HUR PULLEY

USER MANUAL

1 ver. 1/2017

READ THIS FIRST

Prior to the use of HUR products, we recommend that you familiarize yourself with these instructions con-cerning the HUR products at your disposal. This HUR Manual is a guide for users for the operation and maintenance of HUR products. Proper use and maintenance actions will ensure a safe, enjoyable and effective workout, also extending the product life cycle. The manual also helps you to get your customers familiarized with the use of HUR products. We recommend that HUR authorized personnel carry out the installation, maintenance and repair actions. Your local HUR dealer is happy to help you if you need technical support or have HUR product-related ques-tions. It is recommended that the instructions below are followed for avoiding any injuries and damages.

Never move or tilt the equipment alone. If you need to tilt it for e.g. vacuuming, ensure the use of adequate support so that the machine cannot tip over.

Do not connect the HUR equipment with any other power sources or other parts or compo-nents than those supplied and approved by HUR.

If you discover a defect, please, contact HUR service. Do not attempt to repair it yourself.

Read the compressor manual and follow the instructions regarding the compressor operation and maintenance procedures.

Read carefully the enclosed instruction how to attach HUR Pulley to the floor. This manual portrays the general HUR Warranty Terms. Check the possible regional or customer-specific special terms from your HUR dealer. In case of a defect in your HUR product during the warranty period, the warranty covers the repair parts and components needed, as well as the repair work (excluding travel expenses). Note that the warranty does not cover any damages caused by transportation or damages caused by failure to comply with this HUR Pulley User Manual. HUR is not responsible for damages or costs caused for devices by use of any components or parts that are not manufactured by HUR. Defective equip-ment is to be taken out of service until it is properly repaired. HUR is not responsible for consequential damages caused by device failure during the time when the device is out of order. Due to continuous product development, HUR reserves the right to conduct product changes without prior notice. The content of this manual can change without prior notice.

Ab HUR OY Patamäentie 4 67100 Kokkola FINLAND Tel. +358 6 832 5500 Email: sales@hur.fi, service@hur.fi www.hur.fi

2 ver. 1/2017

INTRODUCTION

Congratulations and welcome to HUR user-family! HUR products are designed to serve You and your customers for a long and enjoyable time. In this User Manual You will find information of basic actions to put into practice for maximizing the life cycle of the products. Information covers everyday routines as well as scheduled maintenance procedures. HUR products are high-quality Finnish work. We have centralized all our operations un-der one roof and manage them according to the ISO certified quality system. Our busi-ness meets ISO 9001 quality certification requirements. Each HUR product, be it HUR fitness equipment or HUR software, has been designed, manufactured and tested at our factory in Kokkola. Your HUR dealer will be happy to answer any questions You might have concerning HUR products. You can also give them feedback of our products. HUR products are CE marked.

ORIGINAL INSTRUCTIONS

This HUR Pulley User Manual includes the original instructions that are revised 10.11.2016.

3 ver. 1/2017

CONTENT

READ THIS FIRST ................................................................................................................................................ 1

INTRODUCTION ................................................................................................................................................. 2

ORIGINAL INSTRUCTIONS .................................................................................................................................. 2

CONTENT ........................................................................................................................................................... 3

1 HUR NATURAL TRANSMISSION ...................................................................................................................... 4

2 HUR PULLEY – FUNCTIONAL TRAINER ............................................................................................................ 5

2.1 General .................................................................................................................................................... 5

2.2 Technical data .......................................................................................................................................... 5

2.3 Compositions and important information of using HUR Pulley .............................................................. 6

2.4 Installation ............................................................................................................................................... 9

2.5 Adjusting Pulley ....................................................................................................................................... 9

2.6 Exercising with Pulley ............................................................................................................................ 10

2.6.1 Adjusting the resistance and exercising ......................................................................................... 11

3 MAINTENANCE AND SERVICE ....................................................................................................................... 12

4 SAFETY PRECAUTIONS AND WARNINGS ....................................................................................................... 14

4.1 Safety precautions and warnings for users of HUR devices .................................................................. 14

4.2 Safety precautions and warnings for owners of HUR devices ............................................................... 14

5 HUR PULLEY ACCESSORIES ........................................................................................................................... 16

