in-line pumps lp(-e)/lpe-e - teral.info · suction total head (suction height + suction piping...
TRANSCRIPT
In-line pumps
LP(-e)/LPE-e
50Hz
E-CAT5-P-LPeLP-00-A
LP 32 A 5 .75 - e
①Model②Nominal diameter (32mm)③Type④Frequency (50Hz)⑤Output (0.75kW)⑥Phase (S: Single-phase, None: 3-phase)⑦Motor efficiency None: Standard efficiency (equivalent to IE1) e: Top Runner efficiency (equivalent to IE3)
① ② ③ ④ ⑤ ⑥ ⑦LPE 150 K - 5 15 - e
① ② ③ ⑤ ⑥④
* Please note that some of the devices in the photo may differ from actual devices in coating color, etc.
■Applications
■Features
●Circulation of cold/warm water
●Cooling and air-conditioning systems
●General water supply
●Pressurization of tap water
●Pressurization of industrial water
●Other uses
①Energy-saving pump with a Top Runner efficiency (equivalent to IE3) motor. (Excluding pumps of single-phase and 3-phase 0.15kW or less. Pumps of
3-phase 0.25 to 0.4kW are our high efficiency standard products.)② Installable in the middle of piping, and does not require large installation
space.③ Compact, lightweight, and easy-to-handle because disassembly and
inspection can be performed without removing piping.④ No water leakage through the adoption of a mechanical seal.⑤ Usable for high-temperature and high-pressure water, and suitable as a
circulating pump of cold/warm water.⑥ Easy maintenance (Nominal diameter: 125~200mm) When replacing the mechanical seal, it is unnecessary to disassemble the
pump and remove the motor. In addition, it is possible to replace the LPE model in shorter time than the conventional model.
⑦ Capable of high back pressure spec (Nominal diameter: 125~200mm) Allowable boost pressure up to 1.6MPa supported by simple and
high-rigidity structure based on rational design.⑧ Space-saving (Nominal diameter: 125~200mm) Installable in places where horizontal pumps would be hard to install. The
installation area is approx. 50% compared with our SJ4-e and SKJ-e models of horizontal pumps having comparable output.
⑨ High efficiency of pump (nominal diameter: 125~200mm) Increase in efficiency by 5 to 10% from conventional pumps by optimum
design based on three-dimensional flow analysis and structural analysis.⑩ Compatible mounting dimension with conventional pumps. (Some LPE models require special accessory.)
■Description of types
①Model (LPE, LP *)②Nominal diameter (150mm)③Type * LP is only for 200J.④Frequency (50Hz)⑤Output (15kW)⑥Motor efficiency (Top Runner efficiency :equivalent to IE3)
LP(-e)/LPE-eVolute pumps 2-pole/4-pole, line-shapedCast-iron
2
■Standard specifications●Nominal diameter: 25~100mm
■Special accessories
■Supplementary table
Companion flange……Packings, bolts, and nuts included (Nominal diameter: 32~100mm), sluice valve, check valve, pressure gauge, vacuum gauge, compound gauge, foot valve, welded flange, vibration isolator, spacer (bore diameter 125~200mm: for adjustment of discharge height)
●Nominal diameter: 125~200mm
*1 Contact us for use of brine because it depends on liquid quality.*2 Confirm that the following calculation equation is met. Suction total head (suction height + suction piping loss) ≤ Liquid level atmospheric pressure (10.3m) – NPSHR (Net Positive Suction Head Required) *3 × Margin ratio (1.3)*3 For NPSHR, refer to the graph of Net Positive Suction Head Required.
Fresh water (brine supported as custom-made) *1
0~ 80°CDetermined by liquid temperature, NPSHR and piping
loss on the suction side *2
See the Specification table.Closed
Mechanical seal(SiC vs Carbon)
Sealed ball bearingSCS13
(200J:CAC406)SUS420J2FCD450
Totally enclosed fan-cooled Outdoor type3-phase, 200V (7.5kW or less)
3-phase, 200/400V (11kW or more)1500min-1
JIS 10K standard type
Pumpingliquid
Structure
Material
Motor
Liquid qualityLiquid temperature
Impeller
Shaft seal
Bearing
Impeller
Motor shaftCasingType
Power source
Synchronous rotation speed
Total suction head(In case of 20°C)
Allowable pushing pressure
Flange spec
■Standard accessories
Special companion flange (bolt, nut and packing included) ……………2 sets
●Nominal diameter: 25mm
Packing for flange and coupling cover ……………………………………1 set
●Nominal diameter: 125~200mm
*1 For more than 80°C, contact us separately.*2 Pumps of LP25A, single-phase and 3-phase 0.08kW or less cannot pump up.*3 Refer to the supplemental table shown below for LP25A.*4 The impeller material for LP32A is PPS (polyphenylene sulfide resin).
*1 Not available for LP25A, LP40A and LP50A.
