heat sealing instruction manual
TRANSCRIPT
-
8/12/2019 HEAT SEALING Instruction Manual
1/24
LONGHILLELMSTONE HARDWICKECHELTENHAMGLOS.GL51 9TYENGLAND
Tel.: +44.(0)1242.680.680Fax: +44.(0)1242.680.909
Email: [email protected]
INSTRUCTION MANUALAUTOMATIC LID SEALING MACHINE TYPE LS4
LS4 - J17998
Issue 3
19/10/2007
T.B.S. ENGINEERING LTD
-
8/12/2019 HEAT SEALING Instruction Manual
2/24
INSTRUCTION MANUAL
T.B.S. AUTOMATIC LID SEALING MACHINE
TYPE L.S.4.
(Right to Left)
Supplied to : EXIDE INDUSTRIES LTD.
HALDIA - INDIA
Machine No. : J17998
Electrical Supply : 415V 3 phase 50 Hz
Neutral & Earth
-
8/12/2019 HEAT SEALING Instruction Manual
3/24
T.B.S. Automatic Lid Sealing Machine, Type L.S.4.
Table of Contents
1. General Data ......................................................................................................................... 1
2. Performance ......................................................................................................................... 23. Installation ............................................................................................................................ 3
1. General ..................................................................................................................... 3
2. Air Supply.................................................................................................................. 3
3. Electrical Supply ....................................................................................................... 3
4. Ventilation ................................................................................................................. 3
4. Setting Up Procedure .......................................................................................................... 4
1. Lid Box Platen........................................................................................................... 4
2. Lid Holder.................................................................................................................. 4
3. Box Positioning(1sttime) .......................................................................................... 6
4. Check Box Melt......................................................................................................... 8
5. Running the Machine........................................................................................................... 9
6. Quick Change Platen Facility............................................................................................ 10
7. Automatic Lid Loading ...................................................................................................... 13
1. Setting Up Procedure.............................................................................................. 13
2. Running the Lid Loader........................................................................................... 13
8. Maintenance ....................................................................................................................... 14
1. Daily ........................................................................................................................ 14
2. Air Cylinder Adjustments......................................................................................... 14
3. Automatic Grease Pump......................................................................................... 14
9. Standard Spares and Tools............................................................................................... 15
10. Long Term Spares............................................................................................................ 16
-
8/12/2019 HEAT SEALING Instruction Manual
4/24
T.B.S. Automatic Lid Sealing Machine, Type L.S.4. Page 1
1. General Data
Machine Type ..................... L.S.4.
Machine N ......................... J17998
Electrical Supply ................. 415V 3 phase 50 Hz - Neutral & Earth
Air Pressure........................ 80 - 100 psi (5.6 - 6.8kg/cm2)
Air Consumption ................. 0.43m/min free air compressed to 5 bar
Exhaust VentilationRequired ............................. 0.8 m/s at 25mm H2O
Overall MachineDimensions......................... Height ........... 2.55m
Length............. 3.3m (with lid loading)
Width............. 2.28m (with lid loading)
Machine Weight..................
-
8/12/2019 HEAT SEALING Instruction Manual
5/24
T.B.S. Automatic Lid Sealing Machine, Type L.S.4. Page 2
2. Performance
Cycle Time ............................. Depending upon box characteristics,up to 180 cycles / hour
Machine Capacity ................... Battery sizes falling within the following dimensionsmay be processed:
Length..180mm-540mmOverall
Height...175mm-295mmDimensions
Width....120mm-300mm
-
8/12/2019 HEAT SEALING Instruction Manual
6/24
T.B.S. Automatic Lid Sealing Machine, Type L.S.4. Page 3
3. Installation
1. General
The machine will be received as one unit complete with one set of tooling asstandard. It should be securely mounted on a solid flat base and levelled byadjustment of its four 16mm levelling screws. Adjacent gravity conveyors shouldbe adjustable in height to 800mm to enable the battery supply to flow smoothly.Bolt the machine in position using 4 off M16 fixing bolts.
If supplied with Auto Lid Loading, use the jacking feet to support its weight.
2. Air Supply
Connect a clean, dry, compressed air supplyof 5.6 - 6.8kg/cm
2(80 - 100 psi).
