improved direct torque control of induction motors using
TRANSCRIPT
Archives of Control SciencesVolume 23(LIX), 2013No. 3, pages 361–376
Improved direct torque control of induction motorsusing adaptive observer and sliding mode control
DJILALI KOUCHIH, MOHAMED TADJINE and MOHAMED SEGHIR BOUCHERIT
This paper presents the synthesis of an adaptive observer which is used for the improvementof the direct torque control of induction motor drives. The observer detects stator flux compo-nents in two-phase stationary reference frame, rotor speed and stator resistance by measureof the stator terminal voltages and currents. The observer is adapted using a simple algorithmwhich does not imply a high computational load. Stability analysis based on Lyapunov theoryis performed in order to guarantee the closed loop stability. Simulation tests under load distur-bance and stator resistance variation are provided to evaluate the consistency and performanceof the proposed control technique in the low and high speeds.
Key words: adaptive observer, direct torque control, induction motor, sensorless, slidingmode control
1. Introduction
Direct Torque Control (DTC) is currently known as the technique being mostly em-ployed to control induction motors (IM). It requires accurate knowledge of the magni-tude and the angular position of the controlled flux. The flux is conventionally obtainedfrom the stator voltage model, using the measured stator voltages and currents [1-2].This method uses open loop pure integration and suffers from the well known problems,especially at low speed operation mode [3].
Many researchers have been involved in designing of sensorless control of the IM.Most methods are essentially based on the Model Reference Adaptive System (MRAS)or on the reactive power based reference model [4-5]. The MRAS algorithm is very sim-ple but its greatest drawback is the sensitivity to uncertainties in the motor parameters.Others methods, based on Extended Kalman Filter (EKF) or on the intelligent techniques(fuzzy logic and neural networks), have been used by many authors [6-11]. These meth-ods imply a high computational load. In addition, the variable structure techniques arealso used by many researchers [12-16].
D. Kouchih is with Electronic Department, University Saad Dahlab, B.P. 270, Blida, Algeria. E-mail: [email protected]. M. Tadjine and M.S. Boucherit are with Process Control Laboratory, Auto-matic Control Department, ENP, 10, Avenue Badi H., B.P. 182, Alger, Algeria. E-mails: [email protected],ms [email protected].
Received 14.03.2013.
10.2478/acsc-2013-0022
UnauthenticatedDownload Date | 1/19/18 1:34 AM
362 D. KOUCHIH, M. TADJINE, M.S. BOUCHERIT
Generally, the rotor speed estimation is affected by parameter variations, especiallythe stator resistance due to temperature, particularly at low speeds [17-18]. Therefore, toimprove the estimation of the components of the stator flux, it’s necessary to compensatethis parameter variation in sensorless control by using an online adaptation of the statorresistance.
On the other hand and for the speed control, the parametric variation modifies theperformances of the control system when we use regulator with fixed parameters. How-ever, the performances will be degraded face to internal and external disturbances [19].To offer control robustness, many strategies have been proposed in literature [20-24]. Inthis work, we are interested to the Sliding Mode Control (SMC). The SMC can offermany good properties [25]. The problem of undesirable chattering can be remedied byreplacing the switching function by a smooth continuous function [26].
2. DTC strategy
2.1. Principles
The basic idea of the DTC is to choose the optimal vector voltage which producesthe desired flux and torque. The stator flux is given by:
Φs = Φs0 +
t∫0
(V s −RsIs)dt. (1)
If the stator resistance is ignored, the stator flux can be approximated:
Φs ≈ Φs0 +
t∫0
V sdt. (2)
During one period of sampling Te, the vector voltage applied to the machine remainsconstant, we can write:
Φs(k+1)≈ Φs(k)+V sTe, (3)
so the increment is∆Φs ≈V sTe. (4)
Therefore, to increase the stator flux, we can apply a vector of voltage that is co-linearin its direction and vice-versa.
The electromagnetic torque produced by the IM can be expressed:
Ce = kT ΦsΦr sinγ (5)
where kT is a constant [18]. The electromagnetic torque depends upon the effective valueof the stator flux and rotor flux and their relative position γ. Actual torque and flux arecompared with the reference values and control signals are produced.