0.04,0.05,0.080.150.250.080.25
PPS resinNORYL resin
SUS304PPS resinSUS304
SUS430SUS303SUS304SUS430SUS304
FC180(EPDM)FC150(NBR)FC200(NBR)
FC180(EPDM)FC200(NBR)
Single-phase,100V
Phase and voltage OutputkW
Shaft materialCasing material(O-ring material)Impeller material
3-phase,200V
Fresh water0~90°C…(0.15kW or less)
0~80°C…(0.25kW or more) *1
−6m *2
For use with the total head 10m or less, take 60% or less of the total head.
See the specification table.Closed
Mechanical sealSealed ball bearing
CAC406 *4
SUS304 (3-phase). See the table below.SUS304 (single-phase, 0.25kW, 0.4kW)
FC200Standard efficiency (equivalent to IE1): Single-phase, 3-phase 0.15kW or less
Top Runner efficiency (equivalent to IE3): 3-phase 0.25kW or moreTotally enclosed self-cooled outdoor type: Single-phase 0.08kW or less,
3-phase 0.08kW, 0.25kWDrip-proof protected type: Single-phase 0.15kW or more, 3-phase 0.15kW
Totally enclosed fan-cooled outdoor type: 0.4kW or moreSingle-phase, 100V (0.05~0.4kW)3-phase, 200V (0.08kW or more)
3000min-1
Special companion flange for nominal diameter 25mmJIS 10K thin type for nominal diameter 32mm or more
Pumpingliquid
Structure
Material *3
Motor
Liquid quality
Liquid temperature
ImpellerShaft sealBearingImpeller
Shaft
Casing
Efficiency
Type
Power source
Synchronous rotation speed
Total suction head(In case of 20°C)
Allowable boost pressure
Flange type
■Special specifications
Structure
MaterialMotor
Paint
Shaft seal
Other
ImpellerPower source
Mechanical seal (SiC vs Carbon) (25~100mm)Mechanical seal (SiC vs SiC) (125~200mm)Drain (below casing) (25~100mm)High back pressure (Allowable boost pressure: 1.6MPa) (125~200mm)SUS304 / SCS13 (25~100mm) *1
3-phase 400V classSpecified color for outer surface, salt-resistant paint, heavy-duty salt-resistant paint, Sewage works agency specification
LP(-e)/LPE-e Volute pumps2-pole/4-pole, line-shapedCast-iron
3
0.020.015 0.03 0.04 0.06 0.08 0.10 0.15 0.30.2 0.4 0.6 0.8 1.0 1.51
2
3
4
6
8
10
15
20
30
40
50〈50Hz〉Synchronous rotation speed 3000min-1
■Selection chart●Nominal diameter: 25~100mm
●Nominal diameter: 125~200mm
〈50Hz〉Synchronous rotation speed 1500min-1
Discharge rate (m3/min)
A5.08A5.08S
LP32
LP25
LP40 LP50 LP65 LP80
65C55.5-e80C57.5-e
100C57.5-e100C55.5-e
80C55.5-e
A5.04S
A5.05S
B51.5-e
B51.5-e
B53.7-e
B52.2-e
B53.7-e
B52.2-e
B51.5-e
B52.2-e
B53.7-e
A5.75-e
A5.75-eA5.25-eA5.25S
A5.25-eA5.25S
A5.75-e
A5.75-e
A5.4-eA5.4S
A5.4-eA5.4S
A5.4-eA5.4S
40B52.2-e
40B51.5-e
A5.15SA5.15
A5.25-eA5.25S
Tota
l hea
d (m
)To
tal h
ead
(m)
Discharge rate (m3/min)
K522-eK511-e
K57.5-e
K511-e
J515-e
J518-e
G522-e
G530-e
F575-e
F555-e
G537-e
FC555-eFC545-eF545-e
GC537-eJ530-eJ522-eJC522-eK518-e
KC518-e
K530-e
J537-e
J518-e
J545-e
J555-e
J575-e
K515-e
5
0.5 1.0 2.0 4.03.0 5.0 10 20
10
20
30
40
50
100 558861
LPE125-e LPE150-e LPE200-eLP200-e
LP(-e)/LPE-eVolute pumps 2-pole/4-pole, line-shapedCast-iron
4
■Net Positive Suction Head Required (NPSHR): Bore diameter 125~200mm●Nominal diameter: 125mm
●Nominal diameter: 150mm
●Nominal diameter: 200mm
* LP200J: NPSHR is 5m. However, if the pump is used with the total head of 10m or less, NPSHR should not exceed 60% of the total head.
