hp0-055 2-2
DESCRIPTION
55TRANSCRIPT
HP0-055Implementing HP ProLiant ServersVersion 2.2Table of contents
4Topic 1, Main (158 Questions)
Total number of questions: 435Topic 1, Main (158 Questions)
QUESTION NO: 1
You need a storage solution with both SCSI-based and ATA-based drives in a two-tier data protection model. Which HP StorageWorks solutions meet this requirement? Select THREE.
A. MSA500
B. MSA1000
C. MSA20
D. MSA30
E. MSA1500cs
Answer: C,D,E
QUESTION NO: 2
Which level of access is needed to clear the Version Control Repository log?
A. Guest
B. User
C. Operator
D. Owner
Answer: C
QUESTION NO: 3
Which software solution can create virtual servers running multiple operating systems on HP ProLiant platforms?
A. nPar for ProLiant Server
B. Virtual Platform for ProLiant Server
C. Microsoft Virtual Server
D. vPar for ProLiant Server
Answer: C
QUESTION NO: 4
Which type of solutions can reduce the risk factor and financial losses caused by x86 infrastructure failure in a Small and Medium Business (SMB)? Select THREE.
A. hot-swap processors
B. high availability clustering
C. proper data protection on tape
D. data replication offsite
E. smart aware architecture
Answer: B,C,D
QUESTION NO: 5
What is the correct way to install Red Hat Enterprise Linux 3.0 on a ProLiant DL380 G4?
A. Use the assisted installation option of SmartStart.
B. Download the server's specific drivers to the etc\OEMdrivers folder before starting a manual installation.
C. Use the vendor-supplied operating system media to begin the manual installation process.
D. Create a driver diskette to be used with a SmartStart manual installation.
Answer: C
QUESTION NO: 6
When monitoring from an HP Systems Insight Manager (HP SIM) server, you notice that all SNMP traps from the mail server are received twice. What could be the reason?
A. There are 2 community strings created on the mail server.
B. The mail server is discovered twice in HP SIM.
C. There are 2 versions of management agents running on the mail server.
D. The RILOE II board in the mail server is set to forward traps to HP SIM as well.
Answer: D
QUESTION NO: 7
Which RAID level does the SmartArray controller configure by default when 6 hard drives are installed?
A. RAID 1+0
B. RAID 0
C. RAID 6 (ADG)
D. RAID 5
Answer: D
QUESTION NO: 8
When setting up a data center, how would you install an HP Modular Cooling System? Select TWO.
A. as an option inside an existing HP 10000 G2 series rack
B. as an option inside a new HP 5000 series rack
C. in a datacenter with at least 59" (150cm) clearance around the rack
D. adjacent to any third party rack
E. as a stand alone solution
Answer: D,E
QUESTION NO: 9
Which online utility changes the cache read/write ratio settings on a SmartArray 6404 controller?
A. Array Diagnostic Utility (ADU)
B. Array Configuration Utility (ACU)
C. Array Management Utility (AMU)
D. Options ROM Configuration for Arrays (ORCA)
Answer: B
QUESTION NO: 10
Your customer complains that even during idle time the server Ultra320 SCSI hard drives are working. They are worried that it may cause performance problems. What will you tell this customer?
A. The hard drive activity is caused by the Dynamic Sector Repair feature and it has no impact on performance.
B. The hard drive activity is caused by the internal backup process of RAID configuration and the impact on performance is minimal.
C. The server has postponed writes from previous day which causes hard drive activity and huge impact on performance.
D. The server is performing Drive Protection System tests and, depending on drive speed and type, the impact on performance might be huge.
Answer: A
QUESTION NO: 11
Which ProLiant servers are covered by HP pre-failure warranty? Select TWO.
A. DL380
B. DL580
C. ML150
D. DL145
Answer: A,B
QUESTION NO: 12
Where do you install the ProLiant Support Pack when using the Linux Deployment Utility?
A. on all Linux servers on the network
B. on all servers on the same subnet
C. on both local and remote Linux servers
D. only on the local server
Answer: D
QUESTION NO: 13
Which components are installed when you remotely deploy the HP ProLiant Support Pack from the HP SmartStart CD? Select THREE.
A. WBEM agent for operating system
B. HP Systems Insight Manager
C. System Management Homepage
D. Insight Management Agents
E. HP Instant Support Enterprise Edition
F. Adapters drivers and utilities
Answer: C,D,F
QUESTION NO: 14
Which operating system is required to configure Microsoft Cluster Services (MSCS) solutions?
A. Microsoft Windows 2003 SBS Edition
B. Microsoft Windows 2003 Web Edition
C. Microsoft Windows 2003 Enterprise Edition
D. Microsoft Windows 2003 Standard Edition
Answer: C
QUESTION NO: 15
What provides Windows support to WBEM applications?
A. Tomcat web server
B. OpenSSH
C. WBEM service layer
D. WMI Mapper
Answer: D
QUESTION NO: 16
Where can the installation files for Version Control Agent be found? Select TWO.
A. Firmware Maintenance CD
B. HP website
C. SmartStart CD
D. Version Control Agent Media CD
E. Windows Installation CD
Answer: B,C
QUESTION NO: 17
Which tool can be used to migrate from RAID 1 to RAID 5 in a Linux environment with the Smart Array controller?
A. Array Configuration Utility (ACU)
B. Option ROM Configuration for Arrays (ORCA)
C. Array Manipulation Utility (AMU)
D. Array Diagnostic Utility (ADU)
Answer: A
QUESTION NO: 18
How would you grant access to your colleague for the System Management Homepage (SMH)?
A. create a username and password in the security tab of the SMH
B. add his domain username to the correct user group in the settings tab
C. add his username to the HP Systems Insight Manager (HP SIM) database
D. share with your colleague the default username and password for the SMH
Answer: B
QUESTION NO: 19
Your customer is looking for an ultra dense High Performance Cluster. Which ProLiant family should the cluster be based on?
A. ML
B. DL
C. CL
D. BL
Answer: D
QUESTION NO: 20
Which tool allows you to manage HP SmartArray Controllers and HP StorageWorks MSA500?
