: Configure the UltraKey Touch Serial Port Settings

1. Press Alt > Clr to exit from the DVR configuration menu.

2. Before using the UltraKey Touch keyboard to control Fusion/HRXD/HRDP DVRs, it must be setup to meet the requirements. Set Com2 (RS232) according to Table 3-2.

3. Press Alt > Clr a second time to enter the System Configuration menu.

4. Rotate the slider to scroll through the options (standalone settings, serial port, network, language, slider update, cascade linkage, hardware test, about, and restore default).

5. When you are at the System Configuration: Serial Port menu, press Ent to enter.

DVR SelectionFusion

DVR SelectionHRDP

DVR SelectionHRXD

Basic Set:DVR/CAM

Basic Set:PORT SELECT

Port SelectRS232

Change to DVR mode?Yes

Table 3-2 Serial Port Com2 (RS232) Configurations

Type RS232

Baud Rate 9600

Parity None

DataBit 8

StopBit 1

System ConfigurationSerial Port

30


6. Press the Slider_Up/Down or LCD up/down arrow keys to select Com2 (RS232). Press Ent or Slider_Right to confirm, and Slider_Left to return.

7. The Serial Setting menu displays. Here you can set the Com2 (RS232) settings for parity, baud rate, data bit and stop bit:

a. Press the Slider_Right to select Parity. Press Ent and use the Slider_Up/Down or the LCD up/down arrow keys to select None. Press Ent to save.

b. Press the Slider_Down or the LCD up/down arrow keys to select Baud Rate. Press Ent and use the up/down arrow keys to select 1200, 1800, 2400, 4800, 9600, 19200, 38400, or 57600. Press Ent to save.

c. Press the Slider_Up/down or the LCD up/down arrow keys to select Data Bit. Press Ent and use the Slider_Up/Down to select 7 bit or 8 bit. Press Ent to save.

d. Press the down arrow key to select Stop Bit. Press Ent and use the Slider_Up/Down or the LCD up/down arrow keys to select 1 bit or 2 bit. Press Ent to save.

8. Press Slider_Left to return to the main menu.

Connect to the UltraKey Touch Using the Serial Port (RS485)

Step 1: Connect to the UltraKey Touch Using the Serial Port

Note For a list of cable accessories, see the Shipping Checklist on page 17, and for port connections, see UltraKey Touch Port Connections and Descriptions on page 18.


Serial Port: Com2(RS232)

Serial Settings: Parity

Serial Settings: Baud Rate

Serial Settings: Data Bit

Serial Settings: Stop Bit

Table 3-3 Serial Port Com1 (RS485) Pin Assignments


COM1 RS485 1 T/R+

2 T/R–


Document 800-06554 Rev C 3102/11


3. Connect the RJ45 network cable to the serial port of the controller and the RJ45 box.

4. Connect the pins (RS485+, RS485–) of the RJ45 box to the pins (T/R+, T/R–) of the RS232-RS485 converter using appropriate wire. See Table 3-4 for the RJ45 box pin assignments.

5. Connect the RS232-RS485 converter’s serial port to the DVR’s serial port:

• For backwards compatibility with DVRs, an RS232-RS485 converter is required (see Figure 3-4).

• To use the controller’s RS485 serial port, an RJ45 box is required.


Table 3-4 RJ45 Box Pin Assignments

Pin Signal

1 RS485+

2 RS485–

4 RS232 RXD

5 GND

6 RS232 TXD

32


Figure 3-4 Connecting the Controller for DVR Control Using RS485


Note Set the DVR type in the Ultrakey Touch configuration to be the same as the connected DVR type. If any other type has been selected, then use the following procedure to select a different DVR type.

1. Install and connect the controller to a power source, if it is not already connected.

Serial Port (RS232)

Serial Port (RS485)

Network Cable

Serial Port (RS485)

UltraKey Touch

RS232-RS485 Converter

RJ45 Box

Master Slave1

Network Cable

Network Cable


NETWORK

5 4

3

2

1

6

7

8


Document 800-06554 Rev C 3302/11

2. Press Login, and enter the password, 1234.

3. From the home screen, press Alt > Clr to enter the System Configuration menu. Scroll the slider or rotate the joystick until System Configuration: Standalone Settings displays.

4. Press Ent or rotate the slider to select DVR type.

5. Press Ent to enter the DVR Selection menu. Press the Slider_Up / Down to select the DVR to control.

6. Press Ent to enter the Basic Set menu. Press the Slider_Up/Down until the Port Select submenu displays.

7. Press Ent to enter the Port Select menu, then select the RS485 protocol to controll the DVR, then press Ent or Slider_Right to confirm.

8. Return to the home screen.If the keyboard is in PTZ mode after changing to DVR settings, then the home screen displays this message:Select Yes or No to change the work mode of the keyboard. If the keyboard is in DVR mode after changing to DVR settings, then the home screen does not display that message.

Step 3: Configure the UltraKey Touch for Serial Port Settings

1. Press Alt > Clr to exit from the DVR configuration menu.

2. Before using the UltraKey Touch keyboard to control Fusion/HRXD/HRSD/HRDP DVRs, it must be setup to meet the requirements. Set Com1 (RS485) according to Table 3-5 on page 34.


CAM 001ST User2



System ConfigurationStandalone Settings

Standalone Set:

DVR

DVR SelectionFusion

DVR Selection

HRDP

DVR Selection

HRXD

DVR Selection

Basic Set:DVR/CAM

Basic Set:PORT SELECT

Port SelectRS485

Change to DVR mode?Yes

34


3. Press Alt > Clr a second time to enter the System Configuration menu.

4. Rotate the slider to scroll through the options (standalone settings, serial port, network, language, slider update, cascade linkage, hardware test, about, and restore default).

5. When you are at the System Configuration: Serial Port menu, press Ent to enter.

6. Press the Slider_Up/Down or LCD up/down arrow keys to select Com1 (RS485). Press Ent or Slider_Right to confirm, and Slider_Left to return.

7. The Serial Setting menu displays. Here you can set the Com1 (RS485) settings for parity, baud rate, data bit and stop bit:

a. Press the Slider_Right to select Parity. Press Ent and use the Slider_Up/Down or the LCD up/down arrow keys to select none. Press Ent to save.

b. Press the Slider_Down or the LCD up/down arrow keys to select Baud Rate. Press Ent and use the up/down arrow keys to select 1200, 1800, 2400, 4800, 9600, 19200, 38400, or 57600. Press Ent to save.

c. Press the Slider_Up/Down or the LCD up/down arrow keys to select Data Bit. Press Ent and use the Slider_Up/Down or the LCD up/down arrow keys to select 7 bit or 8 bit. Press Ent to save.

d. Press the down arrow key to select Stop Bit. Press Ent and use the Slider_Up/Down or the LCD up/down arrow keys to select 1 bit or 2 bit. Press Ent to save.