Set the pressure regulator to 5.6kg/cm2.
3. Electrical Supply
Connect a 3 phase supply, neutral (whereappropriate) and earth to the electrical panelsituated at the side. Make the appropriateelectrical connections in accordance with thewiring diagram.
4. Ventilation
Ventilation of suitable capacity should be connected to the machine through the200mm connection.
Supply line
-
8/12/2019 HEAT SEALING Instruction Manual
7/24
T.B.S. Automatic Lid Sealing Machine, Type L.S.4. Page 4
4. Setting Up Procedure
The following instructions are written as though new tooling is being offered for the firsttime. The machine is equipped with a number of devices to allow rapid changeover
after initial setting, these are pointed out in the text.
Similarly, the procedure is the same whether one or two batteries are processed duringeach cycle.
It is assumed that there is no tooling fitted to the machine.
Before commencing, isolate both air and electrical supplies. The platen tooling must bechanged cold to avoid injury.
1. Lid Box Platen
a) If the quick change platen facility is not fitted then change the platens from thefront of the machine. Pull the platen forward and position the lid tooling overthe appropriate fixing holes. Bolt the tooling into position using new M8 x 20long socket head cap screws and the special spring washer (LS 116). It isimportant to use new screws smeared with anti-seize. Old screws are likely tofracture. Do not over-tighten the screws.
b) Repeat the operation for the box tooling.
c) Push the platen to the back of the machine.
2. Lid Holder
a) With the lid holder on the bench, first check the operation of the lid clamp.Place lid in position using locating guides, see Fig. 1 and 2. Operate theclamp by hand with a lid fully in position. Make sure lid is clamped securely.
Fig. 1
-
8/12/2019 HEAT SEALING Instruction Manual
8/24
T.B.S. Automatic Lid Sealing Machine, Type L.S.4. Page 5
Fig. 2
b) Use two people to position the lid holder onto the main head ram. Tighten thetwo swing bolt retainers.
c) Connect the pneumatic pipes using the quick-release couplings.
d) Plug in the lid sensors. Note: If single lids, only one is powered. The correctsensor is plugged into position 1. See Fig. 3.
Fig. 3
-
8/12/2019 HEAT SEALING Instruction Manual
9/24
-
8/12/2019 HEAT SEALING Instruction Manual
10/24
T.B.S. Automatic Lid Sealing Machine, Type L.S.4. Page 7
Fig. 6
e) Place the lid(s) on the lid holder and clamp up.
f) Lower the head by venting the air to the head cylinder by means of the ballvalve located on the head cylinder. Move the boxes to align with the lids.Select battery stop auto, position the front rail and finger stops to box.
g) Adjust the clamp rail to give approximately 2mm of clearance on the box.
h) Operate the box clamp to check alignment.
i) Set the screwed rods as a position reference for both stop and front rail. Makea note of the position used for the battery type so that future setting requiresonly 3(d) and (g) to be carried out with the stops and front rail being positionedon the screwed rods. See Fig. 7.
Fig. 7
j) Close the guards and raise the head by means of the head cylinder ball valve.Remove the guard override switch so that automatic operation is obtainable.
-
8/12/2019 HEAT SEALING Instruction Manual
11/24
T.B.S. Automatic Lid Sealing Machine, Type L.S.4. Page 8
4. Check Box Melt
a) Select manual head up, cradle down, platen back.
b) Place a box or boxes with loose lids against the front rail and stops. Clamp thebattery. Close guards.
c) Bring platen forward then select cradle up for approximately 4 secondsallowing the box sealing face to melt. Lower cradle.
d) Unclamp the box and check the melt. Adjust as per 3(g).
e) Repeat the same procedure for the lid. The melt is adjusted by the adjustingscrew on top of the head assembly. The amount of melt is equal to the gapbetween the compensating block and adjusting screw.
-
8/12/2019 HEAT SEALING Instruction Manual
12/24
T.B.S. Automatic Lid Sealing Machine, Type L.S.4. Page 9
5. Running the Machine
Note: No attempt should be made to operate the machine without:-a) all guards in position.
b) ensuring that no other object other than battery boxes with loosely positionedlids enter the machine or damage to the heater platen and lid clampingassembly will result.
a) Set heating platen controller to required temperature 350C nominal and switch onheater.