A. CommandView MSA
B. Array Configuration Utility
C. SmartArray Manager
D. CommandView SA
Answer: B
QUESTION NO: 21
Your customer is looking for an ultra dense High Performance Cluster. Which ProLiant family should the cluster be based on?
A. DL
B. BL
C. CL
D. ML
Answer: B
QUESTION NO: 22
Which tool is used to compare different server configuration snapshots?
A. Inspect utility
B. Insight Diagnostics Online edition
C. Insight Diagnostics Offline edition
D. Integrated Management Log viewer
Answer: B
QUESTION NO: 23
You want to install an HP StorageWorks DAT72 drive into the internal media bay of an HP ProLiant ML370. Which feature is now available to the customer if an operating system disaster happens?
A. One Button Disaster Recovery
B. Snapshot backup and restore
C. Fast Recovery option
D. Zero Downtime Backup and Restore
Answer: A
QUESTION NO: 24
Which remote management capability is available in the HP ProLiant series to enable customers to access, control and troubleshoot server hardware?
A. Windows Management Interface
B. Web-based Enterprise Management
C. Remote KVM switch
D. Integrated Lights Out (iLO) or iLO 2
Answer: D
QUESTION NO: 25
What differentiates the HP BladeSystem from HP ProLiant DL-series servers?
A. easier deployment with a higher cost for management
B. distributed infrastructure architecture
C. consolidation of processors and memory for a scalable SMP system
D. consolidation of power, cooling, network and management
Answer: D
QUESTION NO: 26
The administrator of HP Systems Insight Manager (HP SIM) informs you that no traps arrived into HP SIM after installing HP Management Agents on your new ProLiant DL380 G4 running SuSE Linux. Why didn't the traps arrive into HP SIM? Select TWO.
A. The version of the Management Agents you installed do not match the HP SIM version.
B. The HP SIM server is not licensed to receive traps from SuSE Linux servers.
C. The SNMP community name is not configured.
D. The trap destination is set incorrectly.
E. The ProLiant server is configured with a DHCP address.
Answer: C,D
QUESTION NO: 27
Your customer is exploring if their existing HP ProLiant DL585 is capable of handling 2 critical applications that need to be consolidated. Service level and performance are critical for these 2 applications. Which tools can you use to determine if this is possible? Select THREE.
A. Systems Insight Manager (SIM)
B. Workload Management Pack (WMP)
C. Performance Management Pack (PMP)
D. Insight Remote Agent (IRA)
E. Version Control Agent (VCA)
Answer: A,B,C
QUESTION NO: 28
When using the Performance Management Pack, you found the ProLiant DL580 server is running slowly with high paging. What should you do to resolve the problem?
A. Increase more processors.
B. Add more hard drives and migrate the RAID level.
C. Increase the amount of memory.
D. Add another SmartArray controller.
Answer: C
QUESTION NO: 29
What is HP IP Console Viewer used for?
A. take over and control the graphical console of iLO2 card
B. configure the IP address of HP Systems Insight Manager and remote access cards
C. configure remote access to System Management Homepage, iLO and iLO2 cards
D. configure interface adapters and cascaded legacy KVM console switches
Answer: D
QUESTION NO: 30
Which tool should you use to fully document the installed configuration of your ProLiant server?
A. ROM Based Setup Utility (RBSU)
B. Insight Diagnostics Online Edition
C. Inspect Utility
D. Array Diagnostics Utility (ADU)
Answer: B
QUESTION NO: 31
Which add-on to HP Systems Insight Manager provides the ability to detect, analyze and explain system performance bottlenecks?
A. Performance Management Pack
B. Workload Management Pack
C. Systems Insight Diagnostics
D. System Monitor
Answer: A
QUESTION NO: 32
Your customer is planning to implement a Microsoft Windows Cluster Solution using HP ProLiant DL380 servers. You do not have the knowledge to size and build the list of components for a supported configuration. What can you use?
A. HP Smart Setup Utility Cluster Edition
B. HP Product Bulletin with Internet Pricing Quoter
C. HP ProLiant DL380 Cluster Package
D. HP Enterprise Cluster Configurator
Answer: C
QUESTION NO: 33
Your customer knows that he will need a blade enclosure for the HP BladeSystem infrastructure. What else is necessary? Select TWO.
A. power infrastructure
B. modular cooling system
C. external storage system
D. interconnect option
Answer: A,D
QUESTION NO: 34
Which settings provide secure access to the HP System Management Homepage from the management LAN? Select TWO.
A. Public and Private Key
B. IP Binding List
C. Local SSL certificate
D. IP Access Restriction
E. Public SSL certificate
Answer: B,D
QUESTION NO: 35
Which product provides the tools needed to receive proactive notification of potential bottleneck conditions and debug existing performance issues?
A. Workload Management Pack
B. HP Insight Diagnostics
C. Performance Management Pack
D. Vulnerability and Patch Management Pack
Answer: C
QUESTION NO: 36
You want to connect an HP StorageWorks MSA20 enclosure directly to your HP ProLiant DL385 system. Which SmartArray controller do you need?
A. SmartArray 5i Plus
B. SmartArray 641
C. SATA RAID Controller
D. SmartArray 6404
Answer: D
QUESTION NO: 37
After an array expansion you discover some problems with the storage subsystem. Which HP tool diagnoses the Smart Array controller and all disks connected to it?
A. ROM Based Setup Utility (RBSU)
B. Array Configuration Utility (ACU)
C. Array Diagnostic Utility (ADU)
D. Option ROM Configuration for Arrays (ORCA)
Answer: C
QUESTION NO: 38
Where can you check the system ROM version of a ProLiant DL580 G3, prior to upgrading to the latest version?
A. ROM Based Setup Utility (RBSU)
B. Management Processor (MP)
C. Server Configuration Utility (SCU)
D. Option ROM Configuration for Arrays (ORCA)
Answer: A
QUESTION NO: 39
Which utilities can be used to identify an outdated firmware version of a SmartArray controller? Select TWO.
