hhe report no. heta-2000-0332-2827, niosh …...heta 2000–0332–2827 niosh exposure assessment of...

HETA 2000–0332–2827NIOSH Exposure Assessment ofCellulose Insulation Applicators

Robert E. McCleery, MSPHJoel McCullough, MD

Ronald M. Hall, MSJoseph E. Fernback

This Health Hazard Evaluation (HHE) report and any recommendations made herein are for the specific facility evaluated and may not be universally applicable. Any recommendations made are not to be considered as final statements of NIOSH policy or of any agency or individual involved. Additional HHE reports are available at http://www.cdc.gov/niosh/hhe/reports



This Health Hazard Evaluation (HHE) report and any recommendations made herein are for the specific facility evaluated and may not be universally applicable. Any recommendations made are not to be considered as final statements of NIOSH policy or of any agency or individual involved.


applicable. Any recommendations made are not to be considered as final statements of NIOSH policy or of any agency or individual involved. Additional HHE reports are available at http://www.cdc.gov/niosh/hhe/reports

http://www.cdc.gov/niosh/hhe/reports/

ii

PREFACE

The Hazard Evaluations and Technical Assistance Branch (HETAB) of the National Institute forOccupational Safety and Health (NIOSH) conducts field investigations of possible health hazards in theworkplace. These investigations are conducted under the authority of Section 20(a)(6) of the OccupationalSafety and Health (OSHA) Act of 1970, 29 U.S.C. 669(a)(6) which authorizes the Secretary of Health andHuman Services, following a written request from any employer or authorized representative of employees,to determine whether any substance normally found in the place of employment has potentially toxic effectsin such concentrations as used or found.

HETAB also provides, upon request, technical and consultative assistance to Federal, State, and localagencies; labor; industry; and other groups or individuals to control occupational health hazards and to preventrelated trauma and disease. Mention of company names or products does not constitute endorsement byNIOSH.

ACKNOWLEDGMENTS AND AVAILABILITY OF REPORT

This report was prepared by Robert E. McCleery, MSPH, Ronald M. Hall, MS, and Joel McCullough, MD,of HETAB in the Division of Surveillance, Hazard Evaluations and Field Studies (DSHEFS); and Joseph E.Fernback of the Chemical Exposure and Monitoring Branch (CEMB) in the Division of Applied Researchand Technology (DART). Field assistance was provided by Bruce Bernard, Leo Blade, Nancy Burton,Krystyn Bussa, Calvin Cook, Joshua Harney, Brad King, Gregory Kinnes, Ali Lopez, Kenneth Martinez, DinoMattorano, and Kevin Roegner. Analytical support was provided by Mark Millson of DART, and Data ChemLaboratories, Salt Lake City, Utah. Statistical support was provided by Charles A. Mueller of DSHEFS.Desktop publishing was performed by Robin Smith and Pat Lovell. Review and preparation for printing wereperformed by Penny Arthur.

Copies of this report have been sent to employee and management representatives at the participatingcompanies and the OSHA Regional Office. This report is not copyrighted and may be freely reproduced.Single copies of this report will be available for a period of three years from the date of this report. Toexpedite your request, include a self–addressed mailing label along with your written request to:

NIOSH Publications Office4676 Columbia ParkwayCincinnati, Ohio 45226

800–356–4674

After this time, copies may be purchased from the National Technical Information Service (NTIS) at5825 Port Royal Road, Springfield, Virginia 22161. Information regarding the NTIS stock number may beobtained from the NIOSH Publications Office at the Cincinnati address.

iii

For the purpose of informing affected employees, copies of this report shall be posted by theemployer in a prominent place accessible to the employees for a period of 30 calendar days.

Highlights of the NIOSH Health Hazard Evaluations

NIOSH Exposure Assessment of Cellulose Insulation Applicators

Cellulose insulation (CI) was nominated to the National Toxicology Program (NTP) for a comprehensivetoxicological evaluation. The NIOSH was presented with an opportunity to assist in the evaluation of CI byconducting the exposure assessment through an interagency agreement with the National Institute ofEnvironmental Health Sciences/NTP.

What NIOSH Did

# We took air samples for total dust and respirabledust, and characterized any fibers in the dust.

# The fibers in the dust were examined to determinethe type of fiber and its length. We also measuredthe concentration of fibers on the sample filter.

# We handed out a medical history questionnaire toemployees. In addition, we recorded any short–termhealth symptoms and conducted an employeebreathing test to measure the amount of air exhaledin one second by blowing into a tube duringpre–shift, mid–day, and post–shift.

# We talked to employees about their jobs, the CIapplication process, and their concerns with thisprocess.

What NIOSH Found

# There is potential for exposures to total dustgreater than the OSHA limit during all CI applicationoperations.

# Respirable dust levels were typically low during allCI operations.

# The CI dust contains mostly particles, not fibers.Most of the fibers in the dust are large and cannottravel into the lower areas of the lung.

# Applying moistened CI into attics reduces theamount of CI dust in the air.

What Managers Can Do

# Require (at a minimum) NIOSH approved, N95particulate filtering respirators be worn during CIactivities.

# Create a respiratory protection program based onOSHA Respiratory Protection Standard, 29, Code ofFederal Regulations 1910.134.

# If possible, use a moistening system for attic CIapplication to reduce CI dust.

# Use engineering controls (examples are given inthe report) in the hopper area to reduc e exposuresto hopper operators.

# Make sure areas of CI use are cleaned on aregular basis to reduce unnecessary dust exposure.

What the Employees Can Do

# Wear, at a minimum, a NIOSH approved, N95particulate filtering respirator during all CI relatedoperations.

# Replace these respirators when dirty or damaged.

# In attics, apply CI away from body and if possible,reduce amount of time in corners.

# Wash your hands, if possible, before eating ordrinking.

# Clean–up hopper area after your shift iscompleted to minimize unnecessary generation of CIdust.

iv

CDCCENTERS FOR DISEASE CONTROL

AND PREVENTION

What To Do For More Information:We encourage you to read the full report. If you

would like a copy, either ask your health and safetyrepresentative to make you a copy or call

1-513-841-4252 and ask for HETA Report # 2000–0332–2827

HHE Health Hazard Evaluation Report 2000–0322–2827NIOSH Exposure Assessment ofCellulose Insulation Applicators

March 2001

Robert E. McCleery, MSPHJoel McCullough, MD

Ronald M. Hall, MSJoseph E. Fernback

SUMMARY

In July 1994, cellulose insulation (CI) was nominated to the National Toxicology Program (NTP) for acomprehensive toxicological evaluation. The evaluation consisted of two components: (1) a bulk analyticalcharacterization of CI and (2) an exposure assessment of U.S. contractors applying the CI in residential andcommercial buildings. The National Institute for Occupational Safety and Health (NIOSH) was presentedwith an opportunity to assist in the evaluation of CI by conducting the exposure assessment through aninteragency agreement with the National Institute of Environmental Health Sciences/NTP.

NIOSH conducted the CI exposure assessment, which included a medical component, with 10 contractorslocated across the United States. During each contractor site visit, air samples were collected for total dust,respirable dust, and for scanning electron microscopy (SEM) analysis to characterize any fibers in the dust.The CI installer and hopper operator each had two SEM air samples collected for each day of CI activities.Bulk samples of the CI were collected and analyzed for metals, boron, and sulfate content. Real–time andvideo exposure monitoring were also conducted to further characterize the CI dust and workers’ exposures.

For the 10 contractor site visits, 175 personal breathing zone (PBZ) total dust, 106 area total dust, and 90 arearespirable dust air samples were collected during CI related activities. There were 26 employees with totaldust eight–hour time–weighted averages (8–hour TWAs) exceeding the Occupational Safety and HealthAdministration (OSHA) Permissible Exposure Limit (PEL) of 15 milligrams per cubic meter (mg/m3) and42 exceeding the American Conference of Governmental Industrial Hygienists (ACGIH) Threshold LimitValue (TLV) of 10 mg/m3. Respirable dust air sampling and real–time monitoring with particle sizediscrimination indicated low levels of respirable dust generation. The SEM analyses revealed that fibers wereon average 28 micrometers (µm) in length and ranged from 5 µm to 150 µm. CI installers’ PBZ samples andarea air samples for total dust were significantly higher for dry attic applications than wet attic applications(p < 0.01). Respirable dust air samples collected in the attic area indicated a significantly higher concentration

v

for dry applications than wet applications (p < 0.01). The hopper operators’ total dust exposures weresignificantly higher during wet wall/ceiling applications than dry wall/ceiling applications (p = 0.02). Analysisof variance (ANOVA) tests evaluating exposure concentrations revealed that total dust air samples collectedin the PBZ of workers (CI installer in attics, CI installer in walls, hopper operator during attic applications,and hopper operator during walls/ceiling applications) varied significantly during dry applications (p < 0.01).The respirable dust air samples collected in various areas (attic area, hopper area during attic applications,and hopper area during walls/ceiling applications) differed significantly during dry applications (p = 0.03).

Twenty–three workers participated in the medical phase of the investigation. The workers completed amedical and work history questionnaire, performed serial peak flow tests, and completed multiple acutesymptom surveys. The medical questionnaires indicated respiratory, nasal, and skin symptoms that employeesattributed to CI exposure. The most common symptoms reported while working with CI included nasalsymptoms (35%), eye symptoms (35%), and morning phlegm production (25%). There was a temporalassociation between CI exposure and eye symptoms. There is little evidence of lower respiratory systemhealth conditions associated with CI exposure.

Based on the air sample data collected from the 10 contractor site visits, NIOSH investigators concludethat there is potential for overexposure to cellulose insulation (CI). Employees in virtually all CIapplication activities were exposed to total dust levels which exceeded the OSHA 8–hour TWA of15 mg/m3. CI installers’ PBZ total dust samples and area air samples for total and respirable dust weresignificantly higher for dry attic applications than wet attic applications. Eye symptoms were temporallyassociated with CI exposure. There is little evidence of lower respiratory tract health conditionsassociated with CI exposure. Suggestions to improve the health and safety of employees in this industry,through the use of engineering controls and personal protective equipment (i.e., respirators), are presentedin the Recommendations section of this report.

Keywords: SIC Code 1742 (Plastering, Drywall, Acoustical, and Insulation work [Insulationbuildings–contractors]); cellulose insulation, recycled, newspaper, boric acid, fire–proofing, residential, attic,serial peak flow, respiratory, skin, eye.

TABLE OF CONTENTS

Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

Acknowledgments and Availability of Report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

Highlights of the HHE Report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Background . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Process Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Attic Cellulose Insulation Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Wall Cellulose Insulation Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Dry Cellulose Insulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Wet Cellulose Insulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Cellulose Insulation Hoppers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Conduct of Field Studies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Site Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Sampling Protocol Development . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Sample Collection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3In–depth Surveys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Industrial Hygiene Sampling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Medical Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Statistical Strategy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Evaluation Criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Cellulose Insulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Medical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Boric Acid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Borax . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Comprehensive Project Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Personal Protective Equipment (PPE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Cellulose Insulation Statistical Analyses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Medical Evaluation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Individual Contractor Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Contractor 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Contractor 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Contractor 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Contractor 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Contractor 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Contractor 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Contractor 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Contractor 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Contractor 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Contractor 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Discussion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Application of Dry Cellulose Insulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Application of Wet Cellulose Insulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Fiber Characterization of Cellulose Insulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Bulk Samples of CI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Real–time Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Video Exposure Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Engineering Controls, Administrative Controls, and Personal Protective Equipment . . . . . . . . . . . . . . 23Medical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Conclusions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Appendices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32A. Contractor 1–10 Total and Respirable Dust Sampling Results . . . . . . . . . . . . . . . . . . . . . . . . . . 32B. Scanning Electron Microscopy Air Sampling Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55C. Bulk Cellulose Insulation Material Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64D. Real–time Particulate Measurement Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68E. Video Exposure Monitoring Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70F. Pictures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72G. Medical History Questionnaire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75H. Acute Symptom Survey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Health Hazard Evaluation Report No. 2000–0332–2827 Page 1

INTRODUCTION

Cellulose insulation (CI) was nominated to theNational Toxicology Program (NTP) for acomprehensive toxicological evaluation. Theevaluation consisted of two components: (1) abulk analytical characterization of CI and (2) anexposure assessment of U.S. contractors installingCI in residential and commercial buildings. TheNational Institute for Occupational Safety andHealth (NIOSH) was presented with anopportunity to assist in the evaluation of CI byconducting the exposure assessment through aninteragency agreement with the National Instituteof Environmental Health Sciences/NTP.

NIOSH conducted the CI exposure assessmentwith 10 contractors located across the UnitedStates, after contacting various contractors,discussing NIOSH and the nature of the researchproject, and receiving support by contractormanagement. NIOSH investigators conducted aninitial environmental protocol developmentinvestigation in Colorado in January 1998. Basedupon the initial findings, the NIOSH investigatorsdetermined the sampling methods needed tocharacterize CI applicators exposures togenerated CI dust. This report summarizes theNIOSH evaluation and provides recommendationsfor improving occupational health and safety of CIapplicators.

BACKGROUND

CI is manufac tured primarily from recyclednewspapers and other recovered paper fibers.Fire retardants such as boric acid, borax, othersimilar borates, or ammonium sulfate are added.Some of the cellulose products contain gypsum orstarch. “Stabilized Cellulose” is a form of CI thathas a small amount of water added and is appliedin attics. This type of insulation has an adhesiveadded, so that with the addition of water, the

applied depth of the CI is stabilized. CI wall sprayalso has a small amount of water added to assistin securing CI between wall studs. (CI withwater added is listed as “wet” CI in this report.It should be emphasized that only a smallamount of water is added and that the CI isonly moist to the touch.) There areapproximately 30–35 companies currentlymanufacturing CI in 50–60 plants across the U.S.1

Any type of CI must comply with certain federalagencies and industrial standards. These include,but are not limited to: the Consumer ProductsSafety Commission, Interim Safety Standard forCellulose Insulation2; the American Society forTesting and Materials (ASTM) C739–97,Standard Specification for Cellulosic Fiber(Wood–Base) Loose–Fill Thermal Insulation3; andASTM C1149–97, Standard Specification forSelf–Supported Spray Applied Cellulosic ThermalInsulation.4

On two different occasions NIOSH has evaluatedCI exposures of employees weatherizing homes.5,6

The first evaluation involved a weatherizationcompany that applied CI into an attic and outsidewal ls . The 8–hour t ime–weighteda v e r a g e s ( T WAs) were as follows:20.6 milligrams per cubic meter (mg/m3) and34.5 mg/m3 for the CI installers in the attic,5.2 mg/m3 for the installer of CI in outside walls,and 0.9 mg/m3 and 4.3 mg/m3 for the hopperoperator. Employees wore NIOSH approvedhalf–mask respirators with cartridges for dusts,fume, and mist while blowing CI into attics anddisposable dust masks while loading CI into thehopper. The second evaluation was anotherweatherization program involved with reducing theenergy consumption of low–income housing.Personal breathing zone (PBZ) air samples werecollected for total dust during CI applicationactivities and resulted in the following air sampleconcentrations: 4.6 mg/m3 for the employeeapplying CI into walls, 13.8 mg/m3 for the

Health Hazard Evaluation Report No. 2000–0332–2827

employee trying to get the hopper running,2.2 mg/m3 for the employee also working on thehopper, 4.3 mg/m3 for the hopper operator, and$40.8 mg/m3 for the CI installer in the attic. Allthe employees wore half–face respirators withhigh efficiency particulate air (HEPA)/ organicvapor cartridges.

PROCESS DESCRIPTION

Attic Cellulose InsulationApplication

CI application in attics begins with atticpreparation (See Appendix F – Picture 1). Atticpreparation may be performed by a separate crewor by the same crew that conducts the CIapplication. Fiberglass batting is laid over the topof pipes and recess lights, barriers are installed inthe attic soffit area to prevent CI from passingthrough the attic to the outside, and other activitiesare performed depending upon the attic. Anapplication hose is brought up to the attic throughan attic access panel. CI is then applied to thespecified R–value (resistance to heat flow).7 CIcan be applied dry or wet. When the CI is appliedwet, there is a misting device in–line with theapplication hose close to the hopper area.

Wall Cellulose InsulationApplication

Dry Cellulose Insulation

Dry application of CI into existing walls beginswith holes being drilled into the inside or outsidewall between wall studs. CI is then appliedthrough a smaller diameter hose (1–2 inches ["])than is used with the other methods of CIapplication. The CI is applied and the hose ispulled out of the wall as pressure builds (otherwise

the wallboard could release from the wall) . Aplug is then put into the drilled hole to keep the CIin the wall space. The plugs can be manydifferent types of materials.

Wet Cellulose Insulation

For wet CI application into newly constructedwalls, a misting device is placed at the end of theapplication hose. As the CI passes through thehose, the water moistens the CI and the surface ofthe wall to assist in adherence. The CI ismoistened enough to stick into the wall withoutfalling out of the wall space (See Appendix F –Picture 5). Excess material protruding out frombetween the wall studs is removed with an electricroller. The excess material is then vacuumeddirectly into the hopper or shoveled into trash bagsor cans and put into the hopper for reuse. In someareas of the country, polyethylene sheeting wasstapled to the wall studs of exterior walls after theCI application to serve as a vapor barrier and tokeep the CI in the wall space. Interior walls withno wallboard backing material, as is found forexterior walls, have a white cloth material(resembling cheese cloth) stapled to the wallstuds. CI is then applied to that surface and theprocess proceeds as previously described. Somecontractors will then staple a wire mesh to thewalls studs to keep the CI from falling out of thewall space.

Cellulose Insulation Hoppers

Hoppers used for CI applications come in manydifferent shapes and sizes. There were two basictypes observed during this project: those withrecycling capability built in and those without. Thehoppers with their own recycling capability arelarger and have more advanced operation controls(setting units in revolutions per minute [rpm] andpounds per square inch [psi]). The smallerhoppers use control plates to set the amount ofmaterial being fed through the hopper to the hose


and have a dial for the amount of air being sentthrough the hose. Attic applications typically useno hopper plates and are set for full air. CIapplication into existing walls will use less air andplates to reduce the amount of material.

CONDUCT OF FIELD

STUDIES

Site Selection

Site selection and the number of site visits wasbased on (1) having at least one contractor fromeach section of the country (i.e., Northwest,Midwest, Southeast, etc.), (2) the number ofconsenting contractors, (3) the ability to providewall and attic CI application sites during surveytime period, and (4) appropriate sample size forvarious statistical comparisons. Before NIOSHpersonnel arrived for the survey, each contractorwas contacted to obtain their consent and amutually agreeable date for the survey, and todiscuss the planned sampling efforts and details oftheir operation. After each site visit, eachcontractor received a report which includedsections on sampling methods, discussion of jobsites sampled, air sample results, conclusions, andrecommendations.

Sampling ProtocolDevelopment

The first contractor survey was conducted over athree–day period to develop a sampling protocolfor the rest of the project. The survey involvedPBZ and area air sampling, real–time monitoringusing a portable dust monitor (PDM), and videoexposure monitoring (VEM) during CI applicationactivities. The survey objective was to observethe CI application process, to work with differentparameters of the various sampling methods todetermine the most effective set–up, and to

facilitate discussion of the process with theemployees conducting the application.

Sample Collection

Samples collected at each application site werefocused in two areas: around the CI installer andaround the employee dumping bags of CI into thehopper. Area and PBZ air samples for total andrespirable dust were collected in both areas andsubsequently analyzed gravimetrically.Additionally, each sample was analyzed for boronand sulfate content. Two PBZ, scanning electronmicroscopy (SEM) samples were collected ineach of the two areas. The sampling time foreach sample depended upon the extent of materialloading on the filters. Real–time monitoring oftotal and respirable dust was conducted during CIapplications when the opportunity presented itself.

Employee duties throughout the day were highlyvariable and no specific task lasted eight hours.Therefore, the air sampling protocol was designedto collect task–based (i.e., short–term) samplesfor each worker involved with specific CIactivities for the duration of each specific worktask. Analytical results were used to calculateboth total and respirable dust concentrations foreach task–based sample and 8–hour TWAexposures for each worker. The 8–hour TWAsincluded all task–based samples for the entirework–shift by each specific worker. Area 8–hourTWA results are based on the compiled exposureresults in that specific area for the entire taskperiod. Calculated area 8–hour TWAconcentrations are intended to be representationsof potential exposure. In calculating the 8–hourTWAs, time periods of non–involvement withCI–related activities were not sampled andconsidered to be a zero exposure.

In–depth Surveys


Four in–depth surveys (including VEM or returnvisit for further evaluation) were conducted. Twoof these involved the use of VEM along with airsampling, PDM measurements, and the medicalevaluation. VEM was conducted inside the atticwith the CI installer and inside the truck with thehopper operator during those CI applications. Theother two surveys involved return visits to furtherevaluate the CI application process due toapplication system change. One contractorchanged from a dry to a moistened CI applicationsystem. The second contractor used their originalmoistening application system not used during theinitial survey. In this case, the return survey wasto evaluate the contractor’s usual CI applicationoperations.

Methods

Industrial Hygiene Sampling

Total and Respirable Dust Sampling

Area and PBZ air samples for total dust werecollected on tared 37–millimeter (mm) diameter,5–micrometer (µm) pore size polyvinylchloride (PVC) filters, at a calibrated flow rate of1.0 liter per minute (lpm). The filters weregravimetrically analyzed (filter weight) accordingto NIOSH Method 0500.8 Area air samples forrespirable dust were collected with tared 37–mmdiameter, 5–µm PVC filters in line with a 10–mmcyclone at a calibrated flow rate of 1.7 lpm. Thefilters were gravimetrically analyzed according toNIOSH Method 0600.8 The analytical limit ofdetection (LOD) for the total and respirable dustfilters were 0.08 milligrams (mg) and 0.02 mg,respectively, which is equivalent to a minimumdetectable concentration (MDC) of 0.8 mg/m3 and0.2 mg/m3, respectively, assuming a samplevolume of 100 liters.

