im10312 precision tig 275 · 2018. 11. 22. · precision tig ®275 register your ... keep your head...

Operator’s Manual

PRECISION TIG ®275

Register your machine: www.lincolnelectric.com/register

Authorized Service and Distributor Locator: www.lincolnelectric.com/locator

IM10312 | Issue D ate Aug-15

© Lincoln Global, Inc. All Rights Reserved.

For use with machines having Code Numbers:

12490

Save for future reference

Date Purchased

Code: (ex: 10859)

Serial: (ex: U1060512345)

THANK YOU FOR SELECTING A QUALITY PRODUCT BY LINCOLN ELEC TRIC.

PLEASE EXAMINE CARTON AND EQUIPMENT FORDAMAGE IMMEDIATELY

When this equipment is shipped, title passes to the purchaserupon receipt by the carrier. Consequently, claims for materialdamaged in shipment must be made by the purchaser against thetransportation company at the time the shipment is received.

SAFETY DEPENDS ON YOU

Lincoln arc welding and cutting equipment is designed and builtwith safety in mind. However, your overall safety can be increasedby proper installation ... and thoughtful operation on your part. DO NOT INSTALL, OPERATE OR REPAIR THIS EQUIPMENT WITHOUT READING THIS MANUAL AND THE SAFETYPRECAUTIONS CONTAINED THROUGHOUT. And, most importantly,think before you act and be careful.

This statement appears where the information must be followedexactly to avoid serious personal injury or loss of life.

This statement appears where the information must be followedto avoid minor personal injury or damage to this equipment.

KEEP YOUR HEAD OUT OF THE FUMES.

DON’T get too close to the arc.Use corrective lenses if necessaryto stay a reasonable distanceaway from the arc.

READ and obey the Safety DataSheet (SDS) and the warning labelthat appears on all containers ofwelding materials.

USE ENOUGH VENTILATION orexhaust at the arc, or both, tokeep the fumes and gases from your breathing zone and the general area.

IN A LARGE ROOM OR OUTDOORS, natural ventilation may beadequate if you keep your head out of the fumes (See below).

USE NATURAL DRAFTS or fans to keep the fumes away from your face.

If you de velop unusual symptoms, see your supervisor. Perhaps the welding atmosphere and ventilation system should be checked.

WEAR CORRECT EYE, EAR & BODY PROTECTION

PROTECT your eyes and face with welding helmetproperly fitted and with proper grade of filter plate(See ANSI Z49.1).

PROTECT your body from welding spatter and arcflash with protective clothing including woolenclothing, flame-proof apron and gloves, leatherleggings, and high boots.

PROTECT others from splatter, flash, and glarewith protective screens or barriers.

IN SOME AREAS, protection from noise may be appropriate.

BE SURE protective equipment is in good condition.

Also, wear safety glasses in work areaAT ALL TIMES.

SPECIAL SITUATIONS

DO NOT WELD OR CUT containers or materials which previouslyhad been in contact with hazardous substances unless they areproperly cleaned. This is extremely dangerous.

DO NOT WELD OR CUT painted or plated parts unless specialprecautions with ventilation have been taken. They can releasehighly toxic fumes or gases.

Additional precautionary measures

PROTECT compressed gas cylinders from excessive heat,mechanical shocks, and arcs; fasten cylinders so they cannot fall.

BE SURE cylinders are never grounded or part of an electrical circuit.

REMOVE all potential fire hazards from welding area.

ALWAYS HAVE FIRE FIGHTING EQUIPMENT READY FORIMMEDIATE USE AND KNOW HOW TO USE IT.

WARNING

CAUTION

Safety 01 of 04 - 5/16/2018

SECTION A:WARNINGS

CALIFORNIA PROPOSITION 65 WARNINGS

WARNING: Breathing diesel engine exhaustexposes you to chemicals known to the Stateof California to cause cancer and birth defects,

or other reproductive harm.• Always start and operate the engine in a

well-ventilated area.• If in an exposed area, vent the exhaust to the outside.• Do not modify or tamper with the exhaust system. • Do not idle the engine except as necessary.For more information go to www.P65 warnings.ca.gov/diesel

WARNING: This product, when used for welding or

cutting, produces fumes or gases which contain

chemicals known to the State of California to cause

birth defects and, in some cases, cancer. (California

Health & Safety Code § 25249.5 et seq.)

WARNING: Cancer and Reproductive Harm

www.P65warnings.ca.gov

ARC WELDING CAN BE HAZARDOUS. PROTECTYOURSELF AND OTHERS FROM POSSIBLE SERIOUSINJURY OR DEATH. KEEP CHILDREN AWAY. PACEMAKER WEARERS SHOULD CONSULT WITHTHEIR DOCTOR BEFORE OPERATING.

Read and understand the following safety highlights. Foradditional safety information, it is strongly recommended that you purchase a copy of “Safety in Welding & Cutting - ANSI Standard Z49.1” from the American Welding Society, P.O. Box 351040, Miami, Florida 33135 or CSA Standard W117.2-1974. A Free copy of “Arc Welding Safety” booklet E205 is available from the Lincoln Electric Company, 22801 St. Clair Avenue, Cleveland, Ohio 44117-1199.

BE SURE THAT ALL INSTALLATION, OPERATION,MAINTENANCE AND REPAIR PROCEDURES AREPERFORMED ONLY BY QUALIFIED INDIVIDUALS.

FOR ENGINE POWEREDEQUIPMENT.

1.a. Turn the engine off before troubleshootingand maintenance work unless themaintenance work requires it to be running.

1.b. Operate engines in open, well-ventilated areas or vent the engineexhaust fumes outdoors.

1.c. Do not add the fuel near an open flame weldingarc or when the engine is running. Stop theengine and allow it to cool before refueling toprevent spilled fuel from vaporizing on contact

with hot engine parts and igniting. Do not spill fuel when fillingtank. If fuel is spilled, wipe it up and do not start engine untilfumes have been eliminated.

1.d. Keep all equipment safety guards, covers and devices in position and in good repair.Keep hands, hair, clothing and tools away from V-belts, gears, fans and all other moving parts when starting, operating orrepairing equipment.

1.e. In some cases it may be necessary to remove safety guards toperform required maintenance. Remove guards only whennecessary and replace them when the maintenance requiringtheir removal is complete. Always use the greatest care whenworking near moving parts.

1.f. Do not put your hands near the engine fan. Do not attempt tooverride the governor or idler by pushing on the throttle controlrods while the engine is running.

1.g. To prevent accidentally starting gasoline engines while turningthe engine or welding generator during maintenance work,disconnect the spark plug wires, distributor cap or magneto wireas appropriate.

1.h. To avoid scalding, do not remove the radiatorpressure cap when the engine is hot.

ELECTRIC ANDMAGNETIC FIELDS MAYBE DANGEROUS

2.a. Electric current flowing through any conductorcauses localized Electric and Magnetic Fields (EMF). Welding current creates EMF fields around welding cables and welding machines

2.b. EMF fields may interfere with some pacemakers, and welders having a pacemaker should consult their physicianbefore welding.

2.c. Exposure to EMF fields in welding may have other health effectswhich are now not known.

2.d. All welders should use the following procedures in order tominimize exposure to EMF fields from the welding circuit:

2.d.1. Route the electrode and work cables together - Securethem with tape when possible.

2.d.2. Never coil the electrode lead around your body.

2.d.3. Do not place your body between the electrode and workcables. If the electrode cable is on your right side, thework cable should also be on your right side.

2.d.4. Connect the work cable to the workpiece as close as pos-sible to the area being welded.

2.d.5. Do not work next to welding power source.

SAFETY

Safety 02 of 04 - 5/16/2018

ELECTRIC SHOCK CAN KILL.

3.a. The electrode and work (or ground) circuits areelectrically “hot” when the welder is on. Donot touch these “hot” parts with your bare skin or wet clothing.Wear dry, hole-free gloves to insulate hands.

3.b. Insulate yourself from work and ground using dry insulation.Make certain the insulation is large enough to cover your full areaof physical contact with work and ground.

In addition to the normal safety precautions, if

welding must be performed under electrically

hazardous conditions (in damp locations or while

wearing wet clothing; on metal structures such as

floors, gratings or scaffolds; when in cramped

positions such as sitting, kneeling or lying, if there

is a high risk of unavoidable or accidental contact

with the workpiece or ground) use the following

equipment:

• Semiautomatic DC Constant Voltage (Wire) Welder.

• DC Manual (Stick) Welder.

• AC Welder with Reduced Voltage Control.

3.c. In semiautomatic or automatic wire welding, the electrode,electrode reel, welding head, nozzle or semiautomatic weldinggun are also electrically “hot”.

3.d. Always be sure the work cable makes a good electricalconnection with the metal being welded. The connection shouldbe as close as possible to the area being welded.

3.e. Ground the work or metal to be welded to a good electrical (earth)ground.

3.f. Maintain the electrode holder, work clamp, welding cable andwelding machine in good, safe operating condition. Replacedamaged insulation.

3.g. Never dip the electrode in water for cooling.

3.h. Never simultaneously touch electrically “hot” parts of electrodeholders connected to two welders because voltage between thetwo can be the total of the open circuit voltage of bothwelders.

3.i. When working above floor level, use a safety belt to protectyourself from a fall should you get a shock.

3.j. Also see It ems 6.c. and 8.

ARC RAYS CAN BURN.

4.a. Use a shield with the proper filter and cover plates to protect youreyes from sparks and the rays of the arc when welding orobserving open arc welding. Headshield and filter lens shouldconform to ANSI Z87. I standards.

4.b. Use suitable clothing made from durable flame-resistant materialto protect your skin and that of your helpers from the arc rays.

4.c. Protect other nearby personnel with suitable, non-flammablescreening and/or warn them not to watch the arc nor exposethemselves to the arc rays or to hot spatter or metal.

FUMES AND GASESCAN BE DANGEROUS.

5.a. Welding may produce fumes and gaseshazardous to health. Avoid breathing thesefumes and gases. When welding, keep your head out of the fume.Use enough ventilation and/or exhaust at the arc to keep fumesand gases away from the breathing zone. When welding

hardfacing (see instructions on container or SDS)

or on lead or cadmium plated steel and other

metals or coatings which produce highly toxic

fumes, keep exposure as low as possible and

within applicable OSHA PEL and ACGIH TLV limits

using local exhaust or mechanical ventilation

unless exposure assessments indicate otherwise.

In confined spaces or in some circumstances,

outdoors, a respirator may also be required.

Additional precautions are also required when

welding

on galvanized steel.

5. b. The operation of welding fume control equipment is affected byvarious factors including proper use and positioning of theequipment, maintenance of the equipment and the specificwelding procedure and application involved. Worker exposurelevel should be checked upon installation and periodicallythereafter to be certain it is within applicable OSHA PEL andACGIH TLV limits.

5.c. Do not weld in locations near chlorinated hydrocarbon vaporscoming from degreasing, cleaning or spraying operations. Theheat and rays of the arc can react with solvent vapors to formphosgene, a highly toxic gas, and other irritating products.

5.d. Shielding gases used for arc welding can displace air and causeinjury or death. Always use enough ventilation, especially inconfined areas, to insure breathing air is safe.

5.e. Read and understand the manufacturer’s instructions for thisequipment and the consumables to be used, including theSafety Data Sheet (SDS) and follow your employer’s safetypractices. SDS forms are available from your weldingdistributor or from the manufacturer.

5.f. Also see item 1.b.

SAFETY

Safety 03 of 04 - 5/16/2018

WELDING AND CUTTINGSPARKS CAN CAUSEFIRE OR EXPLOSION.

6.a. Remove fire hazards from the welding area. Ifthis is not possible, cover them to prevent the welding sparksfrom starting a fire. Remember that welding sparks and hotmaterials from welding can easily go through small cracks andopenings to adjacent areas. Avoid welding near hydraulic lines.Have a fire extinguisher readily available.

6.b. Where compressed gases are to be used at the job site, specialprecautions should be used to prevent hazardous situations.Refer to “Safety in Welding and Cutting” (ANSI Standard Z49.1)and the operating information for the equipment being used.

6.c. When not welding, make certain no part of the electrode circuit istouching the work or ground. Accidental contact can causeoverheating and create a fire hazard.

6.d. Do not heat, cut or weld tanks, drums or containers until theproper steps have been taken to insure that such procedures will not cause flammable or toxic vapors from substances inside.They can cause an explosion even though they have been“cleaned”. For information, purchase “Recommended SafePractices for the Preparation for Welding and Cutting ofContainers and Piping That Have Held Hazardous Substances”,AWS F4.1 from the American Welding Society (see address above).

6.e. Vent hollow castings or containers before heating, cutting orwelding. They may explode.

6.f. Sparks and spatter are thrown from the welding arc. Wear oil freeprotective garments such as leather gloves, heavy shirt, cufflesstrousers, high shoes and a cap over your hair. Wear ear plugswhen welding out of position or in confined places. Always wearsafety glasses with side shields when in a welding area.

6.g. Connect the work cable to the work as close to the welding areaas practical. Work cables connected to the building framework orother locations away from the welding area increase thepossibility of the welding current passing through lifting chains,crane cables or other alternate circuits. This can create firehazards or overheat lifting chains or cables until they fail.

6.h. Also see item 1.c.

6.I. Read and follow NFPA 51B “Standard for Fire Prevention DuringWelding, Cutting and Other Hot Work”, available from NFPA, 1Batterymarch Park, PO box 9101, Quincy, MA 022690-9101.

6.j. Do not use a welding power source for pipe thawing.

