hp 5l_6l_ax

8/20/2019 HP 5L_6L_ax

http://slidepdf.com/reader/full/hp-5l6lax 1/4

HP Laserjet 5L/5ML

HP Laserjet 6LSE/6LXIHP Laserjet 3100

Canon LBP-460

Canon Laser Class4000/4500 (FX3)

Part Number: C3906A

Gram Load: 140 gramsYield @ 5%: 2500 pgs

Pages/Min.:4ppm

Resolution: 600 dpi

Funnel

Diagonal PliersNeedle Nose Pliers

Phillips #2 Screwdriver

Small Flat Blade Screwdriver140 Grams of 5L Toner

Damp ClothSoft Lint-Free Cloth

Technical Instructions Printers OEM Info Tools

Step 1

Place the AX cartridge on a table with the

handle facing up. Using diagonal pliers,pull the steel lock pin from one end and

then the other. The cartridge separatesinto waste hopper and toner hopperhalves. Place the toner hopper aside.

(See Photo 1)

Photo 1

Photo 2a

Photo 2b

XTECH

Step 2

Using needle nose pliers, grasp the metal

drum axle (at the notch) on the large gearend of the waste hopper, while holding

the hopper securely with the other hand.Now, simply pull the pin straight out andset it aside.

(See Photo 2a)

Grasp the drum gear, lift it up,and pull thedrum straight out. Wrap the drum in pro-

tective cloth or paper and set it aside.

(See Photo 2b)

E-mail: [email protected] Website: www.futuregraphicsllc.com

US 1 800 394.9900Int’l +1 818 837.8100FAX 1 800 394.9910Int’l +1 818 838.7047

DAL LAS , U S A

US 1 877 499.4989Int’l +1 972 840.4989

FAX 1 877 774.1750Int’l +1 972 840.1750

ATLANTA, USA

US 1 877 676.4223Int’l +1 770 516.9488FAX 1 877 337.7976Int’l +1 770 516.7794

MI AMI , U S AUS 1 800 595.429Int’l +1 305 594.3396FAX 1 800 522.8640Int’l +1 305 594.3309

SANFORD,USAUS 1 800 786.9049Int’l +1 919 775.4584FAX 1 800 786.9049Int’l +1 919 775.4584

TORONTO, CAN

CAN 1 877 848.0818Int’l +1 905 712.9501FAX 1 877 772.6773Int’l +1 905 712.9502

N E W YORK, U S A

US 1 800 431.7884Int’l +1 631 345.0121FAX 1 800 431.8812Int’l +1 631345.0690

SYDNEY, AUS

AUS 1 800 003.100Int’l +62 02 9648.2630FAX 1800 004.302Int’l +62 02 9548.2635

B UE NO S A IR E S, A R G

ARG 0810 444.2656Int’l +011 4583.5900FAX +011 4584.3100

MONTEVIDEO,URY URY 02 902.7206Int’l +5982 900.8358FAX +5982 908.3816

JO HA NN ES BU RG , S. A.S.A. +27 11 974.6155FAX +27 11 974.3593

MELBOURNE, AUS

AUS 1 800 003. 100Int’l +62 03 9561.8102FAX 1 800 004.302Int’l +62 03 9561-7751

CORPORATE

LOS ANGELES, USA

8/20/2019 HP 5L_6L_ax


Photo 3

Step 4

Remove the two wiper blade screws wia Phillips screwdriver. Now, using need

nose pliers, grasp the upward angleedge of the wiper blade lifting upwardand out.

(See Photo 4)

Next, clean the wiper blade with a damcloth (or, wiper blade cream) and setaside. The waste hopper can now b

emptied and vacuumed. In doing so, bcareful not to damage the recovery blad

Photo 6

Step 7

Remove the end cap from the waste ho

per and clean old conductive grease frothe contact spring and plate. Set the en

cap aside and remove the small white platic mag roller bushing.

(See Photo 7)

Photo 7

Need trust-worthy, detailed Technical

Instructions for another engine?

