high pressure cleaners - kranzle uk ltd handbook.pdf · high pressure cleaners operating manual ......
TRANSCRIPT
GB
High Pressure Cleaners
Operating manual
Read and conform
safety instructions
before use
( 220-240 V / 50/60 Hz )
( 110-127 V / 60 Hz )
2
Dear customerWe would like to congratulate you on your new high pressure cleaner with integratedundercarriage and integrated hose drum and to thank you for the purchase.
To ease your introduction to the use of the cleaner, we have provided the followingpages of explanations, tips and hints, which we ask you to read before using for thefirst time.
The equipment will assist you professionally in all cleaning tasks, e.g.:
Permissible tolerance for figures ± 5 % in acc. with VDMA uniform sheet 24411
Technicaldata
Operating pressure,steplessly adjustable
Perm. overpressureWater output
Hot water input (min. 1-8 bar)
Suction heightHigh pressure hose
with hose drumElectrical ratings
Connect. wattage inputoutput
Weight
Dimens. with mountedHandel in mm
Sound level acc.to 45635with dirtkillerGuaranteed sound level LWA
Recoil at lanceVibrations at lance
Order n°:K 1150 / K1120with dirtkiller
K 1150 T
KränzleK1150
K1150 T
KränzleK1120-60Hz
K1120T-60Hz
10 - 130 bar (1900 PSI )
150 barat 2800 rpm10 l/minmax. 60 °C1.0 m10 m
15m220 - 240V ;50 Hz ; 12,5 AP1: 2.8 kWP2: 2.0 kW
22 kg (K 1150 )26 kg (K 1150 T)300 x 330 x 800
88 dB (A)90 dB (A)93 dB (A)approx. 27 N
1,9 m/s²
41.21141.211 141.210 1
10 - 95 bar( 1400 PSI )120 bar (1800PSI)
at 1700 rpm8,3 l/minmax. 60 °C2.0 m10 m15m
110 - 127 V ;60 Hz; 6,7 AP1: 1.65 kWP2: 1.35 kW
22 kg ( K1120 )26 kg ( K1120 T )300 x 330 x 800
78 dB (A)80 dB (A)93 dB (A)
approx. 22 N1,9 m/s²
41.21341 213141.212 1
KränzleK1150-60Hz
K1150T-60Hz
10 - 130 bar( 1900 PSI )150 bar ( 2200 PSI )at 3400 rpm10 l/min
max. 60 °C1.0 m
10 m15m220 - 240 V ;60 Hz; 8,7 A
P1: 2.8 kWP2: 2.0 kW22 kg ( K 1150 )26 kg (K1150 T )
300 x 330 x 800
88 dB (A)90 dB (A)93 dB (A)approx. 32 N
1,9 m/s²
41.211 241.211 341.210 3
Description
- facades- flagstones- terraces
- vehicles of all types- containers- machines etc.
- removing of old paint
*
Minimum quantity of water to be led to the equipment (see page 7)*
3
Construction
Description
The KRÄNZLE 1120 / 1120 T + 1150 / 1150 T - high pressure cleaners aremobile machines. The design can be seen from the diagram.
Item1 Water inlet connection with filter2 Suction hose with filter (special accessory) Order no. 15.038 33 High pressure pump4 Press. gauge with glycerin filling5 Unloader valve - safety valve
6 High pressure injector forcleaning agents
7 High pressure hose8 Spray gun9 Interchangeable lance with reg.
nozzle
33
33
9 8
2
Water
7
4 5
3
6 1
4
Description
Water and Cleaning / Pflegemittel SystemWater can be connected at mains pressure to the high pressure pump or itcan be sucked directly from a storage tank. The water is then forced underpressure by the high pressure pump to the lance. The high pressure jet isformed by the nozzle at the end of the lance.
Detergent and caring agents can be added through a highpressure injector.Up to max 20m HD hose length.The rules concerning the environment, refuse andground water protection must be complied with!(Information to be obtained from environmental dept, townworks, etc.)
Lance with trigger gunThe machine can only be operated when the safety trigger is squeezed. Themachine can only be operated when the safety trigger is squeezed. Whenthe lever is squeezed, the spray gun opens. The liquid is then pumped tothe nozzle. The spray pressure increases and quickly reaches the selectedoperating pressure.When the trigger is released, the trigger gun closes and any further sprayingof liquid from the lance is stopped.The increase in pressure when the trigger gun is closed causes the unloadervalve-safety valve to open. The pump remains switched on and continues topump liquid through the pump at reduced pressure. When the trigger gun isopened, the unloader valve - safety valve closes and the pump ressumespressure spraying from the lance
The trigger gun is a safety device. Repairs shouldonly be performed by qualified persons. Shouldreplacement parts be required, use only componentsauthorized by the manufacturer.
Unloader valve - safety valveThe unloader valve - safety valve protects the machine from a build p ofexcess pressure, and is designed not to permit an excess pressure to beselected for operation. The limit nut on the handle is sealed with a spraycoating.*(see page 22:"Stopping leaks from the hose or gun".)The operating pressure and spray rate can be steplessly adjusted by turningthe handle.
Replacements, repairs, new adjustments and sealingshould only be performed by qualified persons.
5
Description
The motor is protected from overload by a motor protection switch, whichautomatically cuts out the motor in the event of overload. However shouldthe switch trip frequently, the cause of the malfunction should be located andrectified (see page 6).