6 WARRANTY TERMS OF HUR OY .................................................................................................................... 18

1 GENERALLY ABOUT THE PRODUCTS ......................................................................................................... 18

2 WARRANTY ............................................................................................................................................... 18

3 WARRANTY PERIOD .................................................................................................................................. 18

4 REMEDY .................................................................................................................................................... 18

5 RESTRICTIONS ........................................................................................................................................... 18

6 NOTIFICATIONS OF A DEFECT UNDER THIS WARRANTY .......................................................................... 19

7 CONSUMER’S RIGHTS ............................................................................................................................... 19

8 REVISIONS OF THE WARRANTY ................................................................................................................ 19

9 APPLICABLE LAW ...................................................................................................................................... 19

4 ver. 1/2017

1 HUR NATURAL TRANSMISSION

HUR equipment is designed for natural muscle exercise and for establishment and improvement of muscle tone. HUR has developed a mechanism where the load changes with the trajectory, mimicking the human body’s own biomechanics. During exercise, muscle strength is at its highest mid-movement and lowest at the beginning and at the end of the movement. Incorrect or excessive exercise can cause muscle injury. This is taken into account in the HUR exercise equipment design. Thanks to use of compressed air, the resistance changes smoothly, accu-rately and safely. This allows the equipment to function in an optimal way for the muscles, during both slow and fast movements. The equipment cylinders and lever arms’ resistance is at its greatest when the muscle is aiming for maxi-mum power. With HUR exercise equipment your muscles do the work, reducing the wear and tear on joints and connective tissue. This mechanism optimizes the use of muscle power and reduces the possibility of exercising in a wrong way. The biggest problem with traditional weight stack machines is the weight stack’s inertia. At the beginning of the exercise movement, extra power is required to move a weight stack. At the end of the movement, the resistance lightens as the weight stack continues to move before it changes direction. This can cause undue stress on the joints and connective tissues, especially for people who are not used to this kind of muscles. The human body is composed of muscles that work in pairs. When the flexor muscle flexes, the opposite extensor extends. HUR has designed dual function equipment, so that all muscle groups are exercised. All of these factors combined ensure a safe, relaxed and comfortable workout. A natural way to exercise!

5 ver. 1/2017

2 HUR PULLEY – FUNCTIONAL TRAINER

2.1 General

For variety of lower, mid and upper body exercises

Adjustable height cable column Dual handles for unilateral movement on all exercises

Features:

Instead of using weight stacks, HUR machines use pneumatic technology meaning perfect balance between exercise load and muscle’s output force, regardless of the speed of motion.

Welded steel frame with similar engineering as on automotive industry gives rigid, yet lightweight construction.

Aluminum side rails.

Dark lexan panels cover all the internal parts – a safety feature that also looks good.

Frame is powder coated for smooth finish and very good wear resistance.

Design of the machines gives a luxurious look to your facility.

Steplessly adjustable exercise load enables just the right resistance to each user.

Standard features are leg strap, two hand grips and adjustable support handles on both sides.

The frame design also enables exercising of wheelchair users.

Dual handles and an adjustable height cable column enable performing numerous exercises.

With a wide range of accessories HUR Pulley is suitable for exercising of entire body. Control panel options:

color touch screen: o shows the resistance, repetitions and heart rate value (requires a Polar-compatible heart

rate belt)

analog display with push buttons: o the resistance is shown analogically on the range 0–20 kg or 0–30 kg.

2.2 Technical data

6 ver. 1/2017

Load range: Stepless adjustment 8820: 2–20 kg (per rope) 8830: 4–30 kg (per rope)

Number of cylin-ders:

1

Max. input pres-sure:

9,9 bar

Frame: Welded steel construction with aluminum side rails. Stainless steel fasteners. Powder coated. Contact your local HUR distributor for standard and optional color specifications.

Controls and displays:

COLOR TOUCH SCREEN: The resistance is adjusted by touching the buttons in the touch screen. The re-sistance, repetitions, instructions and heart rate value (requires a Polar-compatible heart rate belt) are shown on the touch screen. ANALOG DISPLAY: The resistance is adjusted by push buttons and is shown analogically.