10.2478/acsc-2013-0022
UnauthenticatedDownload Date | 1/19/18 1:34 AM
IMPROVED DIRECT TORQUE CONTROL OF INDUCTION MOTORSUSING ADAPTIVE OBSERVER AND SLIDING MODE CONTROL 363
The stator voltage is being obtained using the following equation:
V s =2Udc
3
[Sa +Sbe j 2π
3 +Sce j 4π3
](6)
where Udc, Si (i = a,b,c) are DC voltage and the signals of the gats of the inverter,respectively. The choice of the stator vector voltage depends on the desired variation forthe module of stator flux, upon its rotation sense and the desired evolution for the torque.Through the components of stator flux indicated by the reference point (α,β) bound tothe stator, we can decompose the space of stator flux into six sectors [12]. The blockdiagram of an induction motor based DTC strategy is drawn in figure 1. The structure ofadaptive observer is presented in figure 2.
Figure 1. DTC bloc diagram.
Figure 2. Global adaptive observer.
10.2478/acsc-2013-0022
UnauthenticatedDownload Date | 1/19/18 1:34 AM
364 D. KOUCHIH, M. TADJINE, M.S. BOUCHERIT
2.2. Correction of the stator flux
We use a two-level comparison of hysteresis in order to maintain the extremity of thevector of stator flux in one circular crown. A Boolean variable indicates if the amplitudeof the flux must be increased (δ = 1) or (δ = 0) decreased in order to maintain:
|Φ∗s −Φs|¬ ∆Φs (7)
where Φ∗s is the reference stator flux and ∆Φs the stator flux hysteresis band.
2.3. Correction of the torque
We use a three-level comparison of hysteresis in order to control the motor in bothsenses of rotation. Variable µ indicates if the torque must be increased (µ = 1), to main-tain its constant (µ = 0) and (µ = −1) to reduce the torque. This correction assures tooperate in all four quadrants.
The stator voltage applied to the motor depends upon the position of the stator fluxin the sectors. The optimal switching logic defines the best vector and flux references.Table 1 shows the switching order.
Table 5. Switching table of the IM based DTC
Sectors 1 2 3 4 5 6
δ = 1µ =+1 110 010 011 001 101 100µ = 0 111 000 111 000 111 000
µ =−1 101 100 110 010 011 001
δ = 0µ =+1 010 011 001 101 100 110µ = 0 000 111 000 111 000 111
µ =−1 001 101 100 110 010 011
2.4. Correction of mechanical speed
To correct the mechanical speed, we use a sliding mode controller. The sliding modetechnique is developed from variable structure control to reject the disturbances, model-ing uncertainties or parameter variation. It is a technique to adjust feedback by previouslydefining surface [25]. The system which is controlled will be forced to that surface, thenthe behavior of the system slides to the desired equilibrium point.
Design of the control system will be demonstrated for a nonlinear multi-input systemof the form [25]:
X (ni)i (t) = fi(X)+
m
∑j=1
bi j(X)U j, i = 1, ...,m, j = 1, ...,m (8)
10.2478/acsc-2013-0022
UnauthenticatedDownload Date | 1/19/18 1:34 AM
IMPROVED DIRECT TORQUE CONTROL OF INDUCTION MOTORSUSING ADAPTIVE OBSERVER AND SLIDING MODE CONTROL 365
where the vector U of components U j is the control input vector, and the state X iscomposed with Xi and their first (ni − 1) derivatives. Such systems are called squaresystems, since they have as many control inputs U j as states to be controlled Xi. We areinterested in the problem of having the state X track a desired time-varying state Xd .
