The illustrations in the brochure may show extras subject to additional cost.

IBAK Inspection and Rehabilitation Systems in Modular Design

– 2 – – 3 –

Right from the beginning, IBAK Inspection Systems were a modular concept: the cam-era heads are suitable for both camera trac-tors and push rod systems, the camera trac-tors and camera systems can be operated for the most part with all cable winches and control systems.In response to the ever-increasing speed of technological change and the higher technological demands on camera resolu-tion and image quality, new products have been continuously developed at IBAK over the last few years: from small push rod sys-tems through manhole inspection cameras to vehicle-based systems with Full HD or Ultra HD components. In addition, the port-folio of cutting robots has been constantly enhanced and integrated into the IBAK TV inspection range. The complete IBAK product range is under permanent review and is modernised in line

with the market requirements. To further develop a clearly structured modularity with future potential, some products of the IBAK portfolio have been re-engineered and sev-eral new products have been added.The result is a system of modular compo-nents that can be flexibly combined with each other and extended with further func-tions and units at any time. Depending on the field of application, the IBAK analog cameras can be operated with

Modularity with a Building Block Approach

the push rod systems MicroLite and Mini-Lite, the three control consoles BP1, BP2 and BP100, a camera tractor and the cable winches KW206/306. The new operating system BS10 is designed for optimum outfitting of the operator's sec-tion in the vehicle. It consists of a control console (BP10) and a BS10 interface box. In combination with an efficient PC and the inspection software, this forms an effec-tively deployable system.

MicroLitewith a BP1 and an AxialCam

MiniLitewith a BP2 anda NANO L

MainLitefit with a BP100,a KW206, a T66 and an ORION

MainLite solidwith a boom and 200/300 m of cable for vehicle installation

NanoGatorwith a BP100

ASPECTAwith a BP2

– 5 –– 4 –

BP1

BP2

BP100

MiniLite ASPECTA MainLite fit

KW206/306

NanoGatorMicroLite

Combination Possibilities of the Portable Components

– 6 – – 7 –

Control Consoles

Control Console BP1 BP2 BP100Width x height x depth 270 x 190 x 40 mm 337x190x40 mm 405x190x40 mmWeight approx. 2.6 kg approx. 2.8 kg approx. 3.0 kg

Connections 2x USB 3.02x USB 3.0 1x HDMI

2x USB 3.0 1x HDMI 1x USB 2.0

Data storage Text input or storage of photo or video files (MPEG 4 AVC/H.264) on the integrated PC, data exchange via USB 3.0

Monitor Splashproof (IP43), 10 inch touch display, with BP2 and BP100 an external monitor can be connected via HDMI

Battery charge level indicator yes yes yesBattery changing indicator yes yes yesLength measurement/indi-cator

yes yes yes

Combinable withIBAK Cameras AxialCam AxialCam AxialCam

NANO, NANO L NANO, NANO LPOLARIS POLARIS ORION, ORION L ORION, ORION LASPECTA ASPECTA

ORPHEUS 2/3ORPHEUS Lite

IBAK Push Rod Systems MicroLite MicroLite MicroLite MiniLite 2 MiniLite 2

IBAK Camera Tractors T66, T76IBAK Cutters NanoGatorIBAK Cable Winches KW 206, KW 306

IBAK Software

IKAS recorder (standard), IKAS mini, IKAS evolution (depend-ing on the configuration of the terminal equipment, software licences are possible for IKAS evolution Push, IKAS evolution Starter and IKAS evolution Professional)

Power Pack 18VDC 4 Ah (Li-Ion), 2x (not included in the scope of supply)

