iglidur bar stock - igus · bar stock iglidur® bar stock ... maintenance-free and predictable...

691

iglidur®

Bar stock

iglidur® Bar stock

Standard range from stock

iglidur® materials as round material

iglidur® J as plate material

Maintenance-free and predictable service life

Fast delivery and low-cost

692

Low friction values in dry running conditions


iglidur®

Bar stock

Machined special parts from iglidur® materials: very fast manufacturing with speedicut. speedicut uses the range of iglidur® bar stock materials, and machines parts to a customer’s design really fast. speedicut uses a 3D model to produce a simple and fast quotation, and parts can then be delivered within days.Select the material, the dimensions and the design. iglidur® for design freedom – as bar stock or as plate material. Ideal for prototypes, test samples and low volumes.

iglidur®-bar stock

iglidur®-Plates

Product range

9 materials Bar stock: Ø 10–100 mmPlate thickness:: 2–25 mmmore dimensions on request

igus® increases constantly the amount of available materials for bar stock. Please check the latest situation online

www.igus.eu/barstock

When to use it? If the required size is not in iglidur® catalog range If you need a bar stock with low wear rates and coefficient of friction

If you need only a small amount of special parts If you need to make a prototype using igus® bearings

When not to use it? If an iglidur® standard catalog bearing is available

If you need an iglidur® plain bearings with special dimensions in high quantity

Please ask us If you need a bar stock without any tribological properties

iglidur® materials as round material


fast delivery and low-cost

–100°

up to max. +250°

–50º

+90º

Temperature (depending on material)

Standard: iglidur® J

More information www.igus.eu/barstock

iglidur® Bar stock | For design freedom

693igus® GmbH Germany | Phone +49 2203 9649-145 Fax -334 | [email protected] | www.igus.eu

iglidur®

Bar stockiglidur® Bar stock | Selection According to Main Criteria

Shaft material:

1 = Cf53

2 = Cf53, hard chromed

3 = Aluminium, hc

4 = Automatic screw steel

5 = HR carbon steel

6 = 304 SS

7 = High grade steel

Load [MPa]0 20 40 60 80 100 120 140 160

iglidur® J

iglidur® W300

iglidur® X

iglidur® J4

iglidur® P210

iglidur® J350

iglidur® A180

iglidur® A350

iglidur® T220

Maximum permissible radial load of iglidur® bearings at

+20 °C +80 °C

Coefficient of Friction [µ]0 0.1 0.2 0.3 0.4 0.5 0.6 Shaft

iglidur® J 5

iglidur® W300 7

iglidur® X 3

iglidur® J4 5

iglidur® P210 6

iglidur® J350 2

iglidur® A180 5

iglidur® A350 6

iglidur® T220 3

Coefficients of friction of iglidur® bearings sliding against steel,

p = 1 MPa, v = 0.3 m/s

Average coefficient of all the seven sliding combinations tested

Coefficient of friction of best combination

Wear [µm/km]0 1 2 3 4 5 Shaft

2

7

4

2

1

7

3

2

3

Wear of iglidur® bearings sliding against steel, p = 1 MPa

Average wear of all the seven sliding

combinations tested

Wear of best combination

Temperature [°C]–100 –50 0 50 100 150 200 250 300

Important temperature limits of iglidur® bearings

Maximum permissible application temperature

Minimum application temperature

694

Bestseller – our most sold iglidur® materials

Lifetime calculation, CAD files and much more support www.igus.eu/barstock

iglidur® Bar stock | Product Rangeiglidur®

Bar stock

prices delivery time

price list onlinewww.igus.eu/barstock

from stock

Material properties table

General properties Unitiglidur®

Jiglidur® W300

iglidur® X

Density g/cm3 1.49 1.24 1.44

Colour yellow yellow black

Max. moisture absorption at +23 °C/50 % r.h. % weight 0.3 1.3 0.1

Max. water absorption % weight 1.3 6.5 0.5

Coefficient of sliding friction. dynamic against steel µ 0.06–0.18 0.08–0.23 0.09–0.27