0.0
1.0
2.0
3.0
4.0
5.0
6.0
0.0 1.0 2.0 3.0 4.0
NP
SH
R(m
)
Flow rate (m3/min)
Flow rate (m3/min)
0.0
2.0
4.0
6.0
8.0
10.0
12.0
0.0 2.0 4.0 6.0 8.0 10.0 12.0
LPE125J
LPE125G
LPE125K
LPE200K
Flow rate (m3/min)
NP
SH
R(m
)
0.0
2.0
4.0
6.0
8.0
0.0 2.0 4.0 6.0 8.0
LPE150G(C)LPE150J(C)LPE150K[15kW or less]
LPE150K(C)[18.5kW]
LPE150F(C)
NP
SH
R(m
)
LP(-e)/LPE-e Volute pumps2-pole/4-pole, line-shapedCast-iron
5
LP25A5.04SLP25A5.05SLP25A5.08S
0.040.050.080.150.250.250.40.250.40.4
0.0150.020.02
4.35.75.2
0.030.030.035
2.84.74.7
0.040.040.05
1.53.64.3
0.10.10.125
LP25A5.15S 0.025 9.5 0.05 7 0.07 4.5 0.2LP25A5.25S 0.02 13.5 0.04 11.5 0.06 8.5 0.2LP32A5.25S 0.05 9.5 0.09 8 0.125 6 0.39
32LP32A5.4S 0.05 14.2 0.09 12.5 0.125 10.5 0.39LP40A5.25S 0.10 7 0.16 5.5 0.20 4.5 0.39
40LP40A5.4S 0.10 10 0.16 8.5 0.20 7.5 0.39
50 LP50A5.4S 0.16 8 0.25 5.5 0.32 3.5 0.39
25
32
40
50
65
80
100
LP25A5.08LP25A5.15LP25A5.25-eLP32A5.25-eLP32A5.4-eLP32A5.75-eLP40A5.25-eLP40A5.4-eLP40A5.75-eLP40B51.5-eLP40B52.2-eLP50A5.4-eLP50A5.75-eLP50B5.15-eLP50B52.2-eLP50B53.7-eLP65A5.75-eLP65B51.5-eLP65B52.2-eLP65B53.7-eLP65C55.5-eLP80B51.5-eLP80B52.2-eLP80B53.7-eLP80C55.5-eLP80C57.5-eLP100C55.5-eLP100C57.5-e
0.08 0.02 5.2 0.035 4.7 0.05 4.3 0.10.15 0.025 9.5 0.05 7 0.07 4.5 0.20.25 0.02 13.5 0.04 11.5 0.06 8.5 0.20.25 0.05 9.5 0.09 8 0.125 6 0.390.4 0.05 14.2 0.09 12.5 0.125 10.5 0.390.75 0.05 19 0.09 17 0.125 15 0.390.25 0.10 7 0.16 5.5 0.20 4.5 0.390.4 0.10 10 0.16 8.5 0.20 7.5 0.390.75 0.10 16 0.16 14 0.20 13 0.391.5 0.05 28 0.10 27 0.20 23 0.592.2 0.05 37 0.10 36.5 0.20 32.5 0.590.4 0.16 8 0.25 5.5 0.32 3.5 0.390.75 0.16 13 0.25 10.5 0.32 7.5 0.391.5 0.16 21 0.25 19.5 0.32 17 0.592.2 0.16 29.5 0.25 27 0.32 24.5 0.593.7 0.16 41 0.25 39 0.32 36.5 0.540.75 0.25 10 0.40 7.5 0.50 5 0.391.5 0.25 15.5 0.40 13.5 0.60 9.5 0.592.2 0.25 22 0.40 19 0.60 14 0.593.7 0.25 32 0.40 28.5 0.60 21.5 0.595.5 0.25 45 0.40 40 0.50 36 0.391.5 0.40 12.5 0.60 10.5 1.05 4 0.592.2 0.40 15 0.60 13.5 1.20 5.5 0.593.7 0.40 21.5 0.60 19.5 1.20 12.5 0.595.5 0.40 32.5 0.60 29 0.80 24 0.397.5 0.40 42 0.60 37 0.80 30 0.395.5 0.63 23 1.0 20 1.25 17 0.397.5 0.63 33 1.0 27 1.25 21.5 0.39
125
150
200
LPE125K-57.5-eLPE125K-511-eLPE125J-515-eLPE125J-518-eLPE125G-522-eLPE125G-530-eLPE150K-511-eLPE150K-515-eLPE150K-518-eLPE150KC-518-eLPE150J-518-eLPE150J-522-eLPE150JC-522-eLPE150J-530-eLPE150G-537-eLPE150GC-537-eLPE150F-545-eLPE150FC-545-eLPE150F-555-eLPE150FC-555-eLPE150F-575-eLPE200K-522-eLPE200K-530-eLP200J-537-eLP200J-545-eLP200J-555-eLP200J-575-e
7.5 11 15 18.5 22 30 11 15 18.5 18.5 18.5 22 22 30 37 37 45 45 55 55 75 22 30 37 45 55 75
0.80.80.80.80.80.81.61.61.61.61.61.61.61.61.61.61.6 1.6 1.6 1.6 1.6 3.23.23.23.23.23.2
17.823.527.830.836.747.617.322.623.121.426.130.729.333.840.138.245.2 40.9 54.4 49.0 66.7 20.823.628.431.836.543.0
2.02.02.02.02.02.03.23.23.23.23.23.23.23.23.23.23.2 4.0 3.2 4.0 4.0 6.46.46.46.46.46.4
15.721.325.828.835.345.610.219.321.119.522.927.326.030.038.636.844.9 39.4 54.4 47.3 63.8 16.421.323.227.132.440.4
3.03.23.33.53.53.55.05.64.56.05.04.05.56.05.06.04.86.04.86.47.09.0
10.09.0
10.010.010.0
10.114.320.022.830.039.5
8.611.019.613.817.125.518.223.234.629.842.034.951.140.052.010.011.717.719.124.331.8
