imanager m2000
TRANSCRIPT
-
8/10/2019 IManager M2000
1/38
Function Description
Function Description of M2000FOR WIMAX
Note:This is an informal function description. It is used for bidding before
the TR5 point. The function list is determined by the OM department ofproduct management , and edited by the OM marketing supportdepartment.
Because this document is only used for market support, it will bereplaced with the formal document later on.
Issue 1.3
Date 2008-11-03
CONFIDENTIAL
Huawei Technologies Co., Ltd.
-
8/10/2019 IManager M2000
2/38
FOR INTERNAL USE ONLY
Function Description of M2000 for WiMAX
Function Description
Issue 1.10 (2008-11-03) Huawei Technologies Proprietary Page 2 of 38
Huawei Technologies Co., Ltd. provides customers with comprehensive technical support and service. Pleasefeel free to contact our local office or company headquarters.
Huawei Technologies Co., Ltd.
Address: Administration Building, Huawei Technologies Co., Ltd.,
Bantian, Longgang District, Shenzhen, 518129, Peoples Republic of China
Website: http://www.huawei.com
Telephone: 0755-28560000 8008302118
Fax: 0755-28560111
Email: [email protected]
Copyright Huawei Technologies Co., Ltd. 2006. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any means without priorwritten consent of Huawei Technologies Co., Ltd.
Trademarks and Permissions
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective holders.
NoticeThe information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, andrecommendations in this document do not constitute the warranty of any kind, express or implied.
http://www.huawei.com/mailto:[email protected]:[email protected]://www.huawei.com/ -
8/10/2019 IManager M2000
3/38
FOR INTERNAL USE ONLY
Function Description of M2000 for WiMAX
Function Description
Issue 1.10 (2008-11-03) Huawei Technologies Proprietary Page 3 of 38
About This Document
Author
Name Chen Zhihui Date 2007-4-17
Reviewed by Xiao Yong, Chen Ting Date 2007-4-17
Approvedby
Date
IntroductionThis document is a general introduction to the functions provided by the Huawei M2000
FOR WIMAX. It aims to help readers better understand M2000 functions and features.
The table below lists the main chapters of this document.
Chapter Description
Chapter 1 Overview Specifies the associated versions of this
document and lists all the referred networkelements.
Chapter 2 Basic Functions Describes all the basic functions of the M2000FOR WIMAX.
Chapter 3 Optional Functions Describes all the optional functions of theM2000 FOR WIMAX.
-
8/10/2019 IManager M2000
4/38
FOR INTERNAL USE ONLY
Function Description of M2000 for WiMAX
Function Description
Issue 1.10 (2008-11-03) Huawei Technologies Proprietary Page 4 of 38
Table of Contents
1 Overview................................................................................................................................... 7
2 Basic Functions....................................................................................................................... 12
2.1 Fault Management..................................................................................... ...............................................12
2.2 Configuration Management ......................................................................................................................18
2.3 Performance Management ........................................................................................................................20
2.4 Security Management............................................................................................................................... 23
2.5 Log Management......................................................................................................................................26
2.6 Topology Management .............................................................................................................................28
2.7 System Management ................................................................................................................................29
2.8 System Reliability ....................................................................................................................................31
3 Optional Functions ................................................................................................................ 33
3.1 Customization Performance Report System...............................................................................................33
3.2 Northbound Interface To NMS..................................................................................................................33
3.3 NE Software Management........................................................................................................................36
3.4 Alarm Remote Notification....................................................................................................................... 37
3.5 HA System............................................................................................................................................... 37
3.6 Support Vector Map on Topology..............................................................................................................38
3.7 Bulk Configuration................................................................................................ "#$%&'(40
3.8 HA System (Remote Backup) ...................................................................................................................41
3.9 Script Automatic Tool...............................................................................................................................42
3.10 Graphic Configuration of WRAN NEs ................................................................. "#$%&'(43
-
8/10/2019 IManager M2000
5/38
FOR INTERNAL USE ONLY
Function Description of M2000 for WiMAX
Function Description
Issue 1.10 (2008-11-03) Huawei Technologies Proprietary Page 5 of 38
-
8/10/2019 IManager M2000
6/38
FOR INTERNAL USE ONLY
Function Description of M2000 for WiMAX
Function Description
Issue 1.10 (2008-11-03) Huawei Technologies Proprietary Page 6 of 38
Tables
Table 1-1Function table ..................................................................................................................................7
Table 2-1Types of logs................................................................................... ...............................................26
Table 3-1Centralized management on the SGSN, and the GGSN............................. ......................................35
-
8/10/2019 IManager M2000
7/38
FOR INTERNAL USE ONLY
Function Description of M2000 for WiMAX
Function Description
Issue 1.10 (2008-11-03) Huawei Technologies Proprietary Page 7 of 38
1 OverviewThis text aims to help readers better understand M2000 functions and features. For a briefintroduction, please refer toFunction List of M2000.
This document is a brief list of the functions provided by the Huawei M2000 for WiMAX.The document is intended as a general introduction to the M2000 for WiMAX functions.
The network element (NE) in this document refers to the mobile communication equipmentmanaged by the M2000. The M2000 can manage WiMAX NEs and IP devices.