The three control console models (BP1, BP2, BP100) are equipped with a 10 inch touch display. These are used to operate the software and to control the IBAK cameras und camera tractors as required. The BP dis-plays are protected by a bonded glass plate so that they cannot get scratched and are also well shielded from rain.All three control consoles are equipped with efficient PCs so that complete IBAK sewer analysis software can be installed and used with the full range of functions. The BP1 is optimised for operation of the MicroLite with the axial camera type Axial-Cam. The BP2 is additionally equipped with a joy-stick and is the ideal choice for the opera-tion of pan and rotate cameras. The control console BP100 offers the wid-est range of functions. It is equipped with two joysticks with which both the cameras and the camera tractors can be operated. For this purpose, the BP100 can either be directly connected to the compact sys-tem to be operated or installed in the vehi-cle with a vehicle extension (consisting of an emergency stop switch for the BP100

and a table mount). The IBAK lateral cutter NanoGator is also operated from a BP100 equipped among others with an emergency stop switch for cutting operations. For all BP models, there is a great selec-tion of accessories including ergonomic handrests, display extenders and extension cables.

BP100 for the Lateral Cutter NanoGator with ergonomic handrests

– 8 – – 9 –

Functions

Project management – ✓ ✓Sewer database – ✓ ✓Video recording ✓ ✓ ✓Video overlay (from hotkey and text input) ✓ ✓ ✓Video overlay from sewer database – ✓ ✓Still photos ✓ ✓ ✓Condition codes acc. to standards (EN13508,WRc) – ✓ ✓Sewer data interface – – ✓Data Transfer

Video and photo files ✓ ✓ ✓Inspection Video Player with data index and PDF reports – ✓ ✓Complete sewer data view-only program (reports, films, photos, MAP/GIS) – – ✓Options

Determination of DN ✓ ✓ ✓Measurements – – ✓MAP (GIS) – – ✓Further IKAS evo options – – ✓

Software Variantsfor BP1, BP2, BP100

Create Projects and Generate Reports

IKAS recorder software is installed on all control consoles. With this basic software, vid-eos and photos can be captured, saved and transferred.

With IKAS mini, inspections of sewer systems can be captured according to the EN 13508-2 standard valid in Europe.

Input of defects in sewer sections and manholes, photo and video recordings are easy to enter and save through intuitive menu guidance.

The inspection results are documented in clearly arranged reports and saved in PDF format. Otherwise, with a USB stick, the data can also be simply passed on to the cus-tomer. Thus, the defects data are clearly presented and can be viewed together with the corresponding photos and videos. This makes all defects in sewers recognisable and comprehensible.

IKAS mini gives the inspector flexibility during inspections without tying him down to fixed sets of rules. When in addition inspections are to be performed according to com-munal rule sets or specific data exchange formats (such as DWA-M 150), an upgrade to the professional IKAS evolution can be purchased at any time.

IKAS evolution offers the possibility of purchasing specific licences for any application purpose. On the following pages you will find a rough overview of the possibilities of-fered by IKAS evolution licences.

– 10 – – 11 –

IKAS

System Push Starter Professional

Push rod and Manhole operation

MicroLite ✓ ✓ ✓ ✓ ✓

MiniLite ✓ ✓ ✓ ✓ ✓

ASPECTA ✓ ✓ ✓ ✓ ✓

NanoGator ✓ ✓ ✓ ✓ ✓

Mobile systems for camera tractor operation

KW206/306 (MainLite fit) + BP100 ✓ ✓ – ✓ ✓

Vehicle installation in camera tractor operation

KW206/306 (MainLite solid) + PC ✓ ✓ – – ✓

Depending on the configuration of the terminal units, different IKAS evolution software licences are possible: IKAS evolution Push, IKAS evolution Starter and IKAS evolution Professional.