Note: The heating platen takes approximately 20-30 minutes to attain 350C. Themachine will not run until the temperature is within the lower limit set on thetemperature controller.
b) Set heating time (4 seconds nominal).
c) Set cooling time (6 seconds nominal).
d) Check air supply 5.6 kg/cm (80 psi).
e) Select box clamp auto, head up, platen back, cycle auto, battery stops auto, cradledown, lid clamp.
f) Select automatic.
g) Press start button.
h) Allow one or two boxes and lids into the machine and allow a full automatic cycle tooccur.
After sealing, check alignment of box to lid and adjust the stops and front rail asnecessary.
Cut up a seal and check it is secure.
The machine is now ready to run.
-
8/12/2019 HEAT SEALING Instruction Manual
13/24
T.B.S. Automatic Lid Sealing Machine, Type L.S.4. Page 10
6. Quick Change Platen Facility
This feature is an optional extra and allows very rapid type change by allowing theheater platens to be changed for the next product type whilst the machine is running.
a) Fit the new platens as per 1a, b and c. See Fig. 8.
Fig. 8
b) Connect the thermocouple probe and heater plug and close the guard.
c) The platen will attain the temperature set on the small temperature controller withinthe main panel.
d) When ready to change the tooling, ensure that proper heat resistant clothing is wornincluding gloves and apron.
e) Lift up and hook in position the rear guard panel. See Fig. 9.
Fig. 9
f) Lift up the hinged guard.
-
8/12/2019 HEAT SEALING Instruction Manual
14/24
-
8/12/2019 HEAT SEALING Instruction Manual
15/24
T.B.S. Automatic Lid Sealing Machine, Type L.S.4. Page 12
j) Position the new platen and slide forward onto the rails. Connect the drive latch andplug in the thermocouple and heating sockets. Replace guards and turn on theplaten heating.
IMPORTANT NOTE
When coupling up the platen drive link, it is essential that the flats on the platenhandle face towards the platen (see diagram).
Failure to observe this instruction will result in the tooling being out of register withthe box and lid when the platen moves forward to the melt position.
k) Operate the platen forward / back in manual once or twice so that the limit switchrollers are correctly aligned.
l) The spare platen can be allowed to cool for changeover.
-
8/12/2019 HEAT SEALING Instruction Manual
16/24
T.B.S. Automatic Lid Sealing Machine, Type L.S.4. Page 13
7. Automatic Lid Loading
1. Setting Up Procedure
a) Select the correct lid sticks for the lid type to be run. Thread the lids onto thesticks and retain into position using the retaining clips provided. See Fig. 1.
b) Fit the correct positioning plate. See Fig. 2.
c) Load the four cassettes onto the central hub location ensuring the dowel islocated in the groove on the cassette cross bar. Lock into position.
d) Repeat this operation 4 times by closing all guard doors, selecting manual andpressing the index button. This will index the cassette system to the next stationready for changing. It is easier to change cassettes one at a time rather than
removing all four at once and then loading four new cassettes.
e) With the four cassettes in position, check the operation of each one byselecting lid feed up switch. The cams should just go flat with the operatingbar. Adjust the operating bar if necessary. See Fig. 4.
f) Position the cassette at the loading angle using the support wedge as shown inFig. 3. Slide up into position a stack of lids, pushing up on the sticks to ensurethey fully engage in the top catch assembly. See Fig. 6. The fingers are heldapart using special tool C19366 as shown.
Release the fingers and lower the cassette into its normal position. Set the lid
place fingers by slackening the clamp screw and pushing them against theskirt of the lid. Once the fingers have been set, remove the lid retaining clipsfrom the sticks. See Fig. 7.
g) Repeat (f) for the three remaining cassettes.
h) Check the manual operation of each cassette by repeating (e) for each station.
2. Running the Lid Loader
Clear any lids from the lid place trolley.
Select: Lid trolley outLid feed downLid placing auto
The lid loader will function as part of the main machine sequence. Should themachine be stopped when lids are in position on the trolley, it will be necessary toclear these before pressing the start button.