Motor protection switch
Setting up
Neither set up and operate the machine in rooms where there isa risk of fire or explosion nor put it into puddles. Do not use themachine under water.
Never use liquid containing solvents such as paint thinners,petrol, oil or similar liquid matter. Pay attention to the in-structions of the manufacturers of the cleaningagents. The seals in the machine are not resistant to solvents.The spray of solvents is inflammable, explosive and poisonous.
CAUTION !
CAUTION !
When running your high pressure cleaner with hot water of 60° Craised temperatures occur. Do not touch the machinewithout safety gloves!
Replacements and inspection work should only be performed byqualified persons when the machine is disconnectedfrom the power supply, i.e. pull out the plug from theelectrical socket.
Location
6
Electrical connectionThe machine is supplied with an electrical power cord with plug.
The mains plug must be fitted to a standard grounded socketwith a 30mA residual current operated device. The socket mustbe protected with a 16A delay action fuse on the mains side.
KRÄNZLE 1150 / 1150 T - 220-240 VKRÄNZLE 1150 / 1150 T - 220-240 VKRÄNZLE 1150 / 1150 T - 220-240 VKRÄNZLE 1150 / 1150 T - 220-240 VKRÄNZLE 1150 / 1150 T - 220-240 Volt 50 Hzolt 50 Hzolt 50 Hzolt 50 Hzolt 50 HzKRÄNZLE 1120 / 1120 T - 110-117 VKRÄNZLE 1120 / 1120 T - 110-117 VKRÄNZLE 1120 / 1120 T - 110-117 VKRÄNZLE 1120 / 1120 T - 110-117 VKRÄNZLE 1120 / 1120 T - 110-117 Volt 60 Hzolt 60 Hzolt 60 Hzolt 60 Hzolt 60 HzKRÄNZLE 1150 / 1150T - 220-240 VKRÄNZLE 1150 / 1150T - 220-240 VKRÄNZLE 1150 / 1150T - 220-240 VKRÄNZLE 1150 / 1150T - 220-240 VKRÄNZLE 1150 / 1150T - 220-240 Volt 60 Hzolt 60 Hzolt 60 Hzolt 60 Hzolt 60 Hz
When using an extension cable, this must have an earthed leadwhich is properly connected to the socket. The conductors in theextension cable must have a minimum cross section of 1.5 mm².Plug connections must be of a spray-proof design, and may notbe located on a wet floor.(with extension cables of more than 10 m - 2.5 mm2 )
CAUTION !
The use of extension cables which are too long may lead to malfunctionsand start up difficulty.
When using a cable drum, always keep the cable wound as far as possible.
Description
110 V - 127 V220 V - 240 V
7
Description
Please check that the high pressure cleaner has available the quantityof water specified on page 2 (techn. specs.) (Litres per minute) .
Water connection:
Test:
Allow the water supply hose to run for 1 minute into a bucket.
The received quantity of water must be at least the quantity given on page 2 !!!
Lack of water causes fast wear on seals (nowarranty)
33
8
Brief operating instructions
Description
The high pressure hose and spraying device supplied with the machine aremade of high grade material, they are also optimized for the machine andmarked as required by the appropriate regulations.- Hose length max. 20m.
If replacement parts are required, only such parts thatare authorized by the manufacturer and which bear themarkings required by the appropriate regulations maybe used. The high pressure hose and spray devicemust be connected in a pressure-tight manner (noleak). The high pressure hose may not be driven over,pulled excessively, or twisted. The hose may under nocircumstances be pulled over sharp edges, since other-wise the guarantee is automatically void.
High pressure hose and spray device
Please pay attention to the regulations of your waterworks company. Inaccordance with EN 61 770, the machine may not be directly connected tothe public drinking water supply lines.
A brief connection however is permissible according to DVGW (GermanAssociation for Gas and Water Affairs) if a tube ventilator with check valve(Kränzle Order-No. 41.016 4) is built into the water supply.
Also indirect connection to the public drinking water supply lines is permissi-ble by way of free emission in accordance with EN 61 770; e.g. by using areservoir with a float valve.
Direct connection to a non-drinking water supply line is permissible.
CAUTION !
When operating your high pressure cleanerpay attention that it is in a horizontal position.1 . Connect the high pressure hose with spray gun.2 . Connect to suitable water supply.3 . Flush the air from the pump (open and close the
spray gun several times)4 . Make the electrical connection5 . Switch on the machine with opened spray gun and commence
cleaning.6 . After completing the work, completely empty the pump (switch
the motor on for approximately 20 seconds without thesuction and spray gun). - Only use clean water ! Protect from frost !- Only use clean water ! Protect from frost !- Only use clean water ! Protect from frost !- Only use clean water ! Protect from frost !- Only use clean water ! Protect from frost !
9
Safety notes
As to the recoil -see notice on page2 !
Always aim theunderbody lance.Note when using anangled underbodylance, like for exam-ple lance No. 41.0751, that there is acertain amount oftorque in the recoil.(See also notice onpage 2)
Apply the safety catch onthe spray gun after eachuse, in order to preventunintentional spraying!