Scanning Electron Microscopy (SEM)Sampling

PBZ air samples of the CI dust were collectedusing a modified version of NIOSH Method 7402.8

Samples were collected using a 25–mm diametercassette with an electrically conductive extensioncowl, 0.8 µm pore size polycarbonate filters, at acalibrated flow rate of 1.0 lpm. The filter wasanalyzed by SEM for fiber count, fiber size, andfiber characteristics (cellulose, fiberglass, others).Analyses were conducted in a NIOSH laboratory,using the SEM in the Division of AppliedResearch and Technology (DART). The finalanalytical protocol used was as follows:

1. The samples were first given a conductivecarbon coat to minimize fiber charging. This alsoimproved the secondary electron images.

2. The prepared sample was placed in theinstrument sample holder.

3. The samples were analyzed using a secondaryelectron detector, which was adjusted to amagnification of 1,200X, and the center of thefilter was found using the X–Y manipulators.Fields were examined at regular intervals along atraverse in one direction. Fibers were counted ineach field using the "A" rules. Based uponmorphology, cellulose and other fiber types weredistinguished and the relative proportion of fibrousto non–fibrous material in the field was recorded.

4. A minimum of 40 fields were counted. If theedge of the filters was encountered before40 fields were analyzed, a new traverse in anotherdirection was begun from the center of the filter.

5. The actual analysis was conducted on theimage analyzer which had greater image resolutionthan the SEM screen. At least two fields werecaptured and saved on disk for archival andpresentation purposes.

6. The fibers were sized by comparison to acalibrated, overlain micron bar.


Bulk Material Sampling

Bulk samples of CI were collected from eachcontractor and analyzed by two methods. Thefirst method was a water extraction for boron andsulfate content. The second method was NIOSHMethod 7300,8 analyzing for boron, sulfate, andother elemental constituents. These methodsanalyzed for the following metals: aluminum (Al),arsenic (As), barium (Ba), beryllium (Be),calcium (Ca), cadmium (Cd), cobalt (Co),chromium (Cr), copper (Cu), iron (Fe), lithium (Li),magnes ium (Mg) , manganese (Mn) ,molybdenum (Mo), nickel (Ni), lead (Pb),phosphorus (P), platinum (Pt), selenium (Se),silver (Ag), sodium (Na), tellurium (Te),thallium (Tl), titanium (Ti), vanadium (V),yttrium (Y), zinc (Zn), and zirconium (Zr).Samples were analyzed for both methods using aninductively coupled plasma emission spectrometer.

Particle Count and Sizing

Real–time sampling was conducted to monitor theparticulates generated by distinct events during CIapplication activities in the attics and aroundhoppers. The Grimm Model 1.105 Dust Monitor(Labortechnik GmbH & CoKG, Ainring,Germany) was used to collect the real–time data.9

This PDM is a light scattering aerosolspectrometer designed for real–time particulatemeasurement with particle size discrimination.Eight channels collect count information forparticle sizes greater than 0.75, 1, 2, 3.5, 5, 7.5, 10,and 15 µm. For each operation, data wereintegrated for 1 minute (min) and storedsequentially on the Grimm data card over theentire time period. This particle count and sizeinformation was then downloaded to a laptopcomputer. Start and stop times for distinct eventswere also recorded.

The mass distr ibution of particles is reported as aconcentration in micrograms of particulate per

cubic meter of air (µg/m3). Particles are sizedbased upon the amount of light scattered byindividual particles. The monitor operates at aflow rate of 1.2 lpm. Estimates were made of themass median aerodynamic diameter (MMAD) andt h e a s s o c i a t e d g e o m e t r i c s t a n d a r ddeviation (GSD) based on the integrated particlesize discrimination provided by the instrument.The MMAD is the mid–point of theaerodynamic size distribution where half theparticles are larger and half are smaller. A CIdensity correction factor for the PDM was appliedduring data analysis. The density correction factoris the ratio of an integrated total dust sample to theindicated instrument total dust weight of the CIsampled. The conversion factors were used toadjust the instrument concentration values.

Video Exposure Monitoring (VEM)

Real–time particulate sampling, coupled with videorecording, was performed during two surveys toevaluate worker exposures. VEM was typicallyconducted concurrently during both attic CIapplication and hopper loading operations. Theobjective of VEM during CI related activities is toobserve the work practices of the CI installer andthe hopper operator and their associated total dustexposures. The VEM may indicate certain workpractices that can increase or reduce theconcentration of dust in the air.

During CI application activities, a Hand–heldAerosol Monitor (HAM) (PPM Inc., Knoxville,Tennessee) was used to measure PBZ relative aircontaminant concentrations. The HAM operatesby continuously drawing aerosols through anilluminated sensing volume and detecting theamount of light scattered by all the particles in thatvolume.10 The analog output of the HAM isrecorded by a data logger. The informationcollected on the data logger is downloaded to acomputer and converted into a spreadsheet foranalysis. The HAM was operated on the


0–200 volt scale during monitored activities in theattic and in the truck with the hopper.

VEM can be used to identify sources of workerexposure to air contaminants and to addressquestions such as: How does exposure varyamong the components of a job, What are theshortcomings of a control, and How quickly doesthe air contamination decay once an operation hasstopped?11,12 While air concentrations are beingmeasured with the HAM, workplace activities arerecorded on videotape. The analog output fromdirect reading instruments can be overlaid on avideo recording as a moving bar that has a heightproportional to the air contaminant concentration(See Appendix F – Picture 6 for example offinished product). This technique shows howworker exposures are related to work activities,and it permits control recommendations that arefocused upon actual exposure sources.

Medical Monitoring

Health Assessment of Symptoms andLung Function

NIOSH investigators recruited available workersperforming CI application at each work site. Theworkers were asked to complete aself–administered questionnaire, perform serialpeak flow tests, and complete repeated acutesymptoms survey.

Questionnaires:

A modified version of the American ThoracicS o c i e t y ( AT S ) s t a n d a r d i z e dquestionnaire (Appendix G) was administered toall participants to obtain the prevalence of chronicrespiratory, eye, nose, throat, and skin symptoms.Also, information concerning smoking history andwork history was solicited. This questionnairetook approximately 10–15 minutes to complete. Ina d d i t i o n , a s h o r t a c u t e s y m p t o msurvey (Appendix H) was periodically

administered by NIOSH investigators to studyparticipants before and after each work shift,2 times during the work shift, and at bedtime(self–administered) for a total of 5 data collectionperiods per day. Peak expiratory flow rate (seebelow) was measured at the same times the acutesymptoms surveys were completed.

Peak flow measurement:

NIOSH invest igators obtained ser ia ldeterminations of the peak expiratory flowrate (PEFR) using Wright portable flow meters.Peak flow refers to the amount of air in liters perminute that can be blown through the flow meterin one sharp breath. PEFR was measuredc oncomitantly with the acute symptom surveys(5 times per day from 1 to 4 days). PEFR wasmeasured pre–shift, 3 times during the shift, and atbedtime. The participants were instructed in theproper use of the portable meters. Threeexhalations were to be recorded each session, andthe maximum of the three was accepted as thePEFR determination. A participant wasconsidered to have significant bronchial lability ifthe amplitude percent mean ([maximum –minimum]/ mean) PEFR was greater than 20%.13

Statistical Strategy

Individual air sample concentrations for total andrespirable dust were compiled into a statisticalanalysis system (SAS) database. The data werearranged and grouped according to the type ofsample, PBZ or area, and type of CI application.Concentration data were analyzed to compare CIdust concentrations during wet and dry CIapplications. T–tests were used to accept orreject a null hypothesis of no significant differencein wet and dry concentrations. Statisticalsignificance was set at a level of 0.05.Additionally, all employee tasks and theirrespective air sample concentrations during eitherwet or dry CI applications were groupedseparately and analyzed to compare exposure


potential. An analysis of variance (ANOVA) wasused to accept or reject a null hypothesis of nosignificant difference in employees exposures.Statistical significance was set at a level of 0.05.

EVALUATION CRITERIA

As a guide to the evaluation of the hazards posedby workplace exposures, NIOSH field staffemploy environmental evaluation criteria for theassessment of a number of chemical and physicalagents. These criteria are intended to suggestlevels of exposure to which most workers may beexposed up to 10 hours per day, 40 hours perweek for a working lifetime without experiencingadverse health effects. It is, however, importantto note that not all workers will be protected fromadverse health effects even though theirexposures are maintained below these levels. Asmall percentage may experience adverse healtheffects because of individual susceptibility, apre–existing medical condition, and/or ahypersensitivity (allergy). In addition, somehazardous substances may act in combination withother workplace exposures, the generalenvironment, or with medications or personalhabits of the worker to produce health effectseven if the occupational exposures are controlledat the level set by the criterion. These combinedeffects are often not considered in the evaluationcriteria. Also, some substances are absorbed bydirect contact with the skin and mucousmembranes, and thus potentially increases theoverall exposure. Finally, evaluation criteria maychange over the years as new information on thetoxic effects of an agent become available.

The primary sources of environmental evaluationcriteria for the workplace are: (1) NIOSHRecommended Exposure Limits (RELs),14 (2) theAmerican Conference of Governmental IndustrialHygienists’ (ACGIH®) Threshold LimitValues (TLVs®),15 and (3) the U.S. Departmentof Labor, Occupational Safety and Health

Administration (OSHA) Permissible ExposureLimits (PELs).16 Employers are encouraged tofollow the OSHA limits, the NIOSH RELs, theACGIH TLVs, or whichever are the moreprotective criterion.

OSHA requires an employer to furnish employeesa place of employment that is free fromrecognized hazards that are causing or are likely tocause death or serious physical harm[Occupational Safety and Health Act of 1970,Public Law 95–596, sec. 5(a)(1)]. Thus,employers should understand that not all hazardouschemicals have specific OSHA exposure limitssuch as PELs and short–term exposurelimits (STELs). An employer is still required byOSHA to protect their employees from hazards,even in the absence of a specific OSHA PEL.

A TWA exposure refers to the average airborneconcentration of a substance during a normal 8–to 10–hour workday. Some substances haverecommended STEL or ceiling values which areintended to supplement the TWA where there arerecognized toxic effects from higher exposuresover the short–term.

Cellulose Insulation

There is a limited amount of published CIexposure or toxicological data. Availableinformation is largely based on the hazardsassociated with wood and its organic constituentsin the paper production industry, and generatedwood dust in occupations such as carpentry.

Environmental

CI is considered a “nuisance” dust and isclassified by ACGIH as particulate not otherwiseclassified (PNOC) or by OSHA as particulate nototherwise regulated (PNOR). Nuisance dustshave been referred to as dusts that have littleadverse effect on the lungs and, when maintained


under reasonable control, do not result insignificant organic disease or toxic effect.However, in sufficient quantities any dust will elicitsome cellular response in the lung. Thelung–tissue reaction caused by the inhalation ofPNOCs has the following characteristics: (1) thearchitecture of the air spaces remains intact; (2)collagen (“scar tissue”) is not synthesized to asignificant extent; and (3) the tissue reaction ispotentially reversible.17

PNOCs in extreme concentrations in theworkplace air may cause the following: a seriousreduction in visibility; unpleasant deposits in theeyes, ears, and nasal passages; or contribute toinjury of the skin or mucous membranes bychemical or mechanical action per se, or byrigorous skin cleansing procedures necessary fortheir removal.17

The OSHA PEL for PNORs is 15 mg/m3 for totaldust and 5 mg/m3 for respirable dust. Although aNIOSH REL for particulates has not beenestablished, after reviewing available publishedliterature, NIOSH provided comments to OSHAon August 1, 1988, regarding the “Proposed Ruleon Air Contaminants” (29 CFR 1910, Docket No.H–020). In these comments, NIOSH questionedwhether the proposed OSHA PEL (as an 8–hourTWA) of 10 mg/m3 for PNORs (defined as totaldust in this report) was adequate to protectworkers from recognized health hazards.14

ACGIH recommends a total dust, 8–hourTLV–TWA of 10 mg/m3 for inhalable PNOCscontaining no asbestos and <1% crystalline silica;and 3 mg/m3 for respirable dust.15 For substances,such as PNOC, without a STEL (a 15 minuteTWA, which can not be exceeded at any timeduring the workday), ACGIH recommends aconcept called an excursion limit.15 which isdefined by the following:

1. Excursions in worker exposure levels mayexceed 3 times the TLV–TWA for no more thana total of 30 minutes during a workday.

2. Under no circumstances should excursions inworker exposure levels exceed 5 times theTLV–TWA, provided that the TLV–TWA is notexceeded.


Medical

Human Studies

No epidemiologic studies investigating theassociation of exposure to CI and respiratorydisease in humans were identified in the publishedmedical literature. One case report postulates thatinhalation of CI may result in pulmonary alveolarproteinosis. McDonald report the development ofthis disorder after exposure to household dust froma ventilation system. The dust contained cellulosefire–resistant fibrous insulation material. Theaffected individual showed symptomaticimprovement once exposure to the insulationmaterial ceased.18

Although direct effects of CI on human healthhave not been studied, cellulose particles fromother sources have been associated with theformation of foreign body granulomas in humans.Zeltner reported a fatal case of pulmonarygranulomatosis in a male drug abuser from illicitintravenous injections of microscopic cellulose, abinding agent in pentazocine tablets.19 Brittandescribed a case of cellulose granulomatousperitonitis in a woman which they ascribed tocellulose contamination during a previous surgery.Within the giant cells and necrotic debris, therewere numerous hollow fibers of varying lengthwith the characteristic morphological features ofvegetable cellulose fibers.20

Although there are no occupational health studiesof CI workers, a Swedish team reported adversehealth outcomes in a soft paper mill. The oddsratios for mortality from chronic obstructivepulmonary disease and from asthma amongexposed workers were significantly elevated.21 Amorbidity study found dose–related irritation of theupper respiratory tract. A decrease in vitalcapacity of the lung was associated with long termexposure to dust.22 Heederik found evidencelower FEV1 in workers exposed to paper mill dustcompared to unexposed workers.23

Animal Studies

In an evaluation of the potential effects of CIinhalation, SPF Wistar rats were exposed to CIdusts. The pulmonary pathology showed evidenceof dose–related changes in pulmonary response,characterized by diffuse macrophage infiltration,microgranuloma formation, alveolitis, and epithelialhyperplasia.24 When Sprague–Dawley rats wereexposed to plant dusts, cellulose–inducedmorphologic changes in the lung were producedthat were identical to granulomatous inflammationand fibrosis, whereas fiber–free extract of wooddust did not cause pathological changes in thelung.25

Milton instilled respirable cotton dust particlesintratracheally in hamsters and produced bothgranulomata and mild centrilobular emphysema.Cellulose–exposed animals had decreased lungdistensibility, noncaseating granulomata, andincreased volume density of parenchymal tissueelements. These changes were cited as hallmarksof the histologically apparent lung fibrosis. Thefibrotic response to cellulose occurred at a highlung burden (total dose was approximately3 milligrams per gram [mg/g] lung tissue). Theauthors noted that toxicity may have been due tooverload of the lung’s capacity to remove insolubleforeign material as well as any intrinsic toxicity ofcellulose.26 However, cotton dust may provokedifferent pulmonary effects than celluloseencountered in paper dust.

Boric Acid

Boric acid, BH3O3, is also known as boracic acid,orthoboric acid, or borofax. It is colorless,odorless, and takes the form of transparentcrystals, white granules, or powder. Boric acidhas a number of uses that include,“weatherproofing wood and fireproofing fabrics;as a preservative; manufacture of cements,


crockery, porcelain, enamels, glass, borates,leather, carpets, hats, soaps, artificial gems, innickeling baths; cosmetics; printing and dyeing;painting; photography; for impregnating wicks;electric condensers; and hardening steel. It is alsoused as an insecticide for cockroaches and blackcarpet beetles.”27

Boric acid is a poison when ingested and ismoderately toxic by skin contact and subcutaneousroutes. Ingestion may cause diarrhea, abdominalcramps, erythematous lesions on skin and mucousmembranes, circulatory collapse, tachycardia,cyanosis, delirium, convulsions, and coma.Ingestion of <5 grams has caused death in infants,and 5–20 grams, in adults. Chronic exposure mayresult in borism (dry skin, eruptions, andgastrointestinal disturbances).28 Workers exposedto boric acid dust at concentrations of >10 mg/m3

experienced eye and upper respiratory tractirritation.29 Heavily impregnated respirablecellulose dust may liberate the readily soluble boricacid in significant amounts in lung tissue.

At this time, there are no relevant evaluationcriteria for boric acid.

Borax

Borax, B4O7Na2.10H2O, is also referred to as

sodium borate decahydrate, disodium tetraboratedecahydrate, sodium tetraborate decahydrate, orsodium pyroborate decahydrate. This compoundis a white, odorless, crystalline solid. Sodiumtetraborates (includes anhydrous, pentahydrate,and decahydrate) are used in the manufacture ofglazes and enamels, are found in cleaningcompounds and fertilizers, and are used in theartificial aging of wood.30

Exposure to borates can result in the irritation ofthe eyes, nose, and throat. High concentrationscan lead to gastrointestinal irritation, kidney injuryand death. 31 An investigation was conducted intothe relationship of estimated borax dust exposures

to respiratory symptoms, pulmonary function, andchest radiograph abnormalities in activelyemployed borax workers.32 Acute respiratoryirritation symptoms (i.e., dryness of the mouth,nose, and throat; dry cough; nose bleeds; sorethroat; productive cough; shortness of breath; andchest tightness) were related to exposures of4 mg/m3 or more. The study indicated thatradiographic abnormalities were uncommon andunrelated to dust exposure, and that borax dustacted as a simple respiratory irritant. NIOSHconducted a health hazard evaluation (HHE)where borax dust samples were collected.33

Eight–hour TWA concentrations ranged from2.9 mg/m3 to 29.9 mg/m3. Employees in the boraxarea reported symptoms of mucous membrane,eye, nose, and throat irritation; some bleeding afternose–blowing; and dry and chapped hands.Workers industrially exposed to borax often sufferfrom chronic eczema; long–term exposure toborax dust may lead to inflammation of themucous membranes of the upper airways and toconjunctivitis.34

The NIOSH REL and the ACGIH TLV for boraxis 5 mg/m3. OSHA does not have a PEL forborax. However, OSHA concluded that an8–hour TWA of 10 mg/m3 (under the vacated1989 PELs) was appropriate for the tetraboratesand that this limit would substantially reduce therisks of eye, skin, and respiratory irritation causedby all forms of sodium tetraborate.35

RESULTS

Comprehensive ProjectResults

Personal ProtectiveEquipment (PPE)

Most of the evaluated contractors provideddisposable, particulate respirators to their


employees. Some of these respirators includedNorth® full–face w/ HEPA filters, 3M® particulatefacepieces , and Gerson® particulate facepieces.Approximately half of the contractors werefamiliar with the new OSHA RespiratoryProtection Standard,36 the NIOSH respiratorcertification system,37 and had implemented theseinto their company’s day–to–day operations. Fewcontractors had a written respiratory protectionprogram established in their workplace. Onecontractor’s employees wore Tyvek™ suits duringattic preparation and CI application.

Cellulose Insulation StatisticalAnalyses

The airborne CI concentration data werelog–transformed to perform statistical analyses onnormally distributed data. Table 1 displays thet–tests comparing wet and dry concentrations ofCI. The table also presents the geometric means,standard deviation, maximum and minimumconcentrations, and p–values. CI installers’exposures to total dust are significantly higherduring dry attic applications compared to wet atticapplications (p < 0.01). Area air samples for totaland respirable dust also revealed a significantlyhigher CI concentration during dry atticapplications than wet attic applications (p < 0.01). The hopper operators’ exposure to total dust wassignificantly higher during wet wall/ceilingapplications than dry wall/ceiling applications(p = 0.02).

Table 2 displays the ANOVA analyses comparingemployees’ or area exposure concentrations usingwet or dry CI, including the geometric means,standard deviation, maximum and minimumconcentrations, and p–values. PBZ air samplesfor total dust varied significantly during dryapplications (p < 0.01). The area air samples forrespirable dust indicated a significant difference inconcentration during dry applications (p = 0.03).

Medical Evaluation

Twenty–three workers participated in the medicalphase of the investigation. All workers who werepresent at the site visits and who were involved inCI application agreed to participate. Medicalevaluations took place at 7 sites. The average ageat the time of the investigations was 36 years(range: 21–62). Their average time that theseworkers were employed in the CI industry was4 years. Almost all installed CI full–time and yearround.

Medical History Questionnaire

On the questionnaire, workers reported severalsymptoms while working with CI. Six workers(26%) reported that they experienced somerespiratory symptoms since they began workingwith CI. The only chronic respiratory symptomreported on the questionnaire was the productionof phlegm in the morning; one worker reportedhaving it always, 2 often, 2 sometimes, and1 rarely. Of the workers who reported morningphlegm, four were current smokers, one was anex–smoker, and one was a never–smoker. Thesmokers were more likely to report phlegmproduction than nonsmokers, but the differencewas not statistically significant.

Eight (35%) workers reported nasal symptoms.These included stuffy nose or drainage.However, none of these workers reported atemporal relationship between their nasalsymptoms and working. Eight (35%) workers alsoreported eye symptoms on the questionnaire,including red, itchy, or watery eyes more thantwice in the previous 12 months. Four (50%) ofthese workers reported a temporal associationbetween their eye symptoms and working. Three(13%) workers reported skin symptoms, whichincluded skin rash, dermatitis, hives, or eczema.Two of the three workers reported a workplaceassociation with their skin symptoms.