Let us define a vector s of components si by:
si =
(ddt
+λi
)ni−1
ei, (9)
ei = Xdi −Xi. (10)
The purpose of the sliding mode control is to keep the system motion on the manifoldS, which is defined as:
S = X : e = 0 (11)
where e is the tracking error vector
e = Xd −X . (12)
The sliding mode control should be chosen such that the candidate Lyapunov func-tion Vi satisfies the Lyapunov stability criteria. If we let:
Vi =12
s2i (13)
thenVi = sisi. (14)
The candidate Lyapunov function should satisfy the Lyapunov stability criteria. This canbe assured for:
12
ddt
s2i =−ηi |si| ηi > 0. (15)
Equation (13) states that the squared distance to the surface, measured by s2i decreases
along all system trajectories. The control function can be expressed as follows [26]:
Ucomi =Ueq
i +Uni (16)
Where Ueqi is the equivalent control function and Un
i is the correction factor which mustbe calculated so that the Lyapunov stability condition is satisfied. The correction factorcan be expressed as [19]:
Uni = Kisgn(si). (17)
Here sgn is the sign function and Ki is the controller gain designed from the Lyapunovstability. It was well known that sliding mode technique generates undesirable chatter-ing. This problem can be remedied by replacing the switching function by a smoothcontinuous function. One possible approximation is the sigmoid-like function [26]
sat (si) =si
|si|+ψi(18)
10.2478/acsc-2013-0022
UnauthenticatedDownload Date | 1/19/18 1:34 AM
366 D. KOUCHIH, M. TADJINE, M.S. BOUCHERIT
where ψi is a small positive scalar.For the correction of the mechanical speed, the control function will satisfy reaching
conditions in the following form
T ∗e = T eq
e +T ne (19)
where T ∗e is the reference torque, T eq
e is the equivalent control torque, T ne is the correction
factor and must be calculated so that the stability condition for the selected control issatisfied.
For n = 1, the sliding surface can be expressed by:
s(Ω) = Ω∗−Ω. (20)
During the sliding mode and in permanent regime, we have:
s(Ω) = 0, s(Ω) = 0. (21)
We haveΩ =
1J(Te−Tl − f vΩ) (22)
where J is the inertia of the rotor and the connected load, Te the electromagnetic torque,Tl the load torque, Ω is the mechanical angular speed and fv is the viscose friction coef-ficient. The equivalent control can be expressed as follows
T eqe = J
(Ω∗+Tl + fvΩ
). (23)
During the convergence mode, the condition s(Ω)s(Ω)¬ 0 must be verified. We obtain:
s(Ω) =−1J
T ne . (24)
Therefore the correction factor is given by:
T ne = K · sat (s) . (25)
To verify the system stability condition, parameter K must be positive.
3. Adaptive observer
The objective is to determine the adaptation mechanism of the speed and the statorresistance. The structure of the observer is based on the induction motor model in stator
10.2478/acsc-2013-0022
UnauthenticatedDownload Date | 1/19/18 1:34 AM
IMPROVED DIRECT TORQUE CONTROL OF INDUCTION MOTORSUSING ADAPTIVE OBSERVER AND SLIDING MODE CONTROL 367
reference frame. The state equations of the induction motor can be expressed as follows[27]:
diαs
dt=− 1
σLs
(Rs +Rr
L2m
L2r
)iαs +
1σLs
RrLm
L2r
Φαr +1
σLsω
Lm
LrΦβr +
1σLs
vαs
diβs
dt=− 1
σLs
(Rs +Rr
L2m
L2r
)iβs −
1σLs
ωLm
LrΦαr +
1σLs
RrLm
L2r
Φβr +1
σLsvβs
dΦαr
dt=
RrLm
Lriαs −
Rr
LrΦαr −ωΦβr
dΦβr
dt=
RrLm
Lriβs −
Rr
LrΦβr +ωΦαr
(26)
where vαs, vβs are the components of stator voltage vector, ids, iqs are the componentsof stator current vector, Φαr, Φβr are the components of rotor flux vector, σ is the leak-age factor, Rs and Rr are stator and rotor resistance, Ls and Lr represent the stator androtor cyclic inductances and Lm is the stator-rotor cyclic mutual inductance. ω is themechanical pulsation.
The previous state system can be expressed in the form:dXdt
= AX +BU
Y =CX(27)
where
XT =(iαs iβs Φαr Φβr
), Y =
(iαs
iβs
), U =
(vαs
vβs
).