CYLINDER MAY EXPLODE IFDAMAGED.

7.a. Use only compressed gas cylinders containingthe correct shielding gas for the process usedand properly operating regulators designed forthe gas and pressure used. All hoses, fittings,etc. should be suitable for the application andmaintained in good condition.

7.b. Always keep cylinders in an upright position securely chained toan undercarriage or fixed support.

7.c. Cylinders should be located:

• Away from areas where they may be struck or subjectedto physical damage.

• A safe distance from arc welding or cutting operationsand any other source of heat, sparks, or flame.

7.d. Never allow the electrode, electrode holder or any otherelectrically “hot” parts to touch a cylinder.

7.e. Keep your head and face away from the cylinder valve outletwhen opening the cylinder valve.

7.f. Valve protection caps should always be in place and hand tightexcept when the cylinder is in use or connected for use.

7.g. Read and follow the instructions on compressed gas cylinders,associated equipment, and CGA publication P-l, “Precautions forSafe Handling of Compressed Gases in Cylinders,” available fromthe Compressed Gas Association, 14501 George Carter WayChantilly, VA 20151.

FOR ELECTRICALLYPOWERED EQUIPMENT.

8.a. Turn off input power using the disconnectswitch at the fuse box before working on the equipment.

8.b. Install equipment in accordance with the U.S. National ElectricalCode, all local codes and the manufacturer’s recommendations.

8.c. Ground the equipment in accordance with the U.S. NationalElectrical Code and the manufacturer’s recommendations.

Refer to

http://www.lincolnelectric.com/safety

for additional safety information.

SAFETY

Safety 04 of 04 - 5/16/2018

6

SAFETY

TABLE OF CONTENTS Page Product Description ................................................................................................................................7 Recommended Processes and Equipment .......................................................................................7Installation .................................................................................................................................Section A Technical Specifications...............................................................................................................A-1, A-2 Safety Precautions ..............................................................................................................................A-3 Select Suitable Location...............................................................................................................A-3 Grinding.......................................................................................................................................A-3 Stacking ......................................................................................................................................A-3 Undercarriage Lifting and Moving ................................................................................................A-3 Tilting ..........................................................................................................................................A-3 Environmental Rating...................................................................................................................A-3 Machine Grounding and High Frequency Interference Protection..................................................A-3, A-4 Input and Grounding Connections.......................................................................................................A-4Output Cable, Connections and Limitations ..........................................................................................A-5

Work Cable Connection ........................................................................................................A-5 Stick Electrode Cable Connection .........................................................................................A-5 TIG Torch Connection............................................................................................................A-6 Auxiliary Power Connections ................................................................................................A-7 Remote Control (If Used).......................................................................................................A-7 Robotic Interface Connection ........................................................................................A-7, A-8_______________________________________________________________________________________OPERATION .......................................................................................................................................................................................Section B-1 Safety Precautions ..............................................................................................................................B-1 Pipe Thawing...............................................................................................................................B-1 Duty Cycle: ..................................................................................................................................B-1 Controls and Settings ..................................................................................................B-2 THRU B-6 Internal Set Up Controls ...............................................................................................................B-7 Stick Welding Features ................................................................................................................B-7 TIG Welding Features ...................................................................................................................B-7 2 Step Trigger Modes ...........................................................................................................B-8 4 Step Trigger Modes ..........................................................................................................B-9 TIG Welding Cycle Chart, Setup Guidelines for TIG Welding with an Amptrol ..............................B-10 Setup for TIG Amptrol Welding ...................................................................................................B-11 Making a TIG Weld with an Amptrol ...........................................................................................B-12_______________________________________________________________________________________Accessories ..................................................................................................................................Section C Optional Equipment .............................................................................................................................C-1_______________________________________________________________________________________Maintenance........................................................................................................................................................................................Section D Safety Precautions ..............................................................................................................................D-1 Routine and Periodic Maintenance ......................................................................................................D-1 Overload Protection.............................................................................................................................D-1 Service Procedures, Component Access,Spark Gap Adjustment ..........................................................D-2 Under-Cooler Service ..........................................................................................................................D-2 Meter Calibration Adjustment ..............................................................................................................D-3_______________________________________________________________________________________Troubleshooting.................................................................................................................................................................................Section E Safety Precautions...............................................................................................................................E-1 How To Use TroubleShooting Guide......................................................................................................E-1 Troubleshooting ........................................................................................................................E-2 to E-7_______________________________________________________________________________________Diagrams Section F Wiring Diagrams..........................................................................................................................................................................................F-1 Dimension Prints.........................................................................................................................................................................................F-2_______________________________________________________________________________________Parts List ...................................................................................................................................................................................................P-543

7

PRODUCT DESCRIPTIONPRECISION TIG® 275

PRODUCT DESCRIPTION

The Precision TIG® 275 is part of a family of industrial arc weldingpower sources providing constant current, single range squarewave AC/DC TIG (GTAW) with patented Micro-StartTM II Technology,Presettable Min. and Max. Output controls, and built-in high fre-quency stabilization for continuous AC TIG and DC TIG starting. Italso has AC/DC Stick (SMAW) capability, with adjustable Arc Forceavailability. A TIG Pulse Panel, Power Factor Capacitors and a WaterSolenoid are available as field installed optional kits. Also, a newUndercarriage (with double gas bottle rack) is available for fieldinstallation, as well as a new Under-Cooler Cart, which is alsoincluded in an available efficiently integrated entire TIG WeldingPackage with convenient built-in storage provisions for weldingequipment and components.

The Precision TIG® 275 includes advanced features such as: DigitalMeter, Presettable control, Auto BalanceTM, Fan As Needed (F.A.N.)fixed Preflow, variable Postflow shielding gas and Timers. In addi-tion, 2-Step/4-Step and Pulse TIG operation with adjustableDownslope Time control are included with an available fieldinstalled kit. It also features a Stick stud panel and a universal TIGtorch connection box for simultaneous, but separated, electrodeoutputs.

The Precision TIG® 275 has enhanced Features which includes thefollowing:

• MicroStart™ II • Auto-Balance optimized • Menu button added• Spot On selection added

RECOMMENDED PROCESSES AND EQUIPMENT

RECOMMENDED PROCESSESThe Precision TIG® 275 is recommended for the TIG (GTAW) andStick (SMAW) welding processes within its output capacity range of2 amps DC, or 5 amps AC, to 340 amps AC/DC. It is compatible withmost Magnum TIG accessories (refer Equipment Limitations), aswell as many industry standard items, such as TIG torches, hoses,and water coolers.

PROCESS LIMITATIONSPrecision TIG® machines are not recommended for arc gouging dueto it's limited output capacity, and are also not recommended forpipe thawing.

EQUIPMENT LIMITATIONSThe Precision TIG® machines are protected from overloads beyondthe electrical ratings and duty cycles, per the Specifications SectionA-1, A-2, with Thermostat protection of the primary and secondarytransformer coils.

The Precision TIG® machines do not have Hi-Frequency available atthe Stick electrode stud, therefore stud connection adapters (suchas LECO. S19257-series) cannot be used for torch connection.

RECOMMENDED EQUIPMENT/INTERFACE

TIG (air cooled)Machine: PT275Input Cable/Clamp: User providedGas Reg./Hose: LE/Harris 3100211Magnum Torch: PTA9 or PTA17Magnum Parts: KP507 or KP508 Work Clamp/Lead: K2150-1 Work Lead AssemblyFoot Amptrol: K870

A-1

INSTALLATIONPRECISION TIG® 275

TECHNICAL SPECIFICATIONS-Precision TIG® 275 (K2620-2 Export-50/60Hz)

Voltage+ 10%

220-230/380-400/415

Max. Amps With Out Power Factor Capacitor

95/55/50109/63/58

80/46/4285/49/45

70/41/3765/38/3510/6/5400W

Max. Amps With Power Factor Capacitor

80/46/4386/50/46

64/37/3467/39/36

52/30/2846/27/2523/13/12500W

Duty Cycle-Applications

40%AC/DC Stick / Balance TIG

Unbalance (70% Penetration#) AC TIG60%

AC/DC Stick / Balance TIGUnbalance (70% Penetration#) AC TIG


Unbalance (70% Penetration#) AC TIGIdle AmpsIdle Power

RATED INPUT - SINGLE PHASE ONLY

#Exceeds NEMA Unbalanced Load Specification comparable for Auto-Balance.

* 50/60HZ IEC Max. range exceeds 310A.

RATED POWER FACTOR (STICK) .65 min. .77 min.

RATED OUTPUT - IEC 60974-1 Duty Cycle-Applications


Unbalance (70% Penetration#) AC TIG60%

AC/DC Stick / Balance TIGUnbalance (70% Penetration#) AC TIG


Unbalance (70% Penetration#) AC TIG

Volts at Rated Amperes

31.0 20.2

29.0 18.0

28.016.0

Amps

275255

225200

200150

ADDITIONAL OUTPUT CAPACITYOutput Current

Range

2 Amps DCto 340 AmpsAC-DC*

Type of Output

CC (Constant Current)AC/DC (GTAW)Stick (SMAW)

Maximum Open Circuit Voltage

(STICK AND TIG)AC/DC OCV: 75/68

Auxiliary Power

5 Amp Circuit Breakerand grounded 220VAC Euro(Schuko) receptacle

A-2


Height31.0 in.787 mm

Width22.0 in.559 mm

Depth26.0 in.660 mm

WeightApprox. 397 lbs.

180 kgs.

PHYSICAL DIMENSIONS

1 ALSO CALLED ‘INVERSE TIME" OR "THERMAL/MAGNETIC " CIRCUIT BREAKERS; CIRCUIT BREAKERS WHICH HAVE A DELAY INTRIPPING ACTION THAT DECREASES AS THE MAGNITUDE OF CURRENT INCREASES.

TEMPERATURE RANGES

OPERATING TEMPERATURE RANGE-20°C to +40°C (-04° to +104°F)

TRANSFORMER INSULATION CLASS 180°C (H)

STORAGE TEMPERATURE RANGE-40°C to +85°C (-40° to +185°F)

For all Stick, DC TIG, and Balanced AC TIG Welding at275A/40% Duty Cycle with out Standard Power FactorCorrection Capacitors Based on the 1999 U.S. National

Electrical Code

RECOMMENDED INPUT WIRE AND FUSE SIZES

InputVoltage /phase/

Frequency

220-230/1/50/60

380-400/1/50/60

415/1/50/60

InputVoltage /phase/

Frequency

220-230/1/50/60

380-400/1/50/60

415/1/50/60

InputAmpereRating

Rating onNameplate

95

55

50

Type 75°CCopper GroundWire in ConduitAWG (IEC) Sizes

6 (13.3 mm2)

8 (8.4mm2)

8 (8.4mm2)

Fuse (SuperLag) orBreakerSize1

125

80

80

Type 75°CCopper Wire inConduit AWG

(IEC) Sizes 40°C(104°F) Ambient

4 (21.2 mm2)

8 (8.4mm2)

8 (8.4mm2)

IP21SN80

IEC 60974-1

For Unbalanced AC TIG Welding Above 275 Amps:255A/40% Duty Cycle, Auto-Balance Penetration with out

Standard Power Factor Correction CapacitorsBased on the 1999 U.S. National Electrical Code

InputAmpereRating

109

63

58

Type 75°CCopper GroundWire in ConduitAWG (IEC) Sizes

6 (13.3 mm2)

8 (8.4 mm2)

8 (8.4 mm2)

Fuse (SuperLag) orBreakerSize1

150

90

90

Type 75°CCopper Wire inConduit AWG

(IEC) Sizes 40°C(104°F) Ambient

4 (21.2 mm2)

6 (13.3 mm2)

6 (13.3 mm2)

A-3


SAFETY PRECAUTIONS ENVIRONMENTAL RATING

Precision TIG® 275 power sources carry an IP21S Environmentalrating. They are rated for use in damp, dirty rain-sheltered envi-ronments.

MACHINE GROUNDING AND HIGH FREQUENCYINTERFERENCE PROTECTION

The frame of the welder must be grounded. A ground screw marked withthe symbol is located on the input connection panel (Figure A.1) forthis purpose. See your local and national electrical codes for propergrounding methods.

The spark gap oscillator in the high frequency generator, beingsimilar to a radio transmitter, can be blamed for many radio, TVand electronic equipment interference problems. These prob-lems may be the result of radiated interference. Proper ground-ing methods can reduce or eliminate radiated interference.

The Precision TIG® 275 has been field tested under recommend-ed installation conditions and has been found to comply withF.C.C. allowable radiation limits. This welder has also been foundto comply with NEMA standards for high frequency stabilizedpower sources.

Radiated interference can develop in the following four ways:

• Direct interference radiated from the welder.• Direct interference radiated from the welding leads.• Direct interference radiated from feedback into the powerlines.

• Interference from re-radiation of "pickup" by ungroundedmetallic objects.

Keeping these contributing factors in mind, installing the equip-ment per the following instructions should minimize problems:

1. Keep the welder power supply lines as short as possible.Input leads within 50 feet (15.2 m) of the welder should beenclosed in rigid metallic conduit or equivalent shielding.There must be good electrical contact between this conduitand the welder. Both ends of the conduit must be connectedto a driven ground and the entire length must be continuous.

2. Keep the work and electrode leads as short as possible andas close together as possible. Lengths should not exceed 25feet (7.6 m). Tape the leads together when practical.

3. Be sure the torch and work cable rubber coverings are freeof cuts and cracks that allow high frequency leakage. Cableswith high natural rubber content, such as Lincoln Stable-Arc®, better resist high frequency leakage than neoprene andother synthetic rubber insulated cables.

