hw install quick reference guide

8/22/2019 HW Install Quick Reference Guide

1/25

.

FlexiPacket MultiRadio

HW Install Quick Reference Guide

A25000-A1600-A032-01-76P1

Issue: 1 Issue date: January 2011


2/25

.

.2 A25000-A1600-A032-01-76P1



The information in this document is subject to change without notice and describes only the

product defined in the introduction of this documentation. This documentation is intended for the

use of Nokia Siemens Networks customers only for the purposes of the agreement under whichthe document is submitted, and no part of it may be used, reproduced, modified or transmitted

in any form or means without the prior written permission of Nokia Siemens Networks. The

documentation has been prepared to be used by professional and properly trained personnel,

and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes

customer comments as part of the process of continuous development and improvement of the

documentation.

The information or statements given in this documentation concerning the suitability, capacity,

or performance of the mentioned hardware or software products are given "as is" and all liability

arising in connection with such hardware or software products shall be defined conclusively and

finally in a separate agreement between Nokia Siemens Networks and the customer. However,

Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions

contained in the document are adequate and free of material errors and omissions. Nokia

Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which

may not be covered by the document.

Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO

EVENT WILL NOKIA SIEMENS NETWORKS BE LIABLE FOR ERRORS IN THIS DOCUMEN-

TATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT,

INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT

LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS

OPPORTUNITY OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR

THE INFORMATION IN IT.

This documentation and the product it describes are considered protected by copyrights and

other intellectual property rights according to the applicable laws.

The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark

of Nokia Corporation. Siemens is a registered trademark of Siemens AG.

Other product names mentioned in this document may be trademarks of their respectiveowners, and they are mentioned for identification purposes only.

Copyright Nokia Siemens Networks 2011. All rights reserved.

f Important Notice on Product SafetyThis product may present safety risks due to laser, electricity, heat, and other sources

of danger.

Only trained and qualified personnel may install, operate, maintain or otherwise handle

this product and only after having carefully read the safety information applicable to this

product.

The safety information is provided in the Safety Information section in the Legal, Safety

and Environmental Information part of this document or documentation set.

The same text in German:

f Wichtiger Hinweis zur ProduktsicherheitVon diesem Produkt knnen Gefahren durch Laser, Elektrizitt, Hitzeentwicklung oder

andere Gefahrenquellen ausgehen.

Installation, Betrieb, Wartung und sonstige Handhabung des Produktes darf nur durch

geschultes und qualifiziertes Personal unter Beachtung der anwendbaren Sicherheits-

anforderungen erfolgen.

Die Sicherheitsanforderungen finden Sie unter Sicherheitshinweise im Teil Legal,

Safety and Environmental Information dieses Dokuments oder dieses Dokumentations-

satzes.


3/25

.

.

A25000-A1600-A032-01-76P1


3


Table of ContentsThis document has 25 pages.

1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2 FlexiPacket MultiRadio installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.2 Installing the antenna. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.3 Installing the FlexiPacket MultiRadio . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3 FlexiPacket MultiRadio installation on already installed FlexiHopper anten-

nas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4 Indoor Power Injector installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.1 Installation in the rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.2 External connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.3 Indoor Power Injector grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4.4 Power Supply connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4.5 IDU CABLE connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4.6 ODU CABLE connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

4.7 ALMs Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

5 Outdoor Power Injector installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

5.1 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

5.2 External connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

5.3 Outdoor Power Injector grounding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

5.4 Power Supplyconnection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

5.5 IDU CABLE connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

5.6 ODU CABLE connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

6 Finalising the alignment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24


4/25

.

.4 A25000-A1600-A032-01-76P1



List of FiguresFigure 1 FH Adapter detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Figure 2 FH Adapter installed on the FlexiPacket MultiRadio. . . . . . . . . . . . . . . . 12

Figure 3 Indoor Power Injector (Indoor 4 ports) . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Figure 4 Indoor Power Injector connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Figure 5 PS connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Figure 6 IDU CABLE connector front view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Figure 7 ODU CABLE connector front view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Figure 8 ALMs connector front view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Figure 9 Power Injector connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Figure 10 Outdoor Power Injector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Figure 11 Outdoor Power Injector connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Figure 12 Outdoor Power Injector grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Figure 13 PS connector inside the Outdoor Power Injector . . . . . . . . . . . . . . . . . . 20Figure 14 Power cable installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Figure 15 IDU CABLE connector front view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Figure 16 ODU CABLE connector front view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23


5/25

.