10
1. Dirtkiller with nozzle 045 (at 1120 T and 1150 T)
2. Spray lance withVario - Jet nozzle
3. Spray gun withinsulated pistol gripand screw connection
4. KRÄNZLE - High pressure cleaners 1120 T / 1150 T (50/60 HZ)with hose drum and 15 m high pressure hose with steel reinforcement
This is what you’ve purchased:
5. Crosstip screwdriver
Fixing screw for crank
6. Operating instructions
8. Water inlet components
7. Crank for hose drum
11
Hose drumwith HP-hose
Receptaclefor gun
Receptaclefor lances
Put high pressure cleaner into uprightposition. Remove the screw from thebrass element. Put the crank on thehexagon and fasten with the screw.
How to assemble and furnish your high pressure cleaner
12
33
Preparation for use
2. Connect the high pressurelance to the spray gun.
High pressure hoseconnected to machineand spray gun.
1. Put high pressure cleaner intohorizontal position!
THE HIGH PRESSURECLEANER IS ONLY TOBE OPERATED INHORIZONTALPOSITION !
Unroll hosewithout kinks and
connect with handgun andpump. Max. extension 20m-HP
hose or 2 x 10m with hoseconnections.
13
33
4 . The machine can be connected toa pressurised water line with
60°°°°°C hot water (see page 2).Ensure that the water supply isclean when sucking from externalsources. The hose cross sectionmust be at least 1/2" = 12.7 mm
(free passage). Filter 1 mustalways be clean.
Please make surethat the filter is clean beforeusing your high pressurecleaner.
CAUTION !
When running your high pressure cleaner with hot water of60°°°°° C raised temperatures occur.Do not touch the pump without safety gloves!
Preparation for use
Water
5. Maximum inductionheight 1,0 msee technicaldata on page 2
14
1. Switch off the machine.2. Cut off the water supply.3. Open the spray gun briefly until the pressure is released.4. Apply the safety catch on the spray gun.5. Remove the water hose and spray gun.6. Drain the pump: switch on the motor for approx. 20 seconds.7. Pull the plug from the socket.8. Winter: store the pump in rooms above 0°°°°°C.9. Clean the water filter.
33
33
chem. Pmax
4
5
A mixing ratio of 3-5% is achieved whenthe Vario-Jet is fully turned on. pH valueneutral 7-9.
Turn on Vario-Jet to reach lowpressure !
This is accomplished by turning thehandwheel. The default setting ismaximum pressure.
Adjusting the pressure
Unwind HP-hose completely.Place chemical filter no. 5 in thereservoir with the cleansing agent.Turn on Vario-Jet No. 4 to to enable theinjector to induct the cleansing agent. Byturning back the Vario-Jet nozzle, the supply ofchemical is automatically cut off. Allow the cleans-ing agent to take effect and then remove with highpressure spray.
When using cleansing agents:
Note that you must alwayscomply with the instructionsprovided by the manufac-turer of the cleansing agent(e.g. instructions concerningsafety clothing) and the waterprotection regulations!
To shut down the pump:
Preparation for use
Max high pressure hoselength 20m
15
Never direct thewater jet at themachine itself !
Never direct thewater jet at a powersocket !
Never allow childrento use the highpressure cleaner !
This is prohibited !
16
This is prohibited !
Never direct thewater jet at peopleor animals !
Do not damage thepower cord or repairit incorrectly !
Never pull the highpressure hose if ithas formed kinks or“nooses”!Never pull the hoseover sharp edges !
17
Rotary scrubbing brushRotary scrubbing brushRotary scrubbing brushRotary scrubbing brushRotary scrubbing brushOrder No. 41.050 1
Drain and pipe cleaning hoseDrain and pipe cleaning hoseDrain and pipe cleaning hoseDrain and pipe cleaning hoseDrain and pipe cleaning hose10 m - Order No. 41.058 115 m - Order No. 41.058
Underbody lance, newUnderbody lance, newUnderbody lance, newUnderbody lance, newUnderbody lance, newOrder No. 41.075 1
SandblasterSandblasterSandblasterSandblasterSandblasterOrder No. 41.068 1
Flat brushFlat brushFlat brushFlat brushFlat brushOrder No. 41.073
DirtkillerDirtkillerDirtkillerDirtkillerDirtkillerOrder No. 41.072 5
Environmental, refuse disposal and waterEnvironmental, refuse disposal and waterEnvironmental, refuse disposal and waterEnvironmental, refuse disposal and waterEnvironmental, refuse disposal and waterprotection regulations must be observedprotection regulations must be observedprotection regulations must be observedprotection regulations must be observedprotection regulations must be observedwhen using the accessories!when using the accessories!when using the accessories!when using the accessories!when using the accessories!
Additional KRÄNZLE-accessories for ...
18
Car cleaning, glass, caravan, boat etc.rotary washing brush with 40 cm exten-sion and ST 30 nipple M 22 x 1,5
Underbody cleaning of cars, trailers andequipment: lance 90 cm with high pressurenozzle and ST 30 nipple M 22 x 1,5.The lance must be aimed when spraying.
Cleaning cars and all smooth surfaces :brush with ST 30 nipple.
Rotary point sprayer for extreme soiling.Dirtkiller with 40 cm extension and ST 30nipple.
Cleaning pipes, channels and drains:pipe cleaning hose with KN nozzleand ST 30 nipple M 22 x 1,5
Blasting old paint, rust and facades: sand-blasting injector with suction lance, 3 mPVC hose and ST 30 nipple.