4. Keep the torch in good repair and all connections tight toreduce high frequency leakage.

Read entire installation section before startinginstallation.

ELECTRIC SHOCK can kill.•Only qualified personnel should perform this installation.

•Turn the input power OFF at the disconnect switch or fuse box before working on this equipment.

• Do not touch electrically hot parts.

• Always connect the Precision TIG® 275 grounding screw (behind the recon-nect panel cover located near the back of the left case side) to a good elec-trical earth ground.

• Always connect the Precision TIG® 275 to a power supply grounded inaccordance with the National Electrical Code and all local codes.

------------------------------------------------------------------------------------------

SELECT SUITABLE LOCATIONThis equipment is for industrial use only and it is not intended for use in residential locations where the electrical is provided by the public low-voltage supply system. There can be potential difficulties in residential locations due to conducted as well as radiated radio-frequency disturbances. The EMC or RF classifi-cation of this equipment is Class A.

Place the welder where clean cooling air can freely circulate in through the top rear vents and out through the bottom rear vents. Dirt, dust or any foreign material that can be drawn into the welder should be kept at a minimum. Failure to observe these precautions can result in excessive operating tempera-tures and nuisance trips.

GRINDINGDo not direct grinding particles towards the welder. An abun-dance of conductive material can cause maintenance problems.

STACKINGThe Precision TIG® 275's cannot be stacked .

UNDERCARRIAGE LIFTING AND MOVING

When the Precision TIG® 275 is purchased as a welding pack-age, or used with any of the available Undercarriage optional accessories, proper installation makes the Precision TIG® 275 lift bale nonfunctional. Do not attempt to lift the power source with an undercarriage attached. The undercarriage is designed for hand moving only; mechanized movement can lead to per-sonal injury and/or damage to the Precision TIG® 275.

TILTINGEach machine must be placed on a secure, level surface, either directly or on a recommended undercarriage. The machine may topple over if this precaution is not followed.

WARNING

A-4


INPUT and GROUNDING CONNECTIONS

ELECTRIC SHOCK can kill.• Turn the input power OFF at the discon-nect switch or fuse box before workingon this equipment.

_______________________________________Be sure the voltage, phase, and frequency of the input power isas specified on the rating plate, located on the rear of themachine.

Fuse the input circuit with the recommended super lag fuses ordelay type1 circuit breakers. Choose an input and groundingwire size according to local or national codes or use Section A-2. Using fuses or circuit breakers smaller than recommendedmay result in "nuisance" tripping from welder inrush currentseven if not welding at high currents.

Unbalanced AC TIG welding draws higher input currents thanthose for Stick, DC TIG, or Balanced AC TIG welding. The welderis designed for these higher input currents. However, whereunbalanced AC TIG welding above 185 amps is planned, thehigher input currents require larger input wire sizes and fuses perSection A-2:

Remove the reconnect panel cover located near the back of theleft case side to reveal the reconnect panel. Welder supply lineentry provision is in the case rear panel. Entry is through a 1.75inch (44 mm) diameter hole in the case back. Appropriate sup-ply line strain relief clamp is provided by installer. (See FigureA.1)

All connections should be made in accordance with all localcodes and national electrical codes. Installation by a quali-fied electrician is recommended.

5. The work terminal must be connected to a ground within tenfeet of the welder, using one of the following methods:

• A metal underground water pipe in direct contact with theearth for ten feet or more.

• A 3/4" (19 mm) galvanized pipe or a 5/8" (16 mm) solidgalvanized iron, steel or copper rod driven at least eightfeet into the ground.

The ground should be securely made and the grounding cableshould be as short as possible using cable of the same size asthe work cable, or larger. Grounding to the building frame elec-trical conduit or a long pipe system can result in re-radiation,effectively making these members radiating antennas. (This isnot recommended).

6. Keep all access panels and covers securely in place.

7. All electrical conductors within 50 feet (15.2 m) of thewelder should be enclosed in grounded rigid metallic conduitor equivalent shielding. Flexible helically-wrapped metallicconduit is generally not suitable.

8. When the welder is enclosed in a metal building, severalgood earth driven electrical grounds (as in 5 above) aroundthe periphery of the building are recommended.

Failure to observe these recommended installation procedurescan cause radio or TV interference problems and result in unsat-isfactory welding performance resulting from lost high frequencypower.

FIGURE A.1

CONNECT INPUTPOWER LEADS

CONNECT INPUTVOLTAGE LEVEL

CONNECT INPUTGROUND LEAD

WARNING

A-5


Recommended Cable Sizes for Combined Lengths of CopperWork and Electrode Cables using 75o C Wire:

Machine Rating 0 to 100 Ft. 101 to 200 Ft 201 to 250 Ft

275A/40% #1 (42.4 mm2) 1/0 (53.5 mm2) 2/0 (67.4 mm2)

WORK CABLE CONNECTION

A 15’ (2/0) weld cable with clamp is available (K2150-1), Otherwise, itis user provided.

With power source off, connect a separate work cable to the1/2-13 threaded "WORK" stud of the welder, and secure a tightconnection with the flange nut provided. The work cable shouldbe routed through the cable strain relief hole provided in thebase directly below the welding output terminal.

Note: If the Precision TIG® is equipped with an Under-Cooler orUnder-Storage unit, the coiled work cable and clamp, or excesswork cable length, may be conveniently stored in the drawerwhile remaining connected.

STICK ELECTRODE CABLE CONNECTION

If manual stick welding is desired, with power source off, con-nect a stick electrode cable to the 1/2-13 threaded "STICKElectrode" stud of the welder, and secure a tight connectionwith the flange nut provided. The electrode cable should berouted through the cable strain relief hole provided in the basedirectly below the welding output terminal.

DISCONNECT STICK ELECTRODE WELDING CABLE WHEN TIG

WELDING.

EVEN THOUGH HI-FREQ IS NOT APPLIED TO THE PrecisionTIG® STICK TERMINAL, IT WILL BE ELECTRICALLY "HOT" TOWORK WHEN TIG WELDING.--------------------------------------------------------------------

1. Connect the terminal marked (below the reconnect panel)to an earth ground.

2. Connect the input leads to terminals marked L1 (U) and L2 (V)on the reconnect panel. Use a single phase line or one phaseof a two or three phase line.

3. On multiple input voltage welders, be sure the reconnectpanel is connected for the voltage being supplied to thewelder.

Failure to follow these instructions can cause immediatefailure of components within the welder.--------------------------------------------------------------------Welders are shipped connected for the highest input voltage aslisted on the rating plate. To change this connection, designa-tions on the reconnect panel LOW, MID, and HIGH correspond tothe name plated input voltages of a triple voltage welder. Dualvoltage welders use only LOW and HIGH.

EXAMPLE: This model has a voltage range for LOW and MIDconnections: LOW is 220-230V, MID is 380-400V and High is415V.

Reconnect the jumper strap to the terminal stud correspondingto the input voltage level used. Make sure all connections aretight.

OUTPUT CABLES, CONNECTIONS AND LIMITATIONS

• To avoid being startled by a high frequency shock, keepthe TIG torch and cables in good condition

• Turn the power switch of the power source OFF beforeinstalling adapters on cable or when connecting or dis-connecting adapter plugs to power source.

--------------------------------------------------------------------

Refer to Figure A.2 for the location of the WORK and STICK ter-minals, as well as the TIG Torch connection panel.

CAUTION

WARNING

WARNING

A-6


TIG TORCH CONNECTION

The Precision TIG® torch connection box, located on the rightside of the machine, provides all the input and output connec-tions for the installation of both air-cooled and water-cooled TIGtorches with fittings conforming to Compressed Gas Association(CGA) standards:Note: The Precision TIG® provides an insulated Torch Reel andHolster for handy and safe storage of connected torch when notwelding, and excess torch cable length while welding.Combination connectors (Power/Water and Power/Gas) are

electrically "hot" while welding in STICK or TIG modes.

If using an Air-Cooled Torch be sure coolant is shut offand/or Cooler is unplugged from the Precision TIG® WaterCooler Receptacle on the torch side of the upper case back.

Observe the safety precautions necessary for handling andusing compressed gas containers. Contact your supplier forspecifics.

CYLINDER could explode if damaged.• Keep cylinder upright and chained to asupport.

• Keep cylinder away from areas where itcould be damaged.

• Never allow the torch to touch the cylinder.• Keep cylinder away from live electrical circuits.• Maximum inlet pressure 150 psi.--------------------------------------------------------------------The Precision TIG® machines do not have Hi-Freq. available atthe Stick electrode stud, therefore stud connection adapters(such as LECO. S19257-series) cannot be used for torch con-nection.

Single-piece cable air-cooled torches with a 3/8-24 RH connectorfitting (such as the Magnum PTA-9/-17, or LA-9/-17) require theprovided S20403-4 Torch Connector, while those with a 7/8-14 RHconnector fitting (such as the Magnum PTA-26, or LA-26) requirethe available K2166-1 Torch Connector. (See Figure A.3)

Two-piece cable air-cooled torches (such as PTA-, or LA- torches)can be used with the available 1/2” Stud Connector (S20403-3)with with a 7/8-14 LH male fitting.

Magnum PTW-18/-20 (or LW-) water-cooled Torches require noadapter for Precision TIG® connection.

WORKSTICK WORKSTICK

STICKELE CTRODE

STUD

WORK

STUD

TIG TORCHCONNECTION

PANEL

FIGURE A(Shown without hinged stud cover)

REM OTE

CONTROLRECEPTACLE

CABLESTRAIN

REL IEF HOLE S

FIGURE A.2

WARNING

A-7


Torch AdapterAir Cooled Torch

OUTPUT (front) Panel

ELECTODE AND COOLANT IN 7/8-14 LH

COOLANT OUT 5/8-18 LH

ELECTODE AND/OR GAS OUTPUT 5/8-18 RH

INPUT (back) Panel

Two - Cable(PTA-9,-7,-26)

One - Cable (PTA-26)

One - Cable (PTA-9,-17)

K2166-2 (Opt.)

K2166-1 (Opt.)

S20403-4 (Incl.)

7/8-14 M-LH

5/8-18 M-RH

5/8-18 M-RH

7/8-14 F-RH

3/8-24 F-RH

7/8-14 F-RH

5/8-18 M-RH

3/8-24 M-RH

?-13 STUD

GAS INPUT 5/8-18 RH

COOLANT

IN

COOLANT

OUT

WAR

NING

UNPL

UG W

ATER

COO

LER

WHE

N US

ING

AIR

CO

OLE

D TO

RCHE

S

For Gas Supply Hoses with 5/8 - 18LH male (Provided withUnder-Cooler Cart)

For Gas Supply hosewith 5/8 - 18RH Male

AUXILIARY POWER CONNECTIONS

The Precision TIG® machines provide a standard NEMA 5-15Rduplex receptacle, located on the upper case back on the torchside of the machine:

• The bottom outlet of this duplex receptacle provides switched115VAC power for the Under-Cooler, or Water Solenoid acces-sory. This Cooler receptacle turns on when the arc starts andremains on for about 8 minutes after the arc goes out (withthe Fan-As-Needed machine cooling fan, see MaintenanceSection), so the Cooler’s fan and water pump will not run con-tinuously in idle, but will run while welding.

• The top outlet of this duplex receptacle provides at least 8amps at 115VAC, whenever the Precision TIG® Power switch isON. This auxiliary circuit is intended for running 115VACaccessories or small power tools.Note: Some types of equipment, especially pumps and largemotors, have starting currents which are significantly higherthan their running current. These higher starting currents maycause the circuit breaker to open. (See next paragraph)

• Both the receptacle circuits are protected from shorts andoverloads by a 15 amp circuit breaker, located above thereceptacle. If the breaker trips, its button pops out exposing ared ring. When the circuit breaker cools, the button can bereset by pressing it back in.

Note: When the breaker trips, not only will the auxiliary andcooler power be interrupted, but so will the power to theshielding gas solenoid and machine cooling fan. The PrecisionTIG® Export models also provide a grounded 220vac Euro typeSchuko receptacle and a 5 amp circuit breaker, located on theupper case back on the reconnect side of the machine, intend-ed for use with a 220vac water cooler.

REMOTE CONTROL (If Used)

The Foot Amptrol or other Remote accessory, is installed byrouting the plug of its control cable up through the left cablestrain relief hole provided in the base (see Figure A.2), then con-necting the 6-pin plug to the mating Remote receptacle behindthe stud panel cover. (See Operation Section B-2 for mating plugwiring.)

Note: If the Precision TIG® is equipped with an Under-Cooler orUnder-Storage unit, the Foot Pedal (or other remote controlaccessory) and coiled control cable, or excess cable length, maybe conveniently stored in the drawer while remaining connect-ed.

FIGURE A.3

A-8


ROBOTIC INTERFACE CONNECTION

Robotic interface can be made at the Remote Receptacle (SeeOperation Section B-2). The machine is shipped with the remotereceptacle circuit internally connected to receptacle J5 of theControl board for standard Amptrol operation. In order to enablethe remote receptacle for robotic interface its connection plugmust be moved from J5 to J5A on the Control board. (Refer tothe machine Wiring Diagram.)

The robotic interface functions with the Precision TIG® set toeither TIG or STICK mode, but must be in REMOTE switch posi-tion for the Preset Control interface to function. When in theREMOTE position with robotic interface neither the MAXIMUMOUTPUT nor the MINIMUM OUTPUT panel controls limit the inter-face control setting over the rated output range of the machine.