Software LicencesDongle/Identification of Units

– 12 – – 13 –

MicroLiteCompact push rod camera system

The IBAK MicroLite is a compact push rod camera system for the inspection of house and estate drainage systems. It features simple operation via one of the control consoles BP1, BP2 or BP100. These are equipped with a 10 inch touch display (BP1) and optionally also with one (BP2) or two joy-sticks (BP100). After a short training period, the systems can be reliably operated through intuitive menu guidance. Text can be input or photo and video files (MPEG 4 AVC/H.264) can be saved on the integrated PC with IKAS recorder. Data is exchanged via a USB stick. With its weight of approx. 16.5 kilogrammes, the MicroLite is a favourably priced compact starter system. This small coiler for push rod operation is available in two different versions: the MicroLite with a BP1 and 30 metres of push rod with a permanently mounted axial camera type AxialCam. This version permits inspections to be performed in DN 50 upwards and is eminently suitable if the section to be inspected requires a particularly bend-capable push rod.The second model is a MicroLite with a BP2 and 40 metres of even more bend-capable push rod with a plug-in AxialCam or the small pan and rotate camera NANO. With this system, lateral inspections are possible in DN 80 pipes upwards.

The control consoles of both versions are equipped with IKAS recorder basic software with which videos and still photos can be captured. Depending on the requirements regarding inspections and the transfer of inspection data, software types IKAS mini or IKAS evolution can be installed optionally.

MicroLite with a permanently- mounted axial camera

with exchangeable camera

Range of application from DN 50 upwards from DN 80 upwardsMagic Push Rod 30 m, ø 12mm –Perfect Push Rod – 40 m PP20, ø 8.6 mmWidth x height x depth 350 x 570 x 470 mm (without control console)

Weight of the coilerapprox. 16.5 kg, incl. the coiler drum, the push rod and the camera

approx. 16.5 kg, incl. the coiler drum, the push rod and the camera

Data storage Text input or storage of photo or video files (MPEG 4 AVC/H.264) on the integrated PC, data exchange via USB 3.0Length measurement/indicator

yes yes

Power Pack 18VDC 4 Ah (Li-Ion), 2 x* 18VDC 4 Ah (Li-Ion), 2 x*

Combinable withIBAK Cameras AxialCam

(permanently mounted)AxialCam (plug-in model), NANO, NANO L

Control Console for BP1, BP2, BP100 BP1**, BP2, BP100

Above: MicroLite with a BP1 and an integrated (not plug-in type) AxialCam

The AxialCam, the NANO and the NANO L can be connected to the MicroLite with the 40 metre coiler drum.

The MicroLite version with the camera exchanging option is operated with BP1**, BP2 or BP100.

* not included in the scope of supply** only recommended with AxialCam

– 14 – – 15 –

System Technical Data – MiniLiteProduct classification Compact push rod camera system

Perfect Push Rod80 m (exchange drum 500/10), optionally other exchange drums (see accessories)

Width x height x depth 400 x 780 x 720 mm (without the control console)

Control console dimensions W x H x D: 337 x 190 x 40 mm

Monitor Splashproof, IP 43, 10 inch touch display

Weight of the control console approx. 2.8 kg

Weight of the coiler approx. 29.5 kg (with the exchange drum)

Data storageText input or storage of photo or video files (MPEG 4 AVC/H.264) on the integrated PC, data exchange via USB 3.0

Length measurement/indicator yesPower Pack 18VDC 4 Ah (Li-Ion), 2 x*

Combinable withIBAK Cameras AxialCam, NANO, NANO L, POLARIS, ORION, ORION LIBAK Extension Kit yes, optional

Accessories

Exchange drum, Magic Push Rod

500/12 with AxialCam and 30 m of push rod, operation in DN 50 upwards500/15 with 40 m of push rod, operation in DN 80 upwards

Exchange drum, Perfect Push Rod

500/10 with 80 m of push rod, operation in DN 80 upwards

Software IKAS mini, IKAS recorderExternal counter yes, required with 3D-GeoSense

MiniLiteCompact push rod camera system

Like the MicroLite, the IBAK MiniLite is a compact push rod camera system for the inspection of hose and estate drainage sys-tems. Whereas the MicroLite is an ideal, easy-to-handle starter model for simple lat-eral inspections, the MiniLite was designed to cover an as wide as possible range of applications thanks to its modular extendibil-ity and numerous accessories.