Dimensions (W/L/H): 8820/8830: 798 x 901 x 2185 mm (wall mounted) 43 kg

8821/8831: 1368 x 1363 x 2195 mm (floor mounted) 66 kg ST8820/ST8830: 798 x 901 x 2185 cm (wall mounted) 46 kg ST8821/ST8831: 1368 x 1363 x 2195 cm (floor mounted) 69 kg

Weight: Pulley. 43 - 69 kg

Noise: ≤ 50 dB

Standards: ISO 9001, SFS-EN ISO 20957-1, SFS-EN 957-2

Warranty: 10 years for the frame; 3 years for other parts excluding electronics; 1 year for electronics

2.3 Compositions and important information of using HUR Pulley

HUR Pulley is available with two different cylinder sizes: the maximum load of 8830/8831 Pulley is 30 kg per rope, and of 8820/8821 Pulley Light 20 kg per rope. There is no difference in the looks of the two Pul-leys. HUR Pulleys are available either with Pulley wall mount (8820/8830), when the machine is fastened to the wall by bolts; or with Pulley floor mount legs (8821/8831), when it is possible to attach and place the ma-chine even in the center of the floor. (NOTE! 8821 / 8831 pulleys shall be fixed to floor to ensure stability.) Other HUR Pulley compositions and accessories are introduced in the chapter 5. Depending on the composition the dimensions (see Technical data) may vary. That should be taken into account in placing the machine and determining the zones of usage and safety.

7 ver. 1/2017

Pulley wall mount (8820/8830) - Dimensions are expressed in millimeters (mm) and inches (in) - The usage zone is the area within the support handles (see the lowest picture) and it means how

much the rope is allowed to be pulled in lateral (45°/90°) - The safety zone is 500 mm (20 in) on the both sides of the machine. - Depending on the exercise the safety zone varies in front of the machine (the rope length + the

space that user needs + safety zone of 500 mm). - To avoid damages, stop exercising immediately if other person enters the safety zone.

2185mm (86in)

4090mm (161,0 in)

Max 901mm (35,5in)

+500mm (20in) +500mm (20in)

Max 90 (45/45)

798mm (31,4in)

8 ver. 1/2017

Pulley floor mount (8821/8831) - Dimensions are expressed in millimeters (mm) and inches (in) - The usage zone is the area within the legs (see the lowest picture) and it means how much the rope

is allowed to be pulled in lateral (45°/90°) - The safety zone is 500 mm (20 in) on the both sides of the machine. - Depending on the exercise the safety zone varies in front of the machine (the rope length + the

space that user needs + safety zone of 500 mm). - To avoid damages, stop exercising immediately if other person enters the safety zone.

-

1363mm (53,7 in)

2195mm (86,4 in)

4230mm (166,7 in)

1368mm (53,9 in)

Max 90 (45/45)

+500mm (20 in) +500mm (20 in)

9 ver. 1/2017

2.4 Installation

HUR recommends that the installation of HUR Pulleys is performed by authorized HUR technician. In that case the reliability of the installation will be reached. HUR technician has all needed tools and in-structions for installation and also has knowledge of all special characteristics of each machine. HUR devices are designed only for inside use. Devices must not get wet and it’s recommendable to avoid moisture. All models with electronic components should be left to acclimate to room temperature for about an hour before installing or operating, if the transportation or storage has been in a cold place. Equipment should be placed on a hard, flat and straight surface. To avoid malfunction, keep the unit in a dry place and at constant temperature protected from dust.

WARNING! Floor mounted equipment shall be installed on a stable and levelled base.

Hur Pulley floor mounted models 8831, ST8831 MUST BE ATTACHED TO FLOOR.

2.5 Adjusting Pulley

Pull the orange handle located on the side of the cable column and adjust the height by moving the cable column up or down. Make sure that the cable column is properly locked.

WARNING! Make sure that the rod of the handle slides properly back inside to its slot

after adjusting the cable column. Otherwise, the cable column may move and cause a dangerous situation. If you need the support handles, pull the orange han-dle next to the frame and adjust the handles to desired level. Make sure that the rod of the handle slides back to its slot.

10 ver. 1/2017

Choose a bar, a grip or a strap and attach it to the cable end by quick access fastener.