The diagram in Figure A.4 below shows the remote receptacleplug connections and signals for robotic interface:

In addition; a Peak Pulse output signal is provided at J21 recep-tacle on the Advanced Control PCB. This output provides a 0.2Arated switch circuit between pin 1 (+) and pin 2 (com) for anexternal 40VDC supplied relay (with coil diode). This switch clos-es when the Peak Pulse is on, and opens when off.

FIGURE A.4

B-1

OPERATIONPRECISION TIG® 275

PIPE THAWING

The Precision TIG® 275 is not recommended for pipe thawing.

Duty Cycle

The duty cycle is based upon a 10-minute time period; i.e., for40% duty cycle, it is 4 minutes welding and 6 minutes idling. Ifthe rated duty cycle is significantly exceeded, the thermostaticprotection will shut off the output until the machine cools to anormal operating temperature.

(Refer to Specification Section A-1)

ELECTRIC SHOCK can kill.• Only qualified personnel should perform this installation.• Turn the input power OFF at the disconnect switch or fuse box. • Do not touch electrically live parts orelectrode with skin or wet clothing.

• Insulate yourself from work and ground.• Always wear dry insulating gloves.• Read and follow “Electric Shock Warnings” inthe Safety section if welding must be performedunder electrically hazardous conditions such aswelding in wet areas or on or in the workpiece.

FUMES AND GASEScan be dangerous.• Keep your head out of fumes.• Use ventilation or exhaust to remove fumes from breathing zone.

WELDING SPARKScan cause fire orexplosion• Keep flammable material away.• Do not weld on containers that have held combustibles.

ARC RAYScan burn.

• Wear eye, ear and body protection.

SAFETY PRECAUTIONS

Read and understand this entire section before operating themachine.

Observe additional Safety Guidelines detailed in the begin-ning of this manual.

WARNING

B-2


1. POWER SWITCH - Input line switch turns input power ON orOFF, as indicated by the on or off status of the front panel dis-plays.

2. POLARITY SWITCH – The 3-position rotary power switch hasdetente positions for DC-, AC and DC+ selections for theElectrode output welding polarity.

3. MODE SWITCH – The mode switch allows vertically posi-tioned selection of the two machine welding modes. Theselected mode is indicated by a lit colored panel light whichpermits viewing the machine setting from a distance:3.a STICK mode (Top position) –Red panel light

ELECTRIC SHOCK can kill.• When the Power Source is ON in STICKmode the Electrode circuits of both theStick and TIG torch cables are electricallyHOT to Work.

--------------------------------------------------------------------

• The CC Stick mode may be used for general purpose stickwelding (SMAW ) within the capacity of the machine. Thecapacity is too limited for arc air carbon (AAC) gouging.

• In this mode; the output terminals are activated electricallyHOT, gas flow is not activated and HOT START and ARCFORCE levels are fixed, or Advanced Panel selectable (SeeInternal Set Up controls), with no front panel adjustment.

3.b TIG mode (Bottom position) – No panel light.

• When the Polarity Switch is set to AC, the TIG mode providescontinuous high frequency to stabilize the arc for AC TIGwelding.

Hi-Freq. turns on after preflow time with the arc start switchclosure, and turns off when the arc goes out* after the arcstart switch opens.

* Arc voltage and current are sensed to determine if the arc isestablished or out.

CONTROLS AND SETTINGS

The Front Control Panel contains the knobs and switches necessary for adjusting the operation of the Precision TIG® 275, with functionindicator lights and an electronic display for volts and amps. The components are described below:

FIGURE B.1 - CONTROL PANEL

1

2

3

4

5

9

6

13

11

10

7 7a

14 15 16 17

(Shown without hinged stud cover.)

12

WORKSTICK

8 91. POWER SWITCH 2. POLARITY SWITCH3. MODE SWITCH4. AC BALANCE CONTROL5. LOCAL/REMOTE CURRENT CONTROL SWITCH6. MAXIMUM OUTPUT CONTROL7. MINIMUM OUTPUT CONTROL AND DISPLAY

SWITCH7a. MENU BUTTON AND DISPLAY SWITCH8. DIGITAL METER AND DISPLAY SWITCH9. POSTFLOW TIME10. THERMAL SHUTDOWN LIGHT11. REMOTE RECEPTACLE12. TRIGGER SWITCH13. PULSE / SPOT MODE SWITCH14. PULSE FREQUENCY CONTROL 15. PULSE % ON TIME CONTROL16. PULSE BACKGROUND CURRENT CONTROL17. DOWNSLOPE TIME

WARNING

B-3


• When the Polarity Switch is set to DC (- or +), the TIG modeprovides high frequency only for starting.

Hi-Freq. turns on after pre-flow time with the arc start switchclosure, and turns off when the arc is established.*

• Also functions for DC+ polarity to permit "balling" of tung-sten for AC TIG welding.

4. AC BALANCE CONTROL – The potentiometer control permitsAC wave balance adjustment from Max. Penetration (~85%negative wave) with the control at Max. full CW position, toMax. Cleaning (~65% positive wave) with the control set nearminimum CCW position.

• Full minimum CCW position is the Auto Balance positionwhich is indicated by the Green panel light turning on. Thisfeature automatically provides the proper amount of cleaningand penetration for normal AC TIG welding

• The mid position is the Balanced position (~50% positiveand negative waves).

• The Balance control is only functional if the machine is set toAC polarity and TIG mode.

5. LOCAL/REMOTE CURRENT CONTROL SWITCH – A 2-positionswitch selects how the welding output is controlled for bothStick and TIG Modes:

• LOCAL (Top position) selects output control only by themachine panel Output Control. (See Item 6)

• REMOTE (Bottom position) selects output control to also beby an Amptrol (See Item 6), or other remote (10K pot) controlconnected to the Remote receptacle (See Item 11) Thisswitch selection is indicted by the Green panel light turningon.

In either position the arc start switch functions when connectedto the Remote receptacle (See Item 11).

6. MAXIMUM OUTPUT CONTROL – The large knob is used toset the output welding current over the rated output range ofthe machine.

• With the Current Control switch to LOCAL position, this knobsets the welding output level.

• With the Current Control switch to REMOTE position, thisknob sets the maximum welding level that the Peak outputcan be set with the remote Amptrol.

• The new MicroStartTM Technology minimum current circuitprovides for low end welding (down to 2 amps) previouslyunobtainable on an SCR platform TIG machine.

7. MINIMUM OUTPUT CONTROL AND DISPLAY SWITCH – A smallerknob is used to preset the minimum current level only for TIGmode. Pressing the Display (momentary) switch toggle left toMinimum Set position displays the Minimum control level set-ting on the Digital meter. (See Item 8)

• This knob sets the Start output level. When the arc lights(using a new built-in TIG start pulse) this level upslopesquickly (0.5 sec.w/ Advanced Panel, zero w/o-See UP Menuof Item 7a) and smoothly to the weld output level. The set-ting range for this Start control is the 2 amp minimum rangeof the machine up to about 50 amps, but no more than thelevel set by the Maximum Output control knob (See Item 6),but otherwise is independent of the Maximum setting.

• This setting also serves as the Crater-fill level, but with aPrecision TIG® Advanced Panel, it can be selected (seeSection B-7) to be either the Minimum Output control setting(same as Start setting) as shipped, or the minimum rating ofthe machine (2 amps).

• The Remote Amptrol range of control is between thisMinimum setting and the Maximum Output control knob set-ting, so these knobs can set the resolution of the Amptrol.Also, the Minimum setting serves as both the minimumAmptrol start level when the arc start switch is closed, aswell as the minimum Amptrol crater-fill level before the arcstart switch is opened to help prevent premature arc out andHi-Frequency re-initiation.

.• In STICK mode, the Start control is not functional since HotStart level is fixed, or internal Advanced Panel adjustable(see Section B-7). Pressing the Display (momentary) switchtoggle left to Minimum Output position displays minimumamps rating of the machine.

B-4


DIGITAL DISPLAYDIGITAL DISPLAY

SELECTSELECTDISPLAYDISPLAY

SET SETDISPLAYDISPLAY

7a MENU BUTTON AND DISPLAY SWITCH – Pressing and hold-ing the (Menu) Button for about 5 seconds enters the menudisplay which allows:

• Selection of up to seven programmable parameters(Preflow, Upslope, Hot Start, Arc Force, etc.) is displayed onthe digital meter by momentarily pressing and releasing theMENU button to step through the parameters.

• Setting of the desired level, displayed on the digital meterfor the selected parameter, by pressing the DISPLAY(momentary) switch toggle to the right to increase the levelsetting, or to the left to decrease it.

Setting:Selection 1:

01 *2

Selection 2:012 *345

Selection 3:0 *12∆

Description:HF (High Freq.)Scratch start TIG (No Hi-Freq.)Normal Hi-Freq. start and weldLift TIG (Touch start w/o Hi-Freq.)PF (Preflow time)No Preflow0.1 sec.0.5 sec.1.0 sec.1.5 sec.2.0 sec.SS (MicroStart™ Start Pulse)No AC pulse/Low DC pulse (soft start)High AC/DC pulse (forceful start)HS setting (see below) for each pulse when Pulsemode welding anodized aluminum.

TIG Mode Menu


0 *123456789

Selection 5:01*2345

Description:HS (TIG Hot Start % of output setting)+0% (Only setting for SS0, above.)+10%+20%+30%+40%+50%+60%+70%+80%+90%UP (Upslope Time)None (Only setting for SS1 & SS2, above.)0.5 sec.1.0 sec.1.5 sec.2.0 sec.2.5 sec.

TIG Mode Menu (with Advanced Control Panel installed):

* Default Factory Setting. (Indicated by "blinking" decimal point.)

* Default Factory Setting. (Indicated by "blinking" decimal point.)

∆ Only selectable with Advanced Control Panel installed.


012345 *6789

Selection 7:01 *23456789

Description:HS (Stick Hot Start % added to output setting)+0%+10%+20%+30%+40%+50%+60%+70%+80%+90%AF (Stick Arc Force % added to output setting)+0% ("Softer" arc)+10%+20%+30%+40%+50%+60%+70%+80%+90% ("Crisper" arc)

STICK Mode Menu (with Advanced Control Panel installed ◊ ):

* Default Factory Setting. (Indicated by "blinking" decimal point.)◊ If no Advanced Control Panel the Stick menu

displays “- - -“.

• Any of the following actions will exit the menu display:1. Pressing and holding the (Menu) Button again for about 5 seconds.2. Allowing the menu display to be unchanged for about 15 seconds.3. Closing the arc start switch (TIG Mode) or starting the arc (Stick Mode).Note: In Stick Mode the machine output will remain on while in menu display.

• Re-entering the menu displays the last parameter and setting that was displayed when the menu was exited.

• All settings may be reset to the Factory Default Settings (above) by holding the (Menu) button pressed while turning on themachine’s Power switch. The display will show “rES” to indicate the defaults are reset.

B-5


8. DIGITAL METER AND DISPLAY SWITCH– A (3- digit) LEDmeter is used to monitor the preset and actual welding proce-dure based on the Display (momentary) switch position:• Before welding with Display switch in center (normal) position,the digital meter displays the preset welding amps set byMaximum Output control knob (See Item 6). If in Stick modeusing REMOTE (See Item 5.), the digital meter displays the pre-set welding amps set by the Remote control. (See Item 11)

• While welding with Display switch in center (normal) position,the digital meter displays the actual welding amps with oneamp resolution (XXX) and accuracy within 4%+/-2A of reading.

• Any time in TIG mode and while pressing the Display switch toleft, the digital meter displays the amps preset by theMinimum Output control knob (See Item 7).

• Any time in Stick mode and while pressing the Display switchto left, the digital meter displays the minimum amps rating ofthe machine (See Item 7).

• Any time, in either mode, while pressing the Display switchright to Volts position, the digital meter displays actual outputvolts. Volts is displayed with 0.1 volt resolution (XX.X) andaccuracy within 3%+/-1V of reading.

• While pressing the (Menu) button when not welding (seeMenu Button and Display Button in previous section), forMeter and Display switch functions.

9. POSTFLOW TIME – This knob is used to set the TIG modeshielding gas postflow time over the range of about 2 to 60seconds after the arc is shut off. The postflow on time status isindicated by the Green panel light.

• Postflow Time is x2 extendable, if needed, by internal controlbox selection. (See Internal Set Up Controls)

• Gas preflow time for TIG mode is factory set at 0.5 second, butshorter times are selectable with the Menu Button andDisplay Button.

10. THERMAL SHUTDOWN LIGHT – This yellow LED panel lightturns on if the machine output is shutdown because internaloverheating has occurred, and turns off when the thermostatresets.

11. REMOTE RECEPTACLE – A 6-socket receptacle is provided forthe connection of an Amptrol, or other, remote control: (SeeFigure B.2)

• When the Current Control Switch, (See Item 5), is in theREMOTE position the Amptrol, or other remote (10K pot), con-nected to the Remote receptacle controls the TIG or Stickmode output within the range preset by the Maximum andMinimum Output controls. (See Item 6 and Item 7, also 8 formeter display)

• When the Current Control Switch is in either LOCAL orREMOTE positions the arc start switch functions when con-nected to the Remote receptacle.

ADVANCED PANEL CONTROLSThe following controls are included only if the Precision TIG®

275 has the Advanced Control Panel (K2621-1) option installed:(Refer to Section B-10 Tig Weld Cycle Chart for graphic illustra-tion of these TIG welding functions.)