8. Press Slider_Left to return to the main menu.

Table 3-5 Serial Port Com1 (RS485) Configurations

Type RS485

Baud Rate 9600

Parity None

DataBit 8

StopBit 1

System ConfigurationSerial Port

Serial Port: Com1(RS485)

Serial Settings: Parity

Serial Settings: Baud Rate

Serial Settings: Data Bit

Serial Settings: Stop Bit


Document 800-06554 Rev C 3502/11

Installing and Configuring an Ethernet Connection

Note DVR ethernet control is currently unavailable. It will be available in future releases.

For a list of cable accessories see the Shipping Checklist on page 17, and for port connections and pin assignments, see UltraKey Touch Port Connections and Descriptions on page 18. The UltraKey Touch Controller runs TCP/IP keyboard protocol.

Step 1: Connect to the UltraKey Touch Using the Ethernet Port



3. Plug an RJ45 network cable from the network to the controller Ethernet port (see Figure 3-5).

4. Connect a DVR to the network. Refer to the applicable DVR Installation Guide for instructions.


Table 3-6 RJ45 Ethernet Pin Assignments

Port Pin Signal

RJ45 Ethernet 1 TX +

2 TX–

3 RX+

6 RX–

36


Figure 3-5 Ethernet Port Connections to DVR


Note If any mode other than DVR has been selected, then use the procedure in Step 2: Configure the UltraKey Touch for DVR Use on page 28 to select DVR mode. Otherwise skip to the next step.

Step 3: Configure the UltraKey Touch Ethernet Connection Settings

1. Press Alt > Clr to enter the System Configuration menu.

2. Rotate the slider or press the LCD up/down arrow keys to scroll through the options (standalone settings, serial port, network, language, slider update, cascade linkage, hardware test, about, and restore default).

3. Press Ent when you are at the System Configuration: Network menu.

Network Port Network Port Network Port

NETWORK

Network Cable

Network Cable

Network Cable

Master Slave 1 Slave 2

Network Port

Network Cable

UltraKey Touch

System Configuration Network


Document 800-06554 Rev C 3702/11

4. Press Slider_Down, the menu displays (one of):

5. Select the Network: Manual Setting menu and press Ent to confirm. Press the Slider_Up/Down or the LCD up/down arrow keys to setup the UltraKey Touch network parameters (IP Address, Gateway, NetMask and DNS):

a. Press the Slider_Up/Down or the LCD up/down arrow keys to scroll through the menu options and select IP Address. Press Ent. Using the numeric keypad, enter an IP address. Press Ent to save.

IPAddr Changed displays on the LCD menu. Press the Slider_Up/Down or the LCD up/down arrow keys to select Yes to save or No to cancel. Press Ent.

b. Press the Slider_Up/Down or the LCD up/down arrow keys to scroll through the menu options and select Gateway. Press Ent. Using the numeric keypad, enter a Gateway value, as required. Press Ent to save.

GW Changed displays on the LCD menu. Press the Slider_Up/Down or the LCD up/down arrow keys to select Yes to save or No to cancel. Press Ent.

c. Press the Slider_Up/Down or the LCD up/down arrow keys to scroll through the menu options and select NetMask. Press Ent. Using the numeric keypad, enter a NetMask value, as required. Press Ent to save.

NetMsk Changed displays on the LCD menu. Press the Slider_Up/Down or the LCD up/down arrow keys to select Yes to save or No to cancel. Press Ent.

d. Press the Slider_Up/Down or the LCD up/down arrow keys to scroll through the menu options and select DNS. Press Ent. Using the numeric keypad, enter a DNS value, as required. Press Ent to save.

DNS Changed displays on the LCD menu. Press the Slider_Up/Down or the LCD up/down arrow keys to select Yes to save or No to cancel. Press Ent.

6. If other changes are required from this menu (language, slider update, cascade linkage, hardware test, and about) see System Administration and Troubleshooting on page 65. Otherwise the installation and configuration is complete.

Keyboard Configuration for Cascade Linkage (Additional)

Note No entry is required in the baud rate field for Ethernet connected controllers.

Network: DHCP

Network: Manual Setting

Network: Show Net Infor

Network: IP Address

Network: GateWay

Network: NetMask

Network: DNS

38


Note The IP address of the master or slave keyboard is both referred to IP address in the Network menu.

1. Press Alt > Clr and scroll with the slider. The Cascade Linkage menu appears.

2. In cascade mode, you can set the keyboard status (such as master or slave), and the cascade IP address if its status is set as “slave”.

3. Press the Slider_Right to enter the Cascade Linkage menu.

There are two menu items: KBD Mode and IP Address.

• In the KBD Mode menu, the keyboard can be set as master or slave;

• In the IP Address menu, when the keyboard is in slave statues, you should set this cascade IP address to match the master’s IP address.

4. Press the Slider_Up/Down to scroll to KBD Mode and press Ent.

Set the keyboard as master or slave, and press Slider_Right or Ent to confirm.

5. For a slave keyboard, press the Slider_Left to return to the Cascade Linkage menu. Press the Slider_Up/Down until the IP Address menu displays, then set this cascade IP address to match the master’s IP address.

6. For a master keyboard, this cascade IP address is invalid. Set the master’s IP address in the Network menu.

7. Press Ent. Rotate the slider and use the numeric keypad to enter an IP address, as required.

Note The slave keyboard’s cascade IP address in the Cascade Linkage submenu must be the same as the master keyboard’s IP address in the Network submenu. The master keyboard’s cascade IP address in the Cascade Linkage submenu is invalid.

8. Press Ent to confirm.

System Configuration Cascade Linkage

Cascade Linkage: KBD Mode

Cascade Linkage: IP Address

Network: IP Address


Document 800-06554 Rev C 3902/11

Configuring UltraKey Touch Using the Web Browser (Optional)

Logging into the Web Browser

1. Input, navigate to, or copy and paste, the applicable IP address into your web browser:

• LAN connections: for example, http://192.168.1.9 (default).• Crossover cable connections - static address: http://192.168.1.9 (default).

2. Enter Administrator (case sensitive) in the User Name field.

3. Enter 1234 (default) in the Password field.

4. Click Login.

Figure 3-6 UltraKey Touch Login Page

Step 1: Configure UltraKey Touch to Standalone Mode

1. Log into the web browser (see Logging into the Web Browser on page 39).

2. From the top menu, click the Configuration tab (see Figure 3-7).

3. From the side menu, click the System Configurations tab.

4. Select Standalone from the System Mode drop-down list.

5. Select English from the System Language drop-down list.

6. Click Apply to save the configuration, Cancel to exit without saving, or Default to restore all factory default values.

40


Figure 3-7 System Configuration Tab

Step 2: Standalone Configuration for DVR Settings

1. From the side menu, click Standalone Configuration (see Figure 3-8).

2. Set the DVR type to be the same as the controlled DVR in the DVR Type drop-down list.

Select DVR type as Fusion, HRXD/HRSD, or HRDP.

3. Cascade Mode settings are used for the Cascade Linkage of keyboards.

a. Set the Ultrakey Touch as Master or Slave in the Mode drop-down list.

b. Set the IP of the Master UltraKey Touch in the Master IP Address drop-down list.