2.6 Exercising with Pulley

Pulley is created for variety of lower, mid and upper body exercises. The device comes with instructions for the most common exercises, and these illustrated instructions are recommended to be placed in a promi-nent location near equipment. More instruction for exercising with HUR Pulley is on a video ’HUR Pulley – Functional Trainer’. https://youtu.be/Hpa9B4FTZhk In addition to general introduction, 17 basic exercises for lower, mid and upper body are shown. HUR Pulley is designed and intended for exercising muscles and strength. With standard equipment, a pair of hand grips and a leg strap, it’s possible to exercise muscles of, for example, arms, legs and upper body. With Pulley accessories it is possible to make exercising more comprehensive. Popular Pulley accessories are, for example, Pulley rowing bench, triceps and pull-down grips and straps. They make it easy to target different parts of body and special muscles. Remarkable is that HUR Pulley can be used by wheelchair-users, too.

NOTE!

HUR products are designed and intended for gym, health club and rehabilitation use only. HUR product shall be used only in their designed and intended use. Incorrect use may result in personal injury and equipment damage. Incorrect use may remove the manufacturer's responsibility and void the warranty. Incorrect use means all actions that are against the intended use of HUR products, and all actions against or failure to follow instructions in this User Manual. To avoid injuries and damages, pay attention to following:

Do not pull the ropes too far to the side (max. 45°/90°), because the rope may stuck between the rollers.

Support handles are intended to give support. They shall not be used for dipping, climbing or carry-ing the machine.

Avoid yanks and other fast movements when exercising with low resistance. The cylinder that cre-ates the resistance does not accommodate with fast movements and the ropes may jump out of the rollers.

If there’s pressure in the device, the ropes should not be pulled out and let off abruptly, because the pressure pulls the rope back to the device and that can cause the rollers break if, for example, a bar or a grip hits them hard.

WARNING! Incorrect or excessive exercising might damage your health.

11 ver. 1/2017

2.6.1 Adjusting the resistance and exercising

Adjusting Pulley with Analog

1. Adjust the resistance by pressing plus (+) and minus (-) buttons. 2. After having finished your exercise release the resistance by pressing

minus (-) button.

Adjusting Pulley with Touch screen a) Exercising without SmartCard:

1. Adjust the resistance by pressing plus (+) and minus (-) but-tons on the screen.

2. After having finished your exercise release the resistance by pressing minus (-) button or “Release” button on the screen.

b) Exercising with SmartCard:

1. Upload the exercising program to SmartCard in the HUR SmartCard Kiosk. 2. Get into machine, insert SmartCard to card reader and choose exercise. Follow instructions shown

on the screen. 3. Resistance will be set automatically. 4. You will hear a beeping sound after you have performed the repetitions according to your exercis-

ing program. 5. Follow the instructions on the screen and take SmartCard out of the card reader. 6. Save your data and log out in the HUR SmartCard Kiosk.

c) Exercising with RFID-tag:

1. Show the RFID-tag to the reader and select exercise. 2. Resistance will be set automatically. 3. You will hear a beeping sound after you have performed the repetitions according to your exercis-

ing program. 4. Follow the instructions on the screen.

WARNING! Do not press plus (+) and minus (-) buttons simultaneously. Simultaneous pressing of the buttons lets the pressure directly through the device, which causes an unnecessary load on the pressure network, and can reduce the equipment’s life cycle.

WARNING! Heart rate monitoring systems may be inaccurate. Over exercising may result in serious injury or death. If you feel faint stop exercising immediately.

12 ver. 1/2017

3 MAINTENANCE AND SERVICE

Routine maintenance schedule: ACTION ADDITIONAL INFORMATION

DAILY

Wipe handles and control buttons.

Normal daily routine to maintain overall hygiene and comfort. Do not use cleaning products containing al-cohol. Do not use excess of water. Ensure the suitabil-ity of cleaning products to HUR devices.

WEEKLY

Wipe handles and control buttons. Disinfect if needed.

Do not use cleaning products containing alcohol. Do not use excess of water. Ensure the suitability of clean-ing products to HUR devices.

Check the water extractor tank of air pressure system.

Empty if the tank is more than half full.

Check the oil level of com-pressor motor(s).

Add oil if necessary. See detailed instructions in the compressor manual.

MONTHLY

Tilt machines (not wall mounted) and clean floor surface underneath. Do not tilt the machine without helping hand.