A. Array Configuration Utility
B. System Erase Utility
C. Array Diagnostics Utility
D. System Management Homepage
E. Integrated Management Log
Answer: A,C
QUESTION NO: 40
Which ProLiant Essentials Pack gathers utilization statistics to support your recommendation for additional processors?
A. Vulnerability and Patch Management Pack
B. Rapid Deployment Pack
C. iLO Advanced Pack
D. Performance Management Pack
Answer: D
QUESTION NO: 41 DRAG DROP
You are designing a server-storage solution using a single SmartArray 6404 in a ProLiant DL380 G4. The customer wants the highest availability, performance and protection against single SCSI bus failure; with utilization of total raw capacity above 70%.
Logical Volume: C:\ for Windows OS - Size: 20GB usable capacity on RAID 1+0 on internal storage
Logical Volume: D:\ for DVD-ROM
Logical Volume: E:\ for swapfile (pagefile.sys) - Size: 32GB usable capacity on RAID 1+0 on internal storage
Logical Volume: F:\ for applications program - Size: 35GB usable capacity on RAID ADG
Logical Volume: G:\ for application data - Size: 350GB usable capacity on RAID 1+0
Using drag and drop, match the correct types of RPM and capacity with the internal and external storage locations for the above scenario.
Answer: Explanation:
QUESTION NO: 42
Which tool should you use to deploy a new version of a ProLiant Support Pack (PSP) to a server that can only be rebooted during a scheduled maintenance period?
A. Remote Deployment Utility (RDU)
B. Remote Batch Utility (RBU)
C. Platform Administration Tool (PAT)
D. Pre-operating system eXEcution (PXE)
Answer: A
QUESTION NO: 43 DRAG DROP
HP developed a six-step troubleshooting methodology.
Place the steps in the correct order.
Answer: Explanation:
QUESTION NO: 44
A Site Survey is useful to determine which options? Select TWO.
A. the load placed on the current electrical system
B. the type of disk storage needed in the server
C. the Operating System to be installed on the Server
D. the memory requirements of the server
E. the location of where the server will be installed
Answer: A,E
QUESTION NO: 45
Which feature differentiates the HP SmartArray 6404 from the HP SmartArray 6i on a HP ProLiant DL380?
A. Online migration
B. Online expansion
C. RAID 1+0
D. RAID 6 (ADG)
Answer: D
QUESTION NO: 46
Which tools can be used to set a SmartArray controller as a bootable controller? Select TWO.
A. Array Configuration Utility (ACU)
B. Option ROM Configuration for Arrays (ORCA)
C. ROM Based Setup Utilities (RBSU)
D. Array Diagnostic Utility (ADU)
E. Server Configuration Utility (SCU)
Answer: B,C
QUESTION NO: 47
When should you perform data collection to establish a performance baseline?
A. during normal server operation
B. after normal operational hours
C. during peak server utilization
D. before the initial installation of the equipment.
Answer: A
QUESTION NO: 48
Why would the Inspect Utility be unavailable when accessing the System Maintenance Menu on ProLiant DL380 G3?
A. You are not logged in as an administrator for that system.
B. You have not installed the Inspect Utility Option pack.
C. Your ProLiant server has a 2MB ROM.
D. You entered the basic mode of the System Maintenance Menu.
Answer: C
QUESTION NO: 49
Which type of secure access should you use to prevent unauthorized network users from accessing the HP System Management Homepage (SMH)?
A. WMI access
B. WBEM access
C. IP range access
D. SSL encryption
Answer: C
QUESTION NO: 50
When should you establish a new performance baseline for a server?
A. when the hardware configuration has changed
B. each time the server is rebooted
C. after replacement of a failed component
D. when a new user is added to the environment
Answer: A
QUESTION NO: 51
What is the best way to install all the required management agents and supported drivers on your ProLiant server?
A. Call HP Competency Center for instructions on how to solve this problem.
B. Locate the latest ProLiant Support Pack on the HP website, then download and install it.
C. Locate all missing components on the HP website; download and install them manually.
D. Use System Software Manager to download and install all needed software and drivers.
Answer: B
QUESTION NO: 52
Why should you install Version Control Repository Manager (VCRM) before configuring the Version Control Agent (VCA) on your managed server?
A. You can only configure VCA when both VCA and VCRM are installed on the same managed server.
B. The VCA service will not start if there is no VCRM server detected in the network.
C. A VCRM server must exist in the network so VCA can update the information.
D. The VCA installation program will not run if the VCRM service is not present.
Answer: C
QUESTION NO: 53
Which tool should you use to predict multiple drive faults within your ProLiant server's logical drive?
A. Insight Diagnostics Offline edition
B. HP Insight Remote agents
C. Insight Diagnostics Online edition
D. Array Configuration Utility
Answer: C
QUESTION NO: 54
Which component is required in an HP Rack to control the power source to each ProLiant server by segmenting them to a smaller section? For example, you have 40 units of DL145 in a 42U rack, segmenting them into a smaller segment of 6-8 servers each.
A. Power Distribution Unit (PDU) Management Module
B. Earth Leakage Circuit Breaker (ELCB)
C. Easy Access Button (EAB) software
D. Power Distribution Module (PDM)
Answer: D
QUESTION NO: 55
Which TCP port is used as the default port to access the System Management Homepage?
A. 50000
B. 3257
C. 80
D. 2381
Answer: D
QUESTION NO: 56
You have just added an HP RILOE II remote management adapter into the ML350 server. What must you change in order to enable it to integrate into Microsoft Windows Server 2003?
A. Configure SNMP community name on SNMP services on Windows.
B. Install Remote IPMI Agent on Microsoft Networking services in Windows Control Panel.
C. Remove Remote WMI support on Microsoft Windows operating system.
D. Activate Remote Insight Information Agent under HP Management Agents in Windows Control Panel.
Answer: D
QUESTION NO: 57
Which feature in HP Systems Insight Manager (HP SIM) will allow you to update multiple servers with Version Control Agent (VCA) settings?
A. Changing Agent Settings
B. Update Software Settings
C. Overall Software Status
D. Replicate Agent Settings
Answer: D
QUESTION NO: 58
Where can you configure advanced memory protection on a ProLiant DL380 G4?
