hh7700 ops manual

Sept 10, 2007 of 35

HH7700HH7700HH7700HH7700 ((((VHFVHFVHFVHF LOWLOWLOWLOW----BANDBANDBANDBAND HandheldHandheldHandheldHandheld RRRRadioadioadioadio))))

OPERATION MANUALOPERATION MANUALOPERATION MANUALOPERATION MANUAL

September 10, 2007

PRELIMINARYPRELIMINARYPRELIMINARYPRELIMINARY

Datron World Communications

3030 Enterprise Ct.

Vista, California 92081

(760) 597-1500

Datron VHF LOW BAND Handheld RADIO

Sept 10, 2007 of 35

CONTENTSCONTENTSCONTENTSCONTENTS

1.1.1.1. APPLICATIONAPPLICATIONAPPLICATIONAPPLICATION.................................................................................................................................................................................... 5

2.2.2.2. OVEROVEROVEROVERVIEWVIEWVIEWVIEW ........................................................................................................................................................................................... 5

2.1 OPERATIVE FUNCTION ...................................................................................................................................................... 5

3.3.3.3. EXTERIOR VIEWEXTERIOR VIEWEXTERIOR VIEWEXTERIOR VIEW ................................................................................................................................................................................ 5

4444.... OPERAOPERAOPERAOPERATION MODETION MODETION MODETION MODE .............................................................................................................................................................................. 5

4.1 Radio Mode.............................................................................................................................................................................. 5

4.2 Alignment Mode...................................................................................................................................................................... 6

4.3 Programming Mode .............................................................................................................................................................. 6

4.4 Cloning Mode........................................................................................................................................................................ 6

5555.... SUMMARY OF SUMMARY OF SUMMARY OF SUMMARY OF FUNCTIONFUNCTIONFUNCTIONFUNCTION ..................................................................................................................................................................... 7

5.1 COMMON FUNCTION....................................................................................................................................................................... 7

5.2 OPERATIVE FUNCTION ................................................................................................................................................................. 7

5.3 DISPLAY FUNCTION ..................................................................................................................................................................... 9

5.4 BEEP SOUND FUNCTION ............................................................................................................................................................. 10

6666.... FUNCTIONFUNCTIONFUNCTIONFUNCTION SPECIFICATION SPECIFICATION SPECIFICATION SPECIFICATIONSSSS .............................................................................................................................................................11

6.1 TURN ON POWER .........................................................................................................................................................................11

6.2 TURN OFF POWER .......................................................................................................................................................................11

6.3 BACK UP FUNCTION ....................................................................................................................................................................11

6.4 AUDIO VOLUME SETTING............................................................................................................................................................ 12

6.5 CHANNEL SELECT ...................................................................................................................................................................... 12

6.6 CTCSS TONE........................................................................................................................................................................ 13

6.7 150Hz TONE ............................................................................................................................................................................ 13

6.8 SCAN FUNCTION ........................................................................................................................................................................ 13

6.8.1 MEMORY SCAN FUNCTION..................................................................................................................................................... 14

6.8.1.1 SCAN SEARCH ............................................................................................................................................................. 14

6.8.1.2 SCAN PAUSE ............................................................................................................................................................... 15

6.8.1.3 SCAN RESUME ............................................................................................................................................................. 15

6.8.2 PRIORITY SCAN FUNCTION ................................................................................................................................................. 15

6.8.2.1 PRIORITY SCAN SEARCH ............................................................................................................................................. 16

6.8.2.2 PRIORITY SCAN PAUSE ............................................................................................................................................... 16

6.8.2.3 DUAL WATCH PAUSE..................................................................................................................................................... 17

6.8.2.4 PRIORITY SCAN RESUME ............................................................................................................................................. 17

6.9 DUAL WATCH FUNCTION ............................................................................................................................................................. 17

6.9.1 DUAL WATCH SEARCH .......................................................................................................................................................... 18

6.9.2 PRIORITY CHANNEL PAUSE ................................................................................................................................................. 18

6.9.3 DUAL WATCH PAUSE............................................................................................................................................................ 19

6.9.4 DUAL WATCH RESUME .......................................................................................................................................................... 19


Sept 10, 2007 of 35

6.10 MONITOR FUNCTION ................................................................................................................................................................. 19

6.11 KEY LOCK FUNCTION ............................................................................................................................................................... 20

6.12 POWER SAVE FUNCTION ........................................................................................................................................................... 20

6.13 BACK LIGHT FUNCTION ........................................................................................................................................................... 20

6.14 SCRAMBLE FUNCTION ............................................................................................................................................................... 21

6.15 VOX FUNCTION ........................................................................................................................................................................ 21

6.16 WHISPER FUNCTION ................................................................................................................................................................. 21

6.17 TRANSMIT OUTPUT POWER SETTING.......................................................................................................................................... 22

6.18 SQL-LEVEL SETTING....................................................................................................................................................... 23

6.18.1 FUNCTION ABLE / DISPLAY SETTING ............................................................................................................................... 23

6.19 TIME OUT TIMER .................................................................................................................................................................... 24

6.20 BEEP SOUND............................................................................................................................................................................ 24

7777.... ALIGNMENT MODEALIGNMENT MODEALIGNMENT MODEALIGNMENT MODE ............................................................................................................................................................................ 25

7.1 ADJUSTABLE PARAMETER............................................................................................................................................................ 25

7.2 PROCEDURE ............................................................................................................................................................................... 25

7.3 COMPLETE ALIGNMENT ............................................................................................................................................................... 28

8888 PROGRAMMING MODEPROGRAMMING MODEPROGRAMMING MODEPROGRAMMING MODE.......................................................................................................................................................................... 28

8.1 FUNCTION SETTING, DISPLAY................................................................................................................................................... 28

8.2 PROGRAMABLE PARAMETERS ........................................................................................................................................................ 29

8.2.1 Common Parameters .......................................................................................................................................................... 29

8.2.2 Programmable Button Functions .................................................................................................................................... 29

8.2.3 Channel Parameter .......................................................................................................................................................... 29

8.2.4 Preset Channel Parameter ............................................................................................................................................. 30

8.3 DETAIL OF FUNCTION PARAMETERS............................................................................................................................................ 30

8.3.1 Common Parameters .......................................................................................................................................................... 30

8.3.2 Power On Beep ................................................................................................................................................................. 30

8.3.3 Key Button Beep ............................................................................................................................................................. 30

8.3.4 Rotary Beep..................................................................................................................................................................... 30

8.3.5 Low Battery Beep............................................................................................................................................................ 30

8.3.6 Battery Save On Timer................................................................................................................................................... 31

8.3.7 Battery Save Off Timer ................................................................................................................................................. 31

8.3.8 Timeout Timer ................................................................................................................................................................. 31

8.3.9 TX/Busy Lamp ................................................................................................................................................................... 31

8.3.10 Scan Speed .................................................................................................................................................................... 31

8.3.11 CTCSS Timer ................................................................................................................................................................... 31

8.3.12 LCD/Keypad Lamp ........................................................................................................................................................... 31

8.3.13 Frequency Display ........................................................................................................................................................ 31

8.4. Programmable Button Functions ....................................................................................................................................... 32

8.4.1 SCAN ................................................................................................................................................................................. 32

8.4.2 DUAL WATCH ...................................................................................................................................................................... 32

8.4.3 SCRAMBLE ........................................................................................................................................................................ 32