The MiniLite has an exchangeable coiler drum. With the 80 m push rod version, the cameras are of plug-in type; compatible are all current IBAK push rod cameras. In com-bination with the ORION, the NANO or the POLARIS optional diameter measure-ments can be performed. Depending on the

requirements, the system can be additionally equipped with an extension kit and software. IKAS recorder software is available for sim-ple projects without any complicated data exchange formats. If you want to perform inspections of sewer systems according to the EN 13508-2 standard valid in Europe, IKAS mini can be installed and the inspec-tion results can be printed out in the form of clearly arranged reports or output in PDF format.

If specific data exchange formats are required, or if a 3D site plan is to be drawn up after a 3D-GeoSense pipe run measurement, the use of complete IKAS evolution software is recommended.

DN 80 upwards with exchangeable cameras*

* DN 50 upwards with permanently mounted cameras

* not included in the scope of supplyThe MiniLite is standardly supplied with an exchange drum 500/10 with 80 metres of Perfect Push Rod. This features outstanding rigidity and a long range. However, depending on the area of operation, exchange drums with a Magic Push Rod are also available for the MiniLite. This is shorter and more flexible than the Perfect Push Rod and is an alternative particularly in combination with a plug-in or permanently mounted AxialCam, if a specially bend-capable solution is required for ramified pipe runs. Magic Push Rods and Perfect Push Rods are also available with a 512-Hz locator transmitter or can be refitted with one.

– 16 – – 17 –

MiniLite AccessoriesPossible Configurations Simple

Installation

IKAS-evolution-3D-Geo-Sense, pipe run data

Ergonomic handrests for BP1, BP2, BP100

The voice signal is transmitted via a Bluetooth headset to the MiniLite and from there by a cable to the inspection vehicle.

Accessories for Greater Con-venienceErgonomic handrests are available for the control consoles. They can be ordered as accessories and are easy to install. To increase the stability when winding on the push rod, in particular on uneven or wet ground, there is an additional base, also for buyer installation.

Extension Kit To inspect hard-to-access sewer sections and laterals from the vehicle, the MiniLite can be connected to big systems with an extension kit. In this case, the report soft-ware and the capture hardware in the vehi-cle can also be used for push rod operation. The video signal and the length counter data are transmitted by the camera cable. The operator in the vehicle communicates with the operator at the push rod system via an intercom system.

IKAS evolution 3D GeoSense

In combination with a 3D-GeoSense soft-ware module, an additional counter and a camera equipped with a 3D sensor and the DEIMOS camera guide device, 3D sensor pipe run measurements can be performed with the MiniLite. The measurement is per-formed in a single operation together with the TV inspection. The measured pipe run is shown in real time during the inspection and is saved with x,y,z coordinates according to the reference coordinate system. The IKAS evolution MAP Route Assistant is addition-ally required for this. Depending on the IKAS evolution sewer interface used, the result-ing site plan can be exported in all supported sewer data formats. Adaptation to precisely defined position coordinates, commonly termed geo-fixed points, can be performed with the assistant functions of the software.

MiniLite with an additional counter

ORION L 3D with the DEIMOS camera guide device: this guides the camera parallel to the pipe axis of the surveyed pipe during the pipe run measurement.

MiniLite operating as an extension system

Additional base for the MiniLite

– 18 – – 19 –

MainLiteThe Professional, Flexible System for Mainline Inspection

The flexible and compact camera trac-tor system MainLite is available both as a model for vehicle installation (MainLite solid) or as a portable system (MainLite fit).

MainLite fitThe portable solution with up to 300 m of cableMost analogue IBAK cameras and the cam-era tractors T66 and T76 can be connected to the system. For small pipe diameters from DN 100 upwards, for example a T66 can be operated with the ORION camera, for bigger pipes from DN150 upwards, a T76 camera tractor can be operated with an ORPHEUS. MainLite fit consists of the versatile con-trol console BP100 with a 10 inch touch dis-play and two joysticks to operate the cam-era and the camera tractor. The motor-driven winches with 200 metres (KW206) or 300 metres of camera cable (KW 306) can be transported with the mobile rack to locations which are difficult to access with vehicles. With the integrated seat, you can work com-fortably even outside an inspection vehicle.