1.181.131.091.061.000.891.191.141.141.161.111.061.081.020.980.990.940.980.840.890.721.161.131.041.010.960.91
Type
SpecificationsPhase
Allowable boostpressure
MPaTotal head
mDischarge rate
m3/minTotal head
mDischarge rate
m3/minTotal head
mDischarge rate
m3/min
Nominaldiameter
mm
OutputkW
■Specification table
Single-phase
3-Phase
Type
Specifications Allowable boostpressure
MPaTotal head
mDischarge rate
m3/minTotal head
mDischarge rate
m3/minTotal head
mDischarge rate
m3/min
Nominaldiametermm
OutputkW
LP(-e)/LPE-eVolute pumps 2-pole/4-pole, line-shapedCast-iron
6
PhaseVoltage
VCurrent
ARotation speed
min-1TypeOutput
kWThermal
class
Classification Rating
Torque%
CurrentA
Method
Starting
Load side(D.S)
Anti-load side(O.S)
Bearing
Singlephase
Drip-proofprotected type
Totally enclosedself-cooling
outdoor type
Totally enclosed self-cooling outdoor type
Drip-proof protected type
Totally enclosedfan-cooled outdoor
type
3-phase
0.040.050.080.150.250.40.080.150.250.40.751.52.23.75.57.5
1.0 1.3 1.9 2.9 4.5 6.1 0.6 1 1.2 1.7 3.2 5.9 8.414.9 22 28.4
2870279028652750294028502885278029102870288028952880293029302920
98.1 77.2 81.9 53.2 85 51 486.5 370.5 460 379 311 312 400 319 235 242
3.6 3.6 6.6 8.3 33.4 33.4 3.4 4.8 10.5 14.2 26.8 49.3 81.4 143 182 234
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Direct-on-Line start
Direct-on-Line start
Direct-on-Line start
Direct-on-Line start
Direct-on-Line start
Direct-on-Line start
Direct-on-Line start
Direct-on-Line start
Direct-on-Line start
Direct-on-Line start
FFFEEEFEFFFBBBBB
6201UUC36201UUC36201UUC36200DDU6204ZZC36204ZZC36201UUC36200DDU6204ZZC3E6204ZZC3E6205ZZC3E6306ZZC3E6306ZZC3E6307ZZC3E6308ZZC3E6308ZZC3E
6201UUC36201UUC36201UUC36200DDU6203ZZC36203ZZC36201UUC36200DDU6203ZZC3E6203ZZC3E6204ZZC3E6205ZZC3E6205ZZC3E6306ZZC3E6306ZZC3E6306ZZC3E
100100100100100100200200200200200200200200200200
■Motor specification table●Nominal diameter: 25~100mm
3-phaseTotally enclosed
fan-cooled outdoortype
7.5111518.522303745557590
29.043.558.069.083.0
109140168202276330
14651470147014701470147014701470147514751475
315370364294325295343324317263255
260366480576673919
12111435180024012720
Direct-on-Line start
Direct-on-Line start
Direct-on-Line start
Direct-on-Line start
Direct-on-Line start
Direct-on-Line start
Direct-on-Line start
Direct-on-Line start
Direct-on-Line start
Direct-on-Line start
Direct-on-Line start
FFFFFFFFFFF
6308ZZC36309ZZC36309ZZC36311ZZC36311ZZC36312ZZC36313ZZC36313ZZC36314ZZC36317ZZC36317ZZC3
6306ZZC36309ZZC36309ZZC36311ZZC36311ZZC36311ZZC36312ZZC36312ZZC36313ZZC36314ZZC36314ZZC3
200V200V200V200V200V200V200V200V200V200V200V
* Urea grease is used for bearings.* Piping connection dimensions are the same as those of a conventional pump (product equipped with IE1 motor). The motor is also compatible, therefore, it is possible to replace with the Top Runner (equivalent to IE3) motor. However, pay attention to the following.①The rotation speed of the motor tends to increase because of its characteristics. The current may exceed the rated current value. Adjust the flow rate to use the motor in a range which does not exceed the rated current value.②Some motor dimensions have been changed from conventional ones. Confirm with the dimension table for details.