If small batches of a special lid type are to be run, it will probably be easier to runthe machine conventionally by isolating the lid loader (select lid placing manual)
and feeding the machine with boxes and loose covers.
-
8/12/2019 HEAT SEALING Instruction Manual
17/24
-
8/12/2019 HEAT SEALING Instruction Manual
18/24
T.B.S. Automatic Lid Sealing Machine, Type L.S.4. Page 15
9. Standard Spares and Tools
MACHINE SPARES PACKING LIST (BO ITEMS)
Customer EXIDE INDUSTRIES LIMITEDRef: J17998
Related M/Cs
Project: 4250
LID SEALING MACHINE
Iss.: B 02/07/2007
J17998LS4BJ18040LT3
J18035SCT4
J18036SW6
BO 010LS4 STANDARD SPARES
Part Number Qty Description
Iss: 1 26/03/2007
220 20 000 1 047 25 SOC HEAD CAP SCREW
220 20 000 1 052 25 SOC HEAD CAP SCREW
225 10 228 3 001 1 SET OF STUD STOP ADJUSTERS
232 11 000 3 001 12 S/COIL RECT/SEC SPRING WASHER
910 10 000 1 013 1 COMBINATION SPANNER 13 A/F
910 20 000 1 001 1 OPEN-ENDED SPANNER 08-10 A/F
910 20 000 1 002 1 OPEN-ENDED SPANNER 13-17 A/F
910 20 000 1 003 1 OPEN-ENDED SPANNER 17-19 A/F
910 30 000 1 001 1 RING SPANNER 17-19 A/F
920 10 000 1 001 1 ALLEN KEYS 02-10 A/F
950 40 139 1 001 1 HIGH TEMPERATURE GREASE
950 40 140 1 001 1 ANTI-SIEZE COMPOUND
950 40 142 1 001 1 COTTON GLOVES
950 40 286 1 001 1 AIR FILTER
-
8/12/2019 HEAT SEALING Instruction Manual
19/24
10. Long Term Spares
SPARES IDENTIFICATION LIST
LS4BCustomer:
J17998
EXIDE INDUSTRIES LIMITED
IC1 Issue 05/10/2007
Job number J17998
Part number Schedule Item Qty Description
BO 082 25211 40 000 1 003 0- LOCKNUT
BO 082 8231 10 000 1 005 0- FORM A PLAIN STEEL WASHER
BO 082 12231 10 000 1 006 0- FORM A PLAIN STEEL WASHER
BO 082 10410 10 102 1 135 0- BUSH
BO 082 11440 10 102 1 005 0- THRUST WASHER
BO 082 24470 30 000 1 004 0- M6 STRAIGHT GREASE NIPPLE
BO 082 18500 20 000 1 001 0- 08B1#
BO 082 1500 22 000 1 001 0- SPRING CLIP
BO 082 21511 10 292 1 023 0- CHAIN GUIDE/CHANNEL
BO 014 3560 20 000 1 021 0- T/LOCK BUSH
BO 082 27575 15 318 1 083 0- GEARMOTOR 0.37Kw 87,5rpm
BO 082 26580 10 203 0 001 0- TENSIONER SPAN BOX
BO 082 15810 10 320 1 011 0- FRICTION ACCUMULATION ROLLER
Page 1 of 6 Printed 05/10/2007
-
8/12/2019 HEAT SEALING Instruction Manual
20/24
Customer:
J17998
EXIDE INDUSTRIES LIMITED
LS4 Issue 05/10/2007
Job number J17998
Part number Schedule Item Qty Description
BO 001g 2E105 10 111 1 005 0- HEAD, SPRING RETURN
BO 001i 2E 0-
BO 001g 2E105 10 111 1 006 0- FIXED BODY/CONTACT ASSY
BO 001i 2E 0-
BO 001g 2E105 10 111 1 010 0- ROLLER LEVER STEEL
BO 001i 2E 0-
