i series ip6-1152/66 - full compass systems€¦ · i series ip6-1152/66medium power 15-inch...
TRANSCRIPT
TECHNICAL SPECIFICATIONS1 Operating Mode Passive or Biamp with DSP
Operating Environment Indoor or Weather-Resistant Outdoor
Operating Range2 32 Hz to 19 kHz
Nominal Beamwidth (H x V) 60° x 60°, rotatable waveguide
TransducersLF 1 x 15" (381mm) ferrite driver, 3" (76mm) voice coilHF 1 x 1.4" (36mm) exit, 3" (76mm) voice coil, hybrid titanium/polyimide
diaphragm, ferrite compression driver
Continuous Power Handling3 @ Nominal Impedance
Passive* LF HF
69V 63V 24V
600W @ 8 ohms (2400W peak)500W @ 8 ohms (2000W peak)75W @ 8 ohms (300W peak)
Nominal Sensitivity4 Passive LF HF
@ 1W 96 dB 96 dB 107 dB
@ 2.83V 96 dB 96 dB 107 dB
Nominal Maximum SPL5
(Whole Space)Passive LF HF
Peak130 dB 129 dB132 dB
Continuous124 dB 123 dB 126 dB
Equalized Sensitivity6 System @ 1W
94 dB @ 2.83V94 dB
Equalized Maximum SPL7 System Peak
128 dBContinuous 122 dB
Recommended AmplifiersPassive LF HF
600W - 1200W @ 8 ohms, (69V - 98V)500W - 1000W @ 8 ohms, (63V - 89V)75W - 150W @ 8 ohms (24V - 35V)
PHYSICAL
Input Connection Indoor: (2) Screw terminal blocks (6-position)Outdoor: Sealed Gland Nut with 12ft (3.6m) 14 Ga. SJOW cable
Mounting Points (15) M10 threaded rigging points
Environmental Outdoor: IP55W per IEC 60529 , MIL-STD-810G
Weight 79 lbs (35.8 kg) loudspeaker only
Dimensions H x W x D 30.80" x 16.50" x 20.07" (782 x 419 x 510 mm)
Finish Refer to the Technical Drawing
OPTIONS
Accessories(Refer to BalancePoint™ Flyware Accessory Guide for complete listing)
Rigging kits include: BFR22: BalancePoint™ Fly Rails; IUB1152: U-Bracket; IVY1152: Vertical Yoke; IAF40/IAF55: Isometric Array Frames; HAB-BFR38: Sub/Dual 2-Way Horiz Array; HSB/VSB: Multiple Splay Brackets for Horiz/Vert Arrays with/without Sub Behind options; DFS: Downfill Splay Kit; DVS-BFR22: Dual Vert Splay Kit with BalancePoint™ Fly Rails; TPK: Tight Pack Kit; IUB1152WRG: Reinforced 304SS U-Bracket (Grey)
Configure-to-Order (CTO) Custom color; Custom cable lengths on outdoor version
I SERIESPoint Source 600
IP6-1152/66MEDIUM POWER 15-INCH TWO-WAY 60° x 60° INSTALLATION LOUDSPEAKER
Community strives to improve its products on a continual basis. Specifications are therefore subject to change without notice.
*Rated continuous maximum input voltage at passive loudspeaker input may be higher than for directly connected transducers due to losses in the passive crossover. Voltages applied to the transducer terminals through the passive crossover shall always be the same or lower than the rated continuous voltage for each device.
30.80" (782mm)
FEATURES• Long excursion ferrite LF driver with FEA-optimized motor and symmetric movement suspension
• 3-inch voice coil, 1.4” exit HF driver; hybrid titanium/polyimide diaphragm on low compression phase plug
• Lightweight and compact with deep LF extension
• Large rotatable waveguide with individually voiced crossover, single amp / biamp selectable
• Innovative low profile modular bracket systems create elegant arrays with simplified installation
APPLICATIONS MAIN PA (Small to Medium Size Venues)
Houses of Worship · Auditoriums · Restaurants Meeting Rooms · Theaters · Corporate A/V Systems
DISTRIBUTED OR FILL (Larger Size Venues)Arenas · Stadiums · Night Clubs · Theaters Themed Entertainment · Larger Houses of Worship
DESCRIPTIONI SERIES Point Source 600 loudspeakers provide excellent acoustic performance, modular flexibility and elegant aesthetics for modern performance venues. Designed to support the goals of systems integrators and consultants both acoustically and mechanically, I SERIES includes a wide variety of arrayable, rotatable coverage patterns and a comprehensive selection of modular bracket systems that accelerate system design and system commissioning.
