What Cisco tool can be used to monitor events happening in the switch?Embedded Event ManagerIntrusion Prevention SystemNetwork Analysis moduleSwitched Port AnalyzerA port can act as the destination port for all SPAN sessions configured on the switch.A port can be configured to act as a source and destination port for a single SPAN session.Both Layer 2 and Layer 3 switched ports can be configured as source or destination ports for a single SPAN session.Port channel interfaces (EtherChannel) can be configured as source and destination ports for a single SPAN session.

Which configuration guideline applies to using the capture option in VACL?Capture ports transmit traffic that belongs to all VLANs.The capture port captures all packets that are received on the port.The switch has a restriction on the number of capture ports.The capture port needs to be in the spanning-tree forwarding state for the VLAN

What technology can be used to help mitigate MAC address flooding attacks?

root guard

Private VLANs

DHCP snooping

VLAN access maps

Dynamic ARP Inspection

What Cisco tool can be used to monitor events happening in the switch?Embedded Event ManagerIntrusion Prevention SystemNetwork Analysis moduleSwitched Port Analyzer

What advantage for monitoring traffic flows does using VACLs with the capture option offer over using SPAN?

VLAN ACLs can be used to capture denied traffic.

VLAN ACLs can be used to capture traffic on a spanning-tree blocked port.

VLAN ACLs can be used to capture traffic based on Layer 2, 3, or 4 information.

VLAN ACLs can be used to capture traffic to the CPU separate from the traffic that is

hardware switched.

All access ports on a switch are configured with the administrative mode of dynamic auto. An attacker, connected to one of the ports, sends a malicious DTP frame. What is the intent of the attacker?

VLAN hoppingDHCP spoofing attackMAC flooding attackARP poisoning attack

What is the function of the 6500 Network Analysis Module?

monitors traffic on ingress ports sends TCP resets to an attacker TCP session

gathers multilayer information from data flows that pass through the switch provides remote monitoring of multiple switches across a switched network

Refer to the exhibit. What is the state of the monitoring session?

This is a remote monitored session.

No data is being sent from the session.

SPAN session number 2 is being used.

The session is only monitoring data sent out Fa0/1.

Refer to the exhibit. After the configuration has been applied to ACSw22, frames that are bound for the node on port FastEthernet 0/1 are periodically being dropped. What should be done to correct the issue?

Add the switchport port-security mac-address sticky command to the interface configuration.

Change the port speed to speed auto with the interface configuration mode.

Use the switchport mode trunk command in the interface configuration

Remove the switchport command from the interface configuration.

What are two purposes for an attacker launching a MAC table flood? (Choose two.)to initiate a man-in-the-middle attackto initiate a denial of service (DoS) attackto capture data from the network

to gather network topology informationto exhaust the address space available to the DHCP

What is one way to mitigate ARP spoofing?Enable dynamic ARP inspection.Configure MAC address VLAN access maps.Enable root guard.Implement private VLANs.

What is one way to mitigate spanning-tree compromises?Statically configure the primary and backup root bridge.Implement private VLANs.Place all unused ports into a common VLAN (not VLAN 1).Configure MAC address VLAN access maps.

Refer to the exhibit. A switch is being configured to support AAA authentication on the console connection. Given the information in the exhibit, which three statements are correct? (Choose three.)

The authentication login admin line console command is required.

The login authentication admin line console command is required.

The configuration creates an authentication list that uses a named access list called group as the first authentication method, a TACACS+ server as the second method, the local username database as the third method, the enable password as the fourth method, and none as the last method.

The configuration creates an authentication list that uses a TACACS+ server as the first authentication method, the local username database as the second method, the enable password as the third method, and none as the last method.

The none keyword enables any user logging in to successfully authenticate if all other methods return an error.

The none keyword specifies that a user cannot log in if all other methods have failed.

Refer to the exhibit. Network policy dictates that security functions should be administered using AAA. Which configuration would create a default login authentication list that uses RADIUS as the first authentication method, the enable password as the second method, and the local database as the final method?

SW-1(config)# aaa new-model SW-1(config)# radius-server host 10.10.10.12 key secret

SW-1(config)# aaa authentication default group-radius local

SW-1(config)# aaa new-model SW-1(config)# radius-server host 10.10.10.12 key secret SW-1(config)# aaa authentication default group-radius enable local

SW-1(config)# aaa new-model SW-1(config)# radius-server host 10.10.10.12 key secret SW-1(config)# aaa authentication login default group radius enable local

SW-1(config)# aaa new-model SW-1(config)# radius server host 10.10.10.12 key secret SW-1(config)# aaa authentication login default group radius enable local none

SW-1(config)# aaa new-model SW-1(config)# radius server host 10.10.10.12 key secret SW-1(config)# aaa authentication login default group-radius enable local none

Refer to the exhibit. Given the configuration on the ALSwitch, what is the end result?

forces all hosts that are attached to a port to authenticate before being allowed

access to the network disables 802.1x port-based authentication and causes the port

to allow normal traffic without authenticating the client enables 802.1x authentication

on the port globally disables 802.1x authentication

How should unused ports on a switch be configured in order to prevent VLAN hopping attacks?

Configure them with the UDLD feature.Configure them with the PAgP protocol.Configure them as trunk ports for the native VLAN 1.Configure them as access ports and associate them with an unused VLAN.

Which countermeasure can be implemented to determine the validity of an ARP packet, based on the valid MAC-address-to-IP address bindings stored in a DHCP snooping database?

DHCP spoofingdynamic ARP inspectionCAM table inspectionMAC snooping

Refer to the exhibit. A network engineer is securing a network against DHCP spoofing attacks. On all switches, the engineer applied the ip dhcp snooping command and enabled DHCP snooping on all VLANs with the ip dhcp snooping vlan command. What additional step should be taken to configure the security required on the network?

Issue the ip dhcp snooping trust command on all uplink interfaces on SW1, SW2 and

SW3. Issue the ip dhcp snooping trust command on all interfaces on SW2 and SW3.

Issue the ip dhcp snooping trust command on all interfaces on SW1, SW2, and SW3.

Issue the ip dhcp snooping trust command on all interfaces on SW1, SW2, and SW3 except interface Fa0/1 on SW1.

Refer to the exhibit. Which statement is true about the local SPAN configuration on switch SW1?

The SPAN session transmits to a device on port Fa3/21 a copy of all traffic that is monitored on port Fa3/1.

The SPAN session transmits to a device on port Fa3/21 a copy of all traffic that is monitored on port Fa3/1, but only if port Fa3/1 is configured in VLAN 10.

The SPAN session transmits to a device on port Fa3/21 a copy of all traffic that is monitored on port Fa3/1, but only if port Fa3/1 is configured as trunk.

The SPAN session transmits to a device on port Fa3/21 only a copy of unicast traffic that is monitored on port Fa3/1. All multicast and BPDU frames will be excluded from the monitoring process.