A. on the system board's maintenance switch
B. in the ROM-based Setup Utility (RBSU)
C. in the Advanced Options of the System Configuration Utility
D. in the System Maintenance menu
Answer: B
QUESTION NO: 59
You have to configure a Smart Array controller in a server that is located 300 km away from your office. Which tools can be used for remote configuration of this controller? Select TWO.
A. Graphical console from iLO
B. Flexible Array Storage Tool via Systems Management Homepage
C. Remote Array Configuration Toolkit via System Management Homepage
D. Remote Deployment and Configuration Utility
E. Array Configuration Utility via Systems Management Homepage
Answer: A,E
QUESTION NO: 60
Which databases can be used on a Windows-based HP Systems Insight Manager (HP SIM) server? Select TWO.
A. Oracle 9i release 2
B. MSDE 2000
C. OpenSSH
D. Access Enterprise Edition
E. PostgreSQL 7.4.0
Answer: A,B
QUESTION NO: 61
Your customer wants to implement a storage solution where disk performance is as important as data availability. Which RAID level should you recommend?
A. RAID 6 (ADG)
B. RAID 0
C. RAID 5
D. RAID 1+0
Answer: D
QUESTION NO: 62
Which HP Premium Software/Hardware support Care Pack provides on-site hardware support and over-the-phone software support; 13 hours per day and 5 days per week?
A. Support Plus 24
B. Support Plus
C. Critical Service
D. Proactive 24
Answer: B
QUESTION NO: 63
You need to deploy an array set with 2 logical volumes across a total of 35 disk drives using MSA30 storage enclosures. Which HP SmartArray controller would you use to support the array set with maximum protection?
A. SmartArray P600
B. SmartArray 642
C. SmartArray 6404
D. SmartArray 6402
Answer: C
QUESTION NO: 64
Which features does HP Intelligent Networking Pack provide? Select TWO.
A. Automatic Virus cleaning
B. Fast Path failover
C. Fabric Tree support
D. Dual Channel teaming
E. Fast EthernetChannel
Answer: B,D
QUESTION NO: 65
Which RAID level would you suggest when I/O performance and fault tolerance are very important?
A. RAID 5
B. RAID 0
C. RAID 1+0
D. RAID 6 (ADG)
Answer: C
QUESTION NO: 66
When setting up disks on a SmartArray controller, when should you change the default stripe size setting to a larger value? Select TWO.
A. when the application is performing an equal number of reads and writes
B. when the application is primarily writing to disk on RAID 5
C. when the application is performing random read/write to disk
D. when the application is primarily writing to disk on RAID 1+0
E. when the application is primarily performing sequential reads
Answer: D,E
QUESTION NO: 67
How do you configure Online Spare Memory in the ProLiant 300 series?
A. by setting the correct switch on the system board
B. by installing the correct driver from the ProLiant Support Pack
C. by entering the license key for Online Spare Memory in RBSU
D. by enabling the option in the ROM Based Setup Utility (RBSU)
Answer: D
QUESTION NO: 68
You want to add an external storage enclosure to your ProLiant ML370 and there is only 1U of space available in your rack. Which enclosure would you select?
A. MSA50
B. MSA500
C. MSA30
D. MSA20
Answer: A
QUESTION NO: 69
What are the advantages of software-based RAID over hardware-based RAID? Select TWO.
A. lower cost to deploy
B. support for online spare drives
C. better performance
D. the ability to span multiple host controllers (duplexing)
E. faster and more reliable
Answer: A,D
QUESTION NO: 70
The System Management Homepage uses which type of user interface?
A. web-based
B. console
C. serial
D. command line
Answer: A
QUESTION NO: 71
You are not able to modify the thresholds on the file system space used on your ProLiant server using the HP Insight Management agents. The server is running Windows 2003. What could be the cause?
A. The SNMP community is set to READ only.
B. The management agent account is not linked to the administrative account of the OS.
C. The file system is created on dynamic disks.
D. The management agents are configured as READ only.
Answer: A
QUESTION NO: 72
Which tool identifies the reason for a bottleneck on a ProLiant DL385?
A. Intelligent Networking Pack (INP)
B. Essentials Workload Management Pack (WMP)
C. Performance Management Pack (PMP)
D. Insight Diagnostics Survey Utility (IDSU)
Answer: C
QUESTION NO: 73
Which Linux tools are used to collect system performance data?
A. pingstat and memcat
B. var and pingstat
C. iostat and grep
D. iostat and vmstat
Answer: D
QUESTION NO: 74
You want to allow only a single IP address to access the System Management Homepage. Which option must you enable and configure?
A. IP Restricted Logins
B. Trust Mode
C. Trusted Management Server
D. IP Binding
Answer: A
QUESTION NO: 75
You have to prepare a backup solution for your customer. Which HP sizing tool is used to select the best backup solution for a given environment?
A. Enterprise Backup Config Tool
B. StorageWorks Backup Sizing Tool
C. HP Backup Solution Sizer
D. Backup Configurator for SMB
Answer: B
QUESTION NO: 76
Your customer bought two new hard drives to expand the existing array on his ProLiant server with a Smart Array controller. Which HP tool accomplishes this task?
A. Array Configuration Utility (ACU)
B. Array Diagnostic Utility (ADU)
C. ROM Based Setup Utility (RBSU)
D. Option ROM Configuration for Arrays (ORCA)
Answer: A
QUESTION NO: 77
You execute Insight Diagnostic Online Edition to diagnose your logical volume. You see the icon in the diagnostic results. What does this indicate?
A. disk drive was put in a fault mode due to communications problems unrelated to the health of the disk
B. disk drive was put in a fault mode but was unable to verify the drive details needed for replacement
C. unable to test the disk drive due to a communications problem unrelated to the health of the disk
D. unable to test the disk drive because no online spare drive was available
Answer: A
QUESTION NO: 78
How can you update the firmware on a ProLiant server without physical access to the server? Select TWO.