Acute Symptoms Survey

Ten (43%) of the 23 workers reported at leastone symptom during the survey. The mostcommon symptom reported on the symptomsurvey was coughing with, 5 of 23 workersreporting being bothered by coughing at least onone occasion. Two workers reported wheezing.One of these workers reported wheezing on 25%of the symptoms survey responses; however, thisworker noted that he had a respiratory tractinfection at the time of the survey. The next mostcommon symptoms were nose symptoms andthroat symptoms, with four workers reporting atleast one nose symptom and four reporting at leastone throat symptom. Only two workers reportedeye symptoms and each reported it only onceduring the site visit. Seven workers reportedjob–related ache or pain within the 12 months priorto completing the questionnaire. The mostcommon complaint was lower back pain

(five workers), followed by shoulder pain (twoworkers).

Peak Flow Monitoring

PEFR was measured on 22 workers five times perday. The median number of days that the workerswere monitored was 3 (range: 1–4). Allmonitoring was at work except the bedtimereading. No monitoring occurred on days whilethe workers were away from work. The percentamplitude mean was less than 20% for allworkers. The median percent amplitude meanwas 7.8%. The highest was 16.9%. None ofthese three workers with percent amplitude meansgreater than 15% reported acute respiratorysymptoms on the symptom survey.

Individual Contractor Results

The following provides a background of eachsampling site and summary results for airsampling, PDM, and VEM conducted during eachcontractor site visit. Appendices A–E present theindividual contractor data (in tabular form) for thePBZ and area air samples, the SEM air samples,the bulk sample analyses, PDM, and VEM results,respectively. For the SEM analyses, the fiberlengths and averages are estimates and areprobably understated due to the difficulty inaccurately measuring the fibers. Each contractorreceived an individual report of their evaluationafter the site visit was completed.

Contractor 1

Background

During January 13 and 14, 1998, NIOSHevaluated three CI application projects inColorado. The first site was an existing attic CIapplication. The attic was approximately450 square feet (ft2), had a roof approximately4–5 feet (ft) high, and was not equipped with an


outside attic ventilation damper (located in atticwall). The application consumed 27 bags(installed dry) to an approximate depth of 8–10".The hopper control was set at full air (10 on a1–10 scale) with no control plates in place. Thesecond site was an existing residential wall CIapplication. Interior walls were injected with CIuntil full through holes made between wall studs atthe top and bottom. The hopper control was set at8; a control plate was in place. The third site wasan existing residential attic CI application. Theattic was approximately 800 ft2, had a 5–6 ft highroof, and was equipped with an outside ventilationdamper. Forty bags of CI were applied dry to adepth of approximately 6–10". The hopper controlwas set at full air; no control plates were in place.

Sampling

Total and Respirable Dust Air Sampling

Over the January 13 and 14, 1998, samplingperiod, the area and PBZ, total dust concentrationsranged from 0.73 mg/m3 to 109.3 mg/m3, while thearea respirable dust concentrations ranged from0.57 mg/m3 to 2.65 mg/m3. The highest total andrespirable dust concentrations were found whileapplying CI into the attic area on January 13. AllPBZ and area, total and respirable dust, 8–hourTWA results were below the OSHA PELs.

There were excursions in worker exposure levelsthat exceeded 5 times the TLV–TWA during theJanuary 13 and 14, 1998, sampling period. ThePBZ total dust concentrations were approximately100 mg/m3 for the attic and hopper workers onJanuary 13 and were approximately 70 mg/m3 forthe attic CI installer on January 14.

Scanning Electron Microscopy Air Samples

Samples collected for SEM analysis were used forexperimental purposes to help define significantparameters to guide future sampling efforts.These factors included: collection time and pump

volume for optimal filter loading, configuration ofSEM instrument parameters for best observationof material collected, initial observation of materialleading to specific characterization procedures,and the general practice of analyzing the samples.Most of the samples taken were overloaded withmaterial.

Portable Dust Monitor Measurements

PDM measurements were collected duringCI–related activities in an existing residential atticon January 13. Measurements were collected inthe attic during preparation activities before the CIapplication began. The MMAD was estimated at7.9 µm with a GSD of 1.9. The respirable massfraction of the sample mass was approximately20%. During the CI application in the attic, theMMAD was estimated at 15 µm with a GSD of2.5 during the CI application in the attic. Therespirable mass fraction of the sample mass wasapproximately 10%. The PDM inside the truckindicated an estimated MMAD of 18 µm and aGSD of 2.2. The respirable mass fraction of thesample mass was approximately 5%. PDMmeasurements were collected during an existingresidential attic CI application on January 14.During the CI application in the attic, the MMADwas estimated at 28 µm with a GSD of 2.4. Therespirable mass fraction of the sample mass wasapproximately 2%. Inside the truck during the CIapplication in the attic, the MMAD was estimatedat 58 µm with a GSD of 2.8. The respirable massfraction of the sample mass was approximately1%.

Video Exposure Monitoring

VEM was performed on CI activities during anexisting residential attic CI application. VEM wasconducted inside the attic and truck to measurerelative air contaminant concentrations andimprove our understanding of how the worker’sindividual tasks affect personal exposure to aircontaminants.38 Samples for total particulate were


collected at the exit of the HAM probe (near theworker’s breathing zone) during celluloseoperations for calibration purposes. The sampleswere used to convert HAM output (volts) toconcentration of total dust. In doing theconversion, one assumes that the aerosol contentis constant. During the following discussion ofresults, the HAM output will be given in terms of“estimated particulate exposure.”

The air sample collected at the exhaust of theHAM sampling probe, during VEM activities inthe attic, indicated a total dust concentration of28.5 mg/m3. The peak estimated particulateexposure measured with the HAM during attic CIactivities was approximately 128 mg/m3.Appendix E – Figure 1 presents the HAMconcentration responses during CI activities in theattic.

VEM was also performed in the truck while theworker dumped bags of CI into the hopper. Theair sample collected at the exhaust of the HAMsampling probe, during VEM activities in the truck,indicated a total dust concentration of 7.1 mg/m3.The peak estimated particulate exposuremeasured with the HAM during CI activities in thetruck was approximately 55 mg/m3. Appendix E– Figure 2 presents the HAM concentrationresponses during CI activities in the truck.

Contractor 2

Background

During April 27–30, 1998, NIOSH investigators(including two industrial hygienists and onemedical officer) evaluated four CI applicationprojects in Missouri. The first site involved a newresidential home attic CI application. The atticroof was approximately 5 ft high and was notequipped with an outside ventilation damper. Thisapplication consumed 58 bags (installed dry) to anapproximate depth of 10". The hopper controlwas set at full air; no control plate was in place.

The second site involved an existing residentialgarage ceiling CI application. Ceiling sectionswere injected with CI until full through holes madein various ceiling locations. The hopper controlwas set at 3½. The third site involved an existingresidential attic CI application. This was a partialattic/wall application project in the attic above thegarage. The attic roof was approximately 7–8 fthigh and was not equipped with an outsideventilation damper. The fourth site involved acontinuation of the project started on April 29.However, application of CI occurred in the mainhouse attic . The attic was approximately 936 ft2,with a 6–7 ft high roof, and was not equipped withan outside ventilation damper. Fifty–three bags ofdry CI were applied to an approximate depth of8–10". The hopper control was set at full air; nocontrol plate was in place.

Sampling


Over the April 27–30, 1998, sampling period, thearea and PBZ total dust concentrations rangedfrom non–detectable to 431 mg/m3, while the arearespirable dust air sample concentrations rangedfrom non–detectable to 3.52 mg/m3. The highestPBZ total dust concentration (431 mg/m3) wascollected on the CI installer during the atticapplication on April 27. The highest respirabledust concentration (3.52 mg/m3) was collected inthe attic area during the CI application on April 30.

During the four days of sampling, three total dust,PBZ, 8–hour TWAs exceeded the OSHA PELand five total dust, PBZ, 8–hour TWAs exceededthe ACGIH TLV. The CI installer on April 27exceeded the OSHA PEL. The applicationoccurred in a new residential attic, which wasrelatively compact, and the CI was applied dry.The CI installer on April 29 also exceeded theOSHA PEL during an attic CI application locatedabove the garage with a wall application around abedroom closet from the second floor. The attic


was spacious except in the corner areas enclosedby the bedroom wall, closet wall, and the roof.The CI installer on April 30 exceeded the OSHAPEL. The two PBZ, 8–hour TWAs over theACGIH TLV, but not the OSHA PEL, were fromthe CI installer of the garage ceiling on April 28and the hopper operator on April 29. The CIinstaller, PBZ, 8–hour TWA included air samplescollected during the ceiling preparation (holedrilling in drywall) and the CI application in thegarage ceiling.

The sampling on April 30 indicated an excursion inworker exposure levels that exceeded 3 times theTLV–TWA for a total of 30 minutes or more,while the 8–hour TWA was below theTLV–TWA. The PBZ, total dust concentrationfor the hopper operator was approximately33 mg/m3.

Scanning Electron Microscopy Air Sampling

The samples collected for SEM analysis indicatedthat a majority of the material observed was CIparticles. The percentage of fibrous material wasapproximately 36%. The CI fibers ranged from5 µm to greater than 150 µm in length. Theaverage CI fiber length was 36 µm.


Near the hopper on April 28, the MMAD wasestimated at 11 µm with a GSD of 1.9. Therespirable mass fraction of the sample mass wasapproximately 11%. Near the hopper on April 29,the MMAD was estimated at 13 µm with a GSDof 2.1. The respirable mass fraction of the samplemass was approximately 9%. During the CIapplication in the attic on April 30, the MMADwas estimated at 20 µm with a GSD of 2.5. Therespirable mass fraction of the sample mass wasapproximately 7%.

Contractor 3

Background

During July 7–10, 1998, NIOSH investigators(including two industrial hygienists and onemedical officer) evaluated four CI application sitesin Ohio. The first site involved a multi–residentialhome wall CI application. The house was threestories high and was inhabited by differentfamilies. The application was the last in a seriesof applications for this particular house. Bedroomand living room interior walls of the second floorwere applied with CI. This site consumed 10 bagsof dry CI. The second site involved a newresidential application. Dry CI was applied to firstand second floor attics. The approximate totalsurface area of the two attics was 570 ft2, withthe second floor attic being slightly larger than thefirst. Each attic was roughly 6 ft high. This siteconsumed 22 bags of CI for the second floor atticand 19 bags for the first floor attic at anapproximate depth of 6–10". The third siteinvolved an existing residential attic application ina six–unit housing complex. The housing complexwas sectioned into an attic above four housingunits and an attic above two. Both attic sectionswere approximately 7 ft high and were equippedwith outside ventilation dampers. These damperswere used to gain entrance into the attics. The jobconsumed 51 bags of dry CI with the four–unithousing side using 28 bags at a depth ofapproximately 8–10". The fourth site involvedanother six–unit housing attic. This attic was notseparated into two distinct sections. The attic wasapproximately 7 ft high, and was equipped with anoutside ventilation damper. Fifty–five bags of CIwere applied dry at a depth of approximately8–10".

Sampling


Over the July 7–10, 1998, sampling period, thearea and PBZ, task specific, total dust air sampleconcentrations ranged from 0.53 mg/m3 to


141 mg/m3, while the area respirable dust airsample concen t r a t ions r anged f romnon–detectable to 2.59 mg/m3. The highest PBZ,total dust air sample (141 mg/m3) was collected onthe CI installer during the attic application onJuly 8. The highest respirable dust air sample(2.59 mg/m3) was collected in the attic area duringthe CI application on July 8.

During the four days of sampling, three total dust,PBZ, 8–hour TWAs exceeded the ACGIH TLV,but not the OSHA PEL. The CI installer in theattic on July 7 exceeded the ACGIH TLV. Thiswas an existing residential wall application.Polyethylene sheeting was used to confinegenerated CI dust to a small area of the room.The CI installer on July 8 exceeded the ACGIHTLV. Two new residential attics were appliedwith CI, both of which were relatively small. TheCI installer in the attic on July 9 exceeded theACGIH TLV. This application consisted of atticpreparation and applying CI.

Sampling conducted on July 9 and 10 indicatedexcursions in worker exposure levels thatexceeded 3 times the TLV–TWA for a total of30 minutes or more, while the 8–hour TWA wasbelow the TLV–TWA. The total dustconcentrations for the hopper operator wereapproximately 35 mg/m3 and 47 mg/m3 on July 9and 10, respectively.


The samples collected for SEM analysis indicatedthat a majority of the material observed was CIparticles. The percentage of fibrous material wasapproximately 36%. The observed CI fibersranged from 5 µm to 90 µm in length. Theaverage CI fiber length was 33 µm.

Contractor 4

Background

During August 10–13, 1998, NIOSH investigators(including three industrial hygienists) evaluatedfive CI application projects in Wisconsin. The firstday involved a new commercial building wall CIapplication. The application of CI at this site tooktwo days to complete. Exterior and some interiorwalls were applied with CI. The first day’sapplication consumed 70 bags of CI. The hopperran at approximately 1700 rpm with an air volumepressure of 9–10 psi. Seventeen bags of CI wereconsumed to complete this job during the secondday. The hopper ran at approximately 2000 rpmand 3 psi. The third day’s applications involvedtwo new residential attics. The first residentialattic was approximately b cathedral style thatrequired crawling between ceiling joists, and aconsisted of a 4–5 ft high roof. The attic was notequipped with an outside ventilation damper. Fiftybags of moistened CI were applied to anapproximate depth of 11½" with an R value of 44.The CI was moistened by a misting device in–linewith the CI application hose. The secondresidential attic was applied with 85 bags to anapproximate depth of 13" with an R factor of 50.This attic was not equipped with an outsideventilation damper. The fourth day involved anew residential attic application. The atticconsisted of a 6–7 ft high roof and was notequipped with an outside ventilation damper. Onehundred twenty–six bags of moistened CI wereapplied to an approximate depth of 11½" with anR value of 44. CI was applied over the garageportion of the attic at an approximate depth of 5".

Sampling


Over the August 10–13, 1998 sampling period, thearea and PBZ, total dust air sample concentrationsranged from 0.31 mg/m3 to 33.3 mg/m3, while thearea respirable dust air sample concentrationsranged from non–detectable to 1.18 mg/m3. Thehighest PBZ air sample for total dust (33.3 mg/m3)was collected on the hopper/roller operator during


the wall CI application on August 10. The highestrespirable dust air sample (1.18 mg/m3) wascollected in the attic area during the CI applicationon August 12.

During the four days of sampling, three total dust,PBZ, 8–hour TWAs exceeded the OSHA PEL.All three 8–hour TWAs exceeding the OSHAPEL occurred during the commercial wall CIapplication on August 10. The CI installer,hopper/roller, and the worker with miscellaneousjobs were overexposed.

Sampling conducted on August 13 indicatedexcursions in worker exposure levels thatexceeded 3 times the TLV–TWA for a total of30 minutes or more, while the 8–hour TWA wasbelow the TLV–TWA. The PBZ, total dustconcentration for the hopper loader was atapproximately 33 mg/m3.




Near the hopper on August 11, the MMAD wasestimated at 16 µm with a GSD of 2.9. Therespirable mass fraction of the sample mass wasapproximately 11%. During the CI application inthe attic on August 12, the MMAD was estimatedat 8.2 µm with a GSD of 3.2. The respirable massfraction of the sample mass was approximately28%. During the CI application in the attic onAugust 13, the MMAD was estimated at 8.5 µmwith a GSD of 4.2. The respirable mass fractionof the sample mass was approximately 32%.

Contractor 5

Background

During September 29 – October 2, 1998, NIOSHinvestigators (including two industrial hygienistsand one medical officer) evaluated seven CIapplication projects in Michigan. The first dayinvolved two new residential home attic and twocondominium attic CI applications. The first atticapplication consumed 70 bags of moistened CI toan approximate depth of 5" resulting in a R–valueof 19. The attic was not equipped with an outsideventilation damper. The second day involved acondominium attic and a new residential atticapplication. The condominium attic applicationconsumed 91 bags of moistened CI. The newresidential attic application applied CI to anapproximate depth of 10" resulting in a R–value of38. The third day involved one existing residentialattic application. The attic roof was approximately3–4 ft high and was not equipped with an outsideventilation damper. The application applied CI toan approximate depth of 7½" resulting in aR–value of 21. The fourth day involved a newresidential wall application. The residence wastwo stories with a basement. The applicationincluded exterior and interior walls.

Sampling


Over the September 29–October 2, 1998, samplingperiod, the area and PBZ, total dust air sampleconcentrations ranged from 2.08 mg/m3 to60.9 mg/m3, while the area respirable dust airsample concen t ra t ions r anged f romnon–detectable to 0.99 mg/m3. The highest PBZair sample for total dust (47.4 mg/m3) wascollected on the CI installer during the atticapplication on October 1. The highest respirabledust air sample (0.99 mg/m3) was collected in thehopper area during the CI application onOctober 1.


During the four days of sampling, one total dust,PBZ, 8–hour TWA exceeded the OSHA PEL,and two total dust, PBZ, 8–hour TWAs exceededthe ACGIH TLV. The CI installer on October 2exceeded the OSHA PEL. The overexposureoccurred during a new residential wall application.The PBZ, 8–hour TWA exceeding the ACGIHTLV, but not the OSHA PEL was the CI installerof the new residential attics on September 29.

Sampling conducted on September 30 indicatedtwo excursions in worker exposure levels thatexceeded 3 times the TLV–TWA for a total of30 minutes or more, while the 8–hour TWA wasbelow the TLV–TWA. The PBZ, total dustconcentration for the CI installer and hopperoperator were approximately 34 and 35 mg/m3,respectively.


The samples collected for SEM analysis indicatedthat a majority of the material observed was CIparticles. The percentage of fibrous material wasapproximately 38%. The observed CI fibersranged from 5 µm to >90 µm in length. Theaverage CI fiber length was 34 µm.


During an attic application on September 29, theMMAD was estimated at 15 µm with a GSD of2.4. The respirable mass fraction of the samplemass was approximately 8%.

Contractor 6

Background

During December 15–18, 1998, NIOSHinvestigators (including three industrial hygienists)evaluated thirteen CI application projects in NorthCarolina. The first day involved applying CI in aspace above a residential garage and sixresidential attics. The initial site was anapplication of the space between the first floor andthe ceiling of the garage. Each attic was roughly1000–1500 ft2 and was applied with roughly 8–10"of moistened CI. The six attics were equippedwith two outside ventilation dampers. The secondday involved a new residential wall application.The residence was two stories with CI applicationin exterior and interior walls. The third day’sapplications involved three new and one existingresidential attic application. The third attic appliedwith CI was equipped with two outside ventilationdampers. The fourth day involved a newresidential attic CI application. The residence wastwo stories with CI application in exterior andinterior walls. During the application the hopperwas set with the following parameters: 2000 rpm,air pressure at 4.0–4.5 psi, and the water pressureat 200 psi.

Sampling


Over the December 15–18, 1998, sampling period,the area and PBZ, total dust air sampleconcentrations ranged from 0.72 mg/m3 to61.3 mg/m3. The area respirable dust air sampleconcentrations ranged from non–detectable to2.43 mg/m3. The highest PBZ air sample for totaldust (41.7 mg/m3) was collected on the hopperoperator during the attic application onDecember 15. The highest respirable dust airsample (2.43 mg/m3) was collected in the hopperarea during the CI application on December 18.

During the four days of sampling, no total dust,PBZ, 8–hour TWAs exceeded the OSHA PEL.There were three total dust, PBZ sample resultsthat exceeded the ACGIH TLV. The CI


installer’s 8–hour TWA exceeded the ACGIHTLV on December 16 and 18, and the hopperoperator’s 8–hour TWA exceeded the ACGIHTLV on December 18.

Sampling conducted on December 15 and 17indicated excursions in worker exposure levelsthat exceeded 3 times the TLV–TWA for a totalof 30 minutes or more, while the 8–hour TWAwas below the TLV–TWA. The PBZ, total dustconcentration for the hopper operators were 41.7and 37.0 mg/m3, respectively.



Contractor 7

Background

During February 23–26, 1999, NIOSHinvestigators (including three industrial hygienists)evaluated three CI application projects inColorado. The first day of the evaluation did notresult in any residences or buildings appropriatefor air sampling. The second day involved anexisting residential attic and a wall CI applicationat the same residence. The attic applicationconsumed 44 bags of moistened CI to anapproximate depth of 5" resulting in an R–value of19. The attic roof was approximately 4 ft high.There was existing fiberglass insulation in theattic. The combination of fiberglass and celluloseinsulation resulted in an R–value of 30. Themisting device orifice was changed midwaythrough the attic application. The original orificewas changed to decrease the amount of watersupplied into the system due to CI clogging theapplication hose. The wall CI application was

performed on the same house and was conductedby two separate CI application crews each withtheir own hopper. The third day of the evaluationdid not result in any residences or buildingsappropriate for air sampling. The fourth dayinvolved an existing residential attic CI application.The attic was roughly 900 ft2. The applicationapplied an R–19 of CI to an existing layer ofinsulation for an overall R–value of 30. The atticroof was approximately 7 ft high.

Sampling


Over the February 23–26, 1999, sampling period,the area and PBZ, total dust air samplec oncentrations ranged from 3.82 to 202 mg/m3.The area respirable dust air sample concentrationsranged from 1.71 mg/m3 to 12.9 mg/m3. Thehighest PBZ air sample for total dust (171 mg/m3)was collected on the CI installer during the atticapplication on February 26. The highest respirabledust air sample (12.9 mg/m3) was collected in thehopper area during the CI application onFebruary 26.