8.4.4 VOX ................................................................................................................................................................................ 32

8.4.5 WHISPER....................................................................................................................................................................... 32


Sept 10, 2007 of 35

8.5. Channel Parameter ................................................................................................................................................................ 32

8.5.1 Channel Number ............................................................................................................................................................... 32

8.5.2 Scan ................................................................................................................................................................................ 32

8.5.3 Channel Spacing ............................................................................................................................................................ 32

8.5.4 Receive Frequency ......................................................................................................................................................... 33

8.5.5 Transmit Frequency....................................................................................................................................................... 33

8.5.6 RX Sub Audio ................................................................................................................................................................. 33

8.5.7 TX Sub Audio ................................................................................................................................................................. 33

8.5.8 Decode ............................................................................................................................................................................ 33

8.5.9 Encode ............................................................................................................................................................................ 34

8.5.10 Lockout Type ................................................................................................................................................................ 34

8.5.11 Timeout Timer.............................................................................................................................................................. 34

8.5.12 Preset Channel Parameters ........................................................................................................................................ 34

9999.... CLONING MODECLONING MODECLONING MODECLONING MODE ................................................................................................................................................................................ 35


Sept 10, 2007 of 35

1. APPLICATION

THIS MANUAL HAS BEEN PREPARED FOR USER OF THE DATRON HH7700 (VHF LOW BAND HANDHELD RADIO)

・ Information consists of radio operation and function setting

2. OVERVIEW

2.1 FEATURES

・FREQUENCY COVERAGE

・TRANSMITTER OUTPUT POWER: 5W MAX

・CTCSS ENCODE/DECODE, 39 FREQUENCIES

・150Hz TONE FUNCTION

・PC PROGRAMABLE

・CLONING

・100 CHANNEL MEMORY BANK

・14 SEGMENT 5 DIGIT ALPHA NUMERIC LCD DISPLAY

・VOICE SCRAMBLER (OPTION)

・VOX (STANDARD)

・WHISPER (STANDARD)

3. EXTERIOR VIEW

・ANTENNA

・POWER SWITCH, AUDIO VOLUME

・PTT SWITCH

・SHIFT SWITCH

・MONITOR SWITCH

・CHANNEL SELECT

・TX / Busy LED

・EXTERAL SPEAKER MIC. JACK

・14 SEGMENT 5 DIGIT LCD

・FUNCTION KEY SWITCH

・2200mＡｈ BATTERY / 4000mAh LI-ION BATTERY

・BELT CLIP

4. OPERATION MODE

4.1 Radio Mode USER OPERATION MODE

AMONG THE FEATURES, SCAN MODE CONSISTS OF SCANNING,

PRIORITY SCANNING AND DUAL WATCH FEATURES

Band ： 30MHz ～ 87.9950MHz


Sept 10, 2007 of 35

4.2 Alignment Mode FOR RADIO ALIGNMENT, READING AND WRITING, SETTING LEVEL FOR SOME FEATURE’S FUNCTION

4.3 Programming Mode FUNCTION FEATURES SET BY PC PROGRAMMING

FUNCTION FEATURE SET, READ, WRITING, SETTING COMMANDS

4.4 Cloning Mode TRANSFER DATA MASTER/SLAVE UNIT

MASTER UNIT IS SENDING AND SLAVE UNIT IS RECEIVING DATA

OPERATION RADIO MODE KEY OPERATION

MODE [ROTARY SWITCH]

[PTT]

[MONI]、 [SHIFT]

[▲]、 [▼]、PROGRAMBLE KEY [P1] [P2]

SCAN MODE MEMORY SCAN

PRIORITY SCAN

ALIGNMENT MODE

PROGRAMING MODE

CLONING MODE CLONING MASTER MODE

CLONING SLAVE MODE


Sept 10, 2007 of 35

5. FUNCTION SUMMARY

5.1 COMMON FUNCTIONS

No. FUNCTION DETAIL

1 MONITOR FUNCTION

DISABLE MUTING FUNCTION 〔MONI〕 SWITCH

2 KEYLOCK FUNCTION DISABLE KEY ACTION EXCEPT FOR 〔PTT〕〔MONI〕 SWITCH

〔MONI〕 SWITCH PRESSING MORE THAN 2 SECONDS

3 BATTERY SAVE ACTIVATE WHEN RECEIVING CONTINUOUSLY

ON/OFF TIMING SET BY PC PROGRAMMING

4 TIME-OUT-TIMER SET TRANSMIT TIME OUT 0.5min～4.0min

5 BUSY-LOCKOUT DISABLE TRANSMIT WHEN RECEIVING CARRIER SET BY PC PROGRAMMING

6 TONE-LOCKOUT DISABLE TRANSMIT IF DOES NOT MATCH WITH CTCSS OR 150Hz TONE CODE

ONLY ABLE TO TRANSMIT WHEN MATCHED. SET BY PC PROGRAMMED

7 TX/BUSY LAMP ON/OFF ABLE OR DISABLE TX/BUSY LAMP. SET BY PC PROGRAMMING

8 BACK UP FUNCTION ALIGNED CONDITION, PARAMETER SETTING ETC.

STORED IN EEPROM (BACK UP)

9 SQL LEVEL

SETTING FUNCTION

PUSH BOTH 〔SHIFT〕 + 〔MONI〕 KEY SIMULTANEOUSLY. ABLE TO SET SQL LEVEL AT 16 POSITIONS

10 SCAN FUNTION SCAN OF SCAN LIST CHANNEL

ROTARY SWITCH SET AT [F] POSITION, SCAN SET, SCAN LIST SET BY PC PROGRAMMING

11 PRIORITY SCAN

FUNCTION

ABLE TO WORK ONLY ON PRIORITY CHANNEL LIST

ROTARY SWITCH POSITION [F] SET BY PC PROGRAMMING

12 DUAL WATCH USING CHANNEL AND PRIORITY CHANNEL (DUAL WATCH)

13 SIGNALING SWITCH

FUNCTION

CHANGE CTCSS OR 150Hz TONE

〔SHIFT〕 KEY ＋〔UP〕 KEY

14 SCRAMBLE ON/OFF

FUNCTION

VOICE SCRAMBLE ON/OFF KEY SETTING DONE BY PC PROGRAMMING

15 VOX ON/OFF VOX ON/OFF FUNCTION. KEY SETTING DONE BY PC PROGRAMMING

16 WHISPER ON/OFF WHISPER ON/OFF SETTING

17 TX POWER LEVEL SETTING TX POWER 〈HI〉〈MID〉〈LO〉 SETTING. 〔SHIFT〕 KEY ＋〔DW〕 KEY

18 BACK LIGHT OPERATION LIGHTING LCD AND KEY, SET BY PC PROGRAMMING

① On After Key(ON after any keypad PRESSED)

② Always ON

③ Disable

TURN ON 1 SECOND AFTER POWER ON, TURN ON ROTARY SWITCH OR PRESSING ANY KEY FOR 5 SECONDS,

AS LONG AS KEEP PRESSINGING WITHIN 5 SECONDS

5.2 OPERATING FUNCTION

No. FUNCTION DETAIL


Sept 10, 2007 of 35

1 〔PWR/VOL〕 POWER ON / OFF, ADJUST AUDIO LEVEL

2 〔CHANNEL〕

CHANNEL SWITCHPOSITION

SELECT CHANNEL

DISPLAY ALL PROGRAMMED CHANNELS AT [F] POSITION

DISPLAY PRESET CHANNEL AT POSITION 1～15

PRE-SET CHANNEL SET BY PC PROGRAMMING

3 〔PTT〕 SWITCH FOR TRANSMIT OR RECIVE, PRESSING FOR TRANSMITION

ALL DISABLES KEY FUNCTIONS WHEN TRANSMIT

4 〔MONI〕 RELEASE MUTE, KEY LOCK ON / OFF

1 PUSH, AUDIO MUTE ON / OFF

FOR KEY LOCK RELEASE PRESSING MORE THAN 2 SECONDS

5 EXT MIC/SPK FOR USE WITH SPK MIC. PROGRAMM PORT AS WELL

6 〔SHIFT〕 POWER SELECT, SIGNALING SWITCH, SQ LEVEL SETTING ETC.