The matrices are defined by:
A =
−a 0RrLm
Lrbω
Lm
b
0 −a −ωLm
bRrLm
LrbRrLm
Lr0 −Rr
Lr−ω
0RrLm
Lr+ω −Rr
Lr
B =
1σLs
0
01
σLs0 00 0
, C =
(1 0 0 00 1 0 0
),
10.2478/acsc-2013-0022
UnauthenticatedDownload Date | 1/19/18 1:34 AM
368 D. KOUCHIH, M. TADJINE, M.S. BOUCHERIT
a =1
σLs
(Rs +Rr
L2m
L2r
), b = σLsLr, σ = 1− L2
m
LsLr
A linear state observer can be then derived by considering the mechanical speedas a constant parameter since its variation is very slow in comparison to the electricalvariables. The model of the observer is defined as follows [28]:
dXdt
= AX +BU +G(Y −Y
)Y =CX .
(28)
The machine parameters are assumed to be perfectly known, the mechanical pulsationand the stator resistance are unknown. Let define:
δω = ω−ωδRs = Rs −Rs.
(29)
The symbol „^” denotes estimated values and G is the observer gain matrix.We will determine the differential system describing the evolution of the error:
e = X − X . (30)
The state matrix of the observer can be written as:
A = A+δA (31)
where
δA =
− 1σLs
δRs 0 0Lm
bδω
0 − 1σLs
δRs −Lm
bδω 0
0 0 0 −δω0 0 +δω 0
. (32)
Then, we can write:dXdt
= AX +BU +G(Y −Y
)(33)
ordXdt
= AX +BU +GCe. (34)
From (27), (28) and (30), we get:
dedt
= AX − AX +GCe, (35)
10.2478/acsc-2013-0022
UnauthenticatedDownload Date | 1/19/18 1:34 AM
IMPROVED DIRECT TORQUE CONTROL OF INDUCTION MOTORSUSING ADAPTIVE OBSERVER AND SLIDING MODE CONTROL 369
thusdedt
= (A+GC)e−δAX . (36)
Let define the Lyapunov function as:
V = eT e+(δω)2
λ1+
(δRs)2
λ2(37)
where λ1 and λ2 are positive scalars. This function should contain terms of the differ-ences δω and δRs to obtain mechanism adaptation.
The stability of the observer is guaranteed for the condition [25]:
dVdt
< 0. (38)
The derivative of the Lyapunov function is as follows
dVdt
= 2eT dedt
+2δωλ1
dδωdt
+2δRs
λ2
dδRs
dt. (39)
First element of (39) can easily calculated
2eT dedt
= 2eT (A+GC)e−2eT δAX . (40)
The rotor flux components can not be measured. The flux dynamic is faster than themachine parameters dynamic. Therefore, to simplify (40), we can accept that
Φαr = Φαr
Φβr = Φβr.(41)
ThuseT δAX =
Lm
bδω(Φβreiαs − Φαreiβs
)− 1
σLsδRs(iαseiαs + iβseiβs
). (42)
For the second and third terms of (39), we can write
2δωλ
dδωdt
= 2δωλ1
ddt
ω−2δωλ1
ddt
ω
2δRs
λ2
dδRs
dt= 2
δRs
λ2
ddt
Rs −2δRs
λ2
ddt
Rs.
(43)
We consider the hypothesis of a slowly varying regime for the machine parameters, thus:
dωdt
≈ 0
dRs
dt≈ 0,
(44)
10.2478/acsc-2013-0022
UnauthenticatedDownload Date | 1/19/18 1:34 AM
370 D. KOUCHIH, M. TADJINE, M.S. BOUCHERIT
thusdωdt
=dδωdt
dRs
dt=
dδRs
dt.
(45)
Finally, we obtain:
dVdt
= 2eT (A+GC)e− 2Lm
bδω(Φβreiαs − Φαreiβs
)(46)
+2
σLsδRs(iαseiαs + iβseiβs
)+2
δωλ1
ddt
ω+2δRs
λ2
ddt
Rs.