When sandblasting youWhen sandblasting youWhen sandblasting youWhen sandblasting youWhen sandblasting youmust wear protectionmust wear protectionmust wear protectionmust wear protectionmust wear protectionclothes! Pay attention toclothes! Pay attention toclothes! Pay attention toclothes! Pay attention toclothes! Pay attention tothe instructions of thethe instructions of thethe instructions of thethe instructions of thethe instructions of themanufacturer of themanufacturer of themanufacturer of themanufacturer of themanufacturer of theabrasive!abrasive!abrasive!abrasive!abrasive!
... for further combination possibilities
19
The pressure gauge shows a 10% higher pressure than the working pressure.
You only get a weak flow of water or no water at all!Small repairs - Do it yourself!
The injector may be dirty and you should first remove the hose!
Then straighten apaper clip ...
... release feed line and injector with an open- ended spanner ...,
... and pull outthe injector!
Clean the injectorthoroughly from bothsides ...
and check that itis clean.
Reconnect thehose ...
and you areready to continue your work!
Now turn on the water andyou should get a powerful stream of water
Reconnect injector and feed line.
But if you onlyget a weak flow
20
The nozzle is blocked!No water but the gauge shows full pressure !
Small repairs -
Rinse the hose through first.
You should now have apowerful stream of
water,
but if you only get a few drops from the lance
remove the lance and clean the nozzle.
Using the flat spray lance youonly have to clean the front
nozzle.
Straighten a paperclip and clean the nozzle.Insert pointed object
into the hole and pullthe cap back!
Check visually whether thenozzle is clean.
Now it works as wellas before.
21
Nozzle dirty or sticky!- Do it yourself!
Pressure gauge does not show full pressure.Water comes out in spurts.If you do not use the high-pressure cleanerfor some time the valves can stick
The high-pressure hose vibrates.
Straighten apaper clip...
When a valve is blocked, the gaugeshows littlepressure orno pressure
at all,
or the highpressure
hose vibrates!
Open the valvewith a socket
wrench...
and remove thevalve screw, thevalve and theo-ring.
Replace the rubber o-ring.and remove the dirtfrom the valve - thevalve inside mustbe closed.
Retighten thevalve screw
...and repeaton all 6valves.
Now it worksas well asbefore!
22
Small repairs - Do it yourself!Stopping leaks from hose or gun
After closing the gun the manometer shows full pressure !The pressure regulator switches on and off contunuously!
If themanometershows fullpressure,
Press thetrigger to
release thepressure!!!
Firstdisconnectthe hose!
Then unscrew thepump outlet with anopen-jew wrench.
Clean the returnelement or replace
the O-Ring !
The pressureregulatorswitches onand off frompressureloss!
Water can emerge atthese 3 points.
Check the seals andreplace the O-Ringe if necessary
or ave the gun checked by the dealer.
Replace the O-Ringat the lance or at theHP hose respectively!
Reconnect the hose, gunand lance!
Problem solved already!
Pull out thepower plug!
23
Dirtkiller (special accessory)
No Description Qty. Ord.-No
1 Sprühkörper 1 41.5202 O-Ring 6,88 x 1,68 1 41.5213 Düsensitz 1 41.5224 Düse 045 1 41.5235 Stabilisator 1 41.5246 O-Ring 1 40.016 17 Sprühstopfen 1 41.5268 Rohr 400 mm 2x M 12 x 1 1 41.5279 ST 30-Nippel M 22 x 1,5 / M 12 x 1 ISK 1 13.36311 Kappe vorn für Schmutzkiller 1 41.528 112 Kappe hinten für Schmutzkiller 045 1 41.540 2
Rep.-kit Dirtkiller 045 41.097consisting of: 1x 2; 3; 4; 5
Dirtkiller 045 compl. with lance 41.072 5
24
Gun with lance
25
Sp
are
pa
rts
list
KR
ÄN
ZL
E 1
12
0/1
12
0 T
; 11
50
/11
50
TG
un
wit
h la
nc
e
KRÄNZLE 1120 - 1150 T
No
De
sc
rip
tio
nQ
ty.
Ord
.-N
o
5R
ohra
nsch
luß
teil
R1/
4"1
12.1
25in
cl. P
os. 3
, 4, 2
16
Sch
eibe
5,3
DIN
9021
150
.152
7A
bzug
-Heb
el k
pl.