The M2000 can manage the following WiMAX NEs:
l Base station: BS
l Access gateway: ASN-GW
l Authentication server: AAA
The M2000 can manage the following IP devices:
l Lanswitches of the S series
l NE08 Series, AR28/AR46 Series Routers
l Eudemon Series Firewalls
l IP devices from the third party, such as switches, firewalls, and other NEs having theSNMP interfaces
Table 1-1Function table
Index Function Name Node Function ID
Fault Management Centralized Storage of Alarm Information ALL WOFD-010100
Alarm Export ALL WOFD-010200
Real Time Alarm Browse ALL WOFD-010300
Alarm Query ALL WOFD-010400
Alarm Topology Indication ALL WOFD-010500
Alarm Box ALL WOFD-010600
Alarm Information Storage ALL WOFD-010700
Alarm Printing ALL WOFD-010800
-
8/10/2019 IManager M2000
8/38
FOR INTERNAL USE ONLY
Function Description of M2000 for WiMAX
Function Description
Issue 1.10 (2008-11-03) Huawei Technologies Proprietary Page 8 of 38
Index Function Name Node Function ID
Alarm Detailed Information Browse ALL WOFD-010900
Filter Condition Template ALL WOFD-011000
Customized Alarm Field Display ALL WOFD-011100
Customized Alarm Color ALL WOFD-011200
Alarm Topology Location ALL WOFD-011300
Alarm Auto Synchronization ASN-GWBS WOFD-011400
Alarm Manual Synchronization ALL WOFD-011500
Alarm Periodic Synchronization ALL WOFD-011600
Alarm Acknowledge ALL WOFD-011700
Alarm De-acknowledge ALL WOFD-011800
Alarm Manual Clear ASN-GWBS WOFD-011900
Alarm Auto Clear ALL WOFD-012000
EMS Severity Level Redefinition ALL WOFD-012100
NE Severity Level Redefinition ASN-GW WOFD-012200
EMS Alarm Shield ALL WOFD-012300
NE Alarm Shield ASN-GW WOFD-012400
Alarm Statistics ALL WOFD-012500
Real Time Alarm Statistics ALL WOFD-012600
Alarm Panel ALL WOFD-012700
Real Time Alarm Printing ALL WOFD-012800
Alarm Knowledge Base ALL WOFD-012900
Long Time Un-cleared Fault AlarmIndication
ALL WOFD-013200
IP Device Alarm Management Lanswitch Series,NE08 Series,AR28/AR46 Series,Eudemon Series, IP
devices from thethird-party
WOFD-013500
Alarm Remark ALL WOFD-013600
ConfigurationManagement
Configuration Data Auto Synchronization ASN-GW WOFD-020100
Configuration Data Manual Synchronization ASN-GWAAA WOFD-020200
-
8/10/2019 IManager M2000
9/38
FOR INTERNAL USE ONLY
Function Description of M2000 for WiMAX
Function Description
Issue 1.10 (2008-11-03) Huawei Technologies Proprietary Page 9 of 38
Index Function Name Node Function ID
Configuration Data SynchronizationPeriodically
ASN-GWAAA WOFD-020300
Configuration Data Query ALL WOFD-020400
Configuration Data Export ASN-GWAAA WOFD-020500
NE Bulk Creation ALL WOFD-020600
NE Bulk Deletion ALL WOFD-020700
Equipment Panel ASN-GW WOFD-021000
Interface tracing ASN-GWBS WOFD-021100
PerformanceManagement
Performance Measurement Data Collectionand Storage
ALL WOFD-030100
Short Period Performance MeasurementManagement
ASN-GWAAA WOFD-030200
Performance Measurement InformationView
ALL WOFD-030300
Performance Data Export ALL WOFD-030400
Performance Measurement Data Query ALL WOFD-030500
Performance Measurement Data Printing ALL WOFD-030600
Performance Measurement Data Storage ALL WOFD-030700
Performance Measurement DataSynchronization
BSASN-GW WOFD-030800
Performance Measurement Data Browse ALL WOFD-030900
Customizable Counter Management ALL WOFD-031000
Performance Measurement Data QueryTemplate
ALL WOFD-031100
Threshold Alarm ALL WOFD-031200
SecurityManagement
Centralized Management of Users and UserGroups
ALL (The BS and the
AAA do not supportcentralizedmanagement of theNE users)
WOFD-040100
Centralized User Authentication ALL (The BS and the
AAA do not supportcentralized userauthentication)
WOFD-040200
Security Policy ALL WOFD-040300
Terminal Auto Locking ALL WOFD-040400
-
8/10/2019 IManager M2000
10/38
FOR INTERNAL USE ONLY
Function Description of M2000 for WiMAX
Function Description
Issue 1.10 (2008-11-03) Huawei Technologies Proprietary Page 10 of 38
Index Function Name Node Function ID
EMS User Online Monitoring ALL WOFD-040500
NE User Online Monitoring ASN-GW WOFD-040700
Log Management EMS Log Record M2000 WOFD-050100
EMS Log Query M2000 WOFD-050200
Log Printing M2000ASN-GW WOFD-050300
Log Saving M2000ASN-GW WOFD-050400
Log Export M2000ASN-GW WOFD-050500
NE Log Query ASN-GW WOFD-050600
Log Statistic M2000ASN-GW WOFD-050700
TopologyManagement
Topology Object Management ALL WOFD-060100
Topology Navigation ALL WOFD-060300
Topology Map Management ALL WOFD-060400
Topology Object Searching and Locating ALL WOFD-060500
SystemManagement
Local Maintenance Agent ASN-GW WOFD-070100
Centralized MML ASN-GW WOFD-070200
System Monitoring ALL WOFD-070600
Online Help ALL WOFD-070700
Time Synchronization ASN-GW WOFD-070800
Daylight Saving Time, multiple time zonesmanagement
ASN-GW WOFD-070900
EMS License management M2000 WOFD-071000
System Reliability Disk Redundant Backup M2000 WOFD-080100
EMS Backup and Restore ALL WOFD-080300
NE Data Backup and Restore ASN-GW WOFD-080400
Customization
PerformanceReport System
Customization Performance Report System ALL WOFD-090100
NorthboundInterface to NMS
CORBA Alarm Interface ALL WOFD-100110
File Alarm Data Interface ALL WOFD-100210
File Performance Data Interface ALL WOFD-100220
-
8/10/2019 IManager M2000
11/38
FOR INTERNAL USE ONLY
Function Description of M2000 for WiMAX
Function Description
Issue 1.10 (2008-11-03) Huawei Technologies Proprietary Page 11 of 38
Index Function Name Node Function ID
File Configuration Data Interface ALL WOFD-100230
Alarm Streaming Interface ALL WOFD-100400
SNMP Alarm Interface ALL WOFD-100500
NE SoftwareManagement
NE Software Management BSASN-GW WOFD-110100
Alarm RemoteNotification
Alarm Remote Notification ALL WOFD-120100
HA System HA System M2000 WOFD-130100
Support VectorMap on Topology
Support Vector Map on Topology M2000 WOFD-140100
Comments: TheALL in the specified columnNode of above table refers to WCDMA NEs not including IP devices listed at the
beginning of this document.