If the term dVdt = 2eT (A+GC)e is negative, the condition dV
dt < 0 is verified for:
2σLs
δRs(iαseiαs + iβseiβs
)− 2Lm
bδω(Φβreiαs − Φαreiβs
)(47)
+2δωλ1
ddt
ω+2δRs
λ2
ddt
Rs = 0.
This condition can be verified if:2
δωλ1
ddt
ω =2Lm
bδω(Φβreiαs − Φαreiβs
)2
δRs
λ2
ddt
Rs =− 2σLs
δRs(iαseiαs + iβseiβs
).
(48)
We obtain the adaptation mechanism in the form:ω =
∫λ1
Lm
b
(Φβreiαs − Φαreiβs
)dt
Rs =∫
−λ21
σLs
(iαseiαs + iβseiβs
)dt.
(49)
The matrix of gain G is selected such as the eigenvalues of the matrix A+GC are inthe left plane half of the complex plan and that the real part of the eigenvalues is largerin absolute value than the real part of the eigenvalues of the state matrix A [28].
The estimated electromagnetic torque is expressed as: We obtain the adaptationmechanism in the form:
Ce =32
pLm
Lr
(Φαr iβs − Φβr iαs
). (50)
The reference of the stator flux Φsn is deduced using the equation of the induction motorsteady-state model.
Vsn = ΦsnRs
Ls
√√√√√√(
1−σ LsLrRsRr
ωslωs
)2+(
LrRr
ωsl +LsRs
ωs
)2
1+(
σωslLrRr
)2 (51)
10.2478/acsc-2013-0022
UnauthenticatedDownload Date | 1/19/18 1:34 AM
IMPROVED DIRECT TORQUE CONTROL OF INDUCTION MOTORSUSING ADAPTIVE OBSERVER AND SLIDING MODE CONTROL 371
where ωsl is the rotor variables pulsation in nominal mode and Vsn is the nominal valueof the stator phase voltage.
4. Simulation results
The technique presented in the previous sections, has been implemented in the MAT-LAB environment. The IM parameters has been as follows: 3 [kW], 220/380 [V], 50[Hz], Rs = Rr = 1.84[Ω], Ls = Lr = 0.17 [H], Lm = 0.16 [H], J = 0.0145 [kgm2],fv = 0.0038 [Nms/rd].
4.1. Low speeds
To illustrate performances of the proposed control, we simulated a load-less startingup mode and nominal torque applied at time t = 0.3 [sec]. The synthesized observerallows us to reconstruct all the state variables. For the DTC simulation, torque and fluxhysteresis bands are 0.2 [Nm] and 0.01 [Wb] respectively. The load torque is fixed to 20[Nm]. The speed of reference equals to ±50 [rpm]. Figures 3-8 summarizes the controlsystem performance.
Figure 3. Observed and reference rotor speed. Figure 4. Observed electromagnetic torque.
4.2. High speed mode
The high speed mode depends on the machine and load mechanical possibilities.The load torque is an important factor for the choice of the acceptable high speed. Thehigh speed mode is important, particularly in the case of electrical vehicles, wherein, weadopt the weakening of stator flux – see figure 9.
We simulated a load-less starting up mode with a speed of reference equals to 1415[rpm]. Then at t = 0.5 [sec], we imposed a high speed of 2000 [rpm]. The simulationresults are shown in figures 10-12.
10.2478/acsc-2013-0022
UnauthenticatedDownload Date | 1/19/18 1:34 AM
372 D. KOUCHIH, M. TADJINE, M.S. BOUCHERIT
Figure 5. Effective value of the stator flux. Figure 6. The hodograph of the stator flux vector.
Figure 7. Direct and quadrature stator currents errors.
Figure 8. Observed stator resistance.
From the simulation results, we can estimate the machine variables in the differentworking from low to high speeds. It appears that the load torque and stator resistancevariations do not allocate the performances of the proposed control. The flux tracks thereference value and it is insensitive to parameters variation. The speed response also
10.2478/acsc-2013-0022
UnauthenticatedDownload Date | 1/19/18 1:34 AM
IMPROVED DIRECT TORQUE CONTROL OF INDUCTION MOTORSUSING ADAPTIVE OBSERVER AND SLIDING MODE CONTROL 373
Figure 9. Reference stator flux.