A. Microsoft Remote Installer with ProLiant option
B. Remote Firmware Installer with Command Line Interface support
C. Remote Flash Downloader
D. Version Control Repository Manager (VCRM) with Version Control Agent (VCA)
E. iLO with Advanced Pack
Answer: D,E
QUESTION NO: 79
What should you do FIRST before installing an operating system on a ProLiant series server?
A. select the correct boot order
B. select the correct Operating System in the ROM Based Setup Utility (RBSU)
C. update the system and option ROMs
D. create a logical drive on the array controller
Answer: C
QUESTION NO: 80
What is the best location to install a R3000XR UPS in a rack?
A. below the keyboard drawer for easier access
B. in the rack, at the top to save space for heat dissipation
C. the bottom of the rack for more stability
D. above the keyboard drawer for easier cable installation
Answer: C
QUESTION NO: 81
You need to deploy a solution that will enable you to proactively monitor and receive failure alerts through email for 45 ProLiant servers, 15 Modular Smart Array's and a few HP LaserJet network printers. Which software components enable you to do this? Select THREE.
A. HP Workload Management Pack
B. HP ProLiant Support Pack
C. HP GlancePlus Pack for Windows
D. SMTP Mail Server
E. HP Systems Insight Manager
Answer: B,D,E
QUESTION NO: 82
An IT administrator is considering using Instant Support Enterprise Edition (ISEE). What are some features of ISEE? Select THREE.
A. continuous event monitoring
B. remote diagnostic and troubleshooting
C. forwarding alerts to multiple HP SIM servers
D. automatic download of patches from HP website
E. automated event notification to HP
Answer: A,B,E
QUESTION NO: 83
Your customer is looking for an economic backup solution. They currently have 6GB of data and data growth is about 1% per year. Which technology should you recommend to this customer?
A. SDLT
B. DAT
C. AIT
D. LTO
Answer: B
QUESTION NO: 84
Your customer bought a new DL580 ProLiant server. What is the standard warranty for this server?
A. 1-0-0
B. 1-1-1
C. 3-3-3
D. 3-1-1
Answer: C
QUESTION NO: 85
How can you verify a processor upgrade is functional on a ProLiant BL p-series server before you return it to service?
A. Use Rapid Deployment Pack.
B. Use the blade diagnostics station.
C. Use the System Management Homepage.
D. Use HP Insight Diagnostics Offline Edition.
Answer: B
QUESTION NO: 86
Your customer is looking for a shared storage solution that supports up to four different servers. Two servers are clustered and two are standalone servers. What is the best solution for this customer?
A. MSA20
B. MSA30
C. MSA500 G2
D. MSA50
Answer: C
QUESTION NO: 87
What should you do if you want to attach 20 small form factor (SFF) SAS or SATA drives to your ProLiant DL380?
A. cascade two MSA50
B. cascade two MSA20
C. cascade two MSA30
D. cascade one MSA20 and one MSA50
Answer: A
QUESTION NO: 88
Which tool helps to isolate a performance bottleneck in the network subsystem on a Microsoft Windows Server?
A. System Monitor
B. mpstat
C. System Management Homepage
D. iostat
Answer: A
QUESTION NO: 89
A ProLiant server locks up and restarts frequently. What should you do before replacing any parts?
A. Update the system and options ROM.
B. Restore the last known good backup.
C. Disable ASR in the ROM Based Setup Utility (RBSU).
D. Re-install the server's operating system.
Answer: A
QUESTION NO: 90
How does HP Systems Insight Manager receive detailed event messages about MSA storage devices? Select TWO.
A. Fibre Channel signaling
B. PPP communications
C. SMTP messaging
D. SNMP traps
E. WBEM events
Answer: D,E
QUESTION NO: 91
Which level of indication in the Version Control Agent (VCA) log file shows that a feature of VCA might be incorrectly configured?
A. Major
B. Warning
C. Informational
D. Normal
Answer: B
QUESTION NO: 92
The operating system utilization monitor indicates that there is high utilization on the system processor. Which action should you take next?
A. Remove any unnecessary applications.
B. Upgrade to a faster processor.
C. Add a second processor to balance the CPU utilization on the ProLiant server.
D. Use Performance Management Pack (PMP) to check memory and network utilization.
Answer: D
QUESTION NO: 93
Which utility is used to download new drivers, firmware and ProLiant Support Pack from the Internet?
A. HP Insight Softpaq Manager
B. HP System Management Homepage
C. Version Control Repository Manager
D. HP ProLiant Insight Downloader
Answer: C
QUESTION NO: 94
Your customer is looking for a ProLiant server to run Microsoft SQL Server. Which HP tool can be used to select the best hardware platform for this application?
A. Microsoft SQL Configurator
B. HP Best Practices and Solution website
C. Solution Sizer from ActiveAnswers
D. HP Enterprise Configurator for Microsoft Products
Answer: C
QUESTION NO: 95
You added a new Battery Backed Write Cache to an existing Smart Array controller and need to migrate the RAID level. Why does the RAID migration not start?
A. the Smart Array controller does not have the migration feature enabled
B. rebuild priority is set to low in the Smart Array controller.
C. 100% of cache is set to be "read cache"
D. the battery in the Smart Array controller is not fully charged
Answer: D
QUESTION NO: 96
Where do you set thresholds on the file system space used on a ProLiant server running Windows 2003, that sends warnings to HP Systems Insight Manager (HP SIM)?
A. in Quota Manager of the operating system
B. in the storage section of the HP Insight Management agents
C. in HP SIM - Thresholds option of the Configure tab
D. in Control Panel - HP Management Agents of the operating system
Answer: B
QUESTION NO: 97
You have added new drives to an existing Smart Array controller, but the controller does not recognize them. What should you do first to solve this problem?
A. Replace hard drives.
B. Run Option ROM Configuration for Arrays (ORCA) to bring the drives online.
C. Run Array Diagnostic Utility to bring the drives online.
D. Flash the firmware of the controller and hard drives to the latest version.
Answer: D
QUESTION NO: 98
Which utility is installed, as part of HP ProLiant Support Pack, to manage the internal storage array controller?