pv value. max. (dry) MPa · m/s 0.34 0.23 1.32

Mechanical properties

Modulus of elasticity MPa 2,400 3,500 8,100

Tensile strength at +20 °C MPa 73 125 170

Compressive strength MPa 60 61 100

Max. recommended surface pressure (+20 °C) MPa 35 60 150

Shore D hardness 74 77 85

Physical and thermal properties

Max. long term application temperature °C +90 +90 +250

Max. short term application temperature °C +120 +180 +315

Min. application temperature °C –50 –40 –100

Thermal conductivity W/m · K 0.25 0.24 0.6

Coefficient of thermal expansion (at +23 °C) K–1 · 10–5 10 9 5

Electrical properties

Specific volume resistance Ωcm > 1013 > 1013 < 105

Surface resistance Ω > 1012 > 1012 < 103

* length in mm from 100 to 1,000 graduated

in 100 mm steps

Part number Dimensions [mm]

Ø Lengths

iglidur® J – General purpose, good wear-

resistance and low friction

SFRJ-1000 10 100 to 1,000*

SFRJ-2000 20 100 to 1,000*

SFRJ-3000 30 100 to 1,000*

SFRJ-4000 40 100 to 1,000*

SFRJ-5000 50 100 to 1,000*

SFRJ-6000 60 100 to 1,000*

SFRJ-6500 New! 65 100 to 1,000*

SFRJ-8000 80 100 to 1,000*

SFRJ-10000 100 100 to 1,000*


Ø Lengths

iglidur® W300 – Material for high load

requirements

SFRW-3000 30 100 to 1,000*

SFRW-4000 New! 40 100 to 1,000*

SFRW-5000 New! 50 100 to 1,000*

SFRW-6000 60 100 to 1,000*

SFRW-6500 New! 65 100 to 1,000*

SFRW-8000 New! 80 100 to 1,000*

iglidur® X – chemical-resistant high-

temperature material

SFRX-2000 Neu! 20 100 to 1,000*

SFRX-3000 30 100 to 1,000*

Dimensions [mm]


Allrounder – iglidur® materials for many application sectors


Bar stock



from stock



J4iglidur® P210

Density g/cm3 1.48 1.40

Colour grey yellow

Max. moisture absorption at +23 °C/50 % r.h. % weight 0.3 0.3

Max. water absorption % weight 1.3 0.5

Coefficient of sliding friction. dynamic against steel µ 0.06–0.20 0.07–0.19

pv value. max. (dry) MPa · m/s 0.3 0.4


Modulus of elasticity MPa 2,350 2,500

Tensile strength at +20 °C MPa 70 70

Compressive strength MPa 55 50

Max. recommended surface pressure (+20 °C) MPa 35 50

Shore D hardness 74 75


Max. long term application temperature °C +90 +100

Max. short term application temperature °C +120 +160

Min. application temperature °C –50 –40

Thermal conductivity W/m · K 0.25 0.25

Coefficient of thermal expansion (at +23 °C) K–1 · 10–5 10 8


Specific volume resistance Ωcm > 1013 > 1012

Surface resistance Ω > 1012 > 1011


in 100 mm steps


Ø Lengths

iglidur® J4 –

wear resistant and cost-effective

SFRJ4-2000 20 100 to 1,000*

SFRJ4-3000 30 100 to 1,000*

SFRJ4-4000 40 100 to 1,000*

SFRJ4-5000 50 100 to 1,000*

SFRJ4-6000 60 100 to 1,000*

iglidur® P210 – Material for high speeds at

low loads

SFRP210-3000 30 100 to 1,000*

SFRP210-4000 40 100 to 1,000*

SFRP210-5000 50 100 to 1,000*

SFRP210-6000 60 100 to 1,000*

Dimensions [mm]

SFRJ4-2000-500

Length*

Inner-Ø

(00 = solid material)

Outer-Ø

iglidur®-Material

round

iglidur® Bar Stock

Order key

696

For long service life – our most sold iglidur® materials



Bar stock



from stock



J350

Density g/cm3 1.44

Colour yellow

Max. moisture absorption at +23 °C/50 % r.h. % weight 0.3

Max. water absorption % weight 1.6

Coefficient of sliding friction. dynamic against steel µ 0.10–0.20

pv value. max. (dry) MPa · m/s 0.45


Modulus of elasticity MPa 2,000

Tensile strength at +20 °C MPa 55

Compressive strength MPa 60

Max. recommended surface pressure (+20 °C) MPa 60

Shore D hardness 80


Max. long term application temperature °C +180

Max. short term application temperature °C +220

Min. application temperature °C –100

Thermal conductivity W/m · K 0.24

Coefficient of thermal expansion (at +23 °C) K–1 · 10–5 7


Specific volume resistance Ωcm > 1013

Surface resistance Ω > 1010


in 100 mm steps


Ø Lengths

iglidur® J350 –

high-temperature material

SFRJ350-2000 New! 20 100 to 1,000*

SFRJ350-3000 30 100 to 1,000*

SFRJ350-4000 40 100 to 1,000*

SFRJ350-5000 50 100 to 1,000*

SFRJ350-6000 60 100 to 1,000*

Dimensions [mm]