During the four days of sampling, one total dust,PBZ, 8–hour TWA exceeded the OSHA PEL andthree total dust, PBZ, 8–hour TWAs exceeded theACGIH TLV. The hopper operator onFebruary 24 exceeded the OSHA PEL. Thehopper operator was involved with bothapplications on February 24. The PBZ, 8–hourTWAs over the ACGIH TLV, but not the OSHAPEL were the CI installer of the new residentialattic on February 26 and the hopper operator onFebruary 26.

Sampling conducted on February 24 indicatedexcursions in worker exposure levels thatexceeded 3 times the TLV–TWA for a total of30 minutes or more, while the 8–hour TWA wasbelow the TLV–TWA. The PBZ, total dustconcentration for the two samples on the CI


installer were approximately 40 mg/m3 and53 mg/m3. Hopper operator #2 had a PBZ, totaldust concentration of approximately 45 mg/m3.




During an attic application on February 24, theMMAD was estimated at 29.0 µm with a GSD of2.5. The respirable mass fraction of the samplemass was approximately 2.5%. During a wallapplication on February 24, the MMAD wasestimated at 20 µm with a GSD of 2.3. Therespirable mass fraction of the sample mass wasapproximately 2.5%. During an attic applicationon February 26, a NIOSH investigator carried thePDM while following the CI installer around theattic for the first half of the CI application. TheMMAD was estimated at 64 µm with a GSD of2.5. The respirable mass fraction of the samplemass was approximately 0%. During the secondhalf of the attic application on February 26, thePDM was located in the general hopper area.The MMAD was estimated at 55 µm with a GSDof 2.8. The respirable mass fraction of the samplemass was approximately 1%.


VEM was performed in the attic during CIactivities. The air sample collected at the exhaustof the HAM sampling probe indicated a total dust

concentration of 34.6 mg/m3. The peak estimatedparticulate exposure measured with the HAMduring attic CI activities was approximately178 mg/m3. Appendix E – Figure 3 presents theHAM concentration responses during CI activitiesin the attic.

VEM was also performed in the truck while theworker dumped bags of CI into a hopper duringthe attic application. The air sample collected atthe exhaust of the HAM sampling probe indicateda total dust concentration of 140 mg/m3. The peakestimated particulate exposure measured with theHAM during CI activities in the truck was over200 mg/m3. The HAM was at or above themaximum of 200 mg/m3 from 14:47:55 to 14:47:58.Appendix E – Figure 4 presents the HAMconcentration responses during CI activities in thehopper area.

Contractor 8

Background

During March 23–26, 1999, NIOSH investigators(including three industrial hygienists) evaluated sixCI application projects in Arizona. The first day’sproject was a conclusion of the previous day’snew residential wall CI application. Theapplication included interior and exterior walls.The second day involved a new residentialinterior/exterior wall CI application. The third dayconsisted of a new residential attic and wall CIapplication. The residential attic CI applicationapplied 8" (R–30) in the garage and 10" (R–38) inthe house. The application used 177 bags of CI.


The residential wall CI application was located inthe new additions to the existing house, andinvolved exterior walls in a portion of the first andsecond floors of the residence and the ceiling ofthe second floor. The fourth day involved twonew residential houses, one with an attic CIapplication and one with a wall CI application.The application in the attic applied an insulationR–value of 38. The second residence involved awall CI application of interior and exterior walls.

Sampling


Over the March 23–26, 1999, sampling period, thearea and PBZ, total dust air sample concentrationsranged from 1.26 mg/m3 to 97.3 mg/m3. The arearespirable dust air sample concentrations rangedfrom non–detectable to 4.51 mg/m3. The highestPBZ air sample for total dust (97.3 mg/m3) wascollected on the CI installer during the atticapplication on March 26. The highest respirabledust air sample (4.51 mg/m3) was collected in theattic area during the CI application on March 26.

During the four days of sampling, nine total dust,PBZ, 8–hour TWAs exceeded the OSHA PELand eleven total dust, PBZ, 8–hour TWAsexceeded the ACGIH TLV. The 8–hour TWA ofworker #2 and #3 exceeded the OSHA PEL fortotal dust on March 23. Both workers wereinvolved with operating the hopper androlling/recycling the excess CI from the wallapplication . Worker #2's 8–hour TWA exceededthe OSHA PEL for total dust on March 24. Theworker was involved with operating the hopperand rolling/recycling the excess CI from the wallapplication. All three workers’ 8–hour TWAsexceeded the OSHA PEL for total dust onMarch 25 and 26. The 8–hour TWAs of worker# 1 and #3 exceeded the ACGIH TLV, but not theOSHA PEL on March 24. Worker #1 was thewall CI installer. Worker #3 was involved with

operating the hopper and rolling/recycling theexcess CI from the wall application.


The samples collected for SEM analysis indicatedthat a majority of the material observed was CIparticles. The percentage of fibrous material wasapproximately 36%. The observed CI fibersranged from 5 µm to greater than 100 µm inlength. The average CI fiber length was 29 µm.

Portable Dust Monitor Sampling

During a new residential attic CI application onMarch 25, the PDM was located in the attic area.The MMAD was estimated at 115 µm with a GSDof 3.4. The respirable mass fraction of the samplemass was approximately 0%. During a newresidential attic CI application on March 26, thePDM was located in the general hopper area.The MMAD was estimated at 13 µm with a GSDof 2.4. The respirable mass fraction of the samplemass was approximately 11%.


Contractor 9

Background

During September 27–30, 1999, NIOSHinvestigators (including three industrial hygienists)evaluated two CI application projects in Missouri.The first three days were at a new residence.The first day’s project was an exterior wall CIapplication in the basement of the house.Thirty–four bags of CI were used. The secondday involved CI applications in two of the threeattics in the house. The attic CI applicationapplied 147 bags of CI at a depth of 11½" (R–40).The third day involved the last of the three newresidential attics. The attic had CI applied to adepth of 11½". This attic application used 83 bagsof CI. The fourth day involved an existing wall CIapplication. The CI was inserted into the wallsfrom the exterior of the house. Twenty–two bagsof CI were used.

Sampling


Over the September 27–30, 1999, sampling period,the area and PBZ, total dust air sampleconcentrations ranged from 1.3 mg/m3 to58.9 mg/m3. The area respirable dust air sampleconcentrations ranged from non–detectable to0.29 mg/m3. The highest total dust air sample(58.9 mg/m3) was collected in the breathing zoneof the CI installer during the attic application onSeptember 27. The highest respirable dust airsample (0.29 mg/m3) was collected in the atticarea during the CI application on September 29.

During the four days of sampling, two total dust,PBZ, 8–hour TWAs exceeded the OSHA PELand two total dust, PBZ, 8–hour TWAs exceededthe ACGIH TLV. The CI installer’s 8–hourTWA exceeded the OSHA PEL on September 27,1999. The hopper operator’s 8–hour TWAexceeded the OSHA PEL on September 28. The

CI installer's 8–hour TWA exceeded the ACGIHTLV, but not the OSHA PEL on September 28.The hopper operator’s 8–hour TWA exceeded theACGIH TLV, but not the OSHA PEL onSeptember 29.



Contractor 10

Background

During April 5–7, 2000, NIOSH investigators(including three industrial hygienists) evaluated 15CI application projects in Colorado. The firstday’s project involved ten new residential attic CIapplications. All houses received 9" of CI in theattic, which is an R value of 34. There was a totalof 271 bags of CI used for the ten houses. Thesecond day involved three new residential wall CIapplications. The applications used 122 bags ofCI. The third day consisted of two new residentialwall CI applications.

Sampling


Over the April 5–7, 2000, sampling period, thearea and PBZ, total dust air sample concentrationsranged from 1.33 mg/m3 to 68.7 mg/m3. The arearespirable dust air sample concentrations rangedfrom a non–detectable to 0.94 mg/m3. Thehighest PBZ air sample for total dust (68.7 mg/m3)was collected on the CI installer during the wallapplications on April 6. The highest respirabledust air sample (0.94 mg/m3) was collected in thehopper area during the CI application on April 6.


During the three days of sampling, four total dust,PBZ sample results exc eeded the OSHA PEL,and six total dust, PBZ sample results exceededthe ACGIH TLV. The 8–hour TWA of workers#1 , #2, and #3 exceeded the OSHA PEL for totaldust on April 6. Worker #2's 8–hour TWAexceeded the OSHA PEL for total dust onApril 7. The worker was involved with operatingthe hopper and rolling/recycling the excess CIfrom the wall application. The CI installer's(Worker #1) 8–hour TWA exceeded the ACGIHTLV, but not the OSHA PEL on April 5. The CIinstaller's 8–hour TWA exceeded the ACGIHTLV, but not the OSHA PEL on April 7.


The samples collected for SEM analysis indicatedthat a majority of the material observed was CIparticles. The percentage of fibrous material wasapproximately 37%. The observed CI fibersranged from 5 µm to >90 µm in length. Theaverage CI fiber length was 24.6 µm.


During attic CI applications on April 5, the PDMwas located in the general hopper area. TheMMAD was estimated at 16.7 µm with a GSD of2.31. The respirable mass fraction of the samplemass was approximately 7%. During wall CIapplications on April 6, the PDM was located inthe general hopper area. The MMAD wasestimated at 13.1 µm with a GSD of 2.39. Therespirable mass fraction of the sample mass wasapproximately 11%. During wall CI applicationson April 7, the PDM was located in the generalhopper area. The MMAD was estimated at17.7 µm with a GSD of 2.46. The respirable massfraction of the sample mass was approximately7%.

DISCUSSION

Application of Dry CelluloseInsulation

The application of dry CI into attic areas resultedin the generation of PBZ, total dust air sampleconcentrations significantly higher than wet CIattic applications (p < 0.01). The CI installer inthe attic environment has considerable potentialfor an 8–hour TWA exceeding the OSHA PELfor total dust. This is especially true when theactual CI application time (per job and/or the day)increases, the attic area is small, and when theattic requires the installer to crawl into and applyCI in enclosed areas such as cathedral ceilings.The settling of CI dust is relatively slow.Therefore, as application time increases, the cloudof CI dust becomes more dense, increasing thepotential for higher exposure.

CI installers have the potential for 8–hour TWAsexceeding the OSHA PEL for total dust duringwall CI applications. When applying CI intoexisting walls, pressure is generated in the wall.When the application nozzle is taken out of thewall, the pressure inside the wall forces CI out ofthe wall hole which creates a considerable cloudof dust. The dust is typically released into thebreathing zone of the installer. Some contractors,when involved with this type of application hangpolyethylene sheeting to reduce the amount of CIdust settling on interior furniture, pictures, etc .This creates an enclosed area where thegenerated dust can become more dense andincrease the exposure potential.

The ANOVA analysis indicated that the arearespirable dust concentrations varied significantlyby work area during dry CI applications(p = 0.03). Higher respirable concentrations werefound during the application of CI in attic spacesthan in other areas for two possible reasons. Firstthe enclosed nature of attic spaces creates anenvironment with minimal air movement.


Additionally, the lack of air exchange with theoutdoors limits dilution of CI dust in the atticspace. Limited air movement will bias airborneconcentrations to the respirable range as largerparticulates settle out. Therefore, the attic spaceshould see a gradual increase in airbornerespirable CI over time. Second the extensiveamount of CI dust generated will naturally containa larger amount of respirable material.

Application of Wet CelluloseInsulation

A moistening system, which is operating correctly,has the potential to reduce the concentration of CIdust during attic CI applications. This results inless potential for CI installers to exceed theOSHA PEL for total dust (example,Contractor 4). The proper operation of the systemdepends upon the correct amount of water beingadded (according to the manufacturersspecifications) and sufficient hopper strength toforce moistened CI from the truck into the attic.When there are problems with this system, theexposure potential increases (example,Contractor 7). Higher concentrations were foundduring this wet attic application (and one samplewith Contractor 8) which were not found during allother site visits with contractors having mistingsystems.

CI installers, hopper operators, and CI recyclersall have the potential for 8–hour TWAs exceedingthe OSHA PEL for total dust during wet wall CIapplications. When applying CI between wallstuds, the force of the CI being released from theapplication hose and hitting the wall generates acloud of CI dust. The nature of this type ofapplication requires that all three employees be inclose proximity to the wall and therefore thegenerated dust. After the CI fills the spacebetween wall studs, a roller is used to roll off theexcess CI, to provide a consistent depth. To rolloff the material between 8–10 ft in height, theroller operator has to stretch his/her arms to reachthe top of the wall. This results in excess CIfalling onto that employee and into his/herbreathing zone. This excess material is thenrecycled by a vacuum connected to the hopper orit can be collected by shovel and deposited backinto the hopper by bags, cans, etc. The closenessof the recycling operation to the CI application canlead to high airborne concentrations. The hopperoperator had total dust exposures significantly


higher during wet wall/ceiling applications than dry(p = 0.02). The hopper operator during wetwall/ceiling applications typically works with thehopper, the roller, and sometimes the recyclingportion of the process. This exposes the workerto greater exposure potential as was describedabove.

Fiber Characterization ofCellulose Insulation

Cellulose fibers were observed and characterizedby SEM analysis, which indicated that fibers wereon average 28 µm in length and ranged from 5 µmto 150 µm. The fibers come in various shapes andsizes, are rarely linear, can be found attached tocellulose particles, and do not typically have auniform diameter. The variable fiber diametercould not easily be measured. The fibers tend tocurve and twist, especially the longer fibers, intoconvoluted shapes that were difficult tocharacterize (see Appendix F – Pictures 7 and 8).This also caused many of the fibers to not lay flaton the filter. This resulted in differential chargingof the fibers, making them less stable. Thisreduction in stability primarily affected the imagequality.

The various shapes, sizes, diameters, andnon–linearity of CI fibers, complicates the issue offiber respirability. Classifying whether a fiber isrespirable or not depends heavily on the diameterof the fiber. The inability to measure the diameterof CI fibers makes it difficult to conclude whetherthey are respirable or not. Further research intoCI fiber characteristics is warranted before arespirability conclusion is made.

Bulk Samples of CI

The CI bulk samples were analyzed by a waterextraction and a strong acid extraction. The waterextrac tion indicated a boron and sulfate range of4700–25000 µg /g o f ma te r i a l and

25000–97000 µg/g of material, respectively. Thestrong acid extraction indicated a boron andsulfate range of 5900–26000 µg/g of material and29577–94000 µg/g of material, respectively.Assuming that all boron and sulfate detectedoriginates from the fire–retarding materials added,the amount is approximately 0.5–2.5% and2.5–10% by weight of CI material, respectively.The boron levels are low in the bulk samples. Thepotential for exposures to high concentrations ofboron in individual air samples is extremelyunlikely. Sulfate levels are higher than boronlevels in the bulk samples. However, sulfatesoccur naturally in wood products and probably addto the overall amount detected. Both extractionmethods found a number of other metals in bothanalyses. The metals consistently detectedincluded: aluminum, calcium, copper, iron, lithium,magnesium, manganese, sodium, titanium, andzinc.

Real–time Monitoring

The real–time monitoring with the PDM assistedin characterizing the particulate size of thegenerated CI dust. The real–time monitoringduring the various CI related activities resulted inMMADs typically greater than 10 µm with GSDsbetween 2.0 and 3.0 (See Appendix D). Thisindicates that the particle size distribution is biasedtowards particle sizes out of the respirable rangeof 10 µm and smaller. The percent respirablematerial was typically lower than 11%. Theamount of respirable material calculated from thePDM data agrees with the respirable dustair sampling results. A large amount of respirablematerial is not generated during CI applications.However, both the PDM and the respirable dustsamples were area and not PBZ samples. Ahigher concentration of dust, as seen in atticsduring dry application, may result in a largeramount of respirable material and an increasedexposure potential to employees not indicated byarea sampling.


Contractors 7 and 8 had real–time monitoringevents where the calculated respirable massfraction was at or slightly above 0%. The PDMhas a maximum concentration that it can measure.At or above this maximum concentration, theinstrument is unable to classify the partic les intothe eight size ranges. The instrument indicatesthat each size range has the same amount ofmass. Therefore, when the respirable massfraction is calculated from the data provided bythe instrument and that data has concentrationreadings above the maximum, the percentage islower.


The VEM assisted in our understanding of therelationship between employee CI relatedactivities and total dust concentrations (SeeAppendix E – Figures 1–4). A qualitativeassessment of the concentrations measured withthe HAM during VEM indicate that the CIinstaller is exposed to the highest particulateconcentrations when working in “tight areas” suchas in the edges of the attic or applying theinsulation near the body. The hopper operator isexposed to the highest particulate concentrationsw hen dumping the bags of CI into the hopper.The initial positioning of the CI block into thehopper creates a large cloud of dust, thus creatinga higher concentration.

Engineering Controls,Administrative Controls, andPersonal ProtectiveEquipment

Engineering controls in the hopper area can assistin the control of CI dust (Figures 1 and 2). Thefigures show baffles around the sides of thehopper and an exhaust fan. The baffles will assistin keeping the CI dust in a controlled area, whichthe fan will exhaust to the outside of the truck.

(Note: Figure 1 – high winds could decrease theeffectiveness of the exhaust fan.) Engineeringcontrols for other CI applications are not apractical solution to controlling dustconcentrations. The VEM during atticapplications indicated that employees had greaterpotential for exposure to CI dust when applying CIin corners and close to the body. Minimizing thesepractices when possible will reduce the potentialexposure. This may be accomplished by utilizinga light weight (i.e., light weight metal) extensionthat would extend approximately 4 ft from the endof the application hose. This extension could havehandles so the worker can manipulate the hoseand extension to point into the tight areas;therefore, reducing the possibility of the workerhaving to physically enter the enclosed area.

The wide range of dust concentrations measuredduring CI applications complicates the respiratorselection process for the CI industry. Theexposure data in this report indicate that workerswere exposed to CI total dust concentrationsabove the OSHA PEL. Therefore, untilengineering controls and work practices aredeveloped that will reduce exposures to safelevels, the OSHA Respiratory ProtectionStandard, 29, Code of Federal Regulations1910.13439 requires that CI employers mus tprovide respirators to their employees andestablish and maintain a respiratory protectionprogram in accordance with the standard’srequirements.

Respirators typically have an assigned protectionfactor (APF) which describes the level ofrespiratory protection in the workplace that shouldbe expected by a certain respirator underconditions where an employee has been fit testedand has had appropriate training. Based on thevariation in CI total dust concentrations, theoverexposures to the OSHA PEL for total dust,and the APF of each respirator, employees in allareas of CI related activities (CI installer, hopperoperator, and CI recycler) should wear at a


minimum, a disposable, half–mask, particulatefiltering respirator. Respirators used should beNIOSH–approved with an N95 designation (asdefined by the current NIOSH certificationprocedures 42 CFR 84 effective July 10, 1998).40

The N95 designation indicates that the filtermaterial has been shown to remove 95% ofparticles greater than or equal to 0.3 µm. (The"N" stands for, Not resistant to oil).Unfortunately, there is no APF for disposablerespirators. A NIOSH document onHistoplasmosis 41 suggests an APF of 5–10 fordisposable respirators. NIOSH is currentlystudying these types of respirators to assign apermanent APF. If these respirators are beingused, the employees should be quantitativelyfit–tested to ensure an acceptable fit.

The exposure data indicates that there areinstances, such as applying dry CI into attics,where the use of a more protective respiratorwould be recommended. Elastomeric, half–face,air–purifying respirators with N95 filters areassigned an APF of 10 and are acceptable fordust concentrations of 10 times the OSHA PEL(150 mg/m3). Elastomeric, full–face, air–purifyingrespirators have an APF of 50 times the PEL(750 mg/m3) and also have the benefit of eyeprotection. Employers will have to review theexposure data and decide what is the mostappropriate respiratory protection for theirworkers.

Medical

Twenty–three CI workers were studied forpossible health effects associated with CIexposure. These workers reported a variety ofsymptoms which may or may not be associatedwith their workplace exposure to CI. The mostcommon chronic respiratory symptom reportedwas morning phlegm production. However, mostof those who reported that symptom were currentsmokers, which could explain their symptoms.

Smokers were more likely to report phlegmproduction.

The most common symptom, reported on thequestionnaire, to be temporally related to CIexposure was that of eye irritation (cough andnasal symptoms were reported relativelyfrequently, but they were not temporally related toexposure to CI). Thirty–five percent of theworkers reported that they had eye symptoms thatwere worse during exposure to CI. Thesesymptoms may be due to additives in CI, such asboric acid, or to dust. Most workers did not weareye protection. Most workers reported that theireye symptoms improved once exposure ended.

None of the workers had evidence of bronchialhyper–reactivity (percent amplitude means ofgreater than 20%), an indication of occupationalasthma. However, the small number of workersstudied decreased the likelihood of findingbronchial hyper–reactivity because the prevalenceof occupational asthma is relatively low for mostallergens.42 Also, PEFR was measured mostly atwork which limits the ability to detect themaximum change in PEFR that may haveoccurred. Measuring PEFR only on workdaysand not the weekend (or extended time away fromwork) reduces the likelihood of seeing awork–related pattern and delayed effects.However, there are several limitations to ourability to assess bronchial hyper–reactivity, whichmay indicate asthma. A few workers reportedlower respiratory tract symptoms, but thesesymptoms were classified as mild and infrequentand did not worsen with continued exposure.

CONCLUSIONS

# Based on the air sample data collected fromthe ten contractor site visits, NIOSH investigatorsconclude that there is a potential for overexposureto CI. Employees in virtually all CI applicationactivities had the potential to be exposed to CI


total dust levels which would exceed the OSHA8–hour TWA. There is also a possibility forexceeding ACGIH excursion limits even if the8–hour TWA limits themselves are not exceeded.Area respirable dust concentrations were typicallylow. However, there is increased potential for8–hour TWAs exceeding the OSHA PEL for totaland respirable dust when employees are involvedin CI application activities for longer periods oftime during the day.