1Push FOR FREQ. DISPLAY

[F] [SHIFT] DISABLE FOR REPEAT PUSH

[SHIFT]

[SHIFT]＋[▲] 1Push, signaling function SWITCH

[SHIFT]＋[▼] 1Push, power level SWITCH

[SHIFT]＋[MONITOR] 1Push, SQ level setting

7 〔▲〕 CHANNEL CHANGE （F POSITION）, SQ LEVEL CHANGE, SCAN MODE CHANGE

8 〔▼〕 CHANNEL CHANGE （F POSITION）, SQ LEVEL CHANGE, SCAN MODE CHANGE

9 〔P1〕 PROGRAMMABLE SWITCH SET BY PC PROGRAMMING

10 〔P2〕 PROGRAMMABLE SWITCH SET BY PC PROGRAMMING

※ABOVE 〔P1〕〔P2〕 KEY CAN BE USED AS 〔SHIFT〕＋〔P〕 KEY FOR ADDITIONAL FUNCTION OPERATION.

F 1

・

3

・

・5

7 ・ 9 ・11

・

15

13

・


Sept 10, 2007 of 35

SCAN SCMB TA

75

DT A CT

50 25

M L

5.3 DISPLAY FUNCTION

No. FUNCTION DETAILS

1 TX LED TX IS ON (RED)

2 BUSY LED RX MONITOR IS ON (GREEN)

3 LCD 14 SEGMENT 5 DIGIT CH DISPLAY OR ALPHA

4 LCD ICON DISABLE AUDIO MUTE (MONI)

5 LCD KEY LOCK ICON KEY LOCK

6 LCD DT ICON NON USE

7 LCD A ICON 150Hz TONE (ON)

8 LCD CT ICON CTCSS TONE (ON)

9 LCD SCAN ICON SCAN FUNCTION (ON)

10 LCD SCMB ICON SCRAMBLE FUNCTION (ON)

11 LCD TA ICON TALK AROUND FUNCTION (ON)

12 LCD 75 50 25 ICON FREQ USE (ON)

13 LCD L M ICON TX POWER LOW 〔L〕, MID 〔M〕 LIGHT ON

MONI ICON KEY LOCK ICON A ICON CT ICON

DT ICON SCMB ICON

SCAN ICON

TA ICON

75 50 25 ICON

L M ICON

LCD 14 SEGMENT 5 DIGIT


Sept 10, 2007 of 35

5.4 BEEP FUNCTION


1 POWER ON BEEP BEEP WHEN POWER IS ON, SET ON/OFF BY PC PROGRAMMING

2 KEY BEEP BEEP AT KEY ACTION

3 DISABLE KEY BEEP BEEP AT DISABLE KEY ACTION

4 ROTARY BEEP BEEP AT CHANNEL SWITCH ON

5 TIME OUT TIMER BEEP BEEP 10 SECOND BEFORE TIME IS UP

6 SETTING BEEP BEEP AT SETTING FUNCTION

7 SETTING FREE BEEP BEEP AT RELEASE FUNCTION SETTING

8 TX DISABLE BEEP BEEP AT PRESSING PTT WHILE DISABLE TX

9 LOW BATTERY BEEP BEEP AT VOLTABE BELOW 6.5V

※DETECT AND BEEP ONCE ONLY


Sept 10, 2007 of 35

6. FUNCTION SPECIFICATIONS

6.1 TURN ON POWER

TURN 〔PWR/VOL〕SWITCH, TO CLOCKWISE POSITION

・ GENERATE [POWER ON] BEEP

・ LCD WIL BE ON 1 SECOND, BACK LIGHT WILL BE ON 1 SECOND

THEN AFTER, GO TO STANDBY MODE

CHANNEL DISPLAY FREQUENCY DISPLAY

6.2 TURN OFF POWER

TURN OFF POWER: TURN 〔PWR/VOL〕SWITCH TO FULLY COUNTER CLOCKWISE POSITION

6.3 BACK UP FUNCTION

STORE ALL STATUS BEFORE TURN OFF IN EEPROM

THEN POWER ON AGAIN, RADIO SHOULD RESUME OPERATING STATUS AS BACKUP

BACKUP STATUS AS FOLLOW:

・ KEY LOCK STATUS

・ LAST CH (POSITION F)

・ SQ ADJ LEVEL

・ TX POWER SET LEVEL

・ SCAN MODE STATUS

・ SCRAMBLER SETTING

・ SIGNALLING STATUS

・ VOX STATUS

・ WHISPER STATUS

・ DATA SET BY PC PROGRAMMING

（１） CH STATUS

（２） CTCSS STATUS

（３） PROGRAMMABLE KEY SETTING

（４） SCAN MEMORY STATUS

（５） SCAN SPEED DATA

SCAN SCMB TA

75

DT A CT

50 25

M L

50


Sept 10, 2007 of 35

（６） CTCSS TIMER DATA

（７） PRIORITY CH DATA

（８） POWER SAVE ON/OFF

（９） POWER BEEP ON/OFF

（１０） TIME OUT TIMMER DATA

（１１） BUSY LOCK OUT DATA

（１２） TONE LOCK OUT DATA

（１３） TX/BUSY LED ON/OFF DATA

（１４） CH DATA OR FREQUENCY DATA

（１５） BACK LIGHT CONTROL DATA

・DATA SET BY PC PROGRAMMING

（１） TONE deviation (Wide)

（２） TONE deviation (Narrow)

（３） 150Hz TONE deviation(Wide)

（４） 150Hz TONE deviation(Narrow)

（５） SQL DATA

（６） LOW BATTERY THRESHOLD DATA

6.4 AUDIO VOLUME SETTING

〔PWR/VOL〕 LOUDER AT CLOCKWISE POSITION

〔PWR/VOL〕 LOWER AT COUNTER CLOCKWISE POSITION

6.5 CHANNEL SELECT

MEMORY CH 100

EACH 「Channel Parameter」 CAN BE SET BY PC PROGRAMMING

CAN CHOOSE CH OR FREQUENCY DISPLAY ON LCD

ALL SET DATA CAN BE STORED IN FLASH MEMORY

SELECT CH AS FOLLOWS:

・CHANNEL SWITCH TO 1～15

・CHANNEL SWITCH TO [F] FOR ALL CHANNEL CAN SELECT BY 〔▲〕〔▼〕 KEY

CH 16 CH 100 FREQUENCY DISPLAY

50


Sept 10, 2007 of 35

CT

・SELECT SWITCH POSITION AT NON PROGRAMMED FREQUENCY CHANNEL

NO-CH (Non Channel)