112
.144
115
Roh
r ku
nsts
toffu
msp
ritzt
115
.004
2bd
s. R
1/4
" A
G16
Übe
rwur
fmut
ter
ST
30
M22
x 1
,5 I
G1
13.2
76 1
17A
ußen
-Sec
hska
nt-N
ippe
l R
1/4
" IG
113
.277
118
O-R
ing
9,3
x 2
,41
13.2
7319
ST
30-
Nip
pel
M 2
2 x
1,5
113
.363
20R
ohr
400
lang
, bd
s. M
12 x
11
15.0
0221
Alu
min
ium
Dic
htrin
g6
13.2
75 1
30K
lem
mst
ück
141
.155
231
Hal
teru
ng f
ür K
lem
mst
ück
141
.155
432
Kun
stof
fhül
le1
41.1
55 1
33V
ario
-Jet
045
141
.155
6
AR
ep.-
Kit
12.1
58P
os: 3
, 4, 5
, 8, 9
,10,
12,
15,
21B
Grif
f ko
mpl
ett
12.1
64
Mid
i-Pis
tole
kpl
.12
.160
La
nze
kp
l. m
it V
ari
o-J
et
41
.15
6
26
Complete assembly
27
KRÄNZLE 1120 - 1150 T
No Description Qty. Ord.-No
Spare parts list KRÄNZLE 1120 - 1150TComplete assembly
1.1 Motor-Pumpe K1150 ohne Schaltkasten 1 44.542 1.2 Motor-Pumpe K1150 mit Schaltkasten 1 44.542 1 1.3 Motor-Pumpe K1150T ohne Schaltkasten 1 44.543 1.4 Motor-Pumpe K1150T mit Schaltkasten 1 44.543 1 2 Fahrgestell 1 44.502 3 Frontplatte " K 1150 " 1 44.503 1 3.1 Frontplatte " K 1150 T " 1 44.503 4 Köcher groß 1 44.506 5 Köcher klein 1 44.507 6 Knickschutz 1 44.509 7 Rad 2 44.538 8 Radkappe 2 45.200 8 9 Kabelhalteplatte 1 44.505 10 Achse 2 44.504 11 Netzanschlußkabel 1 41.092 12 Chemikaliensaugschlauch mit Filter 1 15.038 13 Versteifungsplatte 1 44.511 15 Kunststoffsenkschraube 5,0 x 20 2 45.421 1 16 O-Ring 9,3 x 2,4 2 13.273 17 Kunststoffschraube 5,0 x 20 20 43.018 18 Auflagepuffer 2 44.510 19 Kunststoffschraube 5,0 x 30 2 41.412 20 Scheibe 40 x 6 x 1,5 (Stahl) 2 45.216 7 21 Unterlegscheibe 8,4 4 50.186 22 Innensechskantschraube M 8x 30 4 41.036 1 23 Kunststoffschraube 4,0 x 16 2 43.417 24 Kunststoffschraube 5,0 x 50 2 41.411 25 Kunststoffschraube 5,0 x 70 2 44.519 26 Kunststoffschraube 3,5 x 14 2 44.525 27 Anschlußleitung Schlauchtrommel 1 44.520 28 Midi-Pistole 1 12.160 29 Vario-Jet 045 kpl. mit Lanze 1 41.156 30 Schmutzkiller 1 41.072 5 31 Kabelklemme 1 43.431 32 Schraube 3.5 x 16 2 44.161 33 Griffabdeckung 1 44.535 34 Gummipuffer links+rechts 1 44.536 35 Rad kpl. (7, 8, 10, 15, 20) 2 44.538 2
28
Motor
29
No Description Qty. Ord.-No
1 Ölgehäuse 1 44.5012 Motorgehäuse mit Stator 230 V / 50 Hz 1 23.0022.1 Motorgehäuse mit Stator 110 V / 60 Hz 1 23.002 22.2 Motorgehäuse mit Stator 230 V / 60 Hz 1 23.002 33 Motorwelle mit Rotor 230 V / 50 Hz 1 43.0243.1 Motorwelle mit Rotor 110 V / 60 Hz 1 43.1043.2 Motorwelle mit Rotor 230 V / 60 Hz 1 43.6294 Paßfeder 6 x 6 x 20 1 41.483 15 Motor-Lager B-Seite Z-Lager 1 43.0256 Motor-Lager A-Seite Schulterl. 1 43.0268 Öldichtung 25 x 35 x 7 1 41.0249 Lüfterrad 1 43.02810 Lüfterhaube 1 41.49711 Flachdichtung 1 44.51312 Lüsterklemme 3-pol. 1 43.031 213 Schaltkasten 1 44.50814 Schalter mit 13,5 A-Überstromauslöser 1 41.110 215 Klemmrahmen mit Schalterabdichtung 1 43.45316 Kabelverschraubung PG 11 1 41.41917 Gegenmutter PG 11 1 44.52118 Kondensator 40 µF 1 43.035
K 1150 / K 1150 T ( 230V ; 50/60Hz )18.1 Kondensator 80µF für 1 43.505
K 1120 / K 1120 T ( 110V ; 50/60Hz )19 Netzkabel für 230V / 50/60Hz 1 41.09219.1 Netzkabel für 110V / 60Hz 1 43.51220 Blechschraube 3,5 x 9,5 2 41.08821 Blechschraube 2,9 x 16 1 43.03622 Innensechskantschr. M 5 x 12 4 40.13423 Innensechskantschr. M 5 x 30 4 42.13024 Erdungsschraube kpl. 1 43.03825 Deckel für Schaltkasten 1 44.51226 Dichtung für Deckel 1 44.52227 Kunststoffschraube 5,0 x 25 4 41.41428 Blechschraube 3,9 x 9,5 3 41.63629 Toleranzhülse 1 43.063 1
Motor compl. w. oil housing and 1 44.530fan wheel without elect. for 230V / 50 Hz
Motor compl. w. oil housing and 1 44.530 1fan wheel without elect. for 110V / 60 Hz
Motor compl. w. oil housing and 1 44.530 2fan wheel without elect. for 230V / 60 Hz
Spare parts list KRÄNZLE 1120 - 1150 T Motor
KRÄNZLE 1120 - 1150 T
30
Transmission
31
KRÄNZLE 1120 - 1150 T
No
De
sc
rip
tio
nQ
ty.