SFRJ350-2000-500

Length*

Inner-Ø

(00 = solid material)

Outer-Ø

iglidur®-Material

round

iglidur® Bar Stock

Order key


Specialists for industrial solutions


Bar stock



from stock

Material properties table Food industry Tobacco

General properties Unitiglidur® A180

iglidur® A350

iglidur® T220

Density g/cm3 1.46 1.42 1.28

Colour white blue white

Max. moisture absorption at +23 °C/50 % r.h. % weight 0.2 0.6 0.3

Max. water absorption % weight 1.3 1.9 0.5

Coefficient of sliding friction. dynamic against steel µ 0.05–0.23 0.10–0.20 0.20–0.32

pv value. max. (dry) MPa · m/s 0.31 0.40 0.28


Modulus of elasticity MPa 2,300 2,000 1,800

Tensile strength at +20 °C MPa 88 110 65

Compressive strength MPa 78 78 55

Max. recommended surface pressure (+20 °C) MPa 28 60 40

Shore D hardness 76 76 76


Max. long term application temperature °C +90 +180 +100

Max. short term application temperature °C +110 +210 +160

Min. application temperature °C –50 –100 –40

Thermal conductivity W/m · K 0.25 0.24 0.24

Coefficient of thermal expansion (at +23 °C) K–1 · 10–5 11 8 11


Specific volume resistance Ωcm > 1012 > 1011 > 1010

Surface resistance Ω > 1011 > 1011 > 1010


in 100 mm steps

Dimensions [mm]


Ø Lengths

iglidur® A180 – General purpose for medical

and food industry (FDA compliant)

SFRA180-1000 10 100 to 1,000*

SFRA180-2000 20 100 to 1,000*

SFRA180-3000 30 100 to 1,000*

SFRA180-4000 40 100 to 1,000*

SFRA180-5000 50 100 to 1,000*

SFRA180-6000 60 100 to 1,000*

SFRA180-8000 80 100 to 1,000*

SFRA180-10000 100 100 to 1,000*


Ø Lengths

iglidur® A350 – High-temperature material for

medical and food industry (FDA compliant)

SFRA350-2000 New! 20 100 to 1,000*

SFRA350-3000 30 100 to 1,000*

SFRA350-4000 40 100 to 1,000*

SFRA350-5000 50 100 to 1,000*

SFRA350-6000 60 100 to 1,000*

iglidur® T220 – Material for tobacco

applications, FDA compliant

SFRT220-3000 30 100 to 1,000*

SFRT220-4000 40 100 to 1,000*

SFRT220-5000 50 100 to 1,000*

SFRT220-6000 60 100 to 1,000*

698

iglidur®-Plates

Lifetime calculation, CAD files and much more support www.igus.eu/iglidur-plates

iglidur® – plates


price list onlinewww.igus.eu/iglidur-plates

from stock

Dimensions [mm]