MainLite solidThe solution for vehicle installation with up to 300 m of cableMainLite solid is identical to the MainLite-fit system, except that it is a version for vehi-cle installation. As with the MainLite-fit sys-tem, the customer can also use the control unit BP100 in the vehicle or choose a model with an integrated PC, keyboard and control console with joysticks (BP10). The inspec-tion vehicle can be operated optionally with the 200 metre (KW206) or the 300 metre cable winch (KW306). The MainLite fit and MainLite solid systems can be equipped both with IKAS mini and IKAS evolution.

Full HD and PANORAMO The customary systems are still available.

If you want to make Full HD or PANORAMO recordings, use a MiniLite 2 as an extension system or perform a satellite inspection in LISY operation, the customary control sys-tems BS 3.5, BS7 and BS5 and the winches KW305, KW310 and KW505 are still availa-ble. (Full HD only in combination with BS7, BS5; PANORAMO only in combination with KW505).

Fig. similar

MainLite fit- KW206- BP100- T76- ORPHEUS

Lite

MainLite solid- KW206/306- BP100- T66- ORION

– 20 – – 21 –

With its weight of 40 kg, the system can also be easily transported to hard-to-access locations. In addition, the coiler and the con-trol console can be flexibly arranged so that ergonomic working procedures are possible at all times.As an electric motor is used, a power outlet is all that is required to operate the NanoGa-tor. No power-consuming, noisy generators and compressors are necessary.

NanoGatorEfficient in Laterals For DN 100

upwards- portable- direction-changing

function- 90° bend-capable

With the NanoGator, IBAK has a lateral cutter in the product range which is particu-larly suitable for small diameters (from DN 100 upwards) and complex lateral networks. With its spherical form, the actively steera-ble cutter arm and the easy-slide yet robust push rod (40 metres), the NanoGator is the ideal choice for complex lateral networks with small diameters. The brushless elec-tric motor used in the NanoGator is power-ful and very long-life. The water-cooled cutter cuts gently into the material at a speed of up to 20,000 r.p.m. and requires no clamping device. The diamond-coated cutter tool cuts almost any material and was designed by IBAK exclusively for the NanoGator. The inno-vative cutter head is equipped with a pat-ented bearing which is uncoupled from the motor shaft. For the user, this means that the bearing is changed each time the tool is exchanged so that the shaft and the motor are very durable and you always work with a new, unworn bearing. Furthermore, as the bearing is integrated into the tool, it

was possible to implement a compact and space-saving design which, in combination with the high performance, is unique on the market. The cutter tool is simple to exchange (even at the site of operations) with a quick exchange tool specially designed for the NanoGator.The two integrated cameras supply images from two different perspectives so that you have an optimum view of the site of the cut-ting operations. The cameras are cleaned with water to avoid any impairment of the visibility from grinding dust etc. The NanoGator system is both efficient and user-friendly. The cutter motor can be started and stopped with a foot switch so that you do not have to let go of the push rod and the joystick. Even in the smallest dimen-sions with 90° bends the NanoGator can be easily retracted thanks to its shape and the installed friction clutch: in snake mode, the cutter arm moves back and forth like a snake, thus actively facilitating retraction of the NanoGator. With control console BP100, the cutter is easy to operate and videos and

photos can be captured with data overlay. The data is easily exchanged via a USB port. The BP100 is equipped with an integrated PC so that further software such as IKAS Gator can be installed without any problem. This ensures perfect data communication. Low operating costs, low noise emissions and a high degree of efficiency make the NanoGator an optimum system for cutting in laterals.