-
8/10/2019 IManager M2000
12/38
FOR INTERNAL USE ONLY
Function Description of M2000 for WiMAX
Function Description
Issue 1.10 (2008-11-03) Huawei Technologies Proprietary Page 12 of 38
2 Basic Functions2.1 Fault Management
WOFD-010100
Function: Centralized Storage of Alarm Information
Description:
The system collects alarms from the managed NEs and itself and stores them in the alarmdatabase. The alarms can be divided into fault alarm and event alarm. Fault alarm can bedivided into current alarm and history alarm. A fault alarm is generated upon equipment
failure. When the fault disappears, the alarm status is set to be cleared. The event alarmnotifies the user the event happened to the NE. An event alarm cannot be cleared. The currentalarm is a fault alarm not recovered yet. The history alarm is a fault alarm recovered and
acknowledged.
WOFD-010200
Function: Alarm Export
Description:
The Alarm Exportfunction exports the alarms from the database to the file regularly. The
file supports the following formats:
l XML
l HTML
The system supports the Latest Data ExportandEarliest Data Export.
Latest Data Export: export the alarm data collected in a recent period to a file for theanalysis of other systems and users. The file that saves the exported data is located in thedefault path of the server. The condition to be set includesTime.
Earliest Data Export: Export the alarm data that exceeding the predefined threshold to a fileand delete the records related to the alarms from the database to protect the database. The filethat saves the exported data is located in the default path of the server. The condition to be set
includesSaving Days. The data that exceeds the range of Saving Daysis exported anddeleted.
-
8/10/2019 IManager M2000
13/38
FOR INTERNAL USE ONLY
Function Description of M2000 for WiMAX
Function Description
Issue 1.10 (2008-11-03) Huawei Technologies Proprietary Page 13 of 38
TheAlarm Exportfunction is realized when the Centralized Task Managementfunction is
enabled.
WOFD-010300
Function: Real-time Alarm Browse
Description:
The Real-time Alarm Browse function displays alarm information in real time in alarm
browse window. Displayed alarms can be customized according to filter conditions. Multiplebrowse windows can be opened at the same time, each with a different condition group.
Supported conditions for the alarms are: NE, alarm severity, alarm category, alarm name andtime segment.
WOFD-010400
Function: Alarm Query
Description:
The Alarm Query function enables users to query alarms according to specified filterconditions. Supported filter conditions are: NE, alarm severity, alarm category, alarm name,time segment and alarm status.
The operation can be started from the topology GUI.
WOFD-010500
Function: Alarm Topology Indication
Description:
The Alarm Topology Indication function displays the alarm status of NEs on topology GUI. Ifa NE has current fault alarms, a tiny alarm icon is displayed on the icon of this NE. The colorof the icon is the color of the highest severity alarm.
WOFD-010600
Function: Alarm Box
Description:
The Alarm Box function presents alarms audibly and visibly.
An alarm box is connected to an alarm terminal. The alarm terminal sends alarms to the alarmbox according to specified conditions. Supported conditions are: NE and alarm severity.
WOFD-010700
Function: Alarm Information Storage
Description:
The Alarm Information Storage function enables users to save the alarms in alarm querywindow to files. Supported file types are: TXT, HTML and CSV.
All alarms or selected alarms can be saved.
-
8/10/2019 IManager M2000
14/38
FOR INTERNAL USE ONLY
Function Description of M2000 for WiMAX
Function Description
Issue 1.10 (2008-11-03) Huawei Technologies Proprietary Page 14 of 38
WOFD-010800
Function: Alarm Printing
Description:
The Alarm Printing function enables users to print alarm information from alarm query
windows.
All alarms or selected alarms can be printed.
WOFD-010900
Function: Alarm Detailed Information Browse
Description:
The Alarm Detailed Information Browse function enables users to view the detailed alarminformation in alarm query window and browse window. The detailed information includes
recovery suggestion, location and knowledge base.
WOFD-011000
Function: Filter Condition Template
Description:
The Filter Condition Template function enables users to save the alarm query filter conditions
and alarm real-time browse condition as templates. The templates are stored by user. Whenusers use a template to browse or query alarms, users do not need to specify the displayconditions. The system displays the alarms according to the conditions of the template.
WOFD-011100
Function: Customized Alarm Field Display
Description:
The Customized Alarm Field Display function enables users to customize the alarm fieldcolumn in the alarm query window and real-time browse window.
The customization only affects the current terminal.
WOFD-011200
Function: Customized Alarm Color
Description:
The Customized Alarm Color function enables users to customize the colors of alarms ofdifferent severity and different status. The color setting is applicable to alarm browse window,alarm query window, alarm panel and topology map.
WOFD-011300
Function: Alarm Topology Location
Description:
-
8/10/2019 IManager M2000
15/38
FOR INTERNAL USE ONLY
Function Description of M2000 for WiMAX
Function Description
Issue 1.10 (2008-11-03) Huawei Technologies Proprietary Page 15 of 38
The Alarm Topology Location function enables users to locate the NE in the topological map
from an alarm in the alarm query window or real-time browse window.
WOFD-011400
Function: Alarm Auto Synchronization
Description:
TheAlarm Auto Synchronizationfunction ensures alarm consistency between the system
and NEs.
When the connection between the system and a NE recovers, the system automatically
synchronizes with the NEs to get the alarms generated during disconnection.
Upon receiving an alarm, the system compares it with previously received alarms to check if
there exists inconsistency. If the alarms on the two sides are inconsistent, the system re-getsthe missing alarms.
WOFD-011500
Function: Alarm Manual Synchronization
Description:
The Alarm Manual Synchronizationfunction enables users to start synchronization of thealarms between the system and the NEs.
WOFD-011600
Function: Alarm Periodic Synchronization
Description:
The Alarm Periodic Synchronization function periodically starts alarm synchronizationbetween the system and NEs. The duration between two synchronizations is one day.
WOFD-011700
Function: Alarm Acknowledge
Description:
TheAlarm Acknowledgefunction enables users to acknowledge alarms. After the operation,
the alarm status changes to acknowledged. The system records the user and time ofacknowledge.