Ord
.-N
o
1G
ehäu
sepl
atte
143
.003
2Ö
ldic
htun
g 14
x 2
4 x
73
41.6
313
O-R
ing
83 x
21
43.0
394
Plu
nger
fede
r3
43.0
405
Fed
erdr
ucks
chei
be 1
4 m
m3
43.0
416
Plu
nger
14
mm
343
.005
7S
pren
grin
g 14
mm
341
.635
8Ta
umel
sche
ibe
12,0
° fü
r K1
120
141
.028
-12,
0Ta
umel
sche
ibe
9,25
° fü
r K1
150
230V
/ 50H
z1
41.0
28-9
,25
Taum
elsc
heib
e 9,
25°
für
K115
0 T
230V
/ 50H
z1
41.0
28-9
,25
Taum
elsc
heib
e 8,
0° fü
r K1
150
230V
/ 60H
z1
41.0
28-8
,0pl
ease
spe
cifiy
ang
le w
hen
orde
ring
10A
xial
-Rill
enku
gella
ger
3-te
ilig
143
.486
12In
nens
echs
kant
schr
aube
M 8
x 2
54
40.0
5313
Ver
schl
ußsc
hrau
be
M 1
8 x
1,5
141
.011
14O
-Rin
g 12
x 2
215
.005
115
Öls
chau
glas
142
.018
116
Ölv
ersc
hluß
schr
aube
rot
143
.437
17D
icht
ung
Öld
ecke
l1
44.5
01 1
18D
ecke
l Ö
lgeh
äuse
144
.501
219
Inne
nsec
hska
ntsc
hrau
be
M 5
x 1
24
41.0
19 4
Sp
are
pa
rts
list
KR
ÄN
ZL
E 1
12
0 -
11
50
T T
ran
smis
sio
n
32
Valve housing K 1120 T - K 1150 T
33
KRÄNZLE 1120 T - 1150 T
No
De
sc
rip
tio
nQ
ty.
Ord
.-N
oN
oD
esc
rip
tio
nQ
ty.
Ord
.-N
o
Sp
are
pa
rts
list
KR
ÄN
ZL
E 1
12
0 T
- 1
15
0 T
Va
lve
ho
usin
g
Re
p.-
kit
va
lve
s4
1.6
48
6x P
os. 4
, 12x
Pos
. 7
Re
p.-
kit
sle
eve
s4
3.0
60
3x P
os. 2
8; 3
x P
os. 2
9; 3
x P
os. 3
0, 3
x P
os. 3
2
Va
lve
ho
usi
ng
co
mp
l.4
4.5
31
Pos
. 1-2
5; P
os. 2
7-43
Gu
ide
pis
ton
wit
h s
ea
ls4
4.5
32
Pos
. 14;
Pos
. 15
Gu
ide
pis
ton
wit
h h
an
dw
he
el
44
.53
2 1
Pos
. 7; P
os. 1
4-25
1 V
entil
gehä
use
1 44
.523
2
Ven
tilst
opfe
n 5
41.0
11
3 V
entil
stop
fen
mit
R1/
4" IG
1
41.0
11 1
4
Ven
tile
(rot
) 6
41.6
12
5 D
icht
stop
fen
M 8
x 1
1
13.1
58
6 D
icht
stop
fen
M 1
0 x
1 1
43.0
43
7 O
-Rin
g 12
x 2
15
15
.005
1
8 O
-Rin
g 11
x 1
,5
2 12
.256
9
Ede
lsta
hlsi
tz
2 14
.118
10
S
iche
rung
srin
g 2
13.1
47
11
Ede
lsta
hlku
gel
8,5
mm
1
13.1
48
11.1
E
dels
tahl
kuge
l 10
,0 m
m
1 12
.122
12
E
dels
tahl
fede
r 1
14.1
19
13
Ver
schl
usss
chra
ube
1 14
.113
14
S
teue
rkol
ben
6 m
m fü
r A
Z
1 43
.044
15
P
arba
ks fü
r K
olbe
n 14
mm
1
14.1
23 1
16
P
arba
ks fü
r S
pind
el 6
mm
1
14.1
23 2
17
M
S-S
chei
be
1 43
.045
18
K
olbe
nfüh
rung
6 m
m
1 14
.130
1
19
Mut
ter
M 6
2
14.1
27 1
20
F
eder
sch
war
z fü
r A
Z-P
umpe
1
43.0
46
21
Fed
erdr
ucks
chei
be
1 43
.047
22
K
ugel
lage
r 1
43.0
48
23
Han
drad
M 6
für
AZ
-Pum
pe
1 43
.049
24
M
utte
r M
6 m
it S
W 8
1
43.0
10
25
Kap
pe fü
r H
andr
ad A
Z-P
umpe
1
43.0
50
26
Man
omet
er
1 15
.039
27
S
tütz
ring
3 43
.091
28
G
eweb
eman
sche
tte 1
4x24
x5
3 41
.613
1
29
Bac
krin
g 1
4 x
24
3 41
.614
30
O
-Rin
g 2
6 x
2 3
43.0
52
31
Leck
ager
ing
3 43
.053
32
M
ansc
hette
14
x 20
x 4
/2
3 43
.054
33
Z
wis
chen
ring
mit
Abs
tütz
ung
3 43
.055
34
R
ücks
chla
gfed
er
1 14
.120
1
35
Ver
schl
usss
topf
en fü
r K
ugel
rück
s.v.
1
44.5
24
36
Erm
etow
inke
l R1/
4"x8
1
40.1
79
42
Inne
nsec
hska
ntsc
hr.
M 8
x 2
5 2
40.0
53
43
Inne
nsec
hska
ntsc
hr.