12. TRIGGER SWITCH – This 2-position switch selects how thearc start switch ( connected to the above Remote receptacle)functions; in 2-Step or 4-Step mode:

• DO NOT USE 4-STEP IF USING AN AMPTROL REMOTE.• Neither the arc start switch nor the output control in theamptrol will function normally to shut off or control theout put. ONLY USE 2-STEP.

--------------------------------------------------------------------• In 2-Step position the arc start switch functions the same aswithout the Advanced Panel:

1. Closing switch starts preflow, then a fixed (0.5 sec.)ramp time from Minimum (Start) setting level (SeeItem 7) to Weld setting.

2. Opening switch initiates Downslope ramp time set-ting (See Item 17), from Weld setting to Crater-filllevel (See Item 7), which then stops the arc and ini-tiates Postflow time (See Item 9).

Note: See Section B-7 for 2-Step operation during Downslopewith Restart feature selected to be disabled, instead of enabled(as shipped).

A

B

C

D

E

F

Max

10K ohmMin

REMOTE RECEPTACLE *(Front View)

REMOTE OUTPUTCONTROL

ARC STARTSWITCH

*For 18-12P Plug(LECO S12020-27)

FIGURE B.2

CAUTION

B-6


• In 4-Step position allows welding without continuously holding thestart switch trigger. The arc start switch functions in the followingmanner:

1. Closing switch starts preflow, then arc starts at Minimum(Start) setting level (See Item 7). If the trigger is main-tained closed after preflow time the output remains at theStart level until it is released.

2. Opening switch initiates fixed (0.5 sec.) ramp time fromStart setting level to Weld setting.

3. Reclosing switch initiates Downslope ramp time setting(See item 17) from Weld setting down to the Crater-filllevel (See Item 7) of the machine.

4. Reopening switch after Downslope time holds Crater-filllevel until switch opens, then stops the arc and initiatesthe Postflow Time (See Item 9). Or, reopening switch dur-ing Downslope time immediately stops the arc and initi-ates the Postflow.

Note: (See Internal Set Up Controls) for 4-Step operation duringDownslope with Restart feature selected to be enabled, instead of dis-abled (as shipped).

13. PULSE/SPOT MODE SWITCH – Turns on the Pulse Mode as indicat-ed by the Green panel light turning on.

• PULSE ON provides a Peak current level set by REMOTE and/orLOCAL control of the output current (See Item5), for a time deter-mined by the Pulse Frequency Control setting (See Item 14) and the% ON Time (See Item 15). The balance of the cycle time is at theBackground Current level (See Item 16). The Green panel light blinksat the pulse frequency and time setting rate.

• Pulsing begins after upslope when the output current rises abovethe Background Current level and ends when the output currentdrops below this level.

• SPOT ON mode provides the peak current level set by the MaximumOutput Control for a time determined by the SPOT TIME control (seebelow). The red panel light is on for Spot mode.

14. PULSE FREQUENCY CONTROL – This knob is used to set the PulseFrequency over the peak pulse range of about 0.1 pps to 20 pps. (Onepulse cycle time = 1/pps = 10 to .05 sec. range.)

15. PULSE % ON TIME/SPOT TIME CONTROL – This knob sets thetime for Pulse or Spot modes:

• % ON TIME sets duration of the peak current as a percentage (5%to 95% on white scale) of one pulse cycle. The balance of the cycletime will be at the Background Current setting. (See Item 16)

• SPOT TIME sets the duration of the Spot pulse (0.5 to 5.0 secondson red scale).

16. PULSE BACKGROUND CURRENT CONTROL – This knob controlsthe level of the Background Current as a percentage (MIN.-100%)of the Peak (REMOTE and/or LOCAL) output level (See Item 6) downto the Minimum Output setting (See Item 7).

17. DOWNSLOPE TIME– This knob is used to set the time, over therange of zero to about 10 seconds, to ramp down from weld settingto Crater-fill level (See Item 7).

• If the arc goes out after the Downslope time is initiated, theDownslope time is interrupted and the Postflow time is initiated.This prevents Hi-Freq re-initiation during ramp down crater fill

• When using an Amptrol remote control, where the downslope iscontrolled by the operator down to the crater-fill level, theDownslope time should be set to zero so as not to have theDownslope time delay when the arc start switch is opened.

B-7


INTERNAL SET UP CONTROLS

Precision TIG® 275 models which have an Advanced Panel(K2621-1) option installed* have the following additional controlfeatures which are set up using the DIP Switch (S1) provided onthe internal panel of this option.

Access to this internal panel is obtained by removing the twoscrews securing the top corners of the Precision TIG® front con-trol panel and swinging the control panel down to reveal thepanel mounted on the surface of the Precision TIG® Controlboard:

• THE CONTROL BOARDS CONTAIN STATIC SENSITIVE COM-PONENTS

• To avoid possible damage to these components be sure toground yourself by touching the machine’s sheet metalwhile handling or making settings on the internal controlbox components.

--------------------------------------------------------------------

Precision TIG® ADVANCED PANEL(M21115 Internal Panel)

DIP SWITCH POSITIONS (FACTORY SETTINGS)

STICK WELDING FEATURES

• Switch #6 Hot Start Level – Does not function (See Item 7a)

• Switch #7 Arc Force Level – Does not function (See Item 7a)

TIG WELDING FEATURES

The following DIP switch feature selections function only whenthe Precision TIG® is set to TIG mode (See Item 3):

• Switch #1 Postflow Time Extension* (See Item 9)

ON – Doubles the time range.OFF – Standard time range (as shipped).

• Switch #2 2-Step Trigger Restart Feature (See Figure B.3)

ON – Restart Enabled (as shipped).OFF – Restart Disabled.

• Switch #3 4-Step Trigger Restart Feature (See Figure B.4)

ON – Restart Enabled.OFF – Restart Disabled (as shipped)

• Switch #4 Lift TIG Starting - Does not function (See Item 7a)

• Switch #5 Crater-Fill Level (See Item 7)

ON - Level is minimum rating of the machine (2A)OFF – Level (as shipped) is Minimum Output setting

(same as Start level).

* The Postflow Time doubling feature can also be selected on PrecisionTIG® 275 models without the Advanced Panel by accessing theControl board in the control box per above instructions, then discon-necting the jumper terminals attached to the jumper plug connectedto receptacle J3 of the Control board. (Refer to Machine WiringDiagram.)

CAUTION

HOT STARTARC FORCE

^ ON

1 2 3 4 5 6 7

DIP SWITCH (S1)

S F

ON

OFF

1 2 3 4 5 6 7

(DOES NOT FUNCTION)

B-8


(With DIP Switch #2 ON, As Shipped)

(With DIP Switch #2 OFF)

FIGURE B.3

B-9


FIGURE B.4

(With DIP Switch #3 OFF, As Shipped)

(With DIP Switch #3 ON)

B-10


SETUP GUIDELINES FOR TIG WELDING WITH ANAMPTROL

Both the Hand and Foot AMPTROLS work in a similar manner.They are meant to be used for remote current control for TIGwelding using the machine’s 2-Step trigger mode (See Item 12).

The Amptrol is capable of controlling the output of the PrecisionTIG® over the range between the level preset by the MinimumOutput control when the Amptrol is at its inactivated state, andthe level preset by the Maximum Output control when theAmptrol is at fully-activated state.

It is important to note that even with the Precision TIG®’s newMicroStartTM Technology, some tungstens may be difficult tostart at the low (2 amps) minimum rating of the machine. Ratherthan guessing where to depress the Amptrol to start the arc reli-ably, the Minimum Output control allows presetting the exactlevel, so reliable starts, as well as minimum crater-fill levels, canbe consistently obtained at the minimum Amptrol (inactivated )state. FIGURE B.6 shows Precision TIG® setup for TIG weldingwith an Amptrol.

TIG WELD CYCLE CHART

SEE ITEM 12 SEE ITEM 12

SEE ITEM 7a

SEE ITEM 12 SEE ITEM 12

SEE ITEM 7

SEE ITEM 9SEE ITEM 17

SEE ITEM 16

SEE ITEM 15

SEE ITEM 15

SEE ITEM 14

SEE ITEM 7a

SEE ITEM 12

SEE ITEM 7a

SEE ITEM 7

SEE ITEM 6

SEE ITEM 6 & 7

SEE ITEM 12 & TIGWelding Features

B-11


Max. to Min.Amptrol

Min. to Max.Amptrol

Setup for TIG Amptrol Welding

Advanced Panel(If used)

Standard Controls

Power SwitchON

Polarity SwitchAC or DC-

Mode SwitchTIG

AC BalanceAUTO

orSet:

More + for alum.oxide "Cleaning" w/o "Spitting" or "wetting" loss.

Balanced for equal + and - current.More - for higher "Penetration".

Local/RemoteSwitch

REMOTE

Trigger Switch2-STEP

Pulse SwitchON or OFF

Pulse Frequency4-6 pps is a typical initial setting.

Set for bead shape and travel speed:Higher for thinner plate and faster travel.Lower for thicker plate and slower travel.

% On Time40-60% is a typical initial setting.

Set for total heat of Peak current:Lower reduces distortion and burn-thru.

Background Current40-60% is a typical initial setting.

Set as low as will maintain a pulse arc(Will not drop below Min.Output setting.)

DownslopeZERO

For no arc-out delay.

Minimum OutputPress Display switch

and Set to desired min.Amptrol (Start/Crater)

output level.

PostflowSet as low as required.

Higher for largertungsten and current.

Maximum OutputSet to desired max.

Amptrol output level.

FIGURE B.6

B-12


RECOMMENDED ELECTRODE AMPERAGE RANGES - Precision TIG® 275

SMAW Process ELECTRODE POLARITY 3/32" 1/8" 5/32"Fleetweld 5P, Fleetweld 5P+ DC+ 40 - 70 75 - 130 90 - 175Fleetweld 180 DC+ 40 - 80 55 - 110 105 - 135Fleetweld 37 DC+ 70 - 95 100 - 135 145 - 180Fleetweld 47 DC- 75 - 95 100 - 145 135 - 200Jet-LH MR DC+ 85 - 110 110 - 160 130 - 220Blue Max Stainless DC+ 40 - 80 75 - 110 95 - 110Red Baron Stainless DC+ 40 - 70 60 - 100 90 - 140Mild steel procedures are based on recommended procedures listed in C2.10 8/94 and the maximum rating of the Precision TIG® 275Excaliber 7018 procedures are based on Jet-LH 78 MRBlue Max procedures are based on C6.1 6/95Red Baron Procedure are based on ES-503 10/93

GTAW Process Electrode Polarity DC- AC* Approximate Argon Electrode Tip Preparation Sharpened Balled Gas Flow Rate Electrode Type EWZr C.F.H. (l/min.) EWTh-1, EWCe-2 EWTh-1, EWTh-2 EWTh-2, EWLa-1 EWP EWCe-2, EWLa-1 StainlessElectrode Size (in.) EWG EWG Aluminum Steel .010 Up to 15 A. Up to 15 A. Up to 15 A. 3-8 (2-4) 3-8 (2-4) .020 Up to 15 A. 10 to 15 A. 5 to 20 A. 5-10 (3-5) 5-10 (3-5) .040 Up to 80 A. 20 to 30 A. 20 to 60 A. 5-10 (3-5) 5-10 (3-5) 1/16 Up to 150 A. 30 to 80 A. 60 to 120 A. 5-10 (3-5) 9-13 (4-6) 3/32 Up to MAX. A. 60 to 130 A. 100 to 180 A. 13-17 (6-8) 11-15 (5-7) 1/8 X 100 to 180 A. 160 to 250 A. 15-23 (7-11) 11-15 (5-7)

Tungsten electrodes are classified as follows by the American Welding Society (AWS):

Pure .................................................EWP ...............green

+1% Thoria ......................................EWTh-1..........yellow

+2% Thoria ......................................EWTh-2..........red

+2% Ceria........................................EWCe-2 .........orange

+1.5% Lanthana ..............................EWLa-1..........black

+0.15 to 0.40% Zirconia ..................EWZr..............brown

Ceriated Tungsten is now widely accepted as a substitute for 2% Thoriated Tungsten in AC and DC applications.

Balanced Wave, Unbalanced Wave requires derating of the electrode.

MAKING A TIG WELD WITH AN AMPTROL

1. Install welding equipment per Section A-5.

2. Setup controls per Section B-10.

3. Turn on the shielding gas supply, and torch coolant inputsupply (if used).

Note: The Precision TIG® Under-Cooler (or Water Solenoid connect-ed to the Cooler receptacle) runs with the Fan-As-Neededmachine cooling fan (See Maintenance Section D), so thecooler fan and water pump will also not run continuously inidle, but will run while welding.

4. With the torch held safely away from everything, close theArc Start Switch of the Amptrol and set the gas flow meter.Then open the switch. The welder is now ready for welding.

5. Position the tungsten electrode at the start of the weld at a65° to 75° angle with the horizontal, in the direction of push-ing travel, so that the electrode is approximately 1/8" (4 mm)above the work piece.

Close the arc start switch. This opens the gas valve to auto-matically purge air from the hose and torch, then shields thearc strike area. After the 0.5 second preflow time, the highfrequency becomes available to strike the arc. When the arcstrikes the torch coolant (if used) starts to flow. Also, if weld-ing DC- TIG, the high frequency shuts off just after the arcstrikes.

6. Hold the arc start switch closed at minimum Amptrol Startlevel (See Section B-10) until an arc is established, thenincrease the output to the desired welding level and push thetorch in the direction of travel.

7. At the end of the weld, decrease the Amptrol output to thecrater-fill level before releasing the arc start switch to startthe Postflow time. Hold the torch gas shielding over thesolidifying weld crater while postflow time expires and thegas valve reopens. The torch coolant (if used) continues toflow for up to 8 minutes after the arc goes out (with the Fan-As-Needed feature) to assure torch cooling.