The system supports manual acknowledge and automatic acknowledge.
Manual Acknowledgesupports users to manually acknowledge alarms.
Automatic Acknowledgesupports users to set filter conditions. The system automatically
checks the conditions and acknowledges those satisfied alarms.
WOFD-011800
Function: Alarm Unacknowledge
Description:
-
8/10/2019 IManager M2000
16/38
FOR INTERNAL USE ONLY
Function Description of M2000 for WiMAX
Function Description
Issue 1.10 (2008-11-03) Huawei Technologies Proprietary Page 16 of 38
The Alarm Unacknowledgefunction enables users to unacknowledge the acknowledged
alarms. When an acknowledged alarm is unacknowledged, its status is changed tounacknowledged.
WOFD-011900Function: Alarm Manual Clear
Description:
The Alarm Manual Clearfunction enables users to manually clear alarms. When an alarm iscleared, its status is changed to cleared. The system then sends a command to thecorresponding NE to change its status on the NE to cleared.
WOFD-012000
Function: Alarm Auto Clear
Description:
When a NE finds a fault recovered, the NE generates a clear alarm and sends it to the system.On reception, the system changes the alarm status to cleared.
WOFD-012100
Function: EMS Severity Level Redefinition
Description:
The EMS Severity Level Redefinitionfunction enables users to change the alarm severity onthe system. After redefinition, the system displays alarms according to the new severity
definition. The severity definition on the NEs keeps unchanged.
WOFD-012200
Function: NE Severity Level Redefinition
Description:
The NESeverity Level Redefinitionfunction enables users to change the alarm severity on
an NE. After the severity level is redefined, the NE reports the alarm based on the newseverity level and the EMS displays the alarm based on the new severity level.
WOFD-012300Function: EMS Alarm Shield
Description:
The EMS Alarm Shieldfunction enables users to shield alarms on EMS side. When an NEreports an alarm that satisfies the shielding conditions, the system just discards the alarm.
Supported conditions are: NE, alarm severity level, alarm name, alarm category and timeperiod.
WOFD-012400
Function: NE Alarm Shield
-
8/10/2019 IManager M2000
17/38
FOR INTERNAL USE ONLY
Function Description of M2000 for WiMAX
Function Description
Issue 1.10 (2008-11-03) Huawei Technologies Proprietary Page 17 of 38
Description:
The NE Alarm Shield function enables users to shield alarm on the NE side. Then the NEwill not send alarms that satisfy the shielding conditions. Supported condition is: alarm name.
WOFD-012500
Function: Alarm Statistics
Description:
TheAlarm Statisticsfunction enables users to statistic alarms from multiple dimensions.With this function, users will have a comprehensive overview of alarm distribution status of
the whole network. The statistical results can be shown in tables or pie charts.
Supported dimensions are: NE, NE type, alarm name, alarm severity level, alarm category,
alarm status and time.
WOFD-012600
Function: Real-time Alarm Statistics
Description:
The Real-time Alarm Statistics function enables users to statistic un-cleared fault alarms of
each NE. The statistical results will be refreshed in real time along with the generation andclearance of the alarms. The results are classified to display according to different alarmseverity levels.
WOFD-012700
Function: Alarm Panel
Description:
The system makes statistics on fault alarms in real time and classify the results by status andalarm severity level. The results are displayed in the alarm panel.
The alarm panel reminds users using customized alert tone and flickering icons.
WOFD-012800
Function: Real-time Alarm Printing
Description:
The Real-time Alarm Printingfunction prints alarm information in real time. All the alarmsaccording to specified conditions are printed.
Supported conditions are: NE, alarm severity level, alarm category, alarm name and timeperiod.
WOFD-012900
Function: Alarm Knowledge Base
Description:
-
8/10/2019 IManager M2000
18/38
FOR INTERNAL USE ONLY
Function Description of M2000 for WiMAX
Function Description
Issue 1.10 (2008-11-03) Huawei Technologies Proprietary Page 18 of 38
The Alarm Knowledge Basefunction enables users to record experience of handling faults
into the knowledge base.
The alarm knowledge base supports import and export operations.
WOFD-013200
Function: Long Time Un-cleared Fault Alarm Indication
Description:
The system auto detects un-cleared fault alarms that have lasted for a long period, and thenprompts users by highlighting these alarms on the alarm windows.
The period can be customized.
WOFD-013500
Function: IP Device Alarm Management
Description:
The EMS manages the IP networking devices in the network in an integrated manner. Inaddition, the EMS collects and displays alarms.
The IP networking devices consist of the following:
l Router
l Lanswitch
l Firewall
l Third-party NEs with SNMP alarm interface
WOFD-013600
Function: Alarm Remark
Description:
The Alarm Remark function allows users to add remark information on alarms. The remarkinformation includes history operations performed on an alarm, operators, operation time, and
remarks. An alarm supports remark information of not more than 4,096 bytes.
2.2 Configuration Management
WOFD-020100
Function: Configuration Data Auto Synchronization
Description:
The Configuration Data Auto Synchronizationfunction ensures configuration data keepconsistent. When the configuration data on a NE changes, the NE will send a notification toreport the change. The system then updates its database.
-
8/10/2019 IManager M2000
19/38
FOR INTERNAL USE ONLY
Function Description of M2000 for WiMAX
Function Description
Issue 1.10 (2008-11-03) Huawei Technologies Proprietary Page 19 of 38
WOFD-020200
Function: Configuration Data Manual Synchronization
Description:
The Configuration Data Manual Synchronizationfunction enables users to start
synchronous operation manually. The system will re-collect data from NE and refreshconfiguration data in database.
WOFD-020300
Function: Configuration Data Periodic Synchronization
Description:
The Configuration Data Periodic Synchronizationfunction supports periodicsynchronization of the NE configuration data according to user-defined conditions.
Supported conditions are: synchronization time intervals and start time.
The synchronization time interval can be set by hour or day. It must be integral times of an
hour or day. The maximum interval is 365 days, and the minimum interval is one hour.
WOFD-020400
Function: Configuration Data Query
Description:
The Configuration Data Queryfunction enables users to browse the configuration data of
managed NEs .