Wipe the floor or use vacuum cleaner. Be careful not to cause too much tension on tubes or electric wiring when tilting machine. Avoid hitting components in-stalled to the bottom of the machine.

Inspect ropes and rollers visually.

Worn ropes need to replaced immediately. Contact HUR service: service@hur.fi

SEMIANNUALLY

Regular maintenance! The use of an authorized HUR service person is rec-ommended.

Basic condition check of device. Cleaning and lubrica-tion of piston rods. Lubrication and adjustment of roller cushions. Checking the compressor.

ANNUALLY

Regular maintenance! The use of an authorized HUR service person is rec-ommended.

Basic condition check of device. Cleaning and lubrica-tion of piston rods. Lubrication and adjustment of roller cushions. Checking the compressor.

WARNING! The safety level of the equipment can be maintained only if it is examined regularly for damage and wear, e.g. ropes, pulleys, connection points.

Detailed information regarding compressor and its maintenance can be found in the compressor manual. All mechanical devices need scheduled, routine maintenance. Proper maintenance will give many addi-

13 ver. 1/2017

tional service years for your HUR equipment. Note that ignoring maintenance might void warranty. For additional user safety and for keeping the product in trouble free condition, always instruct first-time users of the proper exercise methods and use of equipment. In case of any problems with your HUR product, please contact HUR service: service@hur.fi or +358-6-8325500 When reporting of the trouble the following information is required:

Model and serial number of the product

When the defect was detected

Description of the problem

Your contact information NOTE! The serial number can be found on the front side of the device frame in con-nection with the type plate. Notice that marking on the type plate can vary depending on device model. Basic things regarding to occurring problems: • In case of air leakage, turn off the compressor immediately to avoid overheating. Overheating can

cause more defects. • Apart from connecting the tubing, DO NOT try repairing anything before contacting HUR service. • Always switch off and disconnect any electronic supplies of the defective device. • Make sure that the defective device is not to be used before it is inspected and repaired properly. • All the tubing used in HUR machines are of “Quick Connect-type”. To connect, simply push the tube

inside the connector (Picture 1). To remove, push tube slightly in, press the locking ring on the con-nector and disconnect the tube (Picture 2).

Serial number

14 ver. 1/2017

4 SAFETY PRECAUTIONS AND WARNINGS

4.1 Safety precautions and warnings for users of HUR devices

• Do not adjust or use HUR equipment without the proper guidance of trained staff. • Before use, please carefully read warning signs, instructions for use and safety instructions that may be

attached to the device. • For safe operation of the equipment the safety zone is required: at least 0.5 meter on both sides of the

machine. Depending on the exercise the safety zone in front of the machine should be the length of pulley, the space user needs for exercising and added 0.5 meter.

• Before using the device, make sure that there are no other people or objects within the safety zone. • Always wear suitable sports shoes and clothing when using the equipment. • The use of equipment is prohibited under the influence of alcohol, drugs, medication or sedatives. • Stop exercising immediately if you experience nausea, dizziness or pain during your workout, and con-

sult your doctor. • Before you start exercising, check with your doctor the suitability of your workout for you, especially if

you have a pacemaker or if you have other physical disabilities. • Do not use damaged equipment. If the device is not working properly, do not attempt to repair it your-

self. Please inform the staff of the problem. • Improper use may result in personal injury or equipment damage, and removes all liability from the

manufacturer and will void the warranty. • These safety instructions and warnings are to be placed close to the equipment in a prominent loca-

tion. Safety instructions, warnings and possible dangers should be pointed out to each user of the equipment. The manufacturer has no responsibility for injury or damage caused to people or property.

• Exercising consumes energy and may cause sweating, so adequate nutrition and fluid intake prior to exercise is also important. Heavy meals consisting of ingredients that are hard to digest should be avoided.

• If the workout program includes strength training or other heavy exercises, it is advisable to carry out a proper warm up, e.g. on the exercise bike or treadmill.

• Cool-down exercises, muscle maintenance (stretching etc.), as well as fluid and nutritional balance maintenance are important actions after the workout. They prevent muscle pain and muscle stiffness.

• If you feel unusual pain after the workout, consult your doctor.