FEA-optimized ferrite motors, mechanically mirrored suspension and advanced cooling system combine to provide linear performance with minimal power compression. The custom long-excursion LF driver delivers deep bass response and a detailed midrange at maximum SPL levels. The HF driver delivers excellent sound quality from a hybrid diaphragm of deep drawn titanium and resonance-absorbing polyimide, coupled to a patented low compression, low resonance phase plug for very low distortion performance with abundant headroom.
The rotatable 13-inch (330mm) HF waveguide provides well-defined coverage and a smooth off-axis response that enhances arrayability. Individually voiced crossovers produce proper beamwidth matching transitions and identical sonic signatures, permitting horn patterns to be mixed throughout an installation. Additionally, user selectable single-amp or biamp operating modes expand application flexibility.
I SERIES
IP6-1152/66 MEDIUM POWER 15-INCH TWO-WAY 60° x 60° INSTALLATION LOUDSPEAKER
Point Source 600
1
10
100
10 100 1000 10000
Impedance LF Frequency Response Frequency Response
Frequency (Hz)100 1000 1000020
Minimum Impedance: (Passive) 7.5 ohms @ 140 Hz, (LF) 7.9 ohms @ 250 Hz, (HF) 7.9 ohms @ 4500 Hz
IMPEDANCE (Ohms)
1
10
100
10
100
10 100 1000 10000
Beamwidth (Degrees)BeamH BeamV Horizontal Vertical
Frequency (Hz)100 1000 1000020
70
80
90
100
110
10 100 1000 10000
Off-Axis Vertical (down)Half Space Mag [dB] (0°) Mag [dB] (10°)Mag [dB] (20°) Mag [dB] (30°) Mag [dB] (40°)
100 1000 1000020Frequency (Hz)
100 1000 1000020
Frequency (Hz)
70
80
90
100
110
10 100 1000 10000
Am
pli
tud
e (
dB
SP
L)
Frequency (Hz)
Off-Axis HorizontalHalf Mag [dB] (0°) Mag [dB] (10°)Mag [dB] (20°) Mag [dB] (30°) Mag [dB] (40°)
Frequency (Hz)100 1000 1000020
Half-space 0° 10° 20° 30° 40°
70
80
90
100
110
10 100 1000 10000
Off-Axis Vertical (up)Half Space Mag [dB] (0°) Mag [dB] (10°)Mag [dB] (20°) Mag [dB] (30°) Mag [dB] (40°)
Half-space 0° 10° 20° 30° 40°
Passive LF HF Half-space 0° 10° 20° 30° 40°
VERTICAL OFF-AXIS DOWN RESPONSE (dB)10
VERTICAL OFF-AXIS UP RESPONSE (dB)10
BEAMWIDTH (Degrees)12
HORIZONTAL OFF-AXIS RESPONSE (dB)10
70
80
90
100
110
70
80
90
100
110
70
80
90
100
110
360
100
10
AXIAL PROCESSED RESPONSE (dB)8
80
90
100
110
120
10 100 1000 10000
Am
pli
tud
e (d
B S
PL)
Frequency (Hz)
Frequency Response Component/System (Axially Processed)LF_proc HF_proc HalfSpace_Proc System_Proc
Frequency (Hz)100 1000 1000020
Full Range Half Space LF HF
80
90
100
110
120
10 100 1000 10000