4. Set the Address, Name, and Protocol Type for the controlled PTZ in the PTZ window area.


Top menu

Side menu


Document 800-06554 Rev C 4102/11

Figure 3-8 Standalone Configuration for DVR Tab

Step 3A: Configure the Controller for a Serial Port Connection

1. From the side menu, click Serial Port Configuration (see Figure 3-9).

2. In the Serial Port1 Settings window area, select the appropriate value in the drop-down lists from each of the following fields:

• Baud Rate: 1200, 1800, 2400, 4800, 9600, 19200, 38400, or 57600 bps.• Parity: none, even, or odd.• Stop Bits: 1 or 2 bits.• Data Bits: 7 or 8 bits.• Serial Mode: RS232 or RS485.

3. If required, repeat step 2 for serial Com1/Com2 settings.


Side menu

42


Figure 3-9 Serial Port Configuration Tab

Step 3B: Configure the Controller IP for an Ethernet Connection

1. From the side menu, click IP Configuration (see Figure 3-10).

2. Enter IP Address, Subnet Mask, Gateway and DNS values in each of the fields.


Side menu


Document 800-06554 Rev C 4302/11

Figure 3-10 IP Configuration Tab

Controlling a FUSION DVR

Step 1: Connection

See Figure 3-3 on page 28, and Figure 3-4 on page 32.

Step 2: Select DVR Type

1. Press Alt + Clr to enter the Standalone Settings menu. See the menu tree (see Figure 3-2 on page 26) to select the DVR.

2. Press the Slider_Right and rotate the slider in the DVR TYPE menu. The following LCD screens are displayed.

3. Press the Slider_Right to select FUSION.

Side menu

Standalone Set: DVR

DVR Selection: FUSION

44


Step 3: DVR and Camera Connection

1. Press the Slider_Right to enter the Basic Set menu.

2. Press Ent. Rotate the slider to select the Camera (from 1 to 128). Press the Slider_Right to select the DVR as 1. Press the Slider_Left to save the configuration and exit the menu.

3. The keyboard can control 1, 4, 9, and 16-channel DVRs. For example, if a system has 33 cameras with:

• DVR 1, a 4-channel DVR connected to cameras 1 through 4 inclusive• DVR 2, a 4-channel DVR connected to cameras 5 through 8 inclusive• DVR 3, a 16-channel DVR connected to cameras 9 through 24 inclusive • DVR 4, a 9-channel DVR connected to cameras 25 through 33 inclusive

Then this system would be shown as in Table 3-7, below:

Operating a Fusion DVR

Basic Set:

DVR/CAM

CAM 1

DVR 1

Table 3-7 DVR Control CAM

CAM 1 ~ 4 DVR 1 4-channel DVR (DVR 1)




Table 3-8 Operating a Fusion DVR

You want to... Do this...

Select a DVR Press a number + DVR, or DVR + a number + Ent.

Use the Display function to program DVRs to rotate different Live or Search display grids.

For example: 4 camera (A), 4 camera (B), 4 camera (C), 4 camera (D), 9 camera (A), 9 camera (B), and 16 camera grid screens display.

Press Split on the keyboard to rotate to the DVR’s next grid display from the current grid display.

For example: if the current grid display is 4 camera (B) and you press Split, the DVR will change to the 4 camera (C) grid display.

OR

Press one or two of the number keys followed by Split to force the DVR to change into any kind of grid display (see the table below).

Press... To display in... Press... To display in...

4+1+Split 4A grid 9+1+Split 9A grid

4+2+Split 4B grid 9+2+Split 9B grid

4+3+Split 4C grid 1+6+Split 16 grid

4+4+Split 4D grid


Document 800-06554 Rev C 4502/11

Note For more information about PTZ operation for Fusion, see Step 2: Camera Selection on page 60 and Operating a PTZ Camera on page 60 (excluding PTZCALL).

Auto Sequence Press Seq to toggle Auto Sequence on a Fusion DVR.

Toggle Relay (alarm output) on a specified channel

Press the number key (less than 5), then Alarm.

Instant Record Press the number key, which represents a specific channel, followed by the Recycle key to toggle instant recording on that specified channel.

Switch to Full Screen Display Press Ent.

Select a Camera to Display Press number + Camera, or Camera + number + Ent, or number+Ent.

Reverse Play Press Backward to make a DVR play backwards while searching.

Stop Press Stop to halt video playing on a DVR.

Play Press Review to make a DVR play forwards while searching.

Adjust the forward or backward playback speed

Rotate your finger on the touch pad slider.

Zoom (if only one camera is selected in Search)

Press Set to adjust the zoom level from level 1 to level 5.

Search Date Press Search to display the Search menu for configuring the date, month and time for playback.

When the DVR is in search play mode and the channel to play has been set, users can press F1 to display the Search menu.

Navigate the Search date set menu See the table below for the keyboard operations for navigating the Search Date Set menu.

Display video of the previously selected camera

Press F3

Display the 4-camera split screen Press F4



Table 3-8 Operating a Fusion DVR


Press... To... Press... To...

F2 Up F8 Right

F7 Down Ent Confirm

F6 Left Clr Esc

46


Controlling an HRXD/HRSD DVR

Step 1: Connection


Step 2: Keyboard Setup for Connection

HRXD DVR setup is the same as the FUSION DVR setup except that you select HRXD (see Controlling a FUSION DVR on page 43).

Operating an HRXD DVR

DVR Selection: HRXD

Table 3-9 Operating an HRXD DVR


Select a DVR Press a number key + DVR, or DVR + number key + Ent.

Enter numbers for a password Press and hold the Alt key and then press the number keys.

Access the DVR menus Press F1 to open the password screen. Press and hold the Alt key, and enter the password. Then press Ent to access the DVR setup menu.

Navigate the DVR menus Use the following keys.

Cycle through the display settings Press Split to select the next display setting (in the cycle of 4x4, 3x3, 2x2 and PIP).

Press... To...

Slider_Up or F2 Move up

Slider_Down or F7 Move down

Slider_Left or F6 Move left

Slider_Right or F8 Move right

Ent Select an option.

F1 Exit the current menu. If the user presses F1 when in the Setup screen, the DVR exits the menus and returns to normal operation. Also used to enter the menu.


Document 800-06554 Rev C 4702/11

Cycle through the cameras that are displayed when viewing 2x2 and 3x3 displays

Use the Slider_Left/Right.

Set the screen layout of the multi-cameras, and select a camera to be displayed in the cameo

Press Ent, then Slider_Up, Slider_Down, Slider_Left or Slider_Right to select an active camera (highlight box displayed). Press a number key + Camera, or Camera + number + Ent, or number + Ent.

Start and stop a sequence Press Seq to put the DVR output into a sequence (the sequence depends on the current display mode and setup). If the key is pressed again, the sequence will stop (displaying the current step in the sequence).

Freeze and unfreeze the current display Press F10.

Select a camera Press number keys (to enter a valid camera number) + Camera, or Camera + number + Ent, or number + Ent. This will select a camera (identified by the number) for full-screen display on the DVR output. This also selects the associated DVR.

