humbucker installation guide from neck - … for purchasing a tonerider humbucker. this guide...

Thanks for purchasing a Tonerider Humbucker. This guide provides wiring and installation information for all our four-conductor humbuckers. HUMBUCKER INSTALLATION GUIDE COIL SPLITTING: This wiring option leaves one coil on, making the pickup work like a true single coil. It is a useful modification to increase your tonal options. - SPLITTING TO THE SLUG COIL (Diagram 3): This is gives a fuller sound than the screw coil, especially in the bridge position. THE QUICK GUIDE: * Install with screw coils facing outwards. * Pressing the strings against the high frets, set the pickup heights to 3mm from the strings (neck) and 2mm (bridge). * The RED wire is “hot” and connects to the input lug of the volume pot or switch. * The GREEN wire and SHIELD are “ground” and connect to the back of a grounded pot. * The BLACK & WHITE wires should be soldered together. This is done at our workshop. * Test the guitar through an amplifier and make final adjustments to the height of the pickups. North/Slug Coil Start North/Slug Coil Finish South/Screw Coil Finish South/Screw Coil Start SOUTH NORTH POLARITY AND WIRING: FROM NECK PICKUP FROM BRIDGE PICKUP CONTACT US: Email: [email protected] Tel (UK): 01227 469414 Tel (Intl): +44 1227 469414 On the Web: www.tonerider.com - SPLITTING TO THE SCREW COIL (Diagram 4): Recommended for neck pickup only DPDT (on/on) “Hot” DPDT (on/on) “Hot” DPDT (on/on) “Hot” Ground SERIES & PARALLEL WIRING (Diagram 5): Parallel wiring gives a single coil-style tone with full humbucking operation. One DPDT switch is required for each humbucker to be wired in this way. Diagram 2 Diagram 3 Diagram 4 Diagram 5 “HOT”/ SIGNAL OUT GROUND 3-WAY TOGGLE SWITCH . We’ve included several common guitar wiring configurations; however if you need any extra information, don't hesitate to contact us. We are musicians at heart and no question is too large or too small. All Tonerider pickups have a limited lifetime warranty when purchased new. Please keep your receipt and see the enclosed warranty card for details.

Upload: vantruc

Post on 12-Apr-2018

220 views

Category:

Documents

1 download

Report

Download

Embed Size (px):

TRANSCRIPT

Thanks for purchasing a Tonerider Humbucker. This guide provides wiring and installation information for all our four-conductor humbuckers.

HUMBUCKERINSTALLATION GUIDE

COIL SPLITTING:This wiring option leaves one coil on, making the pickup work like a true single coil. It is a useful modification to increase your tonal options.

- SPLITTING TO THE SLUG COIL (Diagram 3): This is gives a fuller sound than the screw coil, especially in the bridge position.

THE QUICK GUIDE: * Install with screw coils facing outwards. * Pressing the strings against the high frets, set the pickup heights to 3mm from the strings (neck) and 2mm (bridge). * The RED wire is “hot” and connects to the input lug of the volume pot or switch. * The GREEN wire and SHIELD are “ground” and connect to the back of a grounded pot. * The BLACK & WHITE wires should be soldered together. This is done at our workshop. * Test the guitar through an amplifier and make final adjustments to the height of the pickups.

North/Slug Coil StartNorth/Slug Coil Finish

South/Screw Coil FinishSouth/Screw Coil Start

SOUTH

NORTH

POLARITY AND WIRING:

FROMNECK PICKUP

FROMBRIDGE PICKUP

- SPLITTING TO THE SCREW COIL (Diagram 4):Recommended for neck pickup only

DPDT (on/on)

“Hot”

DPDT (on/on)

“Hot”

DPDT (on/on)

“Hot” Ground

SERIES & PARALLEL WIRING (Diagram 5):Parallel wiring gives a single coil-style tone with full humbucking operation. One DPDT switch is required for each humbucker to be wired in this way.

Diagram 2

Diagram 3

Diagram 4

Diagram 5

“HOT”/SIGNAL OUT

GROUND

3-WAY TOGGLESWITCH

We’ve included several common guitar wiring configurations; however if you need any extra information, don't hesitate to contact us. We are musicians at heart and no question is too large or too small.

All Tonerider pickups have a limited lifetime warranty when purchased new. Please keep your receipt and see the enclosed warranty card for details.

2 HUMBUCKERS | 2 VOLUMES 2 TONES | 3 WAY TOGGLE · 2 HUMBUCKERS | 2 VOLUMES 2 TONES ... hurts our feelings if you use them in ... your guitar is a practically free way to get new

media.americanmusical.com · still combines the classic electric guitar tone of powerful humbuckers with the acoustic-like NanoMagTM low-impedance pickup system mounted to a strategically

guitarinside.com · Duncan TB—4 Ano SH-2 HumBucKERS, EBOnY FinGERBOARD WiTH m0THER OF PEARL SHARKFin ir1LAY, An ORiGinAL ROSE TRErn0L0 manuFac-ruRED BY SCHALLER. THE RRs is THE

Barclay James Harvest · 2019. 1. 6. · Gold Fender Stratocaster Sunburst Fender Stratocaster with Alembic electronics Blonde Fender Stratocaster with 2 Gibson Humbuckers Gibson

2 SINGLE COILS | 1 HUMBUCKER 1 VOLUME | 2 TONE | 5 WAY … · Solder.047 cap Solder Seymour Duncan Tip (hot output) Sleeve (ground). The inner, circular portion of the jack Output

HH: 2 Humbuckers Overview

contents · PDF filecontents About the Author ... The Michael Angelo Batio Sound..... 120 ... Guitar electronics can range from the very simple single humbucker, single volume knob

· 25.5" scale length shred machine ... Total access lower cutaway ... Special made DiMarzio humbuckers Satin nickel hardware

Mini Rail Humbucker Dimensions STANDARD · 2018. 9. 7. · Fokin Pickups 2018 [email protected] Mini Rail Humbucker Dimensions STANDARD SLIM 83,4 77 69,2 18 23,6 83,4 77 69,2

John Myung Model · Dream Theater fame. A layer of figured maple veneer, 6-string neck with double truss rods and infinity inlay, solid brass bridge, two Alnico humbuckers and active

BUSUYI GUITAR LLC 2100 RIVERSIDE PKWY STE 128 ... · 2 Guitars in 1 Double Neck, Double Sides Busuyi Venum 2 Magnet humbucker pickups Dual Jack, Dual Control Rosewood fretboard with