.

A25000-A1600-A032-01-76P1


5


List of TablesTable 1 PS connector pin function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Table 2 IDU CABLE connector pin function . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Table 3 ODU CABLE connector pin function . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Table 4 ALMs connector pin function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Table 5 PS connector pin function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Table 6 IDU CABLE connector pin function . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Table 7 ODU CABLE connector pin function . . . . . . . . . . . . . . . . . . . . . . . . . . . 23


6/25

.

.6 A25000-A1600-A032-01-76P1




7/25

.

.

A25000-A1600-A032-01-76P1


7

HW Install Quick Reference Guide Overview

1 OverviewFlexiPacket MultiRadio is compatible with the XD antennas.

tFor the compatibility with the FlexiHopper antennas a special adapter (to be installed onthe FlexiPacket MultiRadio) is available.

The FlexiPacket Radio is connected to the Indoor Device by using:

2 cables (1 cable for the Ethernet interface to be connected to the Ethernet connec-

tor and 1 cable for the Power Supply to be connected to the PS connector).

1 cable only to be connected to the Ethernet connector, if the Power+Ethernet

solution has been used. In this case the Power Injector must be installed (refer to

Chapter4 for the Indoor Power Injector and to Chapter5 for the Outdoor Power

Injector).

t

For the information regarding the connectors, the cable termination, the grounding, the

tools to be used and the cable fixing refer to the "HW Install" document.

t This Quick Reference Guide gives the information to install the 1+0 configuration withthe integrated antenna.

For the other configurations refer to the "HW Install" document.

t To install the Ethernet Repeater (if required), refer to the "HW Install" document.


8/25

.

.8 A25000-A1600-A032-01-76P1


HW Install Quick Reference GuideFlexiPacket MultiRadio installation

2 FlexiPacket MultiRadio installation

2.1 OverviewVerify to have the correct parts and equipment (outdoor unit with correct frequency band

and sub-band, and a corresponding antenna). Check that it has not been damaged

during transportation.

The following parts and tools are needed in the installation:

FlexiPacket MultiRadio

XD FlexiPacket MultiRadio antenna

Ethernet cable and the Power Supply cable (if the solution with a dedicated power

supply cable has been implemented) with recommended connectors (waterproof),

cable ties or cable clamps

grounding wire

two 13 mm and 17 mm fork or ring spanners (two needed for tightening the locking

screws)

5 mm and 6 mm Allen keys/torque spanner (optional)/cordless drill (optional)/DC

voltage meter and cable with a BNC connector.


9/25

.

.

A25000-A1600-A032-01-76P1


9

HW Install Quick Reference Guide FlexiPacket MultiRadio installation

2.2 Installing the antenna

Remove tape

When fitting, torque

nuts to 22 Nm

Horizontal

locking

screw

Horizontal

adjustment

Vertical

adjustment

Vertical

locking

screws

Tighten to 20 Nm

Antenna mounted

on the pole mount

(offset left)

M10

largewasher

M10lockwasher M10

hex nut

Vertical

adjustment

Horizontal

adjustment


10/25

.

.10 A25000-A1600-A032-01-76P1


HW Install Quick Reference GuideFlexiPacket MultiRadio installation

2.3 Installing the FlexiPacket MultiRadio

Horizontal installation

(H)

Vertical installation

(V)

Do not remove

sellotape!

Guide/pin hole

ODU transition plate

Hook


11/25

.

.

A25000-A1600-A032-01-76P1


11

HW Install Quick Reference Guide FlexiPacket MultiRadio installation

g Never peel off or damage the foil covering the waveguide opening of the outdoor unit.This may result in equipment failure over time if moisture or particles get inside the unit.

t Follow local requirements for earthing (grounding). The principles and requirementsvary in different countries.


12/25

.

.12 A25000-A1600-A032-01-76P1


HW Install Quick Reference GuideFlexiPacket MultiRadio installation on already installedFlexiHopper antennas

3 FlexiPacket MultiRadio installation on

already installed FlexiHopper antennas

One FH Adapter must be installed on the FlexiPacket MultiRadio and then the assemblymust be mounted on the FH Coupler.