Figure 10. Observed and referenced rotor speed.
Figure 11. Effective value of the stator. Figure 12. The hodograph of the stator flux vector.
stays insensitive to parameters variation. The global control scheme introduces high per-formances of robustness, stability and precision, particularly, under uncertainties causedby parameter variation.
10.2478/acsc-2013-0022
UnauthenticatedDownload Date | 1/19/18 1:34 AM
374 D. KOUCHIH, M. TADJINE, M.S. BOUCHERIT
5. Conclusion
In this paper a new adaptive observer design method has been presented. The globalcontrol scheme introduces high performances of robustness. Stability and precision, par-ticularly, under uncertainties caused by load and stator resistance variation is also pre-served. Furthermore, this observation method presents a simple algorithm that has theadvantage to be easily implementable.
The adaptive observer uses an adaptive mechanism for the speed and the stator re-sistance estimation. This approach relies on the improvement of an estimation of thecomponents of the stator flux.
We can note that the estimation of the stator flux by the adaptive observer makes theIM based on DTC more robust if stability is concerned.
References
[1] I.TAKAHASHI and T. NOGUCHI: A new quick-response and high-efficiency con-trol strategy for an induction motor. IEEE Trans. on Industry Applications, 22(5),(1986), 820-827.
[2] M. DEPENBROCK: Direct self-control DSC of inverter fed induction machine.IEEE Trans. on Power Electronics, 3(4), (1988), 420-429.
[3] S. BELKACEM, F. NACERI, R. ABDESSEMED and B. KIYYOUR: Performanceanalysis of a speed sensorless induction motor drive based on DTC Scheme. Int. J.of Electrical and Power Engineering, 1(2), (2007), 158-164.
[4] M. MESSAOUDI, H. KRAIM, M.B. AHMED, L. SBITA and M.N. ABDELKRIM:A robust sensorless direct torque control of induction motor based on MRAS andextended Kalman filter. Leonardo J. of Sciences, 12(1), (2008), 35-56.
[5] K. SEDHURAMAN, S. HIMAVATHI and A. MUTHURAMALINGAM: Reactivepower based model reference neural learning adaptive system for speed estima-tion in sensor-less induction motor drives. The J. of Engineering Research, 9(2),(2011), 17-26.
[6] S. ALIRANI and V. JAGANNATHAN: Torque ripple minimization DTC based in-duction motor drive using fuzzy logic technique. Int. J. of Computing Applications,40(1), (2012), 25-31.
[7] M. AKTAS and H.I. OKUMUS: Stator resistance estimation using ANN in DTC IMDrives. Turkish J. of Electrical Engineering and Computer Sciences, 18(2), (2010),197-210.
10.2478/acsc-2013-0022
UnauthenticatedDownload Date | 1/19/18 1:34 AM
IMPROVED DIRECT TORQUE CONTROL OF INDUCTION MOTORSUSING ADAPTIVE OBSERVER AND SLIDING MODE CONTROL 375
[8] N. ALEKYA and B. MOHAN: Advanced technique to improve dynamic responseof a direct torque controlled induction motor. Int. J. of Scientific and ResearchPublications, 2(11), (2012), 1-6.
[9] H. KRAIEM, A. FLAH, M.B. HAMED and L. SBITA: High performances inductionmotor drive based on fuzzy logic control. Int. J. of Control and Automation, 5(1),(2012), 1-11.
[10] Y. BENSALEM, W. ABBOUD, L. SBITA and M.N. ABDELKRIM: A sensorlessneural network, Speed control of induction motor drive. Int. J. of Signal SystemControl and Engineering Application, 1(2), (2008), 150-158.
[11] M.H. KHAN, A. AZAM and J. AMARNATH: Fuzzy logic based MRAS speed ob-server for control of induction motor drive. World J. of Modelling and Simulation,6(2), (2010), 134-140.