Reset an active alarm If an alarm is active, press Alarm to reset the DVR output (internal buzzer included).

Display the alarm event log If the DVR is in live monitoring mode (and no alarm is active), press Alarm to display the event log. Once the event log is open, navigate through it in the same way as described in Navigate the DVR menus, on page 46.

Note If user password is enabled on the DVR, then pressing Alarm will cause a user password screen to display. If a user password is required, then enter the password as described on page 46.

Display a camera on the spot monitor Press Monitor+number+Ent to choose a Spot Monitor, then number + Camera, or Camera + number + Ent, or number + Ent to select the camera that displays on that spot monitor.

Apply the spot monitor to a camera sequence Press Monitor+number+Ent to choose a Spot Monitor, and then Seq to apply the spot monitor to a camera sequence.

Instant record or panic record Press Recycle to enable/disable the Panic Recording on specified channel.

Open/close the Search menu Press Search to bring up the Search menu. Press the key again to exit the Search menu.

Play video Press Review to playback or pause the DVR video.

Switch between live monitoring and pause Press the Stop key to switch between the live monitoring and paused states.

Go to the next frame when the DVR is paused Rotate the slider clockwise to show the next frame.

Go to the previous frame when the DVR is paused

Rotate the slider counterclockwise to show the previous frame.

Fast forward the DVR playback Press Forward.

Rewind DVR playback Press Backward.



48


Note For more information about PTZ operation for HRXD, see Step 2: Camera Selection on page 60 and Operating a PTZ Camera on page 60 (excluding PTZCALL).

Controlling an HRDP DVR

Step 1: Connection


Step 2: Keyboard Setup for Connection

HRDP DVR setup is the same as the FUSION DVR setup except that you select HRDP (see Controlling a FUSION DVR on page 43).

Operating an HRDP DVR

Zoom in on an image on the screen Press Set.

To control PTZ domes Press Alt > Set to enable HJC4000 to control PTZ domes.



DVR Selection:

HRDP

Table 3-10 Operating an HRDP DVR


Select a DVR Press a number key + DVR, or DVR + number + Ent.

Note Common operations of the HRDP and Fusion DVRs are not listed here.

Cycle through different displays in Live mode Press the Display button to cycle through the different displays in live mode. You cannot enter numbered inputs.

Enter the DVR Setup menu Press the Monitor button.


Document 800-06554 Rev C 4902/11

Auto Sequence Press Seq to cycle through the remaining channels within the display mode or rotate the display configuration. For both live viewing and searching, in PTZ mode, Seq can be used to enter PRESET mode.

Configure Alarm Out settings Not supported.

Instant record Press Recycle to start instant recording of all channels.

Display a selected camera in full screen mode Press a number key + Camera, or Camera + number + Ent, or number + Ent.

Toggle between Live view and Search Press Search.

Enter FOCUS mode while in PTZ mode Press Search.

Play videos in reverse Press F6 or Reverse. You can continuously press Reverse to change the playback speed.

Stop playback Not supported.

Play recorded videos Press F8 or Forward. You can continuously press Forward to change the playback speed.

Zoom in on video Image Zoom function is not supported in Live or Search mode. But when an HRDP is in PTZ mode, press the Set key to enter ZOOM mode.

Enter Backup mode while in Live or Search mode

Press Set.

Enter the express search mode Press F1 while in Search mode.

Navigate the menu See the table below for the keyboard operations for navigating menus.

Cycle through different displays in Live mode Press F3, F4, F5, F9.

Start Panorama Search in playback mode Press F2.

Start Smart Search in playback mode Press F7.

Enter PTZ mode Press F10.

Exit PTZ mode Press Clr.




F2 Up F8 Right

F7 Down Ent Confirm

F6 Left Clr Esc

50


Note The Iris, Focus, and Preset Store (View+Num+Set) keys are not supported. The Preset Call (View+Num+Ent or Num+View) key is supported.

Joystick Controls

To control PTZ cameras Use the joystick or see the table below for the keyboard operations for contolling PTZ domes.

Note You cannot use the keyboard to stop panning or tilting.




F2 Tilt up F6 Pan left

F7 Tilt down F8 Pan right

Table 3-11 Joystick Controls

Control Function

Joystick up/down Navigation mode: move the cursor up/down. Playback mode: start a Panorama/Smart search. PTZ mode: same functions as for a Fusion DVR.

Joystick left/right Navigation mode: move the cursor left/right.Playback mode: play recorded videos forwards or reversed.PTZ mode: same functions as for a Fusion DVR.

Joystick zoom in Live mode: starts playback of the latest recording.PTZ mode: adjust zoom and focus on a PTZ channel.Playback mode: cycle the playback speed from 1X to 8X.Playback-pause mode: cycle the playback speed from 1/2X to 1/8X.

Joystick zoom out Live mode: switches to PTZ mode. PTZ mode: adjust zoom and focus on a PTZ channel. Playback mode: cycle the reverse playback speed from 1X to 8X. Playback-pause mode: cycle the reverse playback speed from 1/2X to 1/8X.

Document 800-06554 Rev C 5102/11

4

Installing UltraKey Touch with PTZ


• Navigating LCD Configuration Menus on page 51• Installing and Configuring a Serial Connection on page 52• Configuring UltraKey Touch Using the Web Browser (Optional) on page 56• Controlling PTZs on page 59

Note For all installations, refer to the applicable PTZ installation or user guides for more information.

This section explains how to connect the UltraKey Touch controller to a PTZ camera and how to enter the basic configuration settings specific to PTZs. For other user configurations see the table of contents.

Navigating LCD Configuration Menus

Note See Using the UltraKey Touch to Navigate the LCD Menus on page 21 for detailed instructions for other ways to navigate or System Administration Using the Controller LCD on page 65 for configuration menu navigation.

52


Figure 4-1 PTZ Configuration Menu Tree

Installing and Configuring a Serial Connection

Step 1: Connect to the UltraKey Touch Serial Port

Note For a list of accessories see Shipping Checklist on page 17 and for port connections see UltraKey Touch Port Connections and Descriptions on page 18.

Note COM1 (RS485) are configured using the System Configuration menu. See Table 4-1 below. For connection between Ultrakey Touch and PTZ, refer to Figure 4-2. Certain settings should be done before using the direct control of a PTZ with Ultrakey Touch.

Table 4-1 Serial Port COM1 Pin Assignments


COM1 RS485 1 T/R +

2 T/R –


Data Bit

NetworkSerial PortStandalone

Settings

Protocol / Address / Name

PTZ DVR

Baud Rate

Parity Stop Bit

IP Address

COM1 (RS485) Show Net Infor Manual Settings DHCP

Serial SettingsPTZ Settings

Gateway

NetMask

DNS


Document 800-06554 Rev C 5302/11

RS485 Serial Port Connecting to a PTZ using the RJ45 Box:

1. Select the applicable adapter plug and insert it into the AC adapter. Push to click it into place. See Figure 4-2.

2. Connect an RJ45 network cable from the RJ45 Box port to the controller serial port.

3. Connect the pin (RS485+, RS485–) of the RJ45 Box to a PTZ using an appropriate wire.

Note To setup Cascade Linkage for UltraKey Touch, see Keyboard Configuration for Cascade Linkage (Additional) on page 37.