BO 001i 2E105 40 107 1 001 0- GUARD SWITCH
BO 001f 1E105 70 321 1 006 0- LONG RANGE IND SENSOR (7mm)
BO 001b 11110 10 321 1 001 0- MAGNETIC CYL. SENSOR
BO 001h 2E110 50 321 1 003 0- M18 DIFFUSE PHOTOCELL
BO 001g 2E112 10 144 1 005 0- MINIATURE PLUG
BO 001g 2E112 10 144 1 006 0- INSULATING BOOT
BO 003 17112 10 204 1 003 0- 40A MODULE, TURNED CRIMP MALE
BO 001g 2E112 10 204 1 004 0- 40A MODULE, TURNED CRIMP FEM
BO 003 18112 10 204 1 005 0- 4.0mm TURNED CRIMP MALE PINS
BO 001g 2E112 10 204 1 006 0- 4.0mm TURNED CRIMP FEMALE PIN
BO 001g 2E112 10 204 1 021 0- HBE 6 PANEL BASE WITH LID
BO 003 14112 10 204 1 022 0- HBE 6 SIDE ENTRY HOOD (PG16)
BO 003 16112 10 204 1 030 0- 2 WAY FEMALE FRAME
BO 001g 2E112 10 204 1 031 0- 2 WAY MALE FRAME
BO 001b 29115 10 321 1 003 0- 5M 90 DEG CONNECTOR, M12 4 PIN
BO 001f 2E115 10 321 1 005 0- 10M 90 DEG CONNECTOR, M12 4PIN
BO 001h 2E 0-
BO 003 11130 10 120 1 004 0- THERMOCOUPLE
BO 001g 2E130 15 120 1 003 0- THERMOCOUPLE SOCKET
BO 003 8160 10 147 3 017 0- HEATER 1200W 230V 12.625"lg 24"tails HEATING ELEMENT
BO 003 12160 10 147 3 018 0- HEATER 1600W 230V 13"long 24"tails HEATING ELEMENT
BO 003 5190 10 000 1 006 0- NEUTRAL LINK
BO 001e 95210 60 164 1 003 0- M10 TEE NUT
BO 001b 23211 40 000 1 005 0- LOCKNUT
BO 001e 90 0-
BO 001h 2E 0-
BO 001b 12211 40 000 1 011 0- LOCKNUT
BO 010 3225 10 228 3 001 0- SET OF STUD STOP ADJUSTERS
BO 001e 94231 20 164 1 002 0- JIG WASHER
BO 010 4232 11 000 3 001 0- S/COIL RECT/SEC SPRING WASHER
BO 001b 17260 10 164 1 001 0- LOCATION PIN
BO 001b 18260 10 164 1 003 0- LOCATION PIN
BO 001f 2E260 20 164 1 002 0- SPRING PLUNGER
BO 001c 39260 20 164 1 007 0- INDEX PLUNGER
BO 001i 2E270 10 000 1 001 0- 606SA CHROME HANDLE
BO 001f 2E270 10 164 1 033 0- CLAMPING HANDLE
BO 001f 1E270 10 164 1 034 0- CLAMPING HANDLE
BO 001e 92270 10 164 1 035 0- CLAMPING HANDLE
Page 2 of 6 Printed 05/10/2007
-
8/12/2019 HEAT SEALING Instruction Manual
21/24
Customer:
J17998
EXIDE INDUSTRIES LIMITED
LS4 Issue 05/10/2007
Job number J17998
Part number Schedule Item Qty Description
BO 001c 48270 10 164 1 043 0- CLAMPING HANDLE
BO 001f 2E295 10 118 1 004 0- COMPRESSION SPRING
BO 001d 65295 10 118 1 015 0- COMPRESSION SPRING
BO 001i 2E297 30 000 1 001 0- 13 BRASS BULLET CATCH
BO 001i 2E297 30 000 1 002 0- 3" x 1" ALUMINIUM BARREL BOLT
BO 001i 2E297 40 304 1 001 0- CABINET BARREL LOCK
BO 001b 13300 00 105 1 022 0- 32x80 STROKE CYLINDER
BO 001d 54300 00 105 1 043 0- 80x150 STROKE CYLINDER
BO 001c 34300 00 105 1 052 0- 100x200 STROKE C/TRUNNION CYLINDER