Vi si t: ww w. fu tu re gr ap hi cs ll c. co m

2 AX Technical Instructions

Photo 4

Step 3

Remove the primary charge roller (PCfrom its clips and set it aside. Note ththis roller is similar to the 5P in that it h

a much more pliable covering than tharder PCRs found in the LX and PX ca

tridges and is easily damaged.

(See Photo 3)

Step 6

Examine the toner hopper. There are gea

at one end and the bias connector at thother. One screw on each end holds tend caps. Both caps can be removed

you’re curious, but only the non-gear enneeds to be taken off. With this end facin

you, remove the screw.

(See Photo 6)

Step 5

Reassemble the waste hopper by following the above steps in reverse order. Put t

wiper blade back in and tighten the two screws gently. Wipe all toner from the PCR wthe damp cloth and dry it with the soft, lint-free cloth. Put the PCR back into its cl

Install a new drum (or, a clean OEM drum) and both axles. Set aside with the drum c

ered.

Notes

8/20/2019 HP 5L_6L_ax


Photo 10

Photo 11

Step 11

Re-install the doctor blade on the wastehopper and insert and tighten screws.Drop the drive gear back into its slot-

with the notch on the flat area facing tothe left.

(See Photo 11)

Now, put the long white plastic bushingon the left end of the mag roller bygrasping the right end of the mag roller,

lay it down into the hopper and slide theshaft into the white plastic guide on the

left. Turn the mag roller until the flat sideof the shaft matches the flat area of thegear, and insert into position.

Need help with a particular remanu-

facturing problem? Call the Technical Resource Center from

8am - 5pm PST: 800 394.9900

AX Technical Instructions

Photo 8

Step 8

Grasp the mag roller with your righthand, while holding the toner hoppersecurely with your left. Lift it upwards

and to the right.

(See Photo 8)

Photo 9

Step 9

Remove the large white plastic bushing anddrive gear from the left. Then remove the

two screws from the doctor blade and liftthe blade out.

(See Photo 9)

NOTE: Avoid breaking off the small locat-

ing pin on the left.

Step 10

Remove the fill plug, empty out anyremaining toner and vacuum, making

sure not to damage the lower mylar strip.Clean all toner from the mag roller clean-

er. Insert seal.

(See Photo 10)

NOTE: The black square guide in the seal

exit slot may be removed to facilitate sealinstallation, and then reinserted.

Notes

8/20/2019 HP 5L_6L_ax


Photo 12

Photo 14

4 AX Technical Instructions

Step 12

Hold the toner hopper in one hand wiyour thumb on the shiny area of the maroller to keep it in position. A funnel w

help you fill the hopper from a toner botle.

(See Photo 12)

Step 13

Replace the fill plug. Put the small white plastic bushing on the right end of the mroller. Now place the end cap over the plug and align the “D” shaped hole with t

mag roller shaft by turning the mag roller gear on the other end. Insert and tightthe last remaining screw.

Step 14

Finally, fit the two halves together, aliging the springs on the toner hopper wi

the positioning pins on the waste hoppe

(See Photo 14)

Align the matching holes on each end bpressing the springs against their sea

and insert and press home the lockinpins.

Need trust-worthy, detailed Technical

Instructions for another engine?

Vi si t: ww w. fu tu re gr ap hi cs ll c. co m

Comparing Operating Specifications

OEM No. Toner Drum Drum PCR Shaft

Cartridge OEM PPM of Pages OEM Fill Diameter Length PCR Length

Type/Model Ctg. # @ 5% Density (grams) (mm) (mm) Rubber (inches)

AX/5L C3906A 4 2,500 1.46 140 24 245 Soft 9.54

PX/4L, 4P 92274A 4 3,000 1.52 160 24 257 Hard 9.46

VX/5P, 5MP C3903A 6 4,000 1.52 225 24 257 Soft 9.54

LX/2P 92275A 4 3,500 1.43 225 30 254 Hard 9.46

E-mail: [email protected] Website: www.futuregraphicsllc.com

Future Graphics (FG) is a distributor of compatible replacement parts and products for imagining equipment. None of FG's

products are genuine OEM replacement parts and no affiliation or sponsorship is to be implied between FG and any OEM.

Notes

hp 5l_6l_ax

Documents