Figure 4-2 RS485 Serial Port Connection PTZ by RJ45 Box

Serial Port (RS485)

4

3

2

1

5

6

7

8

RJ45 box

Network cable

RS485

UltraKey Touch


NETWORK

Master Slave 1

Network cable

Network cable

Table 4-2 RJ45 Box Pin Assignments

Pin Signal

1 RS485+

2 RS485–

4 RS232 RXD

5 GND

6 RS232 TXD

54


Step 2: Configure the Controller for PTZ

Note In the Standalone main menu, press Ent, and rotate the slider to enter PTZ settings or press PTZ. You can set the PTZ Name, Address, and Protocol.

1. Install and connect the controller to a power source, if it is not already connected.The UltraKey Touch LCD displays.

2. Press the Login key and enter the password: 1234. Press Ent to confirm.

3. From the home screen, press Alt > Clr to enter the System Configuration menu.

4. Scroll to and select Standalone Settings. Press Slider_Right or Ent to enter the Standalone Set menu.

5. Rotate the slider to select the PTZ, press Slider_Right to enter PTZ settings.

6. Press Slider_Down or LCD arrow key up/down, and the following figure is displayed on LCD screen:

a. Use the Slider_Up/Down keys to scroll to different controller protocols. Press Ent to save.

b. Use the Slider_Up/Down keys to scroll to change the name of the controller. Press Ent to save.

c. Use the Slider_Up/Down keys to scroll to an address between 1 and 128 to assign to the controller. Press Ent to save.

Return to the home screen.

If the keyboard is in DVR mode after changing to PTZ settings, then the home screen displays this message:Select Yes or No to change the work mode of the keyboard.

If the keyboard is in PTZ mode after changing to PTZ settings, then the home screen does not display that message.

Step 3: Configure Serial Port of the Controller

1. Press Alt > Clr to enter the System Configuration top menu.


CAM 001ST User2



System ConfigurationStandalone Setting

Standalone Set:PTZ

PTZ Setting:Protocol

PTZ Setting:Name

PTZ Setting:Address

Change to PTZ mode?Yes


Document 800-06554 Rev C 5502/11

2. Press the Slider_Up/Down or LCD up/down arrow key to scroll through the options (standalone settings, serial port, network, language, slider update, cascade linkage, hardware test, about, and restore default).

3. When you are at the System Configuration: Serial Port menu, press Ent.

4. Use the Slider_up/down to select Com1(RS485). Set Com1 according to the table below.

5. Press Slider_Up/Down keys or LCD up/down arrow key to select COM1. Press Ent, the Serial Setting menu displays where you can set these COM1 settings: parity, baud rate, data bit and stop bit.

a. Press LCD up/down arrow key to select Parity. Press Ent and use the Slider_Up/Down keys to select None, Odd, or Even. Press Ent to save.

b. Press LCD up/down arrow key to select BaudRate. Press Ent and use Slider_Up/Down keys to select 1200, 1800, 2400, 4800, 9600, 19200, 38400, or 57600. Press Ent to save.

c. Press LCD up/down arrow key to select DataBit. Press Ent and use Slider_Up/Down to select 7 bit or 8 bit. Press Ent to save.

d. Press LCD up/down arrow key to select StopBit. Press Ent and use Slider_Up/Down to select 1 bit or 2 bit. Press Ent to save.

6. If other changes are required from this menu (language, slider update, cascade linkage, hardware test, about, restore default), see System Administration and Troubleshooting on page 65. Otherwise the installation and configuration is complete.

7. After finishing keyboard setup, press Slider_Left to return to the main menu.

8. To select a camera for control, press a number (1–128) + Camera, or Camera + number + Ent, or number + Ent.

System Configuration:Serial Port

Serial PortCom1(RS485)

Type RS485

Baud Rate 9600

Parity None

DataBit 8

StopBit 1

Serial Setting:

Parity

Serial Setting:

Baud Rate

Serial Setting:

Data Bit

Serial Setting:

Stop Bit

56


Configuring UltraKey Touch Using the Web Browser (Optional)


1. If not already done, navigate to, or copy and paste, the applicable IP address into your web browser:

• LAN connections: for example, the default IP is http://192.168.1.9.• Crossover cable connections - static address: http://192.168.1.9.

2. Enter Administrator (case sensitive) in the User Name field (see Figure 4-3).

3. Enter 1234 (default) in the Password field.

4. Click Login.

Figure 4-3 UltraKey Touch Login page

Step 1: Configure UltraKey Touch to System Configurations

1. Log into the web browser.

2. From the top menu, click the Configuration tab.

3. From the side menu, click the System Configurations tab.

4. From the System Mode drop-down list, select Standalone (see Figure 4-4).

5. From the System Language drop-down list, select English.

6. Click Apply to save the configuration, Cancel to exit without saving or Default to restore all factory default values.


Document 800-06554 Rev C 5702/11

Figure 4-4 System Configuration Tab

Step 2: Standalone Configuration for PTZ Settings

1. From the side menu, click Standalone Configuration (see Figure 4-5).

2. Under DVR Setting drop-down list, set DVR type as same as the controlled DVR.

3. Under Cascade Mode, the settings are used for cascading linkage of keyboards.

a. Under Mode drop-down list, select Master or Slave for Ultrakey Touch.

b. Under Master IP Address drop-down list, set the IP of the Master UltraKey Touch.

4. Under PTZ, set the address, name, and protocol for the controlled PTZ.

5. Under Protocol Type drop-down list, select Diamond, PelcoD, PelcoP, VCL, IntelliBUS protocol consistant with the controlled Ultrakey Touch.


58


Figure 4-5 Standalone Configuration for PTZ Tab

Step 3: Configure the Controller for a Serial Port Connection

1. From the side menu, click Serial Port Configuration (see Figure 4-6).

2. Under Serial Com1 Settings, select the following from each drop-down list, as required:

• Baud Rate: 1200, 1800, 2400, 4800, 9600, 19200, 38400, or 57600 bps• Parity: none, even or odd• Stop Bits: 1 or 2 bits• Data Bits: 7 or 8 bits• Serial Mode: RS485

3. Click Apply to save the configuration, Cancel to exit without saving or Default to restore all factory default values.


Document 800-06554 Rev C 5902/11

Figure 4-6 Serial Port Configuration Tab

Controlling PTZs

Step 1: Keyboard Setup

For a connection between Ultrakey Touch and a PTZ, see Figure 4-2.

Certain settings should be done before using the direct control of PTZ with Ultrakey Touch.

1. Set COM1 (RS485) according to the table below:

Type RS485

BaudRate 9600

Parity None

DataBit 8

StopBit 1

60


2. See the PTZ configuration menu tree ( Figure 4-1 on page 52). Select Standalone Settings, press Ent, and rotate the slider to enter PTZ Settings, or press PTZ. You can set the PTZ Name, Address, and Protocol.