BEEP (100 mS) at NO-CH POSITION

6.6 CTCSS TONES

ENC/DEC AMONG ONE OF CTCSS (39 FREQ) PROGRAMMED FREQUENCIES

FOLLOWING PARAMETERS CAN BE SET BY PC PROGRAMMING

① PROGRAM DIFFERENT FREQ. ENC/DEC

② SET DIFFERENT TONE FREQ BY CH

6.7 150Hz TONE

〔SHIFT〕 KEY + 〔▲〕 KEY, CAN CHOOSE CTCSS⇔150Hz TONE

A ICON CT ICON

DISPLAY [ON] DISPLAY [ON]

150Hz TONE MODE CTCSS TONE MODE

6.8 SCAN FUNCTION

ABLE TO WORK AT [F] POSITION

NEED TO USE PC PROGRAMMING TO ASIGN 〔SCAN〕 RANGE

SCAN MODE SCAN DETAILS

MEMORY SCAN SCAN WITH SCAN LIST

PRIORTY SCAN SCAN PRIORITY CH AND PRIORITY SCAN LIST

A


Sept 10, 2007 of 35

DISPLAY WHILE SCANNING

MEMORY SCAN PRIORITY SCAN

CHANNEL DISPLAY

FREQUENCY

DISPLAY

〔SCAN〕 + “M” 〔SCAN〕 + “P”

6.8.1 MEMORY SCAN FUNCTION

・SCAN IF MORE THEN 2 DATA ON SCAN LIST

. [SCAN] KEY WAS SET BY PC PROGRAMMING

6.6.6.6.8888.1.1.1.1.1.1.1.1 SCAN SEARCHSCAN SEARCHSCAN SEARCHSCAN SEARCH

・SCAN MEMORY CH ON SCAN LIST

. CAN SET [SCAN] SPEED 50mＳ TO 120mS

. DEFAULT IS 80mS

. CAN SET CTSCC TIMER AS WELL AS 100mS ～ 300mS, DEFAULT IS 200mS

. EXAMPLE AS FOLLOWS:

SCAN

SCAN

SCAN

SCAN

SCAN

SCAN

50

SCAN

50


Sept 10, 2007 of 35

SCAN

6.6.6.6.8888.1.1.1.1.2.2.2.2 SCAN PAUSESCAN PAUSESCAN PAUSESCAN PAUSE

・ SCAN WILL PAUSE WHEN SQL-DET INPUT IS OFF OR MATCHED TONE FREQUENCY

・ MONITOR LCD ICON WILL BE ON

・ CH DISPLAY WILL BE FLASHED WHILE SCAN PAUSE ON /OFF TIME IS 400ｍS/400mS

・ WHEN SCAN IS [PAUSE], SQL-DET INPUT [ON], IT THEN GOES TO SCAN RESUME CONDITION

6.6.6.6.8888.1..1..1..1.3333 SCAN RESUMESCAN RESUMESCAN RESUMESCAN RESUME

・ SCAN RESUME IS （5.0 SEC）

・ [PAUSE] CH WILL BE DISPLAYED WHILE SCAN RESUMES

・ CH DISPLAY WILL CHANGED FROM FLASHING TO BLINKING WHILE SCAN RESUMES

6.8.2 PRIORITY SCAN FUNCTION

・ MUST BE LISTED IN PRIORITY CH SCAN LIST AND MORE THAN ONE CH SHOULD BE ON SCAN LIST PRESSING [SCAN]

KEY IN ORDER TO GO INTO MEMORTY SCAN SEARCH STATUS, THEN 〔▲〕 OR 〔▼〕 KEY MUST BE PRESSINGED

TO SET


Sept 10, 2007 of 35

SCAN

6.6.6.6.8888.2.1.2.1.2.1.2.1 PRIORITY SCAN SEARCHPRIORITY SCAN SEARCHPRIORITY SCAN SEARCHPRIORITY SCAN SEARCH

・ SCAN PRIORITY CHANNEL AND SCAN MEMORY CHANNEL ALTERNATELY WHICH ARE LISTED ON SCAN LIST

. SCANNING SPEED SET BY FUNCTION SOFTWARE, SCANNING SPEED WILL BE BETWEEN 50mS AND 120mS, DEFAULT IS 80mS.

. IF CTCSS TONE HAS BEEN SET, YOU ALSO NEED TO SET CTCSS TIMER. TIMER IS BETWEEN 100mS AND 300mS, DEFAULT

IS 200mS.

. ON PRIORITY CH-1, SCAN MEMORY CH-5 AND CH-16, PLEASE REFER TO THE FOLLOWING EXAMPLE.

6.6.6.6.8888.2.2.2.2.2.2.2.2 PRIORITYPRIORITYPRIORITYPRIORITY CH PAUSE CH PAUSE CH PAUSE CH PAUSE

・ DURING PRIORITY SCAN SEARCH, ON PRIORITY CH, IF SQL-DET INPUT, CHANGE TO OFF, OR CTCSS TONE ALSO HAS

BEEN SET, AND TONE FREQUENCY IS MATCHED, IT GOES TO PAUSE MODE.

・ [MONI] ICON WILL LIGHT ON

・ DURING PRIORTY SCAN PAUSE MODE, CHANNEL DISPLAY WILL BE FLASHED, SQUENCE WILL BE 400ｍS/400mS

・ DURING PRIORITY SCAN PAUSE, IF SQL-DEL INPUT CHANGES TO ON, IT WILL GO TO SCAN RESUME MODE.

SCAN

SCAN

SCAN

SCAN


Sept 10, 2007 of 35

6.6.6.6.8888.2.3.2.3.2.3.2.3 DUAL MATCH PAUSEDUAL MATCH PAUSEDUAL MATCH PAUSEDUAL MATCH PAUSE

・ DURING PRIORTIY SEARCH, ON MEMORY CH, IF SQL-DET INPUT GOES TO [F] OR CTCSS TONE FREQUENCY IS MATCHED;

IT WILL GO TO DUAL PAUSE STATUS.

・ DUAL WATCH SCAN, MEMORY CH 18 AND PRIORITY CH. MONITOR ICON WILL LIGHT UP.

・ DURING DUAL MATCH PAUSE, IF SQL-DET, INPUT COMES ON, IT WILL GO TO SCAN RESUME MODE.

RECEIVE

ALTERNATELY

SCAN MEMORY CH 1 SEC. RECEIVE PRIORITY CHANNEL

6.6.6.6.8888.2..2..2..2.4444 PRIORTY SCAN RESUMEPRIORTY SCAN RESUMEPRIORTY SCAN RESUMEPRIORTY SCAN RESUME

・ PRIORITY RESUME TIME IS FIXED （5.0 SEC）

・ DISPLAY PAUSE CHANNEL DURING PRIORITY RESUME PERIOD

・ CHANNEL DISPLAY CHANGES FROM FLASHING TO SOLID DURING PRIORITY RESUME

6.9 DUAL WATCH FUNCTION

DUAL WATCH MODE CAN BE SET AS FOLLOW:

ROTARY SW POSITION DETAIL

[F] POSITION IF USING CH AND PRIORTY CHANNEL ARE THE SAME, THEN THIS FUNCTION WILL NOT WORK

1～15 POSITION FOR DUAL WATCH POSITION, CHANNEL AND PRIORITY CHANNEL, IF PRIOIRTY CHANNEL IS

USING. THIS FUNCTION WILL NOT WORK. WHICH ARE SET BY PROGRAMMING SOFTWARE.