* Urea grease is used for the bearing. However, lithium grease is used for 0.15kW.
●Nominal diameter: 125~200mm
PhaseVoltage
VCurrent
ARotation speed
min-1TypeOutput
kWThermal
class
Classification Rating
Torque%
CurrentA
Method
Starting
Load side(D.S)
Anti-load side(O.S)
Bearing
LP(-e)/LPE-e Volute pumps2-pole/4-pole, line-shapedCast-iron
7
LPE125K-57.5-eLPE125K-511-eLPE125J-515-eLPE125J-518-eLPE125G-522-eLPE125G-530-eLPE150K-511-eLPE150K-515-eLPE150K-518-eLPE150KC-518-eLPE150J-518-eLPE150J-522-eLPE150JC-522-eLPE150J-530-eLPE150G-537-eLPE150GC-537-eLPE150F-545-eLPE150FC-545-eLPE150F-555-eLPE150FC-555-eLPE150F-575-eLPE200K-522-eLPE200K-530-eLP200J-537-eLP200J-545-eLP200J-555-eLP200J-575-e
0350/2100/S/AR1S1/BS0350/2100/S/AR1S1/BS0350/2100/S/AR1S1/BS0350/2100/S/AR1S1/BS0450/2100/S/AR1S1/BS0450/2100/S/AR1S1/BS0350/2100/S/AR1S1/BS0350/2100/S/AR1S1/BS0350/2100/S/AR1S1/BS0350/2100/S/AR1S1/BS0450/2100/S/AR1S1/BS0450/2100/S/AR1S1/BS0450/2100/S/AR1S1/BS0450/2100/S/AR1S1/BS0450/2100/S/AR1S1/BS0450/2100/S/AR1S1/BS0550/2100/S/AR1S1/BS0550/2100/S/AR1S1/BS0550/2100/S/AR1S1/BS0550/2100/S/AR1S1/BS0550/2100/S/AR1S1/BS0450/2100/S/AR1S1/BS0450/2100/S/AR1S1/BS0650/2100/S/AR1S1/BS0650/2100/S/AR1S1/BS0650/2100/S/AR1S1/BS0650/2100/S/AR1S1/BS
G130G130G130G130K150K150G130G130G130G130K150K150K150K150K150K150K160K160K160K160K160K150K150G105G105G105G105
■Component parts list
LP25A5.04SLP25A5.05SLP25A5.08SLP25A5.15SLP25A5.25SLP32A5.25SLP32A5.4SLP40A5.25SLP40A5.4SLP50A5.4SLP25A5.08LP25A5.15LP25A5.25-eLP32A5.25-eLP32A5.4-eLP32A5.75-eLP40A5.25-eLP40A5.4-eLP40A5.75-eLP40B51.5-eLP40B52.2-eLP50A5.4-eLP50A5.75-eLP50B51.5-eLP50B52.2-eLP50B53.7-eLP65A5.75-eLP65B51.5-eLP65B52.2-eLP65B53.7-eLP65C55.5-eLP80B51.5-eLP80B52.2-eLP80B53.7-eLP80C55.5-eLP80C57.5-eLP100C55.5-eLP100C57.5-e
EA-104-9EA-104-9EH-791-PB-8EA560-008H-16H-16H-16H-16H-16H-16
EH-791-PB-8EA560-008H-16H-16H-16H-16H-16H-16H-16H-20HH-20HH-16H-16H-20HH-20HH-20HH-16H-20HH-20HH-20HEA560-25H-20HH-20HH-20HEA560-25EA560-25EA560-25EA560-25
G80G80G95G95G120G120G120G120G120G120G95G95G120G120G120G140G120G120G120K184K184G120G120G140K184K184G120G140G140K184K198G140G140G140K198K198K198K198
TypeO-ring
(for casing)Mechanical seal
●Nominal diameter: 25~100mm
TypeO-ring
(for Seal cover)Mechanical seal
●Nominal diameter: 125~200mm
LP(-e)/LPE-eVolute pumps 2-pole/4-pole, line-shapedCast-iron
8
LP25A5.04SLP25A5.05SLP25A5.08S
0.040.050.08
303042
696995
696985
182182224
102102 99.5
220.5220.5230
134.5134.5139.5
6.06.08.0
TypeOutputkW A D E H
Pump and motor
KA L W
Approx.masskg
Nominaldiameter
d
25
(Unit: mm)■DimensionsNominal diameter: 25mmPhase/voltage: single-phase/100VOutput: 0.15kWApprox. mass: 7.5kg
Nominal diameter: 25mmPhase/voltage: 3-phase/200VOutput: 0.15kWApprox. mass: 6.4kg
Nominal diameter: 25mmPhase/voltage: 3-phase/200VOutput: 0.08kWApprox. mass: 7.0kg
●LP25A5.08 ●LP25A5.15■Assembly drawing ■Assembly drawing
φ102
Rp1
KA
66.5
W
L
A
Rp1
105
105
Earth terminal M4
External length 1900
Earth terminal M4
Drain plugG⅛×3 locations
20 20
Rotation direction
Suction Discharge
2×M10
E
H
70
φ102
70
D
2 2
Rp1
99.5
230
42
Rp1
Drain plugG⅛×3 locations
Cable glandApplicable cable diameter φ9~14
20 2085
224
95
2 2
●LP25A5.04S~5.08S ●LP25A5.15S■Assembly drawing ■Assembly drawing
66.5
139.