Note The UltraKey Touch supports five PTZ Protocols: Pelco P, Pelco D, Diamond, VCL, and Intellibus. You must set the PTZ’s Protocol to be consistant with the controlled PTZ.

Step 2: Camera Selection

1. Return to the main menu of standalone mode after finishing keyboard setup

2. Enter a camera number (1–128) + Camera, or Camera + number + Ent, or number + Ent to select a camera for controlling.

Operating a PTZ Camera

PTZ call for Diamond Protocol

The PTZ call is used in Diamond protocol and Intellibus protocol to control certain features of the PTZ camera.

For Diamond protocol, press PTZ call and the following figures are displayed in sequence by rotating the slider. Press Ent to select. Press Clr to exit from the Dome OSD display.

1. PTZ - Auto IrisPress Ent to send auto iris command.

Standalone Set:

PTZ

Table 4-3 Operations for a PTZ Camera


Control a PTZ camera Use the joystick to control (pan and tilt) the camera. Move the joystick up/down for tilt functions and left/right for pan functions.

Zoom in/out Rotate the joystick clockwise/counter-clockwise.

Adjust the iris Press Iris (+) and Iris (–).

Manually focus Press Focus (+) or Focus (–).

Program a preset Press View + number + Set.

Run a preset Press View + number + Ent, or number + View.

<Cam001>

Auto Iris


Document 800-06554 Rev C 6102/11

2. PTZ - TourPress Ent, enter a tour number, and then press Ent again. Press the LCD Up/Down arrow keys to toggle between selections in the Program/Run/Cancel/Delete function submenu. Press Ent to confirm the selection.

3. PTZ - Preshot MenuThis represents the preset programming function. Press Ent to enter the Sel Character menu on the keyboard LCD. Press the LCD Right/Left arrow keys to skip character pages and select the character by pressing the button below the character. You can also press the NUM keys on the keyboard to select the num value. Press Alt + Clr to return to the previous menu.

4. PTZ - Sector MenuThis represents the Sector programming function.The Sel Character menu operation is the same as Preshot Menu.

5. PTZ - Main MenuPress Ent to enter the PTZ OSD menu.

The Sel Character menu operation is just the same as Preshot Menu.

Press a number on the keyboard to select a submenu, then press another number on the keyboard to enter the lower submenu.

6. PTZ - List PreshotPress the Slider_up/down to scan to different pages.

7. PTZ - List VectorPress the Slider_up/down to scan to different pages.

8. PTZ - List SectorPress the Slider_up/down to scan to different pages.

9. PTZ - VectorThis represents the Preset Tour programming function.The Sel Character menu operation is just the same as Preshot Menu.

10. PTZ - VectorScan ContPress Ent to run a continuous Preset Tour. Input a tour number, and then press Ent to confirm.

11. PTZ - VectorScan OncePress Ent to run a single Preset Tour. Input a tour number, and then press Ent to confirm.

Note For ACUIX PTZs, Diamond protocol does not support Baud Rates of 1200 and 2400. All other Baud Rates are supported.

<Cam001>

Tour

<Cam001>

Preshot Menu

Sel Character

<A B C>

<Cam001>

Sector Menu

<Cam001>

Main Menu

<Cam001>

List Preshot

<Cam001>

List Vector

<Cam001>

List Sector

<Cam001>

Vector

<Cam001>

VectorScan Cont

<Cam001>

VectorScan Once

62


PTZ call for Intellibus Protocol

Familiarize yourself with these basic operations before you start configuring the menus:

• Press Ent to enter the setup menu and the submenus displayed on the LCD screen. Press the number on the keyboard to select a submenu, then press Ent to confirm the selection.

• Press Clr to exit from the Dome OSD display.• Press Alt + Clr to return to the main menu. • Press numbers on keyboard to input numbers and press F6/F8 to change the

coordinates for inputting the numbers.• Press PTZ call to select the Setup menu and then press Ent. The Sel Character

menu displays. Press the LCD Left/Right arrow keys to skip character pages and select the character by pressing the button below the character.

• Press PTZ call to select the List menu (Sector List, VectorScan List, VectorScan View, and Preset List) and then press Ent. The List menus are listed on the LCD screen. Press the Slider_Up/Down to scan to different pages.

For Intellibus protocol, press PTZ call and the following options are displayed in sequence by rotating the slider. Press Slider_Right or Ent to select an option.

1. PTZ – Setup

Press Ent. The Sel Character menu displays on the keyboard LCD.

Press a number on the keyboard to select a submenu on the LCD screen, then press Ent to confirm the selection.

2. PTZ – Sector List

Press PTZ call and Sector List is displayed on the LCD screen. Press the Slider_Up/Down to scan to different pages.

3. PTZ – Sector Prog

Press PTZ call, select Sector Prog and press Ent. You can edit, program or delete sectors from this menu.

4. PTZ – VectorScan List

Press PTZ call and VectorScan List is displayed on the LCD screen. Press Ent to confirm the selection. Press the Slider_Up/Down to scan to different pages.

5. PTZ – VectorScan Prog

Program VectorScan: Press Tour + number + Set on the keyboard.

Run VectorScan: Press number + Tour, or Tour + number + Ent.

You can also edit or delete presets in the Setup menu. Press PTZ call on the keyboard to select the Setup menu. Press Ent to confirm. For example, press number 3 to enter the third menu and then 7 to enter the submenu. Press Ent to confirm.

6. PTZ – VectorScan View

Press PTZ call and VectorScan View is displayed on the LCD screen. Press Ent to confirm the selection. Press the Slider_Up/Down to scan to different pages.

<Cam 001>

Setup

Sel Character

<A B C>

<Cam 001>

Sector List

<Cam 001>

Sector Prog

<Cam 001>

VectorScan List

<Cam 001>

VectorScan Prog

<Cam 001>

VectorScan View


Document 800-06554 Rev C 6302/11

7. PTZ – VectorScan Once

Press PTZ call, select the VectorScan Once submenu and press Ent.

8. PTZ – Preset List

Press PTZ call and Preset List is displayed on the LCD screen. Press Ent to confirm the selection. Press the Slider_Up/Down to scan to different pages.

9. PTZ – Preset Prog

Program Preset: Press View + number + Set.

Run Preset: Press View + number + Ent, or number + View.

You can also edit or delete presets in the Setup menu. Press PTZ call on the keyboard to select the Setup menu. Press Ent to confirm. Press the number of the preset you want to select. Press Ent to confirm.

Note For ACUIX PTZs, Intellibus protocol only supports three Baud Rates: 9600, 19200, and 38400. Also, Intellibus protocol does not support Cascade Linkage.

<Cam 001>

VectorScan Once

<Cam 001>

Preset List

<Cam 001>

Preset Prog

64


Document 800-06554 Rev C 6502/11

5

System Administration and Troubleshooting


• System Administration Using the Controller LCD on page 65• System Administration Using the Web Browser on page 67

System Administration Using the Controller LCD

To navigate all configuration LCD menus, see the System Configuration Menu Tree on page 75.