• Repeat steps 5 through 7 to make another weld.

*

C-1

ACCESSORIESPRECISION TIG® 275

OPTIONAL EQUIPMENT

FACTORY INSTALLED OPTIONS

The basic Precision TIG® 275 machine is factory equipped with:

• A 3/8" Adapter (S20403-4) for air cooled torch connection ofa PTA-9 or PTA-17.

FIELD INSTALLED OPTIONS

The following Options/Accessories are available for the PrecisionTIG® 275 and are installed per instructions in this manual and /or provided in the package:

• K2621-1 Precision TIG® Advanced Control Panel Provides 2/4-step trigger modes with adjustable Pulser/Spot con-trols and Down slope timer for TIG welding. Alsoallows adjustable Hot Start and Arc Force Menu set-tings for Stick welding and Menu settings for TIGHot Start and Upslope, as well as other user selec-table features.

• K1828-1 Under-Cooler Cart Includes a "cooler-in-a-drawer" with hoses and a lockablestorage drawer on a dual bottle undercarriage (see below).

• K1869-1 UndercarriageIncludes a dual bottle rack with chain and an undercarriagewith 5" front casters,10" rear wheels and a handle.

• K1830-1 Water Solenoid KitProvides for stopping flow of external water supply. Connectsto coolant inlet and cooler receptacle of Precision TIG®.(Can not be used with a water cooler.)

• K870 Foot AmptrolSingle pedal foot activation of arc start switch and output con-trol, with 25’ plug cable.

• K963-3 Hand AmptrolFastens to torch for convenient thumb activation of arc startswitch and output control, with 25’ plug cable:

• K814 Arc Start SwitchNeeded for TIG welding without an Amptrol. Includes 25’ plugcable, and attaches to torch for convenient finger control.

• K1831-1 Power Factor Capacitor KitUsed when welding at higher output currents to reduce inputcurrent and help keep electricity costs to a minimum.

• Magnum® PTA and PTW Series TorchesAll Air Cooled or Water-Cooled Magnum® TIG Torches may beused with the Precision TIG® 275. Connection adapters areonly required for Air-Cooled Torches (Refer to Diagrams onA-7) INSTALLATION SECTION:

K2166-1 7/8” Torch Connector for PTA-26 (one piece)

K2166-2 1/2” stud Connector for PTA Torch (two-piece).

K2166-3 3/8” TIG Torch Connector for PTA-9,-17 (one piece).(Included as S20403-4 with Precision TIG® models.)

• 3100211 Harris Argon Flow Regulator (Includes 10’ hose.)

• K2150-1 Work Lead Assembly15ft. 2/0 cable with 1/2" stud lug and work clamp.

D-1

MAINTENANCEPRECISION TIG® 275

ELECTRIC SHOCK can kill.

• Only qualified personnel should perform this maintenance.

• Turn the input power OFF at the disconnect switch or fuse box before working on this equipment.

• Do not touch electrically hot parts.

To avoid receiving a high frequency shock, keep the TIGtorch and cables in good condition.

Very little routine maintenance is necessary to keep yourPrecision TIG® 275 running in top condition. No specific sched-ule can be set for performing the following items; factors suchas hours of usage and machine environment should be consid-ered when establishing a maintenance schedule.

• Periodically blow out dust and dirt which may accumulatewithin the welder using an air stream.

• Inspect welder output and control cables for fraying, cuts,and bare spots.

• Inspect the spark gap at regular intervals to maintain the rec-ommended spacing. See the Service Procedures (See ServiceProcedures in this Section) for complete information on sparkgap settings.

• The fan motor has sealed ball bearings which require nomaintenance.Overload Protection

SAFETY PRECAUTIONS

ROUTINE AND PERIODIC MAINTENANCE

OVERLOAD PROTECTION

FAN-AS-NEEDED (F.A.N.)

The Precision TIG® 275 has the F.A.N. circuit feature, whichmeans the cooling fan will operate only while welding; then forabout 8 minutes after welding has stopped to assure propermachine cooling. This helps reduce the amount of dust and dirtdrawn into the machine with the cooling air. The cooling fan willoperate briefly when the machine power is initially turned on,and continuously while the yellow Thermal Shutdown Light is lit(see Thermostatic Protection).

THERMOSTATIC PROTECTION

This welder has thermostatic protection from excessive dutycycles, overloads, loss of cooling, and excessive ambient tem-peratures. When the welder is subjected to an overload, or inad-equate cooling, the primary coil thermostat and/or secondarycoil thermostat will open. This condition will be indicated by theillumination of the yellow Thermal Shutdown Light on the frontpanel (see Item 10 in Section B). The fan will continue to run tocool the power source. Postflow occurs when TIG welding isshut down, but no welding is possible until the machine isallowed to cool and the yellow Thermal Shutdown Light goesout.

AUXILIARY POWER CIRCUIT BREAKER

This machine includes a 5 amp circuit breaker, located on theopposite side of the upper case back, for protection of the220vac Schuko type cooler receptacle.

WARNING

WARNING

D-2


SERVICE PROCEDURES

Operation of the Precision TIG® should be trouble-free for the lifeof the machine. Should a malfunction occur, however, the follow-ing procedures will be useful to trained service personnel withexperience in repairing arc welding equipment:

COMPONENT ACCESSThe following components are accessible for routine set up andperiodic service without requiring removal of the case sides orroof:

• Input Reconnect Panel (refer Section A) is located behind aremovable panel on the rear of the left case side. Remove thetwo screws (with a screwdriver or a 3/8"/ 9.5mm hex driver)on the bottom corners of this panel to remove it.

• Control Box components and PC Boards (refer Section BInternal Set Up Controls) are located behind the front controlpanel. Remove the two screws (with a screwdriver or a 3/8"/9.5mm hex driver) on the top corners of this panel to swing itdown.

• Hi-Freq. Spark Gap assembly (refer Spark Gap Adjustment) islocated behind a removable panel on the rear of the right caseside, under the torch box. Remove the screw (with a screwdriv-er or a 3/8"/ 9.5mm hex driver) on the bottom center of thispanel to remove it.

SPARK GAP ADJUSTMENT

The spark gap is set at the factory to a gap of 0.015 inches (0.4mm) See Figure C.1. This setting is adequate for most applica-tions. Where less high frequency is desired, the setting can bereduced to 0.008 inches (0.2 mm).

Use extreme caution when working with circuit of the highfrequency. The high voltages developed can be lethal. Turnthe input power off using the disconnect switch or fuse boxbefore working inside the machine. This is particularlyimportant when working on the secondary circuit of the highvoltage transformer (T3) because the output voltage is dan-gerously high.--------------------------------------------------------------------

Note: In highly dirty environments where there is an abundanceof conductive contaminants, use a low pressure air streamor a firm piece of paper to clean out the spark gap. Do notdisturb the factory gap setting.

To check the spark gap:1. Turn the input power off per above.2. Remove the access panel on the right case side (See

Component Access).3. Check the spark gap spacing with a feeler gauge.

If adjustment is required:1. Adjust the gap by loosening the Allen head screw on one of the

aluminum blocks, reset the gap and tighten the screw in thenew position.

If spark gap is correct:1. Reinstall the access panel on the right case side.

UNDER-COOLER SERVICE

The required maintenance and service instructions for the Under-Cooler are provided in the operator’s manual (IM723) providedwith the Under-Cooler Cart.

.015 Spark Gap

FIGURE C.1 SPARK GAP

WARNING

D-3


METER CALIBRATION ADJUSTMENT

The Precision TIG® meter circuits are factory calibrated for theaccuracy of the ammeter and voltmeter (see Section B PanelControl Functions), and should not need adjustment. However,the factory trimmers are accessible inside the control box (seeSection D Component Access):

• The Meter Board, located on the front panel of the machine,is digital and has no calibration capability.

• Ammeter Calibration Trimmer (R5) is located on the ControlPC Board (left of center near the top of the board). This trim-mer adjusts calibration of the ammeter circuit to the digitalpanel Meter, so it should be checked after the Digital Metercheck above. The ammeter calibration is checked as follows:

1. Set to TIG mode with DC- polarity and LOCAL con-trol. Without closing the arc start switch, preset theMaximum Output panel control so the panel digitalMeter reads about 200 amps.

2. Using a DC (avg.) test ammeter with at least 1%accuracy at up to 300 amps, connect it to measurethe DC current through a short weld cable shortingout the WORK (+) to ELECTRODE (-) studs on thefront stud panel. Remove the TIG torch, if connect-ed.

3. Close the arc start switch just long enough to com-pare the panel Meter reading to that of the testammeter. The short circuit current readings shouldmatch within 4%+/-2A. If not, adjust the trimmer sothat the panel meter accuracy is corrected.

• Voltmeter Calibration Trimmer (R2) is located on theControl PC Board (right of center near the top of the board).This trimmer adjusts calibration of the voltmeter circuit to thedigital panel Meter, so it should be checked after the DigitalMeter check above. The voltmeter calibration is checked asfollows:

1. To prevent maximum OCV output (which is not pre-cise for voltmeter checking) disconnect the SCRgate lead plug from receptacle J4 on the lower leftcorner of the Control PC board.

2. Set to TIG mode with DC- polarity without closingthe arc start switch.

3. Using a DC (avg.) test voltmeter with at least 1%accuracy at up to 100 volts, connect it across theWORK (+) and ELECTRODE (-) studs on the frontstud panel. Remove the TIG torch, if connected.

4. Press the DISPLAY panel switch to V (volts) position,then close the arc start switch just long enough* tocompare the panel Meter reading to that of the testvolt meter. The open circuit voltage readings (about50vdc) should match within 3%+/-1V. If not, adjustthe trimmer so that the panel meter accuracy is cor-rected.

* If switch is held closed longer than about 15 seconds thePrecision TIG® will shut down to protect internal holding resis-tor from overheating.

If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln AuthorizedField Service Facility for technical troubleshooting assistance before you proceed.

This Troubleshooting Guide is provided to help you locate andrepair possible machine malfunctions. Simply follow the three-step procedure listed below.

Step 1. LOCATE PROBLEM (SYMPTOM).Look under the column labeled “PROBLEM (SYMPTOMS)”. Thiscolumn describes possible symptoms that the machine mayexhibit. Find the listing that best describes the symptom that themachine is exhibiting.

Step 2. POSSIBLE CAUSE.The second column labeled “POSSIBLE CAUSE” lists the obviousexternal possibilities that may contribute to the machine symp-tom.

Step 3. RECOMMENDED COURSE OF ACTIONThis column provides a course of action for the Possible Cause,generally it states to contact your local Lincoln Authorized FieldService Facility.

If you do not understand or are unable to perform theRecommended Course of Action safely, contact your local LincolnAuthorized Field Service Facility.

DO NOT use a volt-ohm meter to measure output voltages in TIG mode. The High FrequencyArc Starter voltage can damage the meter.

E-1TROUBLESHOOTINGE-1

HOW TO USE TROUBLESHOOTING GUIDE

Service and Repair should only be performed by Lincoln Electric Factory Trained Personnel. Unauthorized repairs per-formed on this equipment may result in danger to the technician and machine operator and will invalidate your factorywarranty. For your safety and to avoid Electrical Shock, please observe all safety notes and precautions detailed throughoutthis manual.

__________________________________________________________________________

WARNING

CAUTION

CAUTION

OUTPUT PROBLEMS

Thermal light comes on.

Meter doesn’t light up.

Has output in No gas & no hi-freqStick mode but no output in Tig mode.

Gas & hi-freq are o.k.

No output in both Stick and Tig modes.

1. Thermal shut down. Dirt and dust mayhave clogged the cooling channels insidemachine; air intake and exhaust louversmay be blocked; welding application mayexceed recommended duty cycle. Waituntil machine cool down and thermallight goes out. Blow out machine withclean, dry low pressure air; check airintake and louvers; stay within recom-mended duty cycle.

2. Bad thermostat or its connections.

1. Losing AC supply to Control PC board.

2. Loosing input to machine.

3. Faulty Control PC board.

1. Faulty trigger or hand/foot Amptrolor connections.

2. Faulty Protection PC board or bad con-nection to Control PC board.

3. Losing trigger supply to Control PCboard.

1. Faulty Control PC board

1. Bad connection at P4 of Control PCboard.


If all recommended possible areas of mis-adjustment have been checked and theproblem persists, Contact your localLincoln Authorized Field Service Facility.

E-2

TROUBLE SHOOTING

Observe all Safety Guidelines detailed throughout this manual

If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your LocalLincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.

PROBLEMS(SYMPTOMS)

POSSIBLE CAUSE

RECOMMENDEDCOURSE OF ACTION

PRECISION TIG® 275

CAUTION

METER PROBLEMS

PROBLEMS(SYMPTOMS)

POSSIBLE CAUSE


Meter does not light up.

Meter does not display V (Volt) or Min A(Minimum current).

No gas.

No control on post flow time.

Pre flow & Post flow time too long.

1. Bad meter or its connection.



1. Bad Display switch or its connection.


1. Circuit breaker CB1 open. Press CB1 into reset.


3. Faulty gas solenoid valve SV1 or its con-nection.


1. Faulty potentiometer R3 or its connec-tion.


1. For Postflow; the DIP switch setting on theAdvanced Control PCB (if installed) maybe set for time x2. Check DIP switch set-ting.