# Applying wet CI into attics significantlyreduces the amount of generated dust.

# Applying CI in close proximity to attic walls orcorners and in tightly enclosed areas can result inexposure to elevated concentrations of CI dust.

# The hopper operator can be exposed to highc oncentrations of CI dust, especially during atticapplications, when putting bags of CI into thehopper.

# There is evidence of work–related eye andmucous membrane irritation among some workers.This may be due to the additives present in CI,such as boric acid. From this investigation there islittle evidence of lower respiratory system healthconditions associated with CI exposure.However, this investigation has several limitationsin addressing this issue.

RECOMMENDATIONS

The following recommendations are based on thefindings of this investigation and offered toimprove the safety and health of employeesworking with the CI operations discussed in thisreport.

1. Continue the use of personal protectiveequipment, specifically respirators. Engineeringcontrols are the preferred method of control,however, until effective engineering controls canbe implemented, respirators are an effectiveinterim measure.

! A written respiratory protection programshould be developed. This program should includethe following components: selection of respirators;medical evaluation; fit testing; use of respirators;maintenance and care of respirators; identificationof filters; training and information; programevaluation; and recordkeeping.

! Employees should be provided at leastdisposable, half–mask, particulate filteringrespirators. Respirators used should beNIOSH–approved with an N95 designation.

! In enclosed attic spaces (i.e., cathedralceilings) the CI concentrations may be high;therefore, a respirator with a higher APF (i.e.,N95 elastomeric half–face or full–face respirator)should be used.

! Publications developed by NIOSH can bereferenced when developing an effectiverespiratory program; these include the NIOSHRespirator Decision Logic 43 and the NIOSHGuide to Industrial Respiratory Protection.44

2. Use a moistening device when applying CIinto attic spaces.


1. Lea D. [1999]. Telephone conversation onAugust 26, 1999, between D. Lea, CelluloseInsulation Manufacturers Association, and R.McCleery, Division of Surveillance, HazardEvaluations, and Field Studies, National Institutefor Occupational Safety and Health, Public HealthService, U.S. Department of Health and HumanServices.

2. Code of Federal Regulations [1997]. 16 CFR1209. Washington, DC: U.S. GovernmentPrinting Office, Office of the Federal Register.

3. ASTM [1991]. Standard specification forcellulosic fiber (wood base) loose–fill thermalinsulation. Philadelphia, PA: American Society forTesting and Materials, ASTM C739–91.

4. ASTM [1997]. Standard specification forself–supported spray applied cellulosic thermalinsulation. Philadelphia, PA: American Society forTesting and Materials, ASTM C1149–97.

5. NIOSH [1985]. Hazard evaluation andtechnical assistance report: Duluth CommunityAction Program, Duluth, MN. Cincinnati, OH:U.S. Department of Health and Human Services,Public Health Service, Centers for DiseaseControl, National Institute for Occupational Safetyand Health, DHHS (NIOSH) Publication No.

84–213, 391–1619.

6. NIOSH [1990]. Hazard evaluation andtechnic al assistance report. Department ofEnergy, Westside Energy Co–Op, Denver, CO.Cincinnati, OH: U.S. Department of Health andHuman Services, Public Health Service, Centersfor Disease Control, National Institute forOccupational Safety and Health, DHHS (NIOSH)Publication No. 90–151–L2067.

7. Code of Federal Regulations [1996]. 16 CFR460. Washington, DC: U.S. Government PrintingOffice, Federal Register.

8. NIOSH [1994]. NIOSH manual of analyticalmethods. 4th ed. Cincinnati, OH: U.S.Department of Health and Human Services,Public Health Service, Centers for DiseaseControl and Prevention, National Institute forOccupational Safety and Health, DHHS (NIOSH)Publication No. 94–113.

9. Grimm. Dust Monitor Instruction Manual,Series 1.100 v.5.10 E, Grimm Labortechnik GmbH& Co. KG, Ainring, Germany.

10. NIOSH [1992]. Gressel, MG, Hietbrink WA,eds. Analyzing workplace exposures using directreading instruments and video exposure monitoringtechniques. U.S. Department of Health andHuman Services, Centers for Disease Control,National Institute for Occupational Safety andHealth, DHHS (NIOSH) Publication No. 92–104.

11. Gressel MG, Heitbrink WA, McGlothlin JD,Fischbach TJ [1988]. Advantages of real–timedata acquisition for exposure assessment. ApplInd Hyg 3(11):316–320.

12. Gressel MG, Heitbrink WA, McGlothlin JD,Fischbach TJ [1987]. Real–time, integrated, andergonomic analysis of dus t exposure duringmanual materials handling. Appl Ind Hyg2(3):108–113.

3. Refer to Figures 1 and 2 for suggestedengineering controls for the hopper area.Employers should contact a qualified engineeringfirm to assist in developing effective engineeringcontrol measures.4. Appropriate housekeeping and hygiene shouldbe standard practice with CI companies. Aregular cleaning schedule for trucks and companyfacilities will help keep CI dust to a minimum.Good hygiene practices may reduce the possibilityof exposures by routes other than inhalation, suchas ingestion by hand–to–mouth contact.

REFERENCES


13. Higgins BG, Britton JR, Chinn S, et al. [1992]Comparison of bronchial reactivity and peakexpiratory flow variability measurements forepidemiologic studies. Am Rev Resp Dis145:588–593.

14. NIOSH [1992]. Recommendations foroccupational safety and health: compendium ofpolicy documents and statements. Cincinnati, OH:U.S. Department of Health and Human Services,Public Health Service, Centers for DiseaseControl and Prevention, National Institute forOccupational Safety and Health, DHHS (NIOSH)Publication No. 92–100.

15. ACGIH [2000]. 2000 TLVs ® and BEIs®:threshold limit values for chemical substances andphysical agents. Cincinnati, OH: AmericanConference of Governmental IndustrialHygienists.

16. CFR [1997]. 29 CFR 1910.1000. Code ofFederal regulations. Washington, DC: U.S.Government Printing Office, Office of the FederalRegister.

17. ACGIH [1991]. Particulates not otherwiseclassified (PNOC). In: Documentation of thethreshold limit values and biological exposureindices, Sixth ed. Cincinnati, OH: AmericanConference of Governmental Industrial Hygienists,Inc.

18. McDonald JW, Alvarez F, Keller CA. [2000].Pulmonary alveolar proteinosis in association withhousehold exposure to fibrous insulation material.Chest 117(6):1813–7.

19. Zeltner TB, et al. [1982]. Unusual pulmonaryvascular lesions after intravenous injections ofmicrocrystalline cellulose. Virchows Arch [PatholAnat J] 395(2): 207–16.

20. Brittan RF et al. [1994]. Cellulosegranulomatous peritonitis. Br J Surg 71(6): 452–3.

21. Thoran K, Jarvholm B, Morgan U. [1989].Mortality from asthma and chronic obstructivepulmonary disease among workers in a soft papermill: a case–referent study. Br J Ind Med46:192–5.

22. Jarvholm B, Thoran K, Brolin I, et al. [1988].Lung function in workers exposed to soft paperdust. Am J Ind Med 14:457–64.

23. Heederik D, Burdorf L, Boleij J, Willems H,van Bilsen J. [1987]. Pulmonary function andintradermal tests in workers exposed to soft–paperdust. Am J Ind Med 11:637–45.

24. Hadley JG, Kotlin P, Bernstein DM. [1992].Subacute (28 days) repeated dose inhalationtoxicity of cellulose building insulation in the rat.Toxicologist 12:225.

25. Tatrai E, Adamis Z, Bohm U, Meretey K,Ungvary G. [1995]. Role of cellulose in wooddust–induced fibrosing alveo–bronchiolitis in rat.J Appl Tox 15(1):45–8.

26. Milton DK, Godleski JJ, Feldman HA,Greaves IA. [1990]. Toxicity of intratracheallyinstilled cotton dust, cellulose, and endotoxin. AmRev Resp Dis 142(1):184–92.

27. Merck & CO., Inc. [1996]. The Merck index.12th ed. Whitehouse Station, NJ: Merck & CO.,Inc., p. 1365.

28. Lewis, RJ Sr. [1992] Sax’s dangerousproperties of industrial materials. 8th ed. Vol 2.New York, NY: Van Nostrand Reinhold, p. 529.

29. NLM [1995] HSDB (Hazardous SubstancesData Bank), Bethesda, MD, searched December1998 [Record No. 1423, boric acid].

30. ACGIH [1991]. Borates, tetra, sodium salts.In: Documentation of the threshold limit valuesand biological exposure indices, Sixth ed.Cincinnati, OH: American Conference of


Governmental Industrial Hygienists, Inc.

31. Hathaway, GJ, Proctor NH, Hughes JP[1996]. Chemical hazards of the workplace, 4th

ed. New York, NY: Van Nostrand Reinhold.

32. Garabrant DH, Bernstein L, Peters JM, SmithTJ, Wright WE [1985]. Respiratory effects ofborax dust. Br J Ind Med 42(12):831–837.

33. NIOSH [1978]. Health hazard evaluationdetermination report. Kerr–McGee ChemicalCorporation, Trona, California. Cincinnati, OH:U.S. Department of Health, Education, andWelfare, Public Health Service, Center forDisease Control, National Institute forOccupational Safety and Health, DHEW(NIOSH) Publication No. 77–59–496.

34. NLM [1995] HSDB (Hazardous SubstancesData Bank), Bethesda, MD, searched December1998 [Record No. 328, borate]

35. Code of Federal Regulations [1989]. 29 CFR1910.1000. Washington, DC: U.S. GovernmentPrinting Office, Federal Register.


37. NIOSH [1996]. NIOSH guide to theselection and use of particulate respiratorscertified under 42 CFR 84. Cincinnati, OH: U.S.Department of Health and Human Services,Public Health Service, Centers for DiseaseControl and Prevention, National Institute forOccupational Safety and Health, DHHS (NIOSH)Publication No. 96–101.

38. Gressel MG, Heitbrink WA, Jensen PA,Cooper TC, O’Brien DM, McGlothlin JD,Fishbach TJ, Topmiller JL [1992]. AnalyzingWorkplace Exposures Using Direct ReadingInstruments and Video Exposure MonitoringTechniques. Cincinnati, OH: U.S. Department of

Health and Human Services, Centers for DiseaseControl, National Institute for Occupational Safetyand Health, Division of Physical Sciences andEngineering, DHHS (NIOSH) Publication Number92–104.


40. NIOSH [1996]. NIOSH guide to theselection and use of particulate respiratorscertified under 42 CFR 84. Cincinnati, OH: U.S.Department of Health and Human Services,Public Health Service, Centers for DiseaseControl and Prevention, National Institute forOccupational Safety and Health, DHHS (NIOSH)Publication No. 96–101.

41. NIOSH [1997]. Histoplasmosis – protectingworkers at risk. Cincinnati, OH: U.S.Department of Health and Human Services,Public Health Service, Centers for DiseaseControl and Prevention, National Institute forOccupational Safety and Health, DHHS (NIOSH)Publication No. 97–146.

42. Bernstein JA, Bernstein IL. Occupationallyinduced asthma. In Allergy, 2nd ed. Kaplan AP,ed. Philadelphia, W.B. Saunders Company. pp.511–24.

43. NIOSH [1987]. NIOSH respirator decisionlogic. Cincinnati, OH: Department of Health andHuman Services, Public Health Service, Centersfor Disease Control, National Institute forOccupational Safety and Health, DHHS (NIOSH)Publication No. 87–108.

44. NIOSH [1987]. NIOSH guide to industrialrespiratory protection. Cincinnati, OH:Department of Health and Human Services,Public Health Service, Centers for DiseaseControl, National Institute for Occupational Safetyand Health, DHHS (NIOSH) Publication No.87–116.


TABLES

Table 1. T–test results comparing log transformed concentration values for dry and wetCI application methods.

Groups Method N GM GSD Min* Max* p–value

PBZ, total dust, attic CIapplication, CI installer

dry

wet

22

29

74.8

18.7

2.33

2.85

16.2

1.27

431

97.3< 0.01

PBZ, total dust, attic CIapplication, hopper operator

dry

wet

13

24

25.8

17.8

3.09

2.56

2.17

0.82

140

58.30.29

PBZ, total dust, wall/ceiling CIapplication, CI installer

dry

wet

9

27

20.2

26.2

2.66

1.80

3.86

4.34

78.7

80.60.47

PBZ, total dust, wall/ceiling CIapplication, hopper operator

dry

wet

7

30

9.99

22.2

2.98

2.03

1.22

2.08

44.6

61.30.02

Area, total dust, attic CIapplication

dry

wet

11

19

23.8

6.19

2.32

4.09

7.68

0.31

98.1

38.3< 0.01

Area, total dust, hopper w/ atticCI application

dry

wet

10

23

13.4

15.0

3.32

3.82

1.67

0.74

101

2020.82

Area, total dust, hopper w/ wallCI application

dry

wet

5

22

5.46

11.5

9.20

2.82

0.73

1.3

61.1

61.30.50

Area, respirable dust, attic CIapplication

dry

wet

10

19

1.53

0.11

1.62

12.8

0.84

0.01

3.52

8.54< 0.01

Area, respirable dust, hopper w/attic CI application

dry

wet

9

21

0.15

0.45

8.10

5.38

0.01

0.01

1.24

12.90.15

Area, respirable dust, hopper w/wall CI application

dry

wet

5

12

0.36

0.28

14.7

6.18

0.01

0.01

8.70

2.430.83

* = minimum and maximum of untransformed concentration data in mg/m3

N = number of samplesGM = geometric mean


GSD = geometric standard deviation

Table 2. ANOVA result during dry or wet CI application methods.

Groups Method N GM GSD Min* Max* p–value

CI installer, TD, attic

Hopper operator, TD, attic

CI installer, TD, wall/ceiling

Hopper operator, TD, wall/ceiling

dry

22

13

9

7

74.8

25.8

20.2

9.99

2.33

3.09

2.66

2.98

16.2

2.17

3.86

1.22

431

140

78.7

44.6

< 0.01

CI installer, TD, attic

Hopper operator, TD, attic

CI installer, TD, wall/ceiling

Hopper operator, TD, wall/ceiling

wet

29

24

27

30

18.7

17.8

26.2

22.2

2.85

2.56

1.80

2.03

1.27

0.82

4.34

2.08

97.3

58.3

80.6

61.3

0.33

Area, TD, attic CI application

Area, TD, hopper w/ attic CI install

Area, TD, hopper w/ wall CI install

dry

11

10

5

23.8

13.4

5.46

2.32

3.32

9.20

7.68

1.67

0.73

98.1

101

61.1

0.14

Area, TD, attic CI application

Area, TD, hopper w/ attic CI install

Area, TD, hopper w/ wall CI install

wet

19

23

22

6.19

15.0

11.5

4.09

3.82

2.82

0.31

0.74

1.3

38.3

202

61.3

0.08

Area, RD, attic CI application

Area, RD, hopper w/ attic CI install

Area, RD, hopper w/ wall CI install

dry

10

9

5

1.53

0.15

0.36

1.62

8.10

14.7

0.84

0.01

0.01

3.52

1.24

8.70

0.03

Area, RD, attic CI application

Area, RD, hopper w/ attic CI install

Area, RD, hopper w/ wall CI install

wet

19

21

12

0.11

0.45

0.28

12.8

5.38

6.18

0.01

0.01

0.01

8.54

12.9

2.43

0.09

* = minimum and maximum of untransformed concentration data in mg/m3

N = number of samplesGM = geometric meanGSD = geometric standard deviation


TD = total dustRD = respirable dust


Hopper – againstside of truck

Exhaust FanBack ofTruck

Front of Truck

CelluloseInsulation

Side Barriers

Figure 1. Proposed engineering control for hopper area.

H o p p e r – a g a i n s ts i d e o f t r u c k

E x h a u s t F a n

B a c k o fT r u c k

F r o n t o f T r u c k

C e l l u l o s eI n s u l a t i o n

S i d e B a r r i e r s

T r u c k C e i l i n g

O u t s i d e

Figure 2. Proposed engineering control (#2) for hopper area.

FIGURES


APPENDICES

A. Contractor 1–10 Total and Respirable Dust Sampling Results

Contractor 1 – Total and Respirable Dust Sampling Results.

LocationSampleTime

(military)

SampleVolume(liters)

SampleConcentration

(mg/m3)

8–hourTWA

(mg/m3)

Results of January 13, 1998, area and PBZ air sampling during an existing residential attic CI application.

Area (total) – Inside truck – near hopper

Area (total) – Inside attic, on rafter, middle of attic

PBZ (total) – Hopper operator sample

PBZ (total) – CI installer sample

Area (respirable) – Inside truck – near hopper

Area (respirable) – Inside attic, on rafter, middle of attic

1000 – 1047

1009 – 1052

1000 – 1045

1006 – 1046

1000 – 1047

1009 – 1052

90

85.4

88.5

78.8

79.3

71.8

100.9

52.31

100.4

109.3

0.57

2.65

9.88

4.69

9.41

9.11

0.06

0.24

Results of January 13, 1998, area and PBZ air sampling during an existing residential wall CI application.

Area (total) – In truck on hose holder

PBZ (total) – Wall CI installer – upstairs and basement

PBZ (total) – Hopper operator – using HAM instrument

Area (respirable) – In truck on hose holder

1410 – 1438

1354 – 1437

1404 – 1445

1410 – 1438

27.6

84.7

82

47.2

0.725

8.74

1.22

0.636

0.04

0.78

0.10

0.04

Results of January 14, 1998, area and PBZ air sampling during an existing residential attic CI application.


Area (total) – In truck above hopper

Area (total) – 2nd sample – in truck – hopper

Area (total) – west side of house – close to atticentrance


PBZ (total) – 2nd Hopper operator sample

PBZ (total) – 3rd Hopper operator sample – using HAMinstrument


PBZ (total) – 2nd CI installer sample – using HAMinstrument

Area (respirable) – west side of house – close to atticentrance

Area (respirable) – In truck above hopper

1328 – 1352

1352 – 1500

1333 – 1444

1326 – 1357

1357 – 1457

1421 – 1457

1427 – 1442

1339 – 1356

1333 – 1444

1328 – 1500

24.8

70.2

64.9

31.4

60.8

72

14.7

34

108.8

153

29.44

31.77

8.48

8.92

10.69

6.81

68.71

27.94

1.38

1.24

5.97

1.25

2.42

3.14

0.20

0.24

Appendix A. Contractor 2 – Total and Respirable Dust Sampling Results.

LocationSampleTime

(military)


SampleConcentration

(mg/m3)

8–hourTWA

(mg/m3)

Results of April 27, 1998, area and PBZ air sampling during a new residential attic CI application.

Area (total) – Indoor background

Area (total) – Attic sample – near attic entrance

Area (total) – Hopper sample – to rt. of hopper

PBZ (total) – CI installer

PBZ (total) – 2nd attic sample – CI installer

PBZ (total) – 3rd attic sample – CI installer

PBZ (total) – Hopper operator

Area (respirable) – Indoor background

Area (respirable) – Attic sample – near attic entrance

Area (respirable) – Hopper sample – to rt. of hopper

0941 – 1243

1031 – 1150

1028 – 1244

1027 – 1051

1051 – 1135

1135 – 1146

1029 – 1244

0941 – 1243

1031 – 1150

1028 – 1245

190

80.1

140

25.7

47.2

11.8

138

319

138

237

0.58

98.1

5.08

220

199

431

18.1

ND

1.38

0.29

16.2

1.44

39.0

5.08

0.23

0.08

Results of April 28, 1998, area and PBZ air sampling during an existing residential garage ceiling CI application.


Area (total) – Garage sample – middle steel support

Area (total) – 2nd garage sample – middle steel support


PBZ (total) – Garage ceiling – drilling drywall

PBZ (total) – Garage ceiling – CI application


Area (respirable) – Garage sample – middle steel support


1029 – 1107

1334 – 1622

1035 – 11101338 – 1627

0939 – 1009

1028 – 11061334 – 1621

1037 – 11071337 – 1627

1029 – 11071334 – 1622

1035 – 11101338 – 1627

38.4

170

207

30.3

207

202

353

345

ND

4.06

1.70

32.3

21.9

12.9

0.11

0.06

1.42

0.72

11.4

5.41

0.05

0.03


Appendix A. Contractor 2 – Total and Respirable Dust Sampling Results Cont...

LocationSampleTime

(military)


SampleConcentration

(mg/m3)

8–hourTWA

(mg/m3)

Results of April 29, 1998, area and PBZ air sampling during an existing residential attic CI application.

Area (total) – Attic above garage – driveway side – onrafter



PBZ (total) – 2nd CI installer sample



Area (respirable) – Attic above garage – driveway side– on rafter


1143 – 13031349 – 1420

1205 – 13061349 – 1428

1143 – 1237

1237 – 13021349 – 1434

1135 – 1302

1353 – 1428

1143 – 13031349 – 1420

1205 – 13061349 – 1428

117

102

54.1

70.1

88.3

35.5

192

171

23.1

1.67

54.2

105

20.4

94.4

0.84

ND

5.34

0.35

21.4

10.6

0.19

ND

Results of April 30, 1998, area and PBZ air sampling during an existing residential attic CI application.