[12] S. ABID, Y. RAMDANI and A.K. MEROFEL: Speed sliding mode control of sen-sorless induction machine. J. of Electrical Engineering, 57(1), (2006), 47-51.
[13] O. BARAMBONES, P. ALKORTA, A.J. GARRIDO and F.G. MESEDA: An adaptivesliding mode control scheme for induction motor drives. Int. J. of Circuits, Systemsand Signal Processing, 1(1), (2007), 73-77.
[14] W. SANGTUNGTONG: On improvement in the adaptive sliding-mode speed ob-server. WSEAS Trans. on Systems, 9(6), (2010), 581-593.
[15] P.Y. REDDY, C.H. KRISHNA and P.V. KISHORE: A new approach of DTC schemefor induction motor using flux mode observer. Int. J. of Engineering Research andApplications, 1(4), (2011), 1527-1535.
[16] X.Z. ZHANG and L. LI: A novel nonlinear controller design for induction motordrives based on sliding mode control and adaptive observer. J. of Electrical Sys-tems, 7(4), (2011), 382-393.
[17] B. TABBACHE, M.E.H BENBOUZID, A. KHELOUI and J.M. BOURGEOT: DSPbased sensor fault tolerant control of electric vehicle powertrains. In Proc. of the2011 IEEE Int. Symp. on Industrial Electronics, Gdansk, Poland, (2011), 2085-2090.
[18] A. ABBOU and H. MAHMOUDI: Performance of a sensorless direct torque fluxcontrol strategy for induction motors associated to the three levels NPC converterused in electric vehicles Int. J. of Sciences and Techniques of Automatic Control &Computer Engineering, 2(2), (2008), 790-803.
[19] D. KOUCHIH, M. TADJINE and M.S. BOUCHERIT: Analysis of controlled induc-tion motor drives with stator faults. In Proc. of Int. Symp. on Environment Friendly
10.2478/acsc-2013-0022
UnauthenticatedDownload Date | 1/19/18 1:34 AM
376 D. KOUCHIH, M. TADJINE, M.S. BOUCHERIT
Energies and Applications, Northumbria University, Newcastle upon Tyne, UnitedKingdom, (2012), 1-6.
[20] X. ZHANG and Y. WANG: Wavelet-neural-network based robust sliding-mode con-trol for induction motor. J. of Information & Computational Science, 8(7), (2011),1209-1216.
[21] I.F. JASIM: Stable robust adaptive control of induction motors with unknown pa-rameters. In Proc. of the 1st Int. Conf. on Energy, Power and Control, Universityof Baarah, Iraq, (2010), 145-150.
[22] Y.H. CHANG, C.I. WU, H.Y. LIN and N.D. KUO: Robust performance controlof vector-controlled induction motors with gain scheduled estimation and input-output linearization. Int. J. of Innovative Computing, Information and Control,7(1), (2011), 269-288.
[23] O. BENZINEB, H. SALHI, M. TADJINE, M.S. BOUCHERIT and M.E.H BEN-BOUZID: A PI/backstepping approach for induction motor drives robust control.Int. Review of Electrical Engineering, 5(2), (2010), 426-432.
[24] J.H. PUJAR and S.F. KODAD: Robust sensorless speed control of induction motorwith DTFC and fuzzy speed regulator. Int. J. of Electrical and Electronics Engi-neering, 5(1), (2011), 17-26.
[25] J.J.E. SLOTINE and W. LI: Applied Nonlinear Control. Prentice Hall Inc., Engle-wood Cliffs NJ, 1991.
[26] C. EDWARDS and S.K. SPURGEON: Sliding Mode Control, Theory and Applica-tions. The Taylor & Francis Systems and Control Book Series, 1998.
[27] P.C. KRAUSE: Analysis of Electric Machinery. McGraw-Hill Book Company,1987.
[28] D.G. LUENBERGER: An introduction to observers. IEEE Trans. on AutomaticControl, 16(6), (1971), 596-602.
10.2478/acsc-2013-0022
UnauthenticatedDownload Date | 1/19/18 1:34 AM