Distilled water (approx. 1l/h)

– 22 – – 23 –

AQUA DEST.

NanoGator coiler with a cutter head and a BP100

40m of easy-slide push rod NanoGator cutter head

Control console BP 100 with extension for the NanoGator

n Emergency switchn On/Off-switchn Connection for foot switchn Processing of 2nd videon Connection between

coiler and BP

90-260V AC (DC operation possible)1500W

NanoGatorMobile System Concept

– 24 – – 25 –

Video images from the two cameras of the NanoGator cut-ter head (camera 1 and 2, see the fig. below) during cutting operations

Camera 1

Camera 2

System Technical Data – NanoGatorRange of application Laterals

Pipe dimensionsDN 100 (relined) to DN 150, to DN 200 with cam-era guide device, 90° bend-capable in DN 100

NanoGator HeadDiameter 80 mmLength of interfering contour without arm 80 mmLength with arm 190 mmWeight 1500g

Output Mechanical power in continuous operation with 40m of push rod: 340W

Speed 20,000 r.p.m.Tilt angle +/-110°, integrated friction clutch for tilt driveRotation angle 300°Lighting 4x LEDTwo integrated cameras Resolution 2x 480x6400 pixels = 960x640 pixelsFocus Fixed focusComplete System with CoilerWeight of complete system 40 kg with BP and a full water tankDimensions 800x750x300mmStandard cable length 40mWater consumption 1 l/h distilled water during cutting operationsVolume of integrated water tank 1.5 lWater consumption for camera cleaning approx. 20 ml per cleaning operation

Dust protectionGrinding dust is bound permanently by cooling water

Pressure monitoring yesPower supply 90-264 VAC 1.5kWOperation BP100Operating temperature 0°C to 40°CStorage temperature -10°C to 50°C with empty cooling system Locating transmitter NoExplosion protection No

Camera 2 Camera 1 Camera 2 Camera 1

Camera 2 Camera 1Camera 2 Camera 1

– 26 – – 27 –

ASPECTAA Quick Look into the Sewer

Sewer MirrorASPECTA

The ASPECTA is a manhole zoom camera – also known as an electronic sewer mir-ror. With this camera, you can have a look into associated sewers from the manhole without having to enter it. The ASPECTA is used to check the operational status and can be utilised for instance to plan needs-based sewer cleaning and additional inspec-tion operations. Thus, it is a simple, rapid and cost-effective instrument for scheduling further measures. Thanks to the high zoom factor (30 x optical) and the lighting which is adequate even in large diameter sewers, a view is also possible up to 30 metres into parts of sewer sections a long way from the manhole. With the laser integrated into the current model, the distance to particu-lar points can be measured over the entire length of 30 metres. The camera is placed in the manhole with the aid of a telescopic rod and positioned in front of the sewer. A mounted base to place the camera in the

invert and a motor driven pan mechanism make for easier, precise handling. The stand-ard rechargeable battery used is an uncom-plicated method of power supply as batter-ies can be easily obtained or recharged.

The ASPECTA is operated optionally with control console BP2 or BP100, both of which can also be used with the other portable IBAK systems.

Ideally, IKAS Cleaner cleaning software is used for operating the ASPECTA because with this the captured job data regarding the degree of soiling and the cleaning oper-ations performed in the sewer section can be directly transferred digitally to the sewer data manager software. This data can be supplemented with the ASPECTA image information so that paper-free data com-munication is maintained between e.g. the cleaning vehicle and the information system.