M 8
x 4
0 2
43.0
59
44
Dic
htrin
g K
upfe
r 1
14.1
49
45
Sau
gans
chlu
ss
1 41
.016
46
W
asse
rfilt
er
1 41
.046
1
48
Gum
mi D
icht
ring
1 41
.047
1
49
Ste
ckku
pplu
ng
1 41
.047
2
50
O-R
ing
1 41
.047
3
52
O-R
ing
18 x
2
1 43
.446
34
Valve housing K 1120 - K 1150
35
KRÄNZLE 1120 - 1150S
pa
re p
art
s li
st K
RÄ
NZ
LE
11
20
- 1
15
0V
alv
e h
ou
sin
g No
De
sc
rip
tio
nQ
ty.
Ord
.-N
oN
oD
esc
rip
tio
nQ
ty.
Ord
.-N
o
1 Ve
ntilg
ehäu
se
1 44
.523
2
Vent
ilsto
pfen
5
41.0
11
3 Ve
ntils
topf
en m
it R
1/4"
IG
1 41
.011
1
4 Ve
ntile
(rot
) 6
41.6
12
5 D
icht
stop
fen
M 8
x 1
1
13.1
58
6 D
icht
stop
fen
M 1
0 x
1 1
43.0
43
7 O
-Rin
g 12
x 2
15
15
.005
1
8 O
-Rin
g 11
x 1
,5
2 12
.256
9
Edel
stah
lsitz
2
14.1
18
10
Sich
erun
gsrin
g 2
13.1
47
11
Edel
stah
lkug
el 8
,5 m
m
1 13
.148
11
.1
Ede
lsta
hlku
gel
10,0
mm
1
12.1
22
12
Edel
stah
lfede
r 1
14.1
19
13
Vers
chlu
ßsch
raub
e 1
14.1
13
14
Steu
erko
lben
6 m
m fü
r AZ
1 43
.044
15
Pa
rbak
s fü
r Kol
ben
14 m
m
1 14
.123
1
16
Parb
aks
für S
pind
el 6
mm
1
14.1
23 2
17
M
S-Sc
heib
e 1
43.0
45
18
Kolb
enfü
hrun
g 6
mm
1
14.1
30 1
19
M
utte
r M
6
2 14
.127
1
20
Fede
r sch
war
z fü
r AZ-
Pum
pe
1 43
.046
21
Fe
derd
ruck
sche
ibe
1 43
.047
22
Ku
gella
ger
1 43
.048
23
H
andr
ad M
6 fü
r AZ-
Pum
pe
1 43
.049
24
M
utte
r M
6 m
it SW
8
1 43
.010
25
Ka
ppe
für H
andr
ad A
Z-Pu
mpe
1
43.0
50
26
Man
omet
er
1 15
.039
27
St
ützr
ing
3 43
.091
28
G
eweb
eman
sche
tte 1
4x24
x5
3 41
.613
1
29
Back
ring
14
x 24
3
41.6
14
30
O-R
ing
26
x 2
3 43
.052
Re
p.-
kit
va
lve
s4
1.6
46x
Pos
. 4, 1
2x P
os. 7
Re
p.-
kit
sle
eve
s4
3.0
60
3x P
os. 2
8; 3
x P
os. 2
9; 3
x P
os. 3
0, 3
x P
os. 3
2
Va
lve
ho
usi
ng
co
mp
l.4
4.5
33
Pos
. 1-2
5; P
os. 2
7-43
Gu
ide
pis
ton
wit
h s
ea
ls4
4.5
32
Pos
. 14;
Pos
. 15
Gu
ide
pis
ton
wit
h h
an
dw
he
el
44
.53
2 1
Pos
. 7; P
os. 1
4-25
31
Leck
ager
ing
3 43
.053
32
M
ansc
hette
14
x 20
x 4
/2
3 43
.054
33
Zw
isch
enrin
g m
it Ab
stüt
zung
3
43.0
55
34
Rüc
ksch
lagf
eder
1
14.1
20 1
35
Au
sgan
gsst
. Inj
. ST3
0 M
22x1
,5
1 44
.544
incl
. 7, 2
x37,
2x3
8, 3
9, 4
0, 4
1 36
Ve
rsch
luss
topf
en 1
/4“
1 13
.181
37
Ve
rsch
luss
schr
aube
M10
x1
2 13
.385
38
O
-Rin
g 6x
1,5
2 13
.386
39
Sa
ugza
pfen
Sch
lauc
hans
chlu
ss
1 13
.236
40
Ed
elst
ahlk
ugel
5,5
mm
1
13.2
38
41
Edel
stah
lfede
r 1
13.2
39
42
Inne
nsec
hska
ntsc
hr.
M 8
x 2
5 2
40.0
53
43
Inne
nsec
hska
ntsc
hr.
M 8
x 4
0 2
43.0
59
44
Dic
htrin
g Ku
pfer
1
14.1
49
45
Saug
ansc
hlus
s 1
41.0
16
46
Was
serfi
lter
1 41
.046
1
48
Gum
mi D
icht
ring
1 41
.047
1
49
Stec
kkup
plun
g 1
41.0
47 2
50
O
-Rin
g 1
41.0
47 3
51
Al
umin
ium
-Dic
htrin
g 2
13.2
75
52
O-R
ing
18 x
2
1 43
.446
36
Hose drum
37
KRÄNZLE 1120 T - 1150 TS
pa
re p
art
s li
st K
RÄ
NZ
LE
11
20
T -
11
50
TH
ose
dru
m
No
De
sc
rip
tio
nQ
ty.