SFPJ-02-1000-500

Width in mm

Length in mm

Plate thickness

iglidur®-Material

Plate material

iglidur® Bar Stock

Order key

Part number Material thickness Tolerance Dimensions

SFPJ-02-1000-1000 2 +0.000 +0.200 1,000x1,000

SFPJ-02-1000-500 2 +0.000 +0.200 1,000x500

SFPJ-02-500-500 2 +0.000 +0.200 500x500

SFPJ-02-500-240 2 +0.000 +0.200 500x240

SFPJ-04-1000-1000 4 +0.000 +0.250 1,000x1,000

SFPJ-04-1000-500 4 +0.000 +0.250 1,000x500

SFPJ-04-500-500 4 +0.000 +0.250 500x500

SFPJ-04-500-240 4 +0.000 +0.250 500x240

SFPJ-06-1000-1000 6 +0.000 +0.300 1,000x1,000

SFPJ-06-1000-500 6 +0.000 +0.300 1,000x500

SFPJ-06-500-500 6 +0.000 +0.300 500x500

SFPJ-06-500-240 6 +0.000 +0.300 500x240

SFPJ-10-1000-610 10 +0.200 +0.900 1,000x610

SFPJ-10-500-610 10 +0.200 +0.900 500x610

SFPJ-10-500-300 10 +0.200 +0.900 500x300

SFPJ-15-1000-610 15 +0.300 +1.500 1,000x610

SFPJ-15-500-610 15 +0.300 +1.500 500x610

SFPJ-15-500-300 15 +0.300 +1.500 500x300

SFPJ-20-1000-610 20 +0.300 +1.500 1,000x610

SFPJ-20-500-610 20 +0.300 +1.500 500x610

SFPJ-20-500-300 20 +0.300 +1.500 500x300

SFPJ-25-1000-610 25 +0.300 +1.500 1,000x610

SFPJ-25-500-610 25 +0.300 +1.500 500x610

SFPJ-25-500-300 25 +0.300 +1.500 500x300


iglidur®

Bar stockiglidur® Bar stock | Online-Tools

Find & compare semi-finished productsiglidur® materials as semi-finished products for design freedom. This material finder helps you find the right iglidur® material for your project with a few clicks!Select the requirements for the bearing , and then enter the surface pressure and the tem pe ra-ture parameters .The results are displayed below in conjunctionwith your selection .

www.igus.eu/barstock-finder

Calculate lifetime of semi-finished productsQuick calculation of the service life of your iglidur® semi-finished product.In the first step, enter the product details and then enter page for page the details relevant for your application of the iglidur® material . Instantly you will be given the service life of your product under the operating conditions you have specified.The results are displayed as service life in hours .

www.igus.eu/barstock-expert

Configure required dimensionsQuickly configure your required bearing and determine its price.Select the desired bearing type and then enter the dimensions and the material selection of the bearing, then select the tolerance of the mounting hole .Enter the quantity and you immediately see the price online . If the “on request” is shown, please enter your personal details and send us a request. We will contact you shortly.

700

iglidur®

Bar stock


My Sketches

701

speedigus

speedigus – customised special parts

save costs

technical benifits for products and machines

Maintenance-free igus® tribo-plastics

fast delivery and cost-effective

702

speedigus

More support www.igus.eu/speedigus

speedigus | customised special parts

What is speedigus? At igus, we have the aim of helping our customers reduce costs while bringing technical benefits to their products and Machines. We call this ”plastics for longer life.” Sometimes our customers require custom parts or services, and for many years this has been an important part of the igus® support. Now, with speedigus, we combine custom parts with speed, Using the benefits of igus® tribo-plastics.

Customised speedigus parts can be made in three ways:

speedimold

Custom iglidur® parts manufactured

by injection moulding.

speedimold This is where a 3D model from the customer is used to produce a fast aluminum injection mould tool, allowing real igus® parts to be manufactured very quickly. The leadtime for this service varies from 24 hours to a maxi-mum of three weeks.

speedicut

Custom iglidur® parts machined from

bar stock.

speedicut This is where the igus® bar stock is used to machine a custom part to a 2D drawing or 3D model. The leadtime for this service Varies from 3 days to a maximum of three weeks.

speedifit

iglidur® parts fitted into a custom

assembly.

speedifit This is where an igus® part is fitted into a custom housing or unit, and the whole assembly is supplied as one part. The leadtime for this service varies from Five days to three weeks.

Our promise for all speedigus-options: On-time delivery and response to all inquiries within 24 hours.

delivery time1–15 days




speedigusspeedigus | customised special parts

How does speedigus work?

1 You tell us about your desired special design: what kind of material, special requirements, etc., And send us your 3D model via email

2 You get a quote; pay attention to your lead time and send us your order

3 The tool for your individual speedigus part is produced or the speedifit- and speedicut-parts will produce directly in our manufacturing and assembly centre

4 The required speedimold-parts are injection molded from your chosen iglidur® material (only speedimold service)

5 Now you can install and use your parts.

iglidur bar stock - igus · bar stock iglidur® bar stock ... maintenance-free and predictable...

Documents