– 28 – – 29 –

System Technical Data – ASPECTAProduct classification Electronic sewer mirrorCameraType of camera Tilt head cameraRange of application DN 150 – DN 1200Dimensions Ø 123 mm, length 136 mmWeight (system/ camera) approx. 11 kg/ approx. 1.5 kgZoom 30 x optical, 10 x digitalF (shutter) 1.6-4.7f (focal length) 4.3 mm – 129 mmLighting 12 white power LEDs, reflectors, angle of radiation 15°protection class IP 68Permitted ambient temperature -10°C to +50°C in operation, -20°C to +60°C for storageTest pressure for leak-tightness noPressure monitoring noShutter function Manual, automatic, remote controlledPanning range Bottom 90°, top 60°Aperture angle Wide angle 71°, tele 2.5°Focus function/range Manual 10 cm – ∞, remote controlled, autofocusSensor (inches) 1/3“ CMOSTV standard NTSC or PALHorizontal image resolution 700 linesImage stabiliser yesIntegrated laser yesExplosion protection no

Telescopic rodMaterial GFRP/CFRP (black)Locking device Quick clampVersion 1Length (standard), 5-piece 1.90 m – 8.15 mWeight 2.4 kgDiameter of handpiece/tip 40 mm / 21mmVersion 2Length (optionally 10 m), 6-piece 1.95 m – 10.0 mWeight 2.6 kgDiameter of handpiece/tip 40 mm / 17 mm

Power supplyRechargeable battery 18 VDC, 4 Ah (Li-ion), 1 xBattery operating time approx. 2 hours

Charging time 36 minutesCharger operating voltage 230 VOperation/Data TransferControl Console BP2, BP100Dimensions W x H x D: 337 x 190 x 40 mm, 405 x 190 x 40 mmWeight approx. 2.8 kg, ca. 3 kgMonitor Splashproof (IP43), 10 inch touch displayJoystick functions Zoom, tilt, manual focusPermitted ambient temperature 0°C to +35°C in operation, -10°C to +40°C for storage

SoftwareIKAS recorder (standard), IKAS Cleaner (with IKAS record-er extension), IKAS mini and IKAS evolution (optionally for parallel use with the MiniLite 2)

Data captureText input or storage of photo or video files (MPEG 4 AVC/H.264) on the integrated PC, data exchange via USB 3.0

AccessoriesBipod Aluminium, adjustable 109 cm – 180 cm, weight 1.95 kgManhole grid Work grid Ø 670 mm with opening, weight 5.6 kgBox for the camera, the control console and other accessories

– 30 – – 31 –

IBAK BS10System Technical Data – BP10/Interface BoxProduct classification Control system for vehicle installation

Intercom systemInterior loudspeaker, exterior loudspeaker, interior micro-phone

Camera cable length depending on the winchVideo processing PC with inspection software requiredVideo in/out CVBS and Y/C for the PCKeyboard for connection to the PCTV standard PAL or NTSCOperating voltage 48V, is supplied by the corresponding winchInterfaces to the PC Serial port, USBSafety device Emergency stop

Combinable withIBAK Cameras NANO, ORION, ORPHEUS 2/3, ORPHEUS LiteIBAK Winches KW206, KW306IBAK Camera Tractors T66, T76

The IBAK BS10 is control system for IBAK inspection systems for installation in an inspec-tion vehicle. This central control and operating unit consists of a control console (BP 10), a BS10 interface box and a keyboard. All winches of the new generation (KW206/306) and the compatible camera tractors and cameras can be operated with this. The connected components are identified automati-cally by the system. Operation of the camera tractor and the camera is user-friendly with configurable joysticks. The individually assignable keys of the control console offer the user numerous additional presetting possibilities. In addition, various features such as the light intensity, functions of the camera and the camera tractor and other system-relevant options can be controlled.With the integrated data display unit, descriptions of defects, symbols or comments can be overlaid on the video image via the keyboard.Furthermore, video capture hardware can be connected. The intercom system can be used for communication via the microphone integrated into the control console.

1904

15_K

ompa

ktan

lage

n_E

N

BP1

BP2

BP100

MiniLite

NanoGator

MainLite fit

KW206

ASPECTAMicroLite

IBAK Helmut Hunger GmbH & Co. KG Wehdenweg 122 · 24148 Kiel · Germany Tel. +49 (0) 431 7270-0

Coming soon:

MainLite easy