The BS can only query the following information:
l Carrier ID
l Carrier status
WOFD-020500
Function: Configuration Data Export
Description:
The Configuration Data Exportfunction supports automatically exports configuration datato files according to pre-defined conditions.
Supported file formats are: CSV and XML.
Supported conditions are: export period and NE.
The data exported through the periodic export can only be saved to files of the XML format,while the manual export supports both the CSV and XML formats.
WOFD-020600
Function: NE Bulk Creation
Description:
-
8/10/2019 IManager M2000
20/38
FOR INTERNAL USE ONLY
Function Description of M2000 for WiMAX
Function Description
Issue 1.10 (2008-11-03) Huawei Technologies Proprietary Page 20 of 38
The NE Bulk Creationfunction supports NE bulk creation from script files.
WOFD-020700
Function: NE Bulk Deletion
Description:
The NE Bulk Deletionfunction supports bulk deleting selected NEs from the topology GUI.
WOFD-021000
Function:Equipment Panel
Description:
System provides equipment panel of network element, showing information of rack and board,alarms and status will directly be shown in equipment panel, user also can do some operations
such as reset board etc.
Operator has a more intuitionist topology to inspect status of hardware.
WOFD-021100
Function:Interface Tracing
Description:
System provides Interface Tracingfunction, include tracing Signaling Message and Singlesubscriber Signaling Message, the message can be saved in tmf format or txt format, systemalso supports online or offline browsing traced message.
By tracing interfaces and signaling links, you can perform data check and troubleshooting
Operator can get more detail information according to the tracing function.
2.3 Performance Management
WOFD-030100
Function: Performance Measurement Data Collection and Storage
Description:
The system centralizes the collection of network measurement data and stores the data indatabase.
There are two kinds of measurement counters: Default Counter and Extended Counter.
The Default Counters are collected and stored by default by the system. Users can configure
the measured objects.
The Extended Counters are configured by users. Users can configure the extended counter
according to measured objects and counters.
The Default Counter and Extended Counter support 30 minute period, 60 minute period and
1440 minute period.
-
8/10/2019 IManager M2000
21/38
FOR INTERNAL USE ONLY
Function Description of M2000 for WiMAX
Function Description
Issue 1.10 (2008-11-03) Huawei Technologies Proprietary Page 21 of 38
The BS supports only the 30-minute period.
The performance measurement can be suspended and resumed, the suspended performance
measurement will not produce the performance data.
WOFD-030200
Function: Short Period Performance Measurement Management
Description:
The Short Period Performance Measurement Managementfunction supports shorter
granularity period collection of performance data. Users can configure the object andperformance counter of data with short period.
The period of short period performance data collection is five minutes or fifteen minutes.
WOFD-030300
Function: Performance Measurement Information View
Description:
The Performance Measurement Information Viewfunction enables users to view detailed
information of performance data.
The information includes: measured objects, measurement counter and the counter status, the
statistic period, and so on.
WOFD-030400Function: Performance Data Export
Description:
The Performance Data Export exports the performance data from the database into a file
periodically. The file can be either in .xml format or in .csv format.
The system supports the Latest Data ExportandEarliest Data Export.
Latest Data Export: exports the performance data collected in a recent period into a file forthe analysis of other systems and users. The file that saves the exported data is located in the
default path of the server. The conditions to be set includeTime and Function Subset.
Earliest Data Export: exports the performance data that exceeding the predefined threshold
into a file, and deletes the alarm-related records from the database to protect the database. Thefile that saves the exported data is located in the default path of the server. The condition to beset includesSaving Days. The data that exceeds the range of Saving Daysis exported anddeleted.
ThePerformance Data Exportis realized when the Centralized Task Managementfunction is enabled.
WOFD-030500
Function: Performance Measurement Data Query
-
8/10/2019 IManager M2000
22/38
FOR INTERNAL USE ONLY
Function Description of M2000 for WiMAX
Function Description
Issue 1.10 (2008-11-03) Huawei Technologies Proprietary Page 22 of 38
Description:
The Performance Measurement Data Queryfunction enables users to query measurementdata by conditions. Supported conditions are: measured object, time range and every
measurement counter.
The queried data can be displayed in tables, line charts and column charts. The line charts
supports the comparative displays of !one object, multi counters"and !one counter, multiobjects".
WOFD-030600
Function: Performance Measurement Data Printing
Description:
The Performance Measurement DataPrintingfunction enables users to print performancemeasurement data in the query window.
All data or selected data can be printed.
WOFD-030700
Function: Performance Measurement Data Storage
Description:
The Performance Measurement Data Storagefunction enables the measured data in the
query window to be saved as files. Supported files are: TXT, HTML and CSV.
The line charts and the column charts in the query window can be saved as pictures. The
picture formats are BMP and JPEG.
WOFD-030800
Function: PerformanceMeasurement Data Synchronization
Description:
The Performance Measurement Data Synchronizationfunction ensures the consistency of
performance data between the system and NEs.
The system supports manually and automatically synchronization.
WOFD-030900Function: Performance Measurement Data Browse
Description:
The Performance Measurement Data Browsefunction enables users to browse theperformance data of measurement units.
Data of new period that meets the conditions are displayed in the performance data browsewindow in real-time. The system supports multiple performance data browse windows at the
same time.
-
8/10/2019 IManager M2000
23/38
FOR INTERNAL USE ONLY
Function Description of M2000 for WiMAX
Function Description
Issue 1.10 (2008-11-03) Huawei Technologies Proprietary Page 23 of 38
WOFD-031000
Function: Customizable Counter Management
Description:
The Customizable Counter Managementfunction enables users to define new counters on
the basis of the counters provided by the system. The supported arithmetic operations are: +, -,*, /, (, ), { and }. { and } are used to define the constant.
WOFD-031100
Function: Performance Measurement Data Query Template
Description:
The Performance Measurement Data Query Templatefunction enables users to save thequery conditions of performance data as a template.
The query templates are stored by user. When users use a template to query performance data,they do not need to specify the query conditions.
The system displays the data that satisfiesthe conditions of the template.
WOFD-031200
Function: Threshold Alarm
Description:
TheThreshold Alarm function enables users to specify alarm thresholds for the measurementcounters. When the counter value exceeds the threshold, a performance alarm is triggered.