Am
pli
tud
e (
dB
SP
L)
Frequency (Hz)
Sys / Component Axial Sensitivity (dB SPL)
Frequency (Hz)100 1000 1000020
Passive Half Space LF HF
AXIAL PROCESSED RESPONSE (dB)8
AXIAL SENSITIVITY (dB SPL)9
80
90
100
110
120
80
90
100
110
120
0
10
20
30
40
10 100 1000 10000
Directivity Index
100 1000 10000Frequency (Hz)
20
DIRECTIVITY INDEX (dB)11
20
40
10
30
0
I SERIES Point Source 600
IP6-1152/66 MEDIUM POWER 15-INCH TWO-WAY 60° x 60° INSTALLATION LOUDSPEAKER
HORIZONTAL POLAR DATA (30dB Scale, 6dB per major division)
VERTICAL POLAR DATA (30dB Scale, 6dB per major division)
-6
— 100 Hz— 125 Hz— 160 Hz— 200 Hz
-90° right
45°135°
90° left
-45°-135°
0°front
180°back
— 250 Hz— 315 Hz— 400 Hz— 500 Hz
— 630 Hz— 800 Hz— 1000 Hz— 1250 Hz
-90° right
45°135°
90° left
-45°-135°
0°front
180°back
-90° right
45°135°
90° left
-45°-135°
0°front
180°back
— 10000 Hz— 12500 Hz— 16000 Hz
-90° right
45°135°
90° left
-45°-135°
0°front
180°back
— 4000 Hz— 5000 Hz— 6300 Hz— 8000 Hz
-90° right
45°135°
90° left
-45°-135°
0°front
180°back
— 1600 Hz— 2000 Hz— 2500 Hz— 3150 Hz
-90° right
45°135°
90° left
-45°-135°
0°front
180°back
-6
— 100 Hz— 125 Hz— 160 Hz— 200 Hz
-90° down
45°135°
90° up
-45°-135°
0°front
180°back
— 250 Hz— 315 Hz— 400 Hz— 500 Hz
— 630 Hz— 800 Hz— 1000 Hz— 1250 Hz
-90° down
45°135°
90° up
-45°-135°
0°front
180°back
-90° down
45°135°
90° up
-45°-135°
0°front
180°back
— 10000 Hz— 12500 Hz— 16000 Hz
-90° down
45°135°
90° up
-45°-135°
0°front
180°back
— 4000 Hz— 5000 Hz— 6300 Hz— 8000 Hz
-90° down
45°135°
90° up
-45°-135°
0°front
180°back
— 1600 Hz— 2000 Hz— 2500 Hz— 3150 Hz
-90° down
45°135°
90° up
-45°-135°
0°front
180°back
TEC
HN
ICA
L D
RA
WIN
G /
DIM
ENSI
ON
S /
FIN
ISH
I SERIES Point Source 600
FRO
NT
SID
ES
BA
CK
TOP
/BO
TTO
M
NO
TES:
1.S
YM
BO
LIN
DIC
ATE
SC
OG
.2.
SY
MB
OL
IND
ICA
TES
MO
UN
TIN
GP
OIN
T,M
10TH
RE
AD
ED
HO
LE.
3.D
RA
WIN
GR
EP
RE
SE
NTA
TIV
EO
FIP
6-11
52/6
4,IP
6-11
52/6
6,IP
6-11
52/9
4,IP
6-11
52/9
6,IP
6-11
52/9
9,IP
6-11
52/2
6.30.8
0"[7
82.3
]
1.38
"[35
.0]
28.0
4"[7
12.3
]
CL
28.0
4"[7
12.3
]
1.38
"[35
.0]
15.8
7"[4
03.1
]
7.06
"[17
9.2]
4.71
"[11
9.6]
4.26
"[10
8.1]
INP
UT
CL10
.83"
[275
.1]
1.38
"[35
.0]
20.0
7"[5
09.7
]
30° 16
.50"
[419
.1]
1.38
"[35
.0]
9.70
"[24
6.3]
6.75
"[17
1.5]
TSC
10.8
4"[2
75.4
]
GR
ILLE
PA
RTI
ALLY
SH
OW
N
THIS
DR
AW
ING
HA
SB
EE
NFU
RN
ISH
ED
BY
CO
MM
UN
ITY
LIG
HT
&S
OU
ND
,IN
C.
THE
INFO
RM
ATI
ON
AN
DK
NO
W-H
OW
THE
RE
ON
MA
YN
OT
BE
US
ED
NO
RTH
ED
RA
WIN
GR
EP
RO
DU
CE
DW
ITH
OU
TTH
EW
RIT
TEN
PE
RM
ISS
ION
OF
CO
MM
UN
ITY
.