IF POSITION CH AND PRIORTY CH ARE THE SAME, THIS WILL NOT WORK.

DUAL WATCH DISPLAY

[DISPLAY CHANNEL] [DISPLAY FREQUENCY]

〔SCAN〕AND D ARE ON

SCAN

SCAN

SCAN

SCAN

50


Sept 10, 2007 of 35

SCAN

6.9.1 DUAL WATCH SEARCH

・ SCAN DISPLAY OR ROTARY POSITION CHANNEL AND PRIORITY CHANNEL

・ SET SCAN SPEED BY PC PROGRAMMING, SCAN SPEED, DEFAULT IS 80Ms. IT CAN BE SET BETWEEN 50mＳ AND 120m

Ｓ

・ IF CTCSS TONE IS PROGRAMMED, CTCSS TIMER ALSO CAN BE SET, DEFAULT IS 200ｍS, IT CAN BE SET BETWEEN

100mS AND 300mＳ

・ EXAMPLE, PRIORTY CH-1 IN SCAN LIST, AND DISPLAY CH-5

DISPLAY CH AND [SCAN] ICON AND D

6.9.2 PRIORITY CHANNEL PAUSE

・ DURING DUAL WATCH SEARCH, ON PRIORTY CHANNEL, SQL-DET INPUT GOES TO OFF OR CTCSS TONE FREQUENCY IS

MATCHED. IT GOES TO PRIORTY CHANNEL PAUSE

・ [MONI] ICON WILL BE DISPLAYED

・ DURING PRIORTY CHANNEL PAUSE, CHANNEL DISPLAY WILL BE FLASHING

・ DURING PRIORTY CHANNEL PAUSE, SQL-DET TIMING IS 400ｍS/400mS

・ DURING SCAN PAUSE, IF SQL-DET INPUT GOES TO [ON], IT WILL GO TO SCAN RESUME MODE

・ EXAMPLE, IN SCAN LIST, PRIORTY CH-1, DISPLAY CH-5

SCAN


Sept 10, 2007 of 35

6.9.3 DUAL WATCH PAUSE

・ DURING DUAL WATCH SEARCH, SQL-DEL INPUT GOES TO OFF OR CTCSS IS MATCHED TO PROGRAMMED FREQUENCY, IT

GOES TO DUAL WATCH MODE

・ RECEIVE ON SCAN MEMORY CHANNEL 1 SECOND AND ALSO SCANS PRIORTY CHANNEL (DUAL WATCH)

・ LCD MONI ICON WILL BE LIGHT UP

・ ON DUAL WATCH PAUSE, IF SQL-DEL INPUT GOES TO [ON], IT GOES TO CSAN RESUME MODE

・ EXAMPLE, IN SCAN LIST, PRIOIRTY CH-1, DISPLAY CH-5 ALTERNATELY

ALTERNATELY

RECEIVE

DISPLAY CH-1 SEC PRIORTY CHANNEL

6.9.4 DUAL WATCH RESUME

・ FIXED TIMING FOR DUAL WATCH RESUME (5.0 SEC）

・ DISPLAYS PAUSE CHANNEL DURING DUAL WATCH MODE

・ DURING PRIORTY RESUME, CHANNEL DISPLAY WILL BE SOLID INSTEAD OF FLASHING

6.10 MONITOR FUNCTION

PRESSING [MONI] KEY TO DISABLE MUTING （SET BEEP）

[MONI] FUNCTION WORKS AT STAND BY OR RECEIVING MODE

・BUSY LED WILL BE ON AND LCD DISPLAYS ICON

AT [MONI] STATUS, IF PRESSING [MONI] KEY AGAIN, IT WILL RELEASE [MONI] STATUS （BEEP SOUND）

・BUSY LED IS OFF （SOLID ON FOR RECEIVING）

・LCD ICON IS OFF, WHEN RECEIVING AND CTCSS TONE FREQUENCY IS MATCHED, SOLID DISPLAY WILL BE ON

SCAN

SCAN


Sept 10, 2007 of 35

6.11 KEY LOCK FUNCTION

ACTIVATES KEY LOCK FUNCTION BY PRESSINGING [MONI] KEY FOR MORE THAN 2 SECONDS（BEEP）

AT THIS STATUS, DISABLE ALL KEY ACTION EXCEPT [PTT][MONI]

RETAINS KEY LOCK STATUS EVEN WHEN POWER IS OFF, DISPLAYS ICON ON LCD

RELEASE THIS FUNCTION BY PRESSINGING [MONI] KEY MORE THAN 2 SECONDS （BEEP）

NO ICON DISPLAYED ON LCD

6.12 POWER SAVE FUNCTION

IF CONTINOUS STANDBY MODE MORE THAN 5 SECONDS BATTERY SAVE FUNCTION ACTIVATES AND MONITORING STATUS MODE

SET BATTERY SAVE ON/OFF TIMING BY PC PROGRAMMING, DEFAULT DATA WILL BE STORED IN EEPROM

・BATTERY SAVE [ON] TIME : Disable （Disable 200mS～1000mS AT 50mS INCREMENTS）

・BATTERY SAVE OFF TIME : 250mS （50mS～500mS AT 50mS RATE OF INCREMENTS）

6.13 BACK LIGHT FUNCTION

BACK LIGHT LCD AND KEY BOARD SET BY PC PROGRAMMING

① ON After Key (ON After any keypad PRESSED )

② Always ON

③ Disable

DEFAULT IS ABOVE ① ON AFTER KEY, IT WILL ILLUMIATE 1 SECOND WHEN POWER IS ON.FOR AT EVENT OF EITHER ROTARY

SWITCH OR PRESSINGING ANY KEY WILL ILLLUMIATE FOR 5 SECONDS. PRESSINGING ANY KEYS WITHIN 5 SECONDS WILL EXTEND

ILLUMINATION ANOTHER 5 SECONDS.


Sept 10, 2007 of 35

6.14 SCRAMBLER FUNCTION

USE WITH MIDIAN TVS-2 FOR OPERATION

SET SCRAMBLER ON/OFF BY PC PROGRAMMING

RETAINS SCRAMBLER ON/OFF STATUS EVEN WHEN POWER IS OFF

WHEN SCRAMBER FUNCTION ACTIVATED, DISPLAY ON LCD ICON DISPLAY

SCRAMBLE FUNCTION ON SCRAMBER FUNCTION OFF

6.15 VOX FUNCTION

SET VOX ON/OFF FUNCTION BY PC PROGRAMMING

RETAINS VOX ON/OFF STATUS EVEN WHEN POWER IS OFF

WHEN VOX IS ON, IT DISPLAYS ON LCD

HOWEVER, WHEN SCAN IS ACTIVATED, THIS WILL OVERIDE VOX OPERATION

VOX FUNCTION ON AT SCANNING VOX FUNCTION

OFF

6.16 WHISPER FUNCTION

SET WHISPER MODE ON/OFF BY PC PROGRAMMING

RETAINS WHISPER ON/OFF STATUS EVEN WHEN POWER IS OFF

WHEN WHISPER MODE IS ON, IT DISPLAYS ON LCD

HOWEVER, WHEN SCAN IS ACTIVATED, THIS WILL BE OVERIDE SCAN FUNCTION

ALSO, WHEN BOTH VOX AND WHISPER MODE ARE ON, DISPLAY ON LCD AS SHOWN BELOW:

WHISPER FUNCTION ON AT SCANNING WHISPER MODE OFF

SCMB

SCMB

SCAN

SCAN


Sept 10, 2007 of 35

BOTH WHISPER AND VOX ARE ON

6.17 TRANSMIT OUTPUT POWER SETTING

CAN SET FROM [H]、[M]、[L] 3 LEVELS

IT CAN BE SET FOR EACH CH AND DATA WILL BE STORED IN EEPROM

PRESSING [SHIFT] KEY, THEN SET BY [▼] KEY, SQUENCE IS [H]⇒[M]⇒[L]⇒[H]

ON LCD DISPLAY, NO INDICATION ON [H] HIGH POWER

[M] MEDIUM POWER, [L] LOW POWER WILL BE INDICATED

TIME OUT TIMER AND SCANNING ARE DISABLED DURING TRANSMIT

[SHIFT]

[SHIFT] [▼] KEY

OPERATING MODE TX POWER CHANGE MODE

[▼] KEY

[▼] KEY

HI POWER MID POWER LO POWER

RELASE BY PRESSINGING [SHIFT] KEY

ALSO IF NO KEY ACTIVATED DURING SET MODE, IT TERMINATES AUTOMATICALLY AFTER 5 SECONDS

M

L

M

M

L

M


Sept 10, 2007 of 35

[SHIFT] KEY OR

AFTER 5 SECONDS

TX POWER SET MODE OPERATING MODE

6.18 SET SQL-LEVEL

SET LEVEL OF SQL-DET ON/OFF SELECT FROM 16 POSITIONS

SELECT FROM 16 POSITIONS

6.18.1 SET MODE AND LEVEL

PRESSING [SHIFT] KEY FOLLOWED BY [MONI] KEY, IT GOES TO SQL-LEVEL SETTING MODE

LCD WILL CHANGE FROM CHANNEL TO SETTING MODE

USE [▲] KEY, [▼] KEY FOR LEVEL SETTING

[SHIFT]

[MONI]

[SHIFT]

OERATING MODE SQL-LEVEL SETTING MODE

［▼］ KEY [▲] KEY

RELEASE SET WITH SHIFT KEY

ALSO IF NO KEY ACTIVATED DURING SETTING MODE, IT WILL AUTOMATICALLY RELEASE SETTING MODE AFTER 5 SECONDS

[SHIFT] KEY OR

KEY ACTIVATION

AFTER 5 SECONDS

SQL-LEVEL SETTING MODE OPERATION MODE


Sept 10, 2007 of 35

6.19 TIME OUT TIMER FUNCTION

TIME OUT TIMER IS SET CONTINUOUS TRANSMIT

SET BY PC PROGRAMMING AND APPLY TO ALL CHANNELS

DEFAULT IS 3.0min SET BETWEEN 0.5min～4.0min BY 0.5min INCREMENTS

ONCE SET TIME OUT TIMER, GENERATES T-O-T BEEP SOUND 10 SECONDS PRIOR TO TIME OUT OF TRANSMISSION

6.20 BEEP SOUND

NAME OUTPUT PATTERY (1 CYCLE) REMARK

POWER [ON] BEEP 1250Hz ON/OFF BY PC PROGRAMMING

ABLE KEY BEEP

ROTARY BEEP

SETTING BEEP

1250Hz

DISABLE KEY BEEP

TX INHABIT BEEP

VACANT CH BEEP

500Hz TX INHABIT (NO TX FREQ,

PROGRAMMED) OR BUSY

CHANNEL LCOK OUT

RELEASE SETTING BEEP 1250Hz 1250Hz

TIME OUT TIMER BEEP

1500Hz 1500Hz

10 SECONDS PRIOR TO TIME

OUT

LOW BATTERY SAVE

BEEP

750Hz 1250Hz

REPEAT 5 TIMES

1. ONE BEEP AT LOW BATTERY

2. POWER IS ON

100ms

50ms

50ms

50ms 50ms 50ms

50ms 50ms 50ms

100ms 100ms 50ms


Sept 10, 2007 of 35

7. ALIGNMENT MODE

USE THIS MODE FOR ALIGNMENT OF RADIO. ALSO CAN VERIFY SOFTWARE VERSION INFORMATION

SET ROTARY SWITCH TO [F] POSITION, THEN PRESSING [SHIFT]＋[UP] KEY SIMITANEOUSELY WHILE TURNING ON POWER

STORE ALIGNEMT DATA IN EEPROM

※FREQUENCIES, TONE FREQUENCIES ETC HAVE BEEN PROGRAMMED AT FACTORY

7.1 ADJUSTABLE ELEMENT

[TRANSMITTER]

[RECEIVER]

[ETC]

7.2 ALIGNMENT PROCEDURE

ONCE ALIGNMENT MODE HAS BEEN SET, LCD DISPLAY ADJ-M（Adjust-Mode） GENERATES BEEP. THEN DISPLAY PROGRAMMING

VERSION AS SHOW BELOW:

[ADJUSTMENT MODE] DISPLAY [PROGRAMMING VERSION] DISPLAY

① SET ROTARY SWITCH FROM [F] POSITION TO [1] POSITION. IT WILL BE TONE BALANCE MODE (NOT REQUIRED)

1 TONE BALANCE （NOT REQUIRED）

2 TONE Deviation （Wide）

3 TONE Deviation （Narrow）

4 150Hz TONE Deviation （Wide）

5 150Hz TONE Deviation （Narrow）

1 SQL-LEVEL

1 LOW BATTERY THERSHOLD

2 VOX SENSITIVITY

DT


Sept 10, 2007 of 35

② CHANGE ROTARY SWITCH FROM [F] TO POSITION [1], IT GOES TO TONE DEVIATION (WIDE) MODE, GENERATES BEEP SOUND

WHEN PRESSINGING PTT SWITCH, IT WILL GO TO PRESET 2 TX FREQUENCY AND TONE FREQUENCY.

[P1] KEY

ADJUST WITH [▲] KEY [▼] KEY, PRESSING [P1] KEY WHEN FINISHED. LCD DISPLAY SET AND STORE DATA IN EEPROM, RETRY

WITH PTT SWITCH, GENERATES BEEP WHEN COMPLETE. STORE DATA IN EEPROM.

③ CHANGE ROTARY SWITCH FROM [F] TO POSITION [2], IT GOES TO TONE Deviation (Narrow) ADJUST MODE, GENERATES

BEEP SOUND, PRESSING PTT SWITCH AND DISPLY PRESET 3, TX FREQUENCY AND TONE FREQUENCY.

[P1] KEY

ADJUST WITH [▲] KEY OR [▼] KEY, PRESSING [1] KEY WHEN COMPLTE AND STORE ALL DATA IN EEPROM. RETRY WITH PRESSING

PTT SWITCH, GENERATES BEEP WHEN COMPLETE. STORE DATA IN EEPROM.

④ CHANGE ROTARY SWITCH FROM [F] TO POSITION [4], IT WILL GO TO TONE 150Hz TONE Deviation (Wide) ADJUSTMENT

MODE, GENERATES BEEP SOUND, PRESSING PTT SWITCH AND DISPLAY PRESET 4, TX FREQUENCY AND TONE FREQUENCY.