2. For Preflow; Menu setting too long. CheckMenu setting.

3. Missing plug P3 on Control board or badconnection of P3 to Advanced ControlPCB.



E-3

TROUBLE SHOOTING



PRECISION TIG® 275

CAUTION

GAS PROBLEMS

HI-FREQ PROBLEMS

PROBLEMS(SYMPTOMS)

POSSIBLE CAUSE


No hi-freq.

Hi-freq intensity too weak.

Hi-freq on continuously in DC Tig.

Hi-freq shuts off after starting in AC Tig.

1. Circuit breaker CB1 open.


3. Spark gaps shorted.


1. Dirty spark gap or improper gap setting.

2. Faulty Arc Starter assembly.


2. Micro-switch S2A is not engaged & disen-gaged properly when switching betweenDC & AC polarity. (S2A locates on thePolarity switch).


1. Micro-switch S2A is not engaged & disen-gaged properly when switching betweenDC & AC polarity. (S2A locates on thePolarity switch).


E-4

TROUBLE SHOOTING



PRECISION TIG® 275

CAUTION

PRESET & OUTPUT CONTROL PROBLEMS

PROBLEMS(SYMPTOMS)

POSSIBLE CAUSE


Meter does not display preset.

High output current in both DC & AC polari-ties regardless of preset.

High output current in DC polarity regardlessof preset, o.k. in AC polarity.

In 2-step Tig, output stays on for more thandownslope time after trigger open (machinewith Advanced Control panel only).

Output stays on after releasing hand/footAmptrol (machine with Advanced Controlpanel only).

1. Faulty potentiometer R1 or its connection.

2. Bad connection at P9 of Control PC board.

3. Faulty Advanced Control PC board ( if pre-sent ) or its connection to the main ControlPC board.

4. Missing plug P3 on Control board or badconnection at P3 when an AdvancedControl PC board is not present.

1. Bad connection at P6 of Control PC board.

2. Bad shunt connection.


4. Faulty SCR bridge.

1. Shorted free wheeling diode D1.

1. Bad 2/4 step switch or its connection.

2. Bad connection at P1 of Advanced ControlPC board.

1. Downslope is not set at min.

2. Bad Downslope potentiometer R12 or itsconnection.


E-5

TROUBLE SHOOTING



PRECISION TIG® 275

CAUTION

E-6

TROUBLE SHOOTING


PRECISION TIG® 275

CAUTION


STICK WELDING PROBLEMS

PROBLEMS(SYMPTOMS)

POSSIBLE CAUSE


Stick electrode "blast off" when arc isstruck.

Stick electrode "sticks" in the weld puddle.

Poor starting in DC polarity.

Arc "flutters" in DC polarity, o.k. in ACpolarity.

Arc "flutters" in both DC & AC polarities.

1. Current may be set too high for electrodesize.

2. (Machine with Advanced Control PC boardonly) Hot Start Menu setting too high.

1. Current may be set too low for electrodesize.

2. (Machine with Advanced Control PC boardonly) Arc Force Menu setting too low.

1. Input line may be too low.


3. Bad Background rectifier, backgroundresistor R7, or background diode D2.

1. Tungsten not "sharp".

2. Bad free wheeling diode D1 or its connec-tion.

1. Tungsten electrode may be too large indiameter for the current setting.

2. Gas shielding may be insufficient.

3. Contaminated gas or leaks in the gas line,torch, or connections.

4. Helium blend is used as a shielding gas.



TIG WELDING PROBLEMS

E-7

TROUBLE SHOOTING


PRECISION TIG® 275

CAUTION


TIG PROBLEMS

PROBLEMS(SYMPTOMS)

POSSIBLE CAUSE


Arc "pulsates" in AC polarity, DC polarity iso.k..

Black area along weld bead.

Output quits momentarily; gas flow and hi-freq are also interrupted.

1.Micro switch S2A on polarity switch doesnot open in AC polarity.

1. Oily or organic contamination from workpiece.

2. Tungsten electrode may be contaminated.

3. Leaks in gas line, torch, or connections.

1. May be caused by hi-freq interference.Check that machine is grounded properly.Surrounding machines that generate hi-freq also should be properly grounded.

2. Ground connection of Protection PC boardmay has become loose.

3. Ground connection of Bypass/StabilizerPC board may has become loose. If all recommended possible areas of mis-

adjustment have been checked and theproblem persists, Contact your localLincoln Authorized Field Service Facility.

F-1

WIRING DIAGRAMPRECISION TIG® 275

NOTE: This diagram

is fo

r reference only. It m

ay not be accurate fo

r all machines covered by th

is m

anual. The specific diagram

for a

particular code is pasted inside th

e machine on one of th

e enclosure

panels. If the diagram is illegible, write to th

e Se

rvice De

partm

ent for a re

placem

ent. Give the equipm

ent c

ode number..

F-2

DIMENSION PRINTPRECISION TIG® 275

L11660

XB-UF

** LO

CATI

ON

OF

(4) O.

284

BASE

MO

UNTI

NG H

OLE

S.

12.77

31.00

26.00

1.00

24.00

**

.28

3.47

20.50

**

22.00

.30

.75

3.44

TORC

H HO

LSTE

R

2.11

TORC

H BO

X

11.00

2.98

F-3

NOTES

Precision TIG 275 - 12490

ii

THIS PAGE INTENTIONALLY LEFT BLANK

KEY PART NUMBER DESCRIPTION QTYP-897-A Index of Sub Assemblies AR

P-897-B.2 Miscellaneous Items AR

1 P-897-C Case Front Assembly AR

2 P-897-D Arc Starter & Bypass Assembly AR

3 P-897-E Case Back Assembly AR

4 P-897-F Center Assembly AR

5 P-897-G Cover Assembly AR

Index of Sub Assemblies - 12490

Precision TIG 275 - 12490 1

Prin

ted

12/0

7/20

15 a

t 15:

16:1

0. P

rodu

ced

by E

nigm

a.

P-897-A.jpg

Index of Sub Assemblies - 12490

2 Precision TIG 275 - 12490

Prin

ted

12/0

7/20

15 a

t 15:

16:1

0. P

rodu

ced

by E

nigm

a.

KEY PART NUMBER DESCRIPTION QTY9SS18250-931 PLUG & LEAD ASBLY 1

9SL10882-2 BYPASS PC BD ASBLY 1

9SS19655-2 RECEPTACLE & LEAD ASBLY 1

9ST13657-3H24 LED FORMED 3

9ST13657-4FA YELLOW LED 1

9ST13657-2H24 LED-T-1 3/4REDHLMP-3301-F00dd 1

9SG5784 HARNESS ASBLY 1

9SS18543-4 INPUT CABLE GROMMET 1

9SG5698 CASEBACK 1

9SS18543-4 INPUT CABLE GROMMET 1

9ST12380-1 BUSHING 1

Miscellaneous Items


Prin

ted

12/0

7/20

15 a

t 15:

16:1

0. P

rodu

ced

by E

nigm

a.

No Image

Miscellaneous Items


Prin

ted

12/0

7/20

15 a

t 15:

16:1

0. P

rodu

ced

by E

nigm

a.

KEY PART NUMBER DESCRIPTION QTY1 9SG3960 CASE FRONT WELDED ASBLY 1

2 9SG4030 TOP BEZEL 1

3 9SS9225-89 THREAD FORMING SCREW 4

4 9ST14882-1 DOOR BUMPER 2

9SL12927-1 Control Panel Assembly 1

5A 9SL12926 CONTROL PANEL 1

10 9SG6374 NAMEPLATE 1

5C 9ST10800-49 SWITCHTOGGLESPDT 1

5D 9ST10800-4 SWITCH 4

9SL12958-1 CONTROL PANEL HARNESS 1

5E 9ST10812-119 POTENTIOMETER 4

9ST15089-1 SWITCH;PUSHBUTTON 1

5H 9SS18280 POTENTIOMETER SPACER 4

5J 9ST13639-3 KNOB 3

5K 9ST10491-1 KNOB 1

5L 9SM15893-3 METER PC BOARD ASBLY 1

5M 9SS23093-1 LED LENS CLEAR 5

9SS23094-1 RETAINING O RING 5

9SM21089 OPTION PANEL 1

9ST9187-13 #10-24HLN-1817/1-NYLON INSERT 4

10 9SG6374 NAMEPLATE 1

5T 9SS9225-92 THREAD FORMING SCREWCUTTING(1/4-20X.50) 2

6 9SG3526 TOOL TRAY 1

7A 9SS7670 SWITCH ASBLY 1

20C 9SS8025-115 SELF TAPPING SCREW 8

8A 9SS13100-264 CONNECTOR & LEAD ASBLY 1

8B 9SS8025-113 SELF TAPPING SCREW 2

9A 9SL11604 DOOR 1

9B 9SS22921 PIN (DOOR) 2

9SS9262-30 PLAIN WASHER 1

9SE106A-14 LOCKWASHER 1

9E 9ST9187 LOCKNUT 2

23 9SL13115 DECAL 1

9G 9SS9225-87 THREAD FORMING SCREW 2

Case Front Assembly


Prin

ted

12/0

7/20

15 a

t 15:

16:1

0. P

rodu

ced

by E

nigm

a.

KEY PART NUMBER DESCRIPTION QTY10 9SG6374 NAMEPLATE 1

11A 9SS18250-774 PLUG & LEAD ASBLY 1

11B 9SS18543-4 INPUT CABLE GROMMET 1

9SS16656-4 OUTPUT TERMINAL ASBLY 2

15B 9SS9225-88 THREAD FORMING SCREW 1

12C 9ST3960 FLANGE NUT 2

13A 9SL7390-1 POLARITY SWITCH ASBLY 1

13B 9SCF000017 1/4-20HN 2

13C 9ST9860-6 LOCKWASHER 2

14A 9SS18234 POLARITY SWITCH JUMPER 1

18B 9SCF000029 5/16-18HN 1

15A 9SM15248 HANDLE-MOLDED 1


17 9SS18250-777 PLUG & LEAD ASBLY 1

18B 9SCF000029 5/16-18HN 1



20A 9SG4763-1 CONTROL PC BD ASBLY 1

20B 9SS14020-10 PLASTIC EXPANSION NUT 8


23 9SL13115 DECAL 1

23 9SL13115 DECAL 1

23 9SL13115 DECAL 1

28A 9ST13637-6 DIODE-BRIDGE35A400VF-W1-PH 1

28B 9SS9225-36 THREAD FORMING SCREW (CUTTING) 1

28D 9ST9695-1 LOCKWASHER 1

28E 9SCF000010 #10-24HN 1

29A 9SM16062-2 PROTECTION PC BD ASBLY 1

29B 9ST10082-27 SEMS SCREW 3

Case Front Assembly


Prin

ted

12/0

7/20

15 a

t 15:

16:1

0. P

rodu

ced

by E

nigm

a.

P-897-C.jpg

Case Front Assembly


Prin

ted

12/0

7/20

15 a

t 15:

16:1

0. P

rodu

ced

by E

nigm

a.

KEY PART NUMBER DESCRIPTION QTY9SL11597-2 ARC STARTER & BYPASS ASBLY 1

1 9SM19835 ARC STARTER ASBLY 1

2 9SL10121-1 BYPASS/STABILIZER PC BD ASBLY 1

3A 9ST11827-23 CARRIAGE BOLT 2

13B 9SS9262-98 PLAIN WASHER 1


13D 9SCF000017 1/4-20HN 1

4 9SL11650 ARC STARTER SUPPORT 1

5A 9SS14020-3 PLASTIC EXPANSION NUT 2


6A 9SS14020-1 PLASTIC EXPANSION NUT 2


7A 9ST9447-21 SOCKET HEAD CAP SCREW 1



8 9SCF000010 #10-24HN 2

9 9ST12380-8 BUSHING 2

10A 9SS16876 SPARK GAP ASBLY 1


10C 9ST11236-1 ELECTRODE 2

11 9ST10082-12 SEMS SCREW 2

12 9ST12380-3 BUSHING 1

13A 9SS25215 HIGH FREQUENCY LEAD 1



13D 9SCF000017 1/4-20HN 1

14 9SS9225-92 THREAD FORMING SCREWCUTTING(1/4-20X.50) 1

Arc Starter & Bypass Assembly


Prin

ted

12/0

7/20

15 a

t 15:

16:1

0. P

rodu

ced

by E

nigm

a.

P-897-D.jpg

Arc Starter & Bypass Assembly


Prin

ted

12/0

7/20

15 a

t 15:

16:1

0. P

rodu

ced

by E

nigm

a.

KEY PART NUMBER DESCRIPTION QTY9SG5652-1 Case Back Asbly 1

1 9SG5649-1 CASEBACK 1

2A 9SL11587 FAN SHROUD 1

26B 9SS9225-92 THREAD FORMING SCREWCUTTING(1/4-20X.50) 5

3A 9SM20039 FAN BRACKET 1


4A 9SS25857-2 FAN & TERMINAL ASBLY 1

4B 9SM8678-2 FAN BLADE 1

4C 9SS9262-3 PLAIN WASHER 2

4D 9ST4291-A LOCKWASHER 2

4E 9SCF000042 #8-32HN 2

6A 9SS11668-1 RECEPTACLE 1

6B 9SCF000010 #10-24HN 2

6C 9SS9225-36 THREAD FORMING SCREW (CUTTING) 2

7 9ST12287-22 CIRCUIT BREAKER-15A 1

33 9SL13115 DECAL 1

9A 9SM19774 FILLER ROD HOLDER AND AIR BAFFLE 1


9ST12584-6 RIVET 1

10 9ST13259-2 GROUNDING DECAL 1

33 9SL13115 DECAL 1

12 9SS19450 BY-PASS ASBLY 1

33 9SL13115 DECAL 1

33 9SL13115 DECAL 1

33 9SL13115 DECAL 1

9ST12287-30 CIRCUIT BREAKER-5.0A 1

15A 9SL11584 TORCH CONNECTION BOX COVER ASBLY 1


15C 9SS25305 MAGNETIC CATCH LATCH 1

9SL12925-1 Torch Connection Box Asbly 1

17 9SL12924 TORCH CONNECTION BOX 1

18A 9SS24629 TORCH CONNECTION STRAP 1

18B 9SCF000140 5/8-11HJN 2


Case Back Assembly


Prin

ted

12/0

7/20

15 a

t 15:

16:1

0. P

rodu

ced

by E

nigm

a.