5
2×M10
6257
.5
18423 23
21 PT1 ScrewPS⅛ DrainPT1 Screw 21
230
φ9290
Power cable 2m
Air vent
211.
541
.5
253
Rotation direction
Suction Discharge
6257
.5
18423 23
PT1 Screw
PS⅛ Drain
PT1 Screw
2121
230
90Cable 0.5m
Air vent
195.
541
.5
237
φ92
LP(-e)/LPE-e Volute pumps2-pole/4-pole, line-shapedCast-iron
9
●LP25A5.25S
●LP32~50A Single phase
■Assembly drawing
■Assembly drawing
Type Output A B D E HNominaldiameter
d
(Unit: mm)■Dimensions
Flange dimensions
Plug ⅜B
Drain plug ⅛B
LP32A5.25S 0.250.40.250.40.4
7070808085
276276278278283
140140150150160
140140150150150
280280300300310
LP32A5.4SLP40A5.25SLP40A5.4SLP50A5.4S
32
40
50
LP32A5.25S 346346358358368
173173171171178
9292919195
8181808083
2827302931
LP32A5.4SLP40A5.25SLP40A5.4SLP50A5.4S
Air vent
Drain plug ⅛BNominal diameter: 25mmPhase/voltage: single-phase/100VOutput: 0.25kWApprox. mass: 19.0kg240
60φ
25
φ25
(89
)
75
φ25
95
2×φ12Rotation direction
81.5
272
332
76.5
158
φ129
120120
φd
φd
A
H
W
W2
W1
B
L
φ129
Air vent
Rotation direction
DE
(89
)
kW
Approx.masskg
Type L W W1 W2
☆Flange dimensions: JIS 10K thin type or equivalent
LP(-e)/LPE-eVolute pumps 2-pole/4-pole, line-shapedCast-iron
10
●LP25A5.25-e
■Assembly drawing
Flange dimensions
●LP32~65A-e 0.25~0.75kWLP32A5.25-eLP32A5.4-eLP32A5.75-eLP40A5.25-eLP40A5.4-eLP40A5.75-eLP50A5.4-eLP50A5.75-eLP65A5.75-e
0.250.4
0.750.250.4
0.750.4
0.750.75
707070808080858595
295295304297297306302311318
140140140150150150160160175
140140140150150150150150165
280280280300300300310310340
Type OutputkW A B D E H
Approx.mass
kg
Nominaldiameter
d
32
40
50
65
LP32A5.25-eLP32A5.4-eLP32A5.75-eLP40A5.25-eLP40A5.4-eLP40A5.75-eLP50A5.4-eLP50A5.75-eLP65A5.75-e
217217211219219213224218225
103103111103103111103111111
133133141133133141133141141
365365374377377386387396413
145145163145145163145163163
214214226213213221216224228
252935263035333742
Type LKLKGKA WMD
(Unit: mm)
☆Flange dimensions: JIS 10K thin type or equivalent
■Dimensions
■Assembly drawing
Nominal diameter: 25mmPhase/voltage: 3-phase/200VOutput: 0.25kWApprox. mass: 18.0kg
240120120Drain plug ⅛B
(62)
(1
03
)
G½
60
29
1
35
1
(2
13
)
φ145
(2
10
)
φ25
φ25
φ25
75
2×φ12
95
Rotation direction
Air vent
(62)G½
(K
G)
(K
L)(
W)
φMD
Plug ⅜B
Drain plug ⅛B
H
DE
Air vent
Rotation direction
L
B
(K
A)
A
φd
φd
(1
33)
LP(-e)/LPE-e Volute pumps2-pole/4-pole, line-shapedCast-iron
11
●LP-B-e
■Assembly drawing
■Assembly drawing
LP40B51.5-eLP40B52.2-eLP50B51.5-eLP50B52.2-eLP50B53.7-eLP65B51.5-eLP65B52.2-eLP65B53.7-eLP80B51.5-eLP80B52.2-eLP80B53.7-e
1.52.21.52.23.71.52.23.71.52.23.7
8080808080959595
100100100
345345350350393358358398360360403
170170155175175175175175200200200
170170155165165165165165190190190
340340310340340340340340390390390
40
50
65
80
LP40B51.5-eLP40B52.2-eLP50B51.5-eLP50B52.2-eLP50B53.7-eLP65B51.5-eLP65B52.2-eLP65B53.7-eLP80B51.5-eLP80B52.2-eLP80B53.7-e
214214219219255227227260229229265
123123123123147123123147123123147
155155155155177155155177155155177
425425430430473453453493460460503
266266243266289251251289254254278
2934313557353961474667
(Unit: mm)■Dimensions
●LP-C-eLP65C55.5-eLP80C55.5-eLP80C57.5-eLP100C55.5-eLP100C57.5-e
5.55.57.55.57.5
95100100115115
458461461460460
185200200225225
185190190205205
370390390430430
65
80
100
LP65C55.5-eLP80C55.5-eLP80C57.5-eLP100C55.5-eLP100C57.5-e
235238238237237
194194194194194
260260260260260