[P1] KEY

ADJUST WITH [▲] KEY OR [▼] KEY, PRESSING [1] KEY WHEN COMPLETE. LCD DISPLAY [SET] AND STORE ALL DATA IN EEPROM

RETRY WITH PRESSINGING PTT SWITCH, GENERATES BEEP WHEN COMPLETE. STORE INTERNAL VOLUMN DATA IN EEPROM.

CT

CT

A


Sept 10, 2007 of 35

⑤ CHANGE ROTARY SWITCH FROM [F] POSITION TO [5] POSITION, IT WILL GO TO 150Hz TONE Deviation (Narrow) ADJUST

MODE, GENERATES BEEP SOUND WHEN PRESSINGING PTT SWITCH AND GENERATES TX FREQUENCY WITH 150Hz TONE PROGRAMMED

CH-5

[P1] KEY

ADJUST WITH [▲] KEY OR [▼] KEY, PRESSINGING [P1] KEY WHEN COMPLETE. LCD DISPLAY [SET] AND STORE ALL DATA IN

EEPROM RETRY BY PRESSING PTT SWITCH, GENERATES BEEP WHEN COMPLETE. STORE VOLUME DATA IN EEPROM.

⑥ CHANGE ROTARY SWITCH FROM [F] POSITION TO [6], IT WILL GO TO SQL-LEVEL ADJUST MODE, GENERATES BEEP SOUND.

IT WILL GO TO STBY MODE AT PRESET PROGRAMMING CH-6 RECEIVE FREQUENCY.

[P2] KEY [P2] KEY

[P1] KEY [P1] KEY

SET OPEN-SQL-LEVEL MODE WITH [▲] KEY OR [▼] KEY, PRESSING [P1] KEY WHEN COMPLETE. MEMORIZE A/D VALUE OF SQL-DET

INPUT

TIGHT-SQL-LEVEL SET MODE WITH [▲] KEY OR [▼] KEY, PRESSING [P1] WHEN COMPLETE

LCD DISPLAYS SET AND DATA WRITING EEPROM, RETRY WITH [P2] KEY, GENERATE BEEP WHEN COMPLETE

IN CASE OF PROBLEM DISPLAYS NG, GENERATES FAILURE BEEP

⑦ TURN ROTARY SWITCH [F] POSITION TO [1] POSITION, IT WILL GO TO LOW BATTERY ADJUST MODE, GENERATES BEEP SOUND

[P2] KEY

[P1] KEY

APPLY POWER SUPPLY VOLTAGE OF 6.5V AND PRESSINGING [P1] KEY. DISPLAYS SET AND WRITE DATA IN EEPROM. RETRY BY

[P2] KEY PRESSED. GENERATES BEEP WHEN COMPLETE

⑧ SET ROTARY SWITCH [8] POSITION. THIS GOES INTO VOX SENSITIVITY ADJUST MODE

A


Sept 10, 2007 of 35

[P2] KEY

[P1] KEY

APPLY 10mVrms@1kHz, AF SIGNAL TO MIC INPUT AND PRESSING [P1] KEY, DISPLAY [SET] ON LCD, STORE DATA TO EEPROM,

TO RETRY PRESSING [P2] KEY, GENERATES BEEP WHEN COMPLETE

7.3 COMPLETE ALIGNMENT

TURN OFF POWER

8. PROGRAMMING MODE

8.1 SETTING FUNCTION AND DISPLAY

SET VARIOUS PARAMETERS BY PC PROGRAMMING, CONNECT PROGRAMMING CABLE BETWEEN PC AND MIC & SPK JACK

SET PROGRAMMING MODE BY TURN ON POWER WHILE PRESSING [MONI]＋[▼] KEY SIMULTANEOUSLY

LCD DISPLAY SHOWS PRG-M（Programming-Mode）

READING WRITING COMPLETE PROGRAM

GENERATES BEEP SOUND WHEN COMPLETE


Sept 10, 2007 of 35

8.2 PROGRAMMABLE PARAMETERS

ABLE TO SET PARAMETERS

8.2.1 Common Parameters


1 Power On Beep Enable / Disable (default Enable)

2 Key Button Beep Enable / Disable (default Enable)

3 Rotary Beep Enable / Disable (default Enable)

4 Low Battery Beep Enable / Disable (default Enable)

5 Battery Save On Timer Disable/ 200mS to 1000mS step 50mS (default Disable)

6 Battery Save Off Timer 50mS to 500mS step 50mS (default 250mS)

7 Timeout Timer 0.5min to 4.0min step 0.5min (default 3.0min)

8 TX/Busy Lamp Enable / Disable (default Enable)

9 LCD/Keypad Lamp On After Key(ON after any keypad PRESSIED)/Always ON/Disable

10 Frequency Display Enable / Disable (default Disable)

11 Scan Speed 50mS to 120mS step 10mS (default 80mS)

12 CTCSS Timer 100mS to 300mS step 10mS (default 200mS)

8.2.2 Programmable Button Functions


1 SCAN Scan function

2 DUAL WATCH Dual Watch function

3 SCRAMBLE Scramble function

4 VOX VOX function

5 WHISPER WHISPER function

8.2.3 Channel Parameter


1 Channel Number [1] to [100]

2 Scan Pri / Scan / None

3 Channel Spacing Wide / Narrow

4 Receive Frequency 30.0000MHz to 87.9950MHz / Inhibit

5 Transmit Frequency 30.0000MHz to 87.9950MHz / Inhibit

6 RX Sub Audio CTCSS / 150Hz / None

7 TX Sub Audio CTCSS / 150Hz / None

8 Decode Decode Tone(CTCSS)

9 Encode Encode Tone(CTCSS)

10 Lockout Type Busy Channel / Busy Tone / None

11 Time out Timer Enable / Disable


Sept 10, 2007 of 35

8.2.4 Preset Channel Parameter


1 Preset Channel 1～15 [1] to [100]

8.3 DETAIL OF FUNCTION PARAMETERS

8.3.1 Common Parameters

SET COMMONLY USE PARAMETERS

8.3.2 Power On Beep

SET BEEP SOUND FOR POWER ON/OFF

SET [Enable] / [Disable]

INITIAL STATUS [Enable]

IF SET [Enable], BEEP AT POWER ON

IF SET [Disable], NO BEEP AT POWER ON

8.3.3 Key Button Beep

SET BEEP AT KEY OPERATION



IF SET [Enable], BEEP ON KEY OPERATION

IF SET [Disable], NO BEEP ON KEY OPERATION

8.3.4 Rotary Beep

SET BEEP ON ROTARY SWITCH OPERATION



IF SET [Enable], BEEP ON WHEN ROTARY SWITCH

IF SET [Disable], NO BEEP ON ROTARY SWITCH

8.3.5 Low Battery Beep

SET BEEP ON Low BATTERY STATUS



IF SET [Enable], BEEP AT LOW BATTERY STATUS

IF SET [Disable], NO BEEP AT LOW BATTERY STATUS


Sept 10, 2007 of 35

8.3.6 Battery Save On Timer

SET BATTERY [SAVE ON] TIME

TIME [Disable] , [200mS] TO [1000mS] 50mS INCREMENTS

INITIAL STATUS [Disable]

8.3.7 Battery Save Off Timer

SET BATTERY [SAVE OFF] TIME

TIME [50mS] TO [500mS] 50mS INCREMENTS

INITIAL STATUS [250mS]