BO 001c 44300 00 105 1 087 0- 32x050 STROKE CYLINDER
BO 001e 89300 00 105 1 089 0- 32x25 STROKE CYLINDER
BO 001h 2E 0-
BO 001b 10300 01 105 1 016 0- 80x250 STROKE MAG.CYLINDER WITH VITON SEALS
BO 001f 1E300 15 117 1 002 0- 20x25 STROKE CYLINDER
BO 001d 55305 00 105 1 015 0- 80/100 PISTON ROD CLEVIS
BO 001d 56305 00 105 1 019 0- 80 REAR MALE TRUNNION
BO 001d 57305 00 105 1 022 0- 80 REAR TRUNNION
BO 011 6360 10 117 1 007 0- BANJO FLOW REGULATOR
BO 011 3365 10 221 1 002 0- CHECK UNIT 1/8" BSP
BO 011 4365 10 221 1 003 0- CHECK UNIT ADAPTOR 1/8" BSP
BO 011 2370 30 109 1 003 0- 1/2" BALL VALVE, VENTED
BO 011 5385 40 116 1 002 0- NON RETURN CHECK VALVE
BO 011 7385 50 116 1 003 0- POPPET VALVE
BO 003 2400 40 110 1 007 0- DRAWN CUP NEEDLE ROLLER BEARIN
BO 001d 60400 40 110 1 008 0- DRAWN CUP NEEDLE ROLLER BEARIN
BO 001d 61400 40 110 1 015 0- INNER RING FOR NEEDLE BEARING
BO 001c 30405 10 168 1 001 0- LINEAR BEARING WITH SEAL
BO 001b 14405 10 168 1 003 0- LINEAR BEARING WITH SEAL
BO 001c 47410 10 102 1 002 0- BUSH
BO 001f 2E410 10 102 1 019 0- BUSH
BO 001f 2E410 10 102 1 034 0- BUSH
BO 001f 1E410 10 102 1 044 0- BUSH
BO 001h 2E410 10 102 1 045 0- BUSH
BO 001e 91410 10 102 1 051 0- BUSH
BO 001d 59425 10 103 1 030 0- SELF LUBE BEARING UNIT
BO 001f 2E440 10 102 1 004 0- THRUST WASHER
BO 001d 62440 10 110 1 002 0- BEARING WASHER
BO 001d 63470 30 000 1 004 0- M6 STRAIGHT GREASE NIPPLE
BO 001c 41730 10 000 1 002 0- 'O' RING
BO 001d 73750 10 134 1 015 0- HEX JAM NUT
BO 001d 72750 10 134 1 026 0- SHOCK ABSORBER
BO 001d 58750 10 161 1 001 0- SHOCK ABSORBER
BO 001b 28750 10 161 1 003 0- SHOCK ABSORBER
Page 3 of 6 Printed 05/10/2007
-
8/12/2019 HEAT SEALING Instruction Manual
22/24
Customer:
J17998
EXIDE INDUSTRIES LIMITED
LS4 Issue 05/10/2007
Job number J17998
Part number Schedule Item Qty Description
BO 001l 2E950 40 286 1 001 0- AIR FILTER
BO 001i 2E950 46 000 1 002 0- PERSPEX SHEET 940x412x8 THICK
Page 4 of 6 Printed 05/10/2007
-
8/12/2019 HEAT SEALING Instruction Manual
23/24
Customer:
J17998
EXIDE INDUSTRIES LIMITED
LS4B Issue 05/10/2007
Job number J17998
Part number Schedule Item Qty Description
D65803310 00 121 1 059 0- ISO 1 5/2 SOL/SOL VALVE
D65803310 00 121 1 061 0- ISO 2 5/2 SOL/SOL VALVE
D65803355 10 121 1 006 0- FILTER
D65803360 20 121 1 019 0- PRESSURE REGULATOR 3/8"
D65803360 20 121 1 026 0- PRESSURE REGULATOR 1/4"
D65803360 20 121 1 034 0- REGULATOR
D65803363 10 121 1 003 0- LUBRICATOR
Page 5 of 6 Printed 05/10/2007
-
8/12/2019 HEAT SEALING Instruction Manual
24/24