Logging in and Navigating to the System Configuration Menu

1. If not already done, install and connect the controller to a power source.

The UltraKey Touch LCD displays.

2. Enter the PIN password 1234.

3. From the home screen, press Alt > Clr to enter the System Configuration.

Setting the Screen Language

1. Log into the controller.

2. From the System Configuration menu, press Slider_Up/Down continuously to enter the language setup menu, or rotate the slider until System Configuration: Language appears. Press Ent.

3. Press Slider_Up/Down keys to scroll through the options and select one. Press Ent to save.

CAM 001 DVR 1ST Logout


Language

66


Restore Default


2. From the System Configuration menu, press Slider_Up/Down to scroll to Restore default.

3. Press Ent to confirm whether or not to restore to factory defaults.

Updating the Touch Pad Firmware


2. From the System Configuration menu, press Slider_Up/Down to scroll to Slider Update. Press Ent.

The message Update Confirm? displays.

3. Press the LCD up arrow key to select Yes or No.

• Select Yes and press Ent to upgrade the firmware.• Select No and press Ent to cancel.

If you select Yes, the message Slider Firmware: Download displays, followed by Download: OK.

4. Press Ent to exit the menu.

Viewing the Firmware Version


2. From the System Configuration menu, press Slider_Up/Down to scroll to About. Press Ent.The LCD scrolls to display the firmware version.

3. Press any key to return to the previous menu.

Testing the Hardware


2. From the System Configuration menu, press Slider_Up/Down to scroll to Hardware Test. Press Ent.


Restore default

System ConfigurationSlider Update

Update confirm?

Yes

Slider Firmware:

Download: ok

System ConfigurationAbout

System ConfigurationHardware test


Document 800-06554 Rev C 6702/11

3. Press Slider_Up/Down keys and press Ent to select one or all of the following test options:

• Key: When you press a key, the key value and its state is displayed on LCD.

• Joystick: When you move the joystick, values which present the PTZ (pan, tilt, zoom) positions of the joystick are displayed on the LCD.

• SerialPort: Confirms that the controller serial port is functioning.

• Slider: When you rotate the touch pad, specific values are displayed on the LCD.

4. Press Alt > Clr to exit from these test menus.

System Administration Using the Web Browser


1. If not already done, navigate to, or copy and paste, the applicable IP address into your web browser:

• LAN connections: for example, http://192.168.1.9.• Crossover cable connections - static address: http://192.168.1.9, and it must be

consistent with the UltraKey Touch IP address (refer to network configuration).• In the User Name field enter Administrator (case sensitive).

2. In the Password field enter 1234 (default).

3. Click Login.

Upgrading the UltraKey Touch Firmware


2. From the top menu, click the Upgrade tab.

The warning message Please make sure the network connection is connected during system upgrading displays (see Figure 5-1).

3. Click OK. The Software Upgrade menu opens.

4. Select a Folder from the drop-down list: Application, Kernel, or File System.

5. In the Select File field, click Browse. Navigate to the file and click OK.

6. Click Send to start the upgrade process.

Device Test:Key

Device Test:Joystick

Device Test:SerialPort

Device Test:Slider

68


The Upgrade Status window opens. Messages display to indicate when old files are being erased and new files are being copied.

When the process is complete, the message Upgrade success displays and the system reboots.

Figure 5-1 Software Upgrade Warning Message

Rebooting UltraKey Touch


2. From the top menu, click the System Reboot tab.

The Reboot System window opens.

3. Click Reboot to continue, click another tab, or click Logout to exit without rebooting.

Changing the UltraKey Touch Password


2. In the upper right corner, click Change Password (see Figure 5-2).

3. In the Old Password field, enter the current password.

4. In the New Password field, enter a new password.

5. Enter the new password in the Confirm New Password field.

6. Click Apply to set the new password or Cancel to exit without changing it.


Document 800-06554 Rev C 6902/11

Figure 5-2 Change Password Page

70


Document 800-06554 Rev C 7102/11

A

DVR Operation Commands

Fusion Operation Commands

Table A-1 Fusion DVR Operations

Keys... Function...

Number keys Press a number key + DVR, or DVR + number + Ent to select a DVR to control.

Press 4+1 + Split to display in 4A grid

Press 4+2 + Split to display in 4B grid

Press 4+3 + Split to display in 4C grid

Press 4+4 + Split to display in 4D grid

Press 9+1 + Split to display in 9A grid

Press 9+2 + Split to display in 9B grid

Press 1+6 + Split to display in 16 grid

Seq Press to toggle Auto Sequence on Fusion DVR.

Alarm Press the number key (less than 5 ) followed by Alarm to toggle Relay (Alarm output) on specified channel.

Recycle Press the number key which presents for the specified channel, then Recycle to toggle Instant Record on specified channel.

Camera Press the number key + Camera, or Camera + number + Ent to show the specified camera.

Live/Search Toggles Fusion Live/Search Display.

In PTZ mode, Live/Search can be used to enter FOCUS mode.

Reverse Press to play recorded videos in reverse in Search mode.

Stop Stops video playback.

Play Play video forwards in Search mode.

Zoom If only one camera is selected in search, press Set to adjust the zoom level from level 1 to level 5.

72


HRXD/HRSD Operation Commands

Touch Pad Slider Adjusts the forward and backward playback speeds.

Search Press to display the Search menu for configuring the date, month, and time for playback.

F2, F7, F6, F8, Ent, Clr Up, down, left, right, confirm, esc

F3 Press F3 to display video of the previously selected camera.

F4 Press F4 to display the 4-split screen.



Table A-2 HRXD/HRSD Operations

Keys... Function...

Number keys Press a number key, then DVR to select a DVR to control.

Number Entry For entering passwords.

F1 Press to open the password screen.

Alt Press and hold, while in the DVR menu, then enter the password.

And then press Ent to access the DVR set-up menu.

Slider_Up/F2 Press while in the DVR menu to move up.

Slider_Down/F7 Press while in the DVR menu to move down.

Slider_Left/F6 Press while in the DVR menu to move left.

Slider_Right/F8 Press while in the DVR menu to move right.

Ent Press while in the DVR menu to select an option.

F1 Press while in the DVR menu to exit the current menu.

Split Press to select the next display setting (in the cycle of ‘4x4’, ‘3x3’, ‘2x2’ and ‘PIP’).

Seq Press Monitor+number+Ent to choose a Spot Monitor, then press Seq to apply that spot monitor to a camera sequence.

F10 Press to freeze the current display.

Camera Press number + Camera, or Camera + number + Ent, to select that number camera.

DVR Press number + DVR, or DVR + number +Ent to select a DVR.

Table A-1 Fusion DVR Operations (cont’d)

Keys... Function...


Document 800-06554 Rev C 7302/11

HRDP Operation Commands

Alarm If an alarm is active, press Alarm to reset the output of DVR (including internal buzzer).

If the DVR is in live monitoring mode (and no alarm is active), press Alarm to display the event log.

Monitor To display a camera on the spot monitor, press Monitor+number+Ent to select a Spot Monitor, then number + Camera, or Camera + number + Ent, or number + Ent.