333
EFI
FTH
ST.
CH
ES
TER
,PA
1901
3-45
11U
SA
CO
MM
UN
ITY
PR
OFE
SS
ION
AL
LOU
DS
PE
AK
ER
S
TEL:
(610
)876
-340
0FA
X:(
610)
874-
0190
ALL
RE
PR
OD
UC
TIO
NS
WH
OLE
OR
INP
AR
T,IN
CLU
DIN
GV
EN
DO
R'S
SH
OP
DO
NO
TS
CA
LED
RA
WIN
GD
ES
CR
IPTI
ON
RE
VIS
ION
SR
EV
DA
TE
SC
ALE
DW
GN
O.
SH
EET
ALL
DIM
EN
SIO
NS
INin
/mm
U.O
.S.
THIR
DA
NG
LEP
RO
JEC
TIO
N
DR
AW
ING
TITL
E
DR
AW
ING
SS
HA
LLB
EA
RO
RR
EFE
RTO
THIS
STA
MP
.
REV
ABCDEE D C B A
12
34
56
7
12
34
56
7
UN
LES
SO
THE
RW
ISE
NO
TED
TOB
E:
AN
GLE
S:±
.5°
DE
CIM
ALS
:±.
03"
TOLE
RA
NC
ES
ON
ALL
DIM
EN
SIO
NS
ME
TRIC
:±0
.5m
m
ww
w.c
omm
unity
pro.
com
TOB
ES
YM
ME
TRIC
AL
DIM
EN
SIO
NS
AC
RO
SS
CE
NTE
RLI
NE
S
TSC
=TH
EO
RE
TIC
AL
SH
AR
PC
OR
NE
R
ISE
RIE
SIP
6-11
52
0
1O
F1
NO
NE
IP6-
1152
-2D
4.W
EIG
HT:
LOU
DS
PE
AK
ER
ON
LY:7
8LB
S.(
35.4
KG
)
1.38
"[35
.0]
15.6
3"[3
97.0
]
9.50
"[24
1.3]
NO
TTO
SCAL
E
IP6-1152/66 MEDIUM POWER 15-INCH TWO-WAY 60° x 60° INSTALLATION LOUDSPEAKER
H x
W x
D30
.80"
x 1
6.50
" x 2
0.07
"
(7
82
x 4
19 x
510
mm
)
Uni
t W
eigh
t79
lbs
(35.
8 k
g) lo
udsp
eake
r onl
y
Ship
ping
Wei
ght
92.0
lbs
(41.7
kg)
Indo
or M
odel
s:
Gril
le: P
owde
r-co
ated
per
fora
ted
stee
l bac
ked
wit
h co
lor-
mat
ched
aco
usti
cally
tran
spar
ent w
oven
fabr
ic.
Bla
ck (R
AL9
005)
or W
hite
(RA
L900
3)
Enc
losu
re /
Fini
sh: B
lack
(RA
L900
5) o
r Whi
te
(RA
L900
3) lo
w g
loss
, uni
form
ly te
xtur
ed p
aint
ed 1
5mm
B
alti
c B
irch
ply
woo
d.
*Out
door
Mod
els:
G
rille
: Mar
ine
grad
e al
umin
um w
ith
zinc
-ric
h du
al-l
ayer
gre
y po
wde
r-co
at, f
eatu
ring
hyd
roph
obic
tr
eatm
ent o
f aco
usti
cally
tran
spar
ent w
oven
bla
ck
fabr
ic b
acki
ng.
Enc
losu
re /
Fini
sh: 1
5mm
Pol
yGla
s™, G
rey
(RA
L703
8),
heav
ily te
xtur
ed in
dust
rial
-gra
de e
xter
ior-
rate
d co
atin
g. B
lack
, Whi
te o
r Cus
tom
col
ors
upon
req
uest
.
*Not
e: T
he o
utdo
or m
odel
dra
win
g is
ava
ilabl
e at
com
mun
ityp
ro.c
om -
Inpu
t pan
el a
nd
mou
ntin
g po
int l
ocat
ions
and
the
unit
wei
ght m
ay v
ary
from
indo
or m
odel
(sho
wn)
.