553561561575575
402402402402402
81879894
105
(Unit: mm)■Dimensions
Air vent
DE
H
Drain plug ⅛B
AB
L
(K
A)
Plug ⅜B
Rotation direction
G¾ (62)
φd
(W
)
(K
L)
(K
G)
B
L
D
G1¼
KA
E
H
A
Plug ⅜B
Rotation direction
Drain plug ⅛B
Air vent
☆Flange dimensions: JIS 10K thin type or equivalent
☆Flange dimensions: JIS 10K thin type or equivalent
φd
KG
KL
W
φdφd
Type OutputkW
A B D E H
Approx.mass
kg
Nominaldiameter
d
Type KLKGKA WL
Type OutputkW
A B D E HNominaldiameter
d
Type KLKGKA WLApprox.mass
kg
LP(-e)/LPE-eVolute pumps 2-pole/4-pole, line-shapedCast-iron
12
MS(Disassembly dimensions)
■Assembly drawing●LPE125~200-e/LP200-e
4×φ FA foundation bolt hole(Recommended foundation bolt FD)
with drain only in case of LPE125G-e, LPE150G-e, LPE150F-e
LPE125K-57.5-eLPE125K-511-eLPE125J-515-eLPE125J-518-eLPE125G-522-eLPE125G-530-eLPE150K-511-eLPE150K-515-eLPE150K(C)-518-eLPE150J-518-eLPE150J(C)-522-eLPE150J-530-eLPE150G(C)-537-eLPE150F(C)-545-eLPE150F(C)-555-eLPE150F-575-eLPE200K-522-eLPE200K-530-eLP200J-537-eLP200J-545-eLP200J-555-eLP200J-575-e
7.51115
18.522301115
18.518.5223037455575223037455575
250250250250250250250250250250250250250250250250295295330330330330
608608608608608608620620620620620620650660690690690690763763763763
215226234251254254231231251260260260258311311311267267277277277277
700700800800800800800800800800800800800
100010001000
900900
1000100010001000
256256276277298306286286286314314314320361361426332332392392452513
1067114211721170117012101154118411831183118312221388139814321568125312921523152315711577
TypeOutput
kW
270323358406453487358377426477486520615702815982467501798794924
1050
A B H KG KL L
G1G1 ½G1 ½G2G2G2
G1 ½G1 ½G2G2G2G2
G2 ½G2 ½G2 ½G3G2G2G2G2G2G3
MB
90120120120120120120120120120120120150150150150120120150150150150
MS
471482510528552560517517537574574574578672672737599599669669729790
W
360360360360360360430430430430430430430500500500500500500500500500
BL
300300300300300300350350350350350350350410410410410410410410410410
BP
32323232323232323232323232505050323235353535
BH
23232323232323232323232323252525252525252525
FA
M20M20M20M20M20M20M20M20M20M20M20M20M20M22M22M22M22M22M22M22M22M22
FDNominaldiameter
d
125
150
200
(Unit: mm)■DimensionsApprox.mass
kg
Air vent
Rotation direction
BL Plug ⅜B
Plug ⅜B
Drain plug ⅜B
Drain plug ⅜B
BLH
BP BP
Air vent plug
MB
Air vent
(K
L)
(W
)
KG
LB
BH
Aφ
d
φd
LP(-e)/LPE-e Volute pumps2-pole/4-pole, line-shapedCast-iron
13
7
9
10
11
58 6 4 3 1
2
No. Part name Qty Material
1 Casing
Frame
Impeller
Impeller nut
Liner ring
Key
O-ring
Mechanical seal
Air vent valve
Deflector
Motor
1 FC200
2 1 FC200
3 1 CAC406
4 1 SUS304
5 1 CAC406
6 1 SUS420J2
7 1 NBR
8 1 Ceramic vs Carbon
9 2 C3604BD
10 1 CR
11 1
●LP40~50A Single phase
■Example of sectional drawing ■Parts list
Applicable models: LP40A5.25S / LP40A5.4S / LP50A5.4S
No. Part name Qty Material
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Casing
Frame
Impeller
Impeller nut
Liner ring
Key
Deflector
Mechanical seal
O-ring
Plug
Air vent valve
Drain plug
Motor shaft *1
Motor
1
1
1
1
1
1
1
1
1
2
2
1
1
1
FC200
FC200
CAC406
SUS304
CAC406
SUS304
CR
Ceramic vs Carbon
NBR
SWCH
C3604BD
SWCH
SUS304+S35C
–
●LP40~80B-e 1.5kW
■Example of sectional drawing ■Parts list
Applicable models: LP40B-51.5-e / LP50B-51.5-e LP65B-51.5-e / LP80B-51.5-e1* The indicated materials are equivalent products.