A counter can have more than one threshold for different measurement objects or differentmeasurement time.
2.4 Security Management
WOFD-040100
Function: Centralized Management of Users and User Groups
Description:
The Management of Users and User Groupsfunction is used to perform the following
operations on the users and user groups in the entire network (including the users and usergroups of the EMS and the NEs):
l Addition
l Deletion
l Modification
l Authorization allocation
This function also allows copying and pasting the authorization; thus saving the redundant
procedures of authorization.
-
8/10/2019 IManager M2000
24/38
FOR INTERNAL USE ONLY
Function Description of M2000 for WiMAX
Function Description
Issue 1.10 (2008-11-03) Huawei Technologies Proprietary Page 24 of 38
The system supports the role-based user group management and authority management. The
authority for operation is allocated to user groups based on the roles.
The operation authority includes the authority for the operation of:
l
EMSl NEs
One user can belong to one or more user groups.
The NE users are categorized into the following two types:
l Local user
l Domain user
The NE user in the centralized management refers to the domain user. At present, only the domain usersof the ASN-GW support the centralized management on the NMS.
WOFD-040200Function: Centralized User Authentication
Description:
TheUser Authenticationfunction conducts authentication for the operation and maintenanceusers in the entire network.
When you log in to the EMS through client or to the NE through LMT, the EMS performs theauthentication by checking your account and password. Only with the valid user account, youcan log in to and operate the system.
For all of the operations through client and LMT, the EMS performs the authentication for
each operation. The EMS also validates each operation based on:
l Authority that a user account has
l Significance and scale of the operation
In this way, the operations that need extra authority of the users are prohibited.
1Centralized authentication is supported when using the user count of the EMS to log on to the EMS.
2The NE users are categorized into the following two types:
l Local user
l Domain user
The domain user logs on to the NE through the LMT. Centralized authentication is supported on theEMS, At present, only ASN-GW supports such function.
WOFD-040300
Function: Security Policy
Description:
The Security Policyfunction enables users to set flexible security policies, including:
l Shortest length of a password
l Least special characters of a password
l Least numbers of passwords
-
8/10/2019 IManager M2000
25/38
FOR INTERNAL USE ONLY
Function Description of M2000 for WiMAX
Function Description
Issue 1.10 (2008-11-03) Huawei Technologies Proprietary Page 25 of 38
l Least letters of a password
l Valid period (days) of a password
l Minimum interval of the consecutive two passwords
l Number of history passwords that can not be reused recently
l Maximum attempts of login
l Laws and regulations displayed after the user logs in
l Auto locking time duration (minutes) when login attempts of a user exceed themaximum login attempts
WOFD-040400
Function: Terminal Auto Locking
Description:
The Terminal Auto Lockingfunction ensures that a terminal is automatically locked if there
is no operation for a period. The locked terminal can only be unlocked by the previously useraccount.
WOFD-040500
Function: User Online Monitoring
Description:
The User Monitoringfunction enables users to monitor all the online system users.Information like user name, actions, action time, result and terminal and so on are displayedon the monitoring interface.
This function also supports forced kick out of specified user.
WOFD-040600
Function: NE User Management
Description:
TheNE User Managementfunction enables you to set the EMS users created on the M2000GUI as NE users and assign the NE users with operation authority. That is, you can log in tothe NE through the LMT as the NE user.
The NE users can log in to the system as well as log in to the NEs through LMT. Operation
authority is consistent in these two situations.
The NE User Management is subject to the previous versions of the NEs, that is, theversions before the UMTS6.0. For the versions later than UMTS6.0 (including UMTS6.0),you can use the Centralized User Management (WOFD-040100) to manage the NE users.
WOFD-040700
Function: NE user Online Monitoring
Description:
The NE user Online Monitoringfunction allows users to monitor all online NE users. The
monitored information includes the user name, user type, client IP address, login time, server
-
8/10/2019 IManager M2000
26/38
FOR INTERNAL USE ONLY
Function Description of M2000 for WiMAX
Function Description
Issue 1.10 (2008-11-03) Huawei Technologies Proprietary Page 26 of 38
IP address, whether logging in through Proxy, operations, operation time, and results returned
for operations. All the information is monitored in real time and displayed on the client.
The NE User Online Monitoringfunction also enables users to force a specified user out.
2.5 Log Management
WOFD-050100
Function: EMS Log Record
Description:
All the information during the operation of the EMS is recorded in the log.
Table 2-1Types of logs
Type Description
Operation log Records all of the operations performed by users. The recordsdeal with the following aspects:
l User name
l Terminal
l Operation time
l Operation object
l Operation name
l Operation result
Running log Records the running status of the system.
Security log Records the events that have vital influence on the system
security. In the security log, the following types of events arerecorded:
l Account management event
l Account login event
l System event (Events that have vital influence on the systemsecurity and security log when you reboot the system orpower off the system)
l Resource access event (Attempts to access the objects forwhich you have no authority)
WOFD-050200
Function: EMS Log Query
Description:
The Log Query function enables users to query the log information according to specified
conditions.
-
8/10/2019 IManager M2000
27/38
FOR INTERNAL USE ONLY
Function Description of M2000 for WiMAX
Function Description
Issue 1.10 (2008-11-03) Huawei Technologies Proprietary Page 27 of 38
Various log types have different supported conditions.
Supported query conditions for different logs are as follows:
l Operation log: terminal, operation , operation object, that is, the NE, time, user, and the
operation result.l Running log: source, level, and time
l Security log: event level, user, terminal, security event, time, object, that is the NE, andoperation result..
WOFD-050300
Function: Log Printing
Description:
The Log Printing function enables users to print log information in the inquiring window.
WOFD-050400
Function: Log Saving
Description:
The Log Saving function enables users to save the log information in the inquiring window asfiles.
Supported file formats are: TXT, HTML, XSL, and CSV.
WOFD-050500
Function: Log Export
Description:
The Log Exportfunction periodically exports the log information from database to the file.
The file is in .txt format.