Community Professional Loudspeakers333 East Fifth Street, Chester, PA 19013-4511 USAPhone (610) 876-3400 • Fax (610) 874-0190communitypro.com • [email protected]
CAUTION: Installation of loudspeakers should only be performed by trained and qualified personnel. It is strongly recommended that a licensed and certified professional structural engineer approve the mounting design.
IP6-1152/66 [07JUN2016]
I SERIESPoint Source 600
IP6-1152/66MEDIUM POWER 15-INCH TWO-WAY 60° x 60° INSTALLATION LOUDSPEAKER
NOTES
Two-way single amp
CONNECTION DIAGRAMS
Two-way biamp
HF
LFPassiveThru
PassiveInput
+/–
+/–
Crossover
AmpDSP
HF
LFLF Input
HF Input
+/–
+/–DSP
HF Amp
LF Amp
Two-way input panel
1. PERFORMANCE SPECIFICATIONS All measurements are taken indoor using a time-windowed and processed signal to eliminate room effects, approximating an anechoic environment, a distance of 6.0 m. All acoustic specifications are rounded to the nearest whole number. An external DSP with settings provided by Community Professional Loudspeakers is required to achieve the specified performance; further performance gains can be realized using Community’s dSPEC226 loudspeaker processor with FIR power response optimization.
2. OPERATING RANGE The frequency range in which the on-axis processed response remains within 10dB of the average SPL.
3. CONTINUOUS POWER HANDLING Maximum continuous input voltage (and the equivalent power rating, in watts, at the stated nominal impedance) that the system can withstand, without damage, for a period of 2 hours using an EIA-426-B defined spectrum; with recommended signal processing and protection filters.
4. NOMINAL SENSITIVITY Averaged SPL over the operating range with an input voltage that would produce 1 Watt at the nominal impedance and the averaged SPL over the operating range with a fixed input voltage of 2.83V, respectively; swept sine wave axial measurements with no external processing applied in whole space, except where indicated.
5. NOMINAL MAXIMUM SPL Calculated based on nominal / peak power handling, respectively, and nominal sensitivity; exclusive of power compression.
6. EQUALIZED SENSITIVITY The respective SPL levels produced when an EIA-426-B signal is applied to the equalized loudspeaker system at a level which produces a total power of 1 Watt , in sum, to the loudspeaker subsections and also at a level which produces a total voltage, in sum, of 2.83V to the loudspeaker subsections, respectively; each referenced to a distance of 1 meter.
7. EQUALIZED MAXIMUM SPL The SPL produced when an EIA-426-B signal is applied to the equalized loudspeaker system, at a level which drives at least one subsection to its rated continuous input voltage limit, referenced to a distance of 1 meter. The peak SPL represents the 2:1 (6dB) crest factor of the EIA-426-B test signal.
8. AXIAL PROCESSED RESPONSE The on-axis variation in acoustic output level with frequency of the complete loudspeaker system with recommended signal processing applied. 1/6 octave Gaussian smoothing applied.
9. AXIAL SENSITIVITY The on-axis variation in acoustic output level with frequency for a 1 Watt swept sine wave, referenced to 1 meter with no signal processing. 1/6 octave Gaussian smoothing applied.
10. HORIZONTAL / VERTICAL OFF-AXIS RESPONSES The loudspeaker’s magnitude response at various angles off-axis, with recommended signal processing applied in the operating mode which utilizes the largest number of individually amplified pass bands. 1/6 octave Gaussian smoothing applied.
11. DIRECTIVITY INDEX The ratio of the on-axis SPL squared to the mean squared SPL at the same distance for all points within the measurement sphere for each given frequency; expressed in dB. 1/6 octave Gaussian smoothing applied.
12. BEAMWIDTH The angle between the -6dB points in the polar response of the loudspeaker when driven in the operating mode which utilizes the largest number of individually amplified pass bands. 1/6 octave Gaussian smoothing applied.
Data presented on this spec sheet represents a selection of the basic performance specifications for the model. These specifications are intended to allow the user to perform a fair, straightforward evaluation and comparison with other loudspeaker spec sheets. For a detailed analysis of this loudspeaker’s performance, please download the GLL file and/or the CLF file from our website: communitypro.com.