Area (total) – Attic prep. – near attic entrance

Area (total) – CI application – near attic entrance

Area (total) – Hopper sample – rt. of hopper

PBZ (total) – attic preparation – using fiberglass




Area (respirable) – Attic prep. – near attic entrance

Area (respirable) – CI application – near attic entrance

Area (respirable) – Hopper sample – rt. of hopper

1023 – 1212

1307 – 1354

1308 – 1446

1027 – 1209

1306 – 1331

1331 – 1350

1310 – 1446

1032 – 1212

1307 – 1354

1308 – 1446

107

46.3

99.5

99.1

24.3

18.5

99.1

169

79.6

169

5.12

38.2

5.33

41.5

164

50.3

32.8

0.65

3.52

0.47

4.91

1.09

18.8

6.56

0.48

0.10



LocationSampleTime

(military)


SampleConcentration

(mg/m3)

8–hourTWA

(mg/m3)

Results of July 7, 1998, area and PBZ air sampling during an existing residential wall CI application.





PBZ (total) – 3rd CI installer sample

PBZ (total) – Wall hole driller

PBZ (total) – 2nd wall hole driller sample





0920 – 1148

0917 – 1145

0926 – 1001

1001 – 1038

1107 – 1145

0925 – 1038

1056 – 1147

0920 – 1040

1057 – 1149

0920 – 1148

0915 – 1145

150

151

34.8

36.8

37.8

73.7

51.5

78.1

50.7

246

251

0.67

1.06

78.7

43.7

51.8

14.7

13.6

8.58

10.1

ND

ND

0.33

13.2

3.68

2.52

ND

Results of July 8, 1998, area and PBZ air sampling during a new residential attic CI application.

Area (total) – 1st attic – near entrance

Area (total) – 2nd attic – near entrance

Area (total) – Hopper sample – 1st attic install

Area (total) – Hopper sample – 2nd attic install

Area (total) – Background sample – in house

PBZ (total) – CI installer sample – 1st attic

PBZ (total) – 2nd CI installer sample – 1st attic

PBZ (total) – 3rd CI installer sample – 2nd attic

PBZ (total) – 4th CI installer sample – 2nd attic

PBZ (total) – Hopper operator sample – 1st attic

PBZ (total) – 2nd Hopper operator sample – 2nd attic

PBZ (total) – 3rd Hopper operator sample – 2nd attic

Area (respirable) – 1st attic – near entrance

Area (respirable) – 2nd attic – near entrance

Area (respirable) – Hopper sample – 1st attic install

Area (respirable) – Hopper sample – 2nd attic install

Area (respirable) – Background sample – in house

0938 – 1000

1045 – 1103

0937 – 1011

1045 – 1108

0903 – 1130

0938 – 0951

0951 – 1000

1045 – 1055

1055 – 1110

0936 – 1005

1041 – 1102

1102 – 1108

0938 – 1000

1045 – 1103

0937 – 1011

1045 – 1108

0903 – 1130

22.2

18.1

34.8

23.6

151

13.2

9.11

10.1

15.2

28.2

20.4

5.83

38.6

31.6

60.0

40.6

249

58.2

29.8

6.03

12.3

0.53

141

111

70.2

89.6

20.2

21.1

17.2

2.59

1.58

ND

ND

ND

3.78

1.02

10.2

2.36

0.18

ND



LocationSampleTime

(military)


SampleConcentration

(mg/m3)

8–hourTWA

(mg/m3)

Results of July 9, 1998, area and PBZ air sampling during two existing residential attic CI applications.



Area (total) – Hopper sample – 1st and 2nd attic

PBZ (total) – Prep. work – 2 unit attic – worker #1

PBZ (total) – Prep. work – 2 unit attic – worker #2

PBZ (total) – CI installer sample – 1st attic

PBZ (total) – 2nd CI installer sample – 1st attic

PBZ (total) – 3rd CI installer sample – 2nd attic

PBZ (total) – 4th CI installer sample – 2nd attic

PBZ (total) – Hopper operator sample – worker #1

PBZ (total) – Hopper operator sample – worker #2



Area (respirable) – Hopper sample – 1st and 2nd attic

0957 – 1041

1305 – 1325

1001 – 10571310 – 1329

0840 – 0925

0841 – 0925

0954 – 1016

1016 – 1054

1304 – 1318

1318 – 1333

0958 – 10211310 – 1329

1021 – 1057

0957 – 1041

1305 – 1325

1001 – 10571310 – 1329

44.5

20.2

76.9

45.9

45.4

22.4

38.6

14.2

15.3

42.3

36.2

73.7

33.5

130

19.1

10.9

22.8

2.17

22.5

73.8

72.7

16.2

21.0

34.8

18.5

1.22

0.89

0.93

2.21

3.56

10.3

3.25

3.45

0.15

0.15

Results of July 10, 1998, area and PBZ air sampling during an existing residential attic CI application.

Area (total) – Attic application – near entrance

Area (total) – Attic sample #2 – near entrance

Area (total) – Hopper sample




Area (respirable) – Attic application – near entrance

Area (respirable) – Hopper sample

1328 – 1341

1341 – 1355

1335 – 1407

1325 – 1344

1344 – 1403

1336 – 1407

1328 – 1356

1335 – 1407

13.3

14.3

31.8

18.9

18.9

31.4

45.7

54.8

12.8

7.68

25.8

22.1

32.1

47.1

1.09

0.55

0.57

1.72

2.15

3.04

0.06

0.04



LocationSampleTime

(military)


SampleConcentration

(mg/m3)

8–hourTWA

(mg/m3)

Results of August 10, 1998, area and PBZ air sampling during a new commercial wall CI application.



Area (total) – 2nd hopper sample

Area (total) – 3rd hopper sample




PBZ (total) – Hopper/roller operator sample

PBZ (total) – 2nd Hopper/roller operator sample

PBZ (total) – 3rd Hopper/roller operator sample

PBZ (total) – Worker with misc. tasks sample

PBZ (total) – 2nd Worker with misc. tasks sample



1117 – 1656

0924 – 1104

1104 – 1358

1358 – 1705

0925 – 1100

1138 – 1359

1359 – 1702

0927 – 1102

1102 – 1400

1400 – 1703

1142 – 1401

1401 – 1703

1117 – 1656

0924 – 1705

345

102

178

191

98.7

147

190

95.1

178

183

141

184

597

779

0.44

11.5

11.0

17.8

16.0

19.9

30.7

11.1

10.2

33.3

32.3

19.5

0.07

0.28

13.4

20.7

18.7

16.7

0.27

Results of August 11, 1998, area and PBZ air sampling during a new commercial wall CI application.



Area (total) – 2nd Hopper sample



PBZ (total) – Hopper/roller operator sample

PBZ (total) – 2nd Hopper/roller operator sample

PBZ (total) – Worker with misc. tasks sample



0856 – 1401

1043 – 1325

1325 – 1357

1123 – 1329

1329 – 1351

1134 – 1328

1328 – 1359

0935 – 10511129 – 1149

0856 – 1401

1043 – 1357

327

164

32.5

126

22.0

113

30.8

96.7

522

327

0.65

16.9

13.9

27.9

14.2

9.39

20.6

3.43

0.64

0.17

6.64

7.97

3.56

0.69

0.07



LocationSampleTime

(military)


SampleConcentration

(mg/m3)

8–hourTWA

(mg/m3)

Results of August 12, 1998, area and PBZ air sampling during two new residential attic CI applications.



Area (total) – 1st attic hopper sample

Area (total) – 2nd attic hopper sample

PBZ (total) – 1st attic CI installer sample

PBZ (total) – 2nd attic CI installer sample

PBZ (total) – 1st attic hopper operator sample

PBZ (total) – 2nd attic hopper operator sample



Area (respirable) – 1st attic hopper sample

Area (respirable) – 2nd attic hopper sample

0958 – 1035

1210 – 1343

0955 – 1042

1207 – 1356

0954 – 1042

1209 – 1356

0959 – 1043

1206 – 1355

0958 – 1035

1210 – 1343

0955 – 1042

1207 – 1356

38.5

96.7

47.8

111

48.2

107

45.0

112

62.9

158

79.5

184

0.31

0.85

6.74

0.74

3.57

3.18

9.82

8.45

1.18

ND

0.93

0.35

0.11

0.83

2.28

1.61

0.09

0.17

Results of August 13, 1998, area and PBZ air sampling during a new residential attic CI application.

Area (total) – Attic – near entrance

Area (total) – Hopper sample – rt. of hopper




PBZ (total) – 2nd hopper operator sample

Area (respirable) – Attic – near attic entrance

Area (respirable) – Hopper sample – rt. of hopper

0845 – 1050

0842 – 1052

0843 – 0949

0949 – 1054

0937 – 0947

0950 – 1051

0845 – 1050

0842 – 1052

128

133

67.5

64.7

9.95

62.3

217

221

0.72

2.73

2.99

1.27

0.82

4.20

ND

0.29

0.19

0.74

0.95

0.34

ND

0.08



LocationSampleTime

(military)


SampleConcentration

(mg/m3)

8–hourTWA

(mg/m3)

Results of September 29, 1998, area and PBZ air sampling during three new residential attic CI applications.

Area (total) – Attic sample (1st attic)

Area (total) – Attic sample (2nd attic)

Area (total) – Attic sample (3rd attic)

Area (total) – Hopper sample (1st attic)

Area (total) – Hopper sample (2nd attic)

Area (total) – Hopper sample (3rd attic)

PBZ (total) – CI installer sample (1st attic)

PBZ (total) – CI installer sample (2nd attic)

PBZ (total) – 2nd CI installer sample (2nd attic)

PBZ (total) – CI installer sample (3rd attic)

PBZ (total) – Hopper operator sample (1st attic)

PBZ (total) – Hopper operator sample (2nd attic)

PBZ (total) – Hopper operator sample (3rd attic)

Area (respirable) – Attic sample (1st attic)

Area (respirable) – Attic sample (2nd attic)

Area (respirable) – Attic sample (3rd attic)

Area (respirable) – Hopper sample (1st attic)

Area (respirable) – Hopper sample (2nd attic)

Area (respirable) – Hopper sample (3rd attic)

0937 – 1029

1314 – 1358

1642 – 1658

0931 – 1102

1311 – 1455

1639 – 1805

0929 – 1059

1312 – 1438

1438 – 1454

1635 – 1800

0931 – 1059

1311 – 1455

1639 – 1805

0937 – 1029

1314 – 1358

1642 – 1658

0931 – 1102

1311 – 1455

1639 – 1805

52.9

44.8

16.3

95.6

109

90.3

88.4

84.5

15.7

83.5

89.3

106

87.3

89.4

75.7

27.5

155

177

146

2.08

5.13

9.82

3.98

60.9

11.2

18.6

35.5

24.8

16.2

19.4

9.66

16.9

ND

ND

ND

0.13

0.17

0.27

1.02

16.0

13.5

8.68

ND

0.11



LocationSampleTime

(military)


SampleConcentration

(mg/m3)

8–hourTWA

(mg/m3)

Results of September 30, 1998, area and PBZ air sampling during two new residential attic CI applications.

Area (total) – Attic sample (1st attic)

Area (total) – Attic sample (2nd attic)

Area (total) – Hopper sample (1st attic)

Area (total) – Hopper sample (2nd attic)

PBZ (total) – CI installer sample (1st attic)

PBZ (total) – CI installer sample (2nd attic)

PBZ (total) – 2nd CI installer sample (2nd attic)


PBZ (total) – Hopper operator (2nd attic)

Area (respirable) – Attic sample (1st attic)

Area (respirable) – Attic sample (2nd attic)

Area (respirable) – Hopper sample (1st attic)

Area (respirable) – Hopper sample (2nd attic)

1247 – 1308

1545 – 1644

1245 – 1324

1540 – 1649

1243 – 1325

1540 – 1620

1620 – 1649

1245 – 1324

1540 – 1649

1247 – 1308

1545 – 1644

1245 – 1324

1540 – 1649

21.3

59.9

39.5

69.9

42.6

40.5

29.4

38.9

68.7

35.7

100

65.6

116

12.7

17.5

11.6

14.9

13.2

33.6

11.6

23.4

34.8

0.56

0.40

0.76

0.26

2.71

3.08

4.66

6.90

0.07

0.10



LocationSampleTime

(military)


SampleConcentration

(mg/m3)

8–hourTWA

(mg/m3)

Results of October 1, 1998, area and PBZ air sampling during a new residential attic CI application.

Area (total) – Attic sample




Area (respirable) – Attic sample


1009 – 1022

1009 – 1027

1008 – 1027

1009 – 1027

1009 – 1022

1009 – 1027

13.3

18.1

19.4

18.4

22.2

30.2

35.3

34.8

47.4

41.9

0.90

0.99

0.96

1.31

1.88

1.57

0.02

0.04

Results of October 2, 1998, area and PBZ air sampling during a new residential wall CI application.







PBZ (total) – 3rd hopper operator sample


0845 – 1322

0843 – 0928

0928 – 1109

1109 – 1345

0845 – 0939

0939 – 1147

1147 – 1345

0845 – 1322

277

45.9

103

159

55.2

131

121

279

3.59

36.3

24.1

27.3

16.1

12.5

15.4

0.22

2.07

17.4

8.93

0.13



LocationSampleTime

(military)


SampleConcentration

(mg/m3)

8–hourTWA

(mg/m3)

Results of December 15, 1998, area and PBZ air sampling during six new residential attic CI applications.

Area (total) – 1st attic sample – near entrance

Area (total) – 2nd attic sample – near entrance

Area (total) – 1st hopper sample – left of entrance

Area (total) – 2nd hopper sample – left of entrance

Area (total) – 3rd hopper sample – left of entrance

Area (total) – 4th hopper sample – left of entrance

PBZ (total) – 1st CI installer sample



PBZ (total) – 1st hopper operator sample



PBZ (total) – 4th hopper operator sample

Area (respirable) – 1st attic sample – near entrance

Area (respirable) – 2nd attic sample – near entrance

Area (respirable) – 1st hopper sample – left of entrance

Area (respirable) – 2nd hopper sample – left of entrance

Area (respirable) – 3rd hopper sample – left of entrance

Area (respirable) – 4th hopper sample – left of entrance

1148 – 12021252 – 13011358 – 14081419 – 1427

1624 – 16351652 – 1702

1029 – 1108

1145 – 12031248 – 1303

1356 – 1431

1620 – 16381649 – 1703

1032 – 1120

1138 – 12071247 – 13071355 – 1434

1619 – 16411649 – 1702

1029 – 1118

1139 – 12031242 – 1303

1353 – 1430

1620 – 16401649 – 1702

1148 – 12021252 – 13011358 – 14081419 – 1427

1624 – 16351652 – 1702

1029 – 1108

1145 – 12031248 – 1303

1356 – 1431

1620 – 16381649 – 1703

40.9

20.9

41.5

35.1

37.2

34.1

48.5

88.9

35.4

52.0

47.7

39.3

35.0

69.5

35.6

41.5

35.1

37.2

34.1

10.0

5.26

9.88

42.7

48.4

55.1

28.9

16.9

15.0

19.8

23.9

41.7

22.0

ND

ND

0.61

1.08

1.36

ND

1.08

10.9

7.08

8.99

ND

0.22



LocationSampleTime

(military)


SampleConcentration

(mg/m3)

8–hourTWA

(mg/m3)

Results of December 16, 1998, area and PBZ air sampling during a new residential wall CI application.


Area (total) – 1st hopper sample – ceiling of truck

Area (total) – 2nd hopper sample – ceiling of truck

Area (total) – 3rd hopper sample – ceiling of truck



PBZ (total) – 1st hopper/roller operator sample

PBZ (total) – 2nd hopper/roller operator sample


Area (respirable) – Hopper sample – ceiling of truck

1001 – 1516

1004 – 1149

1149 – 1235

1235 – 13251348 – 1520

1000 – 1117

1117 – 13231348 – 1520

1013 – 1144

1144 – 13231348 – 1519

1001 – 1516

1004 – 13251348 – 1520

263

112

48.9

151

79.8

226

96.2

201

255

507

0.72

22.4

17.8

25.2

10.7

21.0

14.0

14.0

ND

2.41

14.1

11.3

8.20

1.01



LocationSampleTime

(military)


SampleConcentration

(mg/m3)

8–hourTWA

(mg/m3)

Results of December 17, 1998, area and PBZ air sampling during three new and one existing residential attic CIapplications.

Area (total) – Attic sample – near entrance

Area (total) – Hopper sample – left of entrance



Area (respirable) – Attic sample – near entrance

Area (respirable) – Hopper sample – left of entrance

0923 – 09281030 – 10451453 – 1505

0917 – 09341020 – 10441450 – 15091526 – 1540

0915 – 09351015 – 10501449 – 15111525 – 1542

0914 – 09351020 – 10471451 – 15121525 – 1540

0923 – 09281030 – 10451453 – 1505

0917 – 09341020 – 10441450 – 15091526 – 1540

35.5

74.7

95.6

87.6

57.2

125

3.10

43.0

7.74

37.0

ND

0.88

0.21

6.63

1.52

6.48

ND

0.14

Results of December 18, 1998, area and PBZ air sampling during a new residential attic CI application.

Area (total) – Background

Area (total) – 1st hopper sample – ceiling of truck

Area (total) – 2nd hopper sample – ceiling of truck

PBZ (total) – 1st CI installer sample – prep. work



PBZ (total) – 1st hopper operator sample – prep.



Area (respirable) – Background

Area (respirable) – Hopper sample – ceiling of truck

1418 – 1732

1415 – 1623

1623 – 1733

0845 – 1304

1417 – 1621

1621 – 1735

0849 – 1306

1417 – 1620

1620 – 1733

1418 – 1732

1415 – 1733

126

139

76.0

263

126

75.0

260

125

74.0

336

334

4.13

34.2

61.3

4.34

28.3

19.6

2.08

28.8

32.2

ND

2.43

18.1

12.7

13.4

1.00



LocationSampleTime

(military)


SampleConcentration

(mg/m3)

8–hour TWA(mg/m3)

Results of February 24, 1999, area and PBZ air sampling during an existing residential attic CI application.



PBZ (total) – 1st CI installer sample – HAM

PBZ (total) – 2nd CI installer sample – HAM

PBZ (total) – Hopper operator – atticpreparation




1102 – 1222

1054 – 1237

1052 – 1143

1204 – 1236

0948 – 1041

1055 – 1234

1102 – 1222

1054 – 1237

83.4

109

104

64.9

54.5

102

137

175

36.8

202

39.7

53.3

26.2

58.3

8.54

7.14

6.13

See Hopper #1below

7.77

See H.O. #1 below

1.42

See Hopper #1below

Results of February 24, 1999, area and PBZ air sampling during an existing residential wall CI application.

Area (total) – Hopper #1 sample

Area (total) – Hopper #2 sample

PBZ (total) – CI installer #1 sample

PBZ (total) – CI installer #2 sample

PBZ (total) – Hopper operator #1 sample

PBZ (total) – Hopper operator #2 sample

Area (respirable) – Hopper #1 sample

Area (respirable) – Hopper #2 sample

1329 – 1451

1329 – 1451

1328 – 1452

1326 – 1453

1326 – 1452

1327 – 1452

1328 – 1453

1328 – 1453

87.1

88.5

86.8

90.7

88.5

85.9

140

146

60.3

61.1

10.4

3.86

18.4

44.6

1.71

8.70

53.7

10.8

1.82

0.70

18.2

7.90

1.82

1.54



LocationSampleTime

(military)


SampleConcentration

(mg/m3)

8–hourTWA

(mg/m3)




PBZ (total) – Attic preparation worker

PBZ (total) – 1st CI installer sample – HAM


PBZ (total) – Hopper operator – preparation work

PBZ (total) – 1st Hopper operator sample

PBZ (total) – 2nd Hopper operator sample – HAM



1254 – 1400

1242 – 1404

0912 – 1041

1245 – 1320

1343 – 1405

0911 – 1041

1246 – 1334

1343 – 1405

1254 – 1400

1242 – 1404

69.9

84.8

94.3

70.8

22.7

92.8

49.5

44.5

113

140

36.9

187

3.82

34.6

171

14.4

46.7

140

6.55

12.9

5.07

32.0

0.71

10.4

13.8

0.90

2.20



LocationSample Time

(military)SampleVolume(liters)

SampleConcentration

(mg/m3)

8–hourTWA

(mg/m3)

Results of March 23, 1999, area and PBZ air sampling during a new residential wall CI application.

Area (total) – Background sample


PBZ (total) – CI installer #1sample

PBZ (total) – Hopper–roller/recycle operator #2 sample


Area (respirable) – Background sample


0815 – 1147

0824 – 1144

0817 – 1150

0821 – 1155

0820 – 1150

0815 – 1147

0824 – 1144

222

205

217

215

219

366

345

1.26

9.46

22.1

61.3

34.2

ND

0.26

3.94

9.81

27.3

15.0

0.11

Results of March 24, 1999, area and PBZ air sampling during a new residential wall CI application.*



PBZ (total) – 1st CI installer #1 sample

PBZ (total) – 2nd CI installer #1 sample

PBZ (total) – 1st Hopper–roller/recycle operator #2sample

PBZ (total) – 2nd Hopper–roller/recycle operator #2sample

PBZ (total) – 1st Hopper–roller/recycle operator #3sample

PBZ (total) – 2nd Hopper–roller/recycle operator #3sample



0800 – 1230

0757 – 1230

0759 – 0951

0952 – 1237

0800 – 0953

0953 – 1239

0800 – 0952

0952 – 1239

0800 – 1230

0757 – 1230

286

286

115

170

116

170

114

171

467

472

2.03

2.87

29.3

20.6

45.7

23.4

33.8

12.9

0.17

0.17

1.63

13.9

18.9

12.4

0.10

* = #1 is Worker 1, #2 is Worker 2, and #3 is Worker 3 (worker’s number does not change duringthe week)



LocationSample Time


SampleConcentration

(mg/m3)

8–hourTWA

(mg/m3)

Results of March 25, 1999, area and PBZ air sampling during a new residential attic and wall CI application.