4.2 Safety precautions and warnings for owners of HUR devices

• Make sure to follow all the enclosed instructions how to install HUR Pulley. HUR is not responsible for

any accidents if the instructions are not followed. • Make sure that the hoses and cables are properly installed in such a way that no one can stumble on

them. • Do not allow anyone to adjust or control the HUR equipment without the proper guidance of trained

staff. • Make sure that the users carefully read warning signs, instructions for use and safety instructions that

may be attached to the device.

15 ver. 1/2017

• Inform users of the safety zone: at least 0.5 meter on both sides of the machine. Depending on the exercise the safety zone in front of the machine should be the length of pulley, the space user needs for exercising and added 0.5 meter.

• Make sure that before using the device users ensure that there are no other people or objects within the safety zone.

• Users should always wear suitable sports shoes and clothing while using the devices. • The use of equipment is prohibited under the influence of alcohol, drugs, medication or sedatives. • Make sure that the users stop exercising immediately if they feel nausea, dizziness or pain during the

workout, and advise them to contact their doctor immediately. • Users who have a pacemaker or other physical disabilities must obtain doctor’s permission before using

HUR equipment. • Do not use damaged equipment. The defective device must be removed from service immediately after

the defect has been detected. The device must be marked in such a way that its use is clearly prohibit-ed. If the device is not working properly, do not attempt to repair it yourself. Report the issue to HUR service, sevice@hur.fi or +358-6-8325500

• A device must be removed from service if the device warning labels have been damaged in such a way that they cannot be read.

• Be sure to read all warnings and cautions in the user instructions and the user and maintenance in-structions. Pay attention to all warnings, cautions and notes set out in the instructions.

• Improper use and failure of basic maintenance may result in user injury and equipment damage. In addition, these factors clear the manufacturer of all liability and will void the warranty.

• HUR safety instructions and warnings for users are to be placed close to the equipment in a prominent location. Safety instructions, warnings and possible dangers should be pointed out to each user of the equipment. The manufacturer has no responsibility for injury or damage caused to people or property.

16 ver. 1/2017

5 HUR PULLEY ACCESSORIES

Pulley Rowing Bench (8206)

With this bench Pulley can be used for even more exercises.

Straps and Grips:

17 ver. 1/2017

18 ver. 1/2017

6 WARRANTY TERMS OF HUR OY

These Warranty Terms of HUR Oy (hereinafter “HUR”) shall be applied to any device or accessory (hereinafter “Product”) manufac-tured by HUR. The purchaser of Product (hereinafter “Purchaser”) accepts these Warranty Terms and agrees to abide them by purchasing a Product from HUR. The Warranty will be void if the Purchaser does not comply with all the terms.

1 GENERALLY ABOUT THE PRODUCTS

All Products are developed and manufactured by HUR in Kokkola, Finland. HUR’s manufacturing process includes welding, painting, assembly, final inspection and packing. HUR’s quality control system is specially designed for the manufacturing process of fitness and rehab equipment and it is a part of HUR’s certified ISO 9001 Quality Management System. Despite continuous quality control, defects or malfunctions may occur in a single product or component.

2 WARRANTY

HUR warrants to the Purchaser that all Products are free from defects in material and workmanship for the Warranty Period as specified in the section 3. HUR will remedy all defects in material and workmanship of Products in accordance with these Warranty Terms. These Warranty Terms are the only warranty terms applicable for Products. These Warranty Terms are expressed in lieu of all other warranties or liabilities against defects or imperfections, hidden or otherwise, and any other obligation or liability arising on the basis of any kind of a defect in Products. The remedy subject to these Warranty Terms will be the sole, exclusive and only remedy available to the Purchaser. HUR will not in any case be liable for any other obligations or liabilities. HUR disclaims and ex-cludes all other expressed or implied warranties, including, any warranty of merchantability or fitness for a particular purpose.

3 WARRANTY PERIOD

HUR Products’ Warranty Periods are as follows: ten (10) years for the frame of the Product, three (3) years for all other Products excluding electronic components and upholstery, one (1) year for electronic components and three (3) months for upholstery (the applicable period hereinafter the “Warranty Period”). Warranty Period commences on the date when the Purchaser has purchased and received the product and approved the installation of the product by signing and dating the HUR Warranty Activation Form (hereinafter the “WAF”) and when WAF has been returned to HUR. Any repair or replacement on the basis of these Warranty Terms does not extend the Warranty Period. HUR’s liability on the basis of these Warranty Terms is limited to only such defects, which appear and are notified to HUR within the Warranty Period.