The Log Exportfunction exports the log data that exceeds the predefined time range into a
file and deletes the log-related records from the database. In this way, the database isprotected. The file that saves the log data is located in the default server path. The condition tobe is Saving Days. The data that exceeds the range of Saving Daysis exported and deleted.
The Log Export function is realized when theCentralized Task Management is enabled.
WOFD-050600
Function: NE Log Query
Description:
The NE Log Query function enables users to browse the NE local operation and maintenancelogs and the security logs that meet the requirements of the conditions on the NMS interface.
Supported query conditions for NE operation logs are as follows:
l User name
l User type
-
8/10/2019 IManager M2000
28/38
FOR INTERNAL USE ONLY
Function Description of M2000 for WiMAX
Function Description
Issue 1.10 (2008-11-03) Huawei Technologies Proprietary Page 28 of 38
l Terminal
l NE
l Operation result
l Operation time
Supported query conditions for NE security logs are as follows:
l Time
l User
l User type
l Security level
l Terminal
l Operation result
l NE
The log query conditions can be saved as a template.
WOFD-050700
Function: Log Statistics
Description:
The Log Statistics function supports displaying queried log statistics in tables. The logstatistics include operation logs, operators, and number of operations.
2.6 Topology Management
WOFD-060100
Function: Topology Object Management
Description:
The Topology Object Managementfunction enables users to add, delete and modify
topology objects on the topology GUI.
Supported topology objects are: NE, link and subnet.
l NEThe topology view supports using different icons to indicate different NEs.
If the corresponding equipment is managed by the system, the NE is physical NE intopology view. Or else, it is virtual NE.
The system itself is a special NE in topology view.
l Link
Topology view supports marking the physical or logical connection between NEs bylink.
There are two types of link: physical link and virtual link. The former represents the
actual link between two physical NEs. The latter represents manually set up to better
present the connections between NEs in the topology view.
-
8/10/2019 IManager M2000
29/38
FOR INTERNAL USE ONLY
Function Description of M2000 for WiMAX
Function Description
Issue 1.10 (2008-11-03) Huawei Technologies Proprietary Page 29 of 38
l Subnet
The topology view supports grouping the NEs by subnet to separate a big networkconfiguration to several smaller ones.
WOFD-060300Function: Topology Navigation
Description:
TheTopology Navigationfunction supports displaying NE and link by map and navigation
tree. It also provides operators with interfaces of configuration, alarm and performance relatedoperations.
On the topology view, the navigation tree on the left shows the topology objects (NE andsubnet) and their hierarchy. The map on the right shows all the topology objects and theirhierarchy on the current subnet and the alarm status of the topology objects.
The navigation tree and map are synchronous. The map on the right shows a certain topologyobject when it is selected on the tree.
WOFD-060400
Function: Topology Map Management
Description:
The Topology Map Management function enables users to change the background oftopology map.
The system supports bitmap.
WOFD-060500
Function: Topology Object Searching and Locating
Description:
TheTopology Object Searching and Locatingfunction enables users to search for andlocate specified topology object.
The search supports multiple dimensions, including object name and property. Property hererefers to IP, version number, supplier and location information.
Fuzzy search by name or property is supported.
2.7 System Management
WOFD-070100
Function: Local Maintenance Agent
Description:
The system provides a proxy for LMT to communicate with NEs. When NE and LMT are in
separate network section, LMT can still maintain NE through proxy provided by the system.
-
8/10/2019 IManager M2000
30/38
FOR INTERNAL USE ONLY
Function Description of M2000 for WiMAX
Function Description
Issue 1.10 (2008-11-03) Huawei Technologies Proprietary Page 30 of 38
WOFD-070200
Function: Centralized MML
Description:
The Centralized MMLfunction provides integrated command line GUI interface, enables
users to deliver MML command to NEs.
The interface supports command prediction, navigation tree and online help.
WOFD-070600
Function: System Monitoring
Description:
TheSystem Monitoringfunction supports online monitoring of system running status andhardware status.
The system status to be monitored includes:
l Status of service and process
l CPU usage
l Memory usage
l Database utility
l Disk utility
You can also set the thresholds for the system. If a counter exceeds the predefined threshold,
the system generates an alarm. When a counter is within the range of thresholds, the generated
alarm is cleared.
The hardware to be monitored includes:
l Disk
l CPU
l Memory
l Disk array
l Network port
l Battery
l Environment
When the hardware becomes faulty, the system generates alarms.
WOFD-070700
Function: Online Help
Description:
The Online Helpfunction supports hot spot help, full-text search, and offline browse. Its
content includes:
l System function explanation: descriptions and operating procedure steps of FaultManagement, Configuration Management, Performance Management, System
Management, Security Management and Topology Management.
-
8/10/2019 IManager M2000
31/38
-
8/10/2019 IManager M2000
32/38
FOR INTERNAL USE ONLY
Function Description of M2000 for WiMAX
Function Description
Issue 1.10 (2008-11-03) Huawei Technologies Proprietary Page 32 of 38
WOFD-080300
Function: Backup and Restore
Description:
The system supports backup and restore of the system data. In case of system failure, the
backup can be restored to recover the system status to the latest status.
The data that can be backed up include system application software, operating system,
database software and other data.
The backup mediums are tapes and disks.
The System supports auto-backup and manual backup, the backup time and interval isconfigurable.
The system also supports the full backup and the incremental backup.
WOFD-080400
Function: NE Data Backup and Restore
Description:
TheNE Data Backup and Restorefunction enables users to back up all NE data on thesystem. When NE loses data for failure, the data can be recovered by backup files on thesystem.
The backup files are saved on the hard disk of server and can be backed up to other mediums.
The above NE data refers to the configuration data of an NE.
-
8/10/2019 IManager M2000
33/38
FOR INTERNAL USE ONLY
Function Description of M2000 for WiMAX
Function Description
Issue 1.10 (2008-11-03) Huawei Technologies Proprietary Page 33 of 38
3 Optional Functions3.1 Customization Performance Report System
WOFD-090100
Function: Customization Performance Report System
Description:
The system provides web based performance report tools and supports periodically generatingreport and summarizing the data according to performance objects, metrics and timedimension. Users can customize the format and content of the report.
The format and content of reports are customizable.