5 4
8 11
7
1
2
3 6
9
13
14
12
10
LP(-e)/LPE-eVolute pumps 2-pole/4-pole, line-shapedCast-iron
14
●Pressure gauge / compound gaugePlan to attach a pressure gauge/compound gauge to the piping side.
○
●LPE-e (Excluding 200J)
●Nominal diameter: 25~100mm
■Example of sectional drawing
No. Part name Qty Material
1
2
3
4
5
6
7
8
9
Casing
Frame
Seal cover
Impeller
Main shaft
Liner ring
Mechanical seal
O-ring
O-ring
1
1
1
1
1
2
1
1
1
FCD450
FCD450
FCD450
SCS13
SUS420J2
CAC406
SiC vs Carbon
NBR
NBR
■Parts list
●Nominal diameter: 125~200mm■Installation method
No. Part name Qty Material
10
11
12
13
14
15
16
17
Coupling
Coupling cover
Parallel pin
Air vent valve
Air vent plug
Plug
Drain plug
Motor
1
2
1
1
2
2
2*
1
FCD450
SUS304
S45C
C3771B
C3604BD
SWCH
SWCH
─
Applicable models: LPE125-e / LPE150-e / LPE200-e* 3 drain plugs for LPE125G-e,LPE150G-e and LPE150F-e.
○ ×
× ○Other installation methods are unsupported.
172
11
13
3
14
7
4
15
1
16
10
12
5
8
9
6
LP(-e)/LPE-e Volute pumps2-pole/4-pole, line-shapedCast-iron
15
,
TERAL INC.Head Office 230, Moriwake, Miyuki-cyo, Fukuyama-city, Hiroshima, 720-0003, Japan
Tel.+81-84-955-1111 Fax.+81-84-955-5777www.teral.net
Teral Asia LimitedRoom 1001,10/F, Olympia Plaza, 255 King's Road, North Point, Hong Kong
Tel.+852-2571-0935 Fax.+852-2571-0619
TERAL THAI CO.,LTD.150 Moo 16 Udomsorayuth Rd., T.Bangkrasan, A.Bangpa-In, Ayutthaya 13160 Thailand
Tel.+66-3535-2148-9 Fax.+66-3535-2150
TERAL TRADING & SERVICE CO.,LTD. 150 Moo 16 Udomsorayuth Rd., T.Bangkrasan, A.Bangpa-In, Ayutthaya 13160 Thailand
Tel.+66-3535-2145-7 Fax.+66-3535-8549
Teral Malaysia Sdn.Bhd. 10, Jalan SS13/6A, Subang Jaya Industrial Estate, 47500, Subang Jaya, Selangor D.E, Malaysia
Tel.+60-3-5611 5775 Fax.+60-3-5612 5775
PT.Teral Indonesia Pumps and Fans Jalan BSD Sektor XI Taman Tekno, Block G3 No.8, Setu Tangerang Selatan, Banten, Indonesia 15314
Tel.+62-21-29665778 Fax.+62-21-75673913
Teral Vietnam Limited Liability Company Room 1306, 13th Floor, BIDV Tower, 194 Tran Quang Khai Street, Ly Thai To Ward, Hoan Kiem District, Hanoi, Vietnam
Tel.+84-24-3935-2790 Fax.+84-24-3935-2800
Teral General Machine (Shanghai) Co.,Ltd. No.285, Yuan Qu Road(N), Bei Qiao, Min Hang District, Shanghai 201109, China
Tel.+86-21-6490-9128 Fax.+86-21-6490-9126
Teral-Aerotech Fans Private Ltd. Plot No.188-189, Ecotech Extension-1, Surajpur Kasna Road, Greater Noida-201306, Uttar Pradesh, India
Tel.+91-9810162210, +91-9310162210
Teral Middle East F.Z.C. 1806-002, 18th floor, BB1, Mazaya Business Avenue, JLT, Dubai, UAE. PO Box 414781
Tel.+971-4369 9039
Teral Pumps & Fans North America Ltd. Suite # 197, 800-15355 24 Ave Surrey, B.C., CANADA V4A 2H9
Tel.+1-604-839-1008
2017 01
E-CAT5-P-LPeLP-00-A