4 REMEDY

In the case of any defect covered by these Warranty Terms, HUR will remedy, repair or replace the defective Product, component or part of the Product, or at its discretion, refund the price of the defective Product to the Purchaser. A precondition for the reme-dy is that HUR’s examination shows the Product or the component or the part of the Product to be defective. Any replaced Product, component or part of the Product will become HUR’s property. Unless otherwise agreed, HUR will not be liable for any cost, expense, loss or damage whether direct or indirect and whether con-sequential or not. HUR does not have any responsibility regarding the suitability of the Product to any purpose of the Purchaser. Unless otherwise agreed, the Purchaser will bear the cost of repair work and any other costs incurred in connection with the repair, replacement, dismantling, installation and transportation of any Product, component or part. If the defective Product, component or a part of Product will be transported to HUR, by HUR’s will, for repair or replacement, HUR will also bear the cost and the risk of the transportation of the device from the Purchaser to HUR.

5 RESTRICTIONS

HUR’s obligations on the basis of these Warranty Terms apply only to defects occurring during the Warranty Period. The Product should have been used in its particular purpose, as expressed in User Manual. All instructions for use, installation and maintenance should be complied with. HUR’s obligations do not apply to normal wearing of parts in any Product, component or part of the Product; parts in need of rou-tine replacements or defects due to normal wear or deterioration. The warranty does not cover natural breakdown, normal wear and tear of parts and defects caused thereof. HUR’s obligations do not apply to any defects due to reasons out of HUR’s control, such as negligence or error in maintaining, handling or storing the Products; alteration or modification or addition to the Products without HUR’s prior written consent; failure to follow HUR’s instructions, wrong assembly, unsuitable use or unauthorized repairs or repairs carried out improperly. Warranty does not cover equipment damage caused by maintenance service non-authorized by HUR. Personal injury or damage caused to a person or another object is not covered by these Warranty Terms. Instructions for the

19 ver. 1/2017

installation and maintenance of the Products are available in the separate HUR technical manual. HUR equipment may only be installed by an authorized HUR installer. This limited Warranty is applicable only for the original Purchaser. The rights of Purchaser on the basis of these Warranty Terms cannot be transferred to any third party. The Purchaser shall return a duly filled file, WAF, to HUR in order to activate the Warranty within one (1) month since the date the Product was received. The Warranty is not applicable if WAF has not been duly filled and returned to HUR.

6 NOTIFICATIONS OF A DEFECT UNDER THIS WARRANTY

The Purchaser shall notify HUR in writing (HUR Claim Form recommended) of any defect covered by these Warranty Terms within two (2) weeks from the defect was detected. Such notifications are a precondition for any compensation and shall include at least the following details:

type and serial number of the defective Product;

date of the delivery of the Product to the Purchaser and the location of the Product;

information about the use of the Product;

detailed description of the defect. The Purchaser shall promptly provide any additional information concerning the defect and its occurrence that HUR may reasona-bly request. On receiving the Purchaser’s notification and the information referred above, HUR will remedy the Product, compo-nent or part. The Product, component or part shall, if so required by HUR, be returned to HUR for inspection together with the information referred above.

7 CONSUMER’S RIGHTS

A consumer can be entitled to legal rights in accordance with the applicable national legislation regarding consumer rights. Not-withstanding any provisions of these Warranty Terms, these Warranty Terms do not affect or prejudice the statutory rights of a consumer.

8 REVISIONS OF THE WARRANTY

HUR reserves the right to change these Warranty Terms at any time.

9 APPLICABLE LAW

These Warranty Terms shall be governed and interpreted in accordance with the laws of Finland. Any dispute arising shall be decid-ed by the courts of Finland. These Warranty Terms are valid from 1 January 2016.

Ab HUR OY

Patamäentie 4 67100 Kokkola

SUOMI – FINLAND Tel. +358 6 832 5500

Email: sales@hur.fi, service@hur.fi www.hur.fi