inside of rh & rhr door outside of rh & rhr door...
TRANSCRIPT
MORTISE LOCK HORIZONTAL CENTRELINE
WOOD DOOR PREPARATION FOR DM SERIES MORTISE LOCK DOOR PREPARATION TABLE
NOTES:
INSIDE OF RH & RHR DOOR OUTSIDE OF RH & RHR DOOR
UP
DOOREDGE
DOOREDGE
FINISHED FLOOR LEVEL
QTY 2 THROUGH HOLES FORESCUTCHEON TRIM ONLY
(IF APPLICABLE-REFER TO TABLE)
MORTISE LOCK BODY CAVITY
2 3/4”
1 3/4” DOOR THICKNESS
EXTENSION KITS REQUIRED FOR THICKER DOORS
THROUGH HOLEFOR KNOB/LEVER
HOLE ON INSIDE DOOR SKIN ONLY, FOR THUMBTURN
(IF APPLICABLE- REFER TO TABLE)
KN
OB
/LEV
ER H
OLE
CY
LIN
DER
HO
LE
EMER
GEN
CY
KEY
HO
LE
KN
OB
/LEV
ER H
OLE
CY
LIN
DER
HO
LE
THU
MB
-TU
RN
HO
LE
DM42 PRIVACY
DM45 ENTRANCE
DM50 OFFICE
DM56 DORMITORY
DM70 CLASSROOM
DM80 STOREROOM
DM84 STOREROOM WITH DEADBOLT
DM172 DUMMY BACK TO BACK
BACKSETVERTICAL LINE
HALF OF DOOR THICKNESS
QTY 2 THROUGH HOLES FORESCUTCHEON TRIM ONLY(IF APPLICABLE)
MORTISE LOCK CAVITY
2 3/4”
THROUGH HOLEFOR KNOB/LEVER
HOLE ON OUTSIDE DOOR SKIN ONLY FOR PRIVACY EMERGENCY KEY (IF APLICABLE - REFER TO TABLE)
HOLE ON OUTSIDE DOOR SKIN ONLY FOR MORTISE CYLINDER (IF APPLICABLE - REFER TO TABLE)
CAN-DM-DP-W
DM-DPW-R7-2016-01
TITLE:
TOLERANCES: SEE SHEET 2
www.dorex.comDOREX
REVISION: 7
DATE: 15 OCT 2007
REVISION DATE: 06 JAN. 2016
DOCUMENT NO:
SHEET 1 OF 2
LOCK FUNCTION
DM SERIES
B C C
DM10 PASSAGE
BA
TRIM
OUTSIDE INSIDE
DOOR VERTICALCENTRELINE
DRAWINGS ARE NOT AT FULL SCALE. DO NOT USE AS TEMPLATE.CAUTION:
40-9/16” REF
C
A CA
CC
B
DISCLAIMER:The supplied door preparation information is based on latest product configuration and within industry dimensional tolerances. Dorex reserves the right to change or update the door preparation data at any time. It is the responsiblity of the user to ensure that the latest document revision is used by contacting his Dorex representative.
BACKSETVERTICAL LINE
1. Supplied door preparation is suitable for wood, laminate flush faced and wood stile doors 1 3/4” (44.5 mm) thick.2. Appropriate reinforcement is recommended for hollow metal doors to support the lock body in the center of the door edge cavity, and to prevent the door from compressing when lock trim is tightened (consult your sales representative).3. Before drilling or boring holes, consult the Door Preparation Table to determine the holes that need to be bored or drilled for the appropriate door handing and lock function.4. For detailed dimensions see sheet 2.5. Door cavity for lock body must be parallel to the door surface within ± 0.03”.6. In bevel door appliations the backset is measured from the centerline of the bevel (center door thickness).7. When door gasketing or silencers are used, proper allowance must be made for the vertical strike location. 8. The strike opening must be properly aligned with the lock latch and deadbolt (when applicable).