Figure 1 FH Adapter detail

Fix the FH Adapter on the FlexiPacket MultiRadio as shown in Figure 2 by using the 4screws provided with the adapter.

Figure 2 FH Adapter installed on the FlexiPacket MultiRadio


13/25

.

.

A25000-A1600-A032-01-76P1


13

HW Install Quick Reference Guide Indoor Power Injector installation

4 Indoor Power Injector installation

Figure 3 Indoor Power Injector (Indoor 4 ports)

4.1 Installation in the rack

Install the Indoor Power Injector in the rack (19 or N3) by using the relevant brackets

provided with the Indoor Power Injector.

4.2 External connections

The second Power Source can be used to provide Power Supply redundancy.

To semplify in Figure 4 only one port is shown, but the Indoor Power Injector can be used

with up to four ports.

Figure 4 Indoor Power Injector connections


14/25

.

.14 A25000-A1600-A032-01-76P1


HW Install Quick Reference GuideIndoor Power Injector installation

t Insert a 6 A breaker for four ports (1.5 A each used port) between the negative pole ofthe battery and the Indoor Power Injector.

4.3 Indoor Power Injector groundingThe Indoor Power Injector must be grounded by connecting the grounding point on the

side to the rack ground by using the grounding cable provided with the Indoor Power

Injector.

4.4 Power Supply connection

Figure 5 PS connector

4.5 IDU CABLE connection

Use the optional Ethernet cable.

The Ethernet connector is shown in Figure 6 and described in Table 2.

Figure 6 IDU CABLE connector front view

Signal name

48 V + (Left side pin)

48 V - (Right side pin)

Table 1 PS connector pin function

Pin # Pair Cable colour Function

1 TP3+ white/green Bi-directional pair 3+

2 TP3- green Bi-directional pair 3 -

3 TP2+ white/orange Bi-directional pair 2+

4 TP1+ blue Bi-directional pair 1+

5 TP1- white/blue Bi-directional pair 1-

6 TP2- orange Bi-directional pair 2-

Table 2 IDU CABLE connector pin function


15/25

.

.

A25000-A1600-A032-01-76P1


15

HW Install Quick Reference Guide Indoor Power Injector installation

4.6 ODU CABLE connection

The ODU CABLE connector implements the Power+Ethernet (P+E): it is in charge of

carrying both power and data over the same cable.

The ODU CABLE connector is shown in Figure 7 and described in Table 3.

Figure 7 ODU CABLE connector front view

4.7 ALMs Connector

The Indoor Power Injector has a standard RJ45 connector on the front panel for Alarms

reporting.

The RJ-45 connector is provided with the Indoor Power Injector.

Use the same cable use also for the IDU-ODU connection.

7 TP4+ white/brown Bi-directional pair 4+

8 TP4- brown Bi-directional pair 4-


Table 2 IDU CABLE connector pin function (Cont.)

Pin # Pair Cable colour Ethernet Function Power

function

Amphenol

Pin on

FlexiPacket

MultiRadio

1 TP3+ white/green Bi-directional pair 3+ -V1a 72 TP3- green Bi-directional pair 3- -V1b 3

3 TP2+ white/orange Bi-directional pair 2+ +V1a 5

4 TP1+ blue Bi-directional pair 1+ +V2a 1

5 TP1- white/blue Bi-directional pair 1- +V2b 4

6 TP2- orange Bi-directional pair 2- +V1b 2

7 TP4+ white/brown Bi-directional pair 4+ -V2a 6

8 TP4- brown Bi-directional pair 4- -V2b 8

Table 3 ODU CABLE connector pin function


16/25

.

.16 A25000-A1600-A032-01-76P1


HW Install Quick Reference GuideIndoor Power Injector installation

Figure 8 ALMs connector front view

Pin # Ethernet Function

1-2 Short circuit on ODU 1 power supply




Table 4 ALMs connector pin function


17/25

.

.

A25000-A1600-A032-01-76P1


17

HW Install Quick Reference Guide Outdoor Power Injector installation

5 Outdoor Power Injector installationFigure 9 shows the connections to be made for the Power Injector.

Figure 9 Power Injector connections

t Insert a 3 A breaker between the negative pole of the battery and the Power Injector.


18/25

.