8.3.8 Time out Timer

SET CONTINOUS TRANSMITTING TIME

APPLY TO ALL CHANNEL

TIME [0.5min] TO [4.0min] 0.5min

INITIAL STATUS [3.0min]

8.3.9 TX/Busy Lamp

SET ABLE / DISABLE OF TX/BUSY LAMP

TIME [Enable] / [Disable]


8.3.10 Scan Speed

SET SCANNING SPEED

TIME [50mS] TO 120mS DEFAULT IS 10mS


8.3.11 CTCSS Timer

SET CTCSS TIMER

TIME [100mS] TO 300mS DEFAULT 10mS


8.3.12 LCD/Keypad Lamp

SET HOW TO LIGHT UP LCD/KEYPAD LAMP

TIME ON AFTER KEY(ON AFTER ANY KEYPAD PRESSED)/ALWAYS

ON/DISABLE

INITIAL STATUS ON AFTER KEY(ON AFTER ANY KEYPAD PRESSED)

8.3.13 Frequency Display

SET DISPLAY OF FREQUENCY LCD


INITIAL STATUS [Disable]


Sept 10, 2007 of 35

8.4. Programmable Button Functions

SET [P1], [P2] AS PROGRAMABLE BUTTON

EACH FUNCTION CAN BE ACTIVATED (1Push) FOR ON AND PUSH FOR OFF (TOGGLE ACTION) CAN SET PRIMARY AND SECONDARY

FUNCON TOGETHER

PRESSING [SHIFT] KEY [P1] OR [P2], IT GOES TO SECONDARY FUCTION OPERATION

8.4.1 SCAN

SET MEMORY SCANNING OR PRIORITY SCANNING ON / OFF

IF [ON], DISPLAYS 「SCAN」 ICON AND [M] OR [P] LETTER ON LCD

8.4.2 DUAL WATCH

SET DUAL WATCH ON / OFF

IF [ON] DISPLAYS 「SCAN」 ICON AND [D] ON LCD

8.4.3 SCRAMBLER

SET SCRAMBLER ON / OFF

IF [ON], DISPLAYS 「SCMB」 ICON ON LCD

8.4.4 VOX

SET VOX MODE ON / OFF

IF [ON], DISPLAYS 「V」 ICON ON LCD

8.4.5 WHISPER MODE

SET WHISPER MODE ON / OFF

IF [ON], DISPLAY 「W」 ICON ON LCD

8.5. Channel Parameters

8.5.1 Channel Number

8.5.2 Scan

PROGRAM SCAN LIST

TIME [Pri] / [Scan] / [None]

INITIAL STATUS [None]

ONLY ONE CHANNEL CAN BE SET [Pri]

8.5.3 Channel Spacing

PROGRAM CHANNEL SPACING

TIME [Wide] / [Narrow]

INITIAL STATUS [Wide]


Sept 10, 2007 of 35

8.5.4 Receive Frequency

SET RECEIVE FREQUENCIES

TIME 30.0000MHz ～ 87.9950MHz

INITIAL STATUS NONE（EMPTY）

8.5.5 Transmit Frequency

SET TRANSMIT FREQUENCIES

TIME 30.0000MHz ～ 87.9950MHz

INITIAL STATUS NONE (EMPTY)

8.5.6 RX Sub Audio

SET RECEIVER SUB TONE AUDIBLE

TIME [None] / [CTCSS] / [150Hz]


8.5.7 TX Sub Audio

SET TRANSMITTER SUB AUDIBLE TONE

TIME [None] / [CTCSS] / [150Hz]


8.5.8 Decode

SET SUB AUDIABLE CTCSS TONE FREUENCIES

IF SET ABOVE 8.5.6 FOR CTCSS, CHOSSOE CTCSS FREQUENCIES

IF SET ABOVE 8.5.6 FOR NONE OR 150Hz, THEN CTCSS FREQUENCIES CAN NOT BE SET.

FREQUENCIES ARE FOLLOW, INITIAL STATUS IS [OFF]

NO. FREQ.

(Hz)

NO. FREQ.

(Hz)

NO. FREQ.

(Hz)

NO. FREQ.

(Hz)

1 67.0 11 94.8 21 131.8 31 186.2

2 69.3 12 97.4 22 136.5 32 192.8

3 71.9 13 100.0 23 141.3 33 203.5

4 74.4 14 103.5 24 146.2 34 210.7

5 77.0 15 107.2 25 151.4 35 218.1

6 79.7 16 110.9 26 156.7 36 225.7

7 82.5 17 114.8 27 162.2 37 233.6

8 85.4 18 118.8 28 167.9 38 241.8

9 88.5 19 123.0 29 173.8 39 250.3

10 91.5 20 127.3 30 179.9

※ORDER OF FREQUENCIES ARE IN ACCORDANCE WITH THESE NUMBERS


Sept 10, 2007 of 35

8.5.9 Encode

SET TRANSMITTER SUB AUDIO TONE WITH [CTCSS] FREQUENCIES “TX SUB AUDIO” OR 150Hz WERE SET, THEN THIS PARAMETER

CANNOT BE PROGRAMMED

SETTING IS SAME AS [RX Sub Audio]

INITIAL STATUS IS 「OFF」

8.5.10 Lockout Type

SET LOCK OUT STATUS

SET ABLE/DISABLE WHEN SCANNING

TIME [Busy Channel] / [Busy Tone] / [None]


[Busy Channel] CANNOT TRANMIT WHEN BUSY CHANNEL IS ON

[Busy Tone] CAN TRANSMIT IF RECEIVE WITH CTCSS TONE FREQUENCY IS MATCHED

[None] CAN TRANSMIT REGARDLESS, EVEN RECEIVING CONDITION IS SET TO NONE

8.5.11 Time out Timer

Timeout Timer – SET [ABLE] / [DISABLE] OF TIME OUT TIMER



8.5.12 Preset Channel Parameters

SET CHANNEL DATA TO ROTARY 1～15 AND PRESET 1～100 CHANNEL


Sept 10, 2007 of 35

9. CLONING MODE

PROGRAMMED DATA CAN BE COPIED BETWEEN 2 RADIOS

USE CLONING CABLE BETWEEN RADIOS

MASTER IS SENDER, SLAVE IS RECEIVER

PRESSING [MONI]＋[▲] KEY SIMULTANEOUSLY WHILE POWER SWITCH IS TURNED ON

LCD DISPLAY [CLO-M] （Cloning-Mode） AND GENERATES BEEP

ONCE ACTIVES CLONING MODE, IT CHANGES TO SLAVE STATUS AND WAIT FOR RECEIVING DATA

PRESSING [P1] FOR DATA SENDING, LCD DISPLAYS [SEND]

DISPLAY RECEIVE WHEN RECEIVING DATA

SENDING PARAMETER DATA RECEIVING PARAMETER DATA

BEEP WHEN FINISHED TRANSFERING DATA AND LCD DISPLAY AS [END] FOR 2 SECONDS

AFTER

2 SEC.

GENERATES BEEP WHEN FAILED AND DISPLAYS [ERR] FOR 2 SECONDS AND STBY AGAIN

AFTER

2 SEC.

hh7700 ops manual

Documents

dual watch

sq level change

change rotary

150hz tone

generates

low battery

priorty channel

scan resume