DOOR AND FRAMEPREPARATION FOR
MORTISE LOCKS(1-3/4” THICK WOOD DOORS)
HOLES A
INSIDE
OUTSIDE
OUTSIDEINSIDE
INSIDEOUTSIDE
OUTSIDE
INSIDE
2 3/4”BACKSET
6.50
7.250
8.000
1.250
1.750
3.610
2.440
2.750
4.504.17 REF
6.600
0.219
3.25
3.625
4.000
LOCK BODY CAVITY1.000 WIDE X 6.500 HIGH X 4.500 DEEP SLOT (MAX. 1.125 WIDE FOR SOLID WOOD DOORS)
OUTSIDE OF RH & RHR DOOR
LOCK BODY OUTLINE
0.600
DO
OR E
DG
ESU
RFA
CE
INSIDE OF RH & RHR DOOR
DOOR THICKNESS
+0.031-0.000
0.500” DIA. THROUGH HOLEFOR ESCUTCHEON TRIM(IF APPLICABLE - SEE TABLE)
0.625” DIA HOLE ON INSIDE DOOR SKIN ONLY, FOR THUMBTURN (IF APPLICABLE- REFER TO TABLE)
1.000” DIA. THROUGH HOLE FOR KNOB/LEVER
0.406” DIA.THROUGH HOLES (2X)
0.500” DIA. THROUGH HOLEFOR ESCUTCHEON TRIM ONLY(IF APPLICABLE)
0.600
0.600 0.600
0.600
1.500
1.766
CAVITY DEPTH
+0.031-0.000
MORTISE LOCKHORIZONTAL CENTRELINE
DOOR VERTICALCENTRELINE(HALF OF DOOR THICKNESS)
FACEPLATE CAVITY (IN GREY)
2.440
2.75
4.50
6.600
1.766
0.219
0.600
DO
OR
EDG
ESU
RFA
CE
0.600
0.600
1.500
CAVITY DEPTH
BACKSETVERTICAL LINE
1.750”2.062”
2.438”
4.125”
4.875“
0.875”
1.250
1.062”0.625”
0.375”
3.375”
3.500”
“+0.031” -0.000”
STRIKE CENTRELINELOCK CENTRELINE
+0.031”- 0.000”
0.156” DIA. PILOT HOLE ON WOOD FRAMEOR DRILL & TAP FOR #12-24 NC SCREW ON METAL FRAME2-HOLES
STRIKE & DUSTBOX CAVITY1.06" WIDE X 3.50" HIGH X 1.12" DEEP
0.22”,(+0.02”, -0”)
1.00”
BEVEL CENTRELINE4.50”
HANDING OF DOOR - ORIENTATIONS
ALL DIMENSIONS ARE IN INCHES
IF BEVELED DOOR IS USED
LEFT HAND (LH) RIGHT HAND (RH)
RIGHT HAND REVERSED (RHR)LEFT HAND REVERSED (LHR) ALL DIMENSIONS ARE IN INCHES
• BEFORE DRILLING OR CUTTING CONSULT TRIM STYLE AND TABLE (ON SHEET 1) INDICATING LOCK FUNCTION• LOCK BODY AND FACEPLATE CAVITIES MUST BE CENTERED TO BOTH HORIZONTAL AND VERTICAL CENTERLINES (WITHIN ±1/32”)• FOR 1 3/4” (44.5mm) DOOR THICKNESS
FRAME PREPARATION FOR LOCK STRIKEFOR 1-3/4” THICK DOOR(REFER TO ANSI A156.115W)
0.500" DIA. THROUGH HOLEFOR ESCUTCHEON TRIM(IF APPLICABLE - REFER TO TABLE)
1.312" DIA. HOLE ON OUTSIDE DOOR SKIN FORMORTISE CYLINDER(IF APPLICABLE - REFER TO TABLE)
0.375" DIA. HOLEFOR EMERGENCY KEY(PRIVACY ONLY, OUTSIDE SURFACE ONLY)
1.000" DIA. THROUGH HOLEFOR KNOB/LEVER
0.406" DIA. THROUGH HOLES (2X)
DOOR AND FRAMEPREPARATION FOR
MORTISE LOCKS(1-3/4” THICK WOOD DOORS)
CAN-DM-DPW
TITLE:
www.dorex.comDOREX
DOCUMENT NO:
SHEET 2 OF 2x.xx : 0.03”x.xxx : 0.015”
WOOD DOOR PREPARATION FOR DM SERIES MORTISE LOCK
REVISION: 7
DATE: 15 OCT 2007
REVISION DATE: 06 JAN. 2016
IF ESCUTCHEON TRIM IS USED, DRILL THE ESCUTCHEON MOUNTING HOLES PRIOR TO MAKING THE LOCK BODY CAVITY
DRILL 0.156” DIA. X 1” DEEP PILOT HOLES (2X)
LOCK BODYCAVITY
NOTES:
5.81 REF 3.610
0.562”
DOOR STOPSILENCER
TOLERANCES:
1
Plaster guard by metalframe mfg. Optional for
slip-on drywall frames.
0.093”
1.25” min.
1.00”min. 0.093” 0.16”
For dust box If specified
or
METAL FRAME SECTIONWOOD FRAME SECTION
+-+-
C
CA
CC
A
B
DRAWINGS ARE NOT AT FULL SCALE. DO NOT USE AS TEMPLATE.CAUTION:
1
1
1
DOORFRAME
STRIKE VERTICAL CENTRELINE TO MATCHDOOR EDGE VERTICAL CENTRELINE
+ 0.03, -0”
+ 0.03, -0”
+ 0.015”, -0
BACKSETVERTICAL LINE
DM-DPW-R7-2016-01
4.17 REF
5.81 REF
0.500" DIA. THROUGH HOLEFOR ESCUTCHEON TRIM(IF APPLICABLE - REFER TO TABLE)
1
LOCK BODY OUTLINE
UNLES OTHERWISESPECIFIED
1.12”
REF