A. LightPath Utility (LPutilNT)
B. Option-ROM Configuration for Array (ORCA)
C. Array Configuration Utility (ACU)
D. ROM-Based Setup Utility (RBSU)
Answer: C
QUESTION NO: 99
Which online utility can you use to check the rebuilding status of a degraded array set?
A. Optional ROM Configuration for Arrays
B. iostat command
C. Array Configuration Utility
D. Array Diagnostics Utility
Answer: C
QUESTION NO: 100
Which utility determines that drives are installed in the wrong order on an array?
A. Storage Management Utility (SMU)
B. Array Configuration Utility (ACU)
C. Array Diagnostic Utility (ADU)
D. System Configuration Utility (SCU)
Answer: C
QUESTION NO: 101
What is the difference between a normal backup and a copy backup?
A. copy backup is much faster than normal backup
B. normal backup is much faster than copy backup
C. normal backup resets the archive bit
D. copy backup resets the archive bit
Answer: C
QUESTION NO: 102
Which components are covered by HP prefailure warranty? Select THREE.
A. processor
B. chipset
C. IO controller
D. memory
E. hard disk drive
Answer: A,D,E
QUESTION NO: 103
What type of remote management capability is offered as an add-on to the HP ProLiant DL-series and BL-series servers?
A. RILOE II with only DHCP support license
B. Standard iLO
C. RILOE II Advanced Pack license
D. iLO Advanced Pack license
Answer: D
QUESTION NO: 104
Your customer wants to utilize his existing SCSI drives and IP network infrastructure to implement a small SAN. Which storage solution would you recommend?
A. MSA1000
B. MSA 30
C. MSA1510i
D. MSA1500cs
Answer: C
QUESTION NO: 105
What information is saved in the Integrated Management Log (IML)?
A. installed firmware
B. memory configuration
C. network link status
D. raid configuration
Answer: C
QUESTION NO: 106
Which HP software solution is used to find potential security problems within Windows or Linux operating systems and applies the appropriate hot-fixes from the operating system vendor?
A. Vulnerability and Patch Management Pack
B. Patch and Hotfix Manager for Windows or Linux
C. System Security Manager for Windows/Linux
D. Harris Security Scanner Enterprise Edition
Answer: A
QUESTION NO: 107
Where can Hyper-Threading be disabled on a ProLiant server?
A. in the System Maintenance Menu
B. on the system board's maintenance switch
C. in Computer Management on a ProLiant running Windows
D. in the Advanced Options menu of the RBSU
Answer: D
QUESTION NO: 108
What type of hard drive would you select if cost and capacity are important?
A. Serial ATA (SATA)
B. Serial Attached SCSI (SAS)
C. Parallel SCSI
D. Parallel ATA (PATA)
Answer: A
QUESTION NO: 109
Which HP tool assists with facility planning and can calculate the power and heat load per rack?
A. HP Rack Configurator Online
B. HP Power and UPS Sizer
C. HP Facility Design Reference Guide
D. HP Rack/Site Preparation Utility
Answer: D
QUESTION NO: 110
Which HP server management product ships with all HP ProLiant 300 and 500 series servers?
A. Workload Management Pack
B. iLO Advanced Pack
C. Virtualization Manager
D. Systems Insight Manager
Answer: D
QUESTION NO: 111
Where in the system status screen are the Integrated Lights-Out (iLO) self-test results displayed?
A. Integrated Management Log Screen
B. iLO Event Log Screen
C. Server Status Screen
D. Server and iLO Diagnostics Screen
Answer: D
QUESTION NO: 112
Your customer has a ProLiant DL380 G4 server that is sharing files for five departments in his company. Most read and writes are random. What can he do to improve the performance on this system?
A. Install more disk drive cache for read operations.
B. Install the Battery-Backed Write Cache (BBWC) option.
C. Create a separate logical drive for each department.
D. Turn off caching for small files.
Answer: B
QUESTION NO: 113
You are at a customer's site to upgrade the processors in a ProLiant server. What should you do prior to adding the new processor?
A. Upgrade system firmware to the latest version.
B. Upgrade the processor board firmware.
C. Disconnect the external storage system before adding the processor.
D. Install cache coherency filters.
Answer: A
QUESTION NO: 114
Prior to installing the Fibre Channel Adapter (FCA) into the ProLiant server, what should you gather from the adapter in order to simplify the installation and security implementation for the SAN environment?
A. FCA chipset
B. ALPA address
C. World-wide name (WWN)
D. adapter serial number
Answer: C
QUESTION NO: 115
You are installing HP SIM on an HP workstation running Windows XP Professional. All the managed servers are running Red Hat Enterprise 3.0. Which additional software must be installed?
A. Linux interface layer for XP
B. HP Management Agents for workstations
C. WMI Mapper
D. MSDE 2000 SP3a
Answer: D
QUESTION NO: 116
Which combination of tools should be used to provide information to support an HP ProLiant prefailure warranty claim? Select THREE.
A. HP Insight Management Agents for HP ProLiant
B. HP Insight Diagnostic (Online and Offline)
C. HP Smart Setup Enterprise Edition
D. HP OpenView Network Node Manager
E. HP System Management Homepage
Answer: A,B,E
QUESTION NO: 117
What would be your next step after installing Microsoft Windows Server 2003 on your ProLiant DL380 G4 using the newest version of SmartStart?
A. upgrade the system and options ROMs
B. install the HP approved drivers for the Operating System
C. test all fault tolerant features like NIC teaming, redundant power supplies, etc
D. write the scope of work
Answer: C
QUESTION NO: 118
What happens on a SATA disk when you click the "flash LED" button in the "Status" tab of Insight Diagnostics?
A. It will update the LED firmware of the hard drive.
B. It will turn on the drive's front panel blue LED.
C. It will turn on all drive's front panel LEDs.
D. It will turn on the drive's front panel amber LED.
Answer: B
QUESTION NO: 119
Your customer requires a 3U rackmount server with AMD processors with internal RAID 5 capability. Which HP ProLiant system would you recommend?
A. ML570
B. DL580
C. BL35p
D. DL385
Answer: D
QUESTION NO: 120
Which pre-project document is crucial for ensuring a mutual understanding between you and your customer?