Service benefits:
To the operator:
The data can be grouped into diagram by custom report to evaluate the network quality andmake decisions in network maintenance.
To the end user:
None.
Requirements on peripheral network entities:
None.
3.2 Northbound Interface To NMS
WOFD-100110
Function: CORBA Alarm Interface
Description:
The system provides a CORBA Alarm Interfacewhich complies with 3GPP R6specifications.
-
8/10/2019 IManager M2000
34/38
FOR INTERNAL USE ONLY
Function Description of M2000 for WiMAX
Function Description
Issue 1.10 (2008-11-03) Huawei Technologies Proprietary Page 34 of 38
Service benefits:
To the operator:
Through this interface, the network management system (NMS) can conveniently obtain the
alarm data of the network and acknowledge or unacknowledged, clear the alarms, whichcentralizes the management of the alarms in the whole network and reduces management cost
of the operator.
To the end user:
None.
Requirements on peripheral network entities:
The NMS must support the corresponding interface compliant with 3GPP R6 specifications.
WOFD-100210
Function: File Alarm Data Interface
Description:
The system supports periodically save the alarm data of database to the file. NMS or the thirdpartys system can obtain these files by FTP.
Service benefits:
To the operator:
The interface simplifies interconnect to NMS or the third party system and improves theinterface efficiency.
To the end user:
None.
Requirements on peripheral network entities:
The peer system must support the file interface.
WOFD-100210
Function: File Performance Data Interface
Description:
The system supports periodically save the performance data of database to the file. NMS orthe third partys system can obtain these files by FTP.
Service benefits:
To the operator:
The interface simplifies interconnect to NMS or the third party system and improves theinterface efficiency.
To the end user:
None.
Requirements on peripheral network entities:
-
8/10/2019 IManager M2000
35/38
FOR INTERNAL USE ONLY
Function Description of M2000 for WiMAX
Function Description
Issue 1.10 (2008-11-03) Huawei Technologies Proprietary Page 35 of 38
The peer system must support the file interface.
WOFD-100230
Function: File Configuration Data Interface
Description:
The system supports periodically save the configuration data of database to the file. NMS orthe third partys system can obtain these files by FTP.
Service benefits:
To the operator:
The interface simplifies interconnect to NMS or the third party system and improves the
interface efficiency.
To the end user:
None.
Requirements on peripheral network entities:
The peer system must support the file interface.
WOFD-100400
Function: Alarm Streaming Interface
Description:
The system provides character streaming alarm interface, sending the alarms to the NMS or
the third party system in character stream.
Service benefits:
To the operator:
This interface has higher efficiency and easier access.
To the end user:
None.
Requirements on peripheral network entities:
The peer system must support TCP/IP.
WOFD-100500
Function: SNMP Alarm Interface
Description:
The M2000 provides an SNMP alarm interface for forwarding alarms to the NMS or
third-party system in the form of text. The SNMP alarm interface complies with the SNMPprotocol specifications. The SNMP alarm interface supports alarm synchronization.
Service benefits:
To the operator:
-
8/10/2019 IManager M2000
36/38
FOR INTERNAL USE ONLY
Function Description of M2000 for WiMAX
Function Description
Issue 1.10 (2008-11-03) Huawei Technologies Proprietary Page 36 of 38
The SNMP alarm interface has the advantages of high efficiency, timely response, and easy
access.
To the end user:
None.Requirements on peripheral network entities:
The peer system must support TCP/IP.
3.3 NE Software Management
WOFD-110100
Function: NE Software Management
Description:
The ASN-GW supports the following functions:
l Software downloading from EMS to NE
When the software is downloaded to the standby area of NE, the current version is not covered. Thedownloading progress is initiatively reported by the NE.
l Software activation
The active and standby areas are automatically switched.
l Software version query
l Downloads of the patches and data from the EMS to the NEs
The BS supports the following functions:
l Bulk NEs upgrade
l Software downloading from EMS to NE
When the software is downloaded to the standby area, the current version is not covered. Thedownloading progress is initiatively reported by the NE.
l Software activation
The active and standby areas are automatically switched .
l Software version query
Service benefits:
To the operator:
This function lowers the maintenance cost of the operators. The maintenance staffs do nothave to transfer the file to NE one by one or copy the software on the LMT of NE. It savesupgrading work and time at the same time lowers the possibility of man-made error.
To the end user:
None.
Requirements on peripheral network entities:
None.
-
8/10/2019 IManager M2000
37/38
FOR INTERNAL USE ONLY
Function Description of M2000 for WiMAX
Function Description
Issue 1.10 (2008-11-03) Huawei Technologies Proprietary Page 37 of 38
3.4 Alarm Remote Notification
WOFD-120100
Function: Alarm Remote Notification
Description:
TheAlarm Remote Notification function notifies the maintenance engineer of alarms that
satisfy specified conditions through short message and E-mail. Supported conditions are:alarm severity level, alarm type, alarm name and NE.
Service benefits:
To the operator:
The system can deliver the key network faults in time to the related maintenance staff. Theengineers know the network running status on or off site so that the machine room needs no
people to be on duty.
To the end user:
None.
Requirements on peripheral network entities:
A short message Modem is needed in short message notification.
A mail server is needed in E-mail notification.
3.5 HA System
WOFD-130100
Function: HA System
Description:
The system supports HA. There two servers, which form a cluster, and work as the standbyserver of each other. When the main server fails, the system will auto switches to the spareserver.
Service benefits:
To the operator:
Reducing the downtime of server and reducing the service effect, if the main server is failure,
the system will changeover to the backup server automatically without intervention.
To the end user:
None.
Requirements on peripheral network entities:
None.
-
8/10/2019 IManager M2000
38/38
FOR INTERNAL USE ONLY
Function Description of M2000 for WiMAX
Function Description
3.6 Support Vector Map on Topology
WOFD-140100
Function: Support Vector Map on Topology
Description:
System provides Vector Map in Topology with MID/MIF format, supports zoom out and
zoom in partially, supports longitude and latitude attributes of network element, supportssome additional romance futures.
Service benefits:
To the operator:
Operator can do more operation and get more information in topology.
To the end user:
None.
Requirements on peripheral network entities:
None