.18 A25000-A1600-A032-01-76P1


HW Install Quick Reference GuideOutdoor Power Injector installation

Figure 10 Outdoor Power Injector

5.1 Installation

The Outdoor Power Injector can be installed on the wall or on the pole.For the details refer to Chapter 8 of the HW Install document.


19/25

.

.

A25000-A1600-A032-01-76P1


19


5.2 External connections

Figure 11 Outdoor Power Injector connections

5.3 Outdoor Power Injector groundingGrounding cable: from system ground point to Outdoor Power Injector external ground

point, 2 meters long, single wire, 6mm cross sectional area, green colour, for outdoor

use.

Cable terminal shall be an M6 ring type. The other cable side shall be supplied without

a terminal. During installation, ground cable can be cut at a proper length and terminated

with a M8 ring terminal that shall be supplied as well.

Figure 12 Outdoor Power Injector grounding


20/25

.

.20 A25000-A1600-A032-01-76P1



5.4 Power Supplyconnection

Figure 13 PS connector inside the Outdoor Power Injector


21/25

.

.

A25000-A1600-A032-01-76P1


21


Fix the two wires to the positive and the negative poles of the power supply connector

inside the Outdoor Power Injector using a screwdriver.

Figure 14 Power cable installation

5.5 IDU CABLE connection

Use the optional Ethernet cable.

The Ethernet connector is shown in Figure 15 and described in Table 6.

Signal name

48 V + (Left side pin)

48 V - (Right side pin)

Table 5 PS connector pin function


22/25

.

.22 A25000-A1600-A032-01-76P1



Figure 15 IDU CABLE connector front view

5.6 ODU CABLE connection

The ODU CABLE connector implements the Power+Ethernet (P+E): it is in charge of

carrying both power and data over the same cable.

The ODU CABLE connector is shown in Figure 16 and described in Table 7.


1 TP3+ white/green Bi-directional pair 3+

2 TP3- green Bi-directional pair 3 -

3 TP2+ white/orange Bi-directional pair 2+

4 TP1+ blue Bi-directional pair 1+

5 TP1- white/blue Bi-directional pair 1-

6 TP2- orange Bi-directional pair 2-

7 TP4+ white/brown Bi-directional pair 4+

8 TP4- brown Bi-directional pair 4-

Table 6 IDU CABLE connector pin function


23/25

.

.

A25000-A1600-A032-01-76P1


23


Figure 16 ODU CABLE connector front view

Pin # Pair Cable colour Ethernet Function Power

function

Amphenol

Pin on

FlexiPacket

MultiRadio

1 TP3+ white/green Bi-directional pair 3+ -V1a 7

2 TP3- green Bi-directional pair 3- -V1b 3

3 TP2+ white/orange Bi-directional pair 2+ +V1a 5

4 TP1+ blue Bi-directional pair 1+ +V2a 1

5 TP1- white/blue Bi-directional pair 1- +V2b 4

6 TP2- orange Bi-directional pair 2- +V1b 2

7 TP4+ white/brown Bi-directional pair 4+ -V2a 6

8 TP4- brown Bi-directional pair 4- -V2b 8

Table 7 ODU CABLE connector pin function


24/25

.

.24 A25000-A1600-A032-01-76P1


HW Install Quick Reference GuideFinalising the alignment

6 Finalising the alignment

t The LCT is needed for setting the radio parameters.Check that Automatic Tx Power Control setting is OFF at both ends of the hop when per-forming fine alignment.

Before fine alignment can be done, set the correct frequency and transmit power for both

near-end and far-end radios. The FlexiPacket MultiRadio at the other end of the hop

must be pre-aligned to this station and must be sending a signal on the correct fre-

quency.

t Note that the antenna radiation pattern includes two or more side lobes and one mainlobe. The radio needs to be aligned towards the main lobe of the far-end radio. To be

sure that you have found the main lobe you also need to detect the side lobes around

the main lobe.

Check the DC voltage meter readings:

1. Connect the DC voltage meter (connector type BNC) to the AGC connector.

2. Find the minimum value for the AGC voltage by vertical and horizontal adjustments.

The smaller the voltage - the greater the received power.

Main and side lobes of the radio


25/25

.HW Install Quick Reference Guide Finalising the alignment

3. Check with the LCT that the Rx power level is within 3 dB of the value stated in the

network plan.

hw install quick reference guide

Documents