Recycle Press to enable/disable the PANIC RECORD on specified channel.

Live/Search Press to bring up the Search menu. Press again to exit the Search menu.

Review Press to playback or pause the DVR video.

Stop Press to switch between live monitor state and pause state.

Next Frame Rotate the slider clockwise to show the next frame when the DVR is in pause state.

Previous Frame Rotate the slider counter-clockwise to show the previous frame when the DVR is in pause state.

Forward Press to make DVR playback quickly.

Backward Press to make DVR rewind quickly.

Set Press to zoom the image on the screen.

PTZ Control Press Alt+Set to enable HJC4000 to control PTZ of HRXD/HRSD.

Table A-3 HRDP Operations

Keys... Function...

Number keys Press a number key + DVR, or DVR + number + Ent to select a DVR to control.

Display Cannot take number inputs. Press Display in Live mode to cycle through the different displays.

Seq In Live and Search modes, press Seq to Auto Sequence (rotate) through the remaining channels within the display mode, or to rotate the display configuration.

In PTZ mode, Seq can be used to enter PRESET mode.

Alarm out Not supported.

Instant record Press Recycle to start instant recording of all channels.

Camera Press the number key + Camera, or Camera + number + Ent, or number + Ent to show the specified camera in full screen.

Live/Search Toggles Fusion Live/Search Display.

In PTZ mode, Live/Search can be used to enter FOCUS mode.

Table A-2 HRXD/HRSD Operations (cont’d)

Keys... Function...

74


Monitor Press to enter the DVR Setup menu.

Reverse/F6 Press to play recorded videos in reverse. Continuously pressing Reverse will change the playback speed.

Stop Not supported.

Forward/F8 Press to play recorded videos. Continuously pressing Forward will change the playback speed.

Zoom Not supported in Search mode, but entering backup mode.

In PTZ mode, Zoom can be used to enter ZOOM mode.

F1 key in search Press to enter Express Search mode.

F2,F7,F6,F8,Ent,Clr Up, down, left, right, confirm, esc

F3,F4,F5,F6, Same as Display button functions.

F2 Press to start Panorama Search when in playback mode.

F7 Press to start Smart Search when in playback mode.

F10 Press to enter PTZ mode.

Clr Press to exit PTZ mode.

F2,F7,F6,F8 Press to tilt a PTZ camera up/down and pan a PTZ camera left/right. There is no key to stop PTZ action.

Note You can also use the joystick to control a PTZ camera.

Iris (Iris key) Not supported.

Focus (Focus key) Not supported.

Preset call (View key) Supported.

Preset store (View key) Not supported.

Joystick_Up/Down Navigation mode: move the cursor up / down. Playback mode: start a Panorama/Smart search. PTZ mode: same controls as a Fusion DVR.

Joystick_Left/Right Navigation mode: move the cursor left / right.Playback mode: play recorded videos forwards or reversed. PTZ mode: same control as a Fusion DVR.

Joystick_zoom in Live mode: joystick zoom in starts playback of the most recently recorded video. PTZ mode: adjust zoom and focus on a PTZ channel. Playback mode: cycle the playback speed from 1X to 8X.Playback-pause mode: cycle the playback speed from 1/2X to 1/8X.

Joystick_zoom out Live mode: joystick zoom out switches to PTZ mode. PTZ mode: adjust zoom and focus on a PTZ channel. Playback mode: cycle the reverse playback speed from 1X to 8X. Playback-pause mode: cycle the reverse playback speed from 1/2X to 1/8X.

Table A-3 HRDP Operations (cont’d)

Keys... Function...


Document 800-06554 Rev C 7502/11

System Configuration Menu Tree

Figure A-1 System Configuration LCD Menu Tree - All Modes


Data Bit

Network

Slider Update

Standalone Settings

KBD Mode

DVR

PTZ

Baud Rate

Parity

Stop Bit

IP AddressShow Net Infor

Manual Settings

DHCP

Serial Settings

Slider

Gateway

NetMask

DNS

Hardware Test

Cascade Linkage

Serial Port

About

Language

Restore Default

IP Address

Com1 (RS485) / Com2 (RS232)

Standalone Set

English

Protocol / Address / Name

HRDP / FUSION / HRXD

PORT SELECT

DVR / CAM

DVR Selection

Serial Port

Key

Joystick

Basic Set

RS232 / RS485

76


Honeywell Systems (Head Office)2700 Blankenbaker Pkwy, Suite 150Louisville, KY 40299, USAwww.honeywellvideo.com +1.800.796.2288

Honeywell Systems Europe/South AfricaAston Fields Road, Whitehouse Industrial EstateRuncorn, Cheshire, WA7 3DL, UKwww.honeywell.com/security/uk +44.01928.754028

Honeywell Systems Caribbean/Latin America9315 NW 112th Ave.Miami, FL 33178, USAwww.honeywellvideo.com +1.305.805.8188

Honeywell Systems PacificLevel 3, 2 Richardson PlaceNorth Ryde, NSW 2113, Australiawww.honeywellsecurity.com.au +61.2.9353.7000

Honeywell Systems Asia35F Tower A, City Center, 100 Zun Yi RoadShanghai 200051, Chinawww.asia.security.honeywell.com +86 21.5257.4568

Honeywell Systems Middle East/N. AfricaPost Office Box 18530LOB Building 08, Office 199Jebel Ali, Dubai, United Arab Emirateswww.honeywell.com/security/me +971.04.881.5506

Honeywell Systems Northern EuropeAmpèrestraat 411446 TR Purmerend, The Netherlandswww.honeywell.com/security/nl +31.299.410.200

Honeywell Systems DeutschlandJohannes-Mauthe-Straße 14D-72458 Albstadt, Germanywww.honeywell.com/security/de +49.74 31.8 01.0

Honeywell Systems FranceImmeuble LavoisierParc de Haute Technologie3-7 rue Georges Besse92160 Antony, Francewww.honeywell.com/security/fr +33.(0).1.40.96.20.50

Honeywell Systems Italia SpAVia della Resistenza 53/5920090 BuccinascoMilan, Italywww.honeywell.com/security/it +39.02.4888.051

Honeywell Systems EspañaAvenida de Italia, n° 7P.I. - C.T.C. Coslada28820 Coslada, Madrid, Spainwww.honeywell.com/security/es +34.902.667.800

© 2011 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell. The information in this publication is believed to be accurate in all respects. However, Honeywell cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice. Revisions or new editions to this publication may be issued to incorporate such changes.

Document 800-06554 – Rev C – 02/11

www.honeywellvideo.com+1.800.796.CCTV (North America only)

[email protected]

http://www.honeywellvideo.com

http://www.honeywellsecurity.com.au

http://www.honeywell.com/security/uk

http://www.honeywell.com/security/fr

http://www.honeywell.com/security/it

http://www.honeywell.com/security/es

http://www.honeywell.com/security/nl

http://www.asia.security.honeywell.com


http://www.honeywell.com/security/de

http://www.honeywell.com/security/me


installation and user guide - honeywell

Documents