Area (total) – Hopper sample (attic CI install)

Area (total) – Hopper sample (wall CI install)

PBZ (total) – 1st CI installer #2 sample – attic

PBZ (total) – 2nd CI installer #2 sample – attic


PBZ (total) – 1st CI installer helper #3 sample – attic

PBZ (total) – 2nd CI installer helper #3 sample – attic

PBZ (total) – roller/recycle operator #3 sample – wallinstall & CI installer of ceiling

PBZ (total) – Hopper operator #1 sample – attic

PBZ (total) – CI installer #1 sample – wall


Area (respirable) – Hopper sample (attic CI install)

Area (respirable) – Hopper sample (wall CI install)

0837 – 1157

0830 – 1228

1350 – 1810

0824 – 1013

1013 – 1229

1352 – 1808

0822 – 1013

1013 – 1229

1352 – 1808

0830 – 1230

1351 – 1808

0837 – 1157

no sample

1350 – 1810

209

242

275

112

139

263

114

140

268

254

261

346

450

12.3

5.91

10.8

84.9

90.7

37.2

23.3

37.5

80.6

16.3

31.8

0.09

bad filter

0.40

5.13

8.78

64.8

59.0

25.2

0.04

0.40




LocationSample Time


SampleConcentration

(mg/m3)

8–hourTWA

(mg/m3)

Results of March 26, 1999, area and PBZ air sampling during a new residential attic and wall CI application.

Area (total) – Background sample – wall CI install

Area (total) – Hopper sample – wall CI install



PBZ (total) – CI installer #1 sample – wall

PBZ (total) – Hopper operator #1 sample – attic


PBZ (total) – CI installer #2 sample – attic


PBZ (total) – CI installer helper #3 sample – attic

Area (respirable) – Background sample – wall CI install

Area (respirable) – Hopper sample – wall CI install



0732 – 1020

0731 – 1027

1027 – 1240

1050 – 1235

0728 – 1027

1027 – 1243

0730 – 1027

1027 – 1244

0730 – 1025

1025 – 1247

0732 – 1020

0731 – 1027

1027 – 1240

1050 – 1235

176

181

137

110

190

144

181

140

186

151

291

305

182

230

21.7

21.9

6.20

38.3

41.1

20.2

48.9

97.3

48.5

20.2

1.79

1.08

0.91

4.51

9.75

8.38

21.1

45.8

23.7

0.65

0.99




LocationSample Time


SampleConcentration

(mg/m3)

8–hourTWA

(mg/m3)

Results of September 27, 1999, area and PBZ air sampling during a new residential wall CI application.







PBZ (total) – Worker picking–up CI sample



1122 – 1652

1128 – 1655

1120 – 1235

1343 – 1650

1138 – 1244

1343 – 1653

1217 – 12351343 – 1650

1122 – 1652

1128 – 1655

340

330

74.3

185

66

197

203

566

578

4.32

1.30

46.2

58.9

14.4

13.7

17.2

ND

ND

0.89

30.2

7.40

7.35

Results of September 28, 1999, area and PBZ air sampling during new residential attic CI applications.







PBZ (total) – Attic helper sample



1058 – 14001415 – 1607

1103 – 1618

1056 – 1236

1236 – 1611

1102 – 1155

1201 – 13311407 – 1611

1212 – 1616

1058 – 14001415 – 1607

1103 – 1618

307

333

103

222

54.0

218

248

513

546

5.21

5.83

39.2

11.9

12.6

40.9

10.1

ND

0.20

3.19

3.83

13.5

19.6

5.13

0.13



LocationSample Time


SampleConcentration

(mg/m3)

8–hourTWA

(mg/m3)

Results of September 29, 1999, area and PBZ air sampling during a new residential attic CI application.







1012 – 1134

1020 – 1202

1011 – 1155

1019 – 1200

1012 – 1134

1020 – 1202

82.0

104

105

102

139

178

2.07

8.46

16.5

51.3

0.29

ND

0.35

1.80

3.58

10.8

0.05

Results of September 30, 1999, area and PBZ air sampling during an existing residential wall CI application.



PBZ (total) – Hopper operator/drilling holes in wallsample


1010 – 1549

1011 – 12301345 – 1550

1009 – 12311348 – 1552

1010 – 1549

348

273

266

586

1.44

12.6

8.87

ND

1.02

6.93

4.92



LocationSample Time (military) Sample

Volume(liters)

SampleConcentration

(mg/m3)

8–hourTWA

(mg/m3)

Results of April 5, 2000, area and PBZ air sampling during new residential attic CI applications.


Area (total) – 1st Hopper sample


Area (total) – 3rd Hopper sample





PBZ (total) – 3rd Hopper operator sample



1405 – 1416 1733 – 17451425 – 1445 1753 – 18151511 – 1523 1842 – 19121545 – 1603 1952 – 20101714 – 1724

1357 – 1705

1705 – 1832

1832 – 2022

1403 – 1705

1705 – 2026

1353 – 1705

1705 – 1826

1848 – 2027

1405 – 1416 1733 – 17451425 – 1445 1753 – 18151511 – 1523 1842 – 19121545 – 1603 1952 – 20101714 – 1724

1357 – 2023

160

193

89.4

113

184

203

200

84

103

263

661

6.25

5.75

16.0

16.9

9.89

18.5

10.5

12.1

14.4

0.19

0.59

2.01

9.03

11.5

9.21

0.06

0.48



LocationSample Time


SampleConcentration

(mg/m3)

8–hourTWA

(mg/m3)

Results of April 6, 2000, area and PBZ air sampling during new residential wall CI applications.

Area (total) – 1st General house area sample

Area (total) – 2nd General house area sample

Area (total) – 3rd General house area sample



Area (total) – 3rd Hopper sample




PBZ (total) – 1st Hopper–roller/recycle operator sample

PBZ (total) – 2nd Hopper–roller/recycle operator sample

PBZ (total) – 3rd Hopper–roller/recycle operator sample

PBZ (total) – 1st Roller/recycle operator sample

PBZ (total) – 2nd Roller/recycle operator sample

PBZ (total) – 3rd Roller/recycle operator sample

Area (respirable) – General house area sample


0743 – 0850

1149 – 1325

1352 – 1717

0735 – 0833

1147 – 1307

1354 – 1703

0734 – 0838

1149 – 1322

1354 – 1726

0733 – 0842

1145 – 1323

1351 – 1724

0731 – 0838

1148 – 1323

1351 – 1724

0740 – 08501149 – 13251352 – 1717

0735 – 08331147 – 13071354 – 1703

67.9

97.3

208

60.6

83.6

198

67.5

98.1

224

71.2

101

220

69.3

98.2

220

643

562

1.33

3.19

6.39

14.4

2.51

23.9

16.9

31.8

68.7

35.5

39.2

48.1

18.3

20.2

29.1

0.42

0.94

3.55

11.6

38.8

34.5

19.5

0.42

0.64



LocationSample Time


SampleConcentration

(mg/m3)

8–hourTWA

(mg/m3)

Results of April 7, 2000, area and PBZ air sampling during new residential wall CI applications.

Area (total) – 1st General house area sample

Area (total) – 2nd General house area sample





PBZ (total) – 1st Hopper–roller/recycle operator sample

PBZ (total) – 2nd Hopper–roller/recycle operator sample

PBZ (total) – 1st Roller/recycle operator sample

PBZ (total) – 2nd Roller/recycle operator sample

Area (respirable) – General house area sample


1131 – 1308

1308 – 1450

1121 – 1240

1308 – 1425

1125 – 1308

1310 – 1450

1120 – 1308

1308 – 1450

1122 – 1308

1310 – 1449

1131 – 13081308 – 1450

1121 – 12401308 – 1425

105

110

80.1

78.1

107

104

113

106

110

103

347

267

4.95

5.18

14.9

33.9

22.1

41.5

30.1

41.2

13.1

15.9

0.40

0.82

2.10

7.89

13.4

15.5

6.17

0.17

0.27


B. Scanning Electron Microscopy Air Sampling Results

Contractor 2 – Scanning Electron Microscopy (SEM) Air Sampling Results.

LocationSampleTime

(minutes)

CI FiberConcentration(fibers/mm2)

Fibrous/Non–fibrous

Ratio

AverageFiber Length

(µm)

Sizerange(µm)

Results of April 27, 1998, PBZ air sampling during a new residential attic CI application.

CI installer sample #1


Hopper operator sample #1


8

3

3

5

66

73

15

13

40/60

35/65

35/65

35/65

33

39

31

24

6–>90

6–>90

7–>80

8–55

Results of April 28, 1998, PBZ air sampling during an existing residential garage ceiling CI application.





56

33

6

5

65

42

68

2

35/65

45/55

35/65

25/75

34

27

40

55

5–>100

5–>100

5–>85

50–>60

Results of April 29, 1998, PBZ air sampling during an existing residential attic CI application.





16

13

5

4

24

48

66

9

35/65

35/65

35/65

35/65

35

37

40

49

5–>100

8–>75

7–>100

7–>100

Results of April 29, 1998, PBZ air sampling during an existing residential attic CI application.





4

11

6

3

71

overloaded

41

16

40/60

40/60

35/65

42

31

36

8–>90

7–>120

8–>150


Appendix B. Contractor 3 – Scanning Electron Microscopy (SEM) Air Sampling Results.

LocationSampleTime

(minutes)



Ratio

AverageFiber Length

(µm)

Sizerange(µm)

Results of July 7, 1998, PBZ air sampling during an existing residential wall CI application.

CI installer sample

Hopper operator sample

8

2

110

5

35/65

35/65

47

27

5–>58

9–>75

Results of July 8, 1998, PBZ air sampling during a new residential attic CI application.

CI installer sample


3

7

60

32

40/60

35/65

34

27

7–>90

6–>90

Results of July 9, 1998, PBZ air sampling during two existing residential attic CI applications.

CI installer sample


6

3

22

34

30/70

35/65

31

32

5–>90

5–>80

Results of July 10, 1998, PBZ air sampling during an existing residential attic CI application.

CI installer sample


3

5

43

42

40/60

40/60

30

35

7–>90

8–>90



LocationSampleTime

(minutes)



Ratio

AverageFiber Length

(µm)

Sizerange(µm)

Results of August 10, 1998, PBZ air sampling during a new commercial wall CI application.

CI installer sample


14

12

38

47

40/60

35/65

31

29

5–>90

5–>80

Results of August 11, 1998, PBZ air sampling during a new commercial wall CI application.

CI installer sample


16

9

14

10

40/60

40/60

42

39

6–>90

5–>80

Results of August 12, 1998, PBZ air sampling during two new residential attic CI applications.

CI installer sample


7

3

5

28

35/65

35/65

19

30

7–>50

5–>85

Results of August 13, 1998, PBZ air sampling during a new residential attic CI application.

CI installer sample


7

5

6

26

40/60

35/65

35

22

5–>90

5–>80



LocationSampleTime

(minutes)



Ratio

AverageFiber Length

(µm)

Sizerange(µm)

Results of September 29, 1998, PBZ air sampling during three new residential attic CI applications.

CI installer sample


5

5

32

3

35/65

35/65

25

42

5–>90

5–>85

Results of September 30, 1998, PBZ air sampling during two new residential attic CI applications.

CI installer sample


3

6

50

13

40/60

40/60

31

32

5–>90

5–>80

Results of October 2, 1998, PBZ air sampling during a new residential wall CI application.

CI installer sample


11

12

23

16

40/60

35/65

39

36

6–>85

7–>90



LocationSampleTime

(minutes)



Ratio

AverageFiber Length

(µm)

Sizerange(µm)

Results of December 15, 1998, PBZ air sampling during six new residential attic CI applications.

CI installer sample


12

18

6

18

40/60

35/65

22

23

6–>75

5–>80

Results of December 16, 1998, PBZ air sampling during a new residential wall CI application.

CI installer sample


2

6

4

6

35/65

40/60

21

25

5–>65

5–>80

Results of December 17, 1998, PBZ air sampling during three new and one existing residential attic CIapplications.

CI installer sample


8

7

5

9

35/65

35/65

19

16

5–>70

5–>60

Results of December 18, 1998, PBZ air sampling during a new residential attic CI application.

CI installer sample


4

7

6

5

35/65

40/60

37

29

7–>80

6–>85



LocationSampleTime

(minutes)



Ratio

AverageFiber Length

(µm)

Sizerange(µm)

Results of February 24, 1999, area and PBZ air sampling during an existing residential wall CI application.

CI installer sample


12

6

11

42

35/65

35/65

18

19

5–>55

5–>65


CI installer sample


4

6

15

22

30/70

35/65

20

19

6–>85

5–>65



LocationSampleTime

(minutes)



Ratio

AverageFiber Length

(µm)

Sizerange(µm)

Results of March 23, 1999, PBZ air sampling during a new residential wall CI application.

CI installer sample


6

11

4

5

40/60

35/65

33

35

6–>85

6–>90

Results of March 24, 1999, PBZ air sampling during a new residential wall CI application.

CI installer sample


24

7

17

75

35/65

30/70

30

31

5–>75

5–>75

Results of March 25, 1999, PBZ air sampling during a new residential attic and wall CI application.

CI installer sample


25

14

28

15

30/70

35/65

20

21

5–>80

5–>100

Results of March 26, 1999, PBZ air sampling during a new residential attic and wall CI application.

CI installer sample


7

9

26

30

45/55

40/60

31

27

6–>80

5–>80



LocationSampleTime

(minutes)



Ratio

AverageFiber Length

(µm)

Sizerange(µm)

Results of September 27, 1999, PBZ air sampling during a new residential wall CI application.

CI installer sample


7

8

21

12

35/65

35/65

29

21

5–>80

7–>80

Results of September 28, 1999, PBZ air sampling during a new residential wall CI application.

CI installer sample


12

7

43

18

40/60

35/65

29

32

5–>80

5–>100

Results of September 29, 1999, PBZ air sampling during a new residential attic and wall CI application.

CI installer sample


17

13

33

25

40/60

40/60

31

26

5–>90

5–>100

Results of September 30, 1999, PBZ air sampling during a new residential attic and wall CI application.

CI installer sample


19

26

9

5

35/65

40/60

41

33

6–>90

10–>90



LocationSampleTime

(minutes)



Ratio

AverageFiber Length

(µm)

Sizerange(µm)

Results of April 5, 2000, PBZ air sampling during new residential attic CI applications.

CI installer sample


4

4

4

4

35/65

35/65

23

18

6–>80

6–>45

Results of April 6, 2000, PBZ air sampling during new residential wall CI applications.

CI installer sample


7

3

11

16

40/60

40/60

21

36

5–>85

5–>90

Results of April 7, 2000, PBZ air sampling during new residential wall CI applications.

CI installer sample


4

2

20

ND

35/65 25 5–>80


C. Bulk Cellulose Insulation Material Results

Bulk Cellulose Insulation Material – Water Extraction/Other Elemental Results – reported in µg/g.

Contractor Al As Ba Be B Sulfate Ca Cd Co Cr Cu Fe Li Mg Mn

1a

1b

ND

Trace

ND

ND

Trace

2.63

ND

ND

16580

19353

41074

48207

1122

1777

ND

ND

ND

ND

ND

ND

Trace

Trace

ND

ND

0.86

1.07

65.6

79.2

8.26

11.7

2a

2b

ND

43

ND

Trace

Trace

3.9

ND

ND

10000

5700

78000

83000

1900

320

ND

ND

Trace

ND

ND

ND

ND

ND

ND

ND

Trace

0.84

75

45

8.8

14

3 ND ND 3.3 ND 13000 95000 3100 ND ND ND Trace ND Trace 1400 13

4a

4b

49

91

ND

Trace

Trace

Trace

ND

ND

5100

7100

42000

48000

980

1700

ND

ND

ND

Trace

ND

ND

ND

ND

ND

Trace

0.92

0.86

54

77

15

14

5 110 ND ND ND 4700 36000 320 ND ND ND ND ND ND 42 20

6a

6b

6c

ND

ND

180

Trace

ND

Trace

3.9

5.5

2.2

ND

ND

Trace

7700

9800

6200

45000

55000

57000

3600

4600

4600

ND

ND

ND

Trace

ND

ND

ND

ND

ND

ND

ND

ND

ND

ND

58

ND

ND

ND

89

98

110

14

17

27

7a

7b

39

54

ND

ND

No data

No data

ND

ND

21000

20000

36000

31000

6300

4400

ND

ND

ND

Trace

ND

ND

Trace

ND

ND

ND

Trace

ND

160

110

9.5

9.0

8a

8b

120

45

Trace

Trace

No data

No data

ND

ND

5900

7500

32000

25000

2600

2500

ND

ND

ND

ND

ND

ND

Trace

ND

ND

ND

Trace

Trace

100

110

3.7

4.2

9a

9b

Trace

ND

ND

ND

No data

No data

ND

ND

25000

13000

47000

97000

2300

3500

Trace

ND

ND

ND

ND

ND

ND

ND

ND

ND

2.1

Trace

120

110

12

20

10a

10b

ND

Trace

ND

ND

No data

No data

Trace

Trace

6400

5400

31000

32000

5400

2900

ND

ND

ND

ND

ND

ND

ND

ND

ND

ND

ND

ND

170

130

18

15


Appendix C. Bulk Cellulose Insulation Material – Water Extraction/Other Elemental Results – reported in µg/g.

Contractor Mo Ni Pb P Pt Se Ag Na Te Tl Ti V Y Zn Zr

1a

1b

ND

ND

ND

ND

ND

ND

Trace

Trace

ND

ND

ND

ND

ND

ND

18577

21963

ND

ND

ND

ND

ND

ND

ND

ND

12.2

13.1

ND

ND

Trace

Trace

2a

2b

Trace

ND

ND

ND

ND

Trace

Trace

Trace

ND

ND

ND

ND

ND

ND

11000

6700

ND

ND

ND

ND

ND

ND

ND

ND

ND

ND

ND

Trace

ND

ND

3 ND ND ND ND ND ND ND 14000 ND ND ND ND ND ND ND

4a

4b

ND

ND

ND

Trace

ND

ND

2100

2700

ND

ND

ND

ND

ND

ND

760

1100

Trace

ND

ND

ND

ND

ND

Trace

Trace

ND

ND

ND

Trace

ND

ND

5 ND ND ND 3800 ND ND ND 1200 ND ND ND Trace ND ND ND

6a

6b

6c

ND

ND

ND

ND

ND

ND

ND

ND

ND

ND

ND

4200

ND

ND

ND

Trace

ND

Trace

ND

ND

ND

540

680

1100

ND

ND

ND

ND

ND

Trace

ND

ND

Trace

Trace

ND

Trace

ND

ND

ND

Trace

Trace

23

ND

ND

ND

7a

7b

ND

ND

ND

ND

ND

ND

ND

ND

Trace

Trace

ND

Trace

ND

ND

21000

19000

ND

ND

ND

ND

ND

ND

Trace

ND

ND

ND

ND

Trace

ND

ND

8a

8b

ND

Trace

ND

ND

ND

ND

250

260

Trace

ND

ND

ND

Trace

Trace

670

870

ND

ND

ND

ND

8.2

ND

Trace

Trace

ND

ND

Trace

Trace

ND

ND

9a

9b

ND

Trace

ND

ND

ND

ND

ND

ND

ND

ND

ND

ND

Trace

ND

22000

12000

ND

ND

ND

ND

ND

ND

ND

ND

Trace

ND

ND

Trace

ND

ND


10a

10b

ND

ND

ND

ND

ND

ND

2200

1800

ND

Trace

ND

ND

ND

Trace

720

620

ND

ND

ND

ND

ND

ND

ND

Trace

ND

Trace

79

67

ND

ND


Appendix C. Bulk Cellulose Insulation Material – NIOSH 7300/Strong Acid Extraction – reported in µg/g.

Contractor Al As Ba Be B Sulfate Ca Cd Co Cr Cu Fe Li Mg Mn

1a

1b

2003

1690

ND

ND

13.4

12.0

ND

ND

9243

12365

29577

35695

3334

2831

ND

ND

ND

ND

ND

ND

27.5

21.9

93.7

99.3

3.22

3.22

176

168

23.1

25.6

2a

2b

2800

1700

ND

ND

14

15

ND

ND

11000

5900

No data

No data

5100

530

ND

ND

ND

ND

ND

ND

27

8.1

150

71

3.8

Trace

200

97

23

20

3 1400 ND 9.2 ND No data 94000 3700 ND ND ND 21 61 1.5 1400 23

4a

4b

820

600

Trace

Trace

12

9.8

ND

ND

7100

6400

52000

46000

2500

1900

Trace

Trace

ND

Trace

Trace

7.7

25

24

83

95

1.1

0.98

140

130

35

37

5 2800 Trace 12 0.33 6600 41000 1200 ND ND 7.6 17 210 2.4 160 80

6a

6b

6c

2600

2600

3100

Trace

Trace

Trace

14

15

17

ND

ND

Trace

8600

9800

6300

No data

No data

No data

5600

5200

6200

ND

ND

ND

ND

ND

ND

ND

ND

Trace

25

24

32

250

120

460

2.2

3.1

2.7

190

170

230

200

32

36

7a

7b

640

1200

ND

ND

No data

No data

ND

ND

18000

15000

No data

No data

6900

7300

ND

ND

ND

ND

ND

ND

26

26

79

150

1.6

1.7

190

200

17

15

8a

8b

1700

1600

Trace

Trace

No data

No data

ND

ND

9000

8500

No data

No data

8200

7900

ND

ND

ND

ND

Trace

Trace

31

29

180

160

0.78

0.78

240

220

19

17

9a

9b

2300

2200

ND

ND

No data

No data

ND

ND

26000

14000

No data

No data

5800

4000

ND

ND

ND

ND

Trace

Trace

22

26

210

140

3.0

2.9

280

210

30

32

10a

10b

3500

1900

ND

ND

No data

No data

0.11

Trace

8100

6400

No data

No data

7500

4100

Trace

Trace

ND

ND

Trace

Trace

22

18

520

340

2.2

1.6

370

210

33

27


Appendix C. Bulk Cellulose Insulation Material – NIOSH 7300/Strong Acid Extraction – reported in µg/g.