A. Scope of Work
B. Bill of Materials
C. Statement of Work
D. Build Instructions
Answer: A
QUESTION NO: 121
Where can you get the most updated BIOS firmware for a ProLiant Server?
A. Firmware CD included with ProLiant Server
B. HP PartSurfer on HP website
C. SmartStart CD included with ProLiant Server
D. Software and driver webpage on HP website
Answer: D
QUESTION NO: 122
Which feature is specific to the Remote Deployment Console Utility for Microsoft Windows?
A. It is created to be used with the Integrated Lights-Out 2.
B. It is only available for Windows 2003 Data Center release.
C. It is command-line based which allows for scripted installations.
D. It allows for user intervention during a remote installation.
Answer: C
QUESTION NO: 123
When must you manually reboot a system on which the Version Control Agent (VCA) has performed a component install?
A. when the VCA log is corrupted and not able to communicate with the VCRM server
B. when Version Control Repository Manager (VCRM) is not used for patch deployment
C. when you are not able to remotely execute the command
D. when the automatic reboot option has not been selected for patches that require a reboot
Answer: D
QUESTION NO: 124
Your customer needs a database server that will use minimum rack space with maximum internal storage capability. Which HP ProLiant server should you recommend?
A. HP ProLiant DL 380
B. HP ProLiant BL 35p
C. HP ProLiant ML 370
D. HP ProLiant DL 360
Answer: A
QUESTION NO: 125
Which backup software is included with all HP branded LTO drives?
A. StorageWorks Data Protector Express with a single-server license
B. Legato single-server version
C. Yosemite TapeWare Enterprise Edition trial version
D. Symantec/Veritas Backup Exec 2TB license version
Answer: A
QUESTION NO: 126
What would you do to change your MSA30 from a single SCSI bus to a dual SCSI bus architecture?
A. upgrade the EMU module
B. change the configuration switch on the backplane
C. install a dual port I/O module
D. install a dual port backplane
Answer: C
QUESTION NO: 127
You replaced the Smart Array 642 controller on a ProLiant ML370 G3. Before starting Windows Server 2003, what should you verify first?
A. the online spare drive is available and assigned
B. the boot controller is set correctly
C. the firmware of the new controller is up-to-date
D. the "set Smart Array corrected" is selected in ROM Based Setup Utility (RBSU)
Answer: C
QUESTION NO: 128
What does the "Erase NVRAM/Boot disk" do that the "Erase Non-volatile Memory" option cannot do in ROM-based Setup Utility (RBSU)?
A. It sets disk 0 as boot disk.
B. It completely erases the boot disk.
C. It sets the boot order to default.
D. It clears the array configuration.
Answer: B
QUESTION NO: 129
In a single server environment, which tool is best for setting thresholds on disk or processor utilization?
A. HP Workload Management Pack
B. HP Performance Management Pack
C. HP System Management Homepage
D. HP Systems Insight Manager
Answer: C
QUESTION NO: 130
Which controller supports serial-attached SCSI (SAS) disk drives in the HP ProLiant DL385 G1 server?
A. SmartArray 6i
B. HP 6-ports SATA/SAS controller
C. SmartArray 6404
D. SmartArray P600
Answer: D
QUESTION NO: 131
You installed 2GB of memory into a ProLiant server but during POST only 1GB is detected. What should you do to resolve this problem?
A. Check if the Intel Xeon processor with HT support is installed.
B. Check if Advanced Memory Protection is enabled in RBSU.
C. Check if dual bank memory configuration is enabled in RBSU.
D. Install the latest firmware on the memory controller board.
Answer: B
QUESTION NO: 132
What is an advantage of the ProLiant ML-series servers?
A. cooling efficiency
B. rapid deployment and provisioning
C. power efficiency
D. internal expansion
Answer: D
QUESTION NO: 133
Which NIC feature enables high-speed, low processor utilization and low-latency performance between your server and an iSCSI network storage disk array?
A. FastEther Channel
B. Adapter Teaming
C. TCP Offload Engine (TOE)
D. Remote Direct Memory Access (RDMA)
Answer: C
QUESTION NO: 134
You need to develop a backup strategy for your SMB customer. Which tape-rotation scheme is most commonly used in the SMB environment?
A. SMB Tape Rotation Schema (SMB TRS)
B. Fast Tape Switch for SMB (FTS for SMB)
C. Grandfather-Father-Son (GFS)
D. Grandmother-Daughter-Mother (GDM)
Answer: C
QUESTION NO: 135
You need to manage between 16 to 48 servers using a cascading console switching solution over CAT5 UTP cables. Which console do you need?
A. HP DVI Console Switch
B. HP KVM Console Switch
C. HP IP Console Switch
D. HP FireWire Console Switch
Answer: C
QUESTION NO: 136
Installation services are part of the Deployment Support Services offered by HP. Which other service type is included?
A. Software Product Updates
B. Support Plus
C. Education
D. Proactive 24
Answer: C
QUESTION NO: 137
Your customer needs on-site hardware support and over-the-phone software support 24 hours per day, 7 days per week, and 365 days per year? Which service should you recommend?
A. Support Plus
B. Proactive 24
C. Critical Service
D. Support Plus 24
Answer: D
QUESTION NO: 138
You see in the documentation for a ProLiant ML350 G4 that it is designed with high-availability features. What does this include? Select TWO.
A. The server has more than one power supply.
B. You can install more than 4GB of memory.
C. The server has redundant fans.
D. The server comes standard with a Call-to-Repair (CTR) Care Pack.
E. The server has online spare processors.
Answer: A,C
QUESTION NO: 139
What is the purpose of Dynamic Setup Support on a ProLiant server?
A. It selects automatically the available dynamic disks during the installation process.
B. It enables the operating system to automatically find the necessary boot drivers on the virtual install disk.
C. It selects automatically the correct operating system in RBSU when inserting the operating system CD during installation.
D. It enables a simpler setup process when using the assisted operating system installation on SmartStart.
Answer: B
QUESTION NO: 140
How do you access the Option Rom Configuration for Arrays (ORCA) utility?