Ord
.-N
o
1S
chal
e gr
oß1
40.1
602
Sch
ale
klei
n1
40.1
613
Kni
cksc
hutz
140
.162
4A
ntrie
bsw
elle
144
.517
5K
urbe
l1
40.1
656
Lage
rklo
tz l
inks
144
.515
7La
gerk
lotz
rec
hts
144
.516
8D
rehg
elen
k1
40.1
679
Ach
se m
it W
asse
rfüh
rung
144
.518
10E
inga
ngsi
njek
tror
140
.169
11H
D-S
chla
uch
NW
6
15 m
140
.170
12S
chra
ube
M 6
x 1
61
40.1
71 1
13S
chra
ube
M 5
x 1
01
43.0
2114
Ans
chlu
ßro
hr E
rmet
o E
dels
tahl
144
.520
15P
arba
ks 1
6 m
m2
13.1
5916
O-R
ing
10 x
21
43.0
6817
Sic
heru
ngsr
ing
16
mm
140
.182
18S
chei
be
MS
16
x 2
4 x
21
40.1
8119
O-R
ing
6,6
8 x
1,78
140
.585
20S
iche
rung
srin
g 2
0 m
m1
40.1
7221
Kun
stst
offs
chra
ube
5,0
x 2
04
43.0
1822
Zah
nsch
eibe
6,4
140
.183
23S
chei
be D
IN90
21 6
,41
50.1
7425
Sau
gzap
fen
Sch
lauc
hans
chlu
ß1
13.2
3626
Ede
lsta
hlku
gel
5,5
mm
113
.238
27E
dels
tahl
fede
r1
13.2
3928
Che
mik
alie
nsau
gsch
lauc
h m
it F
ilter
115
.038
29O
-Rin
g 6
x 0
,82
40.1
77
38
Terminal strip
Weber-Unimat WT 22 - 55113,5A excess current release
Motor-Stator
Wiring diagram for KRÄNZLE K 1120 - K1150 T
Wiring diagram
C : 40µF ( 80 µF bei 110V / 60 Hz )braun = brownblau = blueschw = blackrt = redge = yellowgn = greenws = white
39
InspectionsThe machine must be inspected according to the “Guidelines for Liquid SprayDevices” at least once every 12 months by a qualified person, to ensure thatcontinued safe operation is guarateed. The results of the inspection are to berecorded in writing. This may be done in any form.
Accident preventionThe machine is designed for accidents to be impossible if used correctly.The operator is to be notified of the risk of injury from hot machine parts and thehigh pressure water jet. The “Guidelines for Liquid Spray Devices” must be com-plied with. (see page 14 and 15)
Oil change:
Check the oil level at the oil sight glass prior to each use.(Ensure horizontal position!) The oil level should be at the middle ofthe sight glass. With high atmospheric humidity and temperaturefluctuation there may be condensation (oil has a greyish colour);Then the oil must be changed.First oil change after approx 50 hours of operation. Thereafter, no more oil changeis required for the lifetime of the equipment. If it becomes necessary during repairs,or because the oil has a greyish colour to perform an oil change, then the oil sightglass should be opened and the oil emptied into a container. The oil must be caughtin a container and disposed of in a responsible, legal manner.New oil: 0.25 l - Motor oil: W 15/40
Oil leakIn the event of an oil leak contact customer service (dealer) immediately. (damageto environment or transmission)
General rules
40
I. Kränzle GmbHElpke 9733605 Bielefeld
HochdruckreinigerHigh-pressure-cleaners
Nettoyeurs À Haute Pression
(Managing Director)
We hereby declare,that the high-pressure models:
(techn. documentation available from):
comply with the following guidelines andspecifications and their amendments forhigh-pressure cleaners:
Sound power level measured:guaranteed:
Applied specifications andstandards:
EC declaration of conformity
Bielefeld, den 08.09.05
Kränzle 1120 - 1150Kränzle 1120 T - 1150 T
Manfred Bauer, Fa. Josef KränzleRudolf-Diesel-Str. 20, 89257 Illertissen
Machine guideline 89/392/EECLow voltage guideline 73/23 EECSpecification for electromagneticcompatibility 89/336 EECOutdoor noise directive 2000/14/EC,Art. 13, High-pressure water jet machinesAppendix 3, part B, chapter 27
91 dB (A)93 dB (A)
EN 60 335-2-79 / A1:2001EN 55 014-1 / A2:2002EN 55 014-2 / A1:2001EN 61 000-3-2 / A14:2000EN 61 000-3-3 / A1:2001
41
Notes
Warranty This warranty covers material and/or workmanship related defects only and does not extend to ordinary wear. Machine must be operated according to enclosed operating instructions which are part of present warranty conditions. All products sold directly to private customers are warrantied for a period of 24 months, whereas the warranty period for industrial purchases is limited to 12 months. In case of any warranty claims, please have your HP cleaner together with accessories and your purchase document ready and contact your nearest dealer or authorized service point which can also be looked up in the internet at www.kraenzle.com . Warranty is void in case of attempts to modify any of the safety devices or in the event of exceeding temperature or rpm limits - this also applies to undervoltage, low water and/or polluted water. Gauge, nozzle, valves, sealing gaskets, high pressure hose and spray equipment are considered wear parts and do not fall under this warranty.
42
Notes
43
Notes
Reprint only allowed with the authorization of
As date of 08.09.2005
Ord
er n
°: 30
236
1
R