Contractor Mo Ni Pb P Pt Se Ag Na Te Tl Ti V Y Zn Zr

1a

1b

ND

ND

ND

ND

Trace

Trace

Trace

Trace

ND

ND

ND

ND

ND

ND

15812

19093

ND

ND

ND

ND

10.3

Trace

ND

ND

30.2

19.9

Trace

Trace

ND

ND

2a

2b

ND

ND

ND

ND

ND

ND

Trace

ND

ND

ND

ND

ND

ND

ND

11000

6400

ND

ND

ND

ND

52

40

ND

ND

Trace

ND

35

Trace

Trace

ND

3 2.4 Trace Trace 24 ND ND ND 17000 ND ND 4.1 1.4 ND 26 Trace

4a

4b

ND

ND

ND

ND

ND

ND

3200

2800

ND

ND

Trace

ND

Trace

ND

1100

970

Trace

ND

ND

ND

11

8.6

2.8

2.6

0.28

0.24

40

29

1.2

1.2

5 ND ND ND 5100 ND ND Trace 1500 ND ND 51 3.8 1.1 27 2.4

6a

6b

6c

ND

ND

ND

ND

ND

ND

ND

ND

ND

500

Trace

4700

Trace

ND

ND

ND

ND

ND

ND

ND

ND

1400

800

1500

ND

ND

ND

ND

ND

ND

49

34

60

ND

Trace

6.7

ND

ND

ND

51

47

55

ND

ND

Trace

7a

7b

ND

ND

ND

ND

ND

ND

68

54

ND

ND

ND

ND

ND

ND

18000

15000

ND

ND

ND

ND

6.8

7.1

Trace

1.0

Trace

Trace

21

42

2.1

1.8

8a

8b

Trace

ND

ND

Trace

ND

ND

680

640

Trace

ND

ND

ND

13

ND

950

890

ND

ND

ND

ND

14

18

3.9

3.9

0.59

0.63

46

42

5.2

6.8

9a

9b

Trace

ND

Trace

ND

ND

ND

Trace

Trace

ND

ND

ND

ND

Trace

ND

21000

12000

Trace

Trace

ND

Trace

48

17

ND

ND

Trace

Trace

19

19

ND

2.8

10a

10b

ND

ND

Trace

ND

Trace

ND

4600

2500

ND

ND

ND

ND

ND

ND

720

740

ND

ND

ND

ND

26

20

6.0

3.4

2.3

1.4

360

140

4.8

6.8


D. Real–time Particulate Measurement Results

Estimated Particle Size Statistics from Real–time Particulate Measurements.

Date Operation PercentRespirableFraction

MMAD(µm)

GSD

Contractor #1 – Colorado

01/13/98 Preparation work inside the existing residential attic. 20 7.9 1.9

01/13/98 CI application activities in an existing residential attic. 10 15 2.5

01/13/98 CI activities in the hopper area during an existing residentialattic CI application.

5 18 2.2

01/14/98 CI activities in an existing residential attic. 2 28 2.4


1 58 2.8

Contractor #2 – Missouri

04/28/98 CI activities in the hopper area during an existing residentialgarage ceiling CI application.

11 11 1.9

04/29/98 CI activities in the truck during an existing residential attic CIapplication.

9 13 2.1


Contractor #4 – Wisconsin

08/11/98 CI activities in the hopper area during a new commercial wallCI application.

11 16 2.9

08/12/98 CI application activities in a new residential attic. 28 8.2 3.2

08/13/98 CI application activities in a new residential attic. 32 8.5 4.2

Contractor #5 – Michigan

09/29/98 CI application activities in a new residential attic. 8 15 2.4

MMAD = mass median aerodynamic diameterµm = micrometersGSD = geometric standard deviation


Appendix D. Estimated Particle Size Statistics from Real–time Particulate MeasurementsCont...

Date Operation PercentRespirableFraction

MMAD(µm)

GSD



2.5 29 2.5

02/24/99 CI activities in the hopper area during an existing residentialwall CI application.

2.5 20 2.3



1.0 55 2.8

Contractor #8 – Arizona

03/25/99 CI application activities in a new residential attic. 0 115 3.4

03/26/99 CI activities in the hopper area during a new residential atticCI application.

11 13 2.4


04/05/00 CI activities in the hopper area during a new residential atticCI application.

7 17 2.3

04/06/00 CI activities in the hopper area during a new residential wallCI application.

11 13 2.4

04/07/00 CI activities in the hopper area during a new residential wallCI application.

7 18 2.5

MMAD = mass median aerodynamic diameterµm = micrometersGSD = geometric standard deviation


Cellulose Installation Activities in Truck

0

10

20

30

40

50

60

70

16:30:10 16:31:50 16:33:30 16:35:10 16:36:50 16:38:30

Time (h:m:s)

Par

ticul

ate

Con

cent

ratio

n (m

illig

ram

s/cu

bic

met

er)

Working at hopper and/or dumping bags of cellulose

Appendix E – Figure 2. Working with bags of CI in the back of the truck

Cellulose Installation Activities in Attic

0

20

40

60

80

100

120

140

15:39:50 15:41:40 15:43:30 15:45:20 15:47:10

Time (h:m:s)

Par

ticu

late

Co

nce

ntr

atio

n

(mill

igra

ms/

cub

ic m

eter

) Working in tight areas or blowing cellulose near body

Appendix E – Figure 1. Exposure concentrations during CI activities in attic.

E. Video Exposure Monitoring Results

VEM during Contractor 1 site visit.


VEM Attic Activities

0

50

100

150

200

13:03:22 13:06:14 13:09:07 13:12:00 13:14:53 13:17:46

Time

Co

nce

ntr

atio

n (

mg

/m3) Kneeling, blowing CI against side wall.

Standing, blowing CIAgainst side wall.

Appendix E – Figure 3. VEM activities in the attic on February 26, 1999.

VEM Truck Activities

0

50

100

150

200

14:44:10 14:47:02 14:49:55 14:52:48 14:55:41 14:58:34 15:01:26

Time

Co

nce

ntr

atio

n (

mg

/m3) Peaks are Related to Dumping Bags

Appendix E – Figure 4. VEM activities in the hopper area on February 26, 1999.

Appendix E. VEM during Contractor 7 site visit.


Appendix F – Picture 1. Preparation of attic for future CI application.

Appendix F – Picture 2. Safety concern – hole created from employee fallingthrough ceiling during preparation of attic for future CI application.


Appendix F – Picture 5. Example of a wall–spray CI application and thevacuum for recycling of excess CI directly into large hopper.

Appendix F – Picture 6. Example of finished Video Exposure Monitoring toobserve employee activity and the associated total dust concentration (Real–time Monitoring also conducted – left).


Appendix F – Picture 7. Example of a group of CI fibers from SEM analysis.

Appendix F – Picture 8. Example of CI fiber. Notice the variation in fiber diameter.


G. Medical History Questionnaire

ID#______

Health Questionnaire: Cellulose Insulation StudyIDENTIFYING INFORMATION

Complete the entire form. DO NOT LEAVE ANY BLANKS.

Last Name: First Name:

Street Address: City/Town:

State: Zip Code:

Home Phone Number:

( )

Work Phone Number:

( )

Sex: 1. M G 2. F G

Date of birth: (MM/DD/YY) Age: ________

Height: feet inches

Weight: pounds

WORK HISTORY

5. In What Year Did You First Begin Working in Cellulose Insulation? 19

6. What Term Best Describes Your Current Job Title?

___________________________________________________________________________________

3. How Long Have You Worked at Your Current Job Title? ________ (Weeks / months /years) (Circle One)

4. How Many Weeks per Year Do You Perform Cellulose Insulation?

5. On Average, for the Weeks That You Perform Insulation Work, How Many Hours DoYou Work Each Week? __________ Hrs.


Date modified: March 18, 1998


Complete the entire form. DO NOT LEAVE ANY BLANKS

Indicate how often in the LAST 10 DAYS you have experienced each of the followingsymptoms.

Check only ONE column for each symptom.

SYMPTOMS Never inlast 10days

(1)

Rarely

(2)

Some-times

(3)

Often

(4)

Always

(5)

chest pain

difficulty breathing

bringing up phlegm in the morning

awakening at night short of breath

chest tightness

wheezing or whistling in chest

awakening at night with an attack ofwheezing

shortness of breath

1. Do you usually cough first thing in the morning?1. Yes G 2. No G {5}

Count a cough with the first cigarette or on first going out of doors.Exclude clearing the throat or a single cough."Usually" means 4 or more days per week.

2. Do you usually cough during the day?1. Yes G 2. No G {6}

Ignore an occasional cough."Usually" means 4 or more days per week.

(If "NO" to BOTH questions #1 and #2, go to Question #3 below.)(If "YES" to either #1 or #2 answer questions in the box below and continue.)

2a. Do you cough like this on most days for as much as three months during the year?1. Yes G 2. No G

2b. If yes, how many years have you coughed like this? __________# years.

PHLEGM

3. Do you usually bring up any phlegm from your chest on getting up, or first thing in the morning?

1. Yes G 2. No G

Count phlegm with first cigarette or on first going out of doors.Exclude phlegm from the nose.Count swallowed phlegm."Usually" means 4 or more days per week.


4. Do you usually bring up phlegm from your chest during the day?

1. Yes G 2. No G

"Usually" means 4 or more days per week.Answer "YES" if it occurs twice or more.

(If "NO" to BOTH questions #3 and #4, go to question #5.)(If "YES" to either #3 or #4, answer questions in the box below and continue.)

4a. Do you bring up phlegm like this on most days for as much as three months during the year?1. Yes G 2. No G

4b. If yes, how many years have you brought up phlegm like this? _________# years

RESPIRATORY

5. Are you troubled by shortness of breath when hurrying on level ground or walking up a slight hill?

1. Yes G 2. No G

(If "YES" to #5, answer questions in the box below. If "NO", go to question #6.)

5a. Do you get short of breath walking with other people of your own age on level ground?1. Yes G 2. No G

5b. Do you have to stop for breath when walking at a normal pace at level ground?1. Yes G 2. No G

6. Does your chest ever feel tight or your breathing become difficult?

1. Yes G 2. No G

(If "YES" to #6, continue with questions in the box below. If "NO", skip to question #7)

6a. What time of day? (choose one)G 1. No set patternG 2. Before entering the work site?G 3. After entering the work site?G 4. Shortly after leaving the work site (1-3 hours)?G 5. Some hours after leaving the work site (3-8 hours)?

6b. Are/were the attacks of chest tightness accompanied by either fever or shivering?1. Yes G 2. No G

6c. Are/were the attacks accompanied by headache?1. Yes G 2. No G

6d. Are/were the attacks accompanied by muscle ache?1. Yes G 2. No G

6e. Does your chest tightness or your breathing difficulty occur on any particular day of the week?1. Yes G 2. No

(If "YES" to #6e answer questions in the following box. If "NO", go to question #7)


6e-1. Which day? (choose one)

1. G Monday2. G Tuesday3. G Wednesday4. G Thursday5. G Friday6. G Saturday7. G Sunday

6e-2. Is the day you checked the first day of your work week?

1. Yes G2. No G

7. Do you ever have wheezing or whistling noises in your chest?1. Yes G 2. No G

(If "YES" to # 7 answer question in box below. If "NO", go to question #8)

7a. Does this happen as often as once per week?1. Yes G 2. No G

8. Have you ever had attacks of shortness of breath with wheezing?1. Yes G 2. No G

(If "YES" to #8 answer questions in box below. If "NO", go to question #9)

8a. Was your breathing absolutely normal between attacks?1. Yes G2. No G

8b. How many attacks like this have you had in the past three years? ___# attacks

8c. How many years have you had attacks like this? ______# years

9 Since childhood, have you ever had:Hay fever 1. Yes G2. No G Emphysema1. Yes G2. No G Tuberculosis1. Yes G2. No G Bronchitis 1. Yes G2. No G Pneumonia 1. Yes G2. No G

10. Have you ever had asthma? (check the number for the best answer)G1. No, I have never had asthma.G2. Yes, I had asthma as a child and it has continued as an adult.G3. Yes, I had asthma as a child, the symptoms went away, but started again.G4. Yes, I had asthma as a child, but it went away and has not returned.G5. Yes, I have asthma as an adult, but I never had it when I was a child.

"YES" to #10 answer questions in box below. If "NO", go to question #11

10a. If you have had asthma has it ever been confirmed by a physician?1. G Yes 2. G No

10b. Have you developed asthma or has your asthma gotten worse since starting work on a CI crew?1. G Yes 2. G No

10c. Have you ever taken a prescription medication for asthma?1. G Yes 2. G No


SINUS/NASAL

11. Do you usually have a stuffy nose, or drainage at the back of your nose?

1. Yes G2. No G

12. During the past 12 months, have you had two or more episodes of blocked, itchy, or runny nose?

1. Yes G2. No G

(If "YES" to #11 or #12, answer questions in the box below. If "NO" to B OTH #11 and #12, go toquestion #13)

12a.Do you usually have these nose symptoms at any particular time of year?1. Yes G 2. No G

If "Yes", which is the worst season? (choose one)1. G Winter2. G Spring3. G Summer4. G Fall

12b.When you have nose symptoms, do you usually have fever, headache, or general body ache?1. Yes G 2. No G

12c.Were these nose symptoms mainly due to one of the following? (choose one)1. G cold or flu2. G hay fever3. G other allergies4. G something else

(specify:__________________________________________________)

12d.Do the nose symptoms seem better or worse when you are away from work, such as on weekends, vacation, sick leave, or lay-off? (choose one)

1. G neither better nor worse away from work2. G better away from work3. G worse away from work


EYES

13. During the past 12 months, have your eyes been red, itchy, or watery more than twice?

1. Yes G2. No G

(If "YES" to #13, answer questions in the box below. If "NO", go to question #14)

13a.Over the past year, about how often have you noticed these eye symptoms? (choose one)1. G less than 1-2 days altogether2. G less than 7 days3. G less than 30 days4. G more than 30 days

13b.Do you usually have these eye symptoms at any particular time of the year?1. Yes G 2. No G

If "Yes" which is the worst season? (choose one)1. G Winter2. G Spring3. G Summer4. G Fall

13c.When you have eye symptoms, do you usually have fever, headache, or general body ache?1. Yes G 2. No G

13d.Were these eye symptoms mainly due to one of the following? (choose one)1. G contact lenses2. G cold or flu3. G hay fever4. G other allergies5. G something else

(specify ____________________________________________________________)

13e.Did/do the eye symptoms seem better or worse when you were away from work, such as on weekends, vacation, sick leave,or lay-off? (choose one)

1. G stayed the same2. G got better 3. G got worse


SKIN

14. During the last 12 months have you had a skin rash, dermatitis, hives, or eczema?1. Yes G2. No G

(If "YES" to #14, answer questions in box below. If "NO", go to question #15)

14a.Is/was this rash related to anything you do at work?1. G Yes 2. G No

If "YES" to #18a what is this rash related to? ________________________)

14b.What parts of your body were affected?Scalp 1. G Yes 2. G No Face 1. G Yes 2. G No Hand or arm 1. G Yes 2. G No Trunk 1. G Yes 2. G No Groin or private parts1. G Yes 2. G No Feet or legs 1. G Yes 2. G No Other 1. G Yes 2. G No

(Specify: ) 14c.Did/does your skin seem better or worse when you were away from work such as weekends, vacation, sick leave, or lay-off? (choose

one)1. G stayed the same2. G got better 3. G got worse

15. Have you seen a doctor for any problem in the last year?1. Yes G2. No GIf "Yes", please specify: _______________________________________________________________

16. Do you presently take any medications, including non-prescription medicine, for any reason?1. Yes G2. No GIf "Yes", please specify: _______________________________________________________________

SMOKING HISTORY

17. Have you smoked, altogether, as many as 5 packs of cigarettes during your entire life?1. Yes G2. No G3. Never smoked G

(If "YES" to #17, answer questions in box below. If "NO", go to “Musculoskeletal” section top of page 11)

17a.Over the years that you smoked, on average how many cigarettes do (did) you smoke?G 1. less than ½ pack per dayG 2. more than ½ to one pack per dayG 3. 1-2 packs per dayG 4. more than two packs per day

17b.How old were you when you started smoking? ________ years old

17c.If you have stopped smoking, how old were you when you stopped? ______ years old

17d.During the years that you smoked, did you ever quit for a year or more?1. Yes G 2. No G

IF "YES", ADDING ALL THE NON-SMOKING PERIODS TOGETHER FOR HOW MANY TOTAL YEARS WERE YOU NOT SMOKING? ____# years.

18. Do you regularly smoke during work?Yes G 2. No G


MUSCULOSKELETAL

1. ARE YOU:

RIGHT-HANDED LEFT-HANDED USE BOTH HANDS EQUALLY

2. WHICH HAND DO YOU MOST OFTEN USE AT WORK?

RIGHT LEFT USE BOTH HANDS EQUALLY

3. Next, we have a few questions about physical symptoms you could experience from working on a road crew.

During the last 12 months haveDuring the last 12 months have During the last 12 months haveyou had a job-related ache, you been prevented from doing your you seen a physician for thispain, discomfort, etc. in your: day's work due to this condition? condition?

NECK ___No ___Yes v ___No ___Yes v ___No ___Yes

UPPER BACK ___No ___Yes v ___No ___Yes v ___No ___Yes

LOW BACK ___No ___Yes v ___No ___Yes v ___No ___Yes

SHOULDERS ___No ___Yes v ___No ___Yes v ___No ___Yes

ELBOWS ___No ___Yes v ___No ___Yes v ___No ___Yes

WRISTS/HANDS ___No ___Yes v ___No ___Yes v ___No ___Yes

HIPS/THIGHS ___No ___Yes v ___No ___Yes v ___No ___Yes

KNEES ___No ___Yes v ___No ___Yes v ___No ___Yes

ANKLES/FEET ___No ___Yes v ___No ___Yes v ___No ___Yes

That is all the questions we have.Thank you so much for your cooperation!

Interviewer Name:

Interviewer Comments:


H. Acute Symptom Survey

Cellulose Insulation Study: Acute Symptom Survey

LAST:________________________________ FIRST: __________________________ DATE: / /

TIME (nearest qtr hour)

1) ____________ (am / pm) pre-shift

2) ____________ (am / pm)

3) ____________ (am / pm)

4) ____________ (am / pm)

5) ____________ (am / pm)

PEAK FLOW TESTS

1) Peak Flow 1: ________ Peak Flow 2: ________ Peak Flow 3: _________


3) Peak Flow 1: ________ Peak Flow 2: ________ Peak Flow 3: _________ 4) Peak Flow 1: ________ Peak Flow 2: ________ Peak Flow 3: _________


MAJOR ACTIVITIES (approx. duration)1) pre-shift: _________________________________________________________________2) _________________________________________________________________________3) _________________________________________________________________________4) _________________________________________________________________________5) _________________________________________________________________________

Duration cellulose exp. since last ques. (nearest qtr. hr.)1) ___________ (pre-shift )2) ___________ 3) ___________4) ___________5) ___________

How many cigarettes / cigars have you smoked since getting uptodayOR since the last questionnaire?

1) None ____ < 5 ____ 6-10 ____ 11-20 ____ >20 ____ last smoke time:_______2) None ____ < 5 ____ 6-10 ____ 11-20 ____ >20 ____ last smoke time:_______3) None ____ < 5 ____ 6-10 ____ 11-20 ____ >20 ____ last smoke time:_______4) None ____ < 5 ____ 6-10 ____ 11-20 ____ >20 ____ last smoke time:_______5) None ____ < 5 ____ 6-10 ____ 11-20 ____ >20 ____ last smoke time:_______

Have your EYES been burning, itchy, painful, or irritated sincegetting uptoday OR since the last questionnaire?

1) NO___ Mild___ Mod___ Severe___ Still have Sxs : Y / N If no, dur. Sxs ___ (qtrhr)

2) NO___ Mild___ Mod___ Severe___ Still have Sxs : Y / N If no, dur. Sxs ______ 3) NO___ Mild___ Mod___ Severe___ Still have Sxs : Y / N If no, dur. Sxs ______ 4) NO___ Mild___ Mod___ Severe___ Still have Sxs : Y / N If no, dur. Sxs ______ 5) NO___ Mild___ Mod___ Severe___ Still have Sxs : Y / N If no, dur. Sxs ______

Has your NOSE been burning, itchy, stuffy, or irritated sincegetting uptoday OR since the last questionnaire?



Has your THROAT been sore, dry, scratchy, or irritated sincegetting uptoday OR since the last questionnaire?




Has your SKIN been burning, itchy, irritated or developed a rashsincegetting up today OR since the last questionnaire?



Have you been bothered by COUGHING since getting up today ORsince the last questionnaire?



Have you experienced CHEST TIGHTNESS, or difficultybreathing since getting up today OR since the last questionnaire?



Have you experienced WHEEZING or whistling in your chestsincegetting up today OR since the last questionnaire?



For Information on OtherOccupational Safety and Health Concerns

Call NIOSH at:1–800–35–NIOSH (356–4674)or visit the NIOSH Web site at:

www.cdc.gov/niosh

!Delivering on the Nation’s promise:

Safety and health at work for all peoplethrough research and prevention

hhe report no. heta-2000-0332-2827, niosh …...heta 2000–0332–2827 niosh exposure assessment of...

Documents