A. by booting from the ORCA CD which comes with the array controller
B. by pressing DEL when prompted during the POST process
C. by pressing F8 when prompted during the POST process
D. by booting the SmartStart CD and selecting ORCA from the tools menu
Answer: C
QUESTION NO: 141
What must you do when you want to upgrade an existing MSA500 G2 to a solution with failover capability? Select TWO.
A. add a second enclosure to the chassis
B. add a second controller
C. upgrade the I/O module to an 8-port model
D. synchronize the firmware between both controllers
E. add a second EMU module
Answer: B,D
QUESTION NO: 142
Which HP tool can be used to configure enclosure, power and interconnect options for HP BladeSystems and create a list of all components used in this configuration?
A. HP BladeSystem Design Reference Guide
B. HP Infrastructure Sizing Tool for BladeSystem
C. HP BladeSystem p-Class Sizing Tool
D. HP Rack Builder Online
Answer: C
QUESTION NO: 143
Your customer connected an MSA20 to a ProLiant server. Which tool can be used to configure this storage subsystem?
A. ROM Based Setup Utilities (RBSU)
B. Array Configuration Tool (ACT)
C. Flexible Array Storage Tool (FAST)
D. Array Configuration Utility (ACU)
Answer: D
QUESTION NO: 144
When performing a manual update of the version control repository, which step should be performed next to ensure the files are correctly displayed in the VCRM homepage?
A. rescan the catalog
B. rescan the index
C. rebuild the repository
D. rebuild the index
Answer: A
QUESTION NO: 145
Your customer wants to purchase a new server that is fast, reliable and expandable. The server needs to support RAID 5 internally. Which model would you recommend?
A. ProLiant DL360 G4
B. ProLiant ML370 G4
C. ProLiant DL100 G1
D. ProLiant DL145 G2
Answer: B
QUESTION NO: 146
Which tool is provided with HP ProLiant servers for setting and monitoring performance thresholds?
A. SmartSetup
B. Workload Management Pack
C. Systems Insight Manager
D. GlancePlus Pack
Answer: C
QUESTION NO: 147
What is the recommended method for updating the repository in Version Control Repository Manager (VCRM)?
A. auto update from the SmartStart CD
B. auto update from the HP website
C. auto update from the Firmware Maintenance CD
D. auto update from the VCRM subscription CD
Answer: B
QUESTION NO: 148
Which tool allows you to manage multiple IP console switches?
A. HP IP Console Viewer on all machines that will be used for administrative tasks
B. HP IP KVM Administrative console on all machines that will be used for administrative tasks
C. HP System Management Homepage for IP console
D. HP IP Console Multiplexer
Answer: A
QUESTION NO: 149
Which system health status is indicated by a flashing green LED on a ProLiant blade server?
A. booting
B. normal
C. critical condition
D. degraded condition
Answer: A
QUESTION NO: 150
Which tool allows you to change stripe size, migrate RAID level and change the rebuild/expand priority?
A. Array Diagnostic Utility (ADU)
B. ROM Based Setup Utility (RBSU)
C. Array Configuration Utility (ACU)
D. Option ROM Configuration for Arrays (ORCA)
Answer: C
QUESTION NO: 151
Your customer is experiencing a performance bottleneck on one of their server. They have exceeded the budget for the year, but it is critical that the server performance improves. Which solution should you recommend?
A. Add more memory to the server.
B. Disable HyperTransport.
C. Add an additional server.
D. Check and enable memory interleave.
Answer: D
QUESTION NO: 152
You want to install the ProLiant Support Pack (PSP) on a server running Red Hat Enterprise Linux 3.0 using the deployment utility; however, the installation does not proceed. What could be the issue?
A. You are running the utility from a read-only media (CD-ROM).
B. The PSP was not pre-configured.
C. You have no access to the system.
D. The deployment utility is only supported on Windows operating systems.
Answer: C
QUESTION NO: 153
Which combination of HP management products allows you to track up to ten snapshots of your local server configuration? Select TWO.
A. Virtualization Management Software
B. Systems Insight Manager
C. Business Copy
D. System Management Homepage
E. Insight Diagnostics Online Edition
Answer: D,E
QUESTION NO: 154
Which situation can cause the Version Control Agent (VCA) to deny access to the Version Control Repository Manager (VCRM)?
A. The VCA is not identical to the version of the VCRM.
B. The trust relationship (security access) between the two system is not secured.
C. The VCA is pointing to a different IP gateway address.
D. The trust relationship (security access) between the two systems is not configured correctly.
Answer: D
QUESTION NO: 155
Which utility validates the hardware of an unstable ProLiant DL380?
A. HP Insight Diagnostics Offline Edition
B. Performance Management Pack (PMP)
C. HP OpenView Network Node Manager
D. Microsoft System Monitor
Answer: A
QUESTION NO: 156
Which processors are used in the HP ProLiant server family? Select TWO.
A. AMD Opteron
B. Intel Core Dual Mobile
C. Transmeta processors
D. AMD Athlon XP
E. Intel Pentium Xeon DP and MP
Answer: A,E
QUESTION NO: 157
Your customer is not obtaining the necessary I/O performance from their disk storage subsystem. What should you recommend to increase disk I/O if the situation consists primarily of random I/Os?
A. Reduce the number of disks the system accesses.
B. Change to disks with faster rotational speed.
C. Increase the number of disk controllers.
D. Upgrade to a faster processor.
Answer: B
QUESTION NO: 158
You are assigned to add 35 HP ProLiant DL360 units to an existing 42U HP Rack. The rack is power protected by two UPSs that are currently protecting the systems in the rack. What information would you need and which utility would you use?
A. Use HP Enterprise Configurator to find the serial cable needed to connect to the UPS for proper system shutdown.
B. Use HP System Insight Diagnostic Online to gather the DC-DC conversion rate for each power supply and compare it to the workload on the UPS.
C. Use HP Product Bulletin to find the cooling requirements for each system (BTU/Hr) and its impact to the UPS Performance.
D. Use the HP Power Calculator Program to determine (sum) the total VA workload and compare it with the balance workload on the UPS.
Answer: D