KEY PART NUMBER DESCRIPTION QTY18D 9SS9262-41 PLAIN WASHER 2

19 9ST14557-8 HOSE NIPPLE-MALE 2

20A 9SM13896-8 OUTPUT TERMINAL MOLDING 1


21A 9SM13896-6 OUTPUT TERMINAL MOLDING (LH) 1


22A 9ST14557-15 CONNECTOR 3

22B 9ST9695-8 LOCKWASHER 3

22C 9SCF000054 1/2-13HJN 3

23A 9ST10642-255 FLEX TUBE 3

23B 9SS20710-6 HOSE CLAMP 6

24 9SM17294-10 SOLENOID VALVE ASBLY 1


9ST14370-1 CONDUIT LOCKNUT 1

25 9ST12380-8 BUSHING 1

26A 9SM19793 TORCH CONNECTION PANEL 1


27 9ST12380-3 BUSHING 1

28A 9SS15122-14 RELAY 1


29 9ST14798-4 IDENTIFICATION STICKER (CR4) 1

30 9SG4079 HI-FREQ TRANSFORMER ASBLY 1

31 9SS21132-28 RATING PLATE 1

33 9SL13115 DECAL 1

34 9SS24727-1 DECALCOUNTRY OF ORIGIN 1

Case Back Assembly


Prin

ted

12/0

7/20

15 a

t 15:

16:1

0. P

rodu

ced

by E

nigm

a.

P-897-E.jpg

Case Back Assembly


Prin

ted

12/0

7/20

15 a

t 15:

16:1

0. P

rodu

ced

by E

nigm

a.

KEY PART NUMBER DESCRIPTION QTY1A 9SL11741-1 HORIZONTAL BAFFLE 1


2A 9SL11740 RIGHT UPPER VERTICAL BAFFLE 1


3A 9SL11739 LEFT UPPER VERTICAL BAFFLE 1


4A 9SL11742 LEFT VERTICAL BAFFLE 1


5A 9SL11743 RIGHT VERTICAL BAFFLE 1




9SS10404-134 RESISTORWW50W55% 6

9SCF000045 #10-24X5.00RHS As Req

9ST4479-A INSULATING WASHER 2


9ST9695-1 LOCKWASHER 2

9SCF000010 #10-24HN 1

9SG5657-2 Center Asbly 1

10 9SG3898 BASE ASBLY 1

11A 9SG5702-2 TRANSFORMER & CHOKE WELDED ASBLY 1



28E 9SCF000067 3/8-16HN 2

12A 9SS25387-3 HV TRANSFORMER & TERMINAL ASBLY 1

12B 9ST14539 TRANSFORMER STANDOFF 4


13A 9ST11577-64 CAPACITOR PPMF 15 250 VAC. 10% FLXLD 1

9ST12563-21 LEAD CLAMP 1

9SS8025-111 SELF TAPPING SCREW 1

14 9SL11621-1 RECTIFIER HEATSINK ASBLY 1

9SS9225-17 THREAD FORMING SCREW (ROLLING) 2

9ST11267-A INSULATOR 2

9ST11267-B INSULATOR 2

Center Assembly


Prin

ted

12/0

7/20

15 a

t 15:

16:1

0. P

rodu

ced

by E

nigm

a.

KEY PART NUMBER DESCRIPTION QTY9SM19979 HEAT SINK INSULATION 1

15 9SL11621-2 RECTIFIER HEATSINK ASBLY 1




18A 9SS10404-121 RESISTOR-WW100W 1

9SCF000191 #10-24X7.50RHS 1

9ST4479-A INSULATING WASHER 2



9SCF000010 #10-24HN 1

19A 9ST13359-7 THERMOSTAT 1


19C 9SE106A-13 LOCKWASHER 1

19D 9SCF000005 #6-32HN 1

20A 9SS10404-125 RESISTOR (FIXED WIRE WOUND) 1

20B 9ST11827-59 CARRIAGE BOLT 1

20C 9ST9764-6 INSULATOR 2



9SCF000017 1/4-20HN 1

9SS21170-8 SHUNT & LEAD ASBLY 1

9SCF000028 5/16-18X1.25HHCS 1

9SCF000062 5/16-18X1.00HHCS 1



9SCF000029 5/16-18HN 2

9SS18250-780 PLUG & LEAD ASBLY 1

25A 9SM19983 RECTIFIER SUPPORT BRKT 1

9SS9225-45 THREAD FORMING SCREW 2




26A 9SM19984 RECTIFIER BRKT 1

Center Assembly


Prin

ted

12/0

7/20

15 a

t 15:

16:1

0. P

rodu

ced

by E

nigm

a.

KEY PART NUMBER DESCRIPTION QTY9SS9225-17 THREAD FORMING SCREW (ROLLING) 2



9SL11598-2 RECONNECT PANEL ASBLY 1

28A 9SL11595 RECONNECT PANEL SUPPORT 1

28B 9SM14437-2 RECONNECT PANEL MOLDED ASBLY 1


28D 9SS11012-36 LEAD-FLAT COPPER 1

28E 9SCF000067 3/8-16HN 2



9SCF000040 5/16-18X.75HHCS 6

28J 9SS11604-48 SET SCREW 3

28K 9ST13260-4 DECAL-EARTH GROUND CONN 1

28L 9ST14530-1 RECEPTACLE 2


9SS18922-6 Ground Screw Asbly 2


9SS18922-6 Ground Screw Asbly 2

Center Assembly


Prin

ted

12/0

7/20

15 a

t 15:

16:1

0. P

rodu

ced

by E

nigm

a.

P-897-F.jpg

Center Assembly


Prin

ted

12/0

7/20

15 a

t 15:

16:1

0. P

rodu

ced

by E

nigm

a.

KEY PART NUMBER DESCRIPTION QTY1A 9SG3958 ROOF 1


1C 9ST14882-1 DOOR BUMPER 2

2A 9SL11578 LEFT CASE SIDE 1


3A 9SL11641 RIGHT CASE SIDE WELDED ASBLY 1


4A 9SL11596 TORCH & CABLE HOLSTERMOLDED 1


5A 9SM19783 TORCH PARTS TRAY DOOR ASBLY 1

5B 9ST12584-6 RIVET 2

5C 9SS21033 DOOR LATCH 1

6 9SS12934 COVER SEAL 1

7A 9SM19769 RECONNECT DOOR 1


8A 9SM19955 SPARK GAP DOOR 1


9 9SL8064-1 WARNING DECAL (INTERNATIONAL) 1

11 9SG5692-2 Wiring Diagram 1

12 9SS25247-1 Input Connection Diagram 1

14 9ST13086-172 DECAL-LINCOLN W/ NASCAR (LARGE) 2

16 9SL13115 DECAL 1

20 9SS22127-7 TRI-LINGUAL WARRANTY DECAL 1

Cover Assembly


Prin

ted

12/0

7/20

15 a

t 15:

16:1

0. P

rodu

ced

by E

nigm

a.

P-897-G.jpg

Cover Assembly


Prin

ted

12/0

7/20

15 a

t 15:

16:1

0. P

rodu

ced

by E

nigm

a.

WARNING

AVISO DEPRECAuCION

ATTENTION

WARNuNG

ATENÇÃO

Spanish

French

German

Portuguese

Japanese

Chinese

Korean

Arabic

READ AND UNDERSTAND THE MANUFACTURER’S INSTRUCTION FOR THIS EQUIPMENT AND THE CONSUMABLES TO BEUSED AND FOLLOW YOUR EMPLOYER’S SAFETY PRACTICES.

SE RECOMIENDA LEER Y ENTENDER LAS INSTRUCCIONES DEL FABRICANTE PARA EL USO DE ESTE EQUIPO Y LOSCONSUMIBLES QUE VA A UTILIZAR, SIGA LAS MEDIDAS DE SEGURIDAD DE SU SUPERVISOR.

LISEZ ET COMPRENEZ LES INSTRUCTIONS DU FABRICANT EN CE QUI REGARDE CET EQUIPMENT ET LES PRODUITS AETRE EMPLOYES ET SUIVEZ LES PROCEDURES DE SECURITE DE VOTRE EMPLOYEUR.

LESEN SIE UND BEFOLGEN SIE DIE BETRIEBSANLEITUNG DER ANLAGE UND DEN ELEKTRODENEINSATZ DES HER-STELLERS. DIE UNFALLVERHÜTUNGSVORSCHRIFTEN DES ARBEITGEBERS SIND EBENFALLS ZU BEACHTEN.

l Do not touch electrically live parts orelectrode with skin or wet clothing.

l Insulate yourself from work andground.

l No toque las partes o los electrodosbajo carga con la piel o ropa moja-da.

l Aislese del trabajo y de la tierra.

l Ne laissez ni la peau ni des vête-ments mouillés entrer en contactavec des pièces sous tension.

l Isolez-vous du travail et de la terre.

l Berühren Sie keine stromführendenTeile oder Elektroden mit IhremKörper oder feuchter Kleidung!

l Isolieren Sie sich von denElektroden und dem Erdboden!

l Não toque partes elétricas e elec-trodos com a pele ou roupa molha-da.

l Isole-se da peça e terra.

l Keep flammable materials away.

l Mantenga el material combustiblefuera del área de trabajo.

l Gardez à l’écart de tout matérielinflammable.

l Entfernen Sie brennbarres Material!

l Mantenha inflamáveis bem guarda-dos.

l Wear eye, ear and body protection.

l Protéjase los ojos, los oídos y elcuerpo.

l Protégez vos yeux, vos oreilles etvotre corps.

l Tragen Sie Augen-, Ohren- und Kör-perschutz!

l Use proteção para a vista, ouvido ecorpo.

WARNING

AVISO DEPRECAuCION

ATTENTION

WARNuNG

ATENÇÃO

Spanish

French

German

Portuguese

Japanese

Chinese

Korean

Arabic

LEIA E COMPREENDA AS INSTRUÇÕES DO FABRICANTE PARA ESTE EQUIPAMENTO E AS PARTES DE USO, E SIGA ASPRÁTICAS DE SEGURANÇA DO EMPREGADOR.

l Keep your head out of fumes.l Use ventilation or exhaust to

remove fumes from breathing zone.

l Los humos fuera de la zona de res-piración.

l Mantenga la cabeza fuera de loshumos. Utilice ventilación oaspiración para gases.

l Gardez la tête à l’écart des fumées.l Utilisez un ventilateur ou un aspira-

teur pour ôter les fumées des zonesde travail.

l Vermeiden Sie das Einatmen vonSchweibrauch!

l Sorgen Sie für gute Be- undEntlüftung des Arbeitsplatzes!

l Mantenha seu rosto da fumaça.l Use ventilação e exhaustão para

remover fumo da zona respiratória.

l Turn power off before servicing.

l Desconectar el cable de ali-mentación de poder de la máquinaantes de iniciar cualquier servicio.

l Débranchez le courant avant l’entre-tien.

l Strom vor Wartungsarbeitenabschalten! (Netzstrom völlig öff-nen; Maschine anhalten!)

l Não opere com as tampas removidas.l Desligue a corrente antes de fazer

serviço.l Não toque as partes elétricas nuas.

l Do not operate with panel open orguards off.

l No operar con panel abierto oguardas quitadas.

l N’opérez pas avec les panneauxouverts ou avec les dispositifs deprotection enlevés.

l Anlage nie ohne Schutzgehäuseoder Innenschutzverkleidung inBetrieb setzen!

l Mantenha-se afastado das partesmoventes.

l Não opere com os paineis abertosou guardas removidas.

Customer assistanCe PoliCy

The business of The Lincoln Electric Company is manufacturing andselling high quality welding equipment, consumables, and cuttingequipment. Our challenge is to meet the needs of our customers andto exceed their expectations. On occasion, purchasers may askLincoln Electric for advice or information about their use of ourproducts. We respond to our customers based on the best informationin our possession at that time. Lincoln Electric is not in a position towarrant or guarantee such advice, and assumes no liability, withrespect to such information or advice. We expressly disclaim anywarranty of any kind, including any warranty of fitness for anycustomer’s particular purpose, with respect to such information oradvice. As a matter of practical consideration, we also cannot assumeany responsibility for updating or correcting any such information oradvice once it has been given, nor does the provision of information oradvice create, expand or alter any warranty with respect to the sale ofour products.

Lincoln Electric is a responsive manufacturer, but the selection anduse of specific products sold by Lincoln Electric is solely within thecontrol of, and remains the sole responsibility of the customer. Manyvariables beyond the control of Lincoln Electric affect the resultsobtained in applying these types of fabrication methods and servicerequirements.

Subject to Change – This information is accurate to the best of ourknowledge at the time of printing. Please refer to www.lincolnelectric.com for any updated information.

im10312 precision tig 275 · 2018. 11. 22. · precision tig